Fully Hydraulic Crawler Spanner Crane

Transcription

1 Fully Hydraulic Crawler Spanner Crane Lifting Capacity 0 metric tons General Dimensions (with basic boom) (Unit: mm) Center of rotation Min (Top clearance) 4230 (at -frame folded) 371 (Rear-end swing radius) Basic boom length 3180 Cab width 20(In operation) 320(at -frame folded) 1110 Boom foot 160 G.L Working radius (In operation) 290(In transport) 430(In operation) 3300(In transport) Specification Performance Swing speed Travel speed Gradeability Engine Make Model Type Water cooled, 4-cycle, direct fuel injection turbocharged and charge air cooled Total piston displacement 6.7L Rated output 149kW/0rpm Fuel tank capacity 240L Battery V x 2pcs. Load hoist system(main&ux.) Hydraulic motor Reduction gear Hoist drum Clutch Brake Drum lock system Motor Reduction gear Hoist drum Brake Drum lock 3.rpm 1.6km/h(1mph) 40%(pprox.22) Cummins Inc. QSB6.7 Variable displacement axial piston type One-stage planetary gear and single stage spur gear Dual drums on inline individual shaft, independent hydraulic motor driven, lagging type with lebus grooved drum Internal expanding band type External contracting type Ratchet lock xial piston type Two stage planetary gear Lebus grooved drum utomatic spring-loaded hydraulically released wet type multi-disk Ratchet lock Travel speed changes depending on the load. Standard equipment Instrument Engine tachometer (Hour meter) Hydraulic oil pressure gauge (for control circuit) Fuel level gauge Engine coolant thermo indicator Engine oil pressure indicator Hydraulic oil thermo indicator Lighting indicated bar graph in OK monitor Work light 24v x 80w x 2 Room light 24v x 20w x 1 Safety device utomatic stop for hook overwinding utomatic stop for boom overwinding Telescopic boom limit stop Swing lock Main and ux. drum lock Safety valve for hydraulic circuit Counter balance valve Control lever locking device Standard accessories Windshield wiper Roof glass wiper Sunvisor Sun shade Storage pouch Reclining operator's sheat Floor mat Steps for operator's cab (foldable type) Radio Cigarette lighter sh tray Rearview mirrors (R/L) Horn Swing warning flasher Travel warning flasher Low-noise cab Bronze tinted glass Electrical engine throttle control Hydraulic assist brake (Main & ux. winch) Winch mode selector (main & ux. winch) Ultra low speed control Wire mesh boom walkway (for inner boom) Plug socket (24v) Fuel filling pump ""frame (High gantry) erecting device

2 Crane specifications Max.lifting capacity(metric ton) x working radius(m) Max.boom length,main(main+jib boom)(m) Main drum hoist/lowering(m/min) Rope speed ux.drum hoist/lowering(m/min) Boom drum hoist/lowering(m/min) Hook block capacity(ton) x part line Part line Hook block capacity(ton) x part line Boom drum hoist/lowering part line Counterweight(ton) Total operating weight(ton) Hook block capacity(ton) verage ground bearing pressure(kg/cm 2 ) T he rope speed changes depending on the load. Combination of main boom and jib boom Jib boom Main boom length(m) length(m) :pplicable combination Wire rope Place of use Main drum ux.drum Boom suspension Jib boom suspension Jib strut suspension Rope type :6XFi(29)IWRC regular Z lay B:6XWS(31)T IWRC regular Z lay Length of wire rope to be decided according to the ordered boom length Boom composition Standerd Boom length Rope diameter(mm)/guaranteed strength(ton) / /74.9 /49.9 /49.9 Boom composition 6.(inner)+.(outer) :R equired middle suspension for boom length 39m and longer 0 x 3.7 1(42+1) 100/70 0/3 100/70 0/ x 10.8 x Rope type B (Unit:m) Working range(no loaded condition) 1m Boom 48m Boom 4m Boom 42m Boom 39m Boom 36m Boom 33m Boom 30m Boom 27m Boom 24m Boom 21m Boom 18m Boom 1m Boom m Boom R m Jib 80 6m Jib 9m Jib 30 m Jib Hook clearance 3.8m 1m Jib Working radius (m) Jib offset angle Hook clearance 2.8m Height above ground (m) Jib Boom composition Jib Boom length Jib Boom composition 3(inner)+3(outer) (Unit:m)

3 Rated lifting loads (Unit:metric ton) Working radius(m) No.of Part Line mx m x m x mx m x m x mx m x.9mx m x mx m x 29.7m x 4 7.6mx mx m x mx mx mx m x Notes 1. bove rated loads are based on firm level ground, within 78% of tipping load at any point 360throughout and with front stability of 1.1 or more. 2. Working radius is horizontal distance from center of rotation to a vertical line through the centerline of gravity of the load. 3. The weight of the hook block and other lifting devices must be considered to be a part of the load. 0 ton hook lock0.49ton b 2 ton hook lock0.3ton b 1 ton hook lock0.31ton b 4. Crawler frame and frame (high gantry) should also be extended before working.. When jib boom is fitted actual loads that can be lifted with the main hook block should reduce following weights from the above chart (the weights include that of the auxiliary hook block). Jib boom length(m) Weight to be deducted(ton) Depending on the number of part lines, rated lifting load is limited as follows, 1-par t lineup to.8 tons 2-par t lineup to 11.4 tons 3-par t lineup to tons 4-par t lineup to tons -par t lineup to 2.0 tons 6-par t lineup to tons 7-par t lineup to 3.0 tons 8-par t lineup to 40.0 tons 9-par t lineup to 4.0 tons 10-par t lineup to 0.0 tons 7. The hook block will not come down to ground level, if the rope part line is more than shown in above chart.

4 Jib rated lifting loads Jib length(m) Offset angle Working radius(m) mx mx.mx 17.6mx 7.3mx 6.6mx 9.2mx 21.0mx 7.4mx 23.2mx 10.9mx 2.8mx.4mx 2mx mx mx 7.8mx 20.6mx 7.1mx 23.0mx mx 23.6mx 2.8mx mx 26.6mx (Unit:metric ton) 28.4mx.9mx 29.6mx Jib length(m) Offset angle Working radius(m) mx mx mx 8.3mx mx mx mx 10.3mx mx 8.4mx mx mx 31.0mx mx mx mx mx mx 8.3mx mx 8.2mx mx 10.8mx mx mx.mx mx 9.mx 33.6mx 2.2 Jib length(m) Offset angle Working radius(m) mx mx mx mx 8.7mx mx 11.3mx mx 9.mx mx 13.0mx mx mx mx mx mx mx 9.2mx mx 11.8mx mx mx mx 1.8

5 Jib rated lifting loads Jib length(m) Offset angle Working radius(m) mx mx 10.4mx mx mx mx mx mx mx (Unit:metric ton) mx 30.6mx mx mx mx mx mx mx mx Jib length(m) Offset angle Working radius(m) mx mx mx mx mx mx 11.6mx 1.1mx.1mx 16.mx mx mx mx mx 1.6mx.6mx 17.1mx Jib length(m) Offset angle Working radius(m) mx mx 2.7.mx mx mx 2.7.6mx mx mx 17.6mx mx mx mx mx mx mx Notes bove rated loads are based on firm level ground, within 78% of tipping load at any point 360 throughtout with front stability of 1.1 or more. Working radius is horizontal distance from center of rotation to a vertical line through the center of gravity of the load. When main hook block installed actual loads that can be lifted with the jib hook should reduced following weights from the above chart. 0ton hook block ton 2ton hook block...0.3ton 1ton hook block ton.8ton hook block...0.ton One part line jib hook lifting. Crawler frame and "" frame should also be extended before working. Jib boom can only be used crane operations. Main boom can only be used for crane operations when equipped with 6.0m 1.0m jib. ll rated loads are based on structural strength factors. Make sure to prevent overloading.

6 Working range(with 18m boom & 1.0m 3 bucket) (Unit: mm) Min. 400 (Bucket clearance) Center of rotation Boom length Tagline Boom angle3 6 Dumping height Total lift Boom foot G.L Working radius Digging depth Clamshell specifications Max.lift above ground(m) 13.3(18m boom + 1.0m 3 bucket) Bucket closing (m/min) 100/70 0/3 Rope speed Bucket holding (m/min) Bucket hoist and lowering (m/min) 100/70 0/3 60 Bucket closing 6(for all types bucket) Part line Bucket holding 1(for all types bucket) Rated lifting load(bucket+load) (ton) Counterweight (ton) 16 Total operating weight (ton) (Boom length 18m) 1.3 (Bucket capacity 1.0m 3 ) verage ground bearing pressure(kg/cm 2 ) (Boom length 18m) 0.6 (Bucket capacity 1.0m 3 ) : he T rope speed changes depending on the load. Working range and rated loads Boom length (m) Boom angle Working radius (m) Rated lifting load (metric ton) Total lift (m) Max.dumping height Bucket type(purpose) HD : Heavyduty (civill engineering, construction) GP : General purpose (heavy load handling) WR : Wide rehandling (medium load rehandling) Wire rope Place of use Bucket closing Bucket holding Boom suspension Tagline Rope diameter(mm)/guaranteed strength(ton) / /74.9 /. Rope type : 6xFi(29)IWRC regular Z lay B : 6xWS(31)T IWRC regular Z lay C : 6x(19)fiber core regular Z lay Length of wire rope to be decided according to the ordered boom length. Rope type B C Max.digging depth Notes 1. Rated loads are the upper limit of the "bucket weight+load" during clamshell work. Use a bucket suitable for the kind of the load required so that the rated load figures in the table are not exceeded. 2. The maximum digging height is for a standard 1.0 m 3 bucket. 3. The maximum digging depth is for standard wire rope length as follows. Closing 6m Holding 3m Tagline 0m Clamshell bucket specifications Classification Standard Type HD GP GP WR WR Capacity(m 3 ) Weight(ton)

7 Working range(with 18m boom & 1.0m 3 bucket) (Unit: mm) Center of rotation 1000 Boom foot Boom length Boom angle3 6 Min. 700 (Bucket clearance) Maximum dumping height G.L Working radius Maximum digging depth Maximum digging distance Dragline specifications Max.digging distance(m) Max.dumping height(m) Max.digging depth(m) Bucket hoist(m/min) Bucket digging(m/min) Rope speed and lowering (m/min) Bucket hoist Part line Bucket digging Counterweight (ton) Total operating weight (ton) (Boom length 18m) (Bucket capacity 1.0m 3 ) verage ground bearing pressure(kg/cm 2 ) (Boom length 18m) (Bucket capacity 1.0m 3 ) : he T rope speed changes depending on the load. 21.7(18m boom + 1.0m 3 bucket) 10.9(18m boom + 1.0m 3 bucket) 9.6(18m boom + 1.0m 3 bucket) 100/70 0/3 100/70 0/ Dragline bucket specifications Classification Standard LD GP : General purpose digging LD : Light digging, scraping Wire rope Place of use Hoist rope Drag rope Boom suspension Dump rope Rope diameter(mm)/guaranteed strength(ton) / /74.9 /19.2 Rope type : 6xFi(29)IWRC regular Z lay B : 6xWS(31)T IWRC regular Z lay C : T7x7+Fi(29)Toughsuper Length of wire rope to be decided according to the ordered boom length. One (1) Sheave type boom point is recommended to dragline work. Rope type C B Working range and rated loads Boom length (m) 1.0 Boom angle Working radius (m) Rated lifting load (metric ton) Max.digging distance(m) Max.digging depth(m) Max.digging height(m) Notes 1. Rated loads is the total of the bucket's deadweight and grabbed load's weight. The total weight of this must not exceed the value in the table above. 2. bove capacities are based on 1.0m 3 standard bucket. 3. The reach of bucket and digging depth differ according to the bucket size and type. in addition to the operational conditions. 4. bove working range is based on standard wire rope length as follows. Drag rope28m Hoist rope40m. Selection of the bucket type must be made according to the soil conditions. In particular do not use 1.2m 3 bucket for solid soil or clay soil. Type GP GP GP Capacity(m 3 ) Weight(ton)

8 General layout Min. 200mm (Top clearance) Center of rotation Guide sheave Cord reel Lifting magnet Tagline G.L Working radius Lifting magnet crane specifications Max. lifting capacity (metric ton) x working radius (m) Boom length (m) Magnet diameter (mm) Weight (ton) Voltage Generator capacity (kw/rpm) Ingot Lifting capacity (ton) Punched scrap Scrap Pig iron Operating weight with 18m boom and 100mm dia.magnet (ton) Counterweight (ton) verage ground bearing pressure (kg/cm 2 ) DC-220V 20/ x DC-220V 2/ Wire rope Place of use Load hoist Boom suspension Tagline Rope diameter(mm)/guaranteed strength(ton) / /74.9 /. Rope type : 6xFi(29)IWRC regular Z lay B : 6xWS(31)T IWRC regular Z lay C : 6x(19)fiber core regular Z lay Length of wire rope to be decided according to the ordered boom length. Rope type B C

9 Lifting magnet crane rated lifting loads. Working radius(m) No. of Part Line m x m x m x m x m x (Unit:metric ton) m x Notes 1. bove rated loads are based on firm level ground within 78% of tipping load at any point 360throughout and with front stability of 1.1 or more. 2. Crawler frame and frame (High gantry) should also be extended before working. 3. The weight of the hook block, magnet and other lifting devices must be considered to be a part of the load. Hook block weight. 3 ton0.3ton 2 ton0.3ton 1 ton0.31ton 4. Depending on the number of part line, rated lifting load is limited as follows. 2-part lineup to 11.4 tons 3-part lineup to tons 4-part lineup to tons -part lineup to 2.0 tons

10 General dimensions (Unit: mm) Center of rotation Min (Top clearance) Boom length Boom foot 3230 W.L Working radius bove figure is for reference when mounted crawler crane on pontoon as floating crane. Pontoon mounted crane specifications Max.lifting capacity(metric ton) x working radius(m) 3 x 4.8 Max.boom length 24m Main drum hoist/lowering 100/70 0/3m/min Rope speed ux.drum hoist/lowering 100/70 0/3m/min Boom drum hoist/lowering 60m/min Hook Block capacity(ton) 3 x 7 Part line x part line(m).8 x 1 Boom drum hoist/lowering Counterweight(ton) 16 Total operating weight with m boom (including crawler fixing device)(ton) 0.0 verage ground bearing pressure(kg/cm 2 ) 0.64 : he T rope speed changes depending on the load. Wire rope Place of use Main drum ux.drum Boom suspension Rope diameter(mm)/guaranteed strength(ton) / /74.9 Rope type : 6xFi(29)IWRC regular Z lay B : 6xWS(31)T IWRC regular Z lay Length of wire rope to be decided according to the ordered boom length. Rope type B

11 Pontoon mounted crane rated lifting loads.(throughout 360) Working radius(m) No. of Part Line m x m x m x m x m x m x m x m x m x.20 Notes 1. The working radius is horizontal distance from center of rotation to vertical line through the center line of gravity of the load. 2. The weight of the hook block and other lifting devices must be considered to be a part of the load. 0ton hook block0.49ton 3ton hook block0.3ton 1ton hook block0.31ton.8ton hook block0.ton 3. Do not exceed 3 of trim angle of pontoon on loaded condition. 4. Depending on the number of part lines, rated lifting is limited as follows. 1-par t lineup to.8 tons 2-par t lineup to 11.4 tons 3-par t lineup to 1.0 tons 4-par t lineup to tons -par t lineup to 2.0 tons 6-par t lineup to tons 7-par t lineup to 3.0 tons. When 1 m jib installed, actual load that can be lifted with main hook block should be reduced 0.3 ton from above chart. 6. The 1 m jib lifting load should be reduced (0.3ton+main hook block weight) from above chart. However do not exceed.8tons. 7. Bucket operation can not be perfomed by 1 m jib. 8. Maximum boom length is 18m on bucket work. 9. The rated lifting load is ton on bucket work. Do not exceed ton for "bucket weight + load" during bucket work. (Unit:metric ton).m x m x

12 al equipment Moment limiter(o verload prevention) Y ellow rotary light W ireless phone Bullhor n Comb ustion type heater Defroster Spar k arrester Dig ging depth/lift indicator (with ucket b opening angle indicator) Electrical type vel le indicator Le vel vail Fire xtinguisher e Monitor TV (wa tching rear, left and drum) Engine throttle pedal Dr um rotation roller Dr um mirror Ca twalk Large siz e tool box (installed on car body) T hird drum (with clutch and brake:type ) T hird drum (automatic brake:type B) R eeving winch Hy draulic power take off ( Spec.) 300kg/cm 2 x 22L/min Hy draulic power take off (B Spec.) 210kg/cm 2 x L/min nemometer Dr um light Work light on boom Work light for rear direction R ope guard for boom top surface 3m, 6m, 9m, inser t boom with pendant rope 6m basic jib boom 3m, 6m, jib inser t boom with pendant rope 1m jib 3ton hook lock b (3 sheaves) 2ton hook lock b (3 sheaves) 1ton hook lock b (1 sheaves).8ton hook lock b Fulcr um plate for raising of attachment (standard accessor y for longer than 39m boom) Cra wler frame fixing device to pontoon irconditioner Kishi-Tokai Bldg.,8-4-4, Nishikamata, Ota-ku, Tokyo , JPN Phone: Fax: , 8841 Specifications are subject to change without notice due to technical improvements or modifications. Distributed by Printed in Japan IK LL20