Type. Listings: The luminaire shall be NRTL certified to UL 1598 and 8750 standards for use in wet locations.

Transcription

1 VIPER S + L Cat.# Type Job design. per formance. technology pprovals LUMINIRE POLE COMO LUMINIRE ND POLE PRODUCT IMGE(S) SPECIFICTIONS The eacon Viper luminaire is available in two sizes with a wide choice of different LED Wattage configurations and optical distributions designed to replace HID lighting up to 000W MH or HPS. Luminaires are suitable for wet locations. Construction: One piece optical cartridge system consisting of an LED engine, LED lamps, optics, gasket and stainless steel bezel. Cartridge is held together with internal brass standoffs soldered to the board so that it can be field replaced as a one piece optical system. Two-piece silicone and micro-cellular polyurethane foam gasket ensures a weather-proof seal around each individual LED. LED/Optics: LED driver accepts 00V through 277V, 50 Hz to 60 Hz (UNV). Power factor is.92 at full load. ll electrical components are rated at 50,000 hours at full load and 25 C ambient conditions per MIL- 27F Notice 2. Dimming drivers are standard. Component-to-component wiring within the luminaire may carry no more than 80% of rated load and is listed by UL for use at 600VC at 50 C or higher. Plug disconnects are listed by UL for use at 600 VC, 3 or higher. 3 rating applies to primary (C) side only. Electrical: Fixture electrical compartment shall contain all LED driver components and shall be provided with a push-button terminal block for C power connections. Surge protection - 20K; shuts off at end of life. Lifeshield Circuit - protects luminaire from excessive temperature by interfacing with the 0-0V dimmable drivers to reduce drive current as necessary. The factory- preset temperature limits are designed to ensure maximum hours of operation to assure L70 rated lumen maintenance. The device shall activate at a specific, factory-preset temperature, and progressively reduce power over a finite temperature range. luminaire equipped with the device may be reliably operated in any ambient temperature up to 55ºC (3ºF). The thermal circuit will allow higher maximum Wattages than would be permissible on an unregulated luminaire (if some variation in light output is permissible), without risk of premature LED failure or lumen depreciation. Operation shall be smooth and undetectable to the eye. Thermal circuit is designed to fail on, allowing the luminaire to revert to full power in the event of an interruption of its power supply, or faulty wiring connection to the drivers. The device shall be able to co-exist with other 0-0V control devices (occupancy sensors, external dimmers, etc.). The device will effectively control the solder point temperature as needed; otherwise it will allow the other control device(s) to function unimpeded. rectangular arm MOUNTING Side View ack View R Rectangular rm DIMENSIONS - SMLL 4 /8 C Intended Use: Installation: Mounting options for horizontal arm. Mounting hardware included. Product is suitable for applications requiring 3G testing prescribed by NSI C36.3 Finish: Dark ronze (textured) eacote V polyester powder-coat electro-statically applied and thermocured. eacote V finish consists of a five stage pretreatment regimen with a polymer primer sealer and top coated with a thermoset super TGIC polyester powder coat finish. The finish meets the M performance specification which includes passing a 3000 hour salt spray test for corrosion resistance and resists cracking or loss of adhesion per STM D522 and resists surface impacts of up to 60 inch-pounds. Listings: The luminaire shall be NRTL certified to UL 598 and 8750 standards for use in wet locations. Front EP.67 ft2 C Weight: lbs 6.75 (6.8 kg) (425 mm) (286 mm) (578 mm) DIMENSIONS - LRGE D SE COVER Front nchor ase Detail Straight Square and Tapered Poles Round Straight and Tapered Poles (ll excluding RT Group (RT Group & & RTS RTS Group 2) 80 2) D Weight: C Group 80 olt Slots/Holes nchor olt olt Slots/Holes olt inolt Circle olt Circle 25.0 lbs nchor 29.2 Location24.9 Location in Relation Relation rm 2 rm mm) rm 2mm) rm (.3 kg) (05 mm) (362 (704 mm)to Shaft (64 to Shaft Rotation Rotation EP.0 ft2 0'-30' olt Square Height olt Square POLE CP nchor olt Hex Nut Flat Washer nchor ase Detail ase Plate Warranty: Five year limited warranty (for more information visit: warranty). 80 Flat Washer Hex rm 2 Nut 80 olt Projection olt Slots/Holes olt Slots/Holes olt Circle olt Circle rm rm 2 Grout with drain 8" Optional olt Square Level Foundation rm Engineering of olt Square footing by others *SSS- pole specifications continued on page 2. olt Square (Outer) Height 6' - 25' SE COVER olt Square (Inner) 0 olt Circle (Outer) CERTIFICTIONS/LISTINGS SE COVER Small Single Head Viper Configurations paired with 25 poles include 270 olt Circle (Inner) 80 2 VM2 - VIRTION DMPER 2ND MODE Height 0'-30' Factory installed, internal damper designed to alter pole resonance to reduce movement and material fatigue caused by 2nd mode vibration. VIRTION DMPER 2ND MODE 3T 2L TENON MOUNTING ORIENTTION SINGLE 8" 2 8" 2L 3Y 42 O 3T 2L 80 3Y location4 Denotes handhole 3T eacon Products th venue Circle East radenton, FL Phone: design. per formance. technology 205 ECON PRODUCTS, ll Rights Reserved For more information visit our website: Printed in US VPS-SPEC 6/4 Height of option in feet olt Square (Outer) 3Y 4 Denotes handhole location

2 SPECIFICTIONS continued SSS- POLE PPLICTIONS Lighting installations for side mounting of luminaires with effective projected area (EP) not exceeding maximum allowable loading of the specified pole in its installed geographic location CONSTRUCTION SHFT: One-piece straight steel with square cross section, flat sides and minimum radius on all corners; Minimum yield of 46,000 psi (STM-500, Grade ); Longitudinal weld seam to appear flush with shaft side wall; Steel base plate with axial bolt circle slots welded flush to pole shaft having minimum yield of 36,000 psi (STM 36) SE COVER: Two-piece square aluminum base cover included standard POLE CP: Pole shaft supplied with removable cover when applicable; Tenon and post-top configurations also available HND HOLE: Rectangular 3x5 steel hand hole frame (2.38 x 4.38 opening); Mounting provisions for grounding lug located behind gasketed cover NCHOR OLTS: Four galvanized anchor bolts provided per pole with minimum yield of 55,000 psi (STM F554). Galvanized hardware with two washers and two nuts per bolt for leveling FINISH Dark ronze (textured) TGIC thermoset polyester powder coat paint finish with nominal 3.0 mil thickness Powder paint prime applied over white metal steel substrate cleaned via mechanical shot blast method Decorative finish coat available in seven standard colors; Custom colors available; RL number preferable; Internal protective coating available ORDERING INFORMTION Ordering Logic* - ll Configurations Dark ronze Finish (textured) PRODUCT VS PRODUCT VL LUMENS 9 9K Nominal (VPS-36N-80) 2 2K Nominal (VPS-48N-0) 5 5K Nominal (VPS-60N-36) LUMENS 20 20K Nominal (VPL-80N-80) 29 29K Nominal (VPL-96N-280) LED CCT N 4000K C 5000K SINGLE OR DOULE HED DEG. - Single Head 2X Double Deg. DISTRIUTION T3 Type 3 T4 Type 4 POLE S6 6 Square S20 2 Square S25 25 Square NCHOR OLTS - With nchor olts/template L Less nchor olts/template *25 piece max order size for 0-day shipment. CCESSORIES - Order Separately Catalog Number Description T30M38 3/4 x 30 x 3 anchor bolt set (four individual bolts) SSS- Series pole anchor bolt template Select configurations include a vibration damper. Refer to the Pronto Combo wind loading table for details. eacon Products th venue Circle East radenton, FL Phone: ECON PRODUCTS, ll Rights Reserved For more information visit our website: Printed in US VPS-SPEC 6/4

3 PHOTOMETRICS VPS-36N-80-4K-T3 vs. 75 MH (horizontal lamp) VPS-36N-80-4K-T4 vs. 75 MH (horizontal lamp) 6 VPS-48N-0-4K-T3 vs. 250 MH (horizontal lamp) 6 6 VPS-48N-0-4K-T4 vs. 250 MH (horizontal lamp) Mounting Height 6 Mounting Height 20 Mounting Height 20 Mounting Height VPL-60N-36-4K-T3 VPL-60N-36-4K-T4 VPL-80N-80-4K-T3 VPL-80N-80-4K-T4 25 Mounting Height 25 Mounting Height 25 Mounting Height 25 Mounting Height VPL-96N-280-4K-T3 vs. 000 MH (vertical lamp) VPL-96N-280-4K-T4 vs. 000 MH (vertical lamp) 25 Mounting Height 25 Mounting Height HID LED 0.5 Foot-candles 0.5 Foot-candles eacon Products th venue Circle East radenton, FL Phone: ECON PRODUCTS, ll Rights Reserved For more information visit our website: Printed in US VPS-SPEC 6/4

4 PERFORMNCE DT VIPER SMLL CONFIGURTIONS 5K (5000K nominal, 70 CRI) 4K (4000K nominal, 70 CRI) # LED S (MILLIMPS) SYSTEM WTTS DISTRIUTION TYPE LUMENS LPW U G LUMENS LPW U G m 80W T T m 0W T T m 36W T T VIPER LRGE CONFIGURTIONS 5K (5000K nominal, 70 CRI) 4K (4000K nominal, 70 CRI) # LED S (MILLIMPS) SYSTEM WTTS DISTRIUTION TYPE LUMENS LPW U G LUMENS LPW U G m 80W T T m 280W T T Lumen values are from photometric tests performed in accordance with IESN LM Data is considered to be representative of the configurations shown. ctual performance may differ as a result of end-user environment and application. ELECTRICL DT - SMLL VIPER LUMINIRE # OF LEDS NUMER OF RS (m) m m ELECTRICL DT - LRGE VIPER LUMINIRE # OF LEDS NUMER OF RS (m) INPUT VOLTGE (V) SYSTEM POWER (w) (mps) INPUT VOLTGE (V) SYSTEM POWER (w) (mps) PROJECTED LUMEN MINTENNCE MIENT TEMP. 0 25,000 50,000 TM-2-60,000 00,000 Calculated L70 (HOURS) 25 C / 77 C >470,000 Projected per IESN TM-2- Data references the extrapolated performance projections for the base model in a 40 C ambient, based on 0,000 hours of LED testing per IESN LM MIENT TEMPERTURE LUMEN MULTIPLIER 0 C 32 F.02 0 C 50 F.0 20 C 68 F C 77 F C 86 F C 04 F 0.98 Use these factors to determine relative lumen output for average ambient temperatures from 0-40 C (32-04 F). DRILL PTTERN 4 Suggested distance of pole 2.50 Ø5/8 2X Ø5/6 Rectangular rm Ø4 Pole Ø5 Pole Ø6 Pole EP VIPER LRGE Config. EP VIPER SMLL Config. EP eacon Products th venue Circle East radenton, FL Phone: ECON PRODUCTS, ll Rights Reserved For more information visit our website: Printed in US VPS-SPEC 6/4

5 SCE7-05 WIND MP FLORID REGION WIND MP Standard SCE7-05 Wind Map 85 MPH Zone MPH Zone 00 MPH Zone 05 MPH Zone (HI) 0 MPH Zone 20 MPH Zone 45 MPH Zone (PR) Pole Height (4 Sq x 0.25 wall thickness) llowable EPs (ft/sq) NR Viper Sm - Single NR Viper Sm - 80 NR NR NR Viper Lg - Single NR NR Viper Lg - 80 NR NR NR Florida Region Wind Map (200 uilding Code) 5 MPH Zone 20 MPH Zone MPH Zone 40 MPH Zone 50 MPH Zone 60 MPH Zone 70 MPH Zone 80 MPH Zone Pole Height (4 Sq x 0.25 wall thickness) llowable EPs (ft/sq) NR NR NR Viper Sm - Single NR NR NR Viper Sm - 80 NR NR NR NR Viper Lg - Single NR NR NR Viper Lg - 80 NR NR NR NR NR Florida uilding Code utilizes a different calculation method than SCE, which results in different allowable EPs. Consult your local authorities to determine which standard to use for your project cceptable Includes Vibration Damper Not Recommended Notes: Pole used in program includes a vibration damper (VM2 style) due to low luminaire EP and 25 mounting height. *Consult the complete list of pole notes on the pole specification sheets located on the Hubbell Lighting web site. SCE7-05 WIND MP Wind M United States and Ca Special Wind Region (Consult Local uthorities) HWII 05 mph PUERTO RICO 45 mph NOTES: 40 Values are based on 50 year mean recurrence interval 3 50 above grade. Hawaii has an 05 mph wind velocity. Puerto Rico has a 25 mph wind velocity. FLORID REGION WIND MP (200 FLORID UILDING CODE) Caution must be exercised in determining wind velocities in special wind areas such as: Mountainous Regions 5 20 reas surrounding the Great Lakes or other large bodies of water or open land. Florida region wind map above is based reas subject upon 3-second to extreme wind conditions, such as hurricanes, typhoons, cyclones, and tornadoes. gust winds and the 200 Florida uilding Code reas adjacent to airports. ny specific area with a known or suspected abnormally high intermittent wind condition caused by geography, adjacent structures, or other specific local conditions that may not be recorded in National Weather Service records. llowable pole EP for jobsite wind conditions must be eacon Products th venue equal Circle to or East greater radenton, than fixture FL EP Responsibility Phone: lies with the specifier for correct pole selection based on SHTO wind map and job location. 205 ECON PRODUCTS, ll Rights Reserved For more information visit our website: Printed in US VPS-SPEC 6/4 The Wind Map is intended only as a general guide. lw consult local authorities to determine maximum wind velocities, gusting and unique wind conditions for each specific application. 40 CUTION: Wind speeds and listed EPs are for groun mounted installations. 50 Poles mounted on structures (suc as 40 bridges and buildings) must consider vibration and coefficient of height 60 factors beyond this general guide. Consult 50 SHTO standards. 70 Extreme Wind Events: Hurricanes, Typhoons, Cyclones Tornadoes expose poles to flying debris, wind shear, an 60 other unpredictable aerodynamic forces not indicated b the wind 70 velocity ratings. 80 lighting Poles 80 installed as recommended, undamaged b Pole Strength Limited Warranty: Standard, unmodified corrosion, or lack of maintenance, shall withstand stead wind conditions as provided on page 2 (llowable Pol EP). Installation of poles without luminaires, or attach of any unauthorized accessories to poles shall void this warranty.