KPS LPG Pipe System. Making fuel flow safely.

Transcription

1 KPS LPG Pipe System Making fuel flow safely

2 For retailers Long life expectancy The KPS LPG pipe is made of non-corroding polyethylene that has been used for petrol, gas and water piping for more than 60 years. Polyethylene has properties that make it superior for use in buried piping: It does not corrode in contact with water, nor will the material become degraded in contact with soil. Polyethylene piping can remain in service for decades. The KPS LPG pipe has an inner lining that prevents permeation of hydrocarbons to the environment. The liner is the same that is used in petrol piping, with proven zero permeation as a result. The end fittings that connect the pipes to the tank and dispensers are made from 100% stainless steel in order to provide long-term safety against corrosion and prevent hazardous gas leaks. Short payback time An investment in KPS plastic LPG piping pays off quickly compared to standard LPG steel piping. With KPS LPG piping you do not need to install cathodic protection for the piping and there is no need to close the site every few years to inspect for possible corrosion or to perform hyrdostatic pressure tests to verify integrity of the piping. Even for a small station, payback time will be reached in about 5 years. Polyethylene Safe in hazardous areas When switching from steel piping to plastic piping you need to take caution not to introduce static electricity hazards on your LPG station. KPS LPG pipes have a dissipative (conductive) lining that prevents electrostatical charging. KPS LPG piping is the only plastic LPG piping that can be grounded to earth and it offers inherent protection against electrostatical hazards. Conductive lining Permeation barrier

3 For project managers and architects Design support OPW can provide designers and architects with support already from the initial stages of a project. We can provide the specifications and drawings that you need for your project. We can even make detailed, station specific installation drawings ready to use for the building permit application - or provide customized training for project managers, designers and architects. Proven installation process The KPS LPG installation manual and installer training describes, step by step, the installation of KPS LPG piping. The complete process is verified at actual installations by our technical support team to make sure no construction delays occur. The KPS installation manual can be used by project managers during the planning stages as well as during installation and commissioning to verify that the installation work is performed correctly. Clear test & verification process KPS LPG Pipe System has a clearly defined test and verification process that shows the steps to take before the piping system is ready for commissioning. The LPG installation checklist and test documentation form can be used to verify that all recommended tests have been run successfully.

4 For installers Easy installation KPS LPG piping is considerably easier to install than stainless steel piping or plastic covered steel piping. The pipe is rolled out in full length from tank to dispenser. There is no need for welding or x-ray of welds. No cathodic protection is necessary as the pipe is non-corroding. Retain full flexibility on site KPS LPG pipe is delivered in coils of standard lengths. The installer can decide the correct pipe length on site and full flexibility is retained in order to adapt to unforseen circumstances that affect the run of the pipe, like large rocks or old concrete structures hidden in the ground. As there is no need to pre-order specific lengths, delivery times are shorter. Install using standard mechanical tools KPS LPG end fittings are installed using inexpensive standard tools. There is no need to rent or buy expensive machinery, or to order premounted fittings with extended delivery times as a result. We can provide complete tool kits with exactly the tools that are needed for installation, but you can just as easily buy them in your local hardware shop. Full technical support OPW provides full technical support for the KPS LPG Pipe System, starting with an easy to read installation manual, illustrated installation instructions and installer training in the local language. To get you off to a good start, we provide on-site installation support during your first KPS LPG piping installation. Our technical support is always available by phone or .

5 For retailers Rated for high pressures The KPS LPG Pipe System is rated for 25 bar (363 psi) continuous pressure, well above the pressures normally used on LPG filling stations. The pipe can be pressure tested at 40 bar (580 psi) to verify the integrity of the pipe after installation. The burst pressure or the pipe is around 250 bar, offering an excellent safety margin. TÜV approved KPS LPG Pipe System is approved by TÜV Süd for use on LPG filling stations. The TÜV approval validates that the KPS LPG Pipe System is fit for purpose and may be installed on LPG filling stations. TÜV Süd has concluded the KPS LPG piping will have a service life of at least 25 years. KPS LPG piping is the only plastic LPG pipe approved by TÜV. ATEX approved and EN compliant KPS LPG Pipe System is approved to the EU Directive 97/23/EC on workers safety and CE approved to the Pressure Equipment Directive (PED) and allowed to carry the CE mark. KPS LPG Piping System is also compliant with the relevant requirements in EN , Non-electrical equipment for potentially explosive atmospheres. When using KPS LPG piping you comply with all the mandatory EU directives for LPG filling stations. Solid supplier The KPS LPG pipe is developed by KPS, the leading developer, manufacturer and supplier of plastic piping for petrol, diesel and ethanol filling stations, with a track record going back to KPS petrol piping has successfully been installed at countless filling stations in Europe, Asia, Africa and the Middle East. KPS is now part of OPW, a global supplier of fuel retail equipment and a Dover company (NYSE: DOV). We are certified to ISO 9001 and

6 Operations in Europe, Middle East and Africa OPW EMEA Headquarters OPW Nordic OPW Sweden AB Box Kungsör Sweden Fibrelite Composites Ltd Snaygill Industrial Estate Keighley Road, Skipton North Yorkshire BD23 2QR UK Tel: OPW Ibéria Avda. Diagonal Plaza 14 Nave 41, Polígono Industrial Plaza ES Zaragoza Spain OPW Slovakia Antolská 4 SK Bratislava Slovakia OPW Czech Republic 4 6 Dover CR spol. s.r.o. Prumyslova Klasterec nad Ohri Czech Republic OPW France 73 avenue Carnot FR Cachan France OPW CIS Chistoprudniy boulevard, 17 bld.1, 8 floor Moscow, Russia OPW FMS Poland Petro Vend sp. z o.o. ul. Warszawska Węgrzce Poland OPW Retail Fueling Components and products to protect the environment and the consumer at retail fueling sites for conventional and alternative fuels. OPW Electronic Systems Innovative electronic tank gauges and fuel control systems to ensure customers know how much fuel they have and where it is going. Also, Automated Vehicle Wash Systems. OPW Chemical & Industrial Safe and efficient loading and unloading of critical hazardous chemicals: loading arms, swivel joints, sight flow indicators, quick and dry disconnect couplers, and safety breakaways. OPW Transportation Components and systems for use on Tank Trucks and Rail Tank Cars to ensure the safe handling, loading, transport and unloading of hazardous bulk products, including: petroleum, chemical and dry bulk cargo. NOTE: All information subject to engineering and/or other changes. All trade names are copyrighted. Patents Pending OPW Fueling Components Delaware Capital EMEA 09/2015 Formation, Inc. All Rights Reserved. DOVER and the DOVER logo are registered trademarks of Delaware Capital Formation, Inc., a wholly-owned subsidiary of Dover Corporation.