Original Parts & Accessories Installation Instructions

Transcription

1 Original Parts & Accessories Installation Instructions BMW R1100S Sport Rear Stand Part Number: Sport Rear Stand Overview: The Sport Rear Stand is designed to lift and support the R 1100 S with the rear wheel off the ground; allowing removal, and easing cleaning and maintenance chores of the rear wheel and suspension. It holds the motorcycle by engaging receivers (spools) attached to the motorcycle at existing centerstand mounting holes in the frame rails. - The spools can be installed, and the stand configured, in different ways to accommodate motorcycles with, or without, engine spoilers (lower bodywork) installed. - The stand is height adjustable. The lower position raises the rear of the motorcycle just enough to allow the rear wheel to be removed. The higher position allows wheel removal even when a front stand is in use, tilting the motorcycle back. These instructions must be read carefully and thoroughly before installation or use. - BMW of North America, LLC and BMW Motorrad USA accept no liability for damage caused by failure to observe the installation/use instructions. - BMW Motorrad USA recommends that an authorized BMW Motorcycle Retailer install this accessory. Before installation, one should carefully consider whether one is in possession of the necessary technical skills and workshop tools to complete the installation properly. If not, any BMW Motorcycle Retailer will gladly install this accessory. Special Tools needed for installation: 6mm allen (internal hex) wrench Electric drill 5/16 (or 8mm) drill bit Blue Thread-lock compound The following symbols are used in these instructions for safety notes: Warning Warning indicates a potentially hazardous situation, which if not avoided, could result in death or injury. Caution Caution indicates a potentially hazardous situation or unsafe practice that may cause property damage or may invalidate your vehicle warranty. Note Tips for facilitation of operation, control and adjustment, as well as maintenance work. Installation Overview: The Sport Rear Stand is designed to lift and support the R 1100 S with the rear wheel off the ground. The stand can be configured to accept motorcycles: 1. Without any lower spoiler installed (Diagram A, below). 2. With Factory CF Lower Spoiler Kit (PN ) installed (Diagram A, below). 3. With Factory CF Belly Pan as per BMW R1100S Replika installed (Diagram B, below). The kit includes all of the necessary hardware for these two configurations. See diagrams that follow for details BMW of North America, LLC All rights reserved. BMW logo and trademarks are registered. Not to be reproduced without written permission of BMW of North America, LLC. Printed in USA Page 1 of 5

2 The Sport Rear Stand is for supporting the motorcycle without the rider. The Stand must be used only on smooth, dry and level surfaces, with the motorcycle in gear. If using a front stand together with the rear stand, THE REAR STAND MUST BE PUT IN PLACE FIRST AND REMOVED LAST. Never allow the motorcycle to be supported by a front stand alone. When installing or operating the Sport Rear Stand, always have someone nearby assist with the process. Caution: The stand must be installed on the motorcycle as per the appropriate diagram. DO NOT ATTEMPT TO MODIFY THE INSTALLATION. The Sport Rear Stand has been designed and tested for use on the R1100S only. The Stand is intended for closed-course/off-road use only. If the motorcycle is equipped with a factory installed center stand, both it, and the pressed-in frame bushing must be removed to allow installation and operation of the Sport Rear stand. In this situation, BMW Motorrad USA recommends contacting your authorized BMW Motorcycle Retailer for assistance. Page 2 of 5

3 Installation Procedure: R 1100 S models without spoiler R 1100 S models with Factory CF Spoiler (PN ) installed. DIAGRAM A NOTE: <LIFT PLATES MOUNTED ON INSIDE OF TUBES> VIEW FROM BACK, LOOKING TOWARD FRONT OF BIKE 1. Park the motorcycle on a smooth, dry and level surface using the standard side stand. Ensure that the ignition and steering lock are OFF and the motorcycle is in gear. 2. Locate the Center Stand mounting holes in the frame on either side of the bike. 3. Position the special backing nuts in the back of the center stand mounting holes and draw them completely into the hole utilizing the short 8mm screw and short spacer provided (image a, b, c) 4. With the backing nuts installed, continue installing the remainder of the hardware referring to DIAGRAM A (above). Once the stand spool receivers are installed, re-install the Sport Spoiler, if utilized. a. b. c. Secure spool attachment bolts with thread-locking compound, e.g. Loctite Blue, not supplied. Page 3 of 5

4 Installation Procedure: R 1100 S models with Replika CF Bellypan Installed. DIAGRAM B Replika Bellypan VIEW FROM BACK, LOOKING TOWARD FRONT OF BIKE 1. Park the motorcycle on a smooth, dry and level surface using the standard side stand. Ensure that the ignition and steering lock are OFF and the motorcycle is in gear. 2. Carefully remove the bellypan. Place aside on a protected surface to avoid possible damage to the bellypan. 3. Remove rear rubber bellypan support plugs from both sides of frame. Store parts for future use. 4. Position the special backing nuts in the back of the center stand mounting holes and draw them completely into the hole utilizing the short 8mm screw and short spacer provided (image d, e). 5. Before re-installing the bellypan, both existing mounting holes, one in each side, must be enlarged carefully using a 5/16 inch or 8mm drill to allow clearance for the spool mounting bolts. 6. Install the remainder of the hardware and reinstall the bellypan, referring to DIAGRAM B (above). d. e. f. Secure spool attachment bolts with thread-locking compound, e.g. Loctite Blue, not supplied. Page 4 of 5

5 Sport Rear Stand Operation Introduction: The purpose of the large flange on the right side spool is to ease alignment of the left side spool for efficient stand operation. By aligning the right side support plate with the right side spool, the left side support plate and spool become aligned automatically. Operation: Have a spotter available to steady the bike throughout the operation. Refer to images g, h, i at right. 1. While standing on the right-rear side, tip bike off side stand up to vertical using your left hand. 2. Bring stand into place with your right hand and align right side support plate with right side spool. 3. IMPORTANT: Carefully rock bike from side to side to allow support plate and spool to become fully engaged. 4. Verify that left side support plate and left side spool are fully engaged as well. 5. Do not lift bike unless you are sure both support plates have engaged spools. 6. Press down on handle to lift bike. 7. Reverse process to lower bike. g. h. An adhesive-backed clear vinyl sheet may be applied around the lifting spools to help protect the bellypan from scratches during operation. i. When installing or operating the Sport Rear Stand, always have someone nearby assist with the process. If using a front stand together with the rear stand, THE REAR STAND MUST BE PUT IN PLACE FIRST AND REMOVED LAST. Never allow the motorcycle to be supported by a front stand alone. Page 5 of 5