PLEASE READ THROUGH THE WHOLE WRITE UP BEFORE ACTUALLY USING IT!!!!
|
|
- Marybeth Gilmore
- 5 years ago
- Views:
Transcription
1 JDM power folding mirror switch install into stock USDM harness. By: Greg L., Zeke21 on twinturbo.net PLEASE READ THROUGH THE WHOLE WRITE UP BEFORE ACTUALLY USING IT!!!! This is how I was able to get the rumored the JDM switch wont work in the USDM z car phrase disproved. However, I am not responsible for what ever happens to you or your car. Please read this carefully and take you time. It took me about 2 hrs a day for about a week, 25 fuses, and a lot of patience to get this right. This write up should not take you nearly as long because you have directions. But do take you time it is worth it. Install time: 30 minutes (some general z car and wire knowledge) to an hour (no knowledge) Brief over view: My JDM mirror install consists of the following. *USDM mirror housing, this enabled me to not have to paint the housing. *USDM power heated mirror. Do note the JDM power folding mirrors do not have this option. *The insides of the mirror housing consist of the JDM mirror Bracket and Motor. *You must also use the JDM mounts, these I had to have painted to match the color of my car. Note: this will cause the mirrors to be off in sight perception. Please see the chapter on the mirror install for further possibilities of fixing this. *The stock adjustable suspension switch is also installed into the JDM main mirror panel. First we will begin with just the install of the JDM switch into the USDM harness. Please leave you USDM mirrors on you car. We need to make sure the conversion works properly with the USDM wire harness. Also note: You may need extra 10A fuse in the event that something does not work. Step 1. Pull the switch out. Stick a flat head screwdriver next the edge of the switch on the driver s side. Gently bend the screwdriver towards the drivers seat in order to 'pop' the switch out.
2 Step 2. Next unplug the harness from the switch. Read before doing the next few steps: Step 3 (Plug and Play). DO THIS IF YOU DO NOT WANT TO CUT THE WIRES! I recommend step 3 because it is cleaner and just looks sweet. However if you do not mind cutting them skip this step. Pull the yellow plastic clip off the back of the harness plug. Use the flat head screwdriver on the both sides of the yellow clip to pry off. Now you are going to need a small flat head screwdriver, something that will fit inside the holes on the harness plug. Look inside these holes and you will see a metal pin. Put the screwdriver underneath the metal pin (see pic) and push the screwdriver up. This should let the wire lose so you can pull it out on the other side of the wire. It is kind of tricky but it will work. Picture below was taken using a harness that had been cut. Yours will not be cut on the end.
3 YOU ARE GOING TO PULL EACH WIRE OUT ONE AT A TIME. You will first pull one wire from the JDM switch out and then one from the USDM harness. Then you will toss the JDM wire off to the side and replace it with the wire you pulled out of the USDM harness plug. You want to do this one at a time in order to follow my little chart. Important! Leave the two Green/Red and Green/Black wires on the JDM harness plug. Those two wires power the folding function. You have no choice but to spice into those. But leave them alone for now. Also if you have a Twin Turbo and still want to use the stock adjustable suspension skip to the bottom of this write up titled Keeping The Adjustable Suspension. We re only trying to get the normal function of the mirror control to work right. Skip to step 5. TT s skip to bottom section and then return to step 5. Step 4. (Cut em up) DO THIS STEP IF YOU PLAN ON CUTTING THE WIRE HARNESS! If you plan on cutting please use the male and female end splicing tabs. This will make switching the wires around easier in case that the wires for some reason do not match up. Splice the male end on the JDM wires and the female on the USDM wires. Follow my chart, Step 5. Step 5. The Chart. This chart should be pretty self explanatory. However, look over the wire colors. If you do not have the same set of wire colors listed here, this conversion may not work. Wire colors are represented here by the main color first and then the stripe color on the wire if it should have it. For example:
4 Yellow (main color) / Black (stripe color) Work you way from left to right on my chart. For example take the Green wire and plug it into the spot that the Blue/White wire was in on the JDM plug. If you choose to splice, then splice the Green wire into the Blue/White wire. Note: Be prepared to have extra 10A fuses ready in case this wire conversion does not work. Don t worry hooking these things up wrong did not seem to hurt my car. I went through 25 of these bad boys trying to figure this out. If the fuse should go out: go to the fuse panel underneath the dash. It is located next to the footrest and the clutch. On the trim, slide the door up and replace the fuse. Stock (USDM) Harness JDM Harness Plug or Splice into these wires Green Yellow/Black Blue/Black Blue/Red Yellow/Blue Purple/White Blue/White Blue/Black Blue/Orange Blue/Red Blue/Yellow Blue Now after getting all your wires plugged or spliced in turn the car to the on position and try to adjust the mirrors. Make sure every direction works properly. If everything works then you have successfully completed the hardest part of the job. Well maybe not now that you had a chart to follow! However, if while trying to move the mirrors around and you heard a pop sound or nothing is working anymore, then the fuse has blown. Take you key out and replace the fuse. Now you are going to have to go through some trial and error. If this is the case me. *Keeping The Adjustable Suspension For those that have a Twin Turbo and still have the stock adjustable suspension read the following: The JDM mirror switch does not have the sport/touring switch on it. However don t despair, we can put ours in it. Notice the blank spot on the left of the switch were the sport/touring switch would be normally, well that piece comes out. Step1: You need to separate the top from the bottom of both the USDM and JDM switch. They separate the same way. Look along the edge of the switch and you ll notice 4 notches in which the top of the switch comes over a square piece of plastic, which is attached to the bottom. You will need to take a small screwdriver and bend the plastic
5 from the top up over those square pieces attached to the bottom. It is a little tricky but once you get one side it easily comes off. Be careful though because it is thin plastic and can break. When completely separating the top from the bottom, separate the two while keeping the top in one hand the bottom it the other and then tilting the bottom vertical (straight up) again so the contacts will not fall out. Once open some small plastic white pieces will be loose. Those are the contacts, which are guided by the switch over the circuit board. The circuit board also has some jelly substance on it so don t get your fingers in it. Set the bottom portions and the contacts aside for now. contact is the center white piece. The sport/touring one is missing in this pic but should be in yours. Step 2: Take your stock USDM switch and look at the side of the switch with the sport/touring switch facing you. You ll see a small little circular metal thing. This is a long narrow metal pin that holds the rocker switch in place. Take a screwdriver that is small enough to fit inside of it. Look for the edge of the metal pin; meaning it was a flat piece of metal rolled so it has a separator point. Once you locate it put the edge of your flat head screw driver inside of on that point and continue to pull down on that area while pulling towards you. This will take some time.
6 However if you are having trouble doing this I also found that using a small drill bit and a power drill and setting it in reverse while pulling back on it will also bring it out, as long as the drill bit is big enough to fulfill the whole circular area. Once it is out it will look like this: Step 2: Take your screwdriver or a straightened paper clip and stick it into the bottom of the switch and push the rocker switch out from the bottom.
7 Step 3: Now follow step 1 and 2 for the JDM switch. Except this time you will push out the blank panel. Step 4: Drop the USDM rocker sport/touring switch into the JDM main switch panel. Once in it will either be forward or backwards in direction, there is no middle setting remember. So once in one of those directions simply push that metal pin you took our back in. This will lock the rocker switch in place.
8 Step 5: Remember to remove the white plastic square piece from the USDM switch that was found on the rocker switch and put it into the same place on the JDM switch. Step 6: Now put the bottom of the switch back on by snapping it into place. Step 7: Now go to the mirror switch wire harness again and you are going to add one wire for the sport/touring switch harness. Here you will simply put your leftover wire into the bottom left hole when the plug harness is facing you. See pic.
9 Step 8: Once you put the wire in simply plug the harness into the switch and put it into the center console. And remember to test it to see if it works. If it does not try switching the wire location you did in step 7 to the top and see if that works. Do realize that the JDM switch does not have the letter for the sport/touring rocker switch. I looked into moving just the folding mirror switch into the usdm top switch housing and keeping the bottom of the jdm circuit board but so far have had not luck. I pulled my sport/touring rocker switch out of a switch from an early year z, which had the mirror defrost button on it in place of the folding mirror switch. However, although they look the same on the surface when you get inside they are completely different in how they are built and thus make it impossible to swap. However, there is a chance that if I get a later year z mirror switch from a 95 or 96 and those are built without the mirror defrost button internals ( I know these years did not have the button but Nissan may have just keep the bottoms the same and just pluged the rocker switch area) them maybe I can swap in the manner just mentioned. But until I have a spare 50 bucks or more to spend on a new switch this one works fine without the print.
10 All done and return to step 5 Coming soon, Part 2: The install of the mirrors on the car while keeping the power defrost option and running power folding wires to the mirrors.
Installing the Wireless Charging upgrade kit in a 2018 XT5 (Platinum version)
Installing the Wireless Charging upgrade kit in a 2018 XT5 (Platinum version) September 2, 2018 Tools needed: Wireless charger upgrade kit Plastic trim tools 7 mm nut driver Background: I purchased the
More informationTutorial:Head Unit Installation
Tutorial:Head Unit Installation From Tech Wiki : Nissan 350Z : Infiniti G35 : Nissan GT-R Here, I installed the Kenwood DDX7015 touch screen DVD system. I made this step-by-step tutorial to help those
More informationConnecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod
Connecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod DISCLAIMER: I'm human and make mistakes. If you spot one in this how to, tell me and I'll fix it This was done on my 99.5 Jetta.
More informationWe will be upgrading from the factory, paper-cone disgrace to an Infinity Kappa 62.9i:
In order to fully round out your stereo upgrade, the factory rear speakers must go. This is another easy job to tackle, but the fitment of the package tray and being hunched over in the rear glass area
More informationMustang CDC Lightbar (94-04) - Installation Instructions
Mustang CDC Lightbar (94-04) - Installation Instructions The below installation instructions work for the following products: Classic Design Concepts Mustang Convertible Lightbar (94-04 Carbon Fiber) Classic
More informationFanatec GT3RS V1 to GT3RS V2 Tutorial
Fanatec GT3RS V1 to GT3RS V2 Tutorial by Roy Visser 1 How to update your Fanatec GT3RS V1 wheel to a GT3RS V2 wheel Welcome to this guided and detailed tutorial for upgrading your Fanatec GT3RS V1 wheel
More informationSTEPS FOR REMOVING REAR ASHTRAY & CUP HOLDER, CENTER ARMREST, E- BRAKE CONSOLE, FRONT ASHTRAY, LOWER CENTER CONSOLE AND GLOVE BOX
Please give credit where credit is due! This DIY was completed ENTIRELY by the hardest working VW Vortex moderator on the site!! Gary Thompson, Ph.D. - vortex ID VGRT6, email address vgrt6@yahoo.com. Please
More informationConvenience Lighting
Convenience Lighting by Flopster843 19 Dec 2011 In order to cut costs and make a larger profit, many automobile manufacturers decided to cut several minor items from the production line. Chrysler removed
More informationStand Alone Fog Lights Installation Instructions
Tools Required: 1. Trim Removal tool or protected flat screwdriver 2. #2 Phillips Screwdriver 3. 10mm socket 4. 10mm wrench 5. 8mm or 5/16 socket 6. Adjustable Pliers 7. Electrical Tape WARNING!!! Disconnect
More informationSingle Barrel Shotgun HPFP Install Guide
Single Barrel Shotgun HPFP Install Guide Thank you for purchasing the VTT Single Barrel Shotgun HPFP upgrade kit! PLEASE READ THE ENTIRE GUIDE BEFORE BEGINNING INSTALLATION! The first thing you should
More informationFitting the Bell Auto Services (B-A-S) TDV6 EGR Blanking Kit to a 2006 model Discovery 3 TDV6 HSE
Fitting the Bell Auto Services (B-A-S) TDV6 EGR Blanking Kit to a 2006 model Discovery 3 TDV6 HSE Before I describe how I did this, I must first thank other members of the Disco3.co.uk forum (namely J,moore
More informationCurt Mfg. Trailer Hitch and Hoppy Wiring Kit Installation Instructions
Curt Mfg. Trailer Hitch and Hoppy Wiring Kit Installation Instructions The Curt trailer hitch replaces the stock rear cross member in the Touareg. It attaches with 8 bolts just like the factory VW hitch.
More informationDoor Panel Removal & Window Stop Adjustment
Door Panel Removal & Window Stop Adjustment By: Jeff Wolford Disclaimer: This is simply an article of how I fixed my car. I m not responsible if you break, scratch, or mess up anything following my example.
More informationRaxiom Factory GPS Rear Back-up Camera Kit (07-17 Wrangler)
Raxiom Factory GPS Rear Back-up Camera Kit (07-17 Wrangler) Installation Time: 2.5-3Hrs Tools Required: 7mm Socket & Driver 10mm Socket 10mm Open end wrench Knife / Razor blade Zip-ties Wire Cutters Needle
More informationInstallation Instructions Jeep CJ-7
Retrofit Steering Column Installation Instructions 1976-86 Jeep CJ-7 For Part # s 1520800010, 152800020, 1520800051 www.ididitinc.com 610 S. Maumee St., Tecumseh, MI 49286 (517) 424-0577 (517) 424-7293
More informationIntake Kit Supplement for CRV and Pathfinder
Intake Kit Supplement for CRV and Pathfinder This guide will briefly outline how to install the intake kits for the Honda CRV and Nissan Pathfinder. This is a pretty basic job, but for the average person
More informationSunroof Repair. Sunroof Repair TSB. The sunroof repair kit available for the J30 is part number Y20. See images at bottom of document.
Sunroof Repair This document is the text/images from the TSB (technical service bulletin) issued by Infiniti concerning the repair procedure for sunroof issues. Be advised that this is a LARGE, TIME-CONSUMING
More informationOEM Cruise Control Installation in GMC/Chevy NBS trucks
OEM Cruise Control Installation in 99-02 GMC/Chevy NBS trucks May 2008 ~ Rampage_Rick Having just installed factory cruise control in my 00 Sierra, I thought I d share the fun. I followed the steps outlined
More information2010 Toyota Prius model II Head Unit Upgrade
2010 Toyota Prius model II Head Unit Upgrade Monday, December 21, 2009 Disclaimer: Use this document and its contents at your own risk. Forward: Huge thanks to those members on Priuschat.com that forged
More informationAnother CJ picture guide to replacing the key cylinder in a non-tilt steering column
Another CJ picture guide to replacing the key cylinder in a non-tilt steering column by John Strenk Well I'm sure it's happened to all of us one time or another. You park your jeep and go to turn off your
More informationAnother CJ picture guide to
Another CJ picture guide to replacing the key cylinder in a non-tilt steering column by John Strenk Well I'm sure it's happened to all of us one time or another. You park your jeep and go to turn off your
More information4TH GEN SEATS IN A 3RD GEN TRUCK
4TH GEN SEATS IN A 3RD GEN TRUCK by Flopster843 02 Oct 2016 If you drive a 3rd generation Dodge Ram truck, I am sure you have discovered that the OEM seats are not the greatest (Figure 1.) They are extremely
More informationInstallation Instructions
Installation Instructions Jeep JK Unlimited (2007 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Bracket for ARB Compressor
More informationBMW 2002 M42 Swap Notes-THIS IS NOT FINISHED
BMW 2002 M42 Swap Notes-THIS IS NOT FINISHED This document is to help those that want to install an m42 into a BMW 2002. It is based around an e30 engine, trans, and wiring. You can use the e36 block/head/wiring
More informationwww.odometergears.com Mercedes-Benz Mechanical Odometer Repair This how to can be used for all mechanical repairs as the only difference will be the removal of the instrument cluster. http://www.dieselgiant.com/repairyourodometer.htm
More informationImproving the gearshift feel in an SW20.
Improving the gearshift feel in an SW20. Part one In 3 parts. The SW20 gearshift can be often be greatly improved by eliminating play in the shift linkages, and this article covers three areas that need
More informationJRSC + BBK Install on SVTF. Neil A. Shah medicnas on focaljet September 2006
JRSC + BBK Install on SVTF Neil A. Shah medicnas on focaljet September 2006 ECU up here. When removing make sure the smaller bundles of wires don t get wrapped around the bottom edge and break - this almost
More informationRetro it Steering Column
Retro it Steering Column INSTALLATION INSTRUCTIONS for 1976-86 CJ5 & CJ7 FOR PART NUMBER S: 1520800010, 1520800020, 1520800051, 1526800010, 1526800020, 1526800051 S I NCE 1986 Instruction # 8000000010
More informationShotgun Single Barrel HPFP install guide
Shotgun Single Barrel HPFP install guide Thank you for your purchase of the VTT Shotgun Single Barrel HPFP upgrade! First thing to do when you open your box is to make sure all parts are in their respective
More informationMustang Clutch Cable Installation Guide 96-04
Mustang Clutch Cable Installation Guide 96-04 The below installation instructions work for the following products: Steeda Adjustable Clutch Cable 96-04 Maximum Motorsports Clutch Cable 82-04 Steeda Clutch
More informationSome tips and tricks I learned from getting clutch out of vehicle Skoda Octavia year 2000
Some tips and tricks I learned from getting clutch out of vehicle Skoda Octavia year 2000 Last change 2013-Oct-11 I bought Haynes manual for a starter. That s something well worth it s cost I believe.
More information2000 Mr2 Spyder Seat Cover Replacement Project
2000 Mr2 Spyder Seat Cover Replacement Project Tool List: Plastic Trim Tool, Hog Ring Pliers, Medium or Heavy Duty Wire Cutters, 12mm socket, 14mm Socket, Ratchet, Extension, Flat Head Screwdriver & Gloves
More informationOur goal is to make the install a breeze. Please read the entire guide before beginning.
www.airkewld.com Page 1 of 6 IRS Axle Kit Install IRS Axle Kit Install Our goal is to make the install a breeze. Please read the entire guide before beginning. KITS SHOULD INCLUDE 2 - Control-arm mounting
More informationHow to Replace the B2 Piston Bore Seal
Page 1 Home Cars for sale Trucks for sale Where we are Links to other diesel sites About us Why diesel? Diesel Videos How they work How they sound FAQ Dodge Diesel Maintenance tips, parts and DIY DVD's
More informationC4 Sound Deadening & Insulation Kit Interior Removal & Installation Instructions
C4 Sound Deadening & Insulation Kit Interior Removal & Installation Instructions Ok, let's start with taking the radio bezel dash area off first. Here is what the OEM radio looks like, and the points you
More informationInstallation Directions for FINGER STICK and Blocker Plate
Installation Directions for FINGER STICK and Blocker Plate What is a Finger Stick? A Finger Stick is a simple circuit that modifies the MAF signal on LLY and LBZ engines (not LB7 engines) to expected levels
More informationRedlineGoods Tacoma Installation Manual
RedlineGoods 2016+ Tacoma Installation Manual AUTOMATIC SHIFT BOOT AND EBRAKE BOOT Press down on the factory shift boot collar to disconnect it from the shift knob. Unscrew shift knob Pull up on the rear
More informationTrouble Shooting Guide for Hubbell Systems
Trouble Shooting Guide for Hubbell Systems NOTE: Hubbell Special Products discontinued operations in 2008, so there is a very limited number of repair parts available for motor repair. In some ways, this
More informationInstallation Instructions
Installation Instructions Jeep JK 2-Door (2011 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Flat Bracket 1 Formed Bracket
More informationTroubleshooting Guide for Okin Systems
Troubleshooting Guide for Okin Systems More lift chair manufacturers use the Okin electronics system than any other system today, mainly because they re quiet running and usually very dependable. There
More information*Some speedometers have these additional electronic connections. If yours does, then remove the smaller slotted screws shown.
www.odometergears.com 1981-1985 240 Cable-Driven Speedometers (NOT for 1986 and later electronic units) http://www.davebarton.com/240-odometer-repair.html For this set of instructions below, I will not
More informationInstalling Custom Puddle Lamps 2009 Subaru Forester
Installing Custom Puddle Lamps 2009 Subaru Forester By John Perkins This guide will assist you in installing a set of LED puddle lamps on a 2009 Subaru Forester. This is NOT using the $150 Subaru kit.
More informationHOW TO REPLACE THE SPOILER ON YOUR GEN 3 PRIUS
HOW TO REPLACE THE SPOILER ON YOUR GEN 3 PRIUS Yup, it happened. The spoiler on your beloved Prius has departed this earth and now is in the great junkyard in the sky. This is how you make it all better
More informationX-Type w/ non-premium sound amplifier installation instructions
X-Type w/ non-premium sound amplifier installation instructions 1. Pull radio from dash (see Radio Removal Instructions ) 2. Disconnect wiring harness from back of radio by pushing in tab on plug and pulling
More informationHasse Mods for the Ampeg J20 Guitar Amp
Hasse Mods for the Ampeg J20 Guitar Amp The following is adapted from a post I put up on The Gear Page, in the Amp Techincal forum. It shows the mods I did to my Ampeg J20. Okay, here s my mods for this
More informationFitting Instructions For The TDV6 EGR Blanking Kit To A 2006 Model Discovery 3 TDV6 GHSE
Part Number DA1112 Fitting Instructions For The TDV6 EGR Blanking Kit To A 2006 Model Discovery 3 TDV6 GHSE You do this modification at your own risk. Britpart won t be held responsible for what is written
More informationRemove the 3-11mm nuts holding mirror on. Don t drop the nuts!
2005-2012 Ford Mustang Puddle Lamp Kit Parts List: Quantity: Tool List: LED Lamps 2 Flat head screwdriver Seals 2 Ratchet & Socket set OR Nuts 2 Adjustable Wrench Wiring harness 1 Drill & 11/16 th bit
More informationHow I installed new brake pads on my i with Sport Package (should be fine for other E39 s) By Robert B.
How I installed new brake pads on my 1999 528i with Sport Package (should be fine for other E39 s) How I installed new brake pads on my 1999 528i with Sport Package (should be fine for other E39 s) By
More informationTools needed: Here is a pic of the shift kit I used. It is a Transgo brand and as you can see, it just a bag full of springs and one valve.
Before installing a shift kit, be sure the transmission is in good operating order. If your transmission is making noises, slipping, shifting bad or the fluid looks brown or smells burnt, take the transmission
More informationVolvo 1800 Dash Pad Replacement
Volvo 1800 Dash Pad Replacement (courtesy of John Garden State Chapter Volvo Club America) Reupholstering the dash Well it has been some time since I have been online in the forum. Winter is a quite time
More informationChanging the Struts on a WK Jeep CRD
Changing the Struts on a WK Jeep CRD Step by Step By Chirpz Disclaimer: I do not claim that this procedure is the right way or even the best way to change your struts. This is what I did after reading
More informationPT 709 firing pin and extractor removal. Disclaimer: My Taurus manual says not to take this apart (just flush it with cleaner).
PT 709 firing pin and extractor removal. Disclaimer: My Taurus manual says not to take this apart (just flush it with cleaner). But several list members have done this without ill effect. So here goes:
More informationTroubleshooting Guide for Limoss Systems
Troubleshooting Guide for Limoss Systems NOTE: Limoss is a manufacturer and importer of linear actuators (motors) hand controls, power supplies, and cables for motion furniture. They are quickly becoming
More informationINSTALLATION OF A WARN M8000 WINCH IN A HIDDEN MOUNT ON THE 2001 EXPLORER SPORT TRAC
INSTALLATION OF A WARN M8000 WINCH IN A HIDDEN MOUNT ON THE 2001 EXPLORER SPORT TRAC By: Kyle Schwulst Email: bigmellon@yahoo.com BACKGROUND I have always wanted a winch on my vehicle. There is just something
More information2015 Copyright Maxspeed-Motorsports.com
1 Porsche PCM 3.1 Backup Camera Installation Instructions. Thank you for purchasing your product at www.maxspeedmotorsports.com Before you start please understand that these installation instructions are
More informationAn Actual Driving Lesson. Learning to drive a manual car
An Actual Driving Lesson Learning to drive a manual car Where are the controls that I might have to use in my driving: Knowing where the controls are, and being able to locate and use them without looking
More informationML63AMG appartiens à un membre de mbworld.org merci. W210 E Class Folding Mirror Modification
ML63AMG appartiens à un membre de mbworld.org merci W210 E Class Folding Mirror Modification Originally installed in 2002. Revised write up completed September 5, 2013. Step 1 - New Switch and Wiring Harness
More informationPrerequisites: Shop Manual (recommended) pages 3-9 through 3-13.
Prerequisites: Order your gaskets average about $25.00 bucks X 2 so $50.00 4NK-11193-00-00 Obtain a shim kit (Should have several 265 and 270s) (Some dealers will exchange) Obtain a Valve Bucket Tool YM-33961
More informationHow to install the Barnett clutch and the stronger Oil Pump Drive Gear
How to install the Barnett clutch and the stronger Oil Pump Drive Gear Written by WildFred I m from Germany so please excuse my English and the spelling. The following procedure is a combination of the
More informationProjector39/Umnitza BMW Headlight & Re-Installation for E39s Predator Angel Eyes, and Lamin-X Installation
Projector39/Umnitza BMW Headlight & Re-Installation for E39s Predator Angel Eyes, and Lamin-X Installation Now it is time to remove the headlights! Obviously you have to open the hood to do this. 100_3630.jpg
More informationDrVanos.com Stage II Installation Instructions. Tool rental is available with the purchase of a vanos kit *See website for more info*
DrVanos.com Stage II Installation Instructions Special Tools Needed: Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for
More informationRear Speaker replacement.
Rear Speaker replacement. First off you need the right rear speakers. The easy bit is 6x9 and better than a 15W paper cone, the difficult bit is getting a mounting depth under 74mm. Or to be more precise,
More informationDoor panel removal F07 5 GT
Things needed Decent plastic trim removal tools Torx 30 Spare door clips 07147145753 I got away with a set of 5 but if I did it again I d be cautious and get 10. From prior experience if they are damaged
More informationBMW E61 Hydraulic Pump replacement instructions
BMW E61 Hydraulic Pump replacement instructions This DIY will guide you through the tasks needed to successfully replace your defective tailgate hydraulic pump Difficulty 3 of 10. The most difficult part
More informationSMART LAB PUTTING TOGETHER THE
PUTTING TOGETHER THE SMART LAB INSTALLING THE SPRINGS The cardboard workbench with all the holes punched in it will form the base to the many cool circuits that you will build. The first step in transforming
More informationModdit. How to Install Stance Coilovers on a Subaru
Moddit How to Install Stance Coilovers on a Subaru BRZ Let's get LOW (and maybe lighter and stiffer suspension)! In this article, we will install Stance ST- ZN6-XS Coilovers on the FRSport Subaru BRZ.
More informationGreddy E-manage Installation and Tuning Information
Greddy E-manage Installation and Tuning Information Overview The Emanage has a lot of functionality considering it is still a piggyback type engine management system and not a full standalone. By itself,
More informationShotgun Double Barrel HPFP install guide
Shotgun Double Barrel HPFP install guide Thank you for your purchase of the VTT Shotgun Double Barrel HPFP upgrade! First thing to do when you open your box is to make sure all parts are in their respective
More information2007 Crown Victoria Police Interceptor (P71) Blend Door Actuator Replacement (If I did it, you can too.)
2007 Crown Victoria Police Interceptor (P71) Blend Door Actuator Replacement (If I did it, you can too.) I'm not saying this is the only way, or even the right way, but it worked for me. First time I've
More informationLincoln Mark VII T5 Swap Version submitted by 5.0 bird
Lincoln Mark VII 1984-1989 T5 Swap Version 20070611 submitted by 5.0 bird I've decided to make an article to assist with the T5 swap for the 84-89 Mark VIIs, since I was just in there because my DOA didn't
More informationSteeda Sport Mustang Lowering Springs (2005+) - Installation Instructions
Steeda Sport Mustang Lowering Springs (2005+) - Installation Instructions The below installation instructions work for the following products: Steeda Sport Mustang Lowering Springs (2005+) Please read
More informationDIY: Repairing/Replacing the Timing Chain Tensioner
DIY: Repairing/Replacing the Timing Chain Tensioner By Saki GT - February 8, 2012 [youtube=http://www.youtube.com/watch?v=24cil5_9yvq] The above video is an example of how a bad Timing Chain Tensioner
More informationM62 Alternator Removal / Replacement (Water Cooled)
M62 Alternator Removal / Replacement (Water Cooled) Pre-Steps 1. Disconnect Battery Positive lead 2. Charge Your Battery with battery charger to full charge (So you new alternator wont have to work as
More informationInstalling AMP-wiring in a New Beetle
Installing AMP-wiring in a New Beetle Vehicle used: New Beetle 2.0i Type 9C (1999) Used set of cables: Dietz 35mm² power cable, double shielded Dietz chinch cable ( 35mm² Professional Line ) First of all:
More informationHard Bar Sport, M1/M2 Hard Core Hardtop, M2 Sport, and Xtreme Installation Instructions
HARDWARE KIT: Hard Bar Sport, M1/M2 Hard Core Shoulder Harness Guide Relocation Assemblies: 2-3/8" X 1" grade 8 bolts 4-3/8" flat washers 2-3/8" lock nuts 2 - brass bushings 2 - plastic trim caps 2-3/8"
More informationAamir_bt The legend..
Aamir_bt The legend.. How to do timing on a 4XE1-W (DOHC) engine. well i decided to to a write up for DOHC timing since there was only the SOHC written up, and i had to do a timing belt on my stylus anyways,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Model: 8510 & 8510TK Ford E Series Van 1994 2002 with stock power mirrors Tools required for the installation are: 7/16 socket, T20 screwdriver or 8mm socket, screwdriver, phillips
More information4 pieces of silicone hose Unless you have AEM then you have 2 2.5, 1 3, and 1 3.5
The parts in your kit: 3 pieces of Mandrel-Bent Aluminized Tubing: 1 Straight 1 45 degree bend with straight section 1 curved section 4 pieces of silicone hose 1 2.5 1 3.5 2 3 Unless you have AEM then
More informationThis write-up is subject to revision. PM me, eb2143 at tdiclub.com and I will update it if there are inaccuracies, typos, missing information, etc.
1 A4 Door Switch Replacement, 1.0 Notes on this guide: The following guide is mostly a combination of two write-ups by VgRt6 on Vwvortex.com. Specific threads located here: http://forums.vwvortex.com/showthread.php?1015107
More information72 Mustang Mach 1 tachometer cluster and gauge conversion
72 Mustang Mach 1 tachometer cluster and gauge conversion Dated: 02-17-2009 (drafted by a Chevy person working on his first Ford -not good-) Revised: 11-05-2010 The following information pertains to how
More informationNow we re ready to install our new mounts. The picture on the right shows our old and new for comparison.
Well I didn t have a chance to write last week so we have a little catching up to do. Last Sunday I started out with setting up a jig to weld in the mounts. The jig is made out of a old fork tube that
More informationMustang Radiator Conversion DIY. By GearHeadPeter. January 27, 2011
1964-1966 Mustang Radiator Conversion DIY By GearHeadPeter January 27, 2011 We all know that the radiators in our cars are not the best, especially if you have done any customization to the engine, which
More informationMAX FLOW FUEL KIT KIA FORTE SX HYUNDAI VELOSTER TURBO INSTALLATION INSTRUCTIONS
MAX FLOW FUEL KIT KIA FORTE SX 2014+ HYUNDAI VELOSTER TURBO INSTALLATION INSTRUCTIONS Installation: Tools needed: 1/4 or 3/8 drive ratchet Different length extensions 8mm socket / 10mm socket / 12mm socket
More informationINSTALLATION INSTRUCTIONS JEEP 2011-UP JK SECURITY FULL CONSOLE #274
INSTALLATION INSTRUCTIONS JEEP 2011-UP JK SECURITY FULL CONSOLE #274 PARTS CHECKLIST Tuffy Console #9 Left Front Mounting Bracket #10 Right Front Mounting Bracket #11 Electronics mounting bracket #12 Divider
More informationv Porsche 928
1985-86 32v Porsche 928 Toll-Free Tech Hot Line: 877-FOR-928M 877-367-9286 Please do not copy this manual and give copies to your friends. Our ability to bring you this supercharger kit at this price relies
More informationGruvenParts.com BRASS GM Power Folding Mirror Gear Replacement Instructions. Updated 8/25/2017 Additional Pictures / Tips Posted!
Page 1 GruvenParts.com BRASS GM Power Folding Mirror Gear Replacement Instructions Updated 8/25/2017 Additional Pictures / Tips Posted! ** Latest Design is uses an ALL BRASS SPUR GEAR!!! ** ** If you don
More information2010 Toyota Prius Fog Light Retrofit
2010 Toyota Prius Fog Light Retrofit A DIY prospective Last updated: Friday, December 25, 2009 *** Disclaimer Use this document and its contents at your own risk! *** Forward: This document was compiled
More informationPeg-Harness installation instructions
Peg-Harness installation instructions I know it s not the easiest thing to do, but PLEASE READ THESE INSTRUCTIONS COMPLETELY so you will understand what you are trying to accomplish before you start drilling
More informationDisco 3 Clock Spring / Rotary Coupler replacement
Disco 3 Clock Spring / Rotary Coupler replacement I recently had to change my Clock spring and thought some folks may find it helpful to see what it entailed. I did lots of reading around but couldn t
More informationAutomatic trunk lid retrofit BMW F10 Bj.2011 by laser21 bimmerfest.com
Automatic trunk lid retrofit BMW F10 Bj.2011 by laser21 bimmerfest.com lukasko@gmail.com This is a short guide to help you retrofit the option SA316 - automatic trunk lid mechanism into your F10. That
More informationInstallation Tips for your RS-1 + Honda-SL3 (1.b) Remote starter Honda: ( FIT), ( Pilot), ( Ridgeline) Acura: ( MDX)
Installation Tips for your RS-1 + Honda-SL3 (1.b) Remote starter Honda: ( 06-08 FIT), ( 05-08 Pilot), ( 06-13 Ridgeline) Acura: ( 03-06 MDX) TIP SHEET T0777 Thank you for purchasing your remote start from
More informationInstallation Tips for your Crimestopper/ProStart Remote Start system (add-on for GM vehicles) v1.02 updated 1/16/2013
Installation Tips for your Crimestopper/ProStart Remote Start system (add-on for GM vehicles) v1.02 updated 1/16/2013 Thank you for purchasing your remote start from MyPushcart.com - an industry leader
More informationEURO HEADLIGHT ADJUSTER REMOVAL AND INSTALLATION
EURO HEADLIGHT ADJUSTER REMOVAL AND INSTALLATION This document is a step by step explanation of how to remove and replace the headlight adjusters in the Euro headlights. Parts needed to repair both headlights:
More informationYOU MAY WANT TO FIRST TRY TO LOOSEN THE FILTER HOUSING
2005 XC90 Tune-up (5-cyl) Including: Oil Change - Spark Plugs - Fuel Filter - Cabin Filter First off - let me say that I am an amateur (at best) mechanic, and I claim no responsibility for whatever you
More informationBMW 528i E39 Sunroof Repair
These instructions will help guide you through the repair process for broken sunroof control rails on an E39 chassis. Before I get started, I want to give a shout-out to a couple people who also posted
More informationInstallation Tips for your Remote Start system (for Toyota Camry & Prius C, ) Crimestopper RS0+ EVO-ALL T3468 rev#1.
Installation Tips for your Remote Start system (for Toyota Camry & Prius C, 2012-2014) Crimestopper RS0+ EVO-ALL T3468 rev#1.1 1/22/2015 Thank you for purchasing your remote start from MyPushcart.com -
More informationPorsche 928 with 16v LH-Jetronic Fuel System
Porsche 928 with 16v LH-Jetronic Fuel System Toll-Free Tech Hot Line: 877-FOR-928M 877-367-9286 Please do not copy this manual and give copies to your friends. Our ability to bring you this supercharger
More informationInstructions for Front Midrange / Tweeter Installation in BMW 3 Series/M3 (E36)
Disclaimer: Bavarian Soundwerks highly recommends professional installation of the products we sell. We provide these installation instructions free of charge as a guide to assist those customers who choose
More informationPDC RETROFIT INSTALLATION By Kevin
1 PDC RETROFIT INSTALLATION By Kevin Kshek369@hotmail.com 1 These instructions are intended to help those who chose to do this retrofit by showing you what you are in store for and to give you some instructions
More informationI want to try my hand here at doing a TacoBill write up so here it goes.
Here is part 3 of my tutorial for the conversion of my Shaker 1000 to the Kenwood DNX7100 Navigation / Head Unit. With the 7100, my new system will include the Kenwood I-pod Adapter (P.I.E. KNW/USB-AV),
More information