FR Series Heat Exchanger Unit Heater

Transcription

1 FR Series Heat Exchanger Unit Heater FR Unit Heaters are extra heavy duty (including heavy gauge steel construction) to meet the most demanding service and long life requirements for rugged industrial applications. The FR Series heaters are specifically designed for steam applications that may be subject to freezing conditions, and are of particular value for outdoor applications. Explosion-proof models suitable for hazardous locations are available on custom order. Engineered for ease of maintenance, all parts are easily removed. All fasteners are plated capscrews; no sheet metal screws are used. Heat exchanger cores are of steel construction with tension wound, close fitting aluminium fins. They are resistant to corrosive agents (including hydrogen sulfide). All units are equipped with a narrow-gap, epoxy coated fan guard. Choose from several optional UL listed and/or CSA approved motors with various voltages, phases and frequencies. All FR models have Canadian CRN approvals and are CSA certified for hazardous locations: Class I, Division 1 & 2, Groups C & D; Class II, Division 1 & 2, Groups E, F, & G; Class III, Division 1 & 2; Temperature Code T3B 329 F (165 C) on applicable models only. Epoxy coated 14-gauge steel cabinet construction connections allow for easy core removal. Optional: 2" (50 mm) 300# Flanges* or 2" NPT Male Connections* Choose from several types of motor, general purpose or explosion proof. UL listed and/or CSA approved. 50 or 60 Hz motors. Tension wound close fitting aluminium finned tubes Heresite is a registered trademark of Heresite Protective Coatings Inc. *2" 300# Flanges and 2" NPT Male Connections increase difficulty in core removal. Figure 29 Full-enclosure fan guard featuring narrow spacing FR Series Unit Heater 63

2 Model Coding FR A1 - A1-1A - D Model Series 12 12" 16 16" 20 20" Model & Size Fan Size 24 24" 30 30" 36 36" A Epoxy powder coated carbon steel B Heresite phenolic coated carbon steel Fan Size 1 Pass FR1 FR1 12 THRU FR1 36 C Stainless steel Exchanger Coatings 1 Heat resistant aluminum paint 2 Heresite phenolic coating Heater Certifi cation 1 purpose 2 Explosion proof, Groups C, D, E, F, & G Connections A 3 CSA certifed heater 1 5/8" (16 mm) diameter x 0.065" (1.7 mm) steel tubes Tension wound aluminum fi ns at 10 fi ns/inch Rows: 3 B 2" NPT Male, SCH. 80 C 2" 300# RF Flange Built-in Disconnect Switch Motor Electrical Specifi cations V Phase Hz A B C D E F G H I J K Unit Heater FR Series NOTEe utilizes Doerr/Emerson/Baldor as our standard motor. Specifying any other O.E.M. motor may result in longer lead times. All heat exchangers are registered to C.R.N. OH C. They are approved for use in all provinces and territories in Canada. Heresite coated exchangers and cabinets: contact factory for quote. Louvres and fan blades are also Heresite coated. Contact factory for shipping lead time. Motor designed to be used at rated voltage with tolerances of ±15%. Motor may be marked 230V, but is suitable for 208V operation phase motors are only certifi ed for groups D, F & G. Built in Disconnect only available with CSA certifi ed heaters. Not available on 36 units. 64

3 FR Single Pass The FR Series is designed for steam applications that may be subject to freezing conditions. Maximum operating pressure is to. This heater is of particular value for outdoor applications, such as on drilling rigs, where boiler failure or crew neglect may result in an accidental freeze-up of the heating system. If accidental freeze-up occurs it is highly recommended the heater be returned to Thermon Heating Systems for inspection. Figure 31 Optional Built-in Disconnect Available Figure 30 The fluid flow is divided among all tubes. This is best suited to steam and high flow rate liquid applications. The Disconnect Switch is engineered for use in the most demanding applications such as drilling rigs, utilidors and compression stations where high vibration, dirt, moisture, fluctuating power and high impact conditions exist. The built-in disconnect switch is available on all FR heaters. Table 34 Performance Data for FR1-12 Entering Steam Refer to the Ruffneck TM HP model for service above 100 psi. For 50 Hz power supply, derate output by 10% FR Series Unit Heater 65

4 Table 35 Performance Data for FR Refer to the Ruffneck TM HP model for service above 100 psi. Above figures are based on calculations at sea level and are intended as reference material only. Results may vary due to customer applications. Table 36 Performance Data for FR Unit Heater FR Series Refer to the Ruffneck TM HP model for service above 100 psi. For 50 Hz power supply, derate output by 10%

5 Table 37 Performance Data for FR Refer to the Ruffneck TM HP model for service above 100 psi. Above figures are based on calculations at sea level and are intended as reference material only. Results may vary due to customer applications. Table 38 Performance Data for FR Refer to the HP model for service above 100 psi. For 50 Hz power supply, derate output by 10%. FR Series Unit Heater 67

6 Table 39 Performance Data for FR Refer to the HP model for service above 100 psi. Above figures are based on calculations at sea level and are intended as reference material only. Results may vary due to customer applications Unit Heater FR Series 68

7 Specifications FR CFM 1147 FPM psi stream Propeller Fan 3 Wing Aluminum, 12 (305 mm) Dia. 5/8 (16 mm) Bore Motor Requirements 1/2 HP, 1725 RPM, Frame 56 1/4 (6 mm) probe will not enter. 5/8 (16 mm) NC Tap - 2 holes (2 mm) steel Net Weight 75 lbs (34 kg) * Shipping Weight 102 lbs (46.3 kg) * Figure 32 Add 12 lbs (5.4 kg) to flange units * Add 15 lbs (6.8 kg) to disconnect units FR1-16 Figure 33 * At 70 F (21 C) at sea level Add 12 lbs (5.4 kg) to flange units * Add 15 lbs (6.8 kg) to disconnect units Number of Tubes 13 Number of Rows 2 Max. Operating Temp. 80 psi for CSA Certified Steam Heaters 650 F (343 C) 1588 CFM 1069 FPM psi stream Propeller Fan 3 Wing Aluminum, 16" (406 mm) Dia. 5/8" (16 mm) Bore Motor Requirements 1/2 HP, 1725 RPM, Frame 56 1/4" (6 mm) probe will not enter " (2 mm) steel Net Weight 109 lbs (49.4 kg) * Shipping Weight 137 lbs (62.1 kg) * Number of Tubes 17 Number of Rows 2 FR Series Unit Heater 69

8 Max. Operating Temp. 572 F (300 C) FR CFM 1153 FPM psi stream Propeller Fan 3 Wing Aluminum, 20" (508 mm) Dia. 5/8" (16 mm) Bore Motor Requirements 1/2 HP, 1725 RPM, Frame 56 1/4" (6 mm) probe will not enter " (2 mm) steel Net Weight 138 lbs (62.6 kg) * Shipping Weight 161 lbs (73 kg) * Figure 34 Add 12 lbs (5.4 kg) to flange units * Add 15 lbs (6.8 kg) to disconnect units. FR1-24 Number of Tubes 21 Number of Rows 2 Max. Operating Temp. 650 F (343 C) Unit Heater FR Series * At 70 F (21 C) at sea level Figure 35 Add 12 lbs (5.4 kg) to flange units * Add 15 lbs (6.8 kg) to disconnect units 3405 CFM 981 FPM psi stream Propeller Fan 3 Wing Aluminum, 24" (610 mm) Dia. 5/8" (16 mm) Bore Motor Requirements 1/2 HP, 1725 RPM, Frame 56 7/16" (11 mm) probe will not enter " (2 mm) steel Net Weight 191 lbs (86.6 kg) * Shipping Weight 224 lbs (101.6 kg) * Number of Tubes 38 Number of Rows 3 Max. Operating Temp. 100 psi for CSA Certified Steam Heaters 650 F (343 C) 70

9 FR1-30 Figure 36 Add 12 lbs (5.4 kg) to flange units * Add 15 lbs (6.8 kg) to disconnect units 4569 CFM 814 FPM psi stream Propeller Fan 3 Wing Aluminum, 30" (762 mm) Dia. 5/8" (16 mm) Bore Motor Requirements 3/4 HP, 1140 RPM, Frame 56 7/16" (11 mm) probe will not enter " (2 mm) steel Net Weight 286 lbs (121.6 kg) * Shipping Weight 345 lbs (156.5 kg) * Number of Tubes 47 Number of Rows 3 Max. Operating Temp. 80 psi for CSA Certified Steam Heaters 650 F (343 C) FR1-36 Figure 37 Add 12 lbs (5.4 kg) to flange units * Add 15 lbs (6.8 kg) to disconnect units. Propeller Fan 7830 CFM 852 FPM psi stream 6 Wing Aluminum, 36" (914 mm) Dia. 1" (25mm) Bore Motor Requirements 1½ HP, 1725 RPM, Frame 56 Drive Pulley Driven Pulley Drive Belt Fan Speed B3.6" B9.9" B42 V-Belt 627 RPM Steel, Powder Coated Epoxy, 1/2" (13 mm) gap 0.105" (2.66 mm) steel Net Weight 534 lbs (242.2 kg) * Shipping Weight 597 lbs (270.8 kg) * Number of Tubes 59 Number of Rows 3 Max. Operating Temp. 85 psi for CSA Certified Steam Heaters 650 F (343 C) FR Series Unit Heater 71