Please note that any machine outside the specifications may be put into a consolation class. This class will not receive any school points nor prizes.
|
|
- Phillip Wilkins
- 5 years ago
- Views:
Transcription
1 New Zealand National Secondary Schools Minibike Racing Club Inc. Specifications of Bike Classes. Standard Air-Cooled Bikes: 50CC. Aim: To encourage accurate construction and provide a predetermined overall standard so no competitor can obtain an unfair advantage, by unacceptable modifications. This may be determined by the specifications committee. Please note that any machine outside the specifications may be put into a consolation class. This class will not receive any school points nor prizes. 1 Frames: All frames must be of mild steel construction and made in the school workshop with suitably braced headstock. No commercial frames allowed. 1.1 Bare metal steel frames must be protected from the elements i.e. painted, powder coated etc 1.2 Racing numbers to be visible on the front of the minibike for identification purposes. 2 Front Forks/Head stocks or Triple clamps: Steel or alloy construction, produced by the student. No commercial components allowed. This includes any Triple clamps supplied with the kit. HEAD STOCK ANGLES. SHOULD BE BETWEEN 22 TO 25 DEGREES. Angles greater than 25 degrees will be placed in the Out of Specs consolation class. 2.1 Triple clamps must be produced by the students in a school workshop environment. 50cc Motard triple clamps that come with the kit can be copied but not used. 3 Engines: The standard RSA115 engine is the only acceptable engine in this class, in 50cc form. The engine cannot be modified in any way, this includes the following: No alterations to the engine s transfer ports or adding of extra ports. This includes inlet and exhaust ports. No alterations to the combustion chamber that will result in a change of compression ratio The replacement of the standard steel reed valve with a carbon fibre or glass fibre replacement is not acceptable. Alteration of the ignition timing by the use of timing keys is not allowed. Lightening of the flywheel is not allowed, this includes removal of cooling fins. Race ignition coils are not acceptable. 4 Carburettor/ Fuel Tank, Air filter: The standard E3 carburettor of the round piston type is the only acceptable variant. No flat slide carbs. No intentional modification or adjustment of standard jet size needles (no drilling, filing or other intentional modification) No adjustable carb needle jets. The standard air filter as supplied with the NRCD Kit can be used. FUEL TANKS MUST BE RETAINED IN A WAY SO THAT WHEN THE FUEL CAP IS REMOVED THE TANK CANNOT FALL OUT OF THE SEAT UNIT. Note: A tight fit into the seat unit is not good enough. 1 Copyright 2019 N.Z.N.S.S.M.B.R.C.INC.
2 5 Gearing and Clutches: Acceptable gear ratios are. 6 x 68 7 x 68 8 x 68 Clutches should be of the standard type. Adjustable race style will not be allowed. ENGINE DRIVE SPROCKETS MUST BE COVERED TO PREVENT STUDENT BODY PARTS FROM HITTING THE CHAIN DURING OPERATION. 6 Exhausts: The only acceptable system will be the small black system as supplied in the Newmanz kits unmodified. No aftermarket exhausts. No S shaped expansion chambers. 7 Leading Dimensions: Maximum wheel base 850mm. Measured from the centre of the front axle to the centre of the rear axle. ANY MACHINES WITH A WHEEL BASE THAT EXCEEDS THE MAXIMUM BY MORE THAN 10 MM WILL BE PUT IN THE OUT OF SPECS CONSOLATION CLASS. Maximum seat height 500mm measured from a point immediately to the rear of the fuel tank, on top of the seat. Maximum height to front yoke 550mm. Not including fairing. Maximum handlebar height to highest point from ground 560mm. [10mm above top yoke] Maximum width of handlebars is 550mm. HANDLE BARS MAY NOT BE FITTED LOWER THAN THE BOTTOM TRIPLE CLAMP/BOTTOM YOKE. RIDING/ SEATING POSITION. The riders foot pedals will be fastened to the frame. The foot rests may not be any further backwards than 150 mm behind the engine drive gear and 150 forward of the rear axle. Foot rests in awkward positions, as decided upon by the testers, will be forwarded to the Specifications/ safety committee. 8 Brakes/ Axles. Standard brake calliper s, one only fitted to the front and rear wheels. Front/rear wheels must both be braked. REAR AXLE RETAINING NUTS MUST BE HELD IN PLACE WITH SUITABLE LOCKING DEVICES. For example: Use of castellated nuts and split pins, use of new nylock nuts, drilled axle and wired, R clips, drilled axle and wiring to rear fork. Any of the above locking devices can be used to prevent movement of the rear axle during use whilst racing and to prevent movement of set chain adjustment. 9 Attention: It is not our intention to stop the pupils from innovating or to dampen their enthusiasm. Far from it, we will actively encourage that sort of approach. We wish that pupils who spend money and modify their machines do so in a spirit of honesty and fair play. To this end they should enter the modified air-cooled class. The organising committee will reserve the right to request that the first 3 placed bikes in any standard class be dismantled and inspected at the conclusion of racing and before prizes are presented. If any modifications occur, the student will be disqualified, all points will be forfeited, and they will be excluded from participating in the following years event. The committee s decision will be final. A standard gasket set will be provided so the student can reassemble the bike at no cost to the student. 2 Copyright 2019 N.Z.N.S.S.M.B.R.C.INC.
3 All competitors need to have riding experience practice to ensure stable riding control before orientation laps at the race circuit Handle bar ends must be plugged and foot pegs with rounded ends. All competitors need to have riding experience practice to ensure stable riding control before orientation laps at the race circuit. 3 Copyright 2019 N.Z.N.S.S.M.B.R.C.INC.
4 Classification of Modified Air-Cooled Bikes: Aim: To encourage accurate construction and provide a predetermined overall standard so no competitor can obtain an unfair advantage, by unacceptable modifications. This may be determined by the specifications committee. Please note that any machine outside the specifications may be put into a consolation class. This class will not receive any school points nor prizes. 1 Frames: All frames must be of mild steel construction and made in the school workshop with suitably braced headstock. No commercial frames allowed. Bare metal steel frames must be protected from the elements i.e. painted, powder coated etc Racing numbers to be visible on the front of the minibike for identification purposes. Handle bar ends must be plugged. Footrests must be rounded. Racing numbers must be visible 2 Front Forks/Head stocks or Triple clamps: Steel or alloy construction, to be produced by the student. No commercial components allowed. FORK ANGLES / HEAD STOCK ANGLES AS STANDARD AIR-COOLED FRAMES DEGREES. 3 Engines: The RSA115 engine is the only acceptable engine in this class. The engine can be modified in any way. MODIFIED BIKES MUST ENTER THE MODIFIED CLASS. 4 Carburettor/Air filter/ Fuel tank. Carb air filter Completely open. Fuel tank fitment as standard air-cooled i.e.. fuel tank must be retained in a way so that when the fuel cap is removed the tank cannot fall out of the seat unit a tight fit into the seat unit it not good enough. 4 Copyright 2019 N.Z.N.S.S.M.B.R.C.INC.
5 5 Gearing and Clutches: Gear ratios are over to the student. Adjustable race style clutches are allowed. DRIVE SPROCKETS MUST BE COVERED TO PROTECT THE RIDER. 6 Exhausts: Any system will be acceptable, after market exhausts and S shaped expansion chambers can be used. 7 Leading Dimensions: Maximum wheel base 850mm. Measured from the centre of the front axle to the centre of the rear axle. AXLE POSITION NO MORE THAN 10 MM OUTSIDE SPECIFICATIONS. FOOT REST POSITION AS STANDARD BIKES, 150 MM BEHIND DRIVE GEAR AND 150 FORWARD OF THE REAR AXLE. Maximum seat height 500mm measured from a point immediately to the rear of the fuel tank, on top of the seat. Maximum height to front yoke 550mm. Not including fairing. Maximum handlebar height to highest point from ground 560mm. [10mm above top yoke] Maximum width of handlebars is 550mm. HANDLE BARS Mounted NO LOWER THAN BOTTOM TRIPLE CLAMP. 8 Brakes Axle s: Front/rear wheels must be braked. REAR AXLE NUTS MUST BE WIRED. Nylock nuts are acceptable. 5 Copyright 2019 N.Z.N.S.S.M.B.R.C.INC.
6 Classification of Modified Water Cooled Bikes: : To encourage accurate construction and provide a predetermined overall standard so no competitor can obtain an unfair advantage, by unacceptable modifications. This may be determined by the specifications committee. Please note that any machine outside the specifications may be put into a consolation class. This class will not receive any school points nor prizes. 1 Frames: All frames must be of mild steel construction and made in the school workshop with suitably braced headstock. Handle bar ends must be plugged, & footrests rounded. No commercial frames allowed. 2 Front Forks/Head stocks or Triple clamps: Steel or alloy construction to be produced by the student. No commercial components allowed. 3 Engines: The basic 38cc. water-cooled engine is the only acceptable engine in this class. The engine can be modified in any way. 50cc, Big bore kits can be used. BUT MUST BE ENTERED IN THE MODIFIED CLASS 4 Carburettor/Air filter: Completely open. 5 Gearing and Clutches: Gear ratios are over to the student. Adjustable race style clutches are allowed. 6 Exhausts: 6 Copyright 2019 N.Z.N.S.S.M.B.R.C.INC.
7 Any system will be acceptable, after market exhausts and S shaped expansion chambers are to be encouraged. 7 Leading Dimensions: Maximum wheel base 850mm. Measured from the centre of the front axle to the centre of the rear axle. AXLE POSITION NO MORE THAN 10 MM OUTSIDE SPECIFICATIONS. FOOT REST POSITION AS STANDARD BIKES, 150 MM BEHIND DRIVE GEAR. Maximum seat height 500mm measured from a point immediately to the rear of the fuel tank, on top of the seat. Maximum height to front yoke 550mm. Not including fairing. Maximum handlebar height to highest point from ground 560mm. [10mm above top yoke] Maximum width of handlebars is 550mm. HANDLE BARS Mounted NO LOWER THAN BOTTOM TRIPLE CLAMP. 8 Brakes: Front/rear wheels must be braked. REAR AXLE NUTS MUST BE WIRED. 7 Copyright 2019 N.Z.N.S.S.M.B.R.C.INC.
8 Classification of Standard Water Cooled Bikes: Aim: : To encourage accurate construction and provide a predetermined overall standard so no competitor can obtain an unfair advantage, by unacceptable modifications. This may be determined by the specifications committee. Please note that any machine outside the specifications may be put into a consolation class. This class will not receive any school points nor prizes. To encourage accurate construction and provide a predetermined overall standard so no competitor can obtain an unfair advantage, by unacceptable modifications. This may be determined by the specifications committee. 1 Frames: All frames must be of mild steel construction and made in the school workshop with suitably braced headstock. No commercial frames allowed. 2 Front Forks/Head stocks or Triple clamps: Steel or alloy construction produced by the student and made in the School Workshop. No commercial components allowed. 3 Engines: The standard water-cooled engine is the only acceptable engine in this class, in 38cc form. The engine cannot be modified in any way. No alterations to the combustion chamber. No alterations to the compression ratio. The replacement of the standard steel reed valve with 8 Copyright 2019 N.Z.N.S.S.M.B.R.C.INC.
9 a carbon fibre or glass fibre replacement is not acceptable. Alteration of the ignition timing by the use of timing keys is not allowed. Lightening of the flywheel is not allowed. Race ignition coils are not acceptable. 4 Carburettor/Air filter: The standard carburettor of the flat side type is the only acceptable type. No alteration to the carb jets. No adjustable carb needle jets. The standard pod filter supplied with the kit is to be used. 5 Gearing and Clutches: As supplied in the kit. 6 Exhausts: The only acceptable system is the water-cooled expansion chamber as supplied by Newmanz. 7 Leading Dimensions: Maximum wheel base 850mm. Measured from the centre of the front axle to the center of the rear axle. Maximum seat height 500mm measured from a point immediately to the rear of the fuel tank, on top of the seat. Maximum height to front top yoke 550mm. Not including fairing. Maximum handlebar height to highest point from ground 560mm. [10mm above top yoke] Maximum width of handle bars 550mm. 8 Brakes: Standard brake callipers one to be fitted to both the front/rear wheels. REAR AXLE NUTS MUST BE WIRED. 9 Handle bar ends must be plugged, & footrests rounded. 10 Attention: It is not our intention to stop the pupils from innovating or to dampen their enthusiasm. Far from it we will actively encourage that sort of approach. We wish that pupils who spend money and modify their machines do so in a spirit of honesty and fair play. To this End they should enter the modified water-cooled class. The organizing committee will reserve the right to request that the first 3 Placed bikes in any standard class be dismantled and inspected at the conclusion of racing and before prizes are presented. If any Modifications occur, the student will be disqualified, all points will be forfeited, and they will be excluded from participating in the Following year s event. The committee s decision will be final. A water-cooled gasket set will be provided so the student can reassemble the bike at no cost to the student. 9 Copyright 2019 N.Z.N.S.S.M.B.R.C.INC.
Please note that any machine outside the specifications may be put into a consolation class. This class will not receive any school points nor prizes.
Classification of 70cc Road Bike: Aim: To encourage accurate construction and provide a predetermined overall standard so no competitor can obtain an unfair advantage, by unacceptable modifications. This
More informationAPPENDIX C Mini Motocross Homologation (Off Road)
APPENDIX C Mini Motocross Homologation (Off Road) To view all Homologated Motorcycles refer to the MNZ Website www.mnz.co.nz 1.0 Performance Enhancement Objectives: In the event of ambiguity, these rules
More information2019 New Zealand Superbike Championship
2019 New Zealand Superbike Championship Support Class Supplementary Regulations Covering: Superstock 600 (all rounds) Supersport 150 (Rounds 1, 4 & 5) Superstock 600: This class of motorcycle requires
More informationREGULATIONS AND SPECIFICATIONS FOR THE 2019 WPMC POWERSPORT MOTORCYCLE RIDERS CLUB CHAMPIONSHIP (161774/144)
REGULATIONS AND SPECIFICATIONS FOR THE 2019 WPMC POWERSPORT MOTORCYCLE RIDERS CLUB CHAMPIONSHIP (161774/144) 1. AIM OF THE CHAMPIONSHIP 1.1 This is a Club status championship. 1.2 The aim of the championship
More informationBMCRC/BMZRC MZ Technical Regulations 2017
BMCRC/BMZRC MZ Technical Regulations 2017 Eligible machines MZ TS & MZ ETZ 250 & 251 Plus 301 & Saxon Swinging arm and Frame only. Crankcases, Barrels, Heads, Forks, Carburettor, Frames, Swinging Arm and
More informationNOVICE 1, 2 & JUNIOR 1 & 2 DIVISIONS
NOVICE 1, 2 & JUNIOR 1 & 2 DIVISIONS 708 BRIGGS LOCAL OPTION 206 Briggs & Stratton (B&S) Model 124332 Type 8201 only. The intent of this class is to provide a sealed, simple-to-operate, ultra dependable
More informationNo Limits Racing 2015 Technical Regulations
No Limits Racing 2015 Technical Regulations - Metzeler Newcomer 600 & 1000 in association with Sorrymate.com - All machines competing in any 2015 No Limits Cup Races must comply with these regulations.
More informationMinistock Rule Update
Ministock Rule Update 08-08-17 Following on from the positive feedback received under the Consultation process in late 2016, the Board have agreed to the following rule updates to be made on the Ministocks.
More information45.06 Fuel Refer Chapter 22 Fuel, as run, to comply with tests under chapter 22.01
CHAPTER 45 PARILLA LEOPARD 125cc and PARILLA LEOPARD X30 125cc Preamble It is expected that this class will continue to evolve during its early life and the promoters of the class reserve the right to
More informationMKX 50 PRO MKX 50 BIGFOOT MKX 50 MONGOOSE
MKX 50 PRO MKX 50 BIGFOOT MKX 50 MONGOOSE CHASSIS 1 81108001 PERIMETRAL ALUMINIUM CHASSIS MKX 1 2 81108002 FIXING BRACKET SET MKX ENGINE 2 3 81108003 FIXING SCREW MKX ENGINE 2 4 81108004 RIGHT FOOTREST
More informationCurrent Price List Jan 2013
Crankshafts Current Price List Jan 2013 Pearson Flywheel Assembly standard ⅞ T/S Shaft 1⅛ D/S Shaft, Carrillo Con-Rod balanced to your Piston. 88 Stroke for Gold Star Crankcases. Direct replacement. 800.00
More informationTECHNICAL BULLETIN. Formula Vee Technical Regulations. REFERENCE:
Bulletin Number: B15/038 Implementation Date: 01/01/2016 TECHNICAL BULLETIN Formula Vee Technical Regulations REFERENCE: http://docs.cams.com.au/manual/race/ra14-formula-vee-2015-1.pdf RATIONALE: To update
More information2016 MODEL INFORMATION
2016 MODEL INFORMATION MODEL NAME KX65 MARKETING CODE KX65A Version: 2 June 2015 Canadian model may not be exactly as shown. OVERVIEW Kawasaki s smallest motocross racer is loaded with big KX features
More information2018 Junior Sprint Rules
2018 KidSprint Engine Rules Briggs World Formula 2018B All parts must be Briggs & Stratton factory production parts unless otherwise noted in these rules. No machining, polishing or alteration of any parts
More informationHonda Performance Development GXH50 Class Information
Honda Performance Development GXH50 Class Information 10/30/13 The intent of the class is to provide a low cost, simple and reliable engine package for beginning Kid Karters to utilize. The engine must
More informationMotorcycle parts compatibility on ebay.co.uk
Motorcycle parts compatibility on ebay.co.uk Review the full list of categories and subcategories in which you can list motorcycle and scooter parts. Last updated: 10 August 2016 Motorcycle Parts (10063)
More informationMini-bike excitement hits schools
Mini-bike excitement hits schools PHOTOGRAPHS: ROGER EMMERSON Out go toolboxes, candle-holders, metal stools. Here come mini motorbikes. By Roger Emmerson The idea of the air-cooled minibike as a school
More information122 Fasola Road, Sequim Wa (360) Morgan +4 Engine Rebuild Brochure
122 Fasola Road, Sequim Wa 98382 (360) 582-9020 Morgan +4 Engine Rebuild Brochure This brochure is intended to show the extensiveness of the work performed on the TR engines that I rebuild. I treat each
More information100cc REEDJET USA TaG
100cc REEDJET USA TaG FEATURES Cylinder Volume 100 cm³ max Bore 48.20 mm Max. theoretical bore 48.53 mm Stroke 54.05 mm max Cooling system Air Inlet system Reed valve Number of carbs 1 Tillotson Carburettor
More informationTechnical data. Part Thread (mm) Nm ±10% Tolerance Sidestand
section 3 - Torque settings Frame torque settings Sidestand Stand sensor bolt 5 Pre-applied threadlocker Stand plate fixing screw M10x25 43 Pre-applied threadlocker Side stand fastening pin Side stand
More informationNATIONAL HOMOLOGATION FORM KARTING ENGINE X30 SUPER - TAG
NATIONAL HOMOLOGATION FORM KARTING ENGINE X30 SUPER - TaG Manufacturer IAME S.P.A - ZINGONIA Make IAME Model X30 SUPER - TAG Validity of the homologation 6 years Number of pages 51 This Homologation Form
More informationClasses INC. Northeast Snowmobile Racing INC SNOW DRAG RACING. Classes. Amateur: ( $15 Entry Fee + $5 Insurance Fee) Stock: 500, 600, 700, 800, Open
INC Northeast Snowmobile Racing INC Classes SNOW DRAG RACING Classes Amateur: ( $15 Entry Fee + $5 Insurance Fee) Stock: 500, 600, 700, 800, Open Improved Trail: 500, 600, 700, 800, Open Pro: ( $25 Entry
More informationUSA SUPER SHIFTER 175cc
USA SUPER SHIFTER 175cc FEATURES Cylinder volume 174.46 cm³ (Max 176.6 cm³) Bore 63.90 mm Max. theoretical bore 64.26 mm Stroke 54.40 mm Distance between conrod centers 115 mm Cooling system Water Inlet
More informationMINI ROK 2016 IDENTIFICATION SHEET
IDENTIFICATION SHEET This Identification Sheet reproduces descriptions, illustrations and dimensions of the MINI ROK engine to be used in the MINI ROK CUP recognised by Motorsport South Africa PICTURE
More informationENGINE. IAME SPA IAME KA cc REEDJET AUS TaG 6 Years 28
ENGINE Manufacturer Make Model Validity of the homologation Number of pages IAME SPA IAME KA 100-100cc REEDJET AUS TaG 6 Years 28 This Homologation Form reproduces descriptions, illustrations and dimensions
More information2004 Model Information
Version: 4 Jun 2003 2004 Model Information MARKETING CODE: KX125M MODEL NAME: KX125 Note: While material contained herein may be used in the preparation of press releases, technical service material and
More informationNATIONAL HOMOLOGATION FORM - ENGINE
NATIONAL HOMOLOGATION FORM - ENGINE Homologation N Manufacturer VORTEX Make MINI ROK Model 60CC Validity of the homologation 6 years Number of pages 32 This Homologation Form reproduces descriptions, illustrations
More informationWorld Formula TECH MANUAL
World Formula TECH MANUAL Section 1 General Rules 1. Only stock Briggs & Stratton World Formula Model # 124435-8101 will be used in this class except as provided in this Tech manual. All parts will be
More information2019 VSP 602 Late Model Rules
2019 VSP 602 Late Model Rules General: A. Raceceivers must always be used on track. B. Transponders must be mounted on RR Axle tube. C. Drivers must remain in car at all times when on track, unless instructed
More informationXCR 600/ XLT TRIPLE PIPE SET P.N Installation Instructions
1994-97 XCR 600/1993-97 XLT TRIPLE PIPE SET P.N. 09-5970 Installation Instructions Read instructions carefully before installation 1-Remove stock exhaust, Y-pipe, and rear muffler support. 2-Install three
More informationMotorsport South Africa
Motorsport South Africa SOUTH AFRICAN KARTING COMMISSION HOMOLOGATION SCHEDULE MAXTERINO MX-60 Version 1 2017-01-25 MSA Ref. Manufacturer MAXTER S.R.L. Distributor Ed Murray Racing cc Model Maxterino Period
More informationMSA Kart Race Yearbook 2014
B1.0 Group Cadet B1.1 Class Formula Cadet Affiliation MSA B1.2 Introduction. Starter class from 8 years of age with maximum retail prices for basic chassis and engine. Chassis, brakes and engine are homologated
More informationREGULATIONS AND SPECIFICATIONS FOR THE WESTERN CAPE SHORT CIRCUIT MOTORCYCLE 150 JUNIOR CHAMPIONSHIP 2015 MSA WESTERN CAPE MOTOR SPORT CIRCULAR WC
REGULATIONS AND SPECIFICATIONS FOR THE WESTERN CAPE SHORT CIRCUIT MOTORCYCLE 150 JUNIOR CHAMPIONSHIP 2015 MSA WESTERN CAPE MOTOR SPORT CIRCULAR WC 3/2015 These Regulations are to be read in conjunction
More informationWORLD OF MOTORSPORT ZA
WORLD OF MOTORSPORT ZA P.O. Box 12387, Brakpan North, 1545 18 Main Reef Rd Brakpan (on the premises of Rock Raceway) Tel: 011-740 1206 / 740 8315 Fax: 086 508 2388 email: womza@telkomsa.net www.womzasa.co.za
More informationTECHNICAL BULLETIN. 1 st CATEGORY RACING CARS FORMULA VEE TECHNICAL REGULATIONS REFERENCE: RATIONALE: To clarify the Formula Vee Technical Regulations
Bulletin Number: B15/006 Implementation Date: 26/03/2015 TECHNICAL BULLETIN 1 st CATEGORY RACING CARS FORMULA VEE TECHNICAL REGULATIONS REFERENCE: http://docs.cams.com.au/manual/race/ra14-formula-vee-2015-1.pdf
More informationCRF125FB MOTORCYCLES.HONDA.COM.AU
CRF125FB MOTORCYCLES.HONDA.COM.AU The Honda CRF125FB (Big Wheel) will be everything a young entry rider could possibly hope for. With similar specs to the CRF125F, the CRF125FB has a bigger bike feel and
More informationTRX450ER MOTORCYCLES.HONDA.COM.AU
TRX450ER MOTORCYCLES.HONDA.COM.AU Where do you go when you want a four-wheeler that's not just all work and no play? Look no further than the TRX450ER. INTRODUCTION ENGINE/DRIVETRAIN Powerful four-stroke
More information1 REGULATIONS AND SPECIFICATIONS FOR THE 2015 SHORT CIRCUIT MOTORCYCLE 150 SENIOR CHAMPIONSHIP MSA WESTERN CAPE MOTORSPORT CIRCULAR WC 20/
1 REGULATIONS AND SPECIFICATIONS FOR THE 2015 SHORT CIRCUIT MOTORCYCLE 150 SENIOR CHAMPIONSHIP MSA WESTERN CAPE MOTORSPORT CIRCULAR WC 20/2015 1. CONTROLLERS Will be the Western Province Short Circuit
More informationMotor Cycle Mechanic 1
Motor Cycle Mechanic 1 Training Objective: Motor Cycle is a popular use in urban as well as rural areas throughout the country. This course aims at producing semi skilled workers who can carryout minor
More information1 General Specifications
Chevettes s on Ice Supplemental Regulations (CH) 2017 MAJOR CHANGE FOR THE 2017+ SEASON: Addition of TSMI 15 blue street studs to Hankook tires. MAJOR CHANGE FOR THE 2015+ SEASON: Welded / Locked differential
More informationNATIONAL HOMOLOGATION FORM - ENGINE
NATIONAL HOMOLOGATION FORM - ENGINE Homologation N Manufacturer VORTEX Make DVS JNR Model 125CC Validity of the homologation 10 years Number of pages 30 This Homologation Form reproduces descriptions,
More informationMini Motorcycle Racing Club Of Ireland Technical Regulations Published 2019
Section 1 Scuitineering 1.1 All riders and their machines must undergo scrutineering on the morning of each race meeting. Riders and machines must pass the below basic tests before being allowed on the
More information2017 Model Information
2017 Model Information MODEL NAME: KX85 Big Wheel MODEL CODE: KX85DHF THE HOTTEST RACE BIKES FOR FUTURE CHAMPIONS At both the amateur and professional levels, Kawasaki has long been the dominant brand
More informationlbs sq. Camshaft bush ID 0.5 ± Clearance bush to camshaft ±
GENERAL Cubic capacity 347 C.C. Stroke 93 mm. / 3.6614 Cylinder bore Compression ratio Max compression at kick starter speed 2 23 /32 = 2.7187 ± 0.0005 (Re-bore to + 0.02 when wear exceeds 0.008 ). Note:
More informationLocal Option 206 Rules Manual Section 1 General Rules 1. Only stock Briggs & Stratton LO206 # engine will be allowed in this class.
Local Option 206 Rules Manual Section 1 General Rules 1. Only stock Briggs & Stratton LO206 # 124332-8201engine will be allowed in this class. o All parts will be stock unaltered Briggs & Stratton Animal
More informationBSA Goldstar Parts - Price List Feb Exhaust Lifter Cable Exhaust Lifter Cable Holder S/S 9.00
Rocker Boxes 65-1137 Exhaust Lifter Cable 15.00 65-1163 Exhaust Lifter Cable Holder S/S 9.00 2-443 Exhaust Lifter Cable Holder Nut S/S 0.50 65-401 Exhaust Lifter Spindle Felt 2.00 65-387 Exhaust Lifter
More informationPARILLA LEOPARD RL 125 TECHNICAL SPECIFICATIONS
PARILLA LEOPARD RL 125 VERSION 4 / 2012 UPDATED September 6 th, 2012 DOCUMENT UPDATE SCHEDULE It is certified that the updates listed below have been approved by the Australian Karting Association and
More informationAll items, if not expressly mentioned in the following set of rules, must remain as originally produced by the manufacturer.
SUPERSTOCK 600 - Technical Regulations 0.1 Discipline Specifications Superstock 600 To be admitted in the 2005 UEM Superstock 600 European Championship motorcycles require an FGSPORT homologation based
More informationXLT SPECIAL TRIPLE PIPE SET P.N Installation Instructions
1995-97 XLT SPECIAL TRIPLE PIPE SET P.N. 09-598 Installation Instructions Revised 8/20/02 Read instructions carefully before installation 1 - Remove stock exhaust, Y-Pipe, front and rear muffler support.
More information10. Oil injection pump must remain functional and in place lines may be removed and plugged. Premix gasoline may be used.
STOCK SNOWMOBILE GENERAL REQUIREMENTS 1. The snowmobile must use OEM clutch, suspension, gas tank, cowl, hood and engine for the snowmobiles year and model. Factory options are not 2. Snowmobile and driver
More informationKid Sprint Engine Rules Briggs World Formula
Kid Sprint Engine Rules Briggs World Formula 2017 Jr Sprint Engine Rules Briggs World Formula effective 2/1/2017. All parts must bebriggs & Stratton factory production parts unless otherwise noted in these
More informationAMMC JUNIOR CLASS RULES
AMMC JUNIOR CLASS RULES Classes Semi Pro: Pro: Ages 9-13, Machine: 0-550cc Fan Cooled Ages 13-17, Machine: 0-600cc Fan Cooled/Liquid Cooled GENERAL Snowmobile must have OEM engine, hood, intake, exhaust,
More informationMRO 600 CLASS REGULATIONS 2019
MRO 600 CLASS REGULATIONS 2019 These regulations are the MRO 600 Regulations and also cover the Rookie 600 class. Note: If you are planning to take your bike to compete at BSB as a private entrant under
More informationSherco Engine Teardown and Assembly Manual
Sherco Engine Teardown This Manual is provided as a guide for: Removing the engine from the frame Splitting the cases Complete Disassembly of the engine Reassembly of the engine Reinstallation back in
More informationENGINE. Manufacturer IAMEs.p.a. Category. Homologation Period. Pages 16. Model, Type SIGNATURE AND STAMP OF AKA SIGNATURE AND STAMP OF APPLICANT
1 ENGINE Manufacturer IAMEs.p.a. Category Make Model, Type PARILLA Leopard X30 125cc RL - TaG - AUS Homologation Period Pages 16 This homologation sheet reproduces description, illustrations and dimensions
More informationEverything that is not explicitly authorised and prescribed in the following rules is forbidden.
DMSB Technical Regulations 2018 for the Superstock 600 class As at: 13.06.2018 changes are shown in italics In case of doubt only the German text of the regulations is binding. The following rules are
More informationKARTSPORT NEW ZEALAND MANUAL BRIGGS & STRATTON LO206
KARTSPORT NEW ZEALAND MANUAL N15 BRIGGS & STRATTON LO206 Issue 2017-1 published and effective 1-7-17 N15 BRIGGS & STRATTON LO206 N15.1 GENERAL SPECIFICATIONS N15.1.1 These engine specifications are under
More information2017 TAG 125cc Stock Moto Specifications and Tech Procedures
2017 TAG 125cc Stock Moto Specifications and Tech Procedures Spirit and intent The following rules are applied in order to provide fair and equal competition within the class. The specifications and limitations
More informationPLEASE BE SURE YOU HAVE READ AND UNDERSTAND THE GENERAL RULES, SAFETY RULES AND DRIVER SAFETY EQUIPMENT BEFORE CONTINUING.
2017 SPORTSMAN RULES Any rule changes made in 2017 are highlighted in RED. *Speedway Officials shall be empowered to permit minor deviations from any of the specifications herein or impose any further
More informationX30 CHALLENGE INTERNATIONAL TECHNICAL REGULATIONS 2017 PART 2 ENGINES
X30 CHALLENGE INTERNATIONAL TECHNICAL REGULATIONS 2017 PART 2 ENGINES X30 CHALLENGE INTERNATIONAL TECHNICAL REGULATIONS 2017 - PART 2: ENGINES ARTICLE 1 - ENGINE IAME X30 125cc RL TaG - X30 SENIOR & X30
More informationINDEX TECHNICAL SPECIFICATIONS 2 SPECIAL TOOLS 3-4 PERIODIC MAINTENANCE 5 LUBRICANTS 6 TROUBLESHOOTING 7-14 TIGHTENING TORQUE TABLE 15
INDEX TECHNICAL SPECIFICATIONS 2 SPECIAL TOOLS 3-4 PERIODIC MAINTENANCE 5 LUBRICANTS 6 TROUBLESHOOTING 7-14 TIGHTENING TORQUE TABLE 15 ENGINE DISASSEMBLY 16-24 ENGINE REASSEMBLY 25-37 SPECIAL 3-SHOE CLUTCH
More informationPUSHING, BUMPING OR HITTING, IF INTENTIONAL YOU WILL BE BLACK FLAGGED & DISQUALIFIED. STOP IMMEDIATELY. Maintain position on track.
HELMETS ARE MANDATORY, NO EXCEPTIONS!! PUSHING, BUMPING OR HITTING, IF INTENTIONAL YOU WILL BE BLACK FLAGGED & DISQUALIFIED. STARTING PROCEDURE - Determined Race Day GREEN FLAG - RED FLAG - START OF RACE
More informationATV I l. l u. r a. Parts Manual ARCTIC CAT. 250 cc/300 cc
2000 I l l u st ATV 250 cc/300 cc Model No. A2000ATE2AUSG (250 - Green) Model No. A2000ATE2AUSR (250 - Red) Model No. A2000ATF2AUSG (300 2x4 - Green) Model No. A2000ATF2AUSR (300 2x4 - Red) Model No. A2000ATF4AUSG
More information334A or 334AB. Number of piston rings 1 Number of exhaust ports 2. Big end conr. Ball-bearing diam. 18X24X15 Combustion chamber shape Spherical
125cc LEOPARD FEATURES Cylinder volume 123.67 cc Bore 54 mm Max. theoretical bore 54.28mm Stroke 54mm Cooling system Water Inlet system Reed valve Number of carbs 1 Tillotson HL Carb. 334A or 334AB Cylinder/crankcase
More informationKWIK SHOP GENERAL PREDATOR RULES 2019
GENERAL PREDATOR RULES 2019 These rules are intended to keep the engine as Stock Out Of The Box as possible. There are no gray areas. If they do not specifically state that something is allowed, it will
More informationView Catalogs Online at
ML125-5 Frame Parts 12551-1 Grip, LH 12551-2 Front Brake Lever Comp. 12551-3 Handlebar Switch, LH 12551-4 Rearview Mirror, LH 12551-5 Rearview Mirror, RH 12551-6 Handlebar Switch, RH 12551-7 Clutch Lever
More informationMatchless G50 / Ajs 7R Seeley SMA BMW R 50 - R 69S SMA BMW RS 54 SMA BMW R5 R 51 R 66 Special parts on Inquiry. Pricelist
page 1 Pricelist 01.01.2018 SMA-Racing Industriestr.29 73340 Amstetten info@sma-racing.com Matchless G50 / Ajs 7R Seeley SMA BMW R 50 - R 69S SMA BMW RS 54 SMA BMW R5 R 51 R 66 Special parts on Inquiry
More informationHOFFMANN POWER PRODUCTS PARTS LIST 2014
HOFFMANN POWER PRODUCTS PARTS LIST 2014 HOFFMANN CHAINSAW PN7200 ALL PARTS ARE SUBJECT TO STANDARD HOFFMANN TERMS AND CONDITIONS OF SALE 2010 Replacement parts are not manufactured, sold or warranted by
More informationManufacturer Address Engine # IAME S.p.A. Via Lisbona, ZINGONIA (ITALY) X30 125cc RL-C TaG. Number of pages 22 PICTURE OF ENGINE
Manufacturer Address Engine # IAME S.p.A. Via Lisbona, 15 24040 ZINGONIA (ITALY) TAG RACING INTERNATIONAL TM Manufacturer IAME S.P.A. - ZINGONIA (I) Make PARILLA Model X30 125cc RL-C TaG Inlet type REED
More informationM.O.R.R. MOD KART RULES (EDITED APRIL 26, 2018)
M.O.R.R. MOD KART RULES - 2018 (EDITED APRIL 26, 2018) MOD KART CLASS: This class is represented by a 4-wheel race vehicle powered by a 400cc Honda Quad engine. It is designated for drivers ages 11-16
More informationNATIONAL HOMOLOGATION FORM KARTING ENGINE
NATIONAL HOMOLOGATION FORM KARTING ENGINE Manufacturer BRIGGS & STRATTON Make BRIGGS & STRATTON Model 206-124332 Validity of the homologation 6 years Number of pages 25 This Homologation Form reproduces
More informationToqua District Pinewood Derby General Rules
Toqua District Pinewood Derby General Rules WHEN: Saturday, May 6, 2017, 9 AM 12 PM. WHERE: Toyota of Knoxville Detail Shop (Across the street from the Showroom) 10415 Parkside Drive Knoxville, TN 37922
More informationINSTALLATION INSTRUCTIONS Horizon CCR HZ13054
INSTALLATION INSTRUCTIONS Horizon CCR HZ13054 IMPORTANT: PLEASE GIVE CUSTOMER ENCLOSED INFORMATION! Thank you for your purchase of our HeliBars. They are designed to increase your long distance comfort
More informationParts Lists - DB30 Qunshe Doodlebug 2.5hp Mini Bike (VIN PREFIX L4GS)
Page 1 of 7 Product Information Baja Web > Product Information > Parts Lists > MINIBIKE > DB30 Qunshe Doodlebug 2.5hp Mini Bike (VIN PREFIX L4GS) DB30 Qunshe Doodlebug 2.5hp Mini Bike (VIN PREFIX L4GS)
More informationG85CS Parts list. Frank Kyul, Netherlands
G85CS Parts list Frank Kyul, Netherlands http://home.wanadoo.nl/fxkuyl/ CYLINDER BARREL & HEAD 022298 Barrel Cylinder 1 022515 Washer Cylinder Base 1 015351 Nut. Sleeve Cylinder Head 4 042157 Washer Sleeve
More informationLANCO MICRO MIDGET AUTO RACING CLUB, INC Car Specifications
Date: 11/16/2017 These specifications provide the framework for LMMC officials to inspect racecar. In addition to interpreting and enforcing these specifications, LMMC officials are authorized to make
More information2018 HONDA CRF400R ENDURO
Press Release 2018 HONDA CRF400R ENDURO Press release date: 31 st July 2017 Press release date: New model: The CRF400RX Enduro is an all new product for the Honda lover! Developed from the CRF 450 RX Enduro
More informationWKA 2010 MANUFACTURER S CUP TAG SERIES REGULATIONS
WKA 2010 MANUFACTURER S CUP TAG SERIES REGULATIONS Contact information and updates can be found at www.ovka.com The following regulations are guidelines ONLY. Please refer to 2010 WKA Technical Manual
More informationBRIDGESTONE M 1)RCYCLES TUNING UP
BRIDGESTONE M 1)RCYCLES TUNING UP BRIDGESTONE MOTORCYCLES TUNING UP FOR COMPETITION CONTENTS Introduction... 4 Tuning up 350 GTR for Road Racing...,... 7 Tuning up 350 GTR for Scrambling... 10 Tuning up
More informationGENERAL RULES FOR ALL CLASSES Revised 8/30/2017
GENERAL RULES FOR ALL CLASSES Revised 8/30/2017 1. ALL drivers must be able to operate the tractor in a safe manner, be able to stop forward motion of their tractor at any given time with no assistance
More informationX4 (GREEN) (A2000ATF2AUSG) Page 1 of 80 AIR INTAKE ASSEMBLY
2000 300 2X4 (GREEN) (A2000ATF2AUSG) Page 1 of 80 AIR INTAKE ASSEMBLY 2000 300 2X4 (GREEN) (A2000ATF2AUSG) Page 2 of 80 AIR INTAKE ASSEMBLY Ref # Part Number Qty S/P/F Description 1 3570-001 1 /P Intake,
More informationSLP PIPE INSTALLATION INSTRUCTIONS #09-9 & # & NEWER POLARIS INDY 650 & RXL PIPE SET EFFECTIVE 6-92
Page 1 of 5 SLP PIPE INSTALLATION INSTRUCTIONS #09-9 & #09-10 1988 & NEWER POLARIS INDY 650 & RXL PIPE SET EFFECTIVE 6-92 READ INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL PIPE SET #09-9 (For stock
More informationCOMER SW80 TECHNICAL SPECIFICATIONS
COMER SW80 TECHNICAL SPECIFICATIONS Comer SW80 Toowoomba % LV Tech Spec 2017 Preamble: The following are the Technical Specifications for the COMER SW80 engine, as approved by the Australian Karting Association.
More informationSuperbike Kit
Superbike Kit www.spieglerusa.com sales@spieglerusa.com Mounting Instructions & Safety Instructions for Honda CBR 1000 RR ABS model year 2017 - Attention Important Safety Instructions: Thank you for purchasing
More informationBriggs & Stratton. World Formula & Modified World Formula. Tech Manual
Briggs & Stratton World Formula & Modified World Formula Tech Manual First Issued: May 22, 2007 Updated: January 2017 Jerry Mostek QMA Tech 2012 Quarter Midgets of America, Inc. WORLD FORMULA CLAIM RULE
More informationNC30 Listing. Please contact us if you cannot find what you require. To order please telephone or write to :
NC30 Listing Please contact us if you cannot find what you require To order please telephone 01424 426383 or write to : NC30 Club, PO Box 48, Bexhill on Sea, East Sussex, TN40 2WY or email sales@nc30club.co.uk,.
More informationSECTION 1 - CHASSIS 1.1 CHASSIS FRAME
5TH CATEGORY - HISTORIC RACING GROUP Nb APPROVED VEHICLE SPECIFICATION This form details the approved specifications of individual vehicle models in the 5th Category Historic car group. To be issued with
More informationMONOPOSTO RACING Class Specification Formula Vee REVISED March 2008
MONOPOSTO RACING Class Specification Formula Vee REVISED March 2008 VINTAGE FORMULA VEE (PRE-1970) These rules describe and specify Formula Vee racing cars as they raced in the 1969 racing season. This
More informationSpare parts for PVP 251 and 252 Motor Exchange rate: 7,42 Prices list 2017 Prices Prices
Spare parts for PVP 251 and 252 Motor Exchange rate: 7,42 Prices list 2017 Prices Prices Part no1 Description Qty1 in DKK in EURO 110 Crankcase right and left side for motor 251 1 131908,00 11874,39 112
More informationATV 90 UTILITY CALIFORNIA GREEN (A2008KUB2BCAG) Page 1 of 58 AIR INTAKE ASSEMBLY
2008 ATV 90 UTILITY CALIFORNIA GREEN (A2008KUB2BCAG) Page 1 of 58 AIR INTAKE ASSEMBLY 2008 ATV 90 UTILITY CALIFORNIA GREEN (A2008KUB2BCAG) Page 2 of 58 AIR INTAKE ASSEMBLY Ref # Part Number Qty S/P/F Description
More informationView Catalogs Online at
Catalog ML125-5 2015Edition ML125-5 Frame Parts 12551-1 Grip, LH 12551-2 Clutch Lever Comp. 12551-3 Handlebar Switch, LH 12551-4 Rearview Mirror, LH 12551-5 Rearview Mirror, RH 12551-6 Handlebar Switch,
More information2016 FIM CEV REPSOL Moto2 TM TECHNICAL RULES (UPDATED: )
2016 FIM CEV REPSOL Moto2 TM TECHNICAL RULES (UPDATED: 13-01-2016) 2016 FIM CEV REPSOL Moto 2 TM TECHNICAL RULES Contents 1. Engine 2. Intake & Fuel System 3. Fuel tank and hoses 4. Airbox 5. Fuel and
More informationMaster Part List SY250. Rev. 1
Rev. 1 1-1015 Frame 1 1 1 1 1-1017 Frame 1 2-1021 Guard, engine 1 1 1 1 1 1 3-1044 Foot Rest, right side 1 1 1-1045 Foot Rest, right side 1 - S1A-20202-00-00 Foot Rest, right side steel 1 1 4-1054 Foot
More informationPARILLA LEOPARD X TECHNICAL SPECIFICATIONS
PARILLA LEOPARD X30 125 VERSION 7 / 2013 UPDATED JULY 16 th, 2013 DOCUMENT UPDATE SCHEDULE It is certified that the updates listed below have been approved by the Australian Karting Association and have
More informationTwo sets pole position chickenhawk tire warmers, with stands for thermostats
2005 TZ250, 650 miles total, never crashed, raced twice. Beautiful red, black and white paint job, no scratches. This bike is as new. Motor has new crank, and top end installed VHM head, inserts listed
More information2019 Road Warriors. Shock claim rule will be $50. Any driver finishing in the top 3 may claim shocks from any car finishing in the top 3.
2019 Road Warriors Protest $350 top end/ $400 bottom end any engine combination Crate engine claim rule will be $3900. Any car finishing on the lead lap may claim any engine that finishes on the lead lap.
More informationNATIONAL HOMOLOGATION FORM KARTING ENGINE
NATIONAL HOMOLOGATION FORM KARTING ENGINE Manufacturer TORINI MOTOR CO., LTD. Make TORINI Model CLUBMAXX 210 (TC210) Validity of the homologation 6 years Number of pages 34 Homologation N This Homologation
More informationTechnical Presentation model
Technical Presentation 2013 model Presentation contents Introduction Engines Chassis Electrical Maintenance Summary Introduction Introduction 2013 RM-Z450/250 ENGINEERING TARGET 1.Meeting new FIM sound
More informationEVERYTHING THAT IS NOT AUTHORIZED AND PRESCRIBED IN THIS RULE IS STRICTLY FORBIDDEN
2.13 KTM RC CUP TECHNICAL SPECIFICATIONS The following rules are intended to permit limited changes to the homologated motorcycle in the interests of safety and improved competition between various motorcycle
More informationNATIONAL HOMOLOGATION FORM KARTING ENGINE
NATIONAL HOMOLOGATION FORM KARTING ENGINE Manufacturer TORINI MOTOR CO., LTD. Make TORINI Model TC250 (PREVIOUSLY TRE220) UPDATE Validity of the homologation 6 years Number of pages 35 This Homologation
More information