英文使用手冊 MS 印製

Transcription

1 英文使用手冊 MS 印製

2 MS337 Hand Held Scanner User's Manual

3

4 TABLE OF CONTENTS Scanner Operation... 1 Presentation and Trigger Modes... 1 In-Stand... 1 Out-of-Stand... 2 Omnidirectional and/or Linear Scanner Modes... 3 Aiming and Illumination... 5 Data Output... 6 Character Suppression... 7 Character Suppression... 8 Same Symbol Timeouts... 9 Code Types and Decode Rules UPC/EAN Code Code of 5 Codes Codabar Code Code Telepen Plessey Codes Additional Decode Features Configurable Code Lengths Data Matrix QR Code MaxiCode Aztec Postal Codablock Options PDF Options Interfaces Prefixes/Suffixes User Configurable Prefixes, All Data Standard Prefix Characters Longitudinal Redundancy Check Block Check Character Character Replacements User Configurable Suffixes, All Data i

5 Special Formats Code Formatting UPC/EAN Formatting Codabar Formatting Code 39 Formatting Code 11 Formatting Telepen Plessey of 5 Code Formatting ISBT Code 128 Implementation Configuration Mode Bar Codes Supplements USB Code Bytes Usage Code Bytes Reserved Codes Code Type Table ASCII Reference Table ASCII Reference Table Extended Key Code Reference Table Enter/Exit Configuration Mode Bar Code RSS Bar Code Implementation RSS Limited Bar Codes RSS Expanded Bar Codes Bar Code Configuration Methods UPC-A UPC-E Code UPC-E EAN-13/JAN Bookland EAN EAN-8/JAN Code UCC/EAN ii

6 ISBT Convert UPC-E to UPC-A Convert UPC-E1 to UPC-A Convert Code 39 to Code Convert I 2 of 5 to EAN Trioptic Code Discrete 2 of Codabar MSI Postal Code Symbologies Composite Symbologies D Symbologies Sample Bar Codes iii

7 iv

8 Presentation and Trigger Modes SCANNER OPERATION There are four configurable modes for scanning: the presentation mode, the multi-try trigger mode, the continuous trigger mode, and the single-trigger mode. These modes can be configured separately for in-stand and out-of-stand scanner operation. In-Stand * Presentation Mode In-Stand Multi-Try Trigger Mode In-Stand ³ ³ Continuous Trigger Mode In-Stand Single Trigger Mode In-Stand ³ ³ * Factory Default Configuration 1

9 Presentation and Trigger Modes Out-of-Stand SCANNER OPERATION Presentation Mode Out-of-Stand * Multi-Try Trigger Mode Out-of-Stand ³ ³ Continuous Trigger Mode Out-of-Stand Single Trigger Mode Out-of-Stand ³ ³ In-Stand/Out-of-Stand Mode Match Set In-Stand Mode to Match Out-of-Stand Mode ³ * Factory Default Configuration for the MS1690, MS1890 and the MS1633 Factory Default Configuration for the IS1650 2

10 SCANNER OPERATION Omnidirectional and/or Linear Scanner Modes The unit can be configured to operate as an omnidirectional scanner, or a linear scanner, or a combination of both. Trigger and presentation operations can be configured separately for Omnidirectional and Linear scan modes. When configured to operate as an omnidirectional scanner, all 1D and 2D barcodes are scanned omnidirectionally (except Code 128 scanner configuration labels, which have to be linearly aligned for successful scanning). When configured to operate as a linear scanner, the 1D barcodes have to be linearly aligned for successful scanning while the 2D barcodes cannot be scanned. When configured to operate as both the linear and omnidirectional scanner, the 1D barcodes have to be linearly aligned for successful scanning while the 2D barcodes are scanned omnidirectionally. By default, the scanner is configured to omnidirectional scanning for trigger and presentation operations. Enable Linear Only in Trigger Operations Disable Linear Only in Trigger Operations ³ ³ Enable 1D Linear Only in Trigger Operations Disable 1D Linear Only in Trigger Operations ³ ³ * Factory Default Configuration 3

11 SCANNER OPERATION Omnidirectional and/or Linear Scanner Modes Enable Linear Only in Presentation Operations Disable Linear Only in Presentation Operations ³ ³ Enable 1D Linear Only in Presentation Operations Disable 1D Linear Only in Presentation Operations ³ ³ * Factory Default Configuration 4

12 Aiming and Illumination SCANNER OPERATION Trigger and presentation operations can be configured separately to use the unit s linear illumination as an aiming instrument. * Enable Aiming in Trigger Operations Disable Aiming in Trigger Operations ³ ³ * Enable Aiming in Presentation Operations Disable Aiming in Presentation Operations ³ ³ * Enable Auto Illumination Disable Auto Illumination ³ ³ * Factory Default Configuration 5

13 Aiming and Illumination SCANNER OPERATION * Enable Auto Gain Disable Auto Gain ³ ³ Data Output * Enable Data Output Disable Data Output ³ ³ * Factory Default Configuration 6

14 SCANNER OPERATION Character Suppression Enable the Suppression of 1 Character * Disable the Suppression of 1 Character ³ ³ To suppress 1 character: 1. Scan the Enter/Exit Configuration Mode bar code, on page Scan the Enable the Suppression of 1 Character bar code. 3. Scan the Character 1 bar code (below left). 4. Scan the three code bytes that represent the character to be suppressed, on page Scan the Enter/Exit Configuration Mode bar code, on page 69. Enable the Suppression of 2 Characters * Disable the Suppression of 2 Characters ³ ³ To suppress 2 characters: 1. Scan the Enter/Exit Configuration Mode bar code, on page Scan the Enable the Suppression of 2 Character bar code above. 3. Scan the Character 1 bar code (below left). 4. Scan the three code bytes, on page 8, that represent the 1 st character to be suppressed. 5. Scan the Character 2 bar code (below right). 6. Scan the three code bytes, on page 8, that represent the 2 nd character to be suppressed. 7. Scan the Enter/Exit Configuration Mode bar code, on page 66. Character 1 Character 2 ³ ³ * Factory Default Configuration 7

15 Character Suppression (Code Bytes 0 9) ³ 0 SCANNER OPERATION Code Byte 0 ³ 1 Code Byte 1 ³ 2 Code Byte 2 ³ 3 Code Byte 3 ³ 4 Code Byte 4 ³ 5 Code Byte 5 ³ 6 Code Byte 6 ³ 7 Code Byte 7 ³ 8 Code Byte 8 ³ 9 Code Byte 9 8

16 Same Symbol Timeouts SCANNER OPERATION Retain Same Symbol Timeout on Trigger * Reset Same Symbol Timeout on Trigger ³ ³ The same-symbol timeout is not restarted when the trigger is pulled. The same-symbol timeout is restarted when the trigger is pulled. * Factory Default Configuration 9

17 UPC/EAN CODE TYPES AND DECODE RULES *Bar code descriptions marked with an asterisk ( * ) define a feature that is a factory default. Bar codes marked with a tilde ( ~ ) require the Multi-Code configuration method. *The following contents are for 1D. ³ * Enable UPC/EAN ³ Disable UPC/EAN ³ * Enable UPC-A ³ Disable UPC-A ³ * Enable UPC-E ³ Disable UPC-E ³ * Enable EAN-13 ³ Disable EAN-13 ³ * Enable EAN-8 ³ Disable EAN-8 10

18 CODE TYPES AND DECODE RULES CODE 128 ³ * Enable Code 128 ³ Disable Code 128 ³ Enable UCC/EAN-128 ]C1 Code Formatting - For Coupon Code 128, see page 52. ³ * Disable UCC/EAN 128 ]C1 Code Formatting ³ Ignore <FNC4> Code 128 Characters ³ * Use <FNC4> to Determine Extended ASCII Characters 11

19 CODE TYPES AND DECODE RULES CODE 39 ³ * Enable Code 39 ³ Disable Code 39 ³ ³ Enable MOD 43 Check Digit on Code 39 - The scanner only scans Code 39 bar codes that have a valid Modulo 43 check digit. * Disable MOD 43 Check Digit on Code 39 ³ Enable Full ASCII Code 39 ³ * Disable Full ASCII Code 39 ³ ³ Enable PARAF (Italian Pharmaceutical Codes) Support - Code 39 bar codes are converted to PARAF format. * Disable PARAF Support ³ * Allow PARAF Codes Only ³ Allow Non-PARAF Codes ³ Enable TRI-OPTIC Code ³ * Disable TRI-OPTIC Code ³ * Use Standard Code 39 Framing ³ Try Code 39 Codes Without 5 Bar Multiples 12

20 CODE TYPES AND DECODE RULES CODE 39 ³ Enable ITF/Code 39 Filters ³ * Disable ITF/Code 39 Filters Enable Self-Service Library Code 39 * Disable Self-Service Library Code 39 Transmit MOD 43 Check Digit with Self Service Library Code 39 * Do Not Transmit MOD 43 Check Digit with Self Service Library Code 39 Enable Alternate Code 39 Reference Comparison Check assists with elements that are below the 2 to 1 (wide to narrow) element width requirement. * Normal Code 39 Reference Comparison Check 13

21 CODE TYPES AND DECODE RULES 2 OF 5 CODES ³ * Enable Interleaved 2 of 5 (ITF) ³ Disable Interleaved 2 of 5 (ITF) ³ Enable MOD 10 Check on ITF - The scanner will only scan Interleaved 2 of 5 (ITF) bar codes that have a Modulo 10 check digit. ³ * Disable MOD 10 Check on ITF ³ Allow ITF Null Characters ³ * Do Not Allow ITF Null Characters ³ ³ ³ ~ ITF Symbol Length Lock 1 - To specify a 1 st ITF symbol length lock, scan this bar code and the appropriate code bytes sequence located on page 57. ~ ITF Symbol Length Lock 2 - To specify a 2 nd ITF symbol length lock, scan this bar code and the appropriate code bytes sequence located on page 57. ~ ITF Minimum Symbol Length - To specify a minimum number of ITF characters to be decoded, scan the appropriate code bytes sequence located on page 57. Alternative ITF 1 st Bar Reference * Normal ITF 1 st Bar Reference ³ Enable Standard 2 of 5 14

22 CODE TYPES AND DECODE RULES 2 OF 5 CODES ³ * Disable Standard 2 of 5 ³ ~ Standard 2 of 5 Symbol Length - To specify a minimum number of characters to be decoded, scan this bar code and the appropriate code bytes sequence located on page 57. ³ Enable Matrix 2 of 5 ³ * Disable Matrix 2 of 5 ³ Enable Matrix 2 of 5 Check Digit Requirement ³ * Disable Matrix 2 of 5 Check Digit Requirement ³ Enable 15 Digit Airline 2 of 5 ³ * Disable 15 Digit Airline 2 of 5 ³ Enable 13 Digit Airline 2 of 5 ³ * Disable 13 Digit Airline 2 of 5 ³ Enable Hong Kong 2 of 5 ³ * Disable Hong Kong 2 of 5 15

23 CODE TYPES AND DECODE RULES Enable Follett ITF * Disable Follett ITF CODABAR ³ * Enable Codabar ³ Disable Codabar ³ Enable Dual Field Codabar ³ * Disable Dual Field Codabar CODE 93 ³ * Enable Code 93 ³ Disable Code 93 16

24 CODE TYPES AND DECODE RULES CODE 11 ³ Enable Code 11 ³ * Disable Code 11 ³ * Check for 1 Code 11 Check Digit ³ Check for 2 Code 11 Check Digits ³ * Do Not Check for 2 Code 11 Check Digits ³ Check for 2 Code 11 Check Digits if Code Length is Greater Than 10 Characters TELEPEN ³ Enable Telepen ³ * Disable Telepen ³ Enable ALPHA Telepen ³ * Disable ALPHA Telepen 17

25 CODE TYPES AND DECODE RULES PLESSEY CODES ³ Enable MSI Plessey ³ * Disable MSI Plessey ³ * No MSI Plessey Check Digit - Plessy bar codes will not be tested for a check digit. ³ ³ ³ Enable MSI Plessey MOD 10/10 Check Digit - Test MSI Plessey bar codes for a 2 digit Modulo 10 check digit. * Enable MSI Plessey Mod 10 Check Digit - Test MSI Plessey bar codes for a 1 digit Modulo 10 check digit. Enable UK Plessey ³ * Disable UK Plessey ³ Enabled UK Plessey A to X Conversion ³ * Disabled UK Plessey A to X Conversion PLESSEY CODES ³ * Standard Plessey Stop Characters ³ Accept Bad Plessey Stop Characters 18

26 CODE TYPES AND DECODE RULES ADDITIONAL DECODE FEATURES ³ Enable Double Border Required / Large Intercharacter Space ³ * Disable Double Border Required / Large Intercharacter Space ³ Enable Small Border Required ³ * Disable Small Border ³ ³ ³ ~ Minimum Symbol Length - Single-line default is 3. Combine this code with the proper code bytes (page 57), to specify the minimum number of characters in all non-upc/ean bar codes. ~ Symbol Length Lock - Combine this code with the proper code bytes, to lock the bar code s length into place. Enable Modulus 8 Filter on Bar & Space Counts ³ * Disable Modulus 8 Filter on Bar & Space Counts ³ Handle Code 39 Bad Border ³ * Disable Code 39 Bad Border 19

27 CODE TYPES AND DECODE RULES CONFIGURABLE CODE LENGTHS There are seven bar code lock lengths available. Specific code types can be assigned to a lock length. While in programming mode: 1. Scan the code length lock #1 bar code 2. Scan the three code bytes that represent the code length (page 57). 3. Scan the matching code type lock #1 bar code. 4. Scan the three code bytes that represent the code type. This process can be repeated for lock lengths 2 through 7. ³ ~ Code Length Lock #1 ³ ~ Code Type Lock #1 ³ ~ Code Length Lock #2 ³ ~ Code Type Lock #2 ³ ~ Code Length Lock #3 ³ ~ Code Type Lock #3 ³ ~ Code Length Lock #4 ³ ~ Code Type Lock #4 ³ ~ Code Length Lock #5 ³ ~ Code Type Lock #5 20

28 CODE TYPES AND DECODE RULES CONFIGURABLE CODE LENGTHS ³ ~ Code Length Lock #6 ³ ~ Code Type Lock #6 ³ ~ Code Length Lock #7. ³ ~ Code Type Lock #7. Enable Japanese Multi-Field Disable Japanese Multi-Field 21

29 CODE TYPES AND DECODE RULES *The following contents are for 2D. DATA MATRIX Enable Normal Color Data Matrix Decoding Enable Inverse Color Data Matrix Decoding ³ ³ Enable Normal and Inverse Color Data Matrix Decoding * Disable Data Matrix Decoder ³ ³ Enable Rectangular Data Matrix Symbol Decoding * Disable Rectangular Data Matrix Symbol Decoding ³ ³ * Factory Default Configuration 22

30 CODE TYPES AND DECODE RULES DATA MATRIX Enable Low-Contrast Data Matrix Decoding * Disable Low-Contrast Data Matrix Decoding ³ Improves decoding of low-contrast Data Matrix symbols. ³ Enable Data Matrix Non-Square Modules * Disable Data Matrix Non-Square Modules ³ Improves decoding of Data Matrix symbols when individual modules in the symbol are non-square. ³ Enable Data Matrix Shifted Tiles * Disable Data Matrix Shifted Tiles ³ Improves decoding of Data Matrix symbols when the upper tiles in the symbol are shifted in the symbol relative to the bottom tiles. ³ * Factory Default Configuration Enabling these options will increase decoding time for all bar codes. 23

31 CODE TYPES AND DECODE RULES DATA MATRIX * Enable Data Matrix, Normal Size ³ The following bar codes improve decoding of Data Matrix symbols when the length of a symbol size is small. To disable either of these options scan the Enable Data Matrix Normal Size bar code above. Enable Data Matrix, Small Size Enable Data Matrix Very Small Size ³ ³ * Factory Default Configuration Enabling these options will increase decoding time for all bar codes. 24

32 CODE TYPES AND DECODE RULES QR CODE Enable Normal Video QR Code Enable Inverse Video QR Code ³ ³ Enable Normal and Inverse QR Code * Disable QR Code ³ ³ MAXICODE Enable MaxiCode * Disable MaxiCode ³ ³ * Factory Default Configuration 25

33 CODE TYPES AND DECODE RULES AZTEC Enable Normal Video Aztec Decoding * Disable Normal Video Aztec Decoding ³ ³ Enable Inverse Video Aztec Decoding * Disable Inverse Video Aztec Decoding ³ ³ * Factory Default Configuration 26

34 CODE TYPES AND DECODE RULES AZTEC Enable Aztec Structure Append Decoding * Disable Aztec Structure Append Decoding ³ ³ When this feature is enabled, Aztec barcodes with a structured append header will be stored in the scanner s memory buffer. The scanner will transmit the concatenated message once every component of the structured append barcode has been read. Up to 16 components can be stored. If this feature is disabled, Aztec barcodes with structured append header will be read as normal Aztec barcodes. However, in this case, the structured append header will be sent as part of the barcode data. Code Select and structured append features cannot be used concurrently. If both CodeSelect and structured append are enabled, CodeSelect feature will not work. The CodeSelect timeout setting determines how much time will be allowed between individual components of the same barcode (similar to CodeSelect operation). By default, the scanner will emit an intermediate beep when each component is scanned. When only one scan buffer is enabled, the user will be required to release the trigger after reading each barcode component. * Enable Intermediate Beep Disable Intermediate Beep ³ ³ If the intermediate beep is disabled and the number of scan buffers is increased (compare buffers in MetroSet ) all components of a structured append barcode can be read with a single trigger activation, and only one audible beep will be produced, as if a regular barcode was scanned. * Factory Default Configuration 27

35 CODE TYPES AND DECODE RULES POSTAL Enable Australia Post * Disable Australia Post ³ ³ Enable Japan Post * Disable Japan Post ³ ³ Enable KIX Code * Disable KIX Code ³ ³ * Factory Default Configuration 28

36 CODE TYPES AND DECODE RULES POSTAL Enable PLANET Code * Disable PLANET Code ³ ³ Enable POSTNET Code * Disable POSTNET Post ³ ³ Enable B & B Fielded POSTNET * Disable B & B Fielded POSTNET ³ ³ * Factory Default Configuration 29

37 CODE TYPES AND DECODE RULES POSTAL Enable UPU Decoding * Disable UPU Decoding ³ ³ Enable Royal Mail 4 Code * Disable Royal Mail 4 Code ³ ³ Enable Zero-FCC Australia Post * Disable Zero-FCC Australia Post ³ ³ * Factory Default Configuration 30

38 CODE TYPES AND DECODE RULES CODABLOCK OPTIONS Enable Codablock A * Disable Codablock A ³ ³ Enable Codablock F * Disable Codablock F ³ ³ PDF OPTIONS Enable Transmit \ as \ ³ * Enable Transmit \ as \\ ³ * Factory Default Configuration 31

39 INTERFACES ADDITIONAL INTERFACES Enable Beeper ON/OFF Commands * Disable Beeper ON/OFF Commands ³ Enables beeper on/off commands with internal USB and IBM interfaces. ³ rd Generation IBM 46xx Defaults ³ For this feature to function properly, scan IBM Reserved Code #2 after scanning the 3 rd Generation IBM 46xx Default bar code. IBM Reserved Code #2 ³ Scan IBM Reserve bar code above after scanning the 3 rd Generation IBM 46xx Default bar code. * Factory Default Configuration These features are not for use with the MS

40 INTERFACES ADDITIONAL INTERFACES IBM 46xx-SIOC RS485 Interface Send 30H for Last Block Label Identifier 4680 * Send 00 for Last Block Label Identifier 4680 ³ For PDF codes only. ³ For PDF codes only. IBM-OEM USB Interface Send 30H for Last Block Label Identifier USB * Send 00 for Last Block Label Identifier USB ³ For PDF codes only. ³ For PDF codes only. Full Speed USB Keyboard Interface Enable Full Speed USB Keyboard Interface Defaults ³ * Factory Default Configuration These features are not for use with the MS

41 PREFIXES/SUFFIXES Scan the Enter Configuration Mode bar code before trying to set these features (see the Multi-Code Method on page 69). USER CONFIGURABLE PREFIXES, ALL DATA ³ ~ Configurable Prefix Character #1 - A prefix ID can be added and assigned for data transmission. Use this code with a code byte sequence (see page 57) that represents the desired character. ³ ~ Configurable Prefix Character #2 - Assigns a second configurable prefix character. ³ ~ Configurable Prefix Character #3 - Assigns a third configurable prefix character. ³ ~ Configurable Prefix Character #4 - Assigns a fourth configurable prefix character. ³ ~ Configurable Prefix Character #5 - Assigns a fifth configurable prefix character. ³ ~ Configurable Prefix Character #6 - Assigns a sixth configurable prefix character. ³ ~ Configurable Prefix Character #7 - Assigns a seventh configurable prefix character. ³ ~ Configurable Prefix #8 - Assigns an eighth configurable prefix character. ³ ~ Configurable Prefix Character #9 - Assigns a ninth configurable prefix character. ³ ~ Configurable Prefix Character #10 - Assigns a tenth configurable prefix character. ³ * Clear All User Configurable Prefixes 34

42 PREFIXES/SUFFIXES USER CONFIGURABLE ID CHARACTERS, CODE SPECIFIC ³ * Use Configurable Code ID Bytes as Prefixes - User configured, code specific ID bytes are transmitted before the data. If using prefixes, user configured suffixes cannot be used. ³ Use Configurable Code ID Bytes as Suffixes - User configured, code specific ID bytes are transmitted after the data. If using suffixes, user configured prefixes can not be used. Enter configuration mode then scan this bar code followed by the three code byte bar codes (page 57) that represent a unique ID character to be associated with this bar code type. ³ ~ Configurable UPC-A ID ³ ~ Configurable UPC-E ID ³ ~ Configurable EAN-8 ID ³ ~ Configurable EAN-13 ID ³ ~ Configurable Code 39 ID ³ ~ Configurable Code 128 ID ³ ~ Configurable Code 93 ID ³ ~ Configurable Code 11 ID 35

43 PREFIXES/SUFFIXES USER CONFIGURABLE ID CHARACTERS, CODE SPECIFIC Enter configuration mode then scan this bar code followed by the three code byte bar codes (page 57) that represent a unique ID character to be associated with this bar code type. ³ ~ Configurable TRI-OPTIC ID ³ ~ Configurable Standard 2 of 5 ID ³ ~ Configurable Interleaved 2 of 5 ID ³ ~ Configurable Matrix 2 of 5 ID ³ ~ Configurable Airline 2 of 5 ID ³ ~ Configurable MSI Plessey ID ³ ~ Configurable UK Plessey ID ³ ~ Configurable Codabar ID ³ * Clear All Configurable Code Specific ID s - Clears all unique ID characters previously identified. ³ Enable Teraoka ID ³ * Disable Teraoka ID Enable Taiwan 7-11 ID * Disable Taiwan 7-11 ID 36

44 PREFIXES/SUFFIXES STANDARD PREFIX CHARACTERS ³ Enable STX Prefix - The scanner will transmit a Start of TeXt (ASCII 02H) before each bar code. ³ * Disable STX Prefix ³ Enable Rochford-Thomson Mode ³ * Disable Rochford-Thomson Mode ³ Enable AIM ID Characters ³ * Disable AIM ID Characters ³ ³ Enable UPC Prefix ID - The scanner will transmit a prefix before any UPC/EAN bar code. The prefixes are A (UPC-A), E0 (UPC-E), F (EAN-13), and FF (EAN-8). * Disable UPC Prefix ID. ³ Enable NCR Prefix ID - The scanner will transmit a prefix before the following code types. The prefixes are as follows: A (UPC-A), E0 (UPC-E), FF (EAN-8), F (EAN 13), B1 (Code 39) B2 (ITF), B3 (Code 128 and other codes). ³ * Disable NCR Prefix ID Enable NCR Prefix Character ³ ³ Enable Nixdorf ID Characters - This option transmits code identities before each bar code for many Siemen/Nixdorf registers. * Disable Nixdorf ID Characters 37

45 PREFIXES/SUFFIXES STANDARD PREFIX CHARACTERS ³ Enable SANYO ID Characters ³ * Disable SANYO ID Characters ³ Enable Manufacturer ID Prefix - Transmits METROLOGIC before all bar code data. ³ * Disable Manufacturer ID Prefix ³ Enable C Prefix ³ * Disable C Prefix ³ Enable $ Prefix ID for UPC/EAN ³ * Disable $ Prefix ID for UPC/EAN ³ Enable Tab Prefix - The scanner will transmit a TAB (ASCII 09H) before each bar code. ³ * Disable Tab Prefix ³ Enable SNI Beetle Mode ³ * Disable SNI Beetle Mode ³ Enable Cipher 1021 IDs ³ * Disable Cipher 1021 IDs 38

46 PREFIXES/SUFFIXES STANDARD SUFFIX CHARACTERS ³ * Enable CR Suffix - The scanner transmits a carriage return after each bar code. ³ Disable CR Suffix. ³ ³ * Enable LF Suffix - The scanner transmits a line feed after each bar code. Disabled when keyboard wedge defaults are loaded. Disable LF Suffix. ³ Enable Tab Suffix - The scanner will transmit a TAB (ASCII 09H) after each bar code. ³ * Disable Tab Suffix ³ Enable ETX Suffix - The scanner will transmit End of TeXt (ASCII 03H) after the bar code date. ³ * Disable ETX Suffix ³ ³ Enable UPC Suffix ID - The scanner will transmit a suffix after any UPC/EAN bar code. The suffixes are A (UPC-A), E (UPC-E), F (EAN-13) and F (EAN-8). * Disable UPC Suffix ID Enable Tec 7-11 IDs * Disable Tec 7-11 IDs 39

47 PREFIXES/SUFFIXES LONGITUDINAL REDUNDANCY CHECK A Longitudinal Redundancy Check (LRC) is an error checking character that is calculated across a sequence of data characters. It is determined by exclusive ORing (XOR) the characters to be checked, starting with an initial value of 00H. The result, an LRC byte is then transmitted following the data stream and used by the receiving computer to determine if the information was received correctly. In the scanner s case, XOR is performed prior to adding parity bits. When the LRC is enabled, the scanner defaults to starting the LRC on the second byte of information transmitted. Optionally, the calculation can start on the first byte transmitted. ³ ³ Enable Transmit of LRC Calculation - The scanner outputs on LRC check character after the bar code. * Disable Transmit of LRC Calculation. ³ ³ * Start LRC on First Byte - The scanner will calculate the LRC check digit starting with the first character. Start LRC on Second Byte - The scanner will calculate the LRC check digit starting with the second character. BLOCK CHECK CHARACTER * Enable NCR BCC Disable NCR BCC 40

48 PREFIXES/SUFFIXES CHARACTER REPLACEMENTS To replace a character: 1. Scan the enter/exit configuration mode bar code (page 69). 2. Scan the character to replace code (shown below). 3. Scan the ASCII code byte value of the character you wish to replace (refer to the ASCII Reference Table in the Code Byte Usage section of this manual). 4. Scan the replacement character bar code (shown below). 5. Scan the ASCII code byte value of the replacement character. 6. Scan the enter/exit configuration mode bar code (page 69). ³ ~ Character to Replace ³ ~ Replacement Character ³ No Replacement 41

49 PREFIXES/SUFFIXES USER CONFIGURABLE SUFFIXES, ALL DATA Note: Scan the Enter/Exit Configuration mode code before trying to set this feature. Refer to Multi-Code Method on page 69. ³ ~ Configurable Suffix Character #1 - A suffix ID can be added and assigned for data transmission. Use this code with a 3 code byte sequence (page 57) that represents the desired character. ³ ~ Configurable Suffix Character #2 - Assigns a second configurable suffix character. ³ ~ Configurable Suffix Character #3 - Assigns a third configurable suffix character. ³ ~ Configurable Suffix Character #4 - Assigns a fourth configurable suffix character. ³ ~ Configurable Suffix Character #5 - Assigns a fifth configurable suffix character. ³ ~ Configurable Suffix Character #6 - Assigns a sixth configurable suffix character. ³ ~ Configurable Suffix Character #7 - Assigns a seventh configurable suffix character. ³ ~ Configured Suffix Character #8 - Assigns an eighth configurable suffix character. ³ ~ Configurable Suffix Character #9 - Assigns a ninth configurable suffix character. ³ ~ Configurable Suffix Character #10 - Assigns a tenth configurable suffix character. ³ * Clear All User Configurable Suffixes 42

50 PREFIXES/SUFFIXES SPECIAL FORMATS ³ Enable SINEKO Mode ³ * Disable SINEKO Mode ³ Enable Newcode Formatting Mode A ³ * Disable Newcode Formatting Mode A ³ Enable Newcode Formatting Mode B ³ * Disable Newcode Formatting Mode B ³ Remove All Leading Zero s ³ * Don t Remove Leading Zero s ³ Enable MS951 CAPS Lock ³ * Disable MS951 CAPS Lock ³ Enable HCA Parsing ³ Disable HCA Parsing 43

51 CODE FORMATTING UPC/EAN FORMATTING ³ * Transmit UPC-A Check Digit ³ Do Not Transmit UPC-A Check Digit ³ Transmit UPC-E Check Digit ³ * Do Not Transmit UPC-E Check Digit ³ Expand UPC-E to 12 Digits - Expand UPC-E bar codes to the 12 digit equivalent, UPC-A bar codes. ³ * Do Not Expand UPC-E to 12 Digits * Send Number System on Expanded UPC E Do not Send Number System on Expanded UPC E ³ Enable GTIN Formatting ³ * Disable GTIN Formatting ³ ³ Convert UPC-A to EAN-13 - The scanner converts UPC-A to EAN-13 by transmitting a leading zero before the bar code. * Do Not Convert UPC-A to EAN-13 ³ Transmit Lead Zero on UPC-E - This option will transmit a zero before each UPC-E bar code. ³ * Do Not Transmit Lead Zero on UPC-E 44

52 CODE FORMATTING ³ ³ Convert EAN-8 to EAN-13 - The scanner will transmit five zeros before the bar code to convert EAN-8 to EAN-13. * Do Not Convert EAN-8 to EAN-13 ³ * Transmit UPC-A Number System ³ Do Not Transmit UPC-A Number System ³ * Transmit UPC-A MFR # ³ Do Not Transmit UPC-A MFR # ³ * Transmit UPC-A ITEM # ³ Do Not Transmit UPC-A ITEM # ³ * Transmit EAN-8 Check Digit ³ Do Not Transmit EAN-8 Check Digit ³ * Transmit EAN-13 Check Digits - The scanner will transmit EAN-13 Check Digit. ³ Do Not Transmit EAN-13 Check Digit. 45

53 CODE FORMATTING CODABAR FORMATTING ³ Transmit Codabar Start/Stop Characters - Transmits Codabar s Start/stop characters before and after each bar code. ³ * Do Not Transmit Codabar Start/Stop * Normal Codabar Start/Stop Characters Enable Transmit Codabar Start/Stop Characters as Lower Case Characters ³ ³ Enable CLSI Editing - Works only with 14 digit Codabar type lengths. This option will perform CLSI type editing before the information is transmitted to the host. * Do Not Enable CLSI Editing ³ Enable Codabar Mod-16 Check Digit ³ * Disable Codabar Mod-16 Check Digit ³ Enable Codabar 7-Check Check Digit ³ * Disable Codabar 7-Check Check Digit ³ * Transmit Codabar Check Digit ³ Don t Transmit Codabar Check Digit 46

54 CODE FORMATTING CODE 39 FORMATTING ³ ³ Transmit Mod 43 Check Digit on Code 39 - This feature works in conjunction with Mod 43 Check Digit on Code 39 option, page 12. Both must be enabled for this feature to work. * Do Not Transmit Mod 43 Check Digit on Code 39 ³ Transmit Code 39 Stop/Start Characters - The scanner transmits Code 39 s start and stop characters before and after each bar code. ³ * Do Not Transmit Code 39 Stop/Start Characters. ³ Transmit an A (41H) Prefix if Italian Pharmaceutical. ³ * Do not Transmit an A (41H) Prefix if Italian Pharmaceutical CODE 11 FORMATTING ³ Transmit Code 11 Check Digit - This bar code will transmit Code 11 check characters when used with Enabled Code 11 page 17. ³ * Do Not Transmit Code 11 Check Digit TELEPEN ³ Enable Convert Telepen ^L to E ³ * Disable Convert Telepen ^L to E 47

55 CODE FORMATTING PLESSEY ³ Transmit UK Plessey Check Digit - The scanner will transmit UK Plessey Check Digit characters and must be used with the UK Plessey option. ³ * Do Not Transmit UK Plessey Check Digit ³ Enable UK Plessey Special Format ³ Disable UK Plessey Special Format ³ Transmit MSI Plessey Check Digit - This option works in conjunction with one or both of the Enabled MSI Plessey Mod options on page 18. ³ * Do Not Transmit MSI Plessey Check Digit 2 OF 5 CODE FORMATTING ³ Transmit Mod 10 Check Digit on ITF - The scanner transmits interleaved 2 of 5 (ITF) Mod 10 check character. ³ * Do Not Transmit Mod 10 Check Digit on ITF - Works in conjunction with Mod 10 check on ITF. Both must be enabled for this feature to work. ³ Transmit Matrix 2 of 5 Check Digit ³ * Do Not Transmit Matrix 2 of 5 Check Digit 48

56 ISBT CODE 128 IMPLEMENTATION CONFIGURATION MODE BAR CODES ³ Enable ISBT Code 128 ³ Disable ISBT Code 128 These bar codes are used to enable/disable a special transmit mode as outlined in section of the ISBT-128 Specification. This output method allows the user to confirm independently the accuracy of the Code-128 check digit. ³ Enable ISBT Special Transmit ³ Disable ISBT Special Transmit These bar codes can be used to disable the transmission of the ISBT Code 128 data identifiers. When this option is selected, the first two data characters are removed from the data stream (ID characters) unless the ISBT bar code scanned contains the Donation Identification Number identifiers. In this instance only the first ID character is removed from the Donation ID Number. The second is regarded as normal data. ³ Don t Transmit ISBT ID s ³ * Transmit ISBT Identifiers These bar codes are used to convert and transmit the Mode 37,2 check digit from the flag digits of the Donation Identification Number provided the check digit is contained in the flag digits. Transmission of the Donation Identification number will be the same except for the last two digits, which are converted into a single check sum character. ³ Convert Flag Digits to Mod 37, 2 CD ³ * Normal Flag Digit Transmission 49

57 SUPPLEMENTS ³ Enable Two Digit Supplements ³ * Disable Two Digit Supplements ³ ³ * Enable Two Digit Redundancy - The scanner will scan the bar code plus the 2 digit add on twice before accepting data. Disable Two Digit Redundancy ³ Enable Five Digit Supplements ³ * Disable Five Digit Supplements ³ ³ Enable Five Digit Redundancy - The scanner will scan the bar code plus the 5 digit add on twice before accepting data. * Disable Five Digit Redundancy ³ Supplements are Required - All UPC/EAN labels that are scanned must have a supplement. ³ * Supplements are Not Required ³ Enable Remote Supplement Required - MS9500 & MS6200 not supported. ³ * Disable Remote Supplement Required - MS9500 & MS6200 not supported. Enable Bookland (979) Supplement Required * Disable Bookland (979) Supplement Required 50

58 SUPPLEMENTS ³ Enable Bookland (978) Supplement Required ³ * Disable Bookland (978) Supplement Required ³ Enable 977 (2 Digit) Supplement Required - The scanner will require a 2 digit supplement to be scanned when an EAN-13 code begins with 977. ³ * Disable 977 (2 Digit) Supplement Required ³ Enable 378/379 French Supplement Required ³ * Disable 378/379 French Supplement Required ³ Enable 414/419 German Bookland Supplement Required ³ * Disable 414/419 German Bookland Supplement Required ³ Enable 434/439 German Supplement Required ³ * Disable 434/439 German Supplement Required ³ Enable # System 2 Requires Supplements ³ * Disable # System 2 Requires Supplements ³ Enable UPC # System 5 Requires Supplements ³ * Disable UPC # System 5 Requires Supplements 51

59 SUPPLEMENTS ³ * Enable 2 Digit Supplements with 37x, 43x, or UPC # System 5 ³ Disable 2 Digit Supplements with 37x, 43x, or UPC # System 5 ³ * Enable 5 Digit Supplements with 37x, 43x, or UPC # System 5 ³ Disable 5 Digit Supplements with 37x, 43x, or UPC # System 5 ³ Enable Coupon Code 128 ³ * Disable Coupon Code 128 ³ ³ Enable Code 128 ]C1 Extended Code Format - The scanner transmits a ]C1 at the beginning of the Code 128 portion of the coupon code. * Disable Code 128 ]C1 Extended Code Format. ³ ³ Enable Code 128 Group Separators A GS (1DH) character will be transmitted with coupon Code 128 codes. * Disable Code 128 Group Separators ³ msec to Find Supplemental - The scanner will allot 400 milliseconds to find an add on after a main UPC/EAN bar code has been scanned. ³ msec to Find Supplemental - The scanner will allot 200 milliseconds to find an add on after a main UPC/EAN bar code has been scanned. ³ * 100 msec to Find Supplemental - The scanner will allot 100 milliseconds to find an add on after a main UPC/EAN bar code has been scanned. 52

60 SUPPLEMENTS ³ Enable Code ID s with Supplements ³ * Disable Code ID s with Supplements ³ * Beep Once on Supplements ³ Beep Twice on Supplements ³ Enable ISBN Check Digit Transmission - Not available with all models. ³ Disable ISBN Check Digit Transmission ³ Enable Bookland to ISBN Conversion - Not available with all models ³ * Disable Bookland to ISBN Conversion ³ Enable ISBN Re-Formatting ³ * Disable ISBN Re-Formatting Enable Bookland to ISBN 979 Conversion * Disable Bookland to ISBN 979 Conversion * Normal ISBN Re-Formatting 13 Digit ISBN Re-Formatting 53

61 SUPPLEMENTS ³ Disable Supplementals when CodeGate Button is Pressed - Available for MS9540 scanners only. Requires standard Code Gate be inactive in and out of stand. ³ * CodeGate Does Not Affect Supplemental Scanning - Available for MS9540 scanners only. No Supplement Checking if EAN-13 Code is just scanned * Normal Supplement Checking 54

62 USB ³ Enable USB Interface ³ Enable Low Speed USB Defaults This feature is limited to Unitech scanners without integrated Low Speed USB electronics. Load Integrated Full Speed USB Keyboard Emulation Defaults Load Integrated Full Speed USB IBM/OEM Defaults Load Integrated Low Speed USB OPOS Defaults limited to scanners with internal Low Speed USB interfaces with specific software versions. IBM OEM Scanner 4B00h Handheld Full Speed USB Only IBM OEM Scanner 4A00h Flatbed Full Speed USB Only Enable USB Keyboard Emulation Mode Enable Uni-Directional USB Serial Emulation Mode Enables Uni-Directional USB Serial Emulation Mode. Enables Bi-Directional USB Serial Emulation Mode. Enable Bi-Directional USB Serial Emulation Mode Enables Bi-Directional USB Serial Emulation Mode. 55

63 USB If the Recall Defaults bar code is scanned while reconfiguring the scanner, the scanner configuration will revert to the default setting, USB Keyboard Emulation Mode. Rescan the Bi-Directional or Uni-Directional USB Serial Emulation Mode bar code to enable the appropriate Serial Emulation Mode. ³ Enable Barcode ID ³ ³ ³ ³ ³ ³ Disable Barcode ID Enable USB Reserve Code #1 Disable USB Reserve Code #1 Enable USB Reserve Code #2 Disable USB Reserve Code #2 Sears USB Defaults ³ Sears Aux Defaults Enable IBM 1520 Code Flag Emulation UPC code ID and ITF code ID remain the same but all other code ID is transmitted as Code 39 (IBM OEM Scanner Modes). Disable IBM 1520 Code Flag Emulation 56

64 CODE BYTES USAGE The features that use these code bytes for configuration require that the scanner be in Configuration Mode. The Enter/Exit Configuration Mode bar code (on page 69) must be scanned before starting the configuration cycle. Example: User configurable prefix/suffix characters can be saved into the scanner by scanning the 3 digit decimal equivalent of the ASCII character into the appropriate character location with the code byte bar codes. To add an Asterisk (*) as a Prefix scan the following bar codes in order. 1. Enter/Exit Configuration Mode (3 beeps) 2. Configurable Prefix #1 (1 beep) 3. Code Byte 0 (1 beep) 4. Code Byte 4 (2 beeps) 5. Code Byte 2 (3 beeps) 6. Enter/Exit Configuration Mode (3 beeps) CODE BYTES 0-9 ³ 0 Code Byte 0 ³ 1 Code Byte 1 ³ 2 Code Byte 2 ³ 3 Code Byte 3 ³ 4 Code Byte 4 ³ 5 Code Byte 5 ³ 6 Code Byte 6 ³ 7 Code Byte 7 ³ 8 Code Byte 8 ³ 9 Code Byte 9 57

65 CODE BYTES USAGE RESERVED CODES ³ ~ Enable Reserved Code - Contact Metrologic for information about this feature. ³ ~ Disable Reserved Code CODE TYPE TABLE Code Byte Code Types 004 UPC-A 002 UPC-E 003 EAN EAN Code Codabar 082 Interleaved 2 of Code Code MSI Plessey 092 Code Airline 2 of 5 (15 digits) 094 Matrix 2 of Telepen 096 UK Plessey 099 TRI-OPTIC 098 Standard 2 of Airline (13 digits) 58

66 CODE BYTES USAGE ASCII REFERENCE TABLE HEX Value Decimal Value/ Code Byte Value Character Control Keyboard Eqv SOH A STX B ETX C EOT D ENQ E ACK F BEL G BS H HT I 0A 010 LF J 0B 011 VT K 0C 012 FF L 0D 013 CR M 0E 014 SO N 0F 015 SI DLE P DC1 Q DC2 R DC3 S DC4 T NAK U SYN V ETB W CAN X EM Y 1A 026 SUB Z 1B 027 ESC [ 1C 028 FS \ 59

67 CODE BYTES USAGE ASCII REFERENCE TABLE HEX Value Decimal Value/ Code Byte Value Character Control Keyboard Eqv 1D 029 GS ^ 1E 030 RS _ 1F 031 US space,blank SP ! # $ % & apostrophe ( ) 2A 042 * 2B C 044, comma 2D minus 2E 046. period 2F 047 / number zero number one A 058 : 3B 059 ; 60

68 CODE BYTES USAGE ASCII REFERENCE TABLE HEX Value Decimal Value/ Code Byte Value Character Control Keyboard Eqv 3C 060 < less than 3D E 062 > greater than 3F 063? 40 shift P A B C D E F G H I letter l 4A 074 J 4B 075 K 4C 076 L 4D 077 M 4E 078 N 4F 079 O letter O P Q R S T U V W X Y 61

69 CODE BYTES USAGE ASCII REFERENCE TABLE HEX Value Decimal Value/ Code Byte Value Character 5A 090 Z Control Keyboard Eqv 5B 091 [ shift K 5C 092 \ shift L 5D 093 ] shift M 5E 094 ^ à,shift N 5F 095 _, shift 0, underscore accent grave a b c d e f g h I 6A 106 j 6B 107 k 6C 108 l 6D 109 m 6E 110 n 6F 111 o p q r s t u v w x 62

70 CODE BYTES USAGE ASCII REFERENCE TABLE HEX Value Decimal Value/ Code Byte Value Character y 7A 122 z 7B 123 { Control Keyboard Eqv 7C 124 vertical slash 7D 125 } alt mode 7E 126 ~ (alt mode) 7F 127 DEL delete, rubout EXTENDED KEY CODE REFERENCE TABLE Key At Scan Code PS2 Scan Code 3151 Prefix/Suffix Value Hex = Decimal 75H 48H 63H 80H = H 50H 60H 81H = H 4DH 6AH 82H = 130 6BH 4BH 61H 83H = 131 Insert 70H 52H 67H 84H = 132 Delete 71H 53H 64H 85H = 133 Home 6CH 47H 6EH 86H = 134 End 69H 4FH 00H 87H = 135 Page Up 7DH 49H 00H 88H = 136 Page Down 7AH 51H 00H 89H = 137 Right Alt 11H 38H 00H 8AH = 138 Right Ctrl 14H 1DH 39H 8BH = 139 Reserved 00H 00H 00H 8CH = 140 Reserved 00H 00H 00H 8DH 141 Numeric Keypad Enter 5AH 1CH 79H 8EH = 142 Numeric Keypad/ 4AH 35H 00H 8FH = 143 F1 05H 3BH 07H 90H = 144 F2 06H 3CH 0FH 91H = 145 F3 04H 3DH 17H 92H = 146 F4 0CH 3EH 1FH 93H =

71 CODE BYTES USAGE EXTENDED KEY CODE REFERENCE TABLE Key At Scan Code PS2 Scan Code Prefix/Suffix Value Hex = Decimal F5 03H 3FH 27H 94H = 148 F6 0BH 40H 2FH 95H = 149 F7 83H 41H 37H 96H = 150 F8 0AH 42H 3FH 97H = 151 F9 01H 43H 47H 98H = 152 F10 09H 44H 4FH 99H = 153 F11 78H 57H 56H 9AH = 154 F12 07H 58H 5EH 9BH = 155 Numeric + 79H 4EH 00H 9CH = 156 Numeric - 7BH 4AH 7CH 9DH = 157 Numeric * 7CH 37H 00H 9EH = 158 Caps Lock 58H 3AH 14H 9FH = 159 Num Lock 77H 45H 00H A0H = 160 Left alt 11H 38H 00H A1H = 161 Left Ctrl 14H 1DH 11H A2H = 162 Left Shift 12H 2AH 12H A3H = 163 Right Shift 59H 36H 59H A4H = 164 Print Screen Multiple 00H 00H A5H = 165 Tab ODH OFH 0DH A6H = 166 Shift Tab 8DH 8FH 65H A7H = 167 Enter 5AH 1CH 5AH A8H = 168 ESC 76H 01H 08H A9H = 169 Left ALT Make 11H 36H 00H AAH = 170 Left ALT Break 11H B6H 00H ABH = 171 Left CTRL Make 14H 1DH 00H ACH = 172 Left CTRL Break 14H 9DH 00H ADH = 173 *Left ALT + 1 character 11H 36H 00H AEH = 174 *Left Crtl + 1 character 14H 1DH 00H AFH = 175 *Send 58H C0H = 192 Clear 6FH C1H = 193 Jump 76H C2H = 194 Send Line 7EH C3H = 195

72 CODE BYTES USAGE EXTENDED KEY CODE REFERENCE TABLE Erase EOF 6DH C4H = 196 Send Make Only 58H C5H = 197 *Example: 1st Configurable Prefix = 174 2nd Configurable Prefix = 065 Scanner will transmit <left ALT Make> A <Left ALT Break> 65

73 ENTER/EXIT CONFIGURATION MODE BAR CODE Enter Exit Configuration Mode ³

74 RSS BAR CODE IMPLEMENTATION ³ Double Border Required - When scanning RSS bar codes, it is recommended that double border requirements be enabled because of the large spaces often found in RSS symbologies. ³ Enable RSS 14 ³ * Disable RSS 14 ³ * Transmit RSS 14 Check Digit ³ Do Not Transmit RSS 14 Check Digit ³ * Transmit RSS 14 Application ID - Application Identifier 01 is transmitted by default. ³ Do Not Transmit RSS 14 Application ID ³ * Transmit RSS 14 Symbology ID - Symbology Identifier ]e0 is transmitted by default. ³ Do Not Transmit RSS 14 Symbology 67

75 RSS BAR CODE IMPLEMENTATION RSS LIMITED BAR CODES ³ Enable RSS Limited ³ * Disable RSS Limited ³ * Transmit RSS Limited CD ³ Do Not Transmit RSS Limited CD ³ ³ * Transmit RSS Limited Application ID - Application identifier 01 is transmitted by default. Do Not Transmit RSS Limited Application ID ³ * Transmit RSS Limited Symbology ID - Symbology identifier ]e0 is transmitted by default. ³ Do Not Transmit RSS Limited Symbology ID RSS EXPANDED BAR CODES ³ Enable RSS Expanded ³ * Disable RSS Expanded ³ * Transmit RSS Expanded Symbol ID - Symbology identifier ]e0 is transmitted by default. ³ Do Not Transmit RSS Expanded Symbol ID 68

76 Multi-Code Method BAR CODE CONFIGURATION METHODS All features can be enabled or disabled using the Multi-Code Method. A feature marked with a tilde ( ~ ) requires the Multi-Code Method. 1. Power up the scanner. 2. Scan the enter/exit configuration mode bar code (3 beeps). 3. Scan the bar code for the desired feature (1 beep). Multiple features can be enabled/disabled before scanning the enter/exit configuration mode bar code. 1. Scan the enter/exit configuration mode bar code (3 beeps) and save the new configuration. To abort a configuration change, power off the scanner before scanning the enter/exit code. Enter/Exit Configuration Mode ³

77 UPC-A Enable/Disable UPC-A To enable or disable UPC-A, scan the appropriate bar code below. Enable UPC-A Disable UPC-A Transmit UPC-A Check Digit The check digit is the last character of the symbol used to verify the integrity of the data. Scan the appropriate bar code below to transmit the bar code data with or without the UPC-A check digit. It is always verified to guarantee the integrity of the data. Transmit UPC-A Check Digit Do Not Transmit UPC-A Check Digit 70

78 UPC-A UPC-A Preamble Preamble characters are part of the UPC symbol, and include Country Code and System Character. There are three options for transmitting a UPC-A preamble to the host device: transmit System Character only, transmit System Character and Country Code ( 0 for USA), and transmit no preamble. Select the appropriate option to match the host system. System Character System Character & Country Code No Preamble 71

79 UPC-E Enable/Disable UPC-E To enable or disable UPC-E, scan the appropriate bar code below. Enable UPC-E Disable UPC-E Transmit UPC-E Check Digit The check digit is the last character of the symbol used to verify the integrity of the data. Scan the appropriate bar code below to transmit the bar code data with or without the UPC-E check digit. It is always verified to guarantee the integrity of the data. Transmit UPC-E Check Digit Do Not Transmit UPC-E Check Digit 72

80 UPC-E UPC-E Preamble Preamble characters are part of the UPC symbol, and include Country Code and System Character. There are three options for transmitting a UPC-E preamble to the host device: transmit System Character only, transmit System Character and Country Code ( 0 for USA), and transmit no preamble. Select the appropriate option to match the host system. System Character System Character & Country Code No Preamble 73

81 CODE 39 Enable/Disable Code 39 To enable or disable Code 39, scan the appropriate bar code below. Enable Code 39 Disable Code 39 Code 39 Check Digit Verification When this feature is enabled, the decoder checks the integrity of all Code 39 symbols to verify that the data complies with specified check digit algorithm. Only Code 39 symbols which include a modulo 43 check digit are decoded. Enable this feature if the Code 39 symbols contain a Modulo 43 check digit. Enable Code 39 Check Digit Disable Code 39 Check Digit 74

82 CODE 39 Transmit Code 39 Check Digit Scan a bar code below to transmit Code 39 data with or without the check digit. Transmit Code 39 Check Digit (Enable) Do Not Transmit Code 39 Check Digit (Disable) Code 39 Full ASCII Conversion Code 39 Full ASCII is a variant of Code 39 which pairs characters to encode the full ASCII character set. To enable or disable Code 39 Full ASCII, scan the appropriate bar code below. Enable Code 39 Full ASCII Disable Code 39 Full ASCII 75

83 UPC-E1 Enable/Disable UPC-E1 To enable or disable UPC-E1, scan the appropriate bar code below. Enable UPC-E1 Disable UPC-E1 Transmit UPC-E1 Check Digit The check digit is the last character of the symbol used to verify the integrity of the data. Scan the appropriate bar code below to transmit the bar code data with or without the UPC-E1 check digit. It is always verified to guarantee the integrity of the data. Transmit UPC-E1 Check Digit Do Not Transmit UPC-E1 Check Digit 76

84 UPC-E1 UPC-E1 Preamble Preamble characters are part of the UPC symbol, and include Country Code and System Character. There are three options for transmitting a UPC-E1 preamble to the host device: transmit System Character only, transmit System Character and Country Code ( 0 for USA), and transmit no preamble. Select the appropriate option to match the host system. System Character System Character & Country Code No Preamble 77

85 EAN-13/JAN-13 Enable/Disable EAN-13/JAN-13 To enable or disable EAN-1 3/JAN-3, scan the appropriate bar code below. Enable EAN-13/JAN-13 Disable EAN-13/JAN-13 78

86 BOOKLAND EAN Enable/Disable Bookland EAN To enable or disable Bookland EAN, scan the appropriate bar code below. Enable Bookland EAN Disable Bookland EAN 79

87 EAN-8/JAN-8 Enable/Disable EAN-8/JAN-8 To enable or disable EAN-8/JAN-8, scan the appropriate bar code below. Enable EAN-8/JAN-8 Disable EAN-8/JAN-8 80

88 CODE 128 Enable/Disable Code 128 To enable or disable Code 1 28, scan the appropriate bar code below. Enable Code 128 Disable Code

89 UCC/EAN-128 Enable/Disable UCC/EAN-128 To enable or disable UCC/EAN-1 28, scan the appropriate bar code below. Enable UCC/EAN-128 Disable UCC/EAN

90 ISBT 128 Enable/Disable ISBT 128 ISBT 28 is a variant of Code 28 used in the blood bank industry. Scan a bar code below to enable or disable ISBT 28. If necessary, the host must perform concatenation of the ISBT data. Enable ISBT 128 Disable ISBT

91 CONVERT UPC-E TO UPC-A Convert UPC-E to UPC-A (Enable/Disable) Enable this to convert UPC-E (zero suppressed) decoded data to UPC-A format before transmission. After conversion, the data follows UPC-A format and is affected by UPC-A programming selections (e.g., Preamble, Check Digit). When disabled, UPC-E decoded data is transmitted as UPC-E data, without conversion. Convert UPC-E to UPC-A (Enable) Convert UPC-E to UPC-A (Disable) 84

92 CONVERT UPC-E1 TO UPC-A Convert UPC-E1 to UPC-A (Enable/Disable) Enable this to convert UPC-E1 decoded data to UPC-A format before transmission. After conversion, the data follows UPC-A format and is affected by UPC-A programming selections (e.g., Preamble, Check Digit). When disabled, UPC-E1 decoded data is transmitted as UPC-E1 data, without conversion. Convert UPC-E1 to UPC-A (Enable) Convert UPC-E1 to UPC-A (Disable) 85

93 CONVERT CODE 39 TO CODE 32 Convert Code 39 to Code 32 (Enable/Disable) Code 32 is a variant of Code 39 used by the Italian pharmaceutical industry. Scan the appropriate bar code below to enable or disable converting Code 39 to Code 32. Convert Code 39 to Code 32 (Enable) Convert Code 39 to Code 32 (Disable) 86

94 CONVERT I 2 OF 5 TO EAN-13 Convert I 2 of 5 to EAN-13 (Enable/Disable) Enable this parameter to convert 1 4-character I 2 of 5 codes to EAN-3, and transmit to the host as EAN-3. To accomplish this, the I 2 of 5 code must be enabled, and the code must have a leading zero and a valid EAN-3 check digit. Convert I 2 of 5 to EAN-13 (Enable) Convert I 2 of 5 to EAN-13 (Disable) 87

95 TRIOPTIC CODE 39 Enable/Disable Trioptic Code 39 Trioptic Code 39 is a variant of Code 39 used in the marking of computer tape cartridges. Trioptic Code 39 symbols always contain six characters. To enable or disable Trioptic Code 39, scan the appropriate bar code below. Enable Trioptic Code 39 Disable Trioptic Code 39 88

96 DISCRETE 2 OF 5 Enable/Disable Discrete 2 of 5 To enable or disable Discrete 2 of 5, scan the appropriate bar code below. Enable Discrete 2 of 5 Disable Discrete 2 of 5 89

97 CODABAR Enable/Disable Codabar To enable or disable Codabar, scan the appropriate bar code below. Enable Codabar Disable Codabar 90

98 MSI Enable/Disable MSI To enable or disable MSI, scan the appropriate bar code below. Enable MSI Disable MSI 91

99 POSTAL CODE SYMBOLOGIES US Postnet To enable or disable US Postnet, scan the appropriate bar code below. Enable US Postnet Disable US Postnet UK Postal To enable or disable UK Postal, scan the appropriate bar code below. Enable UK Postal Disable UK Postal 92

100 POSTAL CODE SYMBOLOGIES Japan Postal To enable or disable Japan Postal, scan the appropriate bar code below. Enable Japan Postal Disable Japan Postal RSS 14 (Reduced Space Symbology) The variants of RSS are RSS 1 4, RSS Expanded, and RSS Limited. The limited and expanded versions have stacked variants. Scan the appropriate bar code below to enable or disable RSS 14. Enable RSS 14 Disable RSS 14 93

101 POSTAL CODE SYMBOLOGIES RSS Limited To enable or disable RSS Limited, scan the appropriate bar code below. Enable RSS Limited Disable RSS Limited RSS Expanded To enable or disable RSS Expanded, scan the appropriate bar code below. Enable RSS Expanded Disable RSS Expanded 94

102 POSTAL CODE SYMBOLOGIES Dutch Postal To enable or disable Dutch Postal, scan the appropriate bar code below. Enable Dutch Postal Disable Dutch Postal Australian Postal To enable or disable Australian Postal, scan the appropriate bar code below. Enable Australian Postal Disable Australian Postal 95

103 COMPOSITE SYMBOLOGIES Composite CC-C Scan a bar code below to enable or disable Composite bar codes of type CC-C. Enable CC-C Disable CC-C Composite CC-A/B Scan a bar code below to enable or disable Composite bar codes of type CC-A/B. Enable CC-A/B Disable CC-A/B Composite TLC-39 Scan a bar code below to enable or disable Composite bar codes of type TLC-39. Enable TLC-39 Disable TLC-39 96

104 2D SYMBOLOGIES PDF417 To enable or disable PDF417, scan the appropriate bar code below. Enable PDF417 Disable PDF417 MicroPDF417 To enable or disable MicroPDF417, scan the appropriate bar code below. Enable MicroPDF417 Disable MicroPDF417 97

105 2D SYMBOLOGIES Data Matrix To enable or disable Data Matrix, scan the appropriate bar code below. Enable Data Matrix Disable Data Matrix Maxicode To enable or disable Maxicode, scan the appropriate bar code below. Enable Maxicode Disable Maxicode 98

106 2D SYMBOLOGIES QR Code To enable or disable QR Code, scan the appropriate bar code below. Enable QR Code Disable QR Code 99

107 SAMPLE BAR CODES 2D Bar Codes Data Matrix Maxicode QR Code PDF417 MicroPDF

108 SAMPLE BAR CODES 1D Bar Codes EAN-13 EAN-8 UPC-A UPC-E Interleave 2 of 5 Code 39 Code 128 EAN

109 SAMPLE BAR CODES Codabar MSI RSS Limited 102