Schedule Start 25/08/201620:00. A/C P4-KDB A/C S/N 5404 A/C EFF 352 Skills NDT Corrosion Weight Balance. MPD Area Actual HRs:A h m;b1 h m;b2 h m;m h m

Transcription

1 DLY-A39/A0/A A/C P4-KDB A/C S/N 5404 A/C EFF 352 Skills Man/Hours NDT Corrosion Weight Balance MPD Area Actual HRs:A h m;b h m;b2 h m;m h m Material Part No Category Qty Unit BP297 MIL-PRF LUBRICANT OIL CONS QT SKYDROL LD-4 HYDRAULIC OIL CONS QT BP2380 TURBO-OIL CONS QT A/C Type and Series A/C A0/2 P4-KBC P4-KBA P4-KBB P4-KBD P4-KBE P4-KBF P4-KBG A/23 P4-KDB P4-KDA Nose Landing Gear General Visual Inspection of Nose Gear and Nose Gear Doors (EWIS) iaw AMM General Visual Inspection of the Nose Landing Gear iaw AMM Inspection/Check of the NLG Wheels and Tires iaw AMM Inspection/Check of the Tires Pressure iaw AMM Clean the exposed Sliding Portion of the NLG with Hydraulic Fluid 5606 iaw AMM Check placards and markings at this area. Refer IPC LH FWD Fuselage (from nose to wing) General Visual Inspection of Lower Half of Fuselage iaw AMM Zonal Inspection the as far as Visible from the Ground Upper Half of the Fuselage iaw AMM General Visual Inspection of hydraulic compartment and fairings (EWIS) iaw AMM Check placards and markings at this area. Refer IPC Non-Routine TC Raised Yes No NR TC Number : Page: of 7

2 DLY-A39/A0/A 3 LH Main Landing Gear General Visual Inspection of Main Landing Gear Main Doors (EWIS) iaw AMM General Visual Inspection of LH MLG-WELL and hydraulic compartment (EWIS) iaw AMM General Visual Inspection of the LH Main Landing Gear iaw AMM --00 Inspection/Check of the LH MLG Wheels and Tires iaw AMM Inspection/Check of the Tires Pressure iaw AMM Clean the exposed Sliding Portion of the LH MLG with Hydraulic Fluid 5606 iaw AMM --00 Functional Check of Brake Heat Pack for wear by use of the Wear indicator (Parking Brake Applied) iaw AMM Check placards and markings at this area. Refer IPC LH Engine Zonal Inspection of the LH Power Plant, the Nacelles and the Pylons iaw AMM General Visual Inspection of Engine Air Intake (externally), Fan and Accessory Gearbox iaw AMMs: Examine the LP Compressor Fan Blade Airfoils iaw AMM Note: if FOD found do Inspection of the Engine after Bird Strike, Foreign Object or Slush Ingestion iaw AMM Examine the Annulus Fillers iaw AMM Inspection of the Inlet Cone and the Inlet Cone Fairing iaw AMM Check of the IDG Oil Level and Filter Differential Pressure Indicator (DPI) iaw AMM ( related item) If oil level is not correct: - Perform IDG servicing AMM Make a record in TLB Box 6 "IDG Uplift" - Check the previous few pages of TLB for IDG oil uplift data to prevent excessive oil consumption. Check Leakage Rates at Drains Mast not exceeded limits iaw AMM General Visual Inspection of Trust Reverser (EWIS) (without opening thrust reverser halves) iaw AMM Check placards and markings at this area. Refer IPC : Page: 2 of 7

3 DLY-A39/A0/A 5 LH Wing Zonal Inspection of the LH Wing as far as visible from the ground iaw AMM Check static dischargers for presence. Check control surfaces for damage and evidence of fluid leakage Check fuel tanks for evidence of fuel leakage iaw AMM Check placards and markings at this area. Refer IPC LH AFT Fuselage (from wing to tail) General Visual Inspection of Lower Half of Fuselage iaw AMM Zonal Inspection as far as Visible from the Ground of the Upper Half of the Fuselage iaw AMM Check placards and markings at this area. Refer IPC Empennage Zonal Inspection as far as visible from the ground of the Stabilizers and the Cone/Rear Fuselage iaw AMM Check placards and markings at this area. Refer IPC , Carry out APU Oil quantity visual check and service to full ( related item) 8 RH AFT Fuselage (from tail to wing) General Visual Inspection of Lower Half of Fuselage iaw AMM Zonal Inspection as far as Visible from the Ground of the Upper Half of the Fuselage iaw AMM Check placards and markings at this area. Refer IPC AFT Cargo Compartment General Visual Inspection of AFT Cargo compartment (EWIS) iaw AMM Visual Check of Cargo Compartment Decompression, Lining, Floor Panels and Pressure Compensation Valve (as far as visible, if ACT(s) installed Visual Inspection of the Cargo Compartment and the Components of the Cargo Loading System iaw AMM Check placards and markings at this area. Refer IPC : Page: 3 of 7

4 DLY-A39/A0/A 0 RH Wing Zonal Inspection of the LH Wing as far as visible from the ground iaw AMM Check static dischargers for presence Check control surfaces for damage and evidence of fluid leakage Check fuel tanks for evidence of fuel leakage iaw AMM Check placards and markings at this area. Refer IPC RH Engine Zonal Inspection of the RH Power Plant, the Nacelles and the Pylons iaw AMM Engine Air Intake (externally), Fan and Accessory Gearbox - inspection/check iaw AMM Examine the LP Compressor fan blade airfoils iaw AMM Note: if FOD found do Inspection of the Engine after Bird Strike, Foreign Object or Slush Ingestion iaw AMM Examine the Annulus Fillers iaw AMM Inspection of the Inlet Cone and the Inlet Cone Fairing iaw AMM Сheck of the IDG Oil Level and Filter Differential Pressure Indicator (DPI) iaw AMM ( related item) If oil level is not correct: - Perform IDG servicing AMM Make a record in TLB Box 6 "IDG Uplift" - Check the previous few pages of TLB for IDG oil uplift data to prevent excessive oil consumption. Check Leakage Rates at Drains Mast not exceeded limits iaw AMM General Visual Inspection of Trust Reverser (EWIS) (without opening thrust reverser halves) iaw AMM Check placards and markings at this area. Refer IPC : Page: 4 of 7

5 DLY-A39/A0/A 2 RH Main Landing Gear General Visual Inspection of Main Landing Gear Main Doors (EWIS) iaw AMM General Visual Inspection of RH MLG-WELL and hydraulic compartment (EWIS) iaw AMM General Visual Inspection of the RH Main Landing Gear iaw AMM --00 Inspection/Check of the RH MLG Wheels and Tires iaw AMM nspection/check of the Tires Pressure iaw AMM Clean the exposed Sliding Portion of the RH MLG with Hydraulic Fluid 5606 iaw --00 Functional Check of Brake Heat Pack for wear by use of the Wear indicator (Parking BrakeApplied) ) iaw AMM Check placards and markings at this area. Refer IPC RH FWD Fuselage (from tat to nose) General Visual Inspection of Lower Half of Fuselage iaw AMM Zonal Inspection as far as Visible from the Ground of the Upper Half of the Fuselage iaw AMM Check placards and markings at this area. Refer IPC FWD Cargo Compartment General Visual Inspection of Forward Cargo Compartment (as far as visible, if ACT(S) installed) (EWIS) iaw AMM Visual Check of Cargo Compartment Decompression, Lining, Floor Panels and PressureCompensation Valve (as far as visible, if ACT(s) installed) iaw AMM ( related item) Visual Inspection of the Cargo Compartment and the Components of the Cargo Loading System iaw AMM Check placards and markings at this area. Refer IPC : Page: 5 of 7

6 DLY-A39/A0/A 5 Flight Deck Detailed Visual Inspection of All Cockpit Windows from Inside iaw AMM Cleaning of Cockpit Windows iaw AMM Print, Review the Post Flight Report for ECAM Warning Messages and Failure Messages iaw AMM Perform fault isolation action iaw TSM if necessary and attach PFR to AIRCRAFT TECHNICAL REPORT page. Print the APU MES/IDLE Report iaw AMM and attach to this task card Print APU Hours and Cycles iaw AMM and attach to this task card Inspection of Oxygen Pressure for the Flight Crew iaw AMM If pressure is not correct: - Fill the oxygen system - Make a record in TLB Box and 2 regarding of oxygen servicing - Check the previous few pages of TLB for oxygen servicing data to prevent excessive consumption. Engine Fire and Overheat Detection - Adjustment/Test iaw AMM ( related item) APU Fire and Overheat Detection - Adjustment/Test iaw AMM Operational Test of the Annunciator Lights iaw AMM Operation Test of Exterior Lights iaw AMMs , , , , , , Operational Test of the Emergency Lights Cabin Check Pressure of Emergency Cylinder/Accumulator of the Passenger/Crew Doors iaw AMMs: , Detailed Inspection of the Waste Compartment Including Waste Flap and Operational Check of Waste Flap iaw AMM Operational Test of the General Illumination iaw AMM Check Photoluminescent Strips of the Floor-Proximity Emergency-Escape Path-Marking for damages and cleanness and replace/clean as required iaw AMM : Page: 6 of 7

7 DLY-A39/A0/A 7 General Drain Water Content from Fuel Tanks iaw AMM ( related item) Inspect spare filament stowage. Replenish if necessary. Check availability of 3 spare rolls of paper for printer 4TW. Replenish if necessary. Check availability of spare Technical Log Book pages. Replenish if necessary Check ADD/CDD pages, status sheet and Notice to Engineers and Crew. Ensure remaining hours are sufficient for the planned program and that all deferred items due are auctioned as required. Certify accomplishment of Daily Check in Aircraft Technical Log Book. : Page: 7 of 7

8 TASK CARD CABIN CONDITION DLY CHECK 06 2 A/C P4-KDB A/C S/N 5404 A/C EFF 352 Skills Man/Hours NDT Corrosion Weight Balance MPD REV. Area Actual HRs:A h m;b h m;b2 h m;m h m A/C Type and Series A/C A39/ P4-YAS A0/2 P4-KBC P4-XAS P4-VAS P4-WAS P4-KBA P4-KBB P4-KBD P4-KBE P4-KBF P4- KBG A/23 P4-NAS P4-OAS P4-KDB P4-KDA CONSUMABLE MATERIALS. Strap (Tamper Shields P/N A-8-030) as required. TOOLS / EQUIPMENT N/A EXPENDABLES / PARTS N/A REFERENCES N/A 2 ACTION Note : All minor damage should be written in "Additional Item Worksheet" form # KC/ENG/034. Note 2: Replace all minor damage parts at first maintenance apportunety. Note 3: If structural damage was found, it must be repaired before the next flight or ADD should be opened. 3 Inspect the cabin condition as follows: a. Check all cabin closets and stowage compartments and doors for condition and security; b. Check all passenger overhead stowage for cleanliness; c. Check curtain rails for condition and security; d. Check curtains and tieback straps for cleanliness and condition; e. Check all carpets, flight deck, galleys and lavatories floor coverings for condition, cleanliness and correct attachment..2 Non-Routine TC Raised Yes No NR TC Number : Page: of 3

9 TASK CARD CABIN CONDITION DLY CHECK Inspect each lavatory compartment, as follows: CAUTION: BELOW INSPECTION IS RELATED TO AD ALL THE DEFECTS FOUND DURING THE INSPECTION REQUIRED BY ITEM 4 (B, С, D) MUST BE CORRECTED BEFORE THE FLIGHT. a. Check lavatories soap dispensers for condition and capability to work; b. Check lavatory waste bin flappers can close normally with spring pressure; c. Check lavatory waste bin flappers and compartment surrounding edges for condition to ensure there are no sharp edges; d. Check lavatory door & door locks for operation, condition and security; e. Check lavatory paper roll holder for condition. 5 Inspect each Business class seat, as follows: a. Check seat bottom, backrest and headrest cover for cleanliness; b. Check seat side arm, center console arm caps for condition; c. Check seat belt and buckle for condition and security. Pay particular attention that the seat belt buckles are mounted on the opposite side from the aisle for the seats located along the aisle; d. Check meal table, hinge and cocktail table for condition; e. Check headrest ear wing security and operation. f. Check all PCU for operation and condition. g. Check the IFE wiring underneath the seats to make sure they are not hanging down. 6 Inspect each Economy class seat, as follows: a. Check seat bottom, backrest and headrest covers for cleanliness; b. Check seat belt and buckle for condition and security. Pay particular attention that the seat belt buckles are mounted on the opposite side from the aisle for the seats located along the aisle; c. Check the meal table lock does not cause an obstruction on the seats adjacent to over wing emergency exits. d. Check the IFE wiring underneath the seats to make sure they are not hanging down. 7 Inspect each flashlight, as follows: a. Check all flashlights for condition, correct installation and security; Note: make sure that strap P/N A is installed and not broken. : Page: 2 of 3

10 TASK CARD CABIN CONDITION DLY CHECK Inspect each cabin attendant seat, as follows: a. Check the retract mechanism (jump seat mechanism) returns the flight attendant seats to an upright position; b. Check the spring of retract mechanism for condition on the flight attendant seats. : Page: 3 of 3

11 TASK CARD AIRCRAFT PRERELEASE CHECK GENERAL VERIFICATION AFTER COMPLETION OF ALL MAINTENANCE - PRERELEASE CHECK ORIGINAL AIRCRAFT PRERELEASE CHECK 3 A/C P4-KDB A/C S/N 5404 A/C EFF 352 Skills Man/Hours NDT Corrosion Weight Balance MPD Area Actual HRs:A h m;b h m;b2 h m;m h m.0 A/C Type and Series A/C A39/ P4-YAS A0/2 P4-KBC P4-XAS P4-VAS P4-WAS P4-KBA P4-KBB P4-KBD P4-KBE P4-KBF P4- KBG A/23 P4-NAS P4-OAS P4-KDB P4-KDA B757/200 P4-EAS P4-FAS P4-GAS P4-MAS P4-KCU B767/300ER E90/00LR P4-KCA P4-KCB P4-KEB P4-KEC P4-KEA P4-KCC P4-KCD P4-KCI P4-KCE P4-KCF P4-KCG P4-KCH P4-KCJ P4-KCK AFTER COMPLETION OF ALL MAINTENANCE ENSURE THAT: ALL TOOLS, SAFETY BOXES / DEVICES AND RIGGING PINS HAD BEEN RETURNED TO THE TOOL BOX AND CHECKED I.A.W. REGISTER. THE TOOL BOX IS RETURNED TO STORE AND ACCEPTED BY COUNTERSIGNATURE OF STORE STAFF MEMBER, IF NO LONGER REQUIRED. AIRCRAFT IS CLEAR OF ANY OTHER EXTRANEOUS PARTS AND MATERIALS. ALL DOORS, HATCHES AND PANELS ARE CLOSED AND SECURED. ALL STAIRS, PLATFORMS AND GROUND SUPPORT EQUIPMENT ARE MOVED AWAY FROM AIRCRAFT. Non-Routine TC Raised Yes No NR TC Number : Page: of

12 Control Sheet Print Date: 25/08/206 6:06 Page: of /Completion Date 25/08/206 25/08/206 A/C P4-KDB A/C S/N 5404 AIRCRAFT MAINTENANCE PROGRAM KC/AMP/04 REVISION 4 03/30/206 Priority Signature Stamp MND CABIN CONDITION DLY CHECK 2 AIRCRAFT PRERELEAS E CHECK MND GENERAL VERIFICATION AFTER COMPLETION OF ALL MAINTENANCE - PRERELEASE CHECK 3 All task cards on this Control Sheet have been completed or deferred and the Work Order number has been entered into the aircraft Technical Log Book Surname: Signature: Stamp: Date: Time UTC: ORIGINAL