Completion Tools Catalog

Transcription

1 Completion Tools Catalog TEAM Oil Tools. All rights reserved.

2 TEAM Oil Tools. All rights reserved.

3 TABLE OF CONTENTS P/N Description Page P/N Description Page Retrievable Packers Seal Bore Packers T107 T405 T412 T421 T436 T437 T440 T441 T442 T444 T456 T600 T600 T603 T607 T611 T628 T629 T631 T636 T641 T650 T654 T658 T900 T901 T905 MCA Valve H Tension Packer SL Tension Packer GV-5 Gas Vent Packer C-1 Tandem Tension Packer S-1 Tandem Tension Packer Casing Packer WS Hanger Packer V.I.P. Gas Vent Packer System CS Compression Packer M-2 Shear Tension Packer ASI-X ion Packer ASI-X 10k ion Packer ASI-X HP ion Packer Patriot Packer ASII Compression Packer AS-5 Anchor Packer AS-6 Anchor Packer AS-3 Single Grip Packer Snapset II Compression Isolation Packer Compression Isolation Packer HS-1 Hydraulic Prod. Packer HS-4 Isolation Packer HSR-4 Hydraulic ion Packer MSV Dual Compression Packer R-2 Dual String Tension Packer HS-II Hydraulic Set Dual String Packer T265 T670 T671 T674 T678 T1125 TEAM Pack TL Perma-Packer Bore Packer JL Perma-Packer Bore Packer Hydro Perma-Pak DB Perma-Pak Scorpion Packer Tubing Anchors T312 T354 Accessories T510 T512 T513 T568 T569 T572 T585 T597 T598 H/D Tubing Anchor Catcher RT Anchor Catcher T-2 On/Off Tool Stinger T-2 On/Off Connector T-2 Type H On/Off Tool RH Rotational Safety Joint Model K Shear Safety Joint Telescoping Swivel Joint PBR Packer Tubing Accessories Wireline Adaptor Kit Drillable Tools VIPER II Composite Bridge & Frac Plug Data Charts Elastomer Guide TEAM Oil Tools. All rights reserved

4 M.C.A. Valve The T107 MCA Valve is used with the T440 Casing Packer to cement liner strings into the well bore or open hole. The casing packer is set in compression allowing the MCA Valve to shear at a pre-determined value, opening the cementing ports. The cementing ports are closed by straight pick up on the casing string. Available in premium thread connection on request. Available with premium metallurgies for sour service. No rotation required. Torque transmitted through valve to set lower packer. M.C.A. Valve (60.33) (95.25) (50.42) T107-20A (114.30) (139.70) (101.22) T107-45A (139.70) (165.10) (126.62) T107-55A

5 H Tension Packer The T405 H Tension Packer was designed for use in old scaly casing or open hole applications. The T405 H Packers unique design features make it the packer of choice when producing or injecting in old pipe or open hole applications. The standard packer comes with deep wide wicker slips that allow penetration into scaly casing or open hole formations. The T405 H Packer has three releasing methods built in the design, virtually eliminating retrieval problems. Open J-slot reduces debris build up Safety tubing release Wide wicker slips insure setting in scaly casing Available in single or double element design Automatic J-slot design for easy set and release H Tension Packer Casing Weight lbs/ft (kg/m) (73.00) ( ) (57.15) (19.10) T405-41A (88.90) ( ) (96.00) (38.10) T405-45B (101.60) ( ) (82.55) (38.10) T405-45A (101.60) ( ) (82.55) (47.60) T405-50A (114.30) ( ) (88.90) (50.80) T405-50B (114.30) ( ) (95.25) (50.80) T405-55A (127.00) ( ) (104.78) (50.80) T405-55B (127.00) ( ) (101.60) (50.80) T405-56A (139.70) ( ) (117.40) (50.80) T405-56B (139.70) ( ) (114.30) (50.80) T405-60B (139.70) ( ) (117.40) (61.90) T405-65A (139.70) ( ) (114.30) (61.90) T405-65B (152.40) ( ) (127.00) (61.90) T405-70A (168.30) ( ) (146.10) (61.90) T405-73A (168.30) ( ) (139.70) (61.90) T405-75A (177.80) ( ) (152.40) (61.90) T405-85A (177.80) ( ) (152.40) (76.20) T405-85B (193.70) ( ) (168.30) (61.90) T405-95A (219.10) ( ) (190.50) (61.90) T405-95B (219.10) ( ) (200,00) (61.90) T405-96A (244.50) ( ) (215.90) (63.50) T405-96B (244.50) ( ) (209.60) (63.50) T405-97A (244.50) ( ) (215.90) (76.20) T405-97B (244.50) ( ) (209.60) (76.20) T405-10A (244.50) ( ) (215.90) (101.60) T A (244.50) ( ) (209.60) (101.60) T A (273.10) ( ) (241.30) (63.50) T405-13A (273.10) ( ) (241.30) (76.20) T A (273.10) ( ) (241.30) (101.60) T A (273.10) ( ) (304.80) (101.60) T405-13A

6 SL Tension Packer The T412 SL Tension Packer is a dependable hook wall packer used for water injection and production. The open J-slot and large stainless steel drag springs make the T412 SL ideal for setting in heavily corroded casing. The T412 SL has a right hand rotational safety release built into the top sub. This allows the tubing string to be removed from the packer when normal release procedures fail. Open J-slot reduces debris build up Safety tubing release Wide wicker slips insure setting in scaly casing Available in single or double element design Automatic J-slot design for easy set and release SL Tension Packer Casing Weight lbs/ft (kg/m) (73.00) ( ) (57.15) (19.10) T412-41A (88.90) ( ) (96.00) (38.10) T412-45B (101.60) ( ) (82.55) (38.10) T412-45A (101.60) ( ) (82.55) (47.60) T412-50A (114.30) ( ) (88.90) (50.80) T412-50B (114.30) ( ) (95.25) (50.80) T412-55A (127.00) ( ) (104.78) (50.80) T412-55B (127.00) ( ) (101.60) (50.80) T412-56A (139.70) ( ) (117.40) (50.80) T412-56B (139.70) ( ) (114.30) (50.80) T412-60B (139.70) ( ) (117.40) (61.90) T412-65A (139.70) ( ) (114.30) (61.90) T412-65B (152.40) ( ) (127.00) (61.90) T412-70A (168.30) ( ) (146.10) (61.90) T412-73A (168.30) ( ) (139.70) (61.90) T412-75A (177.80) ( ) (152.40) (61.90) T412-85A (177.80) ( ) (152.40) (76.20) T412-85B (193.70) ( ) (168.30) (61.90) T412-95A (219.10) ( ) (190.50) (61.90) T412-95B (219.10) ( ) (200,00) (61.90) T412-96A (244.50) ( ) (215.90) (63.50) T412-96B (244.50) ( ) (209.60) (63.50) T412-97A (244.50) ( ) (215.90) (76.20) T412-97B (244.50) ( ) (209.60) (76.20) T412-10A (244.50) ( ) (215.90) (101.60) T A (244.50) ( ) (209.60) (101.60) T A (273.10) ( ) (241.30) (63.50) T412-13A (273.10) ( ) (241.30) (76.20) T A (273.10) ( ) (241.30) (101.60) T A (273.10) ( ) (304.80) (101.60) T412-13A-000 3

7 GV-5 Gas Vent Packer The T421 GV-5 Gas Vent Packer System was developed to isolate casing leaks in pumping or injection wells. The GV-5 system can be used on pumping wells with the installation of a tubing anchor catcher used below the packers or with a lower tension packer on injection wells to allow for integrity pressure tests down to the lower packer. The system was designed as an inexpensive alternative to squeeze cementing. The packer style venting system allows for a positive seal against the casing wall where cup style systems fail to perform. Isolate Casing Leaks While Venting Gas From Below Packer Style Makes for Positive Seal Against Casing Wall Tension Set System Allows M.I.T. Integrity Tests to Lower Packer Retrievable and Resetable System GV-5 Gas Vent packer (114.30) (95.25) (50.80) T421-45A (127.00) (101.60) (50.80) T421-50A (139.70) (117.48) (50.80) T421-55A (177.80) (152.40) (63.50) T421-70A-000 4

8 C-1 Tandem Tension Packer The T436 C-1 Tandem Tension Packer is an economical, compact isolation packer. It can be used to isolate casing holes or perforations as well as for multi-zone completions. It is used as the upper packer or packers with a tension packer such as the ASI-X or SL Shear Packer used as the lower packer. The C-1 packer may be run with or without the shear screws. If the packer is run with the shear screws in place, set down weight is required to shear the screws before the packer is moved into the set position. Full bore design. Simple, economical packer for zone isolation. Built in unloader Standard design is left-hand set. Available in right-hand set on request. Shear value field adjustable. T436 C-1 Tandem Tension Packer Casing Weight lb/ft (kg/m) (139.70) ( ) (114.30) (50.42) T436-55A (139.70) ( ) (117.48) (50.42) T436-55B (139.70) ( ) (121.44) (50.42) T436-55C

9 S-1 Tandem Tension Packer The T437 S-1 Tandem Packer is used as an isolation packer in multiple zone completions. Setting: Unjayed position: Apply tension shearing the brass shear screw energizing the packing element. Jayed position: Set down weight shearing the brass shear screws, the rotate 1/8 right hand turn at packer and pull tension to energize the packing element. Releasing: Set down weight to remove applied tension and engage the unloader to Equalize pressures, then rotate 1/8 left hand turn at the packer to re-engage into running jay position. Full bore design Simple, economical packer for zone isolation Built in unloader Available in right or left hand J-slot configurations S-1 Tandem Tension Packer Casing Weight lbs/ft (kg/m) (114.30) ( ) (95.25) (50.80) T437-45A (127.00) ( ) (104.78) (50.80) T437-50A (127.00) ( ) (101.60) (50.80) T437-50B (139.70) ( ) (117.48) (50.80) T437-55A (139.70) ( ) (114.30) (50.80) T437-55B (177.80) ( ) (152.40) (63.50) T437-70B (177.80) ( ) (149.23) (63.50) T437-70A (177.80) ( ) (152.40) (76.20) T437-73B (177.80) ( ) (149.23) (76.20) T437-73A (219.10) ( ) (190.50) (63.50) T437-85A (219.10) ( ) (190.50) (76.20) T437-86A (244.50) ( ) (215.90) (76.20) T437-95B (244.50) ( ) (209.60) (76.20) T437-95A-000 6

10 Casing Packer The T440 Casing Packer is an economical full bore tension or compression packer used for isolating bad areas of casing. The T440 Casing Packer is a versatile tool used for injection, producing & cementing in liner strings. The T440 Casing Packer comes with deep wide wicker slips, single or double element system making this packer ideal for setting in scaly pipe or open hole formations. The T440 Casing Packer is available in either manual or automatic J-slot configurations and is also available with a right hand rotational safety release when run as tension set tool. Full bore design Tension or compression set Available with rotational safety release system Available in single or double element design Economical Easily convertible into liner hanger system Casing Packer Casing Weight lbs/ft (kg/m) (114.30) ( ) (95.25) (63.12) T440-45A (127.00) ( ) (104.80) (63.12) T440-50A (139.70) ( ) (117.40) (75.82) T440-55A (139.70) ( ) (117.40) (88.52) T440-56A (139.70) ( ) (120.65) (88.52) T440-56B (168.28) ( ) (142.88) (101.22) T440-65A (177.80) ( ) (146.00) (101.22) T440-70A (177.80) ( ) (149.23) (113.92) T440-73A (193.70) ( ) (165.10) (101.22) T440-75A (219.10) ( ) (190.50) (101.22) T440-84A (219.10) ( ) (190.50) (126.62) T440-85A (244.48) ( ) (209.55) (164.72) T440-94A (244.48) ( ) (215.90) (164.72) T440-95A (298.45) ( ) (266.70) (202.82) T440-11A (346.08) ( ) (304.80) (228.22) T440-13A

11 WS Hanger Packer The T441 WS Hanger Packer is a compression set liner hanger packer for use in open hole or casing. The T441 WS Hanger uses deep wide wicker slips that penetrate in scaly casing and open hole formations. The WS Hanger cone is shear pinned to eliminate premature setting of the packing element while running, once the slips engage the cone the brass shear screws break energizing the packing element. The T441 WS Hanger Packer is run in using the WS Running Tool. The running tool comes with a two foot stroke allowing rotation at the hanger without picking up on the casing string, this allows the right hand break thread to rotate free and disconnect without damage.. Simple operation Deep wide wicker slips Full opening Stainless steel slip arms drag springs Available in stainless steel construction WS Hanger Packer Casing Weight lbs/ft (kg/m) (114.30) ( ) (95.25) 2.50 (63.50) T441-45A (127.00) ( ) (104.80) 2.50 (63.50) T441-50A (127.00) ( ) (101.60) 2.50 (63.50) T441-50B (139.70) ( ) (117.40) 3.00 (76.20) T441-55A (139.70) ( ) (114.30) 3.00 (76.20) T441-55B (139.70) ( ) (121.40) 3.50 (88.90) T441-56A (139.70) ( ) (118.10) 3.50 (88.90) T441-56B (177.80) ( ) (146.00) 4.00 (101.60) T441-70A (177.80) ( ) (151.60) 4.50 (114.30) T441-71B (177.80) ( ) (157.10) 5.00 (127.00) T441-72B (193.70) ( ) (168.30) 4.00 (101.60) T441-75A (193.70) ( ) (168.30) 5.00 (127.00) T441-76A (219.10) ( ) (190.50) 4.00 (101.60) T441-84A (219.10) ( ) (190.50) 5.00 (127.00) T441-85A (219.10) ( ) (190.50) 5.50 (139.70) T441-86A (219.10) ( ) (194.50) 6.50 (165.10) T441-87B (244.50) ( ) (215.90) 6.00 (152.40) T441-94A (244.50) ( ) (209.60) 6.00 (152.40) T441-94B (244.50) ( ) (215.90) 6.50 (165.10) T441-97A (244.50) ( ) (209.60) 6.50 (165.10) T441-97B (273.10) ( ) (215.90) 6.50 (165.10) T441-10A (273.10) ( ) (215.90) 7.00 (177.80) T A-000 8

12 V.I.P Gas Vent Packer System The T442 V.I.P. Packer is used in conjunction with the TEAM full bore T440 Casing Packer. Together these tools create a unique packer system that are used to isolate bad areas of casing while allowing gas to vent from below. The V.I.P. Packer System can be used in tension or compression, but is ideally suited for pumping wells with the tubing string landed in tension. Full bore design allows maximum tubing size Torque mechanism allows manipulation of packer system Easily adjustable shear mechanism No o-ring seals Packing element design V.I.P. Gas Vent Packer System Casing Weight lbs/ft (kg/m) (114.30) ( ) (95.63) (50.42) T442-45A (139.70) ( ) (117.48) (50.42) T442-55A (139.70) ( ) (117.48) (50.42) T442-56A (177.80) ( ) (146.00) (63.12) T442-70A

13 CS Compression Packer The T444 CS Compression Packer is an inexpensive means of isolating the casing string from the open hole formation or used with the T444 Casing Packer for zone isolation. The T444 is set by applying sufficient weight to shear the setting screws energizing the packing elements. Large bore design Double element design for open hole formations Simple operation, economical M-2 Shear Tension Packer Casing Weight lbs/ft (kg/m) (114.30) ( ) (95.25) 2.50 (63.50) T444-45A (127.00) ( ) (104.80) 2.50 (63.50) T444-50A (127.00) ( ) (101.60) 2.50 (63.50) T444-50B (139.70) ( ) (117.40) 3.00 (76.20) T444-55A (139.70) ( ) (114.30) 3.00 (76.20) T444-55B (139.70) ( ) (121.40) 3.50 (88.90) T444-56A (139.70) ( ) (118.10) 3.50 (88.90) T444-56B (177.80) ( ) (146.00) 4.00 (101.60) T444-70A (177.80) ( ) (151.60) 4.50 (114.30) T444-71B (177.80) ( ) (157.10) 5.00 (127.00) T444-72B (193.70) ( ) (168.30) 4.00 (101.60) T444-75A (193.70) ( ) (168.30) 5.00 (127.00) T444-76A (219.10) ( ) (190.50) 4.00 (101.60) T444-84A (219.10) ( ) (190.50) 5.00 (127.00) T444-85A (219.10) ( ) (190.50) 5.50 (139.70) T444-86A (219.10) ( ) (194.50) 6.50 (165.10) T444-87B (244.50) ( ) (215.90) 6.50 (165.10) T444-97A (244.50) ( ) (209.60) 6.50 (165.10) T444-97B (273.10) ( ) (241.30) 6.50 (165.10) T444-10A (273.10) ( ) (241.30) 7.00 (177.80) T A

14 M-2 Shear Tension Packer The T456 M-2 SHEAR TENSION PACKER is used for water injection testing and, pumping wells. The M-2 design uses an external J-slot unlike most drag block tension packers that use internal J-slots. The external J-slot is extremely durable and will accept torque without damage, it also allows for increased cross- section of the mandrel for optimum wear. The top and bottom connections of the M-2 Packers are interchangeable which allows the packer to convert to compression set tool while maintaining a rotational safety release system. The shear release mechanism use slotted brass screws that remain visible and are easily adjusted in the field. External J-slot design for durability Uses drag blocks for extended life Interchangeable top and bottom connections allows tool to invert (tension or compression) Automatic J-slot for easy release Rotational safety release Shear safety release Uses common replacement parts M-2 Shear Tension Packer Casing Weight lbs/ft (kg/m) (114.30) ( ) (95.25) (49.20) T456-45A (127.00) ( ) (104.80) (49.20) T456-45A (127.00) ( ) (101.60) (49.20) T456-45A (139.70) ( ) (117.40) (49.20) T456-55A (139.70) ( ) (114.30) (49.20) T456-55B (139.70) ( ) (117.40) (60.30) T456-56A (139.70) ( ) (114.30) (60.30) T456-56A (177.80) ( ) (152.40) (63.50) T456-70B (177.80) ( ) (149.20) (63.50) T456-71A (177.80) ( ) (152.40) (76.20) T456-73B (177.80) ( ) (149.20) (76.20) T456-73A (219.10) ( ) (190.50) (63.50) T456-85A (219.10) ( ) (190.50) (76.20) T456-86A (244.50) ( ) (215.90) (63.50) T456-95B (244.50) ( ) (209.60) (63.50) T456-95A (244.50) ( ) (215.90) (76.20) T456-96B (244.50) ( ) (209.60) (76.20) T456-96A US PAT # 7,082,991

15 ASI-X ion Packer The T600 ASI-X ion Packer is a high pressure double grip tubing retrievable packer. It is normally set and retrieved using a ¼ turn to the right but it can be modified to be run on electric wireline if preferred. It is designed to be run with the standard T-2 On-Off Tool disconnect as the seal assembly and retrieving tool. This configuration uses less equipment and trips than a conventional wireline set seal bore packer and allows it to be used in a variety of applications from production packer to retrievable bridge plug. The release mechanism incorporates an internal by-pass which opens to equalize pressure before the upper slips are released from the casing wall by means of a sequential release system. The packer can be set in tension or compression depending on the application. It can be modified to be run on electric wireline using standard setting tools. It can also be supplied in a shear release configuration if needed. Standard setting and releasing methods incorporate a ¼ turn to the right at the tool. The internal by-pass equalizes pressure across the packer to reduce any tendency to swabbing. Use of the T-2 disconnect feature eliminates the need for expensive seal assemblies. Rated to 7,000psi at 300ºF with elevated temperature capabilities up to 425ºF with choice of appropriate elastomers. 12 US PAT # 7,082,991

16 ASI-X ion Packer ASI-X ion Packer Casing Weight lbs/ft (kg/m) (63.50) ( ) (57.15) (22.05) T603-25A (88.90) ( ) (70.64) (31.37) T600-35A (114.30) ( ) (92.86) (48.82) T600-45B (114.30) ( ) (95.25) (48.82) T600-45A (127.00) ( ) (101.60) (48.82) T600-50B (127.00) ( ) (104.78) (48.82) T600-50A (139.70) ( ) (114.30) (50.42) T600-55B (139.70) ( ) (117.48) (50.42) T600-55A (139.70) ( ) (121.44) (50.42) T600-55C (139.70) ( ) ) (59.94) T600-56E (139.70) ( ) (114.30) (59.94) T600-56B (139.70) ( ) (117.48) (59.94) T600-56A (139.70) ( ) (121.44) (59.94) T600-56C (152.40) ( ) (131.78) (59.94) T600-60A (168.28) ( ) (139.70) (63.12) T600-65A (168.28) ( ) (146.05) (63.12) T600-65B (177.80) ( ) (149.23) (63.12) T600-70A (177.80) ( ) (151.61) (63.12) T600-70C (177.80) ( ) (152.40) (63.12) T600-70B (177.80) ( ) (149.23) (75.82) T600-73A (177.80) ( ) (152.40) (75.82) T600-73B (193.68) ( ) (163.91) (63.12) T600-75A (193.68) ( ) (168.28) (63.12) T600-75B (193.68) ( ) (169.47) (63.12) T600-75C (193.68) ( ) (163.91) (75.82) T603-76A (193.68) ( ) (168.28) (75.82) T603-76B (219.08) ( ) (190.50) (63.12) T600-85A (219.08) ( ) (196.85) (63.12) T600-85B (219.08) ( ) (190.50) (75.82) T600-86A (219.08) ( ) (190.50) (101.22) T600-87A (244.48) ( ) (209.55) (101.22) T600-95A (244.48) ( ) (215.90) (101.22) T600-95B US PAT # 7,082,991

17 ASI-X 10K ion Packer The T600 ASI-X 10K ion Packer is a high pressure double grip tubing retrievable packer. It is normally set and retrieved using a ¼ turn to the right but it can be modified to be run on electric wireline if preferred. It is designed to be run with the standard T-2 On-Off Tool disconnect as the seal assembly and retrieving tool. This configuration uses less equipment and trips than a conventional wireline set seal bore packer and allows it to be used in a variety of applications from production packer to retrievable bridge plug. The release mechanism incorporates an internal by-pass which opens to equalize pressure before the upper slips are released from the casing wall by means of a sequential release system. The packer can be set in tension or compression depending on the application. It can be modified to be run on electric wireline using standard setting tools. It can also be supplied in a shear release configuration if needed. Standard setting and releasing methods incorporate a ¼ turn to the right at the tool. The internal by-pass equalizes pressure across the packer to reduce any tendency to swabbing. Use of the T-2 disconnect feature eliminates the need for expensive seal assemblies. Rated to 10,000psi at 250ºF with elevated temperature capabilities up to 425ºF with choice of appropriate elastomers. ASI-X 10K ion Packer Casing Weight lbs/ft (kg/m) (114.30) ( ) (93.47) (48.82) T600-45B (114.30) ( ) (93.47) (48.82) T600-45B (114.30) ( ) (95.66) (48.82) T600-45A (127.00) ( ) (101.60) (50.39) T600-50B (127.00) ( ) (101.60) (50.39) T600-50B (127.00) ( ) (104.78) (50.39) T600-50A (139.70) ( ) (114.30) (50.42) T600-55B (139.70) ( ) (117.48) (50.42) T600-55A (139.70) ( ) (121.44) (50.42) T600-55C (139.70) ( ) ) (59.94) T600-56E (139.70) ( ) (114.30) (59.94) T600-56B (139.70) ( ) (114.30) (59.94) T600-56B (139.70) ( ) (117.48) (59.94) T600-56A (168.28) ( ) (139.70) (63.09) T600-65A (168.28) ( ) (146.05) (63.09) T600-65B (177.80) ( ) (149.23) (63.12) T600-70A (177.80) ( ) (151.61) (63.12) T600-70C (177.80) ( ) (152.40) (63.12) T600-70B-010 US PAT # 7,082,991 14

18 ASI-X HP ion Packer The T603 ASI-X HP ion Packer is a high pressure double grip tubing retrievable packer that holds pressure from above and below. The HP version of this ASI-X packer is capable of being set in tnesion or compression, once set the tubing string can be left in tension, compression or neutral. It is normally set and retrieved using a ¼ turn to the right. It is designed to be run with the standard T-2 On-Off Tool disconnect as the seal assembly and retrieving tool. The release mechanism incorporates an internal by-pass which opens to equalize pressure before the upper slips are released from the casing wall by means of a sequential release system. The packer can be set in tension, compression or neutral depending on the application. Standard setting and releasing methods incorporate a ¼ turn to the right at the tool. The internal by-pass equalizes pressure across the packer to reduce any tendency to swabbing. Use of the T-2 disconnect feature eliminates the need for expensive seal assemblies. Available in shear relase design. Standard element design rated at 250 F with elevated temperature capabilities up to 425 F with choice of appropriate elastomers. Standard flow wet parts AISI , 110 KSI. ASI-X HP ion Packer Casing Weight lbs/ft (kg/m) (193.68) ( ) (158.75) (63.12) T603-70G (193.68) ( ) (163.91) (63.12) T603-75A (193.68) ( ) (169.47) (63.12) T603-75C (219.08) ( ) (190.50) (75.82) T603-85A (244.48) ( ) (209.55) (101.22) T603-95A (244.48) ( ) (209.55) (101.22) T603-95B US PAT # 7,082,991

19 Patriot Packer The T607 Patriot Packer is a mechanically set retrievable production packer used in many applications, particularly in injection wells. It is a double grip packer utilizing a special upper slip releasing system which reduces the forces required to release. Once set it is mechanically locked and can hold substantial pressures from above or below. Set with a ¼ turn to the right the Patriot can be set shallow with tension or deeper with compression and once set it can remain in neutral making it ideal for applications where pressure reversals are anticipated. It can also be set on wireline if required, with an On/Off Tool, for greater versatility. Holds pressure differentials from above and below. Set and released by a ¼ turn to the right followed by compression or tension as required. Can be run with an On/Off Tool with suitable tubing release mechanism. Can be set at any depth in tension, compression or neutral. An internal by-pass allows for faster running in. The same by-pass opens first to equalize pressure upon retrieval and counters any swabbing tendency while pulling out. Upper slip releasing system reduces retrieval force requirements. Can be run on electric line using a wireline adapter kit and On/Off Tool seal nipple for greater versatility. Available in materials suitable for corrosive environments upon request. Patriot Packer (114.30) (95.25) (48.85) T607-45A (139.70) (117.48) (50.42) T607-55A (139.70) (121.44) (50.42) T607-55C (139.70) (114.30) (59.94) T607-56B (139.70) (117.48) (59.94) T607-56A (139.70) (121.44) (59.94) T607-56C (177.80) (149.23) (63.12) T607-70A (177.80) (151.61) (63.12) T607-70C (177.80) (152.40) (63.12) T607-70B (177.80) (152.40) (75.82) T607-73B (177.80) (158.75) (75.82) T607-73A (244.48) (209.55) (101.22) T607-95A (244.48) (215.90) (101.22) T607-95B (273.05) (239.70) (101.22) T607-10B (273.05) (246.08) (101.22) T607-10A (298.45) (266.70) (101.22) T607-11A-020 US PAT # 7,591,305 US PAT # 7,082,991 16

20 ASII Compression Packer The T611 ASII Double Grip Retrievable Packer is used for production, stimulation and testing. The mechanical upper hold down system reduces the cost and maintenance of a button type hydraulic hold down system. The ASII Packer is equipped with a running bypass that reduces swabbing. Set down weight closes the bypass valve, sets the upper and lower slips and energizes the packing elements. The closed bypass valve activates the pressure balanced hold down system. Pressure from below aids in holding the bypass valve closed and preventing upward movement of the tubing string. No hydraulic hold down buttons Built in unloader washes debris from when retrieving Sequential release upper slip system Available in automatic and manual configurations ASII ion Packer Casing Weight lbs/ft (kg/m) (73.00) ( ) (57.15) (15.49) T611-25A (73.00) ( ) (57.15) (15.49) T611-25A (88.90) ( ) (70.63) (31.37) T611-35A (88.90) ( ) (70.63) (31.37) T611-35A (114.30) ( ) (92.99) (48.84) T611-45B (114.30) ( ) (95.25) (48.84) T611-45A (127.00) ( ) (101.60) (48.84) T611-50B (127.00) ( ) (104.78) (48.84) T611-50A (139.70) ( ) (117.48) (50.42) T611-55A (139.70) ( ) (111.91) (59.94) T611-56E (139.70) ( ) (114.30) (59.94) T611-56B (139.70) ( ) (117.48) (59.94) T611-56A (139.70) ( ) (121.44) (59.94) T611-56C (177.80) ( ) (149.23) (63.12) T611-70A (177.80) ( ) (151.61) (63.12) T611-70C (177.80) ( ) (152.40) (63.12) T611-70B (177.80) ( ) (149.23) (75.82) T611-73A (177.80) ( ) (151.61) (75.82) T611-73C (177.80) ( ) (152.40) (75.82) T611-73B US PAT # 7,082,991 17

21 AS-5 Anchor Packer The T628 AS-5 Anchor Packer is the upper packer in a zone isolation completion. The packer was designed to run above the AS-6 Compression Packer. The AS-5 Packer sets by applying weight closing the bypass seal and energizing the packing elements. Once set the AS-5 can be locked in place allowing the tubing string to be removed using the T-2 On/Off Tool. The AS-5 sets and releases with one quarter turn right hand rotation at the packer. Allows tubing disconnect in straddle completions Sequential release slip system Large bypass area Equalizing bypass system opens before upper slips are released Premium thread connection available upon request. Packing element combo available up to 450 F, see TEAM Oil Tools Elastomer Guide. AS-5 Anchor Packer (114.30) (95.25) (48.90) T628-45A (127.00) (104.78) (48.90) T628-50A (139.70) (114.30) (50.42) T628-55B (139.70) (117.48) (50.42) T628-55A (139.70) (114.30) (59.94) T628-56B (139.70) (117.48) (59.94) T628-56A (139.70) (121.84) (59.94) T628-56C (177.80) (152.40) (63.12) T628-70B (244.48) (209.55) (101.22) T628-95A (244.48) (215.90) (101.22) T628-95B

22 AS-6 Anchor Packer The T629 AS-6 Anchor Packer is a single grip compression packer designed for use as the bottom packer in a zonal isolation completion. It is typically used in conjunction with a T-628 AS-5 anchor packer to provide a two packer system which can be set by compression. This combination in conjunction with a T-2 On/Off Tool allows for zonal isolation while providing the facility to retrieve the tubing if required without disturbing the packers. It is set by applying a quarter turn at the packer and setting down weight and is released by straight pick up. It has an extended seal area which allows tubing movement and/or pressure changes between the packers. It can also be used as a single grip production packer in applications where low differential pressures from below are anticipated. Extended stroke seal area maintains a seal in all conditions. Large by-pass area facilitates fast run in and alleviates swabbing when retrieving. Available in right or left hand automatic or manual J-slot configurations. Sets with compression and retrieves with straight pull. Can be used as a single string production packer in suitable conditions. Premium thread connection available upon request. Packing element combo available up to 450 F, see TEAM Oil Tools Elastomer Guide. AS-6 Anchor Packer (114.30) (95.25) (48.90) T629-45A (114.30) (95.25) (48.90) T629-45A (127.00) (104.78) (48.90) T629-50A (139.70) (117.48) (50.42) T629-55A (139.70) (117.48) (50.42) T629-55A (139.70) (114.30) (59.94) T629-56B (139.70) (117.48) (59.94) T629-56A (139.70) (121.44) (59.94) T629-56C (177.80) (152.40) (63.12) T629-70B-000 US PAT # 7,082,991 19

23 AS-3 Single Grip Packer The T631 AS-3 Single Grip Packer is designed for use in wells that where minimal differential from below is anticipated so that a hold down device is not needed. It is set by applying a quarter turn to the right at the packer followed by set down weight. The packer is released by straight pick up to open the large by-pass allowing equalization. After equalization, the packing elements release reducing tendency of swabbing when pulling out of wellbore. Full opening design allows unrestricted fluid flow and wireline tool movement through the tubing. Set by right-hand rotation and set down weight. Large by-pass for ease of running and swabbing prevention when retrieving. Available with optional setting bottom configurations. Straight pick-up to release. Full through bore allows for unrestricted fluid flow and wireline tool access. Premium thread connection available upon request. Packing element combo available up to 450 F, see TEAM Oil Tools Elastomer Guide. AS-3 Single Grip Packer (114.30) (95.25) (49.10) T631-45A (139.70) (114.30) (50.42) T631-55B (139.70) (117.48) (50.42) T631-55A (139.70) (114.30) (59.94) T631-56B (139.70) (117.48) (59.94) T631-56A (139.70) (121.44) (59.94) T631-56C (168.28) (139.70) (63.12) T631-65A (177.80) (149.23) (63.12) T631-70A (177.80) (149.23) (63.12) T631-70C (177.80) (152.40) (63.12) T631-70B (193.68) (163.91) (63.12) T631-75A (193.68) (168.28) (63.12) T631-75B (219.08) (190.50) (63.12) T631-85A (244.48) (209.55) (101.22) T631-95A (244.48) (215.90) (101.22) T631-95B-000 US PAT # 7,082,991 20

24 SnapSet II Compression Isolation Packer The T636 SnapSet II is a compression set single string isolation packer. The SnapSet II is used where high-differential pressures above the packer are not expected. It is typically run in a zonal isolation completion, in tandem with a lower anchor packer, such as the T600 ASI-X allowing compression setting. It is equipped with a collet which shifts at a predetermined compression value to prevent premature setting during run in. Once the collet shifts the packing elements are engaged and the hold down slips are activated and set. It is released by straight pick up on the tubing, opening the by-pass and releasing the upper slips. The hold down system incorporates a compensating piston. The large by-pass area facilitates run in and counteracts any tendency to swabbing when retrieving. The equalizing system allows the packing element to relax before retrieval. The body is keyed to allow rotation through the packer if needed. Three element packing system. Internal collet to prevent premature setting. Sequential slip release system. Can be run with the T-2 On-Off Tool to allow tubing retrieval. Premium thread connection available upon request. Packing element combo available up to 450 F, see TEAM Oil Tools Elastomer Guide. SnapSet II Compression Isolation Packer (114.30) (92.86) (48.84) T636-45B (114.30) (95.25) (48.84) T636-45A (139.70) (117.48) (50.42) T636-55A (139.70) (117.48) (59.94) T636-56A (139.70) (121.44) (59.94) T636-56C (177.80) (149.23) (63.12) T636-70A (177.80) (151.61) (63.12) T636-70C (177.80) (152.40) (63.12) T636-70B (193.68) (169.47) (63.12) T636-75C (219.08) (196.85) (63.12) T636-85B US PAT # 7,082,991 21

25 Compression Isolation Packer The T641 Compression Isolation Packer is an economical means of isolating multiple zone wells. The T641 Packer is used as the upper packer in tandem string applications Economical Adjustable shear values Resetable Simple operation Compression Isolation Packer Tubing size (114.30) (60.30) (95.25) (50.80) T641-45A (127.00) (60.30) (101.60) (50.80) T641-50A (139.70) (60.30) (117.40) (50.80) T641-55A (139.70) (73.00) (117.40) (50.80) T641-56A (177.80) (73.00) (152.40) (63.50) T641-70B (177.80) (73.00) (149.23) (63.50) T641-70A (177.80) (88.90) (149.23) (76.20) T641-73A (177.80) (88.90) (152.40) (76.20) T641-73B (244.78) (101.60) (215.90) (101.60) T641-97A

26 HS-1 Hydraulic ion Packer The T650 HS-1 Hydraulic Set Packer is a high pressure hydraulic set double grip production packer for use in wells where it is desirable to set after the well has been flanged up. It is equally suitable for single completions or in wells where multiple packers are required, because the pressure balance system is zone activated thus offsetting pressure differentials across the packer. All parts are locked to prevent presetting due to pressure build up or debris when running in. It is retrieved by a straight pull shear release. Suitable for single or multiple packer completions. All components are locked to prevent premature setting during run in. Set by hydraulic pressure from surface against a plug or ball and set below. Once set the release shear mechanism is unaffected by differential pressures. A pressure balanced system offsets pressure reversals. Released by a straight pull. HS-1 Hydraulic ion Packer Temp. Rating F ( C) Pressure rating PSI (bar) (114.30) (92.86) (50.39) 300 (148.89) 7,000 (382.63) T650-45B (114.30) (95.25) (50.39) 300 (148.89) 7,000 (382.63) T650-45A (139.70) (114.30) (50.39) 300 (148.89) 7,000 (382.63) T650-55B (139.70) (117.48) (50.39) 300 (148.89) 7,000 (382.63) T650-55A (146.05) (120.50) (50.39) 300 (148.89) 7,000 (382.63) T650-55D (168.28) (139.70) (63.09) 300 (148.89) 7,000 (382.63) T650-65A (177.80) (149.23) (63.09) 300 (148.89) 7,000 (382.63) T651-70A (177.80) (152.40) (63.09) 300 (148.89) 7,000 (382.63) T651-70B (177.80) (149.23) (75.79) 300 (148.89) 7,000 (382.63) T650-73A (177.80) (152.40) (75.79) 300 (148.89) 7,000 (382.63) T650-73B (193.68) (163.91) (75.79) 300 (148.89) 7,000 (382.63) T650-75A (193.68) (168.28) (75.79) 300 (148.89) 7,000 (382.63) T650-75B (244.48) (209.55) (75.79) 300 (148.89) 5,000 (344.74) T650-95A (244.48) (215.90) (75.79) 300 (148.89) 5,000 (344.74) T650-95B (244.48) (209.55) (100.03) 300 (148.89) 5,000 (344.74) T650-96A US PAT # 7,082,991

27 HS-4 Isolation Packer The TEAM T654 HS-4 Isolation Packer is a hydraulic set, single string tandem packer used in multiple zone well completions. It can be used as the upper packer in a dual zone applications or I multiple quantities when more than two zones are to be completed. The HS-4 is set by applying hydraulic pressure to the tubing against a temporary plug located below to shear the setting screws and pack off the elements. It is released by straight pull which shears the releasing screws allowing the packing elements to relax and equalizing pressure from tubing to annulus. Economical Deisgn Easily adjustable set and release shear screws, both field adjustable. Compact length makes it ideal for use in highly deviated wells. Standard three piece nitrile packing elements, premium elements available on request. Flow wet material is AISI , 80 KSI, premium material available on request. End connections EUE 8 Rd, premium threads available on request. HS-4 Isolation Packer Casing Weight lb/ft (kg/m) (114.30) ( ) (95.25) (50.42) T654-45A (127.00) ( ) (104.78) (50.42) T654-50A (139.70) ( ) (117.48) (50.42) T654-55A (139.70) ( ) (117.48) (63.12) T654-56A (177.80) ( ) (149.23) (63.12) T654-70A (177.80) ( ) (152.40) (63.12) T654-70B

28 HSR-4 Hydraulic ion Packer The T658 HSR-4 is a hydraulic set retrievable production packer suitable for use in high pressure well completions. It is very compact and highly suitable for use in deviated wells. It features a bi-directional slip which holds pressure from above and below. The lock ring holds the packing elements in the full set position and is unaffected by pressure reversals. The packer does not have an internal by-pass to allow equalization when releasing. It is recommended to utilize an On/Off Tool or sliding sleeve above the packer to aid equalization. Hydraulic set by pressure against a down hole plugging device below. The well can be flanged up before setting the packer. Three element packing system for high pressure applications. Retrieved by means of a field adjustable shear release. Bi-directional slip system which is locked in place to prevent preset while running in. All o-rings are located below the packing element. An equalization device is recommended to counter swabbing when retrieving. Alternative packing elements, premium threads and metallurgy available on request. Full tubing ID. Torque through capability. HSR-4 Hydraulic ion Packer (114.30) (95.25) (50.42) T658-45A

29 MSV Dual Compression Packer The T900 MSV Dual Compression Packer is a retrievable compression set isolation packer which is used as the upper packer in a tow packer chamber gas lift completion. The bypass tube is an integral part of the MSV and a telescoping slip joint is used for spacing out and connection to a gas lift mandrel. The packer is keyed with heavy duty bolts that allow torque to be applied for setting and releasing of a lower packer. Once the lower packer is set, set down weight is applied to shear the screws in the MSV packer and energize the packing element. Simple operation. Rugged construction. Compression set - straight pick-up release. Field adjustable setting shear screws. T900 MSV Dual Compression Packer Casing Weight lb/ft (kg/m) (139.70) ( ) (114.30) (48.82) T900-55B (177.80) ( ) (152.40) (63.12) T900-70B

30 T901 R-2 Dual String Tension Packer The T901 R-2 Dual String Tension Packer is the upper packer in multi-zone installations. The T901 R-2 Tension Packer is used with the M-2 Tension Packer for simple multi-zone waterflood wells. The R-2 Dual String Packer can handle large volumes of fluid eliminating the use of downhole flow regulators. Setting: Run the M-2 and R-2 packers to setting depth, with the last movement downward turn one quarter turn to the left and pick-up, this will set the lower M-2 Tension Packer. Run the J-latch seal assembly into the R-3 Packer and pull tension to achieve pack-off. Release: Slack off on short string will relax the R-3 packing element and turn one quarter turn to right at packer and pick up to release short string from packer. Slack off on long string and turn one quarter turn to the right to relax M-2 packer element and release slip assembly. The M-2 Tension Packer may also be shear released at a pre-determined value. Full Bore Design Economical Simple Operation Can Be Used Shallow or Deep Available with Nickel or Plastic Coatings T901 R-2 Dual String Tension Packer Casing Weight lb/ft (kg/m) (139.70) ( ) (117.48) (50.80) T901-55A (139.70) ( ) (114.30) (50.80) T901-55B (177.80) ( ) ( (63.50) T901-70B (177.80) ( ) (149.23) (63.50) T901-70A (219.07) ( ) (190.50) (63.50) T901-85A

31 HS-II Hydraulic Set Dual String Packer The T905 HS-II is a high pressure hydraulic set dual string production packer usually run above a single string hydraulic or wireline set single string packer in a dual completion. It can also be readily modified for use as a low pressure packer in a submersible pump completion. Its compact length makes it ideal for use in deviated wells or in applications where doglegs are anticipated. The sequential upper slip release system ensures that each slip is released individually to reduce the loads required to release the packer. The HS-II Packer is available with short string or long string setting capabilities and a variety of tubing connections and short string seal options. It is also adaptable for electric, submersible pump applications. Hydraulic set to allow well completions to be flanged up before setting. Released by straight pull on the long string with field adjustable shear setting. Dressed with upper slip rather than hold-down buttons for added reliability. Can be pressure tested on location prior to running. All components locked in place to avoid premature setting while running in. Available in long or short sting set configuration. Shear release mechanism is unaffected by differential pressures. Short string connection can be threaded or configured with a seal bore to accept locator, J-latch or snap latch seals. Premium thread connections are available upon request. HS-II Hydraulic Set Dual String Packer Long String Short String Tensile Tensile lbs/ft (kg/ft) lbs/ft (kg/ft) (177.80) (150.83) (49.10) ( ) (49.10) ( ) T905-70A (177.80) (150.83) (49.10) ( ) (49.10) ( ) T905-70A (244.48) (211.15) (73.91) ( ) (73.91) ( ) T905-96A

32 TEAM Pack The Team Oil Tools T265 Team Pack packer is a retrievable seal bore packer which can be run on electric line with a wireline adapter kit and setting tool or on tubing using a hydraulic setting tool. All the load bearing parts are designed to withstand high tensile loads and the bidirectional slips prevent any movement after setting. It is retrieved by a straight pull release mechanism using a Team Pack Retrieving Tool. Designed for use in vertical, deviated or horizontal well completion applications. Bi-directional slips prevent any movement after setting. An internal locking device maintains pack off. Retrieved by a straight pull shear release using a Team Pack retrieving tool. Retrieving tool has an emergency shear release feature in the event that the packer does not release. Available with materials and elastomers suitable for standard or sour service. Rated at 10,000psi and up to 425 F with Special Ecner Array elastomers. TEAM Pack (114.30) (99.21) (63.50) T265-45A (139.70) (117.47) (76.20) T265-56B (139.70) (117.47) (76.20) T265-56A (177.80) (150.83) (101.60) T265-73A (177.80) (152.40) (101.60) T265-73B (177.80) (152.40) (101.60) T265-73C (193.68) (163.53) (101.60) T265-76A (193.68) (169.88) (101.60) T265-76B

33 TL Perma-Pack Seal Bore Packer The T670 Perma-pack Permanent Seal Bore ion Packer is a versatile tool that can be used for single or multiple zone completions. The Perma-pack is ideally suited for wells where high pressure, temperatures and corrosive fluids are anticipated. The packer is available in a variety of elastomers and seal bore materials to meet the most hostile down hole environments. The Perma-pack is recommended for injection stimulation, testing or can be converted into a temporary bridge plug by using a knock-out, pump-out or screw-out plug bottom assembly. The Perma-Pack Packer is available with a complete line of tubing seal accessories and elastomers. Seal assemblies are available with TATR, TRTR, TVTR, BONDED NITRILE, BONDED VITON, BONDED ECO and BONDED EPDM. Electric line set, hydraulic set or mechanical set Components keyed for milling Anti-extrusion rings expand to casing I.D. to prevent rubber extrusion Designed to accommodate competitive seal bore accessories. Full circle slip allow for fast run time TL Perma-Pack Seal Bore Packer Casing Weight lb/ft (kg/m) Packer Bore Min. Bore Thru Seals (114.30) ( ) (95.20) (60.71) (43.26) T670-43A (114.30) ( ) (91.29) (63.50) (48.29) T670-44B (114.30) ( ) (95.20) (68.28) (49.29) T670-45A (127.00) ( ) (100.79) (60.71) (43.26) T670-50A (127.00) ( ) (100.79) (68.28) (49.23) T670-51A (127.00) ( ) (107.95) (68.28) (49.23) T670-55C (139.70) ( ) (115.87) (68.28) (49.23) T670-55A (139.70) ( ) (112.70) (68.28) (49.23) T670-55B (139.70) ( ) (115.87) (76.20) (60.30) T670-56A (139.70) ( ) (112.70) (76.20) (60.30) T670-56B (177.80) ( ) (144.45) (82.55) (61.11) T670-70A (177.80) ( ) (138.89) (82.55) (61.11) T670-70C (177.80) ( ) (157.15) (82.55) (61.11) T670-70B (177.80) ( ) (152.40) (101.60) (76.20) T670-71A (177.80) ( ) ( ) (101.60) (76.20) T670-71B (193.70) ( ) (158.75) (82.55) (61.11) T670-75A (193.70) ( ) (165.10) (101.60) (76.20) T670-76A (193.70) ( ) (158.75) (101.60) (76.20) T670-76B (244.50) ( ) (206.38) (82.55) (61.11) T670-95A (244.50) ( ) (206.38) (101.60) (76.20) T670-96A (244.50) ( ) (206.38) (120.65) (98.43) T670-97A (244.50) ( ) (214.33) (152.40) (123.83) T670-98B (244.50) ( ) (208.74) (152.40) (123.83) T670-98A

34 JL Perma-Pack Seal Bore Packer The T671 Perma-Pack Permanent Seal bore ion Packer is a versatile tool that can be used for single or multiple zone completions. The Perma-Pack is ideally suited for wells where high pressure, temperature and corrosive fluids are anticipated. The packer is available in a variety of elastomer and seal bore materials to meet the most hostile downhole environments. The PERMA- PACK is recommended for injection, stimulation, testing or plugging by latching a equalizing packer plug into the top connection. The Perma-Pack is available with a complete line of tubing seal accessories and elastomers. Electric line set, hydraulic set or mechanical set Components keyed for milling Anti-extrusion rings expand to casing I.D. to prevent rubber extrusion Designed to accommodate competitive seal bore accessories. Full circle slip allow for fast run time JL Perma-Pack Seal Bore Packer Casing Weight lb/ft (kg/m) Packer Bore Min. Bore Thru Seals (114.30) ( ) (95.20) (60.71) (43.26) T671-43A (114.30) ( ) (91.29) (63.50) (48.29) T671-44B (114.30) ( ) (95.20) (68.28) (49.29) T671-45A (127.00) ( ) (100.79) (60.71) (43.26) T671-50A (127.00) ( ) (100.79) (68.28) (49.23) T671-51A (127.00) ( ) (107.95) (68.28) (49.23) T671-55C (139.70) ( ) (115.87) (68.28) (49.23) T671-55A (139.70) ( ) (112.70) (68.28) (49.23) T671-55B (139.70) ( ) (115.87) (76.20) (60.30) T671-56A (139.70) ( ) (112.70) (76.20) (60.30) T671-56B (177.80) ( ) (144.45) (82.55) (61.11) T671-70A (177.80) ( ) (138.89) (82.55) (61.11) T671-70C (177.80) ( ) (157.15) (82.55) (61.11) T671-70B (177.80) ( ) (152.40) (101.60) (76.20) T671-71A (177.80) ( ) ( ) (101.60) (76.20) T671-71B (193.70) ( ) (158.75) (82.55) (61.11) T671-75A (193.70) ( ) (165.10) (101.60) (76.20) T671-76A (193.70) ( ) (158.75) (101.60) (76.20) T671-76B (244.50) ( ) (206.38) (82.55) (61.11) T671-95A (244.50) ( ) (206.38) (101.60) (76.20) T671-96A (244.50) ( ) (206.38) (120.65) (98.43) T671-97A (244.50) ( ) (214.33) (152.40) (123.83) T671-98B (244.50) ( ) (208.74) (152.40) (123.83) T671-98A

35 Hydro Perma-Pak The T674 Hydro Perma-Pak is a hydraulic-set dual bore permanent packer set by applied applied hydraulic pressure against a temporary plugging device set below the packer. The Hydro Perma-Pak has a large upper seal bore allowing the use of an anchor latch to create the largest possible I.D. through the packer and seals for completions requiring large tubing sizes. It can be converted to a temporary bridge plug with the addition of a knockout, pump out or threaded plug for temporary lower zone isolation-this plug can be used to apply the setting pressure. Hydraulic-set, by tubing pressure applied to a temporary plug set below the packer. No rotation is required to set. The anti-extrusion back-up rings expand to full casing I.D. to provide positive retention of the packing element. A larger diameter upper seal bore accepts an anchor seal assembly to maximize thru bore. Packing element options are available for high temperatures and H2S/CO2 applications. Seal materials such as Kalrez, Aflas, Viton, Teflon, Ryton, HNBR and Nitrile are available. Hydro Perma-Pak Casing Weight lb/ft (kg/m) MIN I.D (139.70) ( ) (112.70) (69.95) T674-57B (139.70) ( ) (112.70) (69.95) T674-57B (139.70) ( ) (115.90) (69.95) T674-57A (139.70) ( ) (115.90) (69.95) T674-57A

36 DB Perma-Pak The T-648 DB Perma-Pak packer is a versatile permanent seal bore packer which may be set on electric line or hydraulically depending on requirements. The DB Perma-Pak has a large upper seal bore allowing the largest possible I.D. through the packer and seals for completions requiring large tubing sizes. It is particularly suitable for use in stimulation jobs where excessive pressure and/or temperature conditions are anticipated. It can be converted to a temporary bridge plug with the addition of a knockout, pump out or threaded plug for temporary lower zone isolation. Threads, seal bores and packer tops are standardized to maximize their interchangeability with competitive seal bore equipment. Can be set on electric line or hydraulic setting tool. The anti-extrusion back-up rings expand to full casing I.D. to provide positive retention of the packing element. A larger diameter upper seal bore accepts an anchor seal assembly to maximize thru bore. Packing element options are available for high temperatures and H2S/CO2 applications. Seal materials such as Kalrez, Aflas, Viton, Teflon, Ryton, HNBR and Nitrile are available. DB Perma-Pak Casing Weight lb/ft (kg/m) MIN I.D (88.90) ( ) (70.36) (34.80) T648-35A (101.60) ( ) (82.55) (44.45) T648-40A (127.00) ( ) (100.79) (63.15) T648-50A (177.80) ( ) (144.45) (101.60) T648-71C (177.80) ( ) (149.23) (101.60) T648-71B (177.80) ( ) (152.40) (101.60) T648-71A

37 Scorpion Packer The Team T1125 Scorpion Packer is a permanent wireline set production packer with threaded top and bottom connections of choice. It is designed to be run in conjunction with a T512 T-2 On/Off overshot and T510 T-2 On/Off stinger to simplify and speed up well completion. The packer and stinger are made up together and run and set on electric wireline using a standard wireline adapter kit, the tubing and overshot are then run, spaced out and landed using standard techniques. Setting on electric wireline, using the combination of a power charge and a pressure setting assembly, enables the packer to be accurately located in the well by correlation with well logs. Allows placement of the packer in a much shorter time than tubular conveyed methods. Simple and fast installation process. Releasing the tubing from the packer requires only a ¼ turn at the packer. The seals are retained in the overshot rather than exposed as in standard seal assemblies. Available in sizes 4-1/2 thru 7 and a standard pressure rating of 10,000psi. Available for standard service with Nitrile packing elements. Available for sour service with an Aflas Ecner array packing element. Stinger can be supplied with a variety of profiles for landing plugs etc. Full circle slips allow for fast run in time. Scorpion Packer Casing Weight lb/ft (kg/m) (114.30) ( ) (91.44) (50.80) T B (127.00) ( ) (98.43) (50.80) T C (127.00) ( ) (98.43) (49.02) T C (127.00) ( ) (100.81) (49.23) T A (139.70) ( ) (112.70) (50.80) T B (139.70) ( ) (112.70) (50.80) T B (177.80) ( ) (144.45) (63.09) T B

38 H/D Tubing Anchor Catcher The T312 H/D Tubing Anchor Catcher is a heavy duty rationally activated tool used to prevent vertical movement of the tubing string. The H/D Anchor uses drag blocks in place of friction springs allowing for better torque resistance and longevity. The H/D Anchor sets to the left, releases to the right or can be shear released with an easily adjustable shear release system. The H/D Anchor can also be special ordered for right hand set, left hand release with Team Torque slips allowing the tool to be with progressive cavity pumps.. Drag block design for durability and torque Easily adjustable shear release mechanism Full bore design Available in right hand set for PCP applications HD Tubing Anchor Catcher Casing Weight lb/ft (kg/m) (114.30) ( ) (95.25) (50.80) T312-45A (127.00) ( ) (101.60) (50.80) T312-50A (127.00) ( ) (104.77) (50.80) T312-50B (139.70) ( ) (117.47) (50.80) T312-55A (139.70) ( ) (114.30) (50.80) T312-55B (139.70) ( ) (117.47) (63.50) T312-56A (139.70) ( ) (114.30) (63.50) T312-56B (177.80) ( ) (146.10) (63.50) T312-70A

39 RT Anchor / Catcher The T354 RT Anchor Catcher was developed to run with a progressive cavity pump on fiberglass tubing string. The unique slip design allows the anchor to grip the casing wall when right hand rotation is applied and prevents any right handed torque. The RT Anchor Catcher sets to the right, releases to the let or straight pull of the tubing string will engage the adjustable shear safety release mechanism. Vertically cut wicker slip allows right hand torque Reduces wear on tubing string Right hand set, left hand release or shear release Parts interchangeable with standard tool Sturdy stainless steel drag springs RT Anchor Catcher Casing Weight lb/ft (kg/m) Tubing Min O.D (114.30) ( ) (95.25) (50.80) T354-45A (139.70) ( ) (114.30) (50.80) T354-55A (139.70) ( ) (114.30) (60.30) T354-56A (177.80) ( ) (149.20) (63.50) T354-70A (177.80) ( ) (149.20) (50.80) T354-71A

40 T-2 On/Off Tool Stinger The T510 T-2 ON/OFF TOOL STINGERS are used to disconnect the tubing string from a packer. The stingers are used with the T512 T-2 Overshot and are available in a variety of profile types, sizes and from a broad range of material types. 37

41 T-2 On/Off Connector The T-2 On/Off Connector was designed to disconnect and connect the tubing string from/ to a double grip production packer, such as the AS1-X, that does not require tension or compression to maintain a pack-off. It consists of two components, the T510 Stinger and the T512 Overshot and it can be used in treating, fracing, testing and production applications. The Stinger can be supplied with an internal profile of choice to accept a wireline plug and the complete tool is available in a broad range of materials to suit standard or sour service applications to 10,000psi with seal materials suitable for up to 425ºF. Fully field tested and proven bonded seal system Designed for strength and durability Stinger profile nipple can be supplied as specified by client. Available in metallurgy to suit standard, sour and high temperature applications. Can be supplied shear pinned in the up or down position As an alternative a spring loaded design is available. T-2 On/Off Connector Temp. Rating F ( C) Pressure Rating Psi (bar) (139.70) (114.30) (50.39) 300 (148.89) 10,000 (689.48) T512-55A (139.70) (114.30) (63.09) 300 (148.89) 10,000 (689.48) T512-56A

42 T-2 Type H On/Off Tool The T513 T-2 Type H On/Off Tool is used in liner applications to disconnect the liner from the tubing string. The overshot is the liner top or guide, while the stinger is used for the running tool. The seals have been relocated to the stinger allowing the seal to be replaced. T-2 Type H On/Off Tool Thread Connection Inches (114.30) (95.25) (60.30) 2-3/8 EUE 8RD T513-46A

43 RH Rotational Safety Joint The T568 Rotational Safety Joint provides for emergency release of the tubing string. The RH Rotational Safety Joint uses larger square left- hand threads to separate the upper and lower subs with right-hand rotation abandoning any production equipment below. RH Rotational Safety Joint Thread Connection Inches (42.20) (56.40) (34.90) EUE 10RD T568-16A (48.30) (63.50) (38.10) EUE 10RD T568-19A (60.30) (77.80) (50.80) EUE 8RD T568-20A (73.00) (93.70) (63.50) EUE 8RD T568-25A (88.90) (114.30) (76.20) EUE 8RD T568-35A

44 Model K Shear Safety Joint The T569 Model K Shear Safety Joint provides for emergency release of the tubing string. Straight pull separates the tool at a predetermined shear value. The Model K Shear Safety Joint allows torque to be transmitted through the tool without affecting the shear screws. Available in premium materials. Available with premium thread connections. Shear value field adjustable. Additional sizes available on request. Model "K" Shear Safety Joint (60.33) (77.90) (50.42) T569-20A (73.03) (92.46) (63.12) T569-25A (88.90) (114.55) (75.82) T569-35A (114.30) (139.70) (101.22) T569-45A

45 Telescoping Swivel Joint The TEAM T572 Telescoping Swivel Joint is designed for use in multi string packer completions to facilitate their assembly. It allows easy makeup of the tubing by allowing both rotation and telescoping of its top and bottom sub relative to each other. The standard tool can telescope up to 24 inches but it can be furnished in various lengths, upon request to suit specific completion requirements. Available in N-80 or L-80 material as standard, premium materials supplied on request. Available with API threads as standard but premium threads can be provided as needed. Nitrile seals are supplied as standard but premium seals are available as required. Standard telescoping length is 24 inches. Telecoping Swivel Joint Stroke length (60.33) (77.93) (50.42) (609.60) T572-20A (60.33) (77.93) (50.42) (914.40) T572-20A (60.33) (93.29) (63.12) (609.60) T572-25A (73.03) (93.29) (63.12) ( ) T572-25A

46 PBR The T-585 TEAM PBR Polished Bore Receptacle is used in a well completion to provide a means of sealing the tubing to the top of the production packer while maintaining maximum ID. It can accept either a latching type or locator seal assembly. It is made up to the top of the packer and provides an upper seal bore to allow tubing retrieval without releasing the packer. The PBR is run with the seal assembly in place. Following tubing retrieval, the PBR can be released from the packer using the pulling tool and right-hand rotation. Available with premium thread down. Available in premium materials. Equipped with standard nitrile seals. Premium seals available upon request. Upper Right-hand box thread to allow right-hand rotation to release PBR from the packer. After packer setting and testing the locator seal assembly is released by straight pull on the tubing to shear the screws and allow space out. Can accommodate locator seal assemblies. Available in 5, 10, 15 and 20 foot lengths. Allows tubing retrieval while leaving the packer and PBR in place. Allows subsequent PBR retrieval with right-hand rotation pulling tool. PBR PBR Length Feet (m) max stroke length Feet (m) (120.65) (146.05) (98.43) (1.594) (1.067) T (120.65) (146.05) (98.43) (3.048) (2.591) T (120.65) (146.05) (98.43) (4.572) (4.115) T (120.65) (146.05) (98.43) (6.096) (5.639) T

47 Packer Tubing Accessories The T597 Model A Pump-out Plug Assembly is used below a production packer or tailpipe. The assembly holds pressure from below and unseats with a predetermined amount of tubing pressure. T597 Model A Pump-Out Plug Thread Connection Inches The T597 Model A Pump-out Plug Assembly is used below a production packer or tailpipe. The assembly holds pressure from below and unseats with a predetermined amount of tubing pressure. The AR pump out plug assembly is recommended when running into liners or highly deviated wells. T597 Model A Pump-Out Plug Thread Connection Inches EUE (56.40) (31.75) EUE (63.50) (38.10) EUE (77.80) (50.80) EUE (95.25) (63.50) EUE (114.30) (76.20) EUE (56.40) (31.75) EUE (63.50) (38.10) EUE (77.80) (50.80) EUE (95.25) (63.50) EUE (114.30) (76.20) The T597 Model A Pump-out Plug Assembly is used below a production packer to test tubing integrity or to activate a hydraulic set packer. The Model ES allows fluid flow from both directions until a 1-3/8 Diameter ball is gravitated down into the landing seat. Pressure applied to tubing string will shear out ball and seat at a predetermined pressure rating. T597 Model A Pump-Out Plug Thread Connection Inches Seat I.D. Body I.D EUE (82.55) (25.00) (25.40) EUE (107.95) (30.00) (30.15) EUE (114.30) (31.75) (30.15) 44

48 Wireline Adapter Kit F/ASI-X, PATRIOT & Scorpion Retrievable Packers The T598 Wireline Adapter Kit is used as the interface between the Patriot or the ASI- XW retrievable packer to enable them to be set in place using standard pressure setting assemblies. Setting on electric wireline, using the combination of a power charge and a pressure setting assembly, enables packer to be accurately located in the well by correlating their position with well logs. May be set with industry standard E-Line or Hydraulic Setting Tools. Simple to install with only three major parts no special tools required. Allows packer placement in a much shorter time than by using tubular conveyed methods. Wireline Adapter Kit Use With Packer Setting TOol (88.90) (70.35) ASI-XW GO T598-35A (101.60) (80.95) ASI-XW E-4, #10 T598-40A (114.30) (92.86) ASI-XW E-4, #10 T598-45B (114.30) (95.38) ASI-XW E-4, #10 T598-45A (114.30) (95.38) Patriot / Scorpion E-4, #10 T598-45A (127.00) (95.25) Patriot / Scorpion E-4, #10 T598-50C (139.70) (114.71) ASI-XW E-4, #20 T598-55A (139.70) (111.91) ASI-XW E-4, #20 T598-56E (139.70) (114.71) ASI-XW / Patriot E-4, #20 T598-56A (177.80) (114.71) ASI-XW / Patriot E-4, #20 T598-70A (177.80) (139.70) Patriot E-4, #20 T598-73A (219.08) (140.11) Patriot E-4, #20 T598-86A (244.48) (158.88) Patriot E-4, #20 T598-95A

49 VIPER II Composite Bridge & Frac Plug The VIPER II utilizes a unique combination of composite components to provide a dependable, durable and cost-effective design for temporary zone isolation during stage fracs in both vertical and horizontal wells. VIPER II plugs are constructed primarily from molded or machined composites, with cast iron slips, ensuring fast drill time while remaining highly reliable. The VIPER II is a multi-configuration plug that allows a user to convert the tool from a Ball Drop to a Caged Ball or Bridge plug in minutes. This conversion is easily accomplished using hand tools and simple kits (Bridging Pin or Caged Ball Assembly). The setting sleeve and shear adapter are designed to be run on any wireline setting tool or tubing-run hydraulic setting tool, with Baker #10, Baker #20, or G.O. connections. The two piece setting sleeve utilizes an adjuster nut that mates directly to the setting tool. The shear sleeve adapter is also designed to allow the drop ball to be placed inside the adapter. This gives the user the choice to utilize the plug in the flow back configuration without having to drop and pump the ball down from the surface. Available in 4.500, and Other sizes pending. Standard plug is 10K: 6K & 8K rated versions also available. Sets securely in casing up to P-110 grade. Consistent drill times of minutes or less. Utilizes unique lug design on the top and muleshoe bottom ensuring plugs do not spin during drill out. Can be drilled out using conventional rigid tubing or coiled tubing. Materials used in construction are conducive to a wide range of environments. Slips are hardened to wicker depth only for ease of drill out. Pump down wiper available upon request. 46