SSS SERIES POLES SQUARE STRAIGHT STEEL
|
|
- Oscar Lee
- 6 years ago
- Views:
Transcription
1 SSS SERIES POLES SQUARE STRAIGHT STEEL Cat.# Job Approvals APPLICATIONS Lighting installations for side and top mounting of luminaires with effective projected area (EPA) not exceeding maximum allowable loading of the specified pole in its installed geographic location. FEATURES SHAFT: One-piece straight steel with square cross section, flat sides and minimum 0.36 radius on all corners. Minimum yield of 46,000 psi (ASTM-A500, Grade B). Longitudinal weld seam to appear flush with shaft side wall. Steel base plate with axial bolt circle slots welded flush to pole shaft having minimum yield of 36,000 psi (ATM-A36). BASE COVER: Two-piece square aluminum base cover included standard. POLE CAP: Pole shaft covered with removable non-metallic cover when applicable. Tenon and post-top configurations also available. HAND HOLE: Rectangular steel-reinforced hand hole (2.5 x 4.5 ). Pole grounding lug located behind gasketed cover. ANCHOR BOLTS: Four galvanized anchor bolts provided per pole with minimum yield of 55,000 psi (modified ASTM-A36). Galvanized hardware with two washers/nuts per bolt for leveling meet or exceed bolt strength. FINISH: Durable Lektrocote TGIC thermoset polyester powder coat paint finish with nominal 3.0 mil thickness. Zinc-rich powder paint prime applied over white metal steel substrate cleaned via mechanical shot blast method. Decorative finish coat available in seven standard colors. Custom colors available. RAL number preferable. Internal protective coating available. Nominal Height Handhole 12" BASE DETAIL Anchor Rod Hex Nut Plain Washer Base Plate Grout Finish Grade Plain Washer Hex Nut Grout after pole is set and plumbed Foundation Level Bolt Projection Engineering of footing by others 20 AMP GFCI RECEPTACLE & COVER COVER GASKET 21 GASKET 1/4 FILLET WELD ALL AROUND. SEE NOTE Q18 OPTION Bolt Square Bolt Circle and Tapered Poles Anchor Bolt Location in Relation to Shaft Rotation Handhole 2015 SPAULDING LIGHTING, All Rights Reserved For more information visit our website: Printed in USA SSSPOLES-SPEC 1/15
2 ORDERING INFORMATION S - S - S TA - DB Cross Section Style Material Nominal Length Nominal Shaft Dia. Shaft Thickness Mounting Finish Pole Ht. Nominal Wind Load Rating 1 Bolt Pole Shaft Wall Circle Bolt Circle Bolt Sq. Base Plate Anchor Bolt Bolt Wt ft m Dim. MPH MPH MPH MPH MPH Thick. (Sug.) (sq.) Size Proj. (lbs) SSS XX-XX " " 11" 8-11" " x 0.75" 3/4 x x 3" 4" 91 SSS XX-XX " " 11" " " 12 x 1" 3/4 x x 3" 4" 106 SSS XX-XX " " 11" 8-11" " x 0.75" 3/4 x x 3" 4" 104 SSS XX-XX " " 11" " " 12 x 1" 3/4 x x 3" 4" 122 SSS XX-XX " " 11" 8-11" " x 0.75" 3/4 x x 3" 4" 116 SSS XX-XX " " 11" 8 1/2-12" 6-8.4" 11 x 1" 3/4 x x 3" 4" 158 SSS XX-XX " " 11" " " 12 x 1" 3/4 x x 3" 4" 138 SSS XX-XX " " 11" 8-11" " x 0.75" 3/4 x x 3" 4" 128 SSS XX-XX " " 11" 8 1/2-12" 6-8.4" 11 x 1" 3/4 x x 3" 4" 176 SSS XX-XX " " 11" " " 12 x 1" 3/4 x x 3" 4" 153 SSS XX-XX " " 11" " " 12 x 1" 3/4 x x 3" 4" 214 SSS XX-XX " " 11" 8 1/ " x 0.75" 3/4 x x 3" 4" 147 SSS XX-XX " " 11" " " 11 x 1" 3/4 x x 3" 4" 201 SSS XX-XX " " 11" " " 12 x 1" 3/4 x x 3" 4" 175 SSS XX-XX " " 11" " 12 x 1" 3/4 x x 3" 4" 243 SSS XX-XX " " 11" 8-11" " x 0.75" 3/4 x x 3" 4" 160 SSS XX-XX " " 11" 8 1/2-12" 6-8.4" 11 x 1" 3/4 x x 3" 4" 225 SSS XX-XX " " 11" " " 12 x 1" 3/4 x x 3" 4" 191 SSS XX-XX " " 11" " " 12 x 1" 3/4 x x 3" 4" 266 SSS XX-XX " " 12" " " 12 x 1" 1 x 36 x 4" 4" 312 SSS XX-XX " NR NR.119" 11" 8-11" " x 0.75" 3/4 x x 3" 4" 190 SSS XX-XX " " 11" " 6-8.4" 11 x 1" 3/4 x x 3" 4" 266 SSS XX-XX " NR.119" 11" " " 12 x 1" 1 x 36 x 4" 4" 231 SSS XX-XX " " 11" " " 12 x 1" 1 x 36 x 4" 4" 324 SSS XX-XX " " 11" " " 12 x 1" 1 x 36 x 4" 4" 437 SSS XX-XX " " 12" " " 12 x 1" 1 x 36 x 4" 4" 404 SSS XX-XX " NR.179" 11" " 6-8.4" 11 x 1" 1 x 36 x 4" 4" 290 SSS XX-XX 9.1 4" NR.179" 11" " 6-8.4" 11 x 1" 1 x 36 x 4" 4" 313 SSS XX-XX 9.1 5" NR.179" 11" " " 12 x 1" 1 x 36 x 4" 4" 398 SSS XX-XX 9.1 5" " 11" " " 12 x 1" 1 x 36 x 4" 4" 537 SSS XX-XX 9.1 6" " 12" " " 12 x 1" 1 x 36 x 4" 4" 467 SSS XX-XX 9.1 6" " 12" " " 12 x 1" 1.25 x 42 x 6" 4" 6 SSS XX-XX " NR.179" 12" " " 12 x 1" 1 x 36 x 4" 4" 538 SSS XX-XX " " 12" " " 12 x 1" 1.25 x 42 x 6" 4" 726 SSS XX-XX " NR NR NR.179" 12" " " 12 x 1" 1 x 36 x 4" 4" 614 SSS XX-XX " NR.250" 12" " " 12 x 1" 1.25 x 42 x 6" 4" Allowable EPA with 1.3 gust factor. To determine max. pole loading weight, multiply allowable EPA by lbs. NOTE Factory supplied template must be used when setting anchor bolts. Hubbell Lighting will deny any claim for incorrect anchorage placement resulting from failure to use factory supplied template and anchor bolts. COMPLETE PART NUMBER REQUIRES SHAFT ABOVE PLUS MOUNTING TYPE, FINISH & APPROPRIATE OPTIONS BELOW MOUNTING TYPE FINISH OPTIONS AX 1 Side - Single DB Dark Bronze Q55 Internal Coating (Hubbell Seal) BX 1 Side - Double at 90 BL Black Q Amp GFCI Receptacle CX 1 Side - Double at 180 WH White and Cover DX 1 Side - Triple at 90 GR Gray Q22 3 Extra Handhole FX 1 Side - Quad at 90 PS Platinum Silver Q Coupling P1 Pad Mount - Spider RD Red (Premium Color) Q Coupling P2 Pad Mount - Yoke FG Forest Green (Premium Color) Q 3 2 Coupling P3 Pad Mount - Yoke CC Custom Color (Consult Factory) Q32 3 Mid-pole Luminaire Bracket (Proformer XL only) PR Primer Only Q41 1st mode vibration damper TA Tenon (2.375 OD) Q42 2nd mode vibration damper TB Tenon (2.875 OD) 1 DRILL PATTERNS: Replace X with LAB Less Anchor Bolts TR 2 1 = Spaulding luminaires with a straight pole (4-bolt), Removable Tenon CSA CSA Certified (consult factory) 2 = Cimarron CR1, MSV and Raven Series luminaires. (2.375 x 4.25) 4 = MSS & DS luminaires, CD Concord Luminaire 5 = Spaulding Detroit III luminaires, 6 = DM luminaires OT No drilling (includes pole cap) 2 Removable tenon used in conjunction with side arm mounting. First specify desired arm configuration followed by the TR notation. Example: SSS C6-TR-DB A B C D E F 3 Specify option location using logic found on cover. Denotes handhole location OPTION ORIENTATION Follow the logic below when ordering location specific options. For each option, include its orientation (in degrees) and its height (in feet). Example: Option Q26 should be ordered as: SSS TA-DB-Q (.5 coupling on the handhole/arm side of pole, 15 feet up from the pole base) 1 spacing required between option. Consult factory for other configurations. Height of option (in feet) SPAULDING LIGHTING, All Rights Reserved For more information visit our website: Printed in USA SSSPOLES-SPEC 1/15 0 Hand hole at 0 orientation
3 CIMARRON LED Cat.# Job Approvals SPECIFICATIONS Construction: Stylish vertically finned die-cast solid top housing for maximum heat dissipation; Stops collection of unsightly debris from gathering on top of the housing Rugged lower die-cast aluminum heat sink accelerates thermal management and optimizes PCB and optical performance Separate optical and electrical compartment for optimum component operation One piece die cut silicone gasket ensures weather proof seal around each individual LED for IP65 rating Backlight Control (BC) option available for 85% spill light reduction, doesn t change fixture appearance or EPA, recommended for III and IV distributions Stamped bezel provides mechanical compression to seal the optical assembly Complements the Hubbell Southwest series of outdoor fixtures Weight pounds, EPA ft 2 Suitable for applications requiring 3G testing prescribed by ANSI C Optics: Choice of 72 high brightness LED configurations with individual acrylic lenses specially designed for IES II, III, IV and V distributions Auto optics designed for front row 1A and interior rows 2A (see distribution under ordering and page 2) CCT: 00K (80 CRI), 4000K (70 CRI), 5000K (67 CRI), and turtle friendly Amber LED options CRI: 70 Electrical: Universal input voltage VAC, 50/60 Hz Integral step-down transformer for 347V & 480V Ambient operating temperature -40 C to 40 C Automatic thermal self-protection Drivers have greater than 90% power factor and less than 10% THD Optional continuous dimming to 10% or dual circuitry available CERTIFICATIONS/LISTINGS LED Product Partner LED drivers have output power overvoltage, over-current protection and short circuit protection with auto recovery 1050 ma driver available with 90L configuration for increased lumen output LED electrical assembly, including PR devices, consumes no power in the off state Field replaceable surge protection device provides 20KA and 10KV protection meeting ANSI/IEEE C Category C High and Surge Location Category C3. The SPD is designed with a clamping voltage of 1600V at 20KA using industry standard 8/20µs waveform. Controls: Drivers are 0-10V dimming standard. Photocell, occupancy sensor and wireless controls available for complete on/off and dimming control Lumen maintenance: L90 at 60,000 hours (Projected per IESNA TM-21-11) Installation: Two die-cast aluminum arm designs: The decorative arm offers a sleek upswept look while the straight arm follows the housing s contoured lines for continuity of style Fixture ships with arm installed for ease of installation and mounts to #2 drill pattern Wall bracket, mast arm fitter and pole accessories are also available allowing easy mounting for virtually any application Finish: TGIC thermoset polyester powder paint finish applied at nominal 2.5 mil thickness Warranty: Five year limited warranty (for more information visit: resources/warranty/ Listings: Listed to UL1598 and CSA C22.2# for wet locations Models meet DesignLights Consortium (DLC) qualifications, consult DLC website for more details: IDA approved IP65 PRODUCT IMAGE(S) 90 LED 3/4 VIEW LED DIMENSIONS A B C D E F G 6 3/4" 171mm 60 LED 90 LED A A 21 3/4" 552mm Upswept Arm Straight Arm 16" 406mm B B C 6 5/8" 168mm G E 6 5/16" 160mm F D 5 5/8" 143mm 6 1/8" 155mm ORDERING INFORMATION SEE NEXT PAGE 2015 SPAULDING LIGHTING, All Rights Reserved For more information visit our website: Printed in USA CL1LED-SPEC 4/15
4 ORDERING INFORMATION ORDERING EXAMPLE: CL1-A-90LU-5K-3-DB-RPA3 CL1 SERIES NO. OF LEDS CL1 Cimarron LED 90L 90 High brightness LEDs 60L 60 High brightness LEDs L High brightness LEDs MOUNTING A Arm mount construction (6 straight rigid arm included & acceptable for 90 configurations) AD Decorative arm mount const. (6 decorative upswept arm incl. & acceptable for 90 configurations) VOLTAGE U F E4 120V 208V 240V 3K 4K 5K AM7 277V 480V, 60 Hz 00K mA Amber 5000K Amber (590 nm available for Turtle Friendly applications (consult factory) CCT only ma (use with 90L only for higher lumen output) COLOR DB BL WH GR PS RD DISTRIBUTION 2 II 3 III 4 5M 5S 5W 2L Notes: 1- For BL option 90L and 60L; N/A 347V & 480V 2 - BL & CD cannot be combined 3L 3 - Fuse option not available with universal voltage 4 - Select F3 fusing option for 220V 4L 5 - Photocell receptacle not available with BL option 6 - Recommended for III and IV distributions only 2R 7 - Available in 350mA drive current only IV, 5M V fully adjustable dimming with automatic daylight calibration and 3R different time delay settings, must order minimum of one SCP-REMOTE 4R control to program dimming settings (see accessories) 9-120V/277V/347V/480V only 1A 10- Must specify 120V, 208V, 240V or 277V; not available with PR option; consult factory for 347V and 480V application, not available 1AR with BL or CD options. 1AL 2A 2AR 2AL Leave blank for 700mA (standard) 4000K 220V, 50 Hz IV V Medium OPTIONS DRIVE CURRENT 347V, 60 Hz MAF Mast arm fitter for mounting to standard 2 3/8" mast arm bracket, includes 6" straight rigid arm CCT Universal 120V-277V, 50/60 Hz Dark Bronze Black White Gray Platinum Silver Red (premium color) FG Forest Green V Short (premium color) V Wide CC Custom Color II Rotated 90 left BC BL1,2,5 CD2 WB RPA3 RPA4 RPA5 RPA6 F(X)3,4 6 Backlight control Bi-level control Continuous dimming Wall bracket 3 Round pole adapter 4 Round pole adapter 5 Round pole adapter 6 Round pole adapter Fusing (replace X with voltage: 1-120V, 2-208V, 3-240V, 4-277V, 5-480V, 6-347V) SSB Stainless steel LED bezel VG Vandal guard CONTROL OPTIONS WIR WiSCAPE WIRPC WiSCAPE motion control TCM10 For remote wireless control of Child luminaire on the TOTUS network III Rotated 90 left PR(X)5 NEMA Photo cell receptacle IV Rotated 90 left II Rotated 90 right III Rotated 90 right SCP8,9 IV Rotated 90 right Auto Front Row I Controls Guide Auto Front Row I Rotated 90 right SCPW8,9 Auto Front Row I Rotated 90 left Auto Front Row II Auto Front Row II Rotated 90 right Auto Front Row II Rotated 90 left (replace X with voltage: U= , 5=480, 6 =347) Programmable motion control, designed for ' to 40' mounting heights, factory default is 10% light level in unoccupied state (reference coverage area on pg. 3) Programmable motion control, designed for up to 40' mounting heights for widest coverage, factory default is 10% light level in unoccupied state (reference coverage area on page 3) ENERGY SAVING DATA ENERGY DATA Power Factor Total Harmonic Distortion >.9 <10% LIGHT INPUT WATTS ENGINE 120V-277V 347V-480V L-5K L-5K L-5K L-5K L-4K L-4K 90L-4K L-4K L-3K L-3K L-3K L-3K TYPE AUTOMOTIVE DEALERSHIP OPTICS For Automotive Dealership applications Spaulding Lighting has developed two optics designed for enhanced and proper lighting of the auto dealership merchandise and the front row 1A and interior rows 2A (See CL1 distribution information for details) TYPE LUMENS DELIVERED TYPE 4 TYPE 5M TYPE 5S TYPE 5W A - Front Row Auto Optic DRIVERS CURRENT 2@700mA 4@700mA 6@700mA 6@1050mA 2@700mA 4@700mA 6@700mA 6@1050mA 2@700mA 4@700mA 6@700mA 6@1050mA 2A - Drive Lane Auto Optic Optic 1A Maximum illumination on front row display Maximum pole spacing Optic 2A Excellent front row illumination and drive lane Optimal uniformity for drive lane and interior rows ACCESSORIES SEE NEXT PAGE 2015 SPAULDING LIGHTING, All Rights Reserved For more information visit our website: Printed in USA CL1LED-SPEC 4/15
5 ACCESSORIES SCP-REMOTE 9 Remote control for SCP option. Order at least one per project to program and control. CR-RPA3-XX 1 Round pole adapter for straight arm ( ) CR-RPA4-XX 1 Round pole adapter for straight arm ( ) CR-RPA5-XX 1 Round pole adapter for straight arm (5 ) CR-RPA6-XX 1 Round pole adapter for straight arm (6 ) CRD-RPA2-XX 1 Round pole adapter for upswept arm ( ) CRD-RPA3-XX 1 Round pole adapter for upswept arm ( ) CRD-RPA4-XX 1 Round pole adapter for upswept arm ( ) CRD-RPA5-XX 1 Round pole adapter for upswept arm (5 ) CRD-RPA6-XX 1 Round pole adapter for upswept arm (6 ) WB-CR-XX 1 Wall bracket TPLB-XX 1 Twin parallel luminaire bracket MAF-CL-XX 3 Horizontal mast arm fitter for 2 3/8 OD arm. Mounts to standard 6 arm (ordered with fixture) 1 Replace XX with color choice, eg.: DB for Dark Bronze 2 When ordering poles, specify Pole Drill Pattern #2 3 Fixture must include standard 6 arm MOUNTING ACCESSORIES ARM-CL-K-TA-XX 1 ARM-CL-TK-TA-XX 1 ARM-CL-K-S-XX 1 1 Replace XX with color choice, eg.: DB for Dark Bronze 2 Fixture must include standard 6 straight arm Adjustable mounting arm for single fixture (2-3/8 tenon) 5 lbs. 2.3 kgs. Adjustable mounting arm for two fixtures at 180 (2-3/8 tenon) 7 lbs. 3.2 kgs. 10 adjustable arm.5 lbs..05 kgs lbs. 2.6 kgs. ARM-CL-K-TA-XX ARM-CL-TK-TA-XX TENON TOP POLE BRACKET ACCESSORIES MAL-TK-X (2 3/8 OD tenon) (RSS version requires 4 round pole adapter) SETA-XX 1 Square pole tenon adapter (4 at 90 degrees) RETA-XX 1 Round pole tenon adapter (4 at 90 degrees) TETA-XX 1 Hexagonal pole tenon adapter (3 at 120 degrees) 1 Replace XX with color choice, eg.: DB for Dark Bronze PHOTOCONTROL EQUIPMENT PTL-1 Photocontrol - twist-lock cell (120V) PTL-8 Photocontrol - twist-lock cell ( V) PTL-5 Photocontrol - twist-lock cell (480V) PTL-6 Photocontrol - twist-lock cell (347V) PSC Shorting cap - twist-lock CONTROLS SCP and SCPW Start up delay from initial motion detection to fixture illumination is approximately 1-2 seconds SCP - Designed for intermediate coverage area ARM-CL-K-S-XX 60 MAL-KF-X 5.59 FIXTURE CAST ARM SCREW POLE COVER COVER POLE TOP.875 Ø.875 HOLE POLE COVER NUT PLATE SQUARE POLE CAST ADAPTER NUT PLATE ROUND POLE UPSWEPT ARM MOUNT SQUARE & ROUND POLES MAF HORIZONTAL MAST ARM FITTER Ø HOLES #2 DRILL PATTERN FOR POLES Vehicle detection is possible however less reliable than human detection; Vehicle detection is dependent upon the following: rate of speed, mounting height of luminaire and vehicle temperature r =.75 x h d = 1.5 x h Note: Extreme heat or cold temperatures may limit detection. SCPW - Designed for widest coverage area r =.75 x r h =.75 x h d = 1.5 x d h = 1.5 x h Note: Extreme heat or cold temperatures may limit detection SPAULDING LIGHTING, All Rights Reserved For more information visit our website: Printed in USA CL1LED-SPEC 4/15
6 CIMARRON LED Cat.# Job Approvals SPECIFICATIONS Construction: Stylish vertically finned die-cast solid top housing for maximum heat dissipation; Stops collection of unsightly debris from gathering on top of the housing Rugged lower die-cast aluminum heat sink accelerates thermal management and optimizes PCB and optical performance Separate optical and electrical compartment for optimum component operation One piece die cut silicone gasket ensures weather proof seal around each individual LED for IP65 rating Backlight Control (BC) option available for 85% spill light reduction, doesn t change fixture appearance or EPA, recommended for III and IV distributions Stamped bezel provides mechanical compression to seal the optical assembly Complements the Hubbell Southwest series of outdoor fixtures Weight pounds, EPA ft 2 Suitable for applications requiring 3G testing prescribed by ANSI C Optics: Choice of 72 high brightness LED configurations with individual acrylic lenses specially designed for IES II, III, IV and V distributions Auto optics designed for front row 1A and interior rows 2A (see distribution under ordering and page 2) CCT: 00K (80 CRI), 4000K (70 CRI), 5000K (67 CRI), and turtle friendly Amber LED options CRI: 70 Electrical: Universal input voltage VAC, 50/60 Hz Integral step-down transformer for 347V & 480V Ambient operating temperature -40 C to 40 C Automatic thermal self-protection Drivers have greater than 90% power factor and less than 10% THD Optional continuous dimming to 10% or dual circuitry available CERTIFICATIONS/LISTINGS LED Product Partner LED drivers have output power overvoltage, over-current protection and short circuit protection with auto recovery 1050 ma driver available with 90L configuration for increased lumen output LED electrical assembly, including PR devices, consumes no power in the off state Field replaceable surge protection device provides 20KA and 10KV protection meeting ANSI/IEEE C Category C High and Surge Location Category C3. The SPD is designed with a clamping voltage of 1600V at 20KA using industry standard 8/20µs waveform. Controls: Drivers are 0-10V dimming standard. Photocell, occupancy sensor and wireless controls available for complete on/off and dimming control Lumen maintenance: L90 at 60,000 hours (Projected per IESNA TM-21-11) Installation: Two die-cast aluminum arm designs: The decorative arm offers a sleek upswept look while the straight arm follows the housing s contoured lines for continuity of style Fixture ships with arm installed for ease of installation and mounts to #2 drill pattern Wall bracket, mast arm fitter and pole accessories are also available allowing easy mounting for virtually any application Finish: TGIC thermoset polyester powder paint finish applied at nominal 2.5 mil thickness Warranty: Five year limited warranty (for more information visit: resources/warranty/ Listings: Listed to UL1598 and CSA C22.2# for wet locations Models meet DesignLights Consortium (DLC) qualifications, consult DLC website for more details: IDA approved IP65 PRODUCT IMAGE(S) 90 LED 3/4 VIEW LED DIMENSIONS A B C D E F G 6 3/4" 171mm 60 LED 90 LED A A 21 3/4" 552mm Upswept Arm Straight Arm 16" 406mm B B C 6 5/8" 168mm G E 6 5/16" 160mm F D 5 5/8" 143mm 6 1/8" 155mm ORDERING INFORMATION SEE NEXT PAGE 2015 SPAULDING LIGHTING, All Rights Reserved For more information visit our website: Printed in USA CL1LED-SPEC 4/15
7 ORDERING INFORMATION ORDERING EXAMPLE: CL1-A-90LU-5K-3-DB-RPA3 CL1 SERIES NO. OF LEDS CL1 Cimarron LED 90L 90 High brightness LEDs 60L 60 High brightness LEDs L High brightness LEDs MOUNTING A Arm mount construction (6 straight rigid arm included & acceptable for 90 configurations) AD Decorative arm mount const. (6 decorative upswept arm incl. & acceptable for 90 configurations) VOLTAGE U F E4 120V 208V 240V 3K 4K 5K AM7 277V 480V, 60 Hz 00K mA Amber 5000K Amber (590 nm available for Turtle Friendly applications (consult factory) CCT only ma (use with 90L only for higher lumen output) COLOR DB BL WH GR PS RD DISTRIBUTION 2 II 3 III 4 5M 5S 5W 2L Notes: 1- For BL option 90L and 60L; N/A 347V & 480V 2 - BL & CD cannot be combined 3L 3 - Fuse option not available with universal voltage 4 - Select F3 fusing option for 220V 4L 5 - Photocell receptacle not available with BL option 6 - Recommended for III and IV distributions only 2R 7 - Available in 350mA drive current only IV, 5M V fully adjustable dimming with automatic daylight calibration and 3R different time delay settings, must order minimum of one SCP-REMOTE 4R control to program dimming settings (see accessories) 9-120V/277V/347V/480V only 1A 10- Must specify 120V, 208V, 240V or 277V; not available with PR option; consult factory for 347V and 480V application, not available 1AR with BL or CD options. 1AL 2A 2AR 2AL Leave blank for 700mA (standard) 4000K 220V, 50 Hz IV V Medium OPTIONS DRIVE CURRENT 347V, 60 Hz MAF Mast arm fitter for mounting to standard 2 3/8" mast arm bracket, includes 6" straight rigid arm CCT Universal 120V-277V, 50/60 Hz Dark Bronze Black White Gray Platinum Silver Red (premium color) FG Forest Green V Short (premium color) V Wide CC Custom Color II Rotated 90 left BC BL1,2,5 CD2 WB RPA3 RPA4 RPA5 RPA6 F(X)3,4 6 Backlight control Bi-level control Continuous dimming Wall bracket 3 Round pole adapter 4 Round pole adapter 5 Round pole adapter 6 Round pole adapter Fusing (replace X with voltage: 1-120V, 2-208V, 3-240V, 4-277V, 5-480V, 6-347V) SSB Stainless steel LED bezel VG Vandal guard CONTROL OPTIONS WIR WiSCAPE WIRPC WiSCAPE motion control TCM10 For remote wireless control of Child luminaire on the TOTUS network III Rotated 90 left PR(X)5 NEMA Photo cell receptacle IV Rotated 90 left II Rotated 90 right III Rotated 90 right SCP8,9 IV Rotated 90 right Auto Front Row I Controls Guide Auto Front Row I Rotated 90 right SCPW8,9 Auto Front Row I Rotated 90 left Auto Front Row II Auto Front Row II Rotated 90 right Auto Front Row II Rotated 90 left (replace X with voltage: U= , 5=480, 6 =347) Programmable motion control, designed for ' to 40' mounting heights, factory default is 10% light level in unoccupied state (reference coverage area on pg. 3) Programmable motion control, designed for up to 40' mounting heights for widest coverage, factory default is 10% light level in unoccupied state (reference coverage area on page 3) ENERGY SAVING DATA ENERGY DATA Power Factor Total Harmonic Distortion >.9 <10% LIGHT INPUT WATTS ENGINE 120V-277V 347V-480V L-5K L-5K L-5K L-5K L-4K L-4K 90L-4K L-4K L-3K L-3K L-3K L-3K TYPE AUTOMOTIVE DEALERSHIP OPTICS For Automotive Dealership applications Spaulding Lighting has developed two optics designed for enhanced and proper lighting of the auto dealership merchandise and the front row 1A and interior rows 2A (See CL1 distribution information for details) TYPE LUMENS DELIVERED TYPE 4 TYPE 5M TYPE 5S TYPE 5W A - Front Row Auto Optic DRIVERS CURRENT 2@700mA 4@700mA 6@700mA 6@1050mA 2@700mA 4@700mA 6@700mA 6@1050mA 2@700mA 4@700mA 6@700mA 6@1050mA 2A - Drive Lane Auto Optic Optic 1A Maximum illumination on front row display Maximum pole spacing Optic 2A Excellent front row illumination and drive lane Optimal uniformity for drive lane and interior rows ACCESSORIES SEE NEXT PAGE 2015 SPAULDING LIGHTING, All Rights Reserved For more information visit our website: Printed in USA CL1LED-SPEC 4/15
8 ACCESSORIES SCP-REMOTE 9 Remote control for SCP option. Order at least one per project to program and control. CR-RPA3-XX 1 Round pole adapter for straight arm ( ) CR-RPA4-XX 1 Round pole adapter for straight arm ( ) CR-RPA5-XX 1 Round pole adapter for straight arm (5 ) CR-RPA6-XX 1 Round pole adapter for straight arm (6 ) CRD-RPA2-XX 1 Round pole adapter for upswept arm ( ) CRD-RPA3-XX 1 Round pole adapter for upswept arm ( ) CRD-RPA4-XX 1 Round pole adapter for upswept arm ( ) CRD-RPA5-XX 1 Round pole adapter for upswept arm (5 ) CRD-RPA6-XX 1 Round pole adapter for upswept arm (6 ) WB-CR-XX 1 Wall bracket TPLB-XX 1 Twin parallel luminaire bracket MAF-CL-XX 3 Horizontal mast arm fitter for 2 3/8 OD arm. Mounts to standard 6 arm (ordered with fixture) 1 Replace XX with color choice, eg.: DB for Dark Bronze 2 When ordering poles, specify Pole Drill Pattern #2 3 Fixture must include standard 6 arm MOUNTING ACCESSORIES ARM-CL-K-TA-XX 1 ARM-CL-TK-TA-XX 1 ARM-CL-K-S-XX 1 1 Replace XX with color choice, eg.: DB for Dark Bronze 2 Fixture must include standard 6 straight arm Adjustable mounting arm for single fixture (2-3/8 tenon) 5 lbs. 2.3 kgs. Adjustable mounting arm for two fixtures at 180 (2-3/8 tenon) 7 lbs. 3.2 kgs. 10 adjustable arm.5 lbs..05 kgs lbs. 2.6 kgs. ARM-CL-K-TA-XX ARM-CL-TK-TA-XX TENON TOP POLE BRACKET ACCESSORIES MAL-TK-X (2 3/8 OD tenon) (RSS version requires 4 round pole adapter) SETA-XX 1 Square pole tenon adapter (4 at 90 degrees) RETA-XX 1 Round pole tenon adapter (4 at 90 degrees) TETA-XX 1 Hexagonal pole tenon adapter (3 at 120 degrees) 1 Replace XX with color choice, eg.: DB for Dark Bronze PHOTOCONTROL EQUIPMENT PTL-1 Photocontrol - twist-lock cell (120V) PTL-8 Photocontrol - twist-lock cell ( V) PTL-5 Photocontrol - twist-lock cell (480V) PTL-6 Photocontrol - twist-lock cell (347V) PSC Shorting cap - twist-lock CONTROLS SCP and SCPW Start up delay from initial motion detection to fixture illumination is approximately 1-2 seconds SCP - Designed for intermediate coverage area ARM-CL-K-S-XX 60 MAL-KF-X 5.59 FIXTURE CAST ARM SCREW POLE COVER COVER POLE TOP.875 Ø.875 HOLE POLE COVER NUT PLATE SQUARE POLE CAST ADAPTER NUT PLATE ROUND POLE UPSWEPT ARM MOUNT SQUARE & ROUND POLES MAF HORIZONTAL MAST ARM FITTER Ø HOLES #2 DRILL PATTERN FOR POLES Vehicle detection is possible however less reliable than human detection; Vehicle detection is dependent upon the following: rate of speed, mounting height of luminaire and vehicle temperature r =.75 x h d = 1.5 x h Note: Extreme heat or cold temperatures may limit detection. SCPW - Designed for widest coverage area r =.75 x r h =.75 x h d = 1.5 x d h = 1.5 x h Note: Extreme heat or cold temperatures may limit detection SPAULDING LIGHTING, All Rights Reserved For more information visit our website: Printed in USA CL1LED-SPEC 4/15
9 SSS SERIES POLES SQUARE STRAIGHT STEEL Cat.# Job Approvals APPLICATIONS Lighting installations for side and top mounting of luminaires with effective projected area (EPA) not exceeding maximum allowable loading of the specified pole in its installed geographic location. FEATURES SHAFT: One-piece straight steel with square cross section, flat sides and minimum 0.36 radius on all corners. Minimum yield of 46,000 psi (ASTM-A500, Grade B). Longitudinal weld seam to appear flush with shaft side wall. Steel base plate with axial bolt circle slots welded flush to pole shaft having minimum yield of 36,000 psi (ATM-A36). BASE COVER: Two-piece square aluminum base cover included standard. POLE CAP: Pole shaft covered with removable non-metallic cover when applicable. Tenon and post-top configurations also available. HAND HOLE: Rectangular steel-reinforced hand hole (2.5 x 4.5 ). Pole grounding lug located behind gasketed cover. ANCHOR BOLTS: Four galvanized anchor bolts provided per pole with minimum yield of 55,000 psi (modified ASTM-A36). Galvanized hardware with two washers/nuts per bolt for leveling meet or exceed bolt strength. FINISH: Durable Lektrocote TGIC thermoset polyester powder coat paint finish with nominal 3.0 mil thickness. Zinc-rich powder paint prime applied over white metal steel substrate cleaned via mechanical shot blast method. Decorative finish coat available in seven standard colors. Custom colors available. RAL number preferable. Internal protective coating available. Nominal Height Handhole 12" BASE DETAIL Anchor Rod Hex Nut Plain Washer Base Plate Grout Finish Grade Plain Washer Hex Nut Grout after pole is set and plumbed Foundation Level Bolt Projection Engineering of footing by others 20 AMP GFCI RECEPTACLE & COVER COVER GASKET 21 GASKET 1/4 FILLET WELD ALL AROUND. SEE NOTE Q18 OPTION Bolt Square Bolt Circle and Tapered Poles Anchor Bolt Location in Relation to Shaft Rotation Handhole 2015 SPAULDING LIGHTING, All Rights Reserved For more information visit our website: Printed in USA SSSPOLES-SPEC 1/15
10 ORDERING INFORMATION S - S - S TA - DB Cross Section Style Material Nominal Length Nominal Shaft Dia. Shaft Thickness Mounting Finish Pole Ht. Nominal Wind Load Rating 1 Bolt Pole Shaft Wall Circle Bolt Circle Bolt Sq. Base Plate Anchor Bolt Bolt Wt ft m Dim. MPH MPH MPH MPH MPH Thick. (Sug.) (sq.) Size Proj. (lbs) SSS XX-XX " " 11" 8-11" " x 0.75" 3/4 x x 3" 4" 91 SSS XX-XX " " 11" " " 12 x 1" 3/4 x x 3" 4" 106 SSS XX-XX " " 11" 8-11" " x 0.75" 3/4 x x 3" 4" 104 SSS XX-XX " " 11" " " 12 x 1" 3/4 x x 3" 4" 122 SSS XX-XX " " 11" 8-11" " x 0.75" 3/4 x x 3" 4" 116 SSS XX-XX " " 11" 8 1/2-12" 6-8.4" 11 x 1" 3/4 x x 3" 4" 158 SSS XX-XX " " 11" " " 12 x 1" 3/4 x x 3" 4" 138 SSS XX-XX " " 11" 8-11" " x 0.75" 3/4 x x 3" 4" 128 SSS XX-XX " " 11" 8 1/2-12" 6-8.4" 11 x 1" 3/4 x x 3" 4" 176 SSS XX-XX " " 11" " " 12 x 1" 3/4 x x 3" 4" 153 SSS XX-XX " " 11" " " 12 x 1" 3/4 x x 3" 4" 214 SSS XX-XX " " 11" 8 1/ " x 0.75" 3/4 x x 3" 4" 147 SSS XX-XX " " 11" " " 11 x 1" 3/4 x x 3" 4" 201 SSS XX-XX " " 11" " " 12 x 1" 3/4 x x 3" 4" 175 SSS XX-XX " " 11" " 12 x 1" 3/4 x x 3" 4" 243 SSS XX-XX " " 11" 8-11" " x 0.75" 3/4 x x 3" 4" 160 SSS XX-XX " " 11" 8 1/2-12" 6-8.4" 11 x 1" 3/4 x x 3" 4" 225 SSS XX-XX " " 11" " " 12 x 1" 3/4 x x 3" 4" 191 SSS XX-XX " " 11" " " 12 x 1" 3/4 x x 3" 4" 266 SSS XX-XX " " 12" " " 12 x 1" 1 x 36 x 4" 4" 312 SSS XX-XX " NR NR.119" 11" 8-11" " x 0.75" 3/4 x x 3" 4" 190 SSS XX-XX " " 11" " 6-8.4" 11 x 1" 3/4 x x 3" 4" 266 SSS XX-XX " NR.119" 11" " " 12 x 1" 1 x 36 x 4" 4" 231 SSS XX-XX " " 11" " " 12 x 1" 1 x 36 x 4" 4" 324 SSS XX-XX " " 11" " " 12 x 1" 1 x 36 x 4" 4" 437 SSS XX-XX " " 12" " " 12 x 1" 1 x 36 x 4" 4" 404 SSS XX-XX " NR.179" 11" " 6-8.4" 11 x 1" 1 x 36 x 4" 4" 290 SSS XX-XX 9.1 4" NR.179" 11" " 6-8.4" 11 x 1" 1 x 36 x 4" 4" 313 SSS XX-XX 9.1 5" NR.179" 11" " " 12 x 1" 1 x 36 x 4" 4" 398 SSS XX-XX 9.1 5" " 11" " " 12 x 1" 1 x 36 x 4" 4" 537 SSS XX-XX 9.1 6" " 12" " " 12 x 1" 1 x 36 x 4" 4" 467 SSS XX-XX 9.1 6" " 12" " " 12 x 1" 1.25 x 42 x 6" 4" 6 SSS XX-XX " NR.179" 12" " " 12 x 1" 1 x 36 x 4" 4" 538 SSS XX-XX " " 12" " " 12 x 1" 1.25 x 42 x 6" 4" 726 SSS XX-XX " NR NR NR.179" 12" " " 12 x 1" 1 x 36 x 4" 4" 614 SSS XX-XX " NR.250" 12" " " 12 x 1" 1.25 x 42 x 6" 4" Allowable EPA with 1.3 gust factor. To determine max. pole loading weight, multiply allowable EPA by lbs. NOTE Factory supplied template must be used when setting anchor bolts. Hubbell Lighting will deny any claim for incorrect anchorage placement resulting from failure to use factory supplied template and anchor bolts. COMPLETE PART NUMBER REQUIRES SHAFT ABOVE PLUS MOUNTING TYPE, FINISH & APPROPRIATE OPTIONS BELOW MOUNTING TYPE FINISH OPTIONS AX 1 Side - Single DB Dark Bronze Q55 Internal Coating (Hubbell Seal) BX 1 Side - Double at 90 BL Black Q Amp GFCI Receptacle CX 1 Side - Double at 180 WH White and Cover DX 1 Side - Triple at 90 GR Gray Q22 3 Extra Handhole FX 1 Side - Quad at 90 PS Platinum Silver Q Coupling P1 Pad Mount - Spider RD Red (Premium Color) Q Coupling P2 Pad Mount - Yoke FG Forest Green (Premium Color) Q 3 2 Coupling P3 Pad Mount - Yoke CC Custom Color (Consult Factory) Q32 3 Mid-pole Luminaire Bracket (Proformer XL only) PR Primer Only Q41 1st mode vibration damper TA Tenon (2.375 OD) Q42 2nd mode vibration damper TB Tenon (2.875 OD) 1 DRILL PATTERNS: Replace X with LAB Less Anchor Bolts TR 2 1 = Spaulding luminaires with a straight pole (4-bolt), Removable Tenon CSA CSA Certified (consult factory) 2 = Cimarron CR1, MSV and Raven Series luminaires. (2.375 x 4.25) 4 = MSS & DS luminaires, CD Concord Luminaire 5 = Spaulding Detroit III luminaires, 6 = DM luminaires OT No drilling (includes pole cap) 2 Removable tenon used in conjunction with side arm mounting. First specify desired arm configuration followed by the TR notation. Example: SSS C6-TR-DB A B C D E F 3 Specify option location using logic found on cover. Denotes handhole location OPTION ORIENTATION Follow the logic below when ordering location specific options. For each option, include its orientation (in degrees) and its height (in feet). Example: Option Q26 should be ordered as: SSS TA-DB-Q (.5 coupling on the handhole/arm side of pole, 15 feet up from the pole base) 1 spacing required between option. Consult factory for other configurations. Height of option (in feet) SPAULDING LIGHTING, All Rights Reserved For more information visit our website: Printed in USA SSSPOLES-SPEC 1/15 0 Hand hole at 0 orientation
11 LAREDO SERIES LMC - LEDs Cat.# Job Approvals SPECIFICATIONS Intended Use: Full cut-off IDA compliant perimeter or entry lighting for 12-18ft mounting heights that require high light output and maximum energy efficiency. Laredo LMC- LED wallpack provides low installation costs with little or no maintenance and 60%+ energy savings. Ideal for schools, factories, hospitals, warehouses and retail applications. Construction: Decorative die-cast aluminum housing and door. Rugged design protects internal components and provides excellent thermal management for over 70% lumen maintenance at 50,000 hours minimum LED life. Lektrocote series powder paint finishes provide lasting appearance in outdoor environments. Five standard finishes include: Bronze, Black, Gray, White and Platinum. Optics/Electrical LED: High power LEDs delivers up to 6070 lumens at 700mA and up to 3489 lumens at 350mA. Variety of distributions s II, III and IV (Forward throw). High CRI LEDs provide excellent color rendition with up to 100 lumens per watt efficiency. CCT- 5000K/ 67 CRI, 4000K/ 70 CRI, 00K/ 80 CRI Electronic driver 71w system (2 drivers, 2 circuits), 0.4 AMPS max, or 35w (1 driver, 2 circuits), 0.3 amps max, V and 347V and 480V, 50/60Hz 10 KVA surge protector Lenses: Full cut-off distribution - individual acrylic LED optics provide IES II, III and IV distributions. Installation: Quick mount system provides rigid mounting over recessed junction boxes fixture does not require opening for mounting. Foam gasket for sealing to smooth surfaces provided. Superior performance with 5 to 1 spacing to mounting height ratio. Minimum operating temperature is -40 C/ -40 F. Controls: Drivers are 0-10V dimming standard. Photocell and occupancy sensor options available for complete on/off and dimming control. Listings: Listed to UL1598 for wet locations UL certified for thru-wiring. 25 C ambient environments. U.S. Patent No. D563,587 DesignLights Consortium (DLC) qualified, Consult DLC website for more details: LMC-LU Egress Wallpack: Designed to meet strict 1fc minimum requirements. At 12ft mounting height 1fc covers 16x16ft area, well beyond the 10x10ft standard; No uplight, external test button; 120V or 277V only; Rated -20 C to 35 C Warranty: Five year limited warranty (for more information visit: warranty/ PRODUCT IMAGE(S) LMC-LU Motion Sensor DIMENSIONS A LMC-LU LMC-LU BBU B C LED Product Partner A B C (406 mm) (8 mm) (229 mm) ORDERING INFORMATION ORDERING EXAMPLE: LMC-LU-5K-3-1-PC(4) LMC SERIES LMC Laredo Medium Cut-off NUMBER OF LEDS/SOURCE/VOLTAGE LU LEDs, Universal voltage V LF LEDs, 347V L5 LEDs, 480V CCT 3K 00K nominal 4K 4000K nominal 5K 5000K nominal IES DISTRIBUTION 2 II 3 3 III 4 IV (Forward throw) DRIVE CURRENT BLANK STD 700MA MA FINISH 1 Bronze 2 Black 3 Gray 4 White 5 Platinum OPTIONS BBU Integral battery for 120 or 277V rated for -20 C ambient; Available in 350mA (035) drive current only PC(X) 1 Button photocontrol, replace X with voltage, specify 1-120V, 2-208V, 3-240V, 4-277V F(X) 1 Fusing (specify voltage per footnote) SCO 2 Motion sensor On/Off control, No light output when no motion detected SCP 2 Programmable motion control, factory default is 10% light output Controls Guide 1 PC(X) and F Replace X with 1-120V, 2-208V, 3-240V, 4-277V 2 Must order minimum of one SCP-REMOTE to program dimming settings, 0-10V fully adjustable dimming with automatic daylight calibration and different time delay settings, 120V-277V only 3 Egress versions only III 2015 SPAULDING LIGHTING, All Rights Reserved For more information visit our website: Printed in USA LMC-SPEC 4/15
12 ACCESSORIES/REPLACEMENT PARTS - Order Separately LMC-SPC Polycarbonate shield PBT-1 120V button photocontrol PBT /240/277V button photocontrol w, 700mA, V, 0-10V dimming driver KVA surge protector SCP-REMOTE Remote control for SCP option; order at least one per project to program and control PERFORMANCE DATA # OF LEDS 5K (5000K nominal, 67 CRI) 4K (4000K nominal, 70 CRI) 3K (00K nominal, 80 CRI) DRIVE CURRENT SYSTEM WATTS DIST. TYPE LUMENS LPW 1 LUMENS LPW 1 LUMENS LPW 1 BBU mA 35w mA 70w Lumen values are from photometric tests performed in accordance with IESNA LM Data is considered to be representative of the configurations shown. Actual performance may differ as a result of end-user environment and application. Please consult IES files for BUG ratings. ELECTRICAL DATA DRIVE CURRENT # OF LEDS (ma) -035 (350mA) STD. (700mA) INPUT VOLTAGE (V) CURRENT (Amps) SYSTEM POWER (w) PROJECTED LUMEN MAINTENANCE OPERATING HOURS Ambient Temp. 0 25,000 50,000 TM L96 60, ,000 L70 (hours) 25 C / 77 F >539, Projected per IESNA TM * (Nichia 219B, 700mA, 85 C Ts, 10,000hrs) Data references the extrapolated performance projections for the LMC-LU-5K base model in a 40 C ambient, based on 10,000 hours of LED testing per IESNA LM LUMINAIRE AMBIENT TEMPERATURE FACTOR (LATF) AMBIENT TEMPERATURE LUMEN MULTIPLIER 0 C 32 F C 50 F C 68 F C 77 F 1.00 C 86 F C 104 F C 122 F 0.98 Use these factors to determine relative lumen output for average ambient temperatures from 0-40 C ( F) SPAULDING LIGHTING, All Rights Reserved For more information visit our website: Printed in USA LMC-SPEC 4/15
13 LAREDO SERIES LMC - LEDs Cat.# Job Approvals SPECIFICATIONS Intended Use: Full cut-off IDA compliant perimeter or entry lighting for 12-18ft mounting heights that require high light output and maximum energy efficiency. Laredo LMC- LED wallpack provides low installation costs with little or no maintenance and 60%+ energy savings. Ideal for schools, factories, hospitals, warehouses and retail applications. Construction: Decorative die-cast aluminum housing and door. Rugged design protects internal components and provides excellent thermal management for over 70% lumen maintenance at 50,000 hours minimum LED life. Lektrocote series powder paint finishes provide lasting appearance in outdoor environments. Five standard finishes include: Bronze, Black, Gray, White and Platinum. Optics/Electrical LED: High power LEDs delivers up to 6070 lumens at 700mA and up to 3489 lumens at 350mA. Variety of distributions s II, III and IV (Forward throw). High CRI LEDs provide excellent color rendition with up to 100 lumens per watt efficiency. CCT- 5000K/ 67 CRI, 4000K/ 70 CRI, 00K/ 80 CRI Electronic driver 71w system (2 drivers, 2 circuits), 0.4 AMPS max, or 35w (1 driver, 2 circuits), 0.3 amps max, V and 347V and 480V, 50/60Hz 10 KVA surge protector Lenses: Full cut-off distribution - individual acrylic LED optics provide IES II, III and IV distributions. Installation: Quick mount system provides rigid mounting over recessed junction boxes fixture does not require opening for mounting. Foam gasket for sealing to smooth surfaces provided. Superior performance with 5 to 1 spacing to mounting height ratio. Minimum operating temperature is -40 C/ -40 F. Controls: Drivers are 0-10V dimming standard. Photocell and occupancy sensor options available for complete on/off and dimming control. Listings: Listed to UL1598 for wet locations UL certified for thru-wiring. 25 C ambient environments. U.S. Patent No. D563,587 DesignLights Consortium (DLC) qualified, Consult DLC website for more details: LMC-LU Egress Wallpack: Designed to meet strict 1fc minimum requirements. At 12ft mounting height 1fc covers 16x16ft area, well beyond the 10x10ft standard; No uplight, external test button; 120V or 277V only; Rated -20 C to 35 C Warranty: Five year limited warranty (for more information visit: warranty/ PRODUCT IMAGE(S) LMC-LU Motion Sensor DIMENSIONS A LMC-LU LMC-LU BBU B C LED Product Partner A B C (406 mm) (8 mm) (229 mm) ORDERING INFORMATION ORDERING EXAMPLE: LMC-LU-5K-3-1-PC(4) LMC SERIES LMC Laredo Medium Cut-off NUMBER OF LEDS/SOURCE/VOLTAGE LU LEDs, Universal voltage V LF LEDs, 347V L5 LEDs, 480V CCT 3K 00K nominal 4K 4000K nominal 5K 5000K nominal IES DISTRIBUTION 2 II 3 3 III 4 IV (Forward throw) DRIVE CURRENT BLANK STD 700MA MA FINISH 1 Bronze 2 Black 3 Gray 4 White 5 Platinum OPTIONS BBU Integral battery for 120 or 277V rated for -20 C ambient; Available in 350mA (035) drive current only PC(X) 1 Button photocontrol, replace X with voltage, specify 1-120V, 2-208V, 3-240V, 4-277V F(X) 1 Fusing (specify voltage per footnote) SCO 2 Motion sensor On/Off control, No light output when no motion detected SCP 2 Programmable motion control, factory default is 10% light output Controls Guide 1 PC(X) and F Replace X with 1-120V, 2-208V, 3-240V, 4-277V 2 Must order minimum of one SCP-REMOTE to program dimming settings, 0-10V fully adjustable dimming with automatic daylight calibration and different time delay settings, 120V-277V only 3 Egress versions only III 2015 SPAULDING LIGHTING, All Rights Reserved For more information visit our website: Printed in USA LMC-SPEC 4/15
14 ACCESSORIES/REPLACEMENT PARTS - Order Separately LMC-SPC Polycarbonate shield PBT-1 120V button photocontrol PBT /240/277V button photocontrol w, 700mA, V, 0-10V dimming driver KVA surge protector SCP-REMOTE Remote control for SCP option; order at least one per project to program and control PERFORMANCE DATA # OF LEDS 5K (5000K nominal, 67 CRI) 4K (4000K nominal, 70 CRI) 3K (00K nominal, 80 CRI) DRIVE CURRENT SYSTEM WATTS DIST. TYPE LUMENS LPW 1 LUMENS LPW 1 LUMENS LPW 1 BBU mA 35w mA 70w Lumen values are from photometric tests performed in accordance with IESNA LM Data is considered to be representative of the configurations shown. Actual performance may differ as a result of end-user environment and application. Please consult IES files for BUG ratings. ELECTRICAL DATA DRIVE CURRENT # OF LEDS (ma) -035 (350mA) STD. (700mA) INPUT VOLTAGE (V) CURRENT (Amps) SYSTEM POWER (w) PROJECTED LUMEN MAINTENANCE OPERATING HOURS Ambient Temp. 0 25,000 50,000 TM L96 60, ,000 L70 (hours) 25 C / 77 F >539, Projected per IESNA TM * (Nichia 219B, 700mA, 85 C Ts, 10,000hrs) Data references the extrapolated performance projections for the LMC-LU-5K base model in a 40 C ambient, based on 10,000 hours of LED testing per IESNA LM LUMINAIRE AMBIENT TEMPERATURE FACTOR (LATF) AMBIENT TEMPERATURE LUMEN MULTIPLIER 0 C 32 F C 50 F C 68 F C 77 F 1.00 C 86 F C 104 F C 122 F 0.98 Use these factors to determine relative lumen output for average ambient temperatures from 0-40 C ( F) SPAULDING LIGHTING, All Rights Reserved For more information visit our website: Printed in USA LMC-SPEC 4/15
SSS Square Straight Steel
SSS Square Straight Steel Square Straight Steel Shaft One-piece construction Side, Tenon, or Pad mounting available Ground lug standard Galvanized anchor bolts and template included (4-bolt design) Base
More informationLumark PFPRV PREVAIL POLE AND FIXTURE COMBO
DESCRIPTION The Prevail TM LED pole and fixture combination makes selection and installation of poles and fixtures simple. Included is the die-cast Prevail area, site and roadway luminaire with standard
More informationInstallation: Mounting options for horizontal arm, vertical tenon or traditional arm mounting available. Mounting hardware included.
OPTICS Intended Use: The Beacon Viper luminaire is available in two sizes with a wide choice of different LED wattage configurations and optical distributions designed to replace HID lighting up to 000W
More informationLumark PFPRV PREVAIL POLE AND FIXTURE COMBO
DESCRIPTION The Prevail TM LED pole and fixture combination makes selection and installation of poles and fixtures simple. Included is the die-cast Prevail area, site and roadway luminaire with standard
More informationProject: Type: Qty: QH2L. Options QH2L 27 3 /8" 23 3 /16" 3 1 /2" O.D. Pole. Options
Quadro H LED Project: Type: Qty: QHL _ Series Mounting Optics Light Engine CCT Finish Voltage Option _ Pole Series Height Finish Options Series Mounting Optics Light Engine CCT Finish Voltage QHL Quadro
More informationEvolve LED Area Lighting EALS
Evolve LED Area Lighting EALS Product Features The EAL Area Light luminaires are the newest members of the GE Evolve LED Area Light family. They offer a wide range of optical patterns, color temperatures,
More informationBavaria Downs. Chaska, MN. Lighting
Bavaria Downs Chaska, MN Lighting Jason Kinsella City View Electric, Inc. 14309 Lake Drive NE Columbus, MN 55025 Phone 651.659.9496 Fax 651.659.0905 cityviewelectric.com DESCRIPTION Lumark The Prevail
More informationEvolve LED Area Lighting EALP
Evolve LED Area Lighting EALP Product Features The GE Evolve LED Area Light, EALP, is optimized for customers needing an energy saving LED solution while adding flexibility, style and scalability at at
More informationARIETA 13 Architectural LED Area Luminaire AR13 M2 Series Specification Data Sheet
Luminaire Data Weight 15.4 lbs [7 kg] EPA 0.47 ft 2 Project Type Catalog No. 8.0 in [203 mm] 8.7 in [220 mm] 8.0 in [203 mm] 8.7 in [220 mm] Ordering Information Sample Catalog No. AR13 MV NW 5 BK 700
More informationARIETA 18 Architectural LED Area Luminaire AR18 M2 Series Specification Data Sheet
Project Type Catalog No. Luminaire Data Weight 24 lbs [10.9 kg] EPA 0.55 ft 2 Ordering Information Sample Catalog No. AR18 MV NW 3 DB 700 HSS Product LED Code Voltage Nominal Color Temperature Distribution
More informationOSQ Series OSQ LED Area/Flood Luminaire Large
OSQ Series OSQ LED Area/Flood Luminaire Large Product Description DA Mount The OSQ Area/Flood luminaire blends extreme optical control, advanced thermal management and modern, clean aesthetics. Built to
More informationGE Evolve LED Area Lighting Scalable EASC High Lumen
GE Evolve LED Area Lighting Scalable EASC High Lumen Product Features The next evolution of the GE Evolve EASC LED Area Light continues to deliver outstanding features, while adding greater lumen output,
More informationPerimaliter Wallpacks
Perimaliter Wallpacks Perimaliter III PVL3 / PGM3 Perimaliter II PGL Solutions for Perimeter/Area Lighting Perimaliter Wallpacks The Perimaliter wallpack has been the design leader in refractor wallpacks
More informationARIETA 13 Architectural LED Area Luminaire AR13 N-Series Specification Data Sheet
Luminaire Data Weight 15.4 lbs [7 kg] EPA 0.47 ft 2 Project Type Catalog No. 25.6 in [650 mm] 8.0 in [203 mm] 13.5 in [343 mm] 3.78 in [96 mm] Ordering Information Sample Catalog No. AR13 48N MV NW 5 BK
More informationProject: Type: Qty: SA1L. Optics Mounting Light Engine CCT Finish Voltage Options. Series SA1L-XX-1-NH SA1L-XX /2" O.D.
Saturn LED Project: Type: Qty: SAL Series Optics Mounting Light Engine CCT Finish Voltage Pole Series Height Finish Pole Options Option Series SAL Saturn LED Optics Mounting Light Engine CCT Finish Voltage
More informationAutobahn Series ATB0 Roadway Lighting
Autobahn Series ATB0 Roadway Lighting PRODUCT OVERVIEW Features: OPTICAL Same Light: Performance is comparable to 70-250W HPS roadway luminaires. White Light: Correlated color temperature - 4000K, 70 CRI
More informationGLEON GALLEON LED Light Squares
DESCRIPTION The Galleon LED luminaire delivers exceptional performance in a highly scalable, low-profile design. Patented, high-efficiency AccuLED system provides uniform and energy conscious illumination
More informationTYPE APPROVALS. Diffusion lens for low glare comfort NX wireless control options mm mm. EPA Side View mm. 23.
JOB TYPE NOTES FEATURES Elegant form factor High performance optics up to 35,000 delivered lumens APPROVALS Diffusion lens for low glare comfort NX wireless control options CERTIFICATIONS SPECIFICATIONS
More information1SA / ALT3P35/ 120L5K277/ WH/ A26
Date: Jun 20, 2013 1SA/ALT3P70/120L3K240/DB/A-33 BB-SGL-ALT Catalog number: Approvals: Mtg. Fixture Electrical Module Finish Options See page 2 See pages 3-4 Ordering Example: 1SA / ALT3P35/ 120L5K277/
More information304 Series LED Recessed Canopy Luminaires
CAN-304-PS-RS " 6.6" [ 155mm ] [ 169mm ] Notes: 14.0" SQ [ 356mm ] Cut Out Luminaire Clearance Product Family Optic Mounting # of LEDs LED Voltage Color Drive Factory-Installed Options ( x 10 ) Series
More informationARIETA 13 Architectural LED Area Luminaire AR13 N-Series Specification Data Sheet
Luminaire Data Weight 15.4 lbs [7 kg] EPA 0.47 ft 2 Project Type Catalog No. 25.6 in [650 mm] 8.0 in [203 mm] 13.5 in [343 mm] 3.78 in [96 mm] Ordering Information Sample Catalog No. AR13 48N MV NW 5 BK
More informationQty: Pole Order Code: Series Height Finish Options. R4 Type IV. R5R Type V Round. Distribution. Distribution. 4C Quadruple Cluster.
Date: Customer: Project: Type: Qty: Beta Pendant LED Order Code: BPL BPL Series - - - - - - - - BPL Beta Pendant LED Pole Order Code: - - - Series Height Finish Options Optics R Type I Distribution R Type
More informationVisor Compact Architectural LED Wallpack. Technical Specifications VISOR TM. Visor Configuration Information. Project Catalog Number Type Date
VISOR TM led wallpack Visor compact architectural LED wallpacks replace up to 250W pulse start metal halide wall-mounted fixtures in perimeter, security, and entrance way applications while consuming up
More informationGreenCobra LED Street Light GCL G-Series Specification Data Sheet
GreenCobra Street Light Project Type Catalog No. Luminaire Data Weight 18 lbs [8.17 kg] EPA 0.8 ft. 2 5.7 in [145 mm] 5 in [127 mm] 5.7 in [145 mm] 15.2 in [386 mm] 15.2 in [386 mm] Ordering Information
More informationLaredo Decorative Wallpack Family
Outdoor Lighting Laredo Decorative Wallpack Family NEW Selections Full Cutoff IDA Compliant Laredo Application Guide Compact LCC 6-1ft mounting height The Laredo Family meets the Strictest Lighting Codes
More informationEvolve LED Area Lighting
GE Lighting Evolve LED Area Lighting EALS imagination at work Product Features The GE Evolve LED Area Light, EALS, is optimized for customers requesting an energy saving LED solution while adding greater
More informationQty: R4 Type IV Distribution. B4 Two 12V 146 Ah. B5 One 12V 176 Ah. P4 150W Double. 4 XXX 4 hours PM 0 hours AM. 5 XXX 6 hours PM 0 hours AM PM4 45
Date: Customer: Project: Type: Qty: SonneLITER LED Solar Order Code: SDSLS SDSLS Series - - - - - - - - - - SDSLS SonneLITER LED Solar Optics R Type I Distribution R Type II Distribution R Type III Distribution
More information19.0" (482mm) Performance Summary 3.1" (79mm) NanoOptic Precision Delivery Grid optic Receptacle location (ordered as an option)
(69mm) 19.0" (48mm) OSQ Series 3" (79mm) OSQ LED Area/Flood Luminaire Medium Product Description NEMA Photocell Receptacle location (ordered as an option) DA Mount The OSQ Area/Flood luminaire blends extreme
More informationTYPE APPROVALS. Diffusion lens for low glare comfort NX wireless control options mm. EPA Side View mm mm. 27.
JOB TYPE NOTES FEATURES Elegant form factor High performance optics up to 50,000 delivered lumens APPROVALS Diffusion lens for low glare comfort NX wireless control options CERTIFICATIONS SPECIFICATIONS
More information1 With internal stepdown transformer 26 7 /8" (683mm)
Project: Type: _ RRSL L55 Series Mounting Height Light CCT Finish Voltage Engine Options Qty: Series RRSL Ritorno Round Symmetrical LED Mounting Height Light Engine CCT Finish Voltage Options 1 Single
More informationXSP High Output Series XSP2 High Output LED Street/Area Luminaire Double Module
XSP High Output Series XSP High Output LED Street/Area Luminaire Double Module Product Description Designed from the ground up as a totally optimized LED street and area lighting system, the XSP High Output
More informationMVOLT
High Lumen LED Flood Luminaire Notes Type Hit the Tab key or mouse over the page to see all interactive elements. Introduction Specifications EPA: 5.4 ft 2 (0.50 m 2 ) Depth: 10 (25.4 cm) Width: 25 (62.5
More informationQty: L50 50W. B4 Two 12V 146 Ah. B5 One 12V 176 Ah. P4 150W Double. 4 XXX 4 hours PM 0 hours AM. 5 XXX 6 hours PM 0 hours AM PM4 45 PM6 60.
Date: Customer: Project: Type: Qty: Avanza 450 LED Solar Order Code: AV4LS - - - - - - - - - - AV4LS Series AV4LS Avanza 450 LED Solar Optics RW Type III Distribution (Wide) RN Type III Distribution (Narrow)
More informationCree Edge Series LED Area Luminaire Round
Cree Edge Series LED Area Luminaire Round Product Description The Cree Edge Series has a slim, low profile design. Its rugged cast aluminum housing minimizes wind load requirements and features an integral,
More informationCC/CCS21 21" Post Top Mounted, Curvilinear, LED revision 5/9/11 kim_cc21pled_spec.pdf
Catalog number: Approvals: / / / / Mtg. Fixture Electrical Module Finish Options See page 4 See page 2 See page 3 Select pole from Kim Arms and Poles Selection Guide. If pole is provided by others indicate
More informationCree Edge Series LED Area/Flood Luminaire
Cree Edge Series LED Area/Flood Luminaire Product Description The Cree Edge Series has a slim, low profile design. Its rugged cast aluminum housing minimizes wind load requirements and features an integral,
More informationOSQ LED Area/Flood Luminaire Medium
OSQ Series OSQ LED Area/Flood Luminaire Medium Product Description The OSQ Area/Flood luminaire blends extreme optical control, advanced thermal management and modern, clean aesthetics. Built to last,
More informationE-Cobra LED Street and Area Light EC M2 Series Specification Data Sheet
Project Type Catalog No. Luminaire Data L Weight EPA EC1 16.1 in [409 mm] 10.8 lb [4.9 kg] 0.40 ft 2 EC3 20.8 in [528 mm] 12.7 lb [5.8 kg] 0.45 ft 2 EC4 23.5 in [597 mm] 14.0 lb [6.3kg] 0.48 ft 2 30.6
More informationBetaLED Recessed Canopy Luminaires
CAN-227-5M-RM "A" 8.8in [225mm] Driver Housing 350 ma HL option, 525mA, 700mA DIM A 12.8" [325mm] 23.8" [605mm] Fixture DIM B DIM C 90 LED 21.6" [549mm] 20.6" [523mm] 120 LED 26.2" [665mm] 25.125" [638mm]
More informationSaturn Cutoff. Order Code: Pole Order Code: Series Height Finish Options. Customer: Date: Project: Qty: Type: SAC Saturn Cutoff SAC
Date: Customer: Project: Type: Qty: Saturn Cutoff Order Code: SAC - - - - - - - - SAC Series SAC Saturn Cutoff Pole Order Code: - - - Series Height Finish Options Optics R Type II Distribution R Type V
More informationOSQ High Output LED Area/Flood Luminaire featuring Cree TrueWhite Technology. Product Specifications. Electrical Data*
OSQ Series Product Description DA Mount The OSQ High Output Area/Flood luminaire blends extreme optical control, advanced thermal management and modern, clean aesthetics. Built to last, the housing is
More informationThe PREMIER TM. II Series
The PREMIER TM II Series Contemporary architectural design meets the new generation of LED technology in the new Premier II Series by Visionaire Lighting. It is the perfect complement to any university
More informationPromenade TM Series LED PRMD
FEATURES Reliable, uniform, glare free illumination Types II, III, IV, V and custom distributions 1 3000K, 4000K, 5000K CCT 0-10V dimming ready Integral surge suppression Life thermal protection 13 standard
More informationPaseo. Luminaire CE21T4UF Pole PA40 base cover BD11
Paseo Luminaire CE21T4UF Pole PA40 base cover BD11 CE21T4B Paseo DETAILS With a flat lens design, the PASEO is ideal for modern design applications with light control in mind. The optional Utility Fitter
More informationLEDMPAL15 15 Watt Multi-Purpose LED Area Light
LEDMPAL15 15 Watt Multi-Purpose LED Area Light Project: Type: Catalog #: STANDARD FEATURES WET 1kV Surge Protection Available in 3000k (warm white), 4000K (neutral white) and 5000K (cool white). * Long-life
More informationXSP Series XSPR LED Street/Area Luminaire Version A
XSP Series Product Description In addition to a low initial cost, the XSPR LED Street luminaire maintains the familiar look of the traditional cobrahead design and delivers substantial energy savings while
More informationAutobahn Series ATB2 Roadway Lighting
P R O D U C T O V E R V I E W Applications: Roadways Off ramps Residential streets Parking lots 355.6 mm (14 ) DIMENSIONS 101.6 mm (4 ) 787.4 mm (31 ) Effective Projected Area (EPA) The EPA for the ATB2
More informationRSW Series RSW LED Street Luminaire Small
RSW Series RSW LED Street Luminaire Small Product Description The Cree RSW Series, utilizing WaveMax Technology, will transform the way utilities and municipalities light their residential streets. With
More informationTYPE APPROVALS. Diffused lens option Programmable occupancy sensor (dimming) SiteSync wireless controls 130+ lumens per watt
JOB TYPE NOTES APPROVALS FEATURES -5 to +10 tilt adjustment High performance optics deliver up to 15,000 lumens up or down mountable without modification d lens option Programmable occupancy sensor (dimming)
More informationQty: ELDC ELO Domed Top Column ft ft. 1G4 Quadruple Stack. SV Silver. BL Semi-Matte Black 347 1, ,6 347V 480V
Date: Customer: Project: Type: Qty: Order Code: - - - - - - - Series ELFC ELO Flat Top Column ELDC ELO Domed Top Column Height 8 8 ft 9 9 ft 0 0 ft ft ft ft 4 4 ft 5 5 ft 6 6 ft 7 7 ft 8 8 ft Optic T Forward
More informationRitorno Square Asymmetrical LED
Date: Customer: Project: Type: Qty: Ritorno Square Asymmetrical LED Order Code: RSAL RSAL Series - - - - - - - Pole Order Code: - - - Series Height Finish Options RSAL Ritorno Square Asymmetrical LED Mounting
More informationSaturn 2 LED 5YEAR LED WARRANTY. Order Code: Pole Order Code: Series Height Finish Options. Customer: Date: Project: Qty: Type: SA2L SA2L SA2L
Date: Customer: Project: Type: Qty: Saturn LED Order Code: SAL - - - - - - - - SAL Series SAL Saturn LED Pole Order Code: - - - Series Height Finish Options Optics TS Tritec Symmetric TA Tritec Asymmetric
More informationQty: R5 Type V Distribution. W Wall Mount. LG ma/101w K. SP Specify Premium Color. SV Silver. * Equipped with step-down transformer
Date: Customer: Project: Type: Qty: Saturn Cutoff LED Order Code: SACL Series - - - - - - - - SACL Saturn Cutoff LED Pole Order Code: - - - Series Height Finish Options Optics R Type I Distribution R Type
More informationVINCI-LED Wall/Area/Flood Lighting
Job Information Type: VINCI-LED Catalog #: Project: Comments: Prepared by: YEAR WARRANTY WARRANTY TEN INCLUDES LABOR ALLOWANCE Vinci Vinci Large 7⅞ ¼ ⅝ 9¾ ½ ⅛ Applications Wall/Surface Post/Bollard Low
More informationAutobahn Series ATBO Roadway Lighting
Autobahn Series ATBO Roadway Lighting P R O D U C T O V E R V I E W Applications: Roadways Off ramps Residential streets Parking lots DIMENSIONS Effective Projected Area (EPA): The EPA for the ATB0 is
More informationDriver Info. Construction Thermal Management: Superior thermal management with die-cast aluminum heatsink. Ambient Temperature:
WP3LED55 Project: Type: Prepared By: Date: 82W, 65W and 55W LED wallpacks. Available with up to 9,000 lumens and 121 LPW. Up to 100,000 hour L70 lifespan. 5-Year Warranty. Color: Bronze Weight: 16.8 lbs
More informationLumark NAV NAVION. 1-6 Light Squares
DESCRIPTION The Navion area, site and roadway LED luminaire combines world class optical performance, energy efficiency, and outstanding versatility to meet the requirements of any area, site or roadway
More information80 Watt Multi-Purpose LED Area Light
JGMPAL Watt Multi-Purpose LED Area Light STANDARD Project: Type: Catalog #: WET kv Surge Protection IP65 The JGMPAL series is a group of architectural LED area luminaires designed to illuminate parking
More informationDomia DETAILS CY55P1A CY55T4 IP67
Domia Domia DETAILS The Domia offers smooth curves and a timeless shape blends easily into any environment. With a flat lens design, the DOMIA family enhances any project while offering high performance
More informationXSP Series XSP2 LED Street/Area Luminaire Double Module Version C
XSP Series XSP LED Street/Area Luminaire Double Module Version C Product Description Designed from the ground up as a totally optimized LED street and area lighting system, the XSP Series delivers incredible
More informationBOW SX - LED Luminaire
BOW SX - LED Luminaire The new BOW SX LED Series offers clean, functional styling that is defined by its sleek low profile design and rugged construction. It combines the latest LED performance and advanced
More informationLevanto DETAILS. IP67 EPA: 0.96 FT 2 Weight: 35 lbs - 16 kg
Levanto CLE17T4A Levanto DETAILS LEVANTO s sleek arms and slim heat sink highlights its contemporary style. The Utility Fitter and superior thermal management achieves remarkable efficacy. Its refined
More information. 100G. USSL series, MADE IN THE USA Solar street lights
USSL series, MADE IN THE USA Solar street lights. 100G General Specifications Light Fixture (Beta-LED CREE LED Fixture) Power consumption Lumen Color temperature IES lighting type Material 70 W 5180 lumens
More informationGE Evolve LED Area Lighting Scalable EASC
GE Evolve LED Area Lighting Scalable EASC Product Features The next evolution of the GE Evolve LED Area Light continues to deliver outstanding features, while adding greater flexibility, style and scalability.
More informationCatalog # Project. Comments. Prepared by. 11" [279mm] 8-3/4" [222mm] ESCUTCHEON PLATES. 2-5/8" [67mm] 3/4" [19mm] Dia. Hole. 3" [77mm] 1-1/2" [39mm]
DESPTION SPECIFICATION FEATURES at The patented Lumark Crosstour MAXX LED Wall Pack Series of luminaries provides low-profile architectural style with super bright, energy-efficient LEDs. The rugged die-cast
More informationTaxonomies, Classifications, and Categories LED FLOODLIGHTS, WALLPACKS, BOLLARDS & LANDSCAPE LIGHTING
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 XT0R5A 50W Led Wallpack Catalog Number Manufacturer Description Weight per unit Product Category Features amperage rating
More informationEvolve LED Roadway Lighting
GE Lighting Evolve LED Roadway Lighting Scalable Specification Grade Cobrahead (ERS, ERS, ERS3 & ERS4) imagination at work Product Features From local to major roadways, the GE Evolve LED Roadway Scalable
More informationInvue MSA MESA LED. 1-6 LightBARs
DESCRIPTION The geometric form of MESA LED luminaire allows it to adapt to either contemporary or traditional architectural settings. Available in single or twin pole mount configurations with optional
More informationBDT Product Sales & Support (951) (800)
BDT Product Sales & Support (951)530-3360 (800)325-0380 support@bdtenergygroup.com BDT Product Sales & Support (951)530-3360 BOW LX LED Dimensional Drawings A C B The new BOW LX LED Series continues the
More informationMeridian DETAILS CA10T4A CA10T4D CA13T4A. IP66 EPA: 2.2 FT 2 Weight: 27 lbs - 12 kg
Meridian Meridian DETAILS The elegant modular design of the MERIDIAN series allows adaptability to all surroundings and perfect integration with many different environments. Composed of cast and extruded
More informationMA20/MA21 SERIES MAYA - LED Post Top
TYPE: QUANTITY: PROJECT: / SERIES Post Top CATALOG NUMBER: FIXTURE WATTAGE VOLTAGE FINISH OPTION OPTION OPTION OPTION 7 1 2 3 4 1- Cast aluminum LED heat sink. 2- Optical system assembly. 3- Set of two
More informationLSA TM series. BBE LED Roadway, Area & Parking Lighting Luminaire V9: LSA-04/06/16. Performance Data:
V9: LSA-04/06/16 BBE LED Roadway, Area & Parking Lighting Luminaire LSA TM series Performance Data: Input Voltage: 120-277Vac / 347-480Vac 50/60Hz Power: 30-250W Luminous flux: 3400-25500lm Up to 118LPW@700mA
More informationHAZARDOUS LOCATION CLASSIFIED AREAS LW1 AND LW2 SERIES DOWN OR UP OPTICS
H6..H Project: Fixture Type: Location: Contact/Phone: FINIA LED WALL MOUNTED HAZARDOUS LOCATION CLASSIFIED AREAS LW AND LW SERIES DOWN OR UP OPTICS LED W, W, AND 8W PRODUCT DESCRIPTION The Finia LED LW
More informationK601D COACH LANTERN - LED PRODUCT SPECIFICATIONS
The K601D is a cost effective coach lantern with a historical appearance that offers high performance Advanced LED Technology with our signature P4 optical system. It has excellent spacing and low glare
More informationMorino DETAILS IP67. Contact factory for WIRELESS CONTROLS and further details REV. 5: 06/18. EPA: 1.8 FT 2 Weight: 35 lbs - 16 kg
Morino Morino DETAILS The updated Victorian style Morino, designed with decorative arms that lend itself perfectly to any post classic settings. Conceived with a high efficiency heat sink, integrated Utility
More informationOSQ Series LED Area/Flood Luminaire Medium
10.6" (69mm) 19.0" (48mm) OSQ Series LED rea/flood Luminaire Medium Product Description 3" (79mm) NEM Photocell (R Option Only) D Mount The OSQ rea/flood luminaire blends extreme optical control, advanced
More informationSymphony DETAILS. IP66 EPA: 1.8 FT 2 Weight: 52 lbs - 24 kg
DETAILS The SYMPHONY is a new take on the traditional acorn design and it performs with our Galaxy engine and offers higher wattages and optical performance for the utility market. Available with and without
More information304 Series LED Recessed Canopy Luminaire
304 Series LED Recessed Canopy Luminaire Product Description Luminaire housing is constructed from rugged die cast aluminum components (RS Mount) or die cast and extruded aluminum components (RD Mount).
More informationuse pulldowns to assign fixture # to arm locations: K K K 14W LED 27W LED 1 Full-Cutoff optics
Lines 2, 3 and 4 and line quantities applicable to SSx mounting only Project: Type: Qty: FIT # qty SERIES - OPTICS - MOUNTING - LIGHT ENGINE - CCT - FINISH - VOLTAGE - ACCESS.1 - ACCESS.2 1 OLML- - - -
More informationLEDway Series LEDway High Output Street Light Single Module
LEDway Series LEDway High Output Street Light Single Module Product Description LEDway High Output Streetlight series for roadway lighting expands the application range replacing from 70W to 400W HPS.
More informationLimited Warranty : 10 years on luminaire / 10 years on Colorfast DeltaGuard finish 6.1" (155mm) Color Options. Drive Current
CAN-304-PS-RD 304 Series Canopy Luminaire Petroleum Symmetric Recessed Mount for Double Skin Canopies Product Description Slim, low profile design. Luminaire is constructed from rugged die-cast and extruded
More informationEvolve LED Wall Pack. N Series (EWNB)
Evolve LED Wall Pack N Series (EWNB) Product Features The next generation of the GE Evolve LED Wall Pack is designed to efficiently illuminate walkways, area, and general lighting applications. The EWNB
More informationPole Series. Series Reflector Lens Mounting Lamping Finish Voltage. S w S w S w S w
Type: Qty: QHO Series Reflector Lens Mounting Lamping Finish Voltage QHO Quadro HO R Type II Aluminum reflector R5 Type V Aluminum reflector L S Project: Flat Glass Sagged Glass Series Reflector Lens Mounting
More informationLUM SERIES-PLED w/ POLE RATED FOR 100MPH SHAFT
EXPEDITED AVAILABILITY LUM SERIES-PLED w/ POLE RATED FOR 100MPH SHAFT PROJECT NAME: FIXTURE TYPE: FIXTURE HOUSING Heavy cast low copper aluminum assembly (A360 alloy,
More informationGE Evolve LED Post Top Contemporary Twin Support Post Top (EPTC)
GE Evolve LED Post Top Contemporary Twin Support Post Top (EPTC) GE Evolve LED Post Top Lighting Contemporary Twin Support Post Top (EPTC) The GE Evolve LED Contemporary Twin Support Post Top (EPTC) offers
More informationCapella 3. Project Name. Construction. Optical System. Product Applications
Product # Type Date Project Name Project Location Capella 3 Construction Housing and lens frame are constructed from heavy-duty low copper die-cast aluminum. Material is structurally rigid and uniformly
More informationLevanto. details CLE17T4A
Augusta Levanto Levanto details 2 LEVANTO s sleek arm design and slim heat sink highlights its contemporary style. The Utility Fitter and superior thermal management achieves remarkable efficacy. Its refined
More informationCampana DETAILS CN55P1A. IP67 EPA: 1.8 FT 2 Weight: 52 lbs - 24 kg CN55P1B
Campana Campana DETAILS Luminaires in the CAMPANA series coexist perfectly with environments such as parks, pedestrian areas, waterfront projects, shopping centres, streets or avenues. This series of luminaires
More informationLEDMPALPRO LED Area Luminaire
CATALOG NUMBER: NOTES: FIXTURE TYPE: PROJECT: FEATURES DIMENSIONS 2 ¾ 12 ⅝ 1 ⅝ Weight: 8.2 lbs. (8W), 1.8 lbs. (1W) & 11 lbs. (14W) PRODUCT DESCRIPTION The LEDMPALPRO series is a group of premium architectural
More informationQuadroMAX LED FIXTURE QM SERIES
PROJECT NAME: CATALOG NUMBER: NOTES: FIXTURE SCHEDULE: Page: 1 of 8 QuadroMAX LED FIXTURE Mounting Options Slipfitter Fixed Slipfitter Knuckle Pole Mount Fixed Surface Mount Knuckle Surface Mount Trunnion
More informationCN12P1A GCPO REV. 1: 12/16
Marina CN12P1A GCPO Marina PENDANT The MARINA pendant is a mid-century modern classic design that compliment many urban environments. The latest version offers a unique look by retaining the iconic cage
More informationPG Series. Our PG Series has now been expanded to complete your entire site needs. With added housing shapes of round and square we offer
PG Series At Visionaire Lighting we are always looking to advance and engineer the latest in LED technology and lighting. In our efforts of advancement, we have taken our highly rated PGA LED Luminaire
More informationStreetworks NVN NAVION. 1-6 Light Squares
DESCRIPTION The Navion roadway LED luminaire combines world class optical performance, energy efficiency, and outstanding versatility to meet the requirements of any roadway application. Patented AccuLED
More informationCatalog # Project. Comments. Prepared by. 21-3/4" [553mm] "B" Weight with Arm (lbs.) EPA with Arm 2 TYPE "N" (Sq. Ft.) 33 (15.0 kgs.) 0.
DESCRIPTION The Galleon LED luminaire delivers exceptional performance in a highly scalable, low-profile design. Patented, high-efficiency AccuLED system provides uniform and energy conscious illumination
More informationAugusta POST-TOP. IP66 EPA: 2.2 FT 2 Weight: 48 lbs - 22 kg
Augusta Augusta POST-TOP The AUGUSTA Series, with its traditional styling, is the perfect companion for open areas such as park pathways or streets. Its elegant design provides all the charm needed to
More informationWPP25 250W MP Wal-Pak Borosilicate Glass Hinged/Removabl
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 WPP25 250W MP Wal-Pak Borosilicate Glass Hinged/Removabl Catalog Number Manufacturer Description Weight per unit Product
More informationLaredo - Decorative Wallpack Family
Outdoor Lighting Laredo - Decorative Wallpack Family Full Cutoff New Laredo Application Guide Compact LCC 6-1ft mounting height The Laredo Family meets the strictest lighting codes Full Cutoff Star View
More informationPhuzion LED High Bay Wet location listed
Catalog Number Notes Type Phuzion Wet location listed DesignLights Consortium (DLC) qualified product. Not all versions of this product may be DLC qualified. Please check the DLC Qualified Products List
More informationAugusta POST-TOP. IP66 EPA: 2.2 FT 2 Weight: 48 lbs - 22 kg
Augusta Augusta POST-TOP The AUGUSTA Series, with its traditional styling, is the perfect companion for open areas such as park pathways or streets. Its elegant design provides all the charm needed to
More informationTYPE APPROVALS. Fixture Finish. LG Light Gray BL Black DB Dark Bronze GT Graphite PS Platinum Silver TT Titanium WH White CC Custom Color 2.
JOB NOTES TYPE APPROVALS FEATURES Independently aimed LEAR modules 355 rotation and 70 tilt module adjustment and -5 to +30 housing adjustment Wide range of drive currents available Design software interface
More information