Volkswagen Golf > VW Rabbit GTI 2006-> (A5)

Size: px
Start display at page:

Download "Volkswagen Golf > VW Rabbit GTI 2006-> (A5)"

Transcription

1 Volkswagen Golf > VW Rabbit GTI 2006-> (A5) A/C Refrigerant System General information Note: General A/C refrigerant system servicing procedures (e.g., component/system descriptions, extracting refrigerant, recharging, leak detection, troubleshooting etc.), repair and special tool information Repair Manual, Refrigerant R134a - Servicing, Repair Group 00, Specific A/C refrigerant system servicing procedures (e.g., component removal, installation and capacities) 87-5, A/C Refrigerant System, servicing. Additional information: Electrical Wiring Diagrams, Troubleshooting and Component Locations binder

2 Semi-automatic A/C System - Climatic Page 1 / Semi-automatic A/C System - Climatic General information Before troubleshooting or servicing, technicians must be familiar with the functions and operation specifics of the standard or optional A/C system. Always read the owners manual and review applicable system functions. Note: Additional information: Owners Manual Self Study Program - Course Number "VW 2006 GTI Introduction" Wiring Diagrams and Component Locations On Board Diagnostic (OBD), functions Climatic system functions are controlled by the A/C Control Module J301 which has On Board Diagnostic (OBD) capability. If malfunctions occur in monitored components, Diagnostic Trouble Codes (DTC) will be stored in memory. Troubleshoot Climatic system malfunctions by performing OBD program using Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding". Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/ Connect VAS 5051/5052 to vehicle Data Link Connector (DLC) - Select operating mode "Guided Fault Finding" - Enter appropriate model, equipment and model year information and press ">" After all control modules have been registered and DTC memories checked, - Press "Go to" - Select "Function/Component Selection"

3 Semi-automatic A/C System - Climatic Page 2 / 28 - Select "Body, (Repair Gr. 01, 27, 50 to 97)" - Select "Heating, ventilation, air conditioning system (RG 01; 80-87" - Select "Self-diagnosis" - Select "08-Climatic" - Select "Functions" - Select "On Board Diagnostic (OBD) Functions" Review listed selections and choose as specified or desired. - Follow testers prompts. Heating and A/C system components in passenger compartment, servicing Note: Disconnect battery before removing components marked with ** Repair Manual, Electrical Equipment, Repair Group 27, A data plate indicates the refrigerant used and capacity.

4 Semi-automatic A/C System - Climatic Page 3 / 28 Volkswagen Technical Site: огромный архив документации по автомобилям Volkswagen, Skoda, Seat, Audi Instrument panel ** Center air vents 80-1, Center air vents, removing and installing Right side window defroster air duct In right A-pillar Right air vent 80-1, Right / left air vent, removing and installing Heating and A/C controls -

5 Semi-automatic A/C System - Climatic Page 4 / 28 Climatic With Fresh Air/Recirculating Flap Switch E159 With Rear Window Defogger Switch E230 with Fresh Air Blower Switch E9 With A/C Control Module J301 With Immediate Heating Button E537 where applicable 87-2, Heating and A/C controls, removing and installing Recirculation Flap Motor V113 Checking: Use Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-2, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/ , Recirculation Flap Motor V113, removing and installing Replacing: Initiate Basic Setting using Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-2, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/5052. Right footwell air vent

6 Semi-automatic A/C System - Climatic Page 5 / , Right footwell air vent, removing and installing Fresh Air Blower V2 Depending on unit configuration, blower on vehicle may not be exactly as shown here 80-1, Fresh Air Blower V2, removing and installing Fresh Air Blower Series Resistor With Fuse N24 Depending on unit configuration, resistor with fuse may not be exactly as shown here 80-1, Fresh Air Blower Series Resistor With Fuse N24, removing and installing Heating and ventilation unit partition Removing 80-1, Heating and ventilation unit partition, removing Evaporator Vent Temperature Sensor G , Evaporator Temperature Sensor G308, removing and installing Sealing caps Only in vehicles without air guide to vent installed in center console at rear

7 Semi-automatic A/C System - Climatic Page 6 / 28 Dust and pollen filter With activated charcoal filter 80-1, Dust and pollen filter, removing and installing Center console air duct Connection to center console air guide To remove, center console must be removed Repair Manual, Body Interior, Repair Group 68, Right rear footwell air duct 80-1, Rear footwell air ducts, removing and installing Left rear footwell air duct 80-1, Rear footwell air ducts, removing and installing Screws Qty. 8 Observe varying lengths Heating and A/C control adapter Auxiliary Heater Heating Element Z35 Only on models with Diesel engine 80-1, Auxiliary Heater Heating Element Z35,

8 Semi-automatic A/C System - Climatic Page 7 / 28 removing and installing Heater core 80-1, Heater core, removing and installing Left footwell air vent 80-1, Left footwell air vent, removing and installing Temperature Regulator Flap Motor V68 Checking: Use Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-2, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/ , Temperature Regulator Flap Motor V68, removing and installing Replacing: Initiate Basic Setting using Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-2, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/5052. Air distribution control - flexible cable 87-2, Air distribution control - flexible cable, removing and installing

9 Semi-automatic A/C System - Climatic Page 8 / 28 Footwell Outlet Temperature Sensor G , Footwell Outlet Temperature Sensor G192, removing and installing Heating and A/C unit 87-2, Heating and A/C unit, removing and installing Disassembling and assembling 87-2, Heating and A/C unit, disassembly and assembly Left side window defroster air duct In left A-pillar Center Outlet Temperature Sensor G , Center Outlet Temperature Sensor G191, removing and installing Heating and A/C unit, removing and installing Preparation: Special tools, testers and auxiliary items required

10 Semi-automatic A/C System - Climatic Page 9 / 28 Drip tray for VAS6100 VAS 6208 Hose clamps, up to 40 mm Compressed air gun, commercially available Caution! Switch off all electrical consumers. Switch ignition off and remove ignition key. Note: To improve accessibility, additional components e.g., engine cover must be removed (depending on engine version). - Evacuate refrigerant circuit using refrigerant recycling/recovery unit Kent-Moore ACR4 (or UL approved equivalent)

11 Semi-automatic A/C System - Climatic Page 10 / 28 Repair Manual, Refrigerant R134a - Servicing, Repair Group 00,. Observe notes 87-5, General information. - Remove instrument panel Repair Manual, Body Interior, Repair Group 70, - Remove facing wall in plenum chamber. Repair Manual, Body Exterior, Repair Group 50, - Remove rear footwell air ducts 80-1, Rear footwell air ducts, removing and installing - Place Drip tray for VAS6100 VAS 6208 under engine. - Mark coolant hoses Warning! Scalding danger! The cooling system is pressurized when the engine is warm. Wear gloves and other protection and carefully release system pressure if necessary before performing repairs. - Clamp off coolant hoses using Hose clamps, up to 40 mm and disconnect coolant hoses to heater core.

12 Semi-automatic A/C System - Climatic Page 11 / 28 - Connect a section of hose - A - onto upper connection. - Hold suitable container - B - under lower connection - C -. - Using a compressed air gun, carefully blow residual coolant from heater core at heater core connection. Warning! Frostbite danger! High pressure refrigerant may leak out if refrigerant circuit is not discharged. Always evacuate refrigerant prior to opening refrigerant circuit. - From engine compartment, remove bolts (12 Nm) for refrigerant lines Disconnect refrigerant lines from expansion valve Caution! Always plug open refrigerant line connections to prevent dirt and moisture contamination.

13 Semi-automatic A/C System - Climatic Page 12 / 28 Where applicable, use sealing caps from replacement expansion valve. - Cover floor carpet in vehicle interior with leak-proof foil and absorbent paper. Note : Observe screw position, length and orientation during removal. Screw 4 Nm Screw

14 Semi-automatic A/C System - Climatic Page 13 / 28 Qty. 2 4 Nm Cable bracket Heating and A/C unit Removing: - Disconnect condensation water drain hose from heating and A/C unit 87-3, Heating and A/C unit condensation water drain hose, checking. - Disconnect electrical connections from heating and A/C unit. Note : All cable ties opened or cut during air conditioner removal must be reinstalled at the same locations during installation. The wiring harness air conditioner" is removed together with the air conditioner unit. - Remove screws Item from bracket Item Remove supports Item and Item Remove screws Item and Item and remove bracket Item Remove screws Item and Item from cable bracket Item Note : To be able to reach bolt Item - 1 -, heating and A/C unit on driver side must be pulled out slightly from facing wall.

15 Semi-automatic A/C System - Climatic Page 14 / 28 When removing heat unit, ensure the two coolant pipes of the heater core do not get caught and bent or damaged on plenum chamber or sound insulation pan. Also pay attention to wiring harness, individual wiring connections may get damaged when pulling too forcefully on wiring harness. - Remove heating and A/C unit. Installing: Install in reverse order of removal, noting the following: Note : The assistance of a second mechanic is necessary to install the heating and ventilation unit. - When inserting heating and ventilation unit, have the second mechanic guide both coolant pipes to heater core through the seal (from engine compartment) 87-2, Heating and A/C unit seal at bulkhead, installation position. - When installing, ensure condensation water drain hose is seated correctly 87-3, Heating and A/C unit condensation water drain hose, checking - After installing heater core, replace engine coolant completely (refer to applicable Engine repair manual, Rep. Gr. 19.

16 Semi-automatic A/C System - Climatic Page 15 / 28 Bracket Screws 8 Nm Assembly carrier Right support Left support Screws Qty. 2 8 Nm Bracket Screws Qty. 2 8 Nm Heating and A/C unit seal at bulkhead, installation position Note: Note installation position of seal - A - during assembly. Heating and A/C unit, disassembly and assembly

17 Semi-automatic A/C System - Climatic Page 16 / 28 Temperature Regulator Flap Motor V68 Checking: Use Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-2, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/ , Temperature Regulator Flap Motor V68, removing and installing Replacing: Initiate Basic Setting using Vehicle Diagnostic, Testing and

18 Semi-automatic A/C System - Climatic Page 17 / 28 Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-2, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/5052. Bracket Screws screws must be removed to separate air distribution and evaporator housings. Cover Recirculation Flap Motor V113 Checking: Use Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-2, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/ , Recirculation Flap Motor V113, removing and installing Replacing: Initiate Basic Setting using Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-2, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/5052. Air intake housing With recirculating air flap

19 Semi-automatic A/C System - Climatic Page 18 / 28 Evaporator housing - upper part Disassembly and assembly 87-3, Evaporator housing, disassembly and assembly Evaporator housing - lower part Disassembly and assembly 87-3, Evaporator housing, disassembly and assembly Evaporator 87-5, Evaporator, removing and installing Evaporator Vent Temperature Sensor G , Evaporator Temperature Sensor G308, removing and installing Glove compartment cooling vent Glove compartment cooling hose Fresh Air Blower Series Resistor With Fuse N , Fresh Air Blower Series Resistor With Fuse N24, removing and installing Fresh Air Blower V2 80-1, Fresh Air Blower V2, removing and installing Dust and pollen filter

20 Semi-automatic A/C System - Climatic Page 19 / 28 With activated charcoal filter 80-1, Dust and pollen filter, removing and installing Cover For dust and pollen filter Heater core 80-1, Heater core, removing and installing Heater core trim Auxiliary Heater Heating Element Z35 Only models with Diesel engine 80-1, Auxiliary Heater Heating Element Z35, removing and installing Air distribution housing Heating and A/C controls, removing and installing Removing: Caution! Switch off all electrical consumers. Switch ignition off and remove ignition key. Note: Heating and A/C controls consist of two separable housings. Before removing controls, set rotary control knobs to the following positions: Heater control to "cold"

21 Semi-automatic A/C System - Climatic Page 20 / 28 Blower control to "0" Air flow control to "footwell" - Remove radio. Repair Manual, Communication, Repair Group 91, - Remove long screws and short screws and remove controls from center console. - Disengage electrical connection retainer - A - by pulling in direction of - arrow Disengage electrical connection retainer - B - to connector - arrow 2 - and disconnect electrical connection - C -. - Disengage electrical connection retainer - D - and disconnect electrical connection - D -.

22 Semi-automatic A/C System - Climatic Page 21 / 28 Installing: Install in reverse order of removal, ensuring rotary control knobs have not been moved from the positions as specified for removal. Heating and A/C controls, multi-pin connector assignments Special tools, testers and auxiliary items required adapter cable VAG 1598/47 20-pin electrical connection, T20c 3 - Center Outlet Temperature Sensor G High Pressure Sensor G CAN Bus - Low 8 - CAN Bus - High 12 - Right seat heater (optional - where applicable) 13 - Left seat heater (optional - where applicable) 15 - Terminal 75 seat heater (optional) 16 - A/C Compressor Regulator Valve N Positive - B+ (Terminal 30A) 20 - Ground (GND) - Terminal 31

23 Semi-automatic A/C System - Climatic Page 22 / 28 Volkswagen Technical Site: огромный архив документации по автомобилям Volkswagen, Skoda, Seat, Audi 16-pin electrical connection, in wiring diagram T16e 1 - Temperature Regulator Flap Motor V68, warm 2 - Evaporator Vent Temperature Sensor G Footwell Outlet Temperature Sensor G Temperature Regulator Flap Motor Position Sensor G V for Temperature Regulator Flap Motor Position Sensor G Ground (GND) for Temperature Regulator Flap Motor Position Sensor G92, Center Outlet Temperature Sensor G191, Footwell Outlet Temperature Sensor G192 and Evaporator Vent Temperature Sensor G Recirculation Flap Motor V113, open 10 - Recirculation Flap Motor V113, close 11 - Temperature Regulator Flap Motor V68, cold 5-pin electrical connection, T5 1-3rd blower speed 2-2nd blower speed 3-1st blower speed

24 Semi-automatic A/C System - Climatic Page 23 / th blower speed 5 - Terminal X Air distribution control - flexible cable, removing and installing Removing Caution! Switch off all electrical consumers. Switch ignition off and remove ignition key. - Remove heating and A/C controls 87-2, Heating and A/C controls, removing and installing - Carefully pull out adapter. - Press in retaining tab - arrow - and remove flexible cable. Installing: Install in reverse order of removal, ensuring air distribution rotary control knob has not been moved from the positions as specified for removal. Note: When installing flexible cable, adapter and rotary switches on heating and ventilation controls must be oriented in a specific manner. Checking 87-2, Air distribution control - flexible cable operation, checking Air distribution control - flexible cable operation, checking

25 Semi-automatic A/C System - Climatic Page 24 / 28 Check function of air distribution control flexible cable as follows: - Set fresh air blower to maximum speed. If air flow flows from defroster air vents in the "Defrost" position and no air flows from footwell air vents, installation of flexible cable is correct. If this is not the case, remove flexible cable from adapter. Place Heating and ventilation controls onto adapter and rotate rotary knob for air distribution 1 2 rotation (180 ). Then reconnect flexible cable. Repeat test. Heating and A/C unit condensation water drain hose, checking - Remove front passengers side footwell cover. Note: The condensation water drain hose must be able to be connected to connection of heating and A/C unit without pre-tension. Condensation water drain hose must sit securely on heating and A/C unit. Recirculation Flap Motor V113, removing and installing Removing: Caution! Switch off all electrical consumers. Switch ignition off and remove ignition key. - Remove glove compartment

26 Semi-automatic A/C System - Climatic Page 25 / 28 Repair Manual, Body Interior, Repair Group 68, - Remove cover for flap motors. - Disconnect electrical connection from motor Remove motor Installing: Install in reverse order of removal, noting the following: Note: After installing, check recirculation flap function. Initiate "Basic Setting" function using Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding". Temperature Regulator Flap Motor V68, removing and installing Removing: Caution! Switch off all electrical consumers. Switch ignition off and remove ignition key. - Remove left footwell air vent 80-1, Left footwell air vent, removing and installing - Unclip Data Bus On Board Diagnostic Interface J533 from bracket.

27 Semi-automatic A/C System - Climatic Page 26 / 28 - Remove screws Item , Item and remove bracket Item Remove cover for heater core. - Unhook brace from actuator lever Remove screws and remove motor Installing: Install in reverse order of removal, noting the following. Note: After installing Temperature Regulator Flap Motor V68, check temperature flap function. - Checking: Use Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding". - Replacing: Initiate Basic Setting using Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding". Footwell Outlet Temperature Sensor G192, removing and installing Removing: - Remove instrument panel Repair Manual, Body Interior, Repair Group 70, - Remove screws Item from bracket Item

28 Semi-automatic A/C System - Climatic Page 27 / 28 - Disconnect electrical connection at sensor Press bracket Item lightly toward left, rotate sensor and remove from housing. Installing: Install in reverse order of removal. Center Outlet Temperature Sensor G191, removing and installing Removing: Caution! Switch off all electrical consumers. Switch ignition off and remove ignition key. - Remove left instrument panel cover. Repair Manual, Body Interior, Repair Group 70,

29 Semi-automatic A/C System - Climatic Page 28 / 28 - Disconnect electrical connection at sensor Rotate sensor - 2 -, rotate 90 in direction of - arrow - and remove from instrument panel. Installing: Install in reverse order of removal. Outside Air Temperature Sensor G17, removing and installing Removing: - Remove center air vent from front bumper cover catches. Repair Manual, Body Exterior, Repair Group 63, - Unclip Outside Air Temperature Sensor G from bracket and disconnect electrical connection. Installing: Install in reverse order of removal, noting the following: Note: Ensure electrical connector is seated correctly to prevent water entry.

30 Automatic A/C system - Climatronic Page 1 / Automatic A/C system - Climatronic General information GTI from model year 2006 may be equipped with a dualzone (right / left - front) Climatronic system. Climatronic is a fully automatic, digital-electronic climate control system. The temperature of the interior air supply, fresh air blower speeds and passenger compartment air distribution are regulated automatically. The system features fully digital electronic circuitry and On Board Diagnostic (OBD) capability. In addition to fully automatic function, air distribution settings and fresh air blower speeds can be selected manually to suit individual needs. The Climatronic Control Module J255 is the heart of the system. It receives input information from the integrated A/C control head and various electronic components (sensors and switches). This information is processed by the control module in accordance with specified values and provides corresponding output signals that control electrical components (actuators). The system controls interior air temperature and distribution for the driver and front passenger. The system continually samples and compares the selected interior air temperature with the actual air temperature measured by the system. Blower speeds, air temperature and distribution are then adjusted and regulated accordingly. The A/C control head integrated with -J255- contains all controls and relevant displays needed to operate the Climatronic system. The systems input temperatures are displayed in LCD displays. All automatic or manual function selections are input into the A/C control head via buttons located between and below the LCD displays. When "AUTO" mode is selected, fresh air blower speed and air distribution signals are automatically monitored and adjusted. The fresh air blower speed is high when there is a large difference between the selected temperature and the actual interior temperature, and low when the difference is small or the same. The interior temperature settings speed are indicated on the A/C control head display at all times. The system can be switched on and off by pressing the "OFF" button.

31 Automatic A/C system - Climatronic Page 2 / 46 Manually selected settings remain stored in memory after switching the ignition off and will be recalled on subsequent re-start. Only the function "Air recirculation" is erased after 20 minutes. Note: Pressing AUTO button overrides all manual settings. Climatronic, manual operation Owners Manual In "ECON" operation, A/C compressor output is regulated to almost zero delivery. Heating and A/C operation continues to be controlled electronically. Before troubleshooting or servicing, technicians must be familiar with the functions and operation specifics of the standard or optional A/C system. Always read the owners manual and review applicable system functions. Note: Additional information: Owners Manual Self Study Program - Course Number "VW 2006 GTI Introduction" Wiring Diagrams and Component Locations Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/ Connect VAS 5051/5052 to vehicle Data Link Connector (DLC) - Select operating mode "Guided Fault Finding" - Enter appropriate model, equipment and model year information and press ">" After all control modules have been registered and DTC memories checked, - Press "Go to" - Select "Function/Component Selection" - Select "Body, (Repair Gr. 01, 27, 50 to 97)"

32 Automatic A/C system - Climatronic Page 3 / 46 - Select "Heating, ventilation, air conditioning system (RG 01; 80-87" - Select "Self-diagnosis" - Select "08-Climatronic" - Select "Functions" - Select "On Board Diagnostic (OBD) Functions" Review listed selections and choose as specified or desired. - Follow testers prompts. A/C Control Head E87, display and functions Left selected temperature display Displays selected temperature.

33 Automatic A/C system - Climatronic Page 4 / 46 Changing display value: With Climatronic on, simultaneously press and hold AUTO and ECON buttons to toggle between Fahrenheit to Celsius. Air recirculation button Press to recirculate interior air when outside air quality is poor. Central air distribution button Footwell air distribution button Upper air distribution button Right selected temperature display Displays selected temperature. Changing display value: With Climatronic on, simultaneously press and hold AUTO and ECON buttons to toggle between Fahrenheit to Celsius. Windshield defrost button Rear window defroster button Left temperature regulator Rotate to increase or decrease left front passenger compartment temperature setting. Blower speed regulator Interior temperature sensor Push button OFF Pressing OFF button to switch Climatronic system on or off.

34 Automatic A/C system - Climatronic Page 5 / 46 Push button AUTO Press AUTO button to automatically maintain the selected vehicle interior temperature. The blower speed and the air distribution are controlled automatically. Push button ECON Press ECON button to cause almost zero A/C compressor output. Heating and A/C operation continues to be controlled electronically. Right temperature regulator Rotate to increase or decrease right front passenger compartment temperature setting. Climatronic Control Module J255 with A/C Control Head E87, removing and installing Note: The Climatronic Control Module J255 and A/C Control Head E87 are integrated and cannot be serviced or repaired separately. Removing: Caution! Switch off all electrical consumers. Switch ignition off and remove ignition key. - Remove center instrument panel trim. Repair Manual, Body Interior, Repair Group 68,

35 Automatic A/C system - Climatronic Page 6 / 46 - Remove screws and remove A/C Control Head E from instrument panel. - Disconnect electrical connections from A/C Control Head E87. Installing: Install in reverse order of removal. Climatronic Control Module J255, multi-pin connector assignments Special tools, testers and auxiliary items required Test Box 105 Pin VAG1598/42 adapter cable VAG 1598/47

36 Automatic A/C system - Climatronic Page 7 / pin electrical connection, T20c - A Sunlight Photo Sensor 2 G134 or Sunlight Photo Sensor G107, signal 2 - High Pressure Sensor G Sunlight Photo Sensor 2 G134 or Sunlight Photo Sensor G107, signal 5 - CAN Bus - High 6 - CAN Bus - Low V for Sunlight Photo Sensor 2 G134 or Sunlight Photo Sensor G Plus connection (15a) in vehicles with auxiliary heater 17 - Signal Ground (GND) for sensors 18 - A/C Compressor Regulator Valve N Plus connection (15a); in vehicles with auxiliary heater plus connection (30a) 16-pin electrical connection, T16g -B V for control motors 2 - Left Temperature Flap Potentiometer/Actuator G Right Temperature Flap Potentiometer/Actuator G221

37 Automatic A/C system - Climatronic Page 8 / Defroster Flap Motor Position Sensor G Central Flap Motor Position Sensor G Recirculation Flap Motor Position Sensor G Back Pressure Flap Motor Position Sensor G Left Footwell Vent Temperature Sensor G Right Footwell Vent Temperature Sensor G Fresh Air Intake Duct Temperature Sensor G Evaporator Temperature Sensor G Signal Ground (GND) potentiometer 15 - Left Vent Temperature Sensor G Right Vent Temperature Sensor G pin electrical connection, T16f - C Left Temperature Flap Motor V158, cold 2 - Left Temperature Flap Motor V158, warm 3 - Defroster Flap Motor V107, closed 4 - Defroster Flap Motor V107, open 5 - Central Air Flap Motor V70, upper body outlet 6 - Central Air Flap Motor V70, footwell 7 - Fresh/Recirculating Air Door Motor V154, recirculated air activation 8 - Fresh/Recirculating Air Door Motor V154, fresh air activation 9 - Air Flow Flap Motor V71, open 10 - Air Flow Flap Motor V71, close 11 - Right Temperature Flap Motor V159, cold 12 - Right Temperature Flap Motor V159, warm 15 - Fresh Air Blower V2 (PWM activation)

38 Automatic A/C system - Climatronic Page 9 / Fresh Air Blower V2, return message signal Heating and A/C components in passenger compartment, servicing Note: Disconnect battery before removing components marked with ** Repair Manual, Electrical Equipment, Repair Group 27, A data plate indicates the refrigerant used and capacity. Instrument panel **

39 Automatic A/C system - Climatronic Page 10 / 46 Repair Manual, Body Interior, Repair Group 70, Sunlight Photo Sensor G107 and Sunlight Photo Sensor 2 G134 Checking: Use Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/5052 Function: controls temperature flap and fresh air blow depending on light intensity Emergency running during failure: Climatronic Control Module J255 utilizes a fixed value 87-3, Sunlight Photo Sensor G107 / Sunlight Photo Sensor 2 G134, removing and installing Center air vents 80-1, Center air vents, removing and installing Right side window defroster air duct In right A-pillar Right air vent 80-1, Right / left air vent, removing and installing

40 Automatic A/C system - Climatronic Page 11 / 46 Right Vent Temperature Sensor G151 Checking: Use Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/ , Left Vent Temperature Sensor G150 / Right Vent Temperature Sensor G151, removing and installing Climatronic Control Module J255 The Climatronic Control Module J255 and A/C Control Head E87 are integrated and cannot be serviced or repaired separately. Checking: Use Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/ , Climatronic Control Module J255 with A/C Control Head E87, removing and installing Replacing: Initiate Basic Setting using Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components,

41 Automatic A/C system - Climatronic Page 12 / 46 checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/5052. Air Flow Flap Motor V71 Checking: Use Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/ , Air Flow Flap Motor V71, removing and installing Replacing: Initiate Basic Setting using Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/5052. Fresh/Recirculating Air Door Motor V154 Checking: Use Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/ , Fresh/Recirculating Air Door Motor V154, removing and installing

42 Automatic A/C system - Climatronic Page 13 / 46 Replacing: Initiate Basic Setting using Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/5052. Fresh Air Intake Duct Temperature Sensor G89 Checking: Use Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/5052 Checking: Vehicle Diagnostic, testing info. system VAS 5051/5052 Function: Temperature sensor controls temperature flap and fresh air blower depending on temperature Repair Manual, Body Interior, Repair Group 70, Right footwell air vent 80-1, Right footwell air vent, removing and installing Fresh Air Blower V2 with Fresh Air Blower Control Module J126 Depending on configuration,

43 Automatic A/C system - Climatronic Page 14 / 46 the blower, blower electrical connection and control module on vehicle may not be exactly as shown here Checking: Use Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/ , Fresh Air Blower V2, removing and installing Not applicable Heating and ventilation unit partition Removing 80-1, Heating and ventilation unit partition, removing Sealing caps Only in vehicles without air guide to air vent installed in center console at rear Dust and pollen filter With activated charcoal filter 80-1, Dust and pollen filter, removing and installing Center console air duct Connection to center console air guide To remove, center console must be removed

44 Automatic A/C system - Climatronic Page 15 / 46 Repair Manual, Body Interior, Repair Group 68, Right rear footwell air duct 80-1, Rear footwell air ducts, removing and installing Left rear footwell air duct 80-1, Rear footwell air ducts, removing and installing Evaporator Temperature Sensor G308 Checking: Use Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/ , Evaporator Temperature Sensor G308, removing and installing Right Temperature Flap Motor V159 Checking: Use Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/ , Right Temperature Flap Motor V159, removing

45 Automatic A/C system - Climatronic Page 16 / 46 and installing Replacing: Initiate Basic Setting using Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/5052. Auxiliary Heater Heating Element Z35 Only on models with Diesel engine 80-1, Auxiliary Heater Heating Element Z35, removing and installing Heater core 80-1, Heater core, removing and installing Central Air Flap Motor V70 Checking: Use Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/ , Central Air Flap Motor V70, removing and installing Replacing: Initiate Basic Setting using Vehicle Diagnostic, Testing and Information System VAS

46 Automatic A/C system - Climatronic Page 17 / /5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/5052. Left footwell air vent 80-1, Left footwell air vent, removing and installing Left Temperature Flap Motor V158 Checking: Use Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/ , Left Temperature Flap Motor V158, removing and installing Replacing: Initiate Basic Setting using Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/5052. Left Footwell Vent Temperature Sensor G261 Checking: Use Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating

47 Automatic A/C system - Climatronic Page 18 / 46 mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/ , Left Footwell Vent Temperature Sensor G261, removing and installing Defroster Flap Motor V107 Checking: Use Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/ , Defroster Flap Motor V107, removing and installing Replacing: Initiate Basic Setting using Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/5052. Heating and A/C unit 87-3, Heating and A/C unit, removing and installing Disassembly and assembly 87-3, Heating and A/C unit, disassembly and assembly

48 Automatic A/C system - Climatronic Page 19 / 46 Right Footwell Vent Temperature Sensor G262 Checking: Use Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/ , Right Footwell Vent Temperature Sensor G262, removing and installing Left side window defroster air duct In left A-pillar Left Vent Temperature Sensor G150 Checking: Use Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/ , Left Vent Temperature Sensor G150 / Right Vent Temperature Sensor G151, removing and installing Heating and A/C unit, removing and installing Preparation: Special tools, testers and auxiliary items required

49 Automatic A/C system - Climatronic Page 20 / 46 Drip tray for VAS6100 VAS 6208 Hose clamps, up to 40 mm Compressed air gun, commercially available Caution! Switch off all electrical consumers. Switch ignition off and remove ignition key. Note: To improve accessibility, additional components e.g. engine cover must be removed (depending on engine version). - Evacuate refrigerant circuit using refrigerant recycling/recovery unit Kent-Moore ACR4 (or UL approved equivalent)

50 Automatic A/C system - Climatronic Page 21 / 46 Repair Manual, Refrigerant R134a - Servicing, Repair Group 00,. Observe notes 87-5, General information - Remove instrument panel Repair Manual, Body Interior, Repair Group 70, - Remove facing wall in plenum chamber. Repair Manual, Body Exterior, Repair Group 50, - Remove both rear footwell air ducts 80-1, Rear footwell air ducts, removing and installing - Place Drip tray for VAS6100 VAS 6208 under the engine. - Mark coolant hoses Warning! Scalding danger! The cooling system is pressurized when the engine is warm. Wear gloves and other protection and carefully release system pressure if necessary before performing repairs. - Clamp off coolant hoses using Hose clamps, up to 40 mm and disconnect coolant hoses to heater core.

51 Automatic A/C system - Climatronic Page 22 / 46 - Connect a section of hose - A - onto upper connection. - Hold suitable container - B - under lower connection - C -. - Using a compressed air gun, carefully blow residual coolant from heater core at heater core connection. Warning! Frostbite danger! High pressure refrigerant may leak out if refrigerant circuit is not discharged. Always evacuate refrigerant prior to opening refrigerant circuit. - From the engine compartment, remove bolts (12 Nm) for refrigerant lines Disconnect refrigerant lines from expansion valve Caution! Always plug open refrigerant line connections to prevent dirt and moisture contamination.

52 Automatic A/C system - Climatronic Page 23 / 46 Where applicable, use sealing caps from replacement expansion valve. - Cover floor carpet in vehicle interior with leak-proof foil and absorbent paper. Note : Observe screw position, length and orientation during removal. Screw 4 Nm Screws

53 Automatic A/C system - Climatronic Page 24 / 46 Qty. 2 4 Nm Cable bracket Heating and A/C unit Removing: - Disconnect condensation water drain hose from heating and A/C unit 87-3, Heating and A/C unit condensation water drain hose, checking. - Disconnect electrical connections from heating and A/C unit. Note : All cable ties opened or cut during air conditioner removal must be reinstalled at the same locations during installation. The wiring harness air conditioner" is removed together with the air conditioner unit. - Remove screws Item from bracket Item Remove support Item Remove screws Item and Item and remove bracket Item Remove screws Item and Item from cable bracket Item Note : To be able to reach the bolt Item - 1 -, heating and A/C unit on driver side must be pulled out slightly from facing wall.

54 Automatic A/C system - Climatronic Page 25 / 46 When removing heat unit, ensure the two coolant pipes of the heater core do not get caught and bent or damaged on plenum chamber or sound insulation pan. Also pay attention to wiring harness, individual wiring connections may get damaged when pulling too forcefully on wiring harness. - Remove heating and A/C unit. Installing: Install in reverse order of removal, noting the following: - When installing, note installation position of seal for heating and A/C unit to engine compartment 87-3, Heating and A/C unit seal at bulkhead, installation position - When installing, ensure condensation water drain hose is seated correctly 87-3, Heating and A/C unit condensation water drain hose, checking. - Fill with coolant (refer to applicable engine repair manual, Rep. Gr. 19). Bracket Screws 8 Nm Assembly carrier Right support Left support

55 Automatic A/C system - Climatronic Page 26 / 46 Screws Qty. 2 8 Nm Bracket Screws Qty. 2 8 Nm Heating and A/C unit seal at bulkhead, installation position Note: Note installation position of seal - A - during assembly. Heating and A/C unit, disassembly and assembly

56 Automatic A/C system - Climatronic Page 27 / 46 Volkswagen Technical Site: огромный архив документации по автомобилям Volkswagen, Skoda, Seat, Audi Central Air Flap Motor V70 Checking: Use Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/ , Central Air Flap Motor V70, removing and installing Replacing: Initiate Basic Setting using Vehicle Diagnostic, testing info. system VAS 5051/5052

57 Automatic A/C system - Climatronic Page 28 / , Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/5052. Left Temperature Flap Motor V158 Checking: Use Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/ , Left Temperature Flap Motor V158, removing and installing Replacing: Initiate Basic Setting using Vehicle Diagnostic, testing info. system VAS 5051/ , Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/5052. Defroster Flap Motor V107 Checking: Use Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/ , Defroster Flap Motor V107, removing and installing

58 Automatic A/C system - Climatronic Page 29 / 46 Replacing: Initiate Basic Setting using Vehicle Diagnostic, testing info. system VAS 5051/ , Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/5052. Bracket Screws Remove screws to separate air distribution and evaporator housings. Cover Fresh/Recirculating Air Door Motor V154 Checking: Use Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/ , Fresh/Recirculating Air Door Motor V154, removing and installing Replacing: Initiate Basic Setting using Vehicle Diagnostic, testing info. system VAS 5051/ , Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/5052. Air Flow Flap Motor V71 Checking: Use Vehicle

59 Automatic A/C system - Climatronic Page 30 / 46 Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/ , Air Flow Flap Motor V71, removing and installing Replacing: Initiate Basic Setting using Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/5052. Air intake housing With recirculating air flap (Climatic) With air flow flap (Climatronic) Evaporator housing - upper part Disassembling and assembling evaporator housing 87-3, Evaporator housing, disassembly and assembly Evaporator housing - lower part Disassembling and assembling evaporator housing 87-3, Evaporator housing, disassembly and assembly Evaporator

60 Automatic A/C system - Climatronic Page 31 / , Evaporator, removing and installing Evaporator Temperature Sensor G308 Checking: Use Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/ , Evaporator Temperature Sensor G308, removing and installing Glove compartment cooling vent Glove compartment cooling hose Fresh Air Blower V2 with Fresh Air Blower Series Resistor With Fuse N24 Checking: Use Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/ , Fresh Air Blower V2, removing and installing Dust and pollen filter With activated charcoal filter

61 Automatic A/C system - Climatronic Page 32 / , Dust and pollen filter, removing and installing Cover For dust and pollen filter Heater core 80-1, Heater core, removing and installing Heater core trim Auxiliary Heater Heating Element Z35 Only installed on vehicles with Diesel engine. 80-1, Auxiliary Heater Heating Element Z35, removing and installing Right Temperature Flap Motor V159 Checking: Use Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/ , Right Temperature Flap Motor V159, removing and installing Replacing: Initiate Basic Setting using Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating

62 Automatic A/C system - Climatronic Page 33 / 46 mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/5052. Air distribution housing Evaporator housing, disassembly and assembly - Separate evaporator housing from heating and A/C unit 87-3, Heating and A/C unit, disassembly and assembly. - Disconnect electrical connections from heating and A/C unit. Evaporator housing - lower section Evaporator

63 Automatic A/C system - Climatronic Page 34 / 46 Ensure insulation foam is not damaged 87-5, Evaporator, removing and installing Clip Evaporator housing - lower section Screw Expansion valve / bulkhead seal 87-5, Evaporator, removing and installing Bracket 87-5, Evaporator, removing and installing Left Footwell Vent Temperature Sensor G261, removing and installing Removing: Caution! Switch off all electrical consumers. Switch ignition off and remove ignition key. - Remove instrument panel Repair Manual, Body Interior, Repair Group 70, - Remove screws Item from bracket Item

64 Automatic A/C system - Climatronic Page 35 / 46 - Disconnect electrical connection at sensor Press bracket Item slightly toward left, rotate sensor and remove from housing. Installing: Install in reverse order of removal. Right Footwell Vent Temperature Sensor G262, removing and installing Removing: Caution! Switch off all electrical consumers. Switch ignition off and remove ignition key. Note: Right Footwell Vent Temperature Sensor G262 is depicted with instrument panel removed. It is not necessary to remove instrument panel. - Remove glove compartment Repair Manual, Body Interior, Repair Group 68,

65 Automatic A/C system - Climatronic Page 36 / 46 - Disconnect electrical connection at sensor Rotate sensor and remove from housing. Installing: Install in reverse order of removal. Evaporator Temperature Sensor G308, removing and installing Removing: Caution! Switch off all electrical consumers. Switch ignition off and remove ignition key. - Remove front passengers footwell cover - 1-.

66 Automatic A/C system - Climatronic Page 37 / 46 - Disconnect electrical connection at sensor Rotate sensor in direction of - arrow - and remove. Outside Air Temperature Sensor G17, removing and installing Removing: - Remove center air vent from front bumper cover catches. Repair Manual, Body Exterior, Repair Group 63, - Unclip Outside Air Temperature Sensor G from bracket and disconnect electrical connection. Installing: Install in reverse order of removal, noting the following: Note: Ensure electrical connector is seated correctly to prevent water entry.

67 Automatic A/C system - Climatronic Page 38 / 46 Left Vent Temperature Sensor G150 / Right Vent Temperature Sensor G151, removing and installing Removing: Caution! Switch off all electrical consumers. Switch ignition off and remove ignition key. Note: Removal of sensors on both sides is identical, only the sides are reversed. - Remove cover at left or right on instrument panel. Repair Manual, Body Interior, Repair Group 70, - Disconnect electrical connection from sensor Rotate sensor in direction of - arrow - and remove from instrument panel. Installing: Install in reverse order of removal. Sunlight Photo Sensor G107 / Sunlight Photo Sensor 2 G134, removing and installing Removing:

68 Automatic A/C system - Climatronic Page 39 / 46 - Unclip photo sensor from instrument panel using appropriate tool. - Disconnect electrical connection from sunlight photo sensor. Installing: Install in reverse order of removal. Heating and A/C unit condensation water drain hose, checking - Remove front passengers side footwell cover. Note: Condensation water drain hose must be able to be connected to connection of heating and A/C unit without pre-tension. Condensation water drain hose must sit securely on heating and A/C unit. Fresh/Recirculating Air Door Motor V154, removing and installing

69 Automatic A/C system - Climatronic Page 40 / 46 Removing: Caution! Switch off all electrical consumers. Switch ignition off and remove ignition key. - Remove glove compartment Repair Manual, Body Interior, Repair Group 68, - Remove motor cover. - Disconnect electrical connection from motor Remove motor Installing: Install in reverse order of removal, noting the following. Note: After installing, check motor/flap function. Initiate "Basic Setting" function using Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/5052. Air Flow Flap Motor V71, removing and installing Removing:

70 Automatic A/C system - Climatronic Page 41 / 46 Caution! Switch off all electrical consumers. Switch ignition off and remove ignition key. - Remove glove compartment Repair Manual, Body Interior, Repair Group 68, Note: Position of air flow flap must not be changed. - Remove cover Remove Fresh/Recirculating Air Door Motor V , Fresh/Recirculating Air Door Motor V154, removing and installing. - Disconnect electrical connection from motor Remove motor Installing: Install in reverse order of removal, noting the following. Note: After installing, check motor/flap function. Initiate "Basic Setting" function using Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and

71 Automatic A/C system - Climatronic Page 42 / 46 Information System VAS 5051/5052. Defroster Flap Motor V107, removing and installing Removing: Caution! Switch off all electrical consumers. Switch ignition off and remove ignition key. - Remove drivers storage compartment. Repair Manual, Body Interior, Repair Group 68, - Remove left footwell air vent 80-1, Left footwell air vent, removing and installing. - Remove bracket Item Disconnect electrical connection from motor Remove screws - 1 -, remove motor and unhook brace. Installing: Install in reverse order of removal, noting the following. Note: After installing, check motor/flap function. Initiate "Basic Setting" function using Vehicle

72 Automatic A/C system - Climatronic Page 43 / 46 Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/5052. Left Temperature Flap Motor V158, removing and installing Removing: Caution! Switch off all electrical consumers. Switch ignition off and remove ignition key. - Remove left footwell air vent 80-1, Left footwell air vent, removing and installing. - Remove bracket Item Remove heater core cover. - Disconnect electrical connection from motor Unhook brace from actuator lever Remove screws and remove motor -3-. Installing: Install in reverse order of removal, noting the following. Note: After installing, check motor/flap function. Initiate "Basic Setting" function using Vehicle

73 Automatic A/C system - Climatronic Page 44 / 46 Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/5052. Right Temperature Flap Motor V159, removing and installing Removing: Caution! Switch off all electrical consumers. Switch ignition off and remove ignition key. - Remove glove compartment Repair Manual, Body Interior, Repair Group 68, - Remove right footwell air vent 80-1, Right footwell air vent, removing and installing. - Disconnect electrical connection from Right Temperature Flap Motor V Remove screws and remove motor. - Unhook brace from motor. Installing: Install in reverse order of removal, noting the following. Note:

74 Automatic A/C system - Climatronic Page 45 / 46 After installing, check motor/flap function. Initiate "Basic Setting" function using Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/5052. Central Air Flap Motor V70, removing and installing Removing: Caution! Switch off all electrical consumers. Switch ignition off and remove ignition key. - Remove instrument panel. Repair Manual, Body Interior, Repair Group 70, - Disconnect electrical connection from Central Air Flap Motor V70. - Remove screws and remove motor. Installing: Install in reverse order of removal, noting the following. Note: After installing, check motor/flap function.

75 Automatic A/C system - Climatronic Page 46 / 46 Initiate "Basic Setting" function using Vehicle Diagnostic, Testing and Information System VAS 5051/5052 in operating mode "Guided Fault Finding" 87-3, Components, checking and adjusting with Vehicle Diagnostic, Testing and Information System VAS 5051/5052.

76 A/C Compressor and Bracket Page 1 / A/C Compressor and Bracket A/C compressor and bracket - 2.5L 5-cylinder gasoline engine, assembly Special tools, testers and auxiliary items required Torque wrench 550Nm VAG 1331 (or 5-50 Nm equivalent) Note: The compressor bracket and related components can be removed and installed without having to open the refrigerant circuit. If it is necessary to open the refrigerant circuit, for example when replacing compressor, first extract A/C refrigerant using recycling/recovery unit Kent- Moore ACR4 Repair Manual, Refrigerant R134a - Servicing, Repair Group 00,. Before carrying out any work on the A/C refrigerant system, refer to all CAUTIONS and WARNINGS in A/C refrigerant system safety measures Repair Manual, Refrigerant R134a - Servicing, Repair Group 00,

77 A/C Compressor and Bracket Page 2 / 10 Ribbed belt, removing Repair Manual, 2.5 Liter 5-Cyl. 4V Engine Mechanical, Fuel Injection Ignition, Engine Code(s): BGP, BGQ, Repair Group 13, Observe length of removed bolts and reinstall accordingly. Bracket For Generator (GEN) and A/C compressor Removing without opening refrigerant circuit:

78 A/C Compressor and Bracket Page 3 / 10 - Remove bolts Remove A/C compressor from bracket and secure to body with appropriate material (e.g. welding wire) 87-4, A/C compressor, securing to body - Remove bolts through and remove bracket from engine. Installing: - Install in reverse order of removal, noting the following: - Loosely install and then and torque bolts to specified value. - Route ribbed belt according to diagram 87-4, Ribbed belt, routing Socket head bolt M8x60 25 Nm Socket head bolt M8x Nm Hex socket bolt M8x30 25 Nm 4x A/C compressor 87-5, A/C compressor, removing and installing Hex bolts M8x85 25 Nm

79 A/C Compressor and Bracket Page 4 / 10 Qty. 3 Dowel sleeves Qty. 2 Ensure proper seating between bracket and A/C compressor A/C compressor, securing to body Ribbed belt, routing

80 A/C Compressor and Bracket Page 5 / 10 Upper idler pulley Ribbed belt pulley - generator Lower idler pulley Ribbed belt for generator and coolant pump Ribbed belt pulley - A/C compressor Ribbed belt for A/C compressor Ribbed belt pulley - crankshaft Tensioning roller for ribbed belt for A/C compressor Tensioning roller for ribbed belt for generator and coolant pump Ribbed belt pulley - coolant pump A/C compressor and bracket - 2.0L 4-cylinder TFSI engine, removing and installing Special tools, testers and auxiliary items required Torque Wrench 5-50Nm VAG1331 (or 5-50 Nm equivalent) Note : The compressor bracket and related components can be removed and installed without having to open the refrigerant circuit. If it is necessary to open the refrigerant circuit, for example when replacing compressor, first extract A/C refrigerant using recycling/recovery unit Kent- Moore ACR4 Repair Manual, Refrigerant R134a - Servicing, Repair Group 00,.

81 A/C Compressor and Bracket Page 6 / 10 Before carrying out any work on the A/C refrigerant system, refer to all CAUTIONS and WARNINGS in A/C refrigerant system safety measures Repair Manual, Refrigerant R134a - Servicing, Repair Group 00, Ribbed belt, removing Repair Manual, 2.0 Liter 4-Cyl. 4V Turbo Engine Mechanical, Fuel Injection Ignition, Engine Code(s): BPY, Repair Group 13, Observe length of removed bolts and reinstall accordingly.

82 A/C Compressor and Bracket Page 7 / 10 Hex socket bolt M10 45 Alignment bore 40 Nm Hex socket bolt M Nm Hex socket bolt M Nm Hex socket bolt M Nm A/C compressor

83 A/C Compressor and Bracket Page 8 / , A/C compressor, removing and installing Hex bolts M x 25 Nm Hex socket bolt M10 45 Alignment bore 40 Nm Hex socket bolt M Nm Dowel sleeves 2x Ensure proper seating between auxiliary component bracket and A/C compressor Bracket For Generator (GEN) and A/C compressor Removing without opening refrigerant circuit: - Remove generator Repair Manual, Electrical Equipment, Repair Group 27, - Remove bolts Remove A/C compressor from bracket and secure to body with appropriate material (e.g. welding wire) 87-4, A/C compressor,

84 A/C Compressor and Bracket Page 9 / 10 securing to body - Remove bolts to and and and remove bracket from engine. Installing - Install in reverse order of removal, noting the following: - Loosely install all bolts and then tighten in the following sequence: - 1 -, - 7 -, - 4 -, - 8 -, and Torque bolts to specified value. - Route ribbed belt according to diagram 87-4, Ribbed belt, routing A/C compressor, securing to body

85 A/C Compressor and Bracket Page 10 / 10 Ribbed belt, routing Tensioner roller Ribbed belt pulley - generator Ribbed belt pulley - A/C compressor Ribbed belt Ribbed belt pulley - crankshaft

86 A/C Refrigerant System, servicing Page 1 / A/C Refrigerant System, servicing General information Note: General A/C refrigerant system servicing procedures (e.g., component/system descriptions, extracting refrigerant, recharging, leak detection, troubleshooting etc.), repair and special tool information Repair Manual, Refrigerant R134a - Servicing, Repair Group 00, Before carrying out any work on the A/C refrigerant system, refer to all CAUTIONS and WARNINGS in A/C refrigerant system safety measures Repair Manual, Refrigerant R134a - Servicing, Repair Group 00, Evacuate refrigerant circuit using refrigerant recycling/recovery unit Kent-Moore ACR4 (or UL approved equivalent) Repair Manual, Refrigerant R134a - Servicing, Repair Group 00, Always plug open refrigerant line connections to prevent dirt and moisture contamination. Color coding of O-rings for the R134a refrigerant circuits has been discontinued. Both colored and black O-rings are used. Threaded connections of refrigerant circuit must be coated with polyethylene glycol (PEG) VW material

87 A/C Refrigerant System, servicing Page 2 / 20 no before installing. Under certain conditions, fluid reservoir with dryer cartridge does not require replacement after the refrigerant circuit is opened. To confirm Repair Manual, Refrigerant R134a - Servicing, Repair Group 00, Additional information: Electrical Wiring Diagrams, Troubleshooting and Component Locations binder A/C refrigerant system components, servicing Warning! Frostbite danger! High pressure refrigerant may leak out if refrigerant circuit is not discharged. Always evacuate refrigerant prior to opening refrigerant circuit.

88 A/C Refrigerant System, servicing Page 3 / 20 Fluid reservoir with dryer cartridge 87-5, Fluid reservoir with dryer cartridge, removing and installing A/C compressor 87-5, A/C compressor, removing and installing Observe notes for installing A/C compressor 87-5, A/C compressor, procedure after installation Condenser

89 A/C Refrigerant System, servicing Page 4 / , Condenser, removing and installing High Pressure Sensor G65 Removing and installing 87-5,, removing and installing Bracket High pressure service valve Capacities 87-6, A/C Refrigerant System, capacities Bracket Low pressure service valve Capacities 87-6, A/C Refrigerant System, capacities Expansion valve Servicing function 87-5, Expansion valve, servicing function Hex nut 20 Nm Bracket

90 A/C Refrigerant System, servicing Page 5 / 20 High Pressure Sensor G65, removing and installing - Remove lower noise insulation (under engine). Repair Manual, Body Exterior, Repair Group 50, - Disconnect electrical connection from high pressure sensor Remove sensor from connection of refrigerant line. Note: Replace O-ring Depending on engine version, sensor may be installed on a different side in the vicinity of the condenser. Fluid reservoir with dryer cartridge, removing and installing Note: Observe notes 87-5, General information Removing: Caution! Switch off all electrical consumers. Switch ignition off and remove ignition key. - Evacuate refrigerant circuit using refrigerant recycling/recovery unit Kent-Moore ACR4 (or UL approved equivalent) Repair Manual, Refrigerant R134a - Servicing, Repair Group 00,.

91 A/C Refrigerant System, servicing Page 6 / 20 - Bring lock carrier into service position Repair Manual, Body Exterior, Repair Group 50, - Remove screws - arrows -. - Hang radiator assembly on Shop crane - load cap = kg VAS 6100 and engine sling 2024A using workshop equipment (cable ties or welding wire) and unhook cooler from lock carrier, coolant hoses and refrigerant lines remain connected. - Remove bolt and remove retaining clip. Warning! Frostbite danger! High pressure refrigerant may leak out if refrigerant circuit is not discharged. Always evacuate refrigerant prior to opening refrigerant circuit.

92 A/C Refrigerant System, servicing Page 7 / 20 - Remove screws and pull fluid reservoir with dryer cartridge upward and out. Note: Depending on radiator assembly, there may be only one screw present. Installing: Install in reverse order of removal, noting the following: Note: First tighten screw(s) to 4.2 Nm 0.7 Nm and then bolt When installing radiator assembly, ensure that sealing strips are seated correctly on radiator etc.. A/C compressor, removing and installing Note: Observe notes 87-5, General information Removing: Caution! Switch off all electrical consumers. Switch ignition off and remove ignition key. - Evacuate refrigerant circuit using refrigerant recycling/recovery unit Kent-Moore ACR4 (or UL approved equivalent) Repair Manual, Refrigerant R134a - Servicing, Repair Group 00,. - Remove ribbed belt as applicable: Remove ribbed belt on 2.0L TFSI engine

93 A/C Refrigerant System, servicing Page 8 / 20 Repair Manual, 2.0 Liter 4-Cyl. 4V Turbo Engine Mechanical, Fuel Injection Ignition, Engine Code(s): BPY, Repair Group 13, Remove ribbed belt on 2.5L gasoline engine Repair Manual, 2.5 Liter 5-Cyl. 4V Engine Mechanical, Fuel Injection Ignition, Engine Code(s): BGP, BGQ, Repair Group 13, - Remove noise insulation beneath engine

94 A/C Refrigerant System, servicing Page 9 / 20 Repair Manual, Body Exterior, Repair Group 50,. Warning! Frostbite danger! High pressure refrigerant may leak out if refrigerant circuit is not discharged. Always evacuate refrigerant prior to opening refrigerant circuit. - Remove bolts (22 Nm 1 Nm) from A/C compressor and disconnect refrigerant lines from A/C compressor. - Remove hex screws (25 Nm) and remove A/C compressor. Installing: - Install in reverse order of removal, noting the following: Note: Ensure alignment bushings are seated correctly. Prior to operating compressor after installation, observe notes 87-5, A/C compressor, procedure after installation A/C compressor - pressure relief valve, checking Function: protects refrigerant circuit against excessive pressures Warning! Frostbite danger! Excessive refrigerant outlet pressures are

95 A/C Refrigerant System, servicing Page 10 / 20 vented by the pressure relief valve with considerable force. Should relief valve operate, stay clear of venting refrigerant and switch off engine. A/C compressor pressure relief valve - Sanden, checking Evidence of refrigerant oil in the area of the relief valve - arrow - indicates valve has operated. Replace valve and determine cause of excessive refrigerant system pressure. A/C compressor pressure relief valve - Denso, checking Evidence of refrigerant oil in the area of the relief valve - arrow - indicates valve has operated.

96 A/C Refrigerant System, servicing Page 11 / 20 Volkswagen Technical Site: огромный архив документации по автомобилям Volkswagen, Skoda, Seat, Audi Replace valve and determine cause of excessive refrigerant system pressure. Expansion valve, servicing function Expansion valve, servicing Note: Observe notes 87-5, General information Bolts 12 Nm Qty. 2 Refrigerant lines on expansion valve

97 A/C Refrigerant System, servicing Page 12 / 20 O-ring 13.7 mm; 2.5 mm Expansion valve Removing: - Evacuate refrigerant circuit using refrigerant recycling/recovery unit Kent-Moore ACR4 (or UL approved equivalent) Repair Manual, Refrigerant R134a - Servicing, Repair Group 00,. Warning! Frostbite danger! High pressure refrigerant may leak out if refrigerant circuit is not discharged. Always evacuate refrigerant prior to opening refrigerant circuit. - Remove bolts Item and disconnect refrigerant lines Item from expansion valve. - Remove bolts Item and remove expansion valve. Installing: - Install in reverse order of removal, noting the following: - Charge refrigerant circuit using refrigerant recycling/recovery unit Kent-Moore ACR4 (or UL

98 A/C Refrigerant System, servicing Page 13 / 20 approved equivalent) Repair Manual, Refrigerant R134a - Servicing, Repair Group 00,. Capacities 87-6, A/C Refrigerant System, capacities O-ring 14 mm; 1.82 mm Coat with refrigerant oil when installing O-ring 10.8 mm; 1.82 mm Coat with refrigerant oil when installing O-ring 9.5 mm; 2.5 mm Combination bolt 5 Nm Expansion valve, function The expansion valve restricts and controls refrigerant flow to the evaporator thus lowering refrigerant temperature and pressure. Evaporator, removing and installing Removing: - Remove heating and A/C unit: Climatic system 87-2, Heating and A/C unit,

99 A/C Refrigerant System, servicing Page 14 / 20 removing and installing Climatronic system 87-3, Heating and A/C unit, removing and installing - Disassemble heating and A/C unit: Climatic system 87-2, Heating and A/C unit, disassembly and assembly Climatronic system 87-3, Heating and A/C unit, disassembly and assembly - Disassemble evaporator housing 87-3, Evaporator housing, disassembly and assembly - Remove evaporator - A - from lower section of evaporator housing. Installing: - Install in reverse order of removal, noting the following: Note: Before inserting evaporator, check condensation water drain hose and clean drain if necessary. Before inserting evaporator, clean evaporator housing and evaporator if necessary.

100 A/C Refrigerant System, servicing Page 15 / 20 - When inserting evaporator - A - into lower section of evaporator housing and when assembling both housing halves, ensure foam seal - F - is not damaged. - Check seal - F - (it must be glued all around) before inserting evaporator. - Place bracket - C - and seal / insulation - B - onto connecting pipes of evaporator - D - and - E-. - Insert evaporator - A - into lower section of evaporator housing as shown in the illustration. Note: After assembling both housing halves, check seal / insulation - B - for correct seating at pass-through for both refrigerant lines - D - and - E -. Check seating of bracket - C - on both refrigerant lines - D - and - E - for correct seating. If heat protection insulation - B - is missing or not installed correctly, it can cause reduced performance of the A/C system (change of adjusted control characteristics of expansion valve due to radiant heat). Condenser, removing and installing Note: Observe notes 87-5, General information Removing: Caution!

A/C components, passenger compartment

A/C components, passenger compartment Page 1 of 53 87-68 A/C components passenger compartmen Notes: Upon completion of any A/C system repairs, always check erase the Diagnostic Trouble Code (DTC) memory (scan tool function 02), perform basic

More information

Volkswagen Phaeton 43-2

Volkswagen Phaeton 43-2 Стр. 1 из 27 Volkswagen Phaeton 43-2 Self-leveling suspension, servicing Troubleshooting of air spring struts and level control system Condition Verification Possible causes Corrective action Very slow

More information

Climate control components in passenger compartment, servicing

Climate control components in passenger compartment, servicing Page 1 of 34 87-120 Climate control components in passenger compartment, servicing Component electrical testing page 01-115. A/C control head -E87-, removing and installing Notes: Always check DTC memory

More information

Before disconnecting battery Ground (GND) strap obtain security code for radio with antitheft

Before disconnecting battery Ground (GND) strap obtain security code for radio with antitheft Page 1 of 14 Volkswagen > New Beetle > 1998-2005 Body Interior 70 - Interior trim Instrument panel, removing and installing WARNING! Disconnect battery Ground (GND) strap before working on electrical system,

More information

Volkswagen > Golf, Jetta, GTI, Cabrio > Heating Air Conditioning 87 - A/C controls and mechanical components, servicing

Volkswagen > Golf, Jetta, GTI, Cabrio > Heating Air Conditioning 87 - A/C controls and mechanical components, servicing x-ebahn:///c:/program%20files/ebahn/data/vw-a-a3-h28ebn/vw/a/a3/repair%20ma Page 1 of 13 Volkswagen > Golf, Jetta, GTI, Cabrio > 1993-2002 Heating Air Conditioning 87 - A/C controls and mechanical components,

More information

3.3 Air Conditioning (A/C) Model 202

3.3 Air Conditioning (A/C) Model 202 Notes for Diagnosis The A/C pushbutton control module (N22) has DTC memory and data output.the diagnostic trouble codes and data are displayed via the temperature display window (arrow). The stored DTC

More information

VENTILATION SYSTEM SECTION VTL CONTENTS VENTILATION, HEATER & AIR CONDITIONER VTL-1 PRECAUTION... 2 PREPARATION... 4 FUNCTION DIAGNOSIS...

VENTILATION SYSTEM SECTION VTL CONTENTS VENTILATION, HEATER & AIR CONDITIONER VTL-1 PRECAUTION... 2 PREPARATION... 4 FUNCTION DIAGNOSIS... VENTILATION, HEATER & AIR CONDITIONER SECTION VTL A VENTILATION SYSTEM B C D CONTENTS E PRECAUTION... 2 PRECAUTIONS... 2 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TEN-

More information

Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical 19 Engine-Cooling system (Page GR-19)

Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical 19 Engine-Cooling system (Page GR-19) 19 Engine-Cooling system (Page GR-19) Cooling system components, removing and installing Continued coolant circulation pump (V51), checking Coolant hose connection diagram Coolant pump, removing and installing

More information

3.10 Air Conditioning (A/C) Contents

3.10 Air Conditioning (A/C) Contents 3.10 Air Conditioning (A/C) Contents 3.10 Model 208 as of M.Y. 1998 Diagnosis Page Function Test................................... 11/1 Reading Actual Values............................ 12/1 Version Code...................................

More information

Manual A/C System Components in Engine Compartment, Servicing

Manual A/C System Components in Engine Compartment, Servicing Page 1 of 5 Volkswagen > A4 > 1999-2006 Heating, Ventilation and Air Conditioning 87 - Manual A/C System Manual A/C System Components in Engine Compartment, Servicing CAUTION! Before beginning repairs:

More information

1. SPECIFICATIONS 01-2

1. SPECIFICATIONS 01-2 01-2 1. SPECIFICATIONS Description Specification Heater Core size (mm²) 200 x 165.5 x 25 Capacity (kcal/h) 4,700 Evaporator Core size (mm²) 254.8 x 196.7 x 60 Capacity (kcal/h) 4,700 Blower Supplied power

More information

Module 4: Climate Control

Module 4: Climate Control ÂÂ ÂÂ Air-Conditioning Electronic Control Unit (ECU) Â Controlling Cabin Air Temperature Servo Motors Electric Servo Motors ÂÂ Air-Conditioning Electronic Control Unit (ECU) Automatic Climate Control Sensors

More information

Volkswagen Golf > VW Rabbit GTI 2006-> (A5)

Volkswagen Golf > VW Rabbit GTI 2006-> (A5) Volkswagen Golf 5 2004-> VW Rabbit GTI 2006-> (A5) Allocation of PR. No. for brakes The brake system installed in a vehicle is documented on the vehicle data sticker via the relevant PR number. Example

More information

Engine, removing and installing

Engine, removing and installing Стр 1 из 16 10-1 Engine, removing and installing Special tools, testers and auxiliary items required Torque wrench VAG 1331 Torque wrench VAG 1332 Engine/transmission jack VAG 1383 A Spring type clip pliers

More information

Removing and installing the dash panel

Removing and installing the dash panel Стр. 1 из 6 Removing and installing the dash panel Removing: WARNING Disconnect battery earth strap Electrical System Rep. Gr.27. Removing the centre console Chapter. Remove the steering wheel Chapter.

More information

Motronic injection system,

Motronic injection system, Page 1 of 78 24-1 Motronic injection system, servicing Safety precautions If special testing equipment is required during road test, note the following: WARNING! Scan tools and testing devices must always

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. AIR CONDITIONER CIVIC 2- AND 4-DOOR AII 24158 Issue Date SEP 2002 What s New The installation instructions for the 2003 Civic A/C are the

More information

Program IV: ProStar TM. Performance A/C International. Series. Study Guide Performance A/C Program IV: International ProStar Series TMT

Program IV: ProStar TM. Performance A/C International. Series. Study Guide Performance A/C Program IV: International ProStar Series TMT Performance A/C International A N AV I S TA R C O M PA N Y Program IV: ProStar TM Study Guide TMT-160701 Series Study Guide Performance A/C Program IV: International ProStar Series TMT-160701 2007 International

More information

3.5 Air Conditioning (A/C) Contents

3.5 Air Conditioning (A/C) Contents 3.5 Air Conditioning (A/C) Contents 3.5 Model 210 Diagnosis Page Function Test................................... 11/1 Reading Actual Values............................ 12/1 Individual Flap Test...............................

More information

EVAP system, servicing

EVAP system, servicing Page 1 of 65 20-130 EVAP system, servicing EVAP system components 1 - Cap nut 10 Nm 2 - Cover 3 - Stud For EVAP canister 15 Nm 4 - Sealing piece 5 - Bleed line To EVAP canister purge regulator valve -

More information

Secondary air system. Secondary air system, function/components

Secondary air system. Secondary air system, function/components Page 1 of 26 26-41 Secondary air system Secondary air system, function/components The secondary air system permits faster warm-up and thus makes the catalytic converter ready for operation sooner after

More information

DIAGNOSIS AND TESTING

DIAGNOSIS AND TESTING 412-00-1 Climate Control System - General Information 412-00-1 DIAGNOSIS AND TESTING Climate Control System Refer to Wiring Diagrams Cell 54, Air Conditioner/Heater for schematic and connector information.

More information

3.6 Air Conditioning (A/C) Contents

3.6 Air Conditioning (A/C) Contents 3.6 Air Conditioning (A/C) Contents 3.6 Model 140 as of MY 1996 Page Diagnosis Function Test.................................. 11/1 Reading Sensor Values........................... 12/1 Individual Flap

More information

1996 AUTOMATIC A/C-HEATER SYSTEMS Acura Automatic A/C Systems

1996 AUTOMATIC A/C-HEATER SYSTEMS Acura Automatic A/C Systems Article Text Saturday, January 23, 1999 06:32PM ARTICLE BEGINNING 1996 AUTOMATIC A/C-HEATER SYSTEMS Acura Automatic A/C Systems A4 * PLEASE READ THIS FIRST * WARNING: To avoid injury from accidental air

More information

SECTION Climate Control System - General Information

SECTION Climate Control System - General Information 412-00-i Climate Control System - General Information 412-00-i SECTION 412-00 Climate Control System - General Information CONTENTS PAGE DIAGNOSIS AND TESTING Climate Control System... 412-00-2 Inspection

More information

Headlamps. Стр. 1 из 34. Headlamps from two different manufacturers may be installed: Hella. Valeo

Headlamps. Стр. 1 из 34. Headlamps from two different manufacturers may be installed: Hella. Valeo Volkswagen Passat B6 2005 - Headlamps Стр 1 из 34 94-1 Headlamps General information Headlamps from two different manufacturers may be installed: Hella Valeo With the exception of the various bulb mountings,

More information

Front seats. j a t CAUTION! Before beginning repairs on the electrical system: Obtain the anti-theft radio security code. Switch the ignition off.

Front seats. j a t CAUTION! Before beginning repairs on the electrical system: Obtain the anti-theft radio security code. Switch the ignition off. j a t Front seats 72-1 CAUTION! Before beginning repairs on the electrical system: Obtain the anti-theft radio security code. Switch the ignition off. Search Advanced Search Disconnect the battery Ground

More information

DESCRIPTION AND OPERATION

DESCRIPTION AND OPERATION Page 1 of 10 DESCRIPTION AND OPERATION AIR DELIVERY DESCRIPTION AND OPERATION The air delivery description and operation is divided into five areas: HVAC Control Components Air Speed Air Delivery Recirculation

More information

Drained coolant must be stored in a clean container for disposal or reuse.

Drained coolant must be stored in a clean container for disposal or reuse. Cooling System, Draining and Filling Special tools, testers and auxiliary items required Adapter (V.A.G 1274/8) Adapter V.A.G 1274 tester (V.A.G 1274/10) Hose clamp pliers (V.A.G 1921) Cooling system charge

More information

PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1969 CHEVROLET CAMARO/ FIREBIRD NOTE: INSTRUCTIONS DEPICT CAMARO

PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1969 CHEVROLET CAMARO/ FIREBIRD NOTE: INSTRUCTIONS DEPICT CAMARO specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1969 CHEVROLET CAMARO/ FIREBIRD NOTE: INSTRUCTIONS DEPICT CAMARO CONTROL & OPERATING

More information

Turbocharger system. Note: Observe rules of cleanliness Page Charge air pressure control connection diagram Page 21-2.

Turbocharger system. Note: Observe rules of cleanliness Page Charge air pressure control connection diagram Page 21-2. Page 1 of 50 21-1 Turbocharger system Note: Observe rules of cleanliness Page 21-22. Charge air pressure control connection diagram Page 21-2. All hose connections are secured with hose clamps: parts catalog.

More information

ARTICLE BEGINNING * PLEASE READ THIS FIRST * DESCRIPTION OPERATION ATC COMPUTER BLEND-AIR DOOR ACTUATOR CONTROL PANEL

ARTICLE BEGINNING * PLEASE READ THIS FIRST * DESCRIPTION OPERATION ATC COMPUTER BLEND-AIR DOOR ACTUATOR CONTROL PANEL A/C-HEATER SYSTEM - AUTOMATIC Article Text 1989 Chrysler LeBaron Sedan For m m m m m Copyright 1998 Mitchell Repair Information Company, LLC Thursday, July 03, 2003 10:15AM ARTICLE BEGINNING 1989 AUTOMATIC

More information

2002 Taurus/Sable Workshop Manual

2002 Taurus/Sable Workshop Manual Page 1 of 69 SECTION 412-00: Climate Control System - General Information 2002 Taurus/Sable Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 02/05/2005 Climate Control System Refer to Wiring

More information

3.2 Air Conditioning (A/C) Model 140 up to M.Y. 1995

3.2 Air Conditioning (A/C) Model 140 up to M.Y. 1995 Diagnosis Memory P83-3271-13B Notes for Diagnosis The A/C pushbutton control module (N22) has DTC memory and the capability to display the codes via the temperature display windows (arrows) on the A/C

More information

PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST FORD FAIRLANE & CROWN VICTORIA

PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST FORD FAIRLANE & CROWN VICTORIA PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1955-56 FORD FAIRLANE & CROWN VICTORIA CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect Fit system, offer complete comfort capabilities in virtually

More information

Cooling system components, removing and installing

Cooling system components, removing and installing 19-1 Cooling system components, removing and installing Note: When the engine is warm the cooling system is under pressure. If necessary release pressure before starting repair work. Hoses are secured

More information

A/C-HEATER SYSTEM - AUTOMATIC

A/C-HEATER SYSTEM - AUTOMATIC A/C-HEATER SYSTEM - AUTOMATIC 1996 Subaru SVX 1995-96 AUTOMATIC A/C-HEATER SYSTEMS Subaru SVX * PLEASE READ THIS FIRST * WARNING: To avoid injury from accidental air bag deployment, read and carefully

More information

HEATER, AIR CONDITIONER AND VENTILATION

HEATER, AIR CONDITIONER AND VENTILATION 55-1 HEATER, AIR CONDITIONER AND VENTILATION CONTENTS HEATER AND MANUAL AIR CONDITIONER...................... 3 GENERAL............................... 3 Outline of Change......................... 3 SERVICE

More information

1997 Volkswagen Jetta GT AUTOMATIC TRANSMISSIONS' 'Servicing - Volkswagen AUTOMATIC TRANSMISSIONS. Servicing - Volkswagen

1997 Volkswagen Jetta GT AUTOMATIC TRANSMISSIONS' 'Servicing - Volkswagen AUTOMATIC TRANSMISSIONS. Servicing - Volkswagen 1997-98 AUTOMATIC TRANSMISSIONS Servicing - Volkswagen APPLICATION TRANSAXLE APPLICATION Application Transaxle Model 1997 Golf, GTI, Jetta & Passat 01M 1998 Jetta, Golf, GTI 01M LUBRICATION CHECKING FLUID

More information

3.1 Air Conditioning (A/C) Contents

3.1 Air Conditioning (A/C) Contents 3.1 Air Conditioning (A/C) Contents 3.1 Model 129 up to M.Y. 1997 Diagnosis Page Diagnostic Trouble Code (DTC) Memory................ 11/1 Complaint Related Diagnostic Chart................... 12/1 Electrical

More information

RETRIEVING DIAGNOSTIC TROUBLE CODES

RETRIEVING DIAGNOSTIC TROUBLE CODES Page 1 of 13 SELF-DIAGNOSTICS A/C-heater control assembly monitors system circuits and stores a code in memory if a problem is detected. All codes are stored in memory except Code 2 Malfunction is current

More information

Page 1 of 50 Section 412-00: Climate Control System General Information DIAGSIS AND TESTING 1997 Mark VIII Workshop Manual Climate Control System Special Service Tool(s) 73 Digital Multimeter 105-R0051

More information

A/C-HEATER SYSTEM - AUTOMATIC

A/C-HEATER SYSTEM - AUTOMATIC A/C-HEATER SYSTEM - AUTOMATIC 1994 Volvo 960 1994 Auto. A/C-Heater System Volvo 960 A/C SYSTEM SPECIFICATIONS AUTOMATIC A/C SYSTEM SPECIFICATIONS TABLE Application Specification Compressor Type... Sanden

More information

DESCRIPTION & OPERATION

DESCRIPTION & OPERATION DESCRIPTION & OPERATION HEATER SYSTEM 1997 Heater System WARNING: To avoid injury from accidental air bag deployment, read and follow all SERVICE PRECAUTIONS and DISABLING & ACTIVATING AIR BAG SYSTEM procedures

More information

Cooling system components, removing and installing

Cooling system components, removing and installing Page 1 of 40 19-1 Cooling system components, removing and installing WARNING! The cooling system is pressurized when the engine is warm. When opening the expansion tank, wear gloves and other appropriate

More information

1. DO NOT HANDLE REFRIGERANT IN AN ENCLOSED AREA OR NEAR AN OPEN FLAME

1. DO NOT HANDLE REFRIGERANT IN AN ENCLOSED AREA OR NEAR AN OPEN FLAME 2006 Toyota 4Runner 4.0L Eng Limited 1Search AIR CONDITIONER REQUESTED INFORMATION PRECAUTION 1. DO NOT HANDLE REFRIGERANT IN AN ENCLOSED AREA OR NEAR AN OPEN FLAME 2. ALWAYS WEAR EYE PROTECTION Fig 1:

More information

1988 Chrysler LEBARON

1988 Chrysler LEBARON 1988 Chrysler LEBARON Submodel: Engine Type: L4 Liters: 2.5 Fuel Delivery: FI Fuel: GAS CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by the ethylene glycol antifreeze,

More information

2001 Dodge Caravan Sport MANUAL A/C-HEATER SYSTEMS Caravan, Town & Country, & Voyager

2001 Dodge Caravan Sport MANUAL A/C-HEATER SYSTEMS Caravan, Town & Country, & Voyager SPECIFICATIONS NOTE: Information for Caravan includes the Grand Caravan. SPECIFICATIONS Application Specification Compressor Type Nippondenso 10S20H Compressor Belt Tension (1) System Oil Capacity (2)

More information

Page 1 of 54 412-00 Climate Control System General Information and Diagnostics 2006 Crown Victoria/Grand Marquis DIAGNOSIS AND TESTING Procedure revision date: 12/23/2008 Climate Control System Printable

More information

DESCRIPTION AND OPERATION

DESCRIPTION AND OPERATION Your Current Vehicle: 1998 Ford Explorer Top / Heating, Ventilation, & Air Conditioning / Control Components / DESCRIPTION AND OPERATION DESCRIPTION AND OPERATION SECTION 412-04: Control Components 1998

More information

211 Climate Control 219 PP HVAC (TWK)

211 Climate Control 219 PP HVAC (TWK) 211 Climate Control 219 PP HVAC (TWK) 8-30-02 1 These technical training materials are current as of the date noted on the materials, and may be revised or updated without notice. Always check for revised

More information

1. Disconnect the battery. This is important! This will prevent air bag deployment.

1. Disconnect the battery. This is important! This will prevent air bag deployment. PARTS PACKING LIST Evaporator assembly Drain tube Plastic air plug Hardware package 11040 3601 W. Clarendon Phoenix, Arizona 85019 (602) 233-0090 800-648-4475 www.ackits.com 2003-4 Jeep Wrangler EVAPORATOR

More information

PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST MUSTANG

PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST MUSTANG specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1969-70 MUSTANG CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect

More information

1993 ENGINE PERFORMANCE Volkswagen Self-Diagnostics. EuroVan

1993 ENGINE PERFORMANCE Volkswagen Self-Diagnostics. EuroVan Article Text Saturday, March 18, 2000 10:32PM ARTICLE BEGINNING 1993 ENGINE PERFORMANCE Volkswagen Self-Diagnostics EuroVan INTRODUCTION If no faults were found while performing preliminary inspection

More information

A/C-HEATER SYSTEM - AUTOMATIC

A/C-HEATER SYSTEM - AUTOMATIC A/C-HEATER SYSTEM - AUTOMATIC 1988 Toyota Celica 1988 Automatic A/C-Heater Systems Celica * PLEASE READ THIS FIRST * CAUTION: When discharging air conditioning system, use only approved refrigerant recovery/recycling

More information

Passenger s Side Airbag, On Board Diagnostic (OBD) Service

Passenger s Side Airbag, On Board Diagnostic (OBD) Service Subject: Model(s): Passenger s Side Airbag, On Board Diagnostic (OBD) All 2000 Group: Number: Date: 01 00 03 Apr. 24, 2000 Supersedes T.B. group 01 number 99 21 dated Dec. 8, 1999 Black revision bars indicate

More information

The steering column is only available as a complete unit, without steering lock housing, as a replacement part.

The steering column is only available as a complete unit, without steering lock housing, as a replacement part. Page 1 of 17 Volkswagen > New Beetle > 1998-2005 Suspension, wheels, steering 48 - Steering column Steering column, removing and installing Special tools, testers and auxiliary items required Torque wrench

More information

& 76 CHEVROLET NOVA HEATER ONLY

& 76 CHEVROLET NOVA HEATER ONLY specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic hi l PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1969-74 & 76 CHEVROLET NOVA HEATER ONLY CONTROL & OPERATING INSTRUCTIONS The controls on

More information

AIR CONDITIONER SECTION AC CONTENTS AUTO

AIR CONDITIONER SECTION AC CONTENTS AUTO AIR CONDITIONER SECTION AC CONTENTS AUTO PRECAUTIONS AND PREPARATION SRS Airbag Pretensioner Seatbelt... 4 A/C Refrigerant HFC134a Handling... 4 Compressor Oil... 4 Tube Connection... 4 O-Ring Part Number...

More information

ARTICLE BEGINNING SERVICE PRECAUTIONS

ARTICLE BEGINNING SERVICE PRECAUTIONS Page 1 of 96 ARTICLE BEGINNING SERVICE PRECAUTIONS WARNING: WARNING: CAUTION: When performing any inspection or service procedure on this vehicle, ensure following service precautions are followed to prevent

More information

Audi > Q7 > Electrical Equipment 27 - Removal and Installation. Battery. Special tools, testers and auxiliary items required

Audi > Q7 > Electrical Equipment 27 - Removal and Installation. Battery. Special tools, testers and auxiliary items required Page 1 of 5 Audi > Q7 > 2007-2008 Electrical Equipment 27 - Removal and Installation. Battery Special tools, testers and auxiliary items required Pry lever 80-200 Vehicle Diagnostic, Testing and Information

More information

MANUAL CONTROL / SEMIAUTO TEMPERATURE CONTROL HEATING, VENTILATION AND AIR CONDITIONING SYSTEM

MANUAL CONTROL / SEMIAUTO TEMPERATURE CONTROL HEATING, VENTILATION AND AIR CONDITIONING SYSTEM SECTION 7C MANUAL CONTROL / SEMIAUTO TEMPERATURE CONTROL HEATING, VENTILATION AND AIR CONDITIONING SYSTEM CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit

More information

Audi A4 Current Flow Diagram No. 111 / 1

Audi A4 Current Flow Diagram No. 111 / 1 Page 1 of 9 Audi A4 Current Flow Diagram No. 111 / 1 CAN bus wiring from model year 2006 Notes: For information concerning Edition 10.2006 Position of relays and fuses Multi-pin connections Control units

More information

5/12/2018 Climate Control - Control Components - Description and Operation 2009 Ford F-150 MotoLogic

5/12/2018 Climate Control - Control Components - Description and Operation 2009 Ford F-150 MotoLogic 2009 F-150 Subarticles Report a problem with this article Electronic Manual Temperature Control (EMTC) Dual-Zone Electronic Automatic Temperature Control (EATC) SECTION 412-01: Climate Control 2009 F-150

More information

Use only gold-plated terminals when servicing terminals in harness connector. The respective fuses of Diesel-Direct fuel injection system must be OK:

Use only gold-plated terminals when servicing terminals in harness connector. The respective fuses of Diesel-Direct fuel injection system must be OK: Page 1 of 7 Volkswagen > A4 Platform > 1999-2005 1.9 Liter 4-Cyl. 2V TDI and TDI PD Generic Scan Tool, Engine Code(s): ALH, BEW 26 - Exhaust system, Emission controls Exhaust Gas Recirculation (EGR) system

More information

Power Sliding Door (PSD) Diagnostic Approach. Fixing Intermittent Malfunctions. Power Sliding Door (PSD) Diagnostic Information

Power Sliding Door (PSD) Diagnostic Approach. Fixing Intermittent Malfunctions. Power Sliding Door (PSD) Diagnostic Information Power Sliding Door (PSD) Diagnostic Information Power Sliding Door (PSD) The power sliding door (PSD) provides built-in diagnostics. This assists the service technicians during troubleshooting. The PSD

More information

Cylinder head, removing and

Cylinder head, removing and Page 1 of 35 15-2 Cylinder head, removing and installing Note: Replace cylinder head bolts. Always replace self-locking nuts, bolts as well as gaskets and O-rings. After installing a replacement cylinder

More information

FULL AUTOMATIC TEMPERATURE CONTROL HEATING, VENTILATION AND AIR CONDITIONING SYSTEM

FULL AUTOMATIC TEMPERATURE CONTROL HEATING, VENTILATION AND AIR CONDITIONING SYSTEM SECTION 7D FULL AUTOMATIC TEMPERATURE CONTROL HEATING, VENTILATION AND AIR CONDITIONING SYSTEM FATC (Full Automatic Temperature Control) is full automatic heater and airconditioning system that detects

More information

Volkswagen > New Beetle, New Beetle Convertible > Liter 4-Cyl. 2V Generic Scan Tool, Engine Code(s): AEG 24 - Components, Checking

Volkswagen > New Beetle, New Beetle Convertible > Liter 4-Cyl. 2V Generic Scan Tool, Engine Code(s): AEG 24 - Components, Checking Page 1 of 9 Volkswagen > New Beetle, New Beetle Convertible > 1998-2008 2.0 Liter 4-Cyl. 2V Generic Scan Tool, Engine Code(s): AEG 24 - Components, Checking. Throttle Valve Control Module J338, Checking

More information

Rzr Heater System Part #

Rzr Heater System Part # Rzr Heater System Part # 2878135 NOTE: This heater unit installs below the center of the dash. If you have a radio mount kit (Polaris Part # 2876897) you may need to cut the top front corner off the mount

More information

DIAGNOSIS AND TESTING

DIAGNOSIS AND TESTING 412-00-1 Climate Control System - General Information 412-00-1 DIAGNOSIS AND TESTING Climate Control System Refer to Wiring Diagrams Cell 54, Air Conditioning/Heater for schematic and connector information.

More information

A/C SYSTEM SPECIFICATIONS

A/C SYSTEM SPECIFICATIONS A/C SYSTEM SPECIFICATIONS A/C-HEATER SYSTEM - MANUAL 1997 Manual A/C-Heater System WARNING: To avoid injury from accidental air bag deployment, read and follow all SERVICE PRECAUTIONS and DISABLING & ACTIVATING

More information

Audi > B4 > Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly

Audi > B4 > Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly Audi > B4 > 1993 1995 2.8 Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly Removing The engine is removed from above, after being separated from the transmission. Note: All tie

More information

When Audi engineers were designing the

When Audi engineers were designing the Audi Climate Control Part One When Audi engineers were designing the 5000 sedan for the 1984 model year, they decided to upgrade the climate control system at the same time. The pre-1984 system was based

More information

Instrument cluster. Стр. 1 из 9. The following components are integrated in the instrument cluster: Instrument Cluster Control Module J285

Instrument cluster. Стр. 1 из 9. The following components are integrated in the instrument cluster: Instrument Cluster Control Module J285 Volkswagen Passat B6 2005 - Instrument cluster Стр. 1 из 9 90-1 Instrument cluster General information The following components are integrated in the instrument cluster: Instrument Cluster Control Module

More information

37. FATC (FULL AUTO TEMP. CONTROL) CIRCUIT 6810

37. FATC (FULL AUTO TEMP. CONTROL) CIRCUIT 6810 5156 6810 37. FATC (FULL AUTO TEMP. CONTROL) CIRCUIT 6810 1) CONDENSOR FAN, AIR MIX MOTOR, SUN SENSOR, WATER TEMP SENSOR A. CONNECTOR INFORMATION 6810 5157 Connector Number (Pin Number, Color) Connecting

More information

A/C-HEATER SYSTEM - AUTOMATIC

A/C-HEATER SYSTEM - AUTOMATIC A/C-HEATER SYSTEM - AUTOMATIC 1993 Toyota Celica 1993 Automatic A/C-Heater Systems Celica SPECIFICATIONS SPECIFICATIONS TABLE Application Specification Compressor Type 1.6L... Nippondenso 10PA15C 10-Cyl.

More information

CHAPTER 21 ENVIRONMENT CONTROL. Section Title Page

CHAPTER 21 ENVIRONMENT CONTROL. Section Title Page CHAPTER 21 ENVIRONMENT CONTROL Section Title Page 21-00 Description........................................ 21.1 21-10 Ventilation........................................ 21.3 21-11 Nose Vent................................

More information

Fuel injection system, servicing

Fuel injection system, servicing 24-1 Fuel injection system, servicing Component locations overview 1 - Oxygen sensor 1 before Three Way Catalyst G39 2 - Oxygen sensor 2 after Three Way Catalyst G130 3 - Engine Coolant Temperature sensor

More information

2015 F-250, 350, 450, 550 Super Duty DESCRIPTION AND OPERATION Procedure revision date: 04/28/2016. Climate Control System

2015 F-250, 350, 450, 550 Super Duty DESCRIPTION AND OPERATION Procedure revision date: 04/28/2016. Climate Control System Page 1 of 9 412-00 Climate Control System General Information and Diagnostics Climate Control System 2015 F-250, 350, 450, 550 Super Duty DESCRIPTION AND OPERATION Procedure revision date: 04/28/2016 WARNING:

More information

Transmission Control Systems: Testing and Inspection Procedures Component Tests

Transmission Control Systems: Testing and Inspection Procedures Component Tests Transmission Control Systems: Testing and Inspection Procedures Component Tests Control Module Pin Out Values Transmission Electrical Check Special tools, testers, etc. - Fluke (R) 83 Digital multimeter

More information

Different oils are used in automotive A/C systems, based on the type of refrigerant. Polyalkylene Glycol (PAG) oil is used for R-134a refrigerant.

Different oils are used in automotive A/C systems, based on the type of refrigerant. Polyalkylene Glycol (PAG) oil is used for R-134a refrigerant. Lubricants Automotive air conditioning lubricants are specially formulated because of how and where they operate. Air conditioning oils must be dry (having little or no water content) and mix with the

More information

TECHNICAL BULLETIN No:

TECHNICAL BULLETIN No: Date: 01 Mar 2007 CIRCULATE: TO Service Mgr Warranty Workshop Body Shop Parts X X X X X SECTION: REPLACES LS501-012, ISSUE 2, DATED 29-JUN-2006. CHANGES ARE HIGHLIGHTED WITH GREY BACKGROUND. 501-00 BODY

More information

Airbags, servicing. Airbag system, safety precautions WARNING!

Airbags, servicing. Airbag system, safety precautions WARNING! Page 1 of 75 69-40 Airbags, servicing Airbag system, safety precautions Checking, removing, installing and servicing may ONLY be performed by qualified personnel. Never perform tests using a test light

More information

Ultrasonic interior monitoring On Board Diagnostic (OBD)

Ultrasonic interior monitoring On Board Diagnostic (OBD) Page 1 of 44 01-108 Ultrasonic interior monitoring On Board Diagnostic (OBD) General Information The ultrasonic interior monitoring system is only offered in conjunction with the anti-theft system. The

More information

Ford F-100 Evaporator Kit (751153)

Ford F-100 Evaporator Kit (751153) an ISO 9001:2015 Registered Company 1968-72 Ford F-100 Evaporator Kit (751153) 18865 Goll St. San Antonio, TX 78266 Phone: 800-862-6658 Sales: sales@vintageair.com Tech Support: tech@vintageair.com www.vintageair.com

More information

Supersedes Technical Service Bulletin Group 87 number dated Aug. 28, 2006 to add 2008 model years and for reformatting.

Supersedes Technical Service Bulletin Group 87 number dated Aug. 28, 2006 to add 2008 model years and for reformatting. 87 07 12 2010146/4 Nov. 19, 2007 Supersedes Technical Service Bulletin Group 87 number 06-03 dated Aug. 28, 2006 to add 2008 model years and for reformatting. Vehicle Information Unpleasant odor from heating

More information

2000 Volkswagen Jetta GL

2000 Volkswagen Jetta GL Fig. 8: Locating Battery Fuse Panel Fuses Courtesy of VOLKSWAGEN UNITED STATES, INC. FUSE IDENTIFICATION (BATTERY FUSE PANEL) Fuse No. Amp Circuits Protected Rating 162 Engine Codes 50 Secondary Air Injector

More information

TABLE OF CONTENTS Subject Page

TABLE OF CONTENTS Subject Page TABLE OF CONTENTS Subject Page Control Panel................................................2 Control Module..............................................6 Substitute Value Operation......................................7

More information

HVAC System: Engine Cooling, Controls and Communication

HVAC System: Engine Cooling, Controls and Communication Course #S-AC07-04.01VCT HVAC System: Engine Cooling, Controls and Communication Participant Guide Revised: 01/24/11 Copyright 2011, General Motors Company, All Rights Reserved Caution Danger: In order

More information

1993 ENGINE PERFORMANCE Volkswagen System & Component Testing - Digifant. EuroVan

1993 ENGINE PERFORMANCE Volkswagen System & Component Testing - Digifant. EuroVan Article Text ARTICLE BEGINNING 1993 ENGINE PERFORMANCE Volkswagen System & Component Testing - Digifant EuroVan INTRODUCTION Since many computer-controlled and monitored components set a trouble code if

More information

AN82.10-P-0001FB Retrofit xenon headlamps MODEL 210.### 1# as of

AN82.10-P-0001FB Retrofit xenon headlamps MODEL 210.### 1# as of AN82.10-P-0001FB Retrofit xenon headlamps 3.11.99 MODEL 210.### 1# as of 1.7.99 Illustrated on model 210 sedan A51 Headlamp range adjustment rear A52 Front (headlamp range adjustment) E1 Left lamp unit

More information

1 of 2 5/17/17, 1:22 PM

1 of 2 5/17/17, 1:22 PM 1 of 2 5/17/17, 1:22 PM Trim Molding, Removing and Installing Special tools, testers and auxiliary items required Wedge Set (T10383) Removal Wedge (T40233) Removing - Starting at the front, pry the trim

More information

A/C SYSTEM GENERAL DIAGNOSTIC PROCEDURES

A/C SYSTEM GENERAL DIAGNOSTIC PROCEDURES Article Text ARTICLE BEGINNING 1993 AIR CONDITIONING & HEAT A/C General Diagnostic Procedures Diagnosis is an important first step in A/C system servicing. To save time and effort, systems should be carefully

More information

HEATING & AIR CONDITIONING

HEATING & AIR CONDITIONING VA HEATING & AIR CONDITIONING 24-1 HEATING & AIR CONDITIONING TABLE OF CONTENTS page HEATING & AIR CONDITIONING DESCRIPTION...1 OPERATION...2 DIAGNOSIS AND TESTING A/C PERFORMANCE...3 HEATER PERFORMANCE

More information

Service Training. Audi A5 - Networking. Self-Study Programme 395

Service Training. Audi A5 - Networking. Self-Study Programme 395 Service Training Audi A5 - Networking Self-Study Programme 395 Innovations in the electrical system and electronics on the Audi A5 The number of s in motor vehicles continues to increase, and the Audi

More information

ALTERNATOR REQUESTED INFORMATION. Vehicles With Dual Generator [ Engine Mount - LH ] 2007 Ford Pickup 6.0L Eng F350 Super Duty

ALTERNATOR REQUESTED INFORMATION. Vehicles With Dual Generator [ Engine Mount - LH ] 2007 Ford Pickup 6.0L Eng F350 Super Duty ALTERNATOR 2007 Ford Pickup 6.0L Eng F350 Super Duty REQUESTED INFORMATION Vehicles With Dual Generator [ Engine Mount - LH ] Fig 1: Rotating Drive Belt Tensioner Clockwise 1. Remove the accessory drive

More information

00 02 Apr. 24, Service

00 02 Apr. 24, Service Subject: Model(s): Driver s Side Airbag, On Board Diagnostic (OBD) All 2000 Group: Number: Date: 01 00 02 Apr. 24, 2000 Supersedes T.B. group 01 number 99 20 dated Dec. 8, 1999 Black revision bars indicate

More information

1969 CAMARO VCZ-A

1969 CAMARO VCZ-A 969 CAMARO w/o FACTORY AIR 55070-VCZ-A 8865 GOLL ST. - SAN ANTONIO, TX. - 78266 ph.20-654-77 - fax 20-654-33 905070-VCZ-A /22/05, 69 CAMARO w/o FAC. AIR INSTRUCTIONS PG OF 20 969 CAMARO w/o FACTORY AIR

More information

Front seats. Special tools and equipment. VAS 5094 airbag adapter. Connecting page 72-9.

Front seats. Special tools and equipment. VAS 5094 airbag adapter. Connecting page 72-9. Page 1 of 23 72-1 Front seats Special tools and equipment VAS 5094 airbag adapter Connecting page 72-9. Page 2 of 23 72-2 Front seats, removing and installing WARNING! Before starting work on seats, connect

More information