Troubleshooting and Maintenance of Air-Powered Pumping Systems

Size: px

Start display at page:

Download "Troubleshooting and Maintenance of Air-Powered Pumping Systems"

Imogen Deirdre Osborne
5 years ago
Views:

Troubleshooting and Maintenance of Air-Powered Pumping Systems David Kaminski QED Environmental Systems Inc. Ann Arbor, MI / San Leandro, CA Copyright QED Environmental Systems, Inc.

1 Troubleshooting and Maintenance of Air-Powered Pumping Systems David Kaminski QED Environmental Systems Inc. Ann Arbor, MI / San Leandro, CA Copyright QED Environmental Systems, Inc. 2015; all rights reserved. The information contained within this document may not be published, broadcast, rewritten or otherwise distributed without prior written authorization from QED. Today s Webinar Topics Air-powered pump system components Principles of operation how it works Diagnosing the problem: Look and Listen Common operational issues Safety considerations during pump maintenance Tips on pump removal and installation Pump disassembly tools and tips Cleaning frequency and service life expectations Spare parts and spare pumps save time and $$$ Accessories for improving pump performance 1

2 QED AutoPump AP4+ Pump Components Discharge Head & Air Valve Assemblies Discharge Tube/Float Guide Pump Body (Casing)

works Discharge Cycle When float reaches the top of its travel, exhaust valve closes and air inlet valve opens Air

follows and pulls actuator rod down, closing the air inlet valve and opening exhaust valve to repeat Fill Cycle Fill

2 2 QED AutoPump AP4+ Pump Components Discharge Head & Air Valve Assemblies Discharge Tube/Float Guide Pump Body (Casing) Float Assembly with Guide Plates Actuator Rod Inlet Valve Assembly and Inlet Screen Air-powered automatic pump: How it works Discharge Cycle When float reaches the top of its travel, exhaust valve closes and air inlet valve opens Air pressure against liquid closes inlet check valve and pushes liquid up discharge tube As liquid level drops, float follows and pulls actuator rod down, closing the air inlet valve and opening exhaust valve to repeat Fill Cycle Fill Cycle Hydrostatic pressure opens inlet check valve As pump fills with liquid, air escapes through exhaust valve and internal float rises

3 Normal Pump Operating Characteristics 1. Cycling you should hear a release of air pressure when the pump is cycling (exhaust cycle). 2. Pressure gauge if there is a filter/regulator at the well head, you can see a slight drop in the air pressure (5-10 PSI) with each pump discharge cycle 3. Cycle counter the cycle counter should advance a half count in the discharge cycle, then advance a full count with an audible click during the exhaust cycle What if my pump isn t cycling? Determine if the issue is the operating conditions in the well or a pump malfunction Examples of operating conditions: Very low well yield (will eventually cycle check counter) Liquid level has dropped below actuation point Air supply pressure insufficient for discharge Excessive discharge line back pressure Examples of pump malfunction Float sticking due to solids buildup, slime, silt Check valve not working due to debris, sand Air valve mechanism plugged or out of adjustment 3

coming from the pump exhaust line (may be above or below well cap) and/or the liquid discharge line Pump stuck in discharge mode Continuous air from the exhaust line can indicate that the

4 First Step: Look and Listen Look at the well head and connections for an obvious problem broken fittings or loose connections, tubing kinks, etc. Listen for an air leak from a fitting or line at the well head Look at the air pressure gauge for low or no pressure Listen for a continuous discharge condition you ll hear a hissing sound coming from the pump exhaust line (may be above or below well cap) and/or the liquid discharge line Pump stuck in discharge mode Continuous air from the exhaust line can indicate that the pump is stuck in discharge mode or in crossover between pump cycles The float may be stuck due to buildup on the discharge tube or debris inside the pump Cleaning will usually resolve the problem, but may require air valve adjustment 4

Pump stuck between cycles If the pump is stuck between cycles, both the air inlet and exhaust poppet valve will be open, allowing air to pass continuously out of the exhaust port and possibly through

5 Pump stuck between cycles If the pump is stuck between cycles, both the air inlet and exhaust poppet valve will be open, allowing air to pass continuously out of the exhaust port and possibly through the discharge line Additional evidence: the cycle counter may be stuck between cycle counts Possible causes include an air valve mechanism that is worn or out of adjustment, a worn pivot pin or worn air valve lever half bushing Cleaning, adjustment or repair may be required to resolve the problem Is liquid level above actuation point? To determine if you have sufficient liquid over the pump to actuate the air valve, you need to know: The installed depth of the pump The pump model and its actuation point The liquid level in the well/riser If the liquid level is above the actuation point and there is sufficient air pressure but the pump isn t cycling, there may be a problem with the pump, such as a stuck float, debris, actuator rod hang-up, air valve issue, etc. 5

6 Pump Actuation Point The point at which the liquid level inside the pump activates the air valve mechanism is called the actuation point The actuation point is the distance from the bottom of the

position in the well determines the maximum drawdown level in the well How vacuum affects the pump actuation point A vacuum applied to the well (e.g.

6 6 Pump Actuation Point The point at which the liquid level inside the pump activates the air valve mechanism is called the actuation point The actuation point is the distance from the bottom of the pump to the top of the float travel (top of inlet on top-fill pumps) This distance varies based on pump body length, float length and inlet position and is specified for each pump model The pump position in the well determines the maximum drawdown level in the well How vacuum affects the pump actuation point A vacuum applied to the well (e.g., landfill gas collection, vapor extraction) will RAISE the actuation point above the design point when the pump exhaust is outside the well The increase in the actuation point is based on the amount of vacuum applied to the well, measured in inches (centimeters) of water column (WC) In the example, a vacuum of 20 (51 cm) WC raises the actuation point of the pump from 33 (84 cm) to 53 (135 cm)

How to check if vacuum is preventing the pump from cycling 1. Install a level tape in the well or activate your dedicated level measurement system 2.

7 How to check if vacuum is preventing the pump from cycling 1. Install a level tape in the well or activate your dedicated level measurement system 2. Turn off and release vacuum at the well cap/flange 3. Measure/watch the liquid level and wait for it to begin dropping 4. If the pump starts cycling at the design actuation point, the problem is insufficient submergence under vacuum. Possible solutions: Lower the pump in the well/riser if possible Use a shorter pump model with a lower actuation point If air exhaust is outside the well, change to inside well or install an equalization valve to reference exhaust to vacuum Pump not cycling - insufficient air pressure at the well head A pump may not cycle if the air pressure is too low to lift the liquid to the well head and/or overcome header line back pressure Air-powered pumps need a minimum of 0.5 PSI air pressure for every foot of lift desired plus 1.0 PSI for every PSI of back pressure in the header line Test for low air pressure: increase pressure at well head in 5 PSI increments; pump will start cycling if pressure was too low to overcome lift requirement Test for high header line back pressure: turn off air, disconnect discharge line at header and direct it back into well; pump will start cycling if pressure was too low to overcome header back pressure 7

How to jump start your pump Sometimes a quick jump start can get the pump cycling again when it stalls or is stuck in discharge Remove the air line from the filter/regulator, allow all the air to

jump start method gets the pump cycling again, it s a good indication that the pump needs to be cleaned, serviced or adjusted to maintain consistent operation and maximum performance Air Valve

8 How to jump start your pump Sometimes a quick jump start can get the pump cycling again when it stalls or is stuck in discharge Remove the air line from the filter/regulator, allow all the air to exhaust from the pump, then reconnect the air line; pump should cycle if sufficiently submerged Another jump start is to unbolt the well cap and shake the pump/tubing to dislodge the float If the jump start method gets the pump cycling again, it s a good indication that the pump needs to be cleaned, serviced or adjusted to maintain consistent operation and maximum performance Air Valve Mechanism Adjustment The air valve mechanism should not require adjustment unless it has been repaired or has some wear from long-term use If adjustment is necessary, contact QED for information and instructions based on pump model Air Valve Out of Adjustment (Gap between valve mechanism and pump head) After Proper Air Valve Adjustment 8

Pump maintenance safety considerations Most important make sure the pump and all lines are not pressurized

Wear appropriate safety gear Safety glasses with side shields or a full face shield Protective outer clothing

vest or coat Hard hat Shut-offs, check valves and lines Shut off any valves air supply, discharge header

9 Pump maintenance safety considerations Most important make sure the pump and all lines are not pressurized before you begin any disassembly! Wear appropriate safety gear Safety glasses with side shields or a full face shield Protective outer clothing (e.g. Tyvek jump suit) Chemically resistant gloves taped at top to prevent leaks Reflective high-visibility vest or coat Hard hat Shut-offs, check valves and lines Shut off any valves air supply, discharge header Release all the air pressure from the pump If the pump discharge tubing is filled with liquid, you can lighten your load using the QED Pump Blow-Out Kit (Part Number shown here) to empty the lines 9

Lifting the pump and tubing Wear protective gloves and get a good grip on the tubing or hoses Try to

winch or crane Well head tubing rollers If possible, use a well head tubing roller mounted to the

10 Lifting the pump and tubing Wear protective gloves and get a good grip on the tubing or hoses Try to avoid getting kinks in tubing kinks tend to be permanent and can restrict flow or create leaks Use your legs, NOT YOUR BACK! Use a step ladder or tailgate to gain some height and leverage If the system is too heavy, use a winch or crane Well head tubing rollers If possible, use a well head tubing roller mounted to the edge of the well casing or flange to simplify pump removal and avoid tubing kinks Pull the tubing into the roller and walk it out of the well less stress on legs, back and shoulders 10

Well head tubing rollers Tubing roller mounted on flange

air lines Debris in air lines (dirt, insects, etc.

poppets Blow out air header lines before connecting pump

11 Well head tubing rollers Tubing roller mounted on flange Tubing roller mounted on well casing Keeping debris out of air lines Debris in air lines (dirt, insects, etc.) can clog filter regulators and plug pump air valve poppets Blow out air header lines before connecting pump air supply hoses Cap or tape end of tubing after pulling the pump to avoid debris 11

Cleaning air-powered pumps Determining cleaning

site-by-site basis - some sites may go a year or

cleaning as often as monthly or more where high

history, pull new pumps after 1-3 months of use

of stalling Planned maintenance can be more cost

12 Cleaning air-powered pumps Determining cleaning frequency Cleaning frequency is determined on a site-by-site basis - some sites may go a year or more without cleaning while others may require cleaning as often as monthly or more where high solids or sticky deposits occur If no site history, pull new pumps after 1-3 months of use to gauge need for cleaning or wait for indication of stalling Planned maintenance can be more cost effective than responding to pumps that shut down when dirty 12

13 AutoPump *AP4+ Designed for easier cleaning Easier disassembly: removing four bolts on bottom inlet allows

quick-release clip on actuator rod allows quick float removal for easier cleaning.

Increased durability: All metal parts are 304SS or higher for improved corrosion resistance; plastic parts are

pro-rating in later years * Patent Pending AutoPump AP4+ Design Features New Air Valve Mechanism Design The new

13 13 AutoPump *AP4+ Designed for easier cleaning Easier disassembly: removing four bolts on bottom inlet allows complete pump disassembly in minutes no turning of the inlet assembly or O-ring hang-up/dragging Easier service: quick-release clip on actuator rod allows quick float removal for easier cleaning. Pump body has a high-polish ID finish to reduce solids build-up and precision bore sizing to improve O-ring fit Increased durability: All metal parts are 304SS or higher for improved corrosion resistance; plastic parts are high-strength & hightemperature engineering plastics (PVDF, PEEK) Increased warranty: 5-year full warranty with no pro-rating in later years * Patent Pending AutoPump AP4+ Design Features New Air Valve Mechanism Design The new captured pin design eliminates need for fasteners, clips or cotter pins at valve stem Improved reliability, easier to service exhaust seat is easier to adjust Now on all AP4+ models!

14 Introducing the first low-maintenance air-powered pump: The

requires 50% less time to clean The Ultra combines all of the

innovative design that reduces build-up of solids and sticky

challenging applications Fewer pump pulls for maintenance

electro-polished center rod reduce solids buildup, low-friction

parts are 316-grade SS for greater corrosion resistance and

14 14 Introducing the first low-maintenance air-powered pump: The Ultra lasts up to 10 times longer between service events and requires 50% less time to clean The Ultra combines all of the design features and rugged reliability of the AutoPump AP4+ in an innovative design that reduces build-up of solids and sticky deposits on the float and center rod Greater reliability in challenging applications Fewer pump pulls for maintenance Cleaning is faster and easier Design Features Non-stick float and electro-polished center rod reduce solids buildup, low-friction engineered plastic guide plates reduce pump stalling All metallic parts are 316-grade SS for greater corrosion resistance and reliability Non-stick, high polish finishes make cleaning easier can be as easy as wipe and rinse

15 Field testers compared the new AutoPump Ultra to existing pumps and reported the following results: Maximum uptime Minimum Downtime Teardown and cleaning took absolutely no effort No soaking

15 15 Field testers compared the new AutoPump Ultra to existing pumps and reported the following results: Maximum uptime Minimum Downtime Teardown and cleaning took absolutely no effort No soaking required Only needed a water spray to clean Removed residue with some clean water and the swipe of a hand Easier to clean by 50% It s been running for four months and I haven t had to clean it yet! Annual Pump Cleaning Savings with AutoPump Ultra Standard Pump AutoPump Ultra Cleaning Frequency Pump Pulls/Year AP Ultra Frequency Pump Pulls/Year Annual Pulls Saved $50/pull $100/pull $150/pull 4 weeks weeks < 3 10 $ 500 $ 1,000 $ 1,500 1 week weeks < 3 17 $ 850 $ 1,700 $ 2,550 2 weeks 26 8 weeks < 7 19 $ 950 $ 1,900 $ 2,850 2 weeks weeks < 3 23 $ 1,150 $ 2,300 $ 3,450 1 week weeks < 3 49 $ 2,450 $ 4,900 $ 7,350 Reducing cleaning frequency with the AutoPump Ultra by as little as 50% at an average cleaning frequency of every 4 weeks can save from $325 to $975 on an annual basis!

Getting the right tools QED offers a complete tool kit for AP4 pumps Double pin spanner to remove threaded inlet Honing tool to remove hard deposits from pump body Casing removal tool, punch and

16 Getting the right tools QED offers a complete tool kit for AP4 pumps Double pin spanner to remove threaded inlet Honing tool to remove hard deposits from pump body Casing removal tool, punch and Allen wrench Optional pipe vise with rubber jaws to hold pump body What about tools for the AP4 Plus? The newly redesigned AP4+ has a bottom inlet design that comes off easily by removing three small bolts no need for the spanner or casing tool! The honing tool and pipe vise (if desired) can be purchased separately AP4 Service Tool Kit with optional Pipe Vise 16

Cleaning agents and supplies Degreasing agents such as Simple Green or Detergent 8 can remove

parts Use brush kits with extended handle to clean inside the pump body and discharge tube

acid and vinegar (acetic acid) can help remove heavy mineral deposits and biorock avoid

Don t clean acetal (Delrin ) plastic parts with acids it can weaken/damage them NEVER mix acids

17 Cleaning agents and supplies Degreasing agents such as Simple Green or Detergent 8 can remove oily or slimy deposits Scouring pads can remove about 90% of bio-growth and buildup on pump parts Use brush kits with extended handle to clean inside the pump body and discharge tube Cleaning agents for scale buildup Cleaning solutions such as CLR or common acids such as citric acid and vinegar (acetic acid) can help remove heavy mineral deposits and biorock avoid hydrochloric or sulfuric acids Do not leave metal parts in strong acids overnight! Don t clean acetal (Delrin ) plastic parts with acids it can weaken/damage them NEVER mix acids with other cleaning solutions ALWAYS rinse other cleaners away first to avoid dangerous (and potentially fatal) chemical fumes 17

18 Spare parts for field repairs Spare parts needed will vary by pump model, but most require only a handful of parts The quantity of spare parts you will need is dependent on the size of your site and how many pumps you have QED Customer Service can help you with recommended parts for your pumps, such as check balls, O-rings, fittings and springs Spare pumps = major cost savings When field labor for cleaning or repairs exceeds minutes, having one or more spare pumps can save considerable cost over immediate field repair Less downtime, especially valuable in LFG wells Maintenance can be done in the shop or by the manufacturer rather than under field conditions No need to stock every necessary spare parts Shipping for parts or pump repairs can be done at economy rates rather than overnight shipping 18

19 Accessories to improve performance and reduce maintenance in tough applications Silt and Foam Filter Designed to reduce solids loading in

material can be cleaned or replaced Can also improve pump performance and reduce leachate emitting from external exhaust line in wells with

in wells with silt or where solids deposit on pump components Actuator rod slot is wider for greater clearance between rod and float Now

19 19 Accessories to improve performance and reduce maintenance in tough applications Silt and Foam Filter Designed to reduce solids loading in pumps to improve performance and extend maintenance intervals Threads into pump inlet assembly (replaces standard inlet screen) Filter pad material can be cleaned or replaced Can also improve pump performance and reduce leachate emitting from external exhaust line in wells with foaming leachate Accessories to improve performance and reduce maintenance in tough applications Wide Slotted Float Can improve performance in wells with silt or where solids deposit on pump components Actuator rod slot is wider for greater clearance between rod and float Now standard on AP4+ and AP Ultra models Can be retrofit to existing AP4+ pumps (contact QED Customer Service for details) Standard Float Wide Slot Float

Accessories to improve performance and reduce maintenance in tough applications Wide-Slot Float with Non-Stick Coating Entire float assembly is coated with a proprietary non-stick coating Greatly

with sticky deposits or high dissolved solids Can be retrofit to existing AP4+ pumps contact QED for details Stand tubes for pump testing A stand tube should be used to verify that a pump is working

20 Accessories to improve performance and reduce maintenance in tough applications Wide-Slot Float with Non-Stick Coating Entire float assembly is coated with a proprietary non-stick coating Greatly reduces build-up of solids on the float, which can extend maintenance intervals Speeds cleaning and reduces chance of damaging float during cleaning Replaces Teflon-wrapped floats for applications with sticky deposits or high dissolved solids Can be retrofit to existing AP4+ pumps contact QED for details Stand tubes for pump testing A stand tube should be used to verify that a pump is working before you send it back down the well to avoid pulling it again if it s still not working You can make a stand tube from a piece of 4-inch diameter PVC pipe or well casing about 5 feet long, with a flat threaded cap or plug at the bottom PVC is very inexpensive, holds up well to most cleaning solutions and leachates A stand tube can save HOURS of lost time if you find that a pump isn t working properly before it s installed 20

Many QED pumps have been in use for 12-15 years and are still operational due to regular maintenance 90% of all pump maintenance is cleaning, not repairs We are confident that the new AutoPump

21 Pump service life expectations Pump service life is dependent on operating conditions of each well (chemistry, temperature, solids, etc.) and proper materials selection for the application The biggest factor you can control is pump maintenance. Many QED pumps have been in use for years and are still operational due to regular maintenance 90% of all pump maintenance is cleaning, not repairs We are confident that the new AutoPump Ultra 4.0 will prove to be a winner at your site QED will send you a new Ultra pump for evaluation in your most challenging well or sump After trial period, QED will invoice you for the pump, or just return it with no obligation to buy Contact QED at or Info@qedenv.com for more information on the Try & Buy program 21

application seen at landfill and remediation sites with longer service life than other pump designs. Questions?

22 22 Some applications are a bit more challenging than others, but with proper selection of pump model and materials, good installation practices and adequate preventative maintenance, air-powered automatic pumps can handle some of the toughest pumping application seen at landfill and remediation sites with longer service life than other pump designs. Questions? David Kaminski QED Environmental Systems, Inc. info@qedenv.com Toll-Free Numbers Ann Arbor, MI: San Leandro, CA: Website

Troubleshooting and Maintenance of Air-Powered Pumping Systems

Troubleshooting and Maintenance of Air-Powered Pumping Systems David Kaminski QED Environmental Systems Inc. Ann Arbor, MI / San Leandro, CA Copyright QED Environmental Systems, Inc. 2013-2017; all rights