Shuttlelift CD3300 Series Product Guide

Transcription

1 Shuttlelift CD3 Series Product Guide Features CD33F: 7,7 t (. USt) threesection boom with 7, m (2 ft 2 in) tip height CD33FL: 7,7 t (. USt) threesection boom with,2 m (33 ft in) tip height CD3339:,1 t (9 USt) threesection boom with 11, m (3 ft 2 in) tip height CD33B: 9, t (. USt) threesection boom with 11, m (3 ft 2 in) tip height 1, m ( ft) fixed extension (CD33F/ CD33FL) and 3, m ( ft) offsettable swingaway extension (CD3339 and CD33B) 74, kw ( bhp) Tier IV Cummins diesel engine or 9, kw ( bhp) GM EFI dual fuel engine

2 Features Pivoting boom nose Standard on the CD3339 and CD33B the exclusive pivoting boom nose allows operators to decrease the overall boom head depth and operate in more confined areas. Steering Standard: Twowheel, fourwheel, and crab steer with electronic self alignment (CD33B). Standard: Twowheel, fourwheel, and crab steer on other CD3 Series models. Optional: Electronic selfalignment on other CD3 Series models. Boom Standard:,4 m (21 ft) main boom on the CD33F. 9,1 m ( ft) main boom on the CD33FL., m ( ft in) main boom on the CD3339 and CD33B. Optional: Manual fourth main boom section adds 3, m ( ft) additional main boom length on CD33F and CD33FL only. Cab Standard: Open air cab shell with overhead safety glass. Optional: Closed cab with split hinged door, heater/defroster, and all window glass. Engine (Tier IV) Standard: Cummins QSB 3.3 L turbocharged diesel rated at 74, kw ( bhp) at rpm. Contents Specifications 4 CD33F (dimensions/range diagram/load chart) 7 CD33FL (dimensions/range diagram/load chart) CD3339 (dimensions/range diagram/load chart) 1 CD33B (dimensions/range diagram/load chart) 1 Symbols glossary 21

3 Specifications Specifications Superstructure Superstructure continued Load indicator (wireless LSI) Outrigger controls Boom CD33F: 2,9 m, m (9 ft in 21 ft 2 in) three section full power boom. Maximum tip height: 7, m (2 ft 2 in) CD33FL: 3, m 9,2 m ( ft in ft 2 in) three section full power boom. Maximum tip height:,2 m (33 ft in) CD3339 and CD33B: 4,2 m, m (13 ft in ft in) threesection full power boom. Maximum tip height: 11, m (3 ft 2 in) *Optional boom CD33F and CD33FL: Manual fourth main boom fly section adds 3, m ( ft) additional boom length. *Boom extension CD33F and CD33FL: 1, m ( ft) fixed pin on extension CD3339 and CD33B: 3, m ( ft) offsettable extension. 3, m,4 m ( ft 1 ft) telescopic offsettable extension Boom nose CD33F and CD33FL: Single sheave nonpivoting CD3339 and CD33B: Single sheave, threeposition (, +, + ) pivoting boom nose for minimizing head space requirements. Lowers head height., m (. in) when nose is pivoted fully forward. Boom elevation Single double acting hydraulic cylinder with integral holding valve. Elevation: to for the CD33F / FL. to 72 for the CD3339 and CD33B Antitwo block device Standard antitwo block device, when activated, provides an audible warning to the crane operator and disengages all crane functions whose movement can cause twoblocking. A simple, effective, and easy to use load indicating system used in conjunction with the antitwo block system to assist the operator in efficient operation of the unit within the limits of the load chart. The display panel displays the hook load and warns the operator when a preset load capacity is exceeded. The warning is by a flashing light on the display panel. In conjunction with the load display panel (receiver), there is a wireless transmitter and load sensing pin attached to the boom head that transmits the hook load to the display panel. *Load Moment Indicator (hardwired LMI) Digital display of boom angle, boom length, boom radius, capacity, and allows for operator input to set the limits based on load chart. Displays color coded light bar and audible alarm with function cutout if load exceeds entered parameters. Swing Ball bearing swing circle with 3 continuous rotation. Hydraulic driven worm gear and pinion. Maximum speed: 2. rpm Hydraulic system CD33F / FL: (2) gear pumps CD3339 and CD33B: Variable displacement piston pump and piggyback gear pump. Combined flow: 7,9 Lpm (2. gpm) Maximum system operating pressure: 3 psi CD33F/FL and CD3339: Six section valve bank mounted in dash panel with direct mechanical linkage for low effort lever control. CD33B: Six section valve bank chassis mounted; operated via dash mounted, pilot pressure hydraulic joysticks. Return line filter with full flow bypass protection and service indicator. 17 L (4 gal) hydraulic reservoir with sight level gauge and steel side plating to guard against side impact damage. 4 *Denotes optional equipment Shuttlelift CD3 Series *Denotes optional equipment Carrier Hoist specifications CD33F / FL: Worm drive with counterbalance valving. Equal speed power up and down. CD3339 and CD33B: Piston motor drive with spring applied/hydraulic released brake. Drum diameter: CD33F / FL:, m (9.9 in) CD3339 and CD33B:,27 m (.3 in) Maximum single line pull: CD33F / FL: 44 kg (,7 lb) CD3339 and CD33B: kg (, lb) Maximum single line speed: CD33F / FL:, m/min ( fpm) CD3339 and CD33B: 3, m/min (1 fpm) Maximum permissible single line pull: CD33F / FL: 3 kg (, lb) (,7 mm [1/2 inch] Python Ultra XIPS) CD3339 and CD33B: 43 kg (, lb) (, mm [9/ inch] EEIPS) Rope length : CD33F / FL: (threesection boom): 29, m (97 ft) (foursection boom): 39, m (1 ft) CD3339 and CD33B: 3, m (1 ft) Frame High strength alloy steel constructed with integral outrigger housings; front and rear lifting, towing, and tiedown lugs. 3 ft 2 carrydeck size with kg (, lb) carrying capacity (CD33F, CD33FL and CD3339) and 7711 kg (17, lb) carrying capacity (CD33B). Deck coated with antiskid treatment. Outriggers CD33F, CD33FL and CD3339: Front and rear oblique type beams at all four corners with integral holding valves. Outrigger pads form an integral part of the beam. CD33B: Hydraulic telescoping beam with oblique type jack provides extended and down and retracted and down lifting capacities. Integral holding valves on both beam and jack. Padsize CD3 Series: 1 cm x cm (7.4 in x 7. in) Maximum outrigger pad load: CD3F/FL: 2 psi CD3339: 13 psi CD33B: 37 psi CD33F, CD33FL: Lever controls located on dash panel which operate the beams in pairs from side to side. *Independent outrigger controls available as an option. CD3339: Lever controls located on dash panel which operate the beams independently. CD33B: Two switch operation mounted on dash panel. One three position rocker switch to select individual beams or jacks. Separate four way toggle switch to activate beams out/in and jacks down/ up. Level bubble indicator located inside operators compartment. Engine (Tier IV) Cummins QSB 3.3 L, fourcylinder, turbocharged diesel rated at 74. Kw ( hp) at rpm. Standard 1 V engine block heater and cold weather intake grid heater. Diesel oxidation/catalyst, stainless steel muffler/exhaust system to meet EPA emissions, combined with a Cummins direct air flow, twostage cyclonic air filter system. Maximum torque: 413, Nm ( lb ft) Note: Required for sale in North American and European Union countries. Standard engine (Tier III) Cummins QSB 3.3 L turbocharged diesel rated at 3,4 kw ( bhp) at rpm. Supplied with 1 V engine block heater and air intake grid heater. *Optional engine G.M. 3. L EFI dual fuel (gasoline / L.P.) rated at 9, kw ( bhp) at rpm. Operators control station Frame mounted, open air style control station with cab shell. Includes all crane functions, driving controls, and overhead safety glass. Other standard equipment include a durable weather resistant seat with seat belt, hourmeter, sight level bubble, and fire extinguisher. The dash panel includes engine oil pressure gauge, engine water temperature gauge, fuel gauge, transmission low oil and high temperature warning lights, low battery warning light, and brake system low pressure warning light.

4 Specifications Dimensions Carrier continued Brakes CD33F *Operators control station enclosed Includes the standard cab shell with the addition of front, right, and rear glass, a split (twopiece) hinged door with sliding glass. Front windshield wiper and heater and defroster is included. Fuel tank capacity 4 L (17 gallon) all steel construction with steel side plate to guard against side impact. Hydraulic actuated internal wetdisc service brakes acting on all four wheels. A dash mounted toggle switch activates the dry disc parking brake on the transmission output yoke with a dash warning light. Suspension Front: Rigid mounted to frame. Rear: Rigid mounted to frame. Lights 1, m (4' 2."), m (1' 1 1."), m (3.") 2,1 m (' 7.") 1,11 m (3' 7.7"),99 m (3' 3") 1,33 m (' 1 1.") Electrical system One V maintenance free battery, CCA at. Jump start connections. 1 amp alternator. Drive 4 x 2 Front axle drive with planetary hubs and limited slip differential. Steer CD33F/FL/ CD3339: twowheel, fourwheel with crab steer CD33B: twowheel, fourwheel, and crab steer with electronic self alignment. Transmission CD33F, CD33FL, CD3339: Synchromesh fourspeeds forward and reverse with stalk mounted forward/ reverse selector. CD33B: Powershift four speeds forward and reverse. Stalk mounted shifter on left side of steering column. Axles Recessed mounted, includes head, tail, rear work, stop, and turn signals. 3, km/h ( mph) Maximum speed Gradeability (theoretical) CD33F, CD33FL, CD3339: 7%...no load 31% kg (, lb) load CD33B: %...no load % kg (, lb) load Gross vehicle weight (G.V.W.) CD33F: 7231 kg (1,941 lb) CD33FL: 7 kg (17,31 lb) CD3339: 21 kg (17,3 lb) CD33B: 3 kg (1,3 lb) *All weights with enclosed cab and Tier IV engine Miscellaneous standard equipment Single sheave, Quick Reeve style hook block.; CD33F and CD33FL:, t (. USt) CD3339 and CD33B: t (. USt) Backup alarm 1, m (3' 3."),4 m (1' ") 2,39 m (7' ") 1,77 m (' 9.7") 1,74 m ('.3") 3,4 m (' 7") 2,3 m (' ") 1,2 m (' 1 1."), m (1' ") On tires,2 m (9.") 3, m (11' 11.7") 1, m (3' 4."),97 m (3' 2") 1,74 m ('.3") 1,7 m (3' "), m (1' ") Front: Carraro planetary drive/steer with internal multiwetdisc brakes and limited slip differential. Rear: Fabricated nondrive steer with disc brakes Tires. x 1 pneumatic 1, m (' 3") 1,99 m ('.2") 3, m (' 2") 1,93 m (' 4") 2,1 m (9' 2.7") *Denotes optional equipment Shuttlelift CD3 Series 7

5 Turning radius Range diagram CD33F CD33F SECTION 4SECTION ' jib Boom and extension length in feet Height from the ground in feet B A C Twowheel steer 449 mm ( ft 9 in) Fourwheel steer 4 mm ( ft in) D A B C D E 4737 mm (1 ft. in) 34 mm (11 ft 9. in) 43 mm (1 ft 2. in) 31 mm ( ft. in) E 271 mm ( ft 11 in) 73 mm (4 ft in) 2 mm (1 ft 1. in) 39 mm (11 ft. in) Operating radius in feet from axis of rotation Shuttlelift CD3 Series 9

6 Load chart Dimensions CD33F CD33FL RADIUS 3SECTION OR 4SECTION WITH 4TH RETRACTED ON OUTRIGGERS (lb) ON RUBBER (lb) F/R 3 F/R 3 1, m (4' 2."), cm (."), m (1' 11."), m (3.") 3,7 m (' 4") Retracted 9,21 m (' 2.") Extended,99 m (3' 3") 1,4 m (4' 9.13") 1,3 m (' ") JIB. 17, 17,. 1,7,.,,., ,, , RADIUS 4SECTION WITH 4TH EXTENDED ON OUTRIGGERS (lb) ON RUBBER (lb) F/R 3 F/R MAIN ANGLE (deg) JIB STRUCTURAL CAPACITIES (lb) 3SECTION OR 4SECTION WITH 4TH RETRACTED SECTION WITH 4TH EXTENDED * LIMIT TO 11, LB WHEN 3RD SECTION IS EXTENDED ANY AMOUNT. 1, m (3' 3.") NOTES: JIB CAPACITY IS LIMITED BY BOTH STRUCTURAL CAPACITY CHART AND MAIN CAPACITY CHART. SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING. OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY. 1 FRONT REAR MAIN BLOCK HOOK & BALL JIB, STOWED JIB, DEPLOYED 1P ART lb REDUCTION CHART 1 lb lb lb lb RIGGING CHART 2PART 17, lb WIRE ROPE: 1/2 inch diameter Min. breaking strength 29,7 lb JIB N/A lb N/A lb 1 1) The rated loads are the maximum lift capacities as determined by operating radius, boom extension and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied. 2) The rated loads shown on outriggers do not exceed % of actual tipping. The rated loads shown on rubber do not exceed 7% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator. 3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See reduction chart. 4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting. ) Ratings on rubber depend on tire capacity, condition of tires and proper inflation pressure ( psi). Loads on rubber may be transported at a maximum seed of 2. mph on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. ) For operating radius not shown, use load rating of next larger radius. 7) The maximum combined total boom and deck load is, lb. The maximum deck load only is, lb. ) Do not induce any external side loads to boom or jib. CD 2,39 m (7' "),4 m (1' ") 1,77 m (' 9.7") 1,74 m ('.3") 4,7 m (1' 7.") 3, m (' 2") 2,3 m (' ") 1,2 m (' 11."), m (1' "),2 m (9' ") On tires 1, m (' 3") 1,99 m ('.2"),97 m (3' 2") 1,93 m (' 4") 2,1 m (9' 2.7") 3, m (11' 11.7") 1, m (3' 4.") 1,74 m ('.3") 1,7 m (3' "), m (1' ") Shuttlelift CD3 Series 11 * * * * *

7 Turning radius Range diagram CD33FL CD33FL (Threesection boom) '4" 17'." '2." 3'2." WITH '" JIB ' JIB Boom and extension length in feet Height from the ground in feet B A C Twowheel steer 131 mm ( ft in) Fourwheel steer 33 mm ( ft 1 in) D A B C D E 4737 mm (1 ft. in) 34 mm (11 ft 9. in) 43 mm (1 ft 2. in) 31 mm ( ft. in) E 271 mm ( ft 11 in) 73 mm (4 ft in) 2 mm (1 ft 1. in) 39 mm (11 ft. in) Operating radius in feet from axis of rotation Shuttlelift CD3 Series 13

8 Range diagram Load chart CD33FL (Foursection boom) CD33FL (Threesection boom) ' JIB '4" 21'" '7" 39'" 4'" WITH '" JIB 2 1 Boom and extension length in feet Height from the ground in feet Operating radius in feet from axis of rotation SECTION ON OUTRIGGERS (lb) F/R 3 17, 1,7,, ,,, NOTES: OPERATE WITH JIB BY RADIUS WHEN MAIN IS FULLY EXTENDED AND BY ANGLE WHEN IS PARTIALLY EXTENDED. DO NOT EXCEED JIB CAPACITIES AT ANY PARTIALLY EXTENDED LENGTH. SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH. DO NOT RELY ON TIPPING. OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY. 1 FRONT REDUCTION CHART REAR JIB SECTION ON RUBBER (lb) F/R 3, , ) The rated loads are the maximum lifting capacities as determined by operating radius only. Any combination of boom lengths and angles may be used to obtain operating radius. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied. 2) The rated loads shown on outriggers do not exceed % of actual tipping. The rated loads shown on rubber do not exceed 7% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform, supporting surface. Practical working loads depend on supporting surface, operating radius, and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel, and proper training must all be taken into account by the operator. 3SECTION W/ FT JIB DEPLOYED LOADED ON OUTRIGGERS (lb) ON RUBBER (lb) ANGLE (deg) F/R 3 F/R ) Ratings on outriggers are with outriggers fully extended. ) Ratings on rubber depend on tire capacity, condition of tires and proper inflation pressure ( psi). Loads on rubber may be transported at a maximum speed of 2. mph on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. ) For operating radius not shown, use load rating of next larger radius. 7) The maximum combined total boom and deck load is, lb. The maximum deck load only is, lb. ) Do not induce any external side loads to boom or jib. 1779CD MAIN BLOCK HOOK & BALL JIB, STOWED JIB, DEPLOYED 1 lb N/A lb lb lb N/A lb lb 3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered as part of the load. See reduction chart. RIGGING CHART 1PART lb 2PART 17, lb WIRE ROPE: 1/2 inch diameter Minimum breaking strength 29,7 lb Shuttlelift CD3 Series 1

9 Load chart Dimensions SECTION W/ 4TH RETRACTED ON OUTRIGGERS (lb) ON RUBBER (lb) F/R 3 F/R CD33FL (Foursection boom) 4SECTION W/ 4TH EXTENDED ON OUTRIGGERS (lb) ON RUBBER (lb) F/R 3 F/R NOTES: OPERATE WITH JIB BY RADIUS WHEN MAIN IS FULLY EXTENDED (WITH 4TH SEC TION EXTENDED OR RETRACTED) AND BY ANGLE WHEN IS PARTIAL LY EXTENDED. DO NOT EXCEED JIB CAPACITIES AT ANY PARTIALLY EXTENDED LENGTH. SHADED AREAS ARE GOVERNED BY STRUC TURAL STRENGTH. DO NOT RELY ON TIPPING. OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY. See Insert CD3339 Retracted 4, m & Extended,1 m (Retracted 13 & Extended ) 3, m ( ) 3,39 m (11. ),1 m (2 2 ) 1, m (4 4 ) 394 m (1. ) SECTION W/ 4TH RETRACTED W/ FT JIB DEPLOYED LOADED ON OUTRIGGERS (lb) ON RUBBER (lb) ANGLE (deg) F/R 3 F/R FRONT MAIN BLOCK HOOK & BALL JIB, STOWED JIB, DEPLOYED REDUCTION CHART REAR JIB 1 lb N/A lb lb lb N/A lb lb RIGGING CHART 1PART lb 2PART 17 lb WIRE ROPE: 1/2 inch diameter Minimum breaking strength 29,7 lb SECTION W/ 4TH EXTENDED W/ FT JIB DEPLOYED LOADED ON OUTRIGGERS (lb) ON RUBBER (lb) ANGLE (deg) F/R 3 F/R ) The rated loads are the maximum lifting capacities as determined by operating radius only. Any combination of boom lengths and angles may be used to obtain operating radius. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied. 2) The rated loads shown on outriggers do not exceed % of actual tipping. The rated loads shown on rubber do not exceed 7% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform, supporting surface. Practical working loads depend on supporting surface, operating radius, and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel, and proper training must all be taken into account by the operator ) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered as part of the load. See reduction chart. 4) Ratings on outriggers are with outriggers fully extended. ) Ratings on rubber depend on tire capacity, condition of tires and proper inflation pressure ( psi). Loads on rubber may be transported at a maximum speed of 2. mph on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. ) For operating radius not shown, use load rating of next larger radius. 7) The maximum combined total boom and deck load is, lb. The maximum deck load only is, lb. ) Do not induce any external side loads to boom or jib , m (43. ) 1,34 m (3. ) *1,37 m (4. ) * boom head position can only be used with a down haul block 1,7 m (.92 ) Dimensions are with boom horizontal and the antitwo block bottomed.,4 m (1 ),3 cm (2. ) Dimensions are with boom horizontal and the antitwo block bottomed. 1,3 m (3 4. ) 1.74 m (.3 ) 1,74 m ( 11. ), m (1 ) 2,3 m (' "),9 m (3 2. ) 1, m ( 3 ) 1,9 m ( ) 3, m ( 2 ) 1,1 m (9 2.7 ) 1, m (3 4. ) 3, m ( ) 1,74 m (.3 ) 1,77 m ( 9.7 ), m (1 ) 2,21 m (7 3 ) Shuttlelift CD3 Series 17

10 Turning radius Range diagram CD3339 CD , m (' ") boom with 3, m (') to,49 m (1') telescopic offsettable boom extension 13,7 m (44' ") boom with 3, m (') offsettable boom extension A B C D E , m (' ") boom 7,11 m (23' 4") boom 4, m (13' ") boom Twowheel steer 474 mm ( ft 4 in) Fourwheel steer 47 mm ( ft in) A B C D E 4737 mm (1 ft. in) 34 mm (11 ft 9. in) 43 mm (1 ft 2. in) 31 mm ( ft. in) 271 mm ( ft 11 in) 73 mm (4 ft in) 2 mm (1 ft 1. in) 39 mm (11 ft. in) 4 ' Jib 1' Jib Shuttlelift CD3 Series Boom and extension length in feet Height from the ground in feet Operating radius in feet from axis of rotation

11 Load chart Dimensions CD3339 CD33B 1 FRONT MAIN BLOCK HOOK & BALL JIB, STOWED JIB, DEPLOYED RADIUS NOTES: JIB CAPACITY IS LIMITED BY BOTH STRUCTURAL CAPACITY CHART AND MAIN CAPACITY CHART. SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING. OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY. 1PART, lb RETRACTED REDUCTION CHART 1 lb lb 1, 1,7,, REAR MAIN JIB N/A lb lb N/A lb lb RIGGING CHART F/R WIRE ROPE: 9/ in diameter Min. breaking strength 3, lb ON OUTRIGGERS (lb) ON RUBBER(lb) 3 F/R 3 EXTENDED,7,,, PART 1, lb 1 RETRACTED 1, 1, 11, 9 7 EXTENDED,7, 11, ANY 11,, ANY JIB 1) The rated loads are the maximum lifting capacities as determined by operating radius only. Any combination of boom lengths and angles may be used to obtain operating radius. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied. 2) The rated loads shown on outriggers do not exceed % of actual tipping. The rated loads shown on rubber do not exceed 7% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform, supporting surface. Practical working loads depend on supporting surface, operating radius, and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel, and proper training must all be taken into account by the operator. 3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered as part of the load. See reduction chart. MAIN ANGLE (deg) JIB STRUCTURAL CAPACITIES (lb) ft JIB 1 ft JIB ) Ratings on outriggers are with outriggers fully extended. ) Ratings on rubber depend on tire capacity, condition of tires and proper inflation pressure ( psi). Loads on rubber may be transported at a maximum speed of 2. mph on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. ) For operating radius not shown, use load rating of next larger radius. 7) The maximum combined total boom and deck load is, lb. The maximum deck load only is, lb. ) Do not induce any external side loads to boom or jib CD See Inset *1372 mm (4") o o o * o boomhead position can only be used with headache ball. 134 mm (3") 1 mm (43.") 1,3 m (' ") 3, m (11' 7.7") Main block twopart line Hook and ball onepart line 1,3 m (' 4.1") Dimensions are with the boom horizontal and the antitwo block bottomed. 2,21 m (7' 3.") Retracted 4, m (13'") and Extended,1 m (' ") 2,1 m (7' 2.") 3,49 m (11'.") 1,7 m ('.") 1,77 m (' 9.") 1,9 m (' 2.") 2,1 m (' 7.") mm (") 3, m (' ") 1, m (3' 9.") mm (") 1, m (' 3.") Track Width 1,93 m (' 4.") Frame Width 2,1 m (' 7.") Max. Machine Width 2, m (' 9.") C.L.O.R. Ret. and Down 3, m (11' 2.") C.L.O.R. Ext. and Down 9 mm (37") 1, m (4' 4.") 1,4 m (' 4.") 394 mm (1.") mm (") 1, m (3' 3.") Shuttlelift CD3 Series 21

12 Turning radius Range diagram CD33B CD33B A B C Outside turning radius Twowheel steer 479 mm (1 ft 7.4 in) Fourwheel steer 399 mm (13 ft 1.1 in) A B C D E 442 mm ( ft.4 in) 334 mm ( ft 11.7 in) D Inside turning radius mm (13 ft 4. in) 23 mm (9 ft 4.3 in) mm ( ft 4. in) 7 mm (4 ft 9.9 in) E 4 mm ( ft. in) 34 mm (11 ft 2. in) '" JIB 13'" 23'4" '" 44'" WITH '" '" WITH JIB & '" STINGER 1 Boom and extension length in feet Height from the ground in feet Operating radius in feet from axis of rotation Shuttlelift CD3 Series 23

13 Load chart CD33B RADIUS RETRACTED ON OUTRIGGERS (lb) ON RUBBER (lb) JIB STRUCTURAL CAPACITIES (lb) MAIN RETRACTED 3 F/R 3 ft JIB 1 ft JIB ANGLE (deg) NOTES: JIB CAPACITY IS LIMITED BY BOTH STRUCTURAL CAPACITY CHART AND MAIN CAPACITY CHART. SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING. OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY. 1) The rated loads are the maximum lifting capacities as determined by operating radius, boom extension and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading to the center of vertical hoist line or tackle with load applied. 2) The rated loads shown on outriggers do not exceed % of actual tipping. The rated loads shown on rubber do not exceed 7% of actual tipping. Retracted outrigger rated loads meet ASME B.4. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform, supporting surface. Practical working loads depend on supporting surface, operating radius, and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel, and proper training must all be taken into account by the operator. 3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered as part of the load. See reduction chart. 4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting. ) Ratings on rubber depend on tire capacity, condition of tires and proper inflation pressure ( psi). Loads on rubber may be transported at a maximum speed of 2. mph on a smooth, hard level surface with boom retracted to the shortest length possible and centered over front. ) For operating radius not shown, use load rating of next larger radius. 7) The maximum combined total boom and deck load is, lb. The maximum deck load only is, lb. ) Do not induce any external side loads to boom or jib. CD Load distribution chart Shuttlelift CD3 Series 2 JIB EXTENDED 3 RETRACTED F/R 21, 1, 1,7,, EXTENDED 1,,7,,, ANY ANY RETRACTED EXTENDED 19,2, 13, 7 13,97 13,7 13, , 11, 11, 9, FRONT REAR MAIN BLOCK HOOK & BALL JIB, STOWED JIB, DEPLOYED REDUCTION CHART RIGGING CHART 1PART, lb 1 lb lb lb lb WIRE ROPE: 9/ inch diameter Min. breaking strength 3,7 lb JIB N/A lbs N/A lb 1 2PART 21, lb AREA 1 2,37 m sq (2. sq ft) 2 kg (9 lb) AREA 2 1,43 m sq (1.4 sq ft) kg ( lb) 1) Maximum travel speed with any or all loads 4, km/h (2. mph) 2) Loads to be transported on smooth level surfaces only. 3) Boom must be retracted and in center forward position. 4) Any combination or total of areas 1 and 2 may be used. ) Lifting is not permitted when carry deck is loaded except for loading and unloading carry deck. ) Rated pick and carry loads may be transported on deck area 1 provided the load is cribbed directly on the frame rails. Area 2 Area 1 Engine hood Frame rails Cab Hydraulic reservoir

14 Symbols glossary Axles Counterweight Grade Outriggers Boom Drive Heavy duty jib Boom elevation Electrical system Hoist Rotation Boom extension Engine Hookblock H Speed Boom length Extension Hydraulic system Steering Boom nose Frame Lights Suspension Brakes Fuel tank capacity Oil Swing Cab Gear Outrigger controls Tires Transmission Notes Shuttlelift CD3 Series 27

15 Manitowoc Cranes Regional headquarters Americas Manitowoc, Wisconsin, USA Tel: Fax: Shady Grove, Pennsylvania, USA Tel: Fax: Europe, Middle East, Africa Ecully, France Tel: +33 () Fax: +33 () China Shanghai, China Tel: Fax: Greater AsiaPacific Singapore Tel: Fax: + 2 Regional offices Americas Brazil Alphaville Mexico Monterrey Chile Santiago Europe, Middle East, Africa France Baudemont Cergy Decines Germany Langenfeld Italy Lainate Netherlands Breda Poland Warsaw Portugal Baltar Russia Moscow South Africa Johannesburg U.A.E. Dubai U.K. Buckingham China Beijing Chengdu Guangzhou Xian Greater AsiaPacific Australia Brisbane Melbourne Sydney India Chennai Delhi Hyderabad Pune Korea Seoul Philippines Makati City Singapore Factories Brazil Passo Fundo China TaiAn Zhangjiagang France Charlieu Moulins Germany Wilhelmshaven India Pune Italy Niella Tanaro Portugal Baltar Fânzeres USA Manitowoc Port Washington Shady Grove This document is noncontractual. Constant improvement and engineering progress 13 Manitowoc Form No. CD3 Series PG Part No.2M1113