REFERENCE GUIDE INSTRUMENT TRANSFORMERS INDOOR / OUTDOOR CAST RESIN CONSTRUCTION

Transcription

1 REFERENCE GUIDE INSTRUMENT TRANSFORMERS INDOOR / OUTDOOR CAST RESIN CONSTRUCTION

2 CONTENTS The instrument transformers listed in this guide are the most common for the electrical utilities and industries. ARTECHE has a much wider range of characteristics and models. For any different detail than the ones listed, please contact ARTECHE or your local representative/distributor. GENERAL TECHNICAL DATA APPLICATION DATA ACCURACY STANDARDS OTHER INFORMATION 600 V INSTRUMENT TRANSFORMERS 600 V CURRENT TRANSFORMER V VOLTAGE TRANSFORMER 30 Updates available at: 5 kv 34.5 kv INDOOR INSTRUMENT TRANSFORMERS 5 kv VOLTAGE TRANSFORMER kv VOLTAGE TRANSFORMER kv VOLTAGE TRANSFORMER kv VOLTAGE TRANSFORMER kv VOLTAGE TRANSFORMER 60 5 kv CURRENT TRANSFORMER kv CURRENT TRANSFORMER kv CURRENT TRANSFORMER kv CURRENT TRANSFORMER kv CURRENT TRANSFORMER kv COMBINED TRANSFORMER kv COMBINED TRANSFORMER 94 5 kv 69 kv OUTDOOR INSTRUMENT TRANSFORMERS & METERING UNITS 5 kv VOLTAGE TRANSFORMER kv VOLTAGE TRANSFORMER kv VOLTAGE TRANSFORMER kv VOLTAGE TRANSFORMER kv VOLTAGE TRANSFORMER kv VOLTAGE TRANSFORMER kv CURRENT TRANSFORMER kv CURRENT TRANSFORMER kv CURRENT TRANSFORMER kv CURRENT TRANSFORMER kv CURRENT TRANSFORMER kv CURRENT TRANSFORMER kv COMBINED TRANSFORMER AND METERING UNITS kv COMBINED TRANSFORMER AND METERING UNITS kv COMBINED TRANSFORMER AND METERING UNITS 198

3

4 GENERAL TECHNICAL DATA

5 APPLICATION DATA INTRODUCTION The Purpose of instrument transformers: The purpose of instrument transformers is to reduce the voltage and current of an electrical network to standardized, non-hazardous levels. They isolate operators and instruments from the high voltage circuits allowing a less hazardous work environment. Without these transformers, measurements would require expensive insulated instrument panels. There are two types of instrument transformer: transformers (CT: Under normal operating conditions their secondary current is practically proportional to the primary current, and its phase is shifted by an angle close to zero. transformers (VT: Under normal operating conditions the secondary voltage is practically proportional to the primary voltage and its phase is shifted by an angle close to zero. CT A R VT W Figure 1: CT and VT diagram connection R VT VT VOLTAGE DESIGNATIONS Single-phase transformers (UR/UC/UX The U in the type name and the GY in the primary voltage column of the data sheet indicate that the VT has one fully insulated bushing, making it suitable for line-toground connection only /69000GY. This unit is rated for operating Volts. It can be connected at Volts line-to-ground on a Volt system (line-to-line Volts are V /34500GY. This unit is rated for operating Volts. However, it can only be connected line-to-ground on a V system. Therefore, the actual operating voltage of the unit would be 34500/ 3. The accuracy and thermal ratings of this unit are based on V. This is typical where there is a relay connected to the unit which should operate when there is a single lineto-ground fault. In this condition, the line-to-ground voltage becomes equal to the line-to-line voltage. V V R Phase-to-phase transformers (VR/VC/VX The V in the type name and the Y in the primary voltage column of the data sheet indicate that the VT has two fully insulated bushings, making it suitable for line-toline connection /47804Y. This unit is rated for operating Volts. It can be connected at Volts line-toground on a Volt system (line-to-line Volts are V OR it can be connected line-to-line on a system with V line-to-line. This unit is not suitable for operation at Volts /46000Y. This unit is rated for operating Volts. It can be connected at Volts line-to-line. RATING FACTORS Rating factors given in this brochure are standard at 30 C Characteristics for different thermal loadings on request. STANDARDS All the instrument transformers listed in this guide comply with the following standards where applicable: IEEE C Standard Requirements for Instrument transformers. ANSI C American National Standard for Instrument transformers for Revenue Metering 10kV BIL through 350 kv BIL (0.6 kv NSV through 69 kv NSV. CAN/CSA-C Instrument Transformers. IEC Instrument Transformers. HOW TO SPECIFY INSTRUMENT TRANSFORMERS There are several parameters that must be specified when ordering or requesting for proposals or quotations. If the requirements needed fits exactly into the characteristics listed in the data sheets of each model, it is enough to mention the code. However, when non-standard equipment will be needed, the following parameters must be specified: Highest nominal voltage system Basic impulse level (BIL Type of service (outdoor/indoor Frequency Ratio Only for current transformers Continuous thermal current rating factor Short-time thermal current (ka/1s Class and burden Only for voltage transformers Rated continuous voltage Rated voltage factor (30sec Total thermal burden class and burden

6 ACCURACY STANDARDS CURRENT TRANSFORMERS (CT The accuracy class of a current transformer for measuring is given by a number (class rate representing the ratio error limit expressed as a percentage of the rated primary current when the transformer is running at its accuracy load. classes for current transformers are: 0.15S; 0.15; 0.15N; 0.3S; 0.3; 0.6 and 1.2. For class 0.3, 0.6, 0.15N and 1.2 the ratio correction factor must fall within the parallelograms for 100% and 10% respectively. For accuracy class 0.15, 0.15S and 0.3S the ratio correction factor must fall within the parallelograms for 100% and 5% respectively. The following example calculates the correction factor for a current transformer with the following characteristics: 0.3 accuracy class 100% rated current Ratio correction factor: Maximum allowable phase angle: minutes Transformer Correction Factor = RCF (β/2600 = (15.6/2600 = The ratio correction factor and phase angle for any point inside the 0.3 class parallelogram for 100% rated current will always produce a TCF between and VOLTAGE TRANSFORMERS (VT The accuracy class of a voltage transformer for measuring is given by a number (class rate representing the ratio error limit expressed as a percentage of the rated primary voltage when the transformer is running at its accuracy load. classes for voltage transformers are: 0.15; 0.3; 0.6 and 1.2. The following example calculates the correction factor for a voltage transformer with the following characteristics: 0.3 accuracy class 100% rated voltage Ratio correction factor: Maximum allowable phase angle: minutes Transformer Correction Factor = RCF + (γ/2600 = (-15.6/2600 = The ratio correction factor and phase angle for any point inside the 0.3 class parallelogram, will always produce a TCF between and class-100% rated current class- 5% rated current accuracy class parallelogram 0.3 accuracy class parallelogram 0.3 class-100% rated current 0.3 class-10% rated current phase angle minutes-lagging phase angle minutes-leading 0.15 class- 100% rated current 0.15S class- 5% and 100% rated current phase angle minutes-lagging accuracy class parallelogram phase angle minutes-leading to meet 0.3 accuracy class, the ratio and phase angle at the given burden must fall within this parallelogram at 100% rated current and within this parallelogram at 10% rated current ratio correction factor (RCF ratio correction factor (RCF Figure 3: VT Equivalent Parallelogram. Figure 2: CT Equivalent Parallelogram.

7 ACCURACY STANDARDS HIGH ACCURACY EXTENDED RANGE CURRENT TRANSFORMERS Extended range current transformers are designed for modern power generation systems. They accurately measure a wider range of current without making physical changes in the primary or in the secondary connections of a current transformer. To ensure the best performance on nominal primary current readings from 1% to Rating factor (please, see charts below, these current transformers have been designed using magnetic materials that minimize excitation losses and a winding distribution that virtually eliminates stray losses. High accuracy extended range current transformers can increase utility revenue through improved metering. This occurs on systems with variable currents such as wind or solar power generation. In the past, current transformers were designed to accurately measure down to 10% of the current rating on the name plate of the transformer. However, the recent deployment of variable generation has created a need to accurately measure a new range of currents produced by these systems; especially below the rated current of the transformer. Historically, some energy usage revenue went unmeasured. Today Arteche s high accuracy extended range current transformers accurately measure these variable loads. Extended range current transformers answer Standard CT s problem by expanding the amperage load that can be accurately measured. The wider current range helps to reduce the number of different ratios, reducing the amount of inventory needed to respond to customer demands. Standard Class 0.3 means that from 100% of nominal current through the rating factor, accuracy is guaranteed to be ±0.3%, and from 10% of nominal current through 100% of nominal current accuracy is guaranteed to be ±0.6%. 0.6% 0.3% Rated 10% 100% 150% (or Rating Factor High Class 0.15 means that from 100% of nominal current through the rating factor, accuracy is guaranteed to be ±0.15%, and from 5% of nominal current through 100% of nominal current accuracy is guaranteed to be ±0.3%. 0.3% 0.15% Rated 5% 100% 150% (or Rating Factor Class 0.3S means that from 5% of nominal current through the rating factor, accuracy is guaranteed to be ±0.3%. 0.3% Rated 5% 100% 150% (or Rating Factor Class 0.15S means that from 5% of nominal current through the rating factor, accuracy is guaranteed to be ±0.15%. 0.15% Rated 5% 100% 150% (or Rating Factor High, Extended Range Class 0.15 means that from 1% of nominal current through the rating factor, accuracy is guaranteed to be ±0.15%. This goes beyond IEEE C57.13 requirements. 0.15% Rated 1% 5% 100% 150% (or Rating Factor

8 OTHER INFORMATION CURRENT TRANSFORMERS Standard burden 60Hz and 5Amps secondary Burden designation METERING BURDENS Resistance (ohms Inductance (millihenrys Impedance (ohms Volt- Amperes Power factor B B B B B RELAYING BURDENS B B B B VOLTAGE TRANSFORMERS Standard 60Hz Burden designation Volt- Amperes Burden Power Factor W X M Y Z ZZ As per IEEE C , table 19. As per IEEE C , tables 10 and 13. CROSS REFERENCE OF MOST COMMONLY USED TYPES INDOOR transformer transformer ARTECHE GE ABB KUHLMAN ARTECHE GE ABB KUHLMAN CID-17 JKM-5,5A KIR-11 CID-17 U/VCE-17 JVM-4,5 VIZ-11 U/VCD-17 OUTDOOR transformer transformer ARTECHE GE ABB KUHLMAN ARTECHE GE ABB KUHLMAN CRB-17 JCK-5 KOR-11 BB VRL-17 JVW-3 VOY-60 PTT BB & URJ-17 JVW-4,5 VOZ-75 PTT G CRE-17 JKW-3,4 KOR-60,75 BB H VRJ-17 JVW-4,5 VOZ-75 PTT CRE-24 JKW-6 KON-12 BB URN-17 JVW-6 VOG-12 PTT G CRF-24 JKW-6 KOR-15C CRF-36 JKW-7 KOR-20 BB & BB H BB & BB VRN-17 JVW-4,5 VOZ-75 PTT URN-24 JVW-6 VOY-15G PTT G VRN-24 JVW-6 VOY-15 PTT URS-36 JVW-7 VOY-20G PTT G VRS-36 JVW-7C VOY-20 PTT CE-034-E2 JKW-150,200 KOTD-150,200 LG(X URU-52 JVS-250 VOZZ-25G -- CE-046-E2 JKW-250 KOTD-250 CE-046 VRU-52 JVT-250 VOZZ CE-069-E2 JKW CE-069 URU-72 JVS

9 OTHER INFORMATION IT TYPE DESIGNATIONS 5kV - 36kV CT s Indoor VT s Indoor 5kV - 72kV CT s Outdoor VT s outdoor ARTECHE Design 1st position 2nd position 3rd position* 4th&5th position ACA-36 ACD-12, ACD-17, ACD-24 ACI-17 ACH-17, ACH-24 ACF-36 AGPE-12 CID-17 VCE-7, VCE-17 UCE-7, VCE-7 UXI-12 UCI-17 VCL-17, VCL-24 UXL-17 UXL-24 UCJ-24 VCN-36 UXN-36 UEI-24 CRB-17 A=CT Indoor transformer Up to 36 kv with DIN standard A=CT Indoor transformer Up to 36 kv toroidal C=CT Indoor up to 34.5 kv only for America V=Line To Line connection U=line to ground connection U=line to ground connection C=insulation of resin G=insulation resin, window type I=insulation and molded in resin C=insulation and molded in resin. X=insulation and molded in resin with relief valve E=Insulation and molded in resin with metal coated body A=0.3 B0.1 up to B0.5 D=0.3 B0.1 up To B0.9 depending on the ratio I=0.3 B0.5 up To B0.9 depending on the ratio H=0.3 B0.5 up To B1.8 depending on the ratio F=burden B0.5 up To B1.8 depending on the ratio P=Burden B0.1 up to B1.8 C-200 D=0.3 B1.8 C-200 and burden: E=0.3WX, 0.3WXY and burden: I,L,J,N=0.3WXY I=0,3WXY B=0.3B0.5 CRE-17, CRE-24 E=0.3B1.8 T-150 CRF-24, CRF-36 C=CT Outdoor up to R=insulation of F=0.3B1.8 T-200 CRH-36, CRH-52, CRH kv, post type cycloaliphatic resin H=0.3B1.8 T-200 CRK-36, CRK-52, CRK-72 K=0.3B1.8 T-400 CE-034-E2 CE-046-E2 CE-069-E2 VRL-17 URL-17 VRJ-17, VRJ-24 URJ-17 VRN-17, VRN-24 URN-17, URN-24 VRS-36 URS-36 VRU-52 C=CT Outdoor up to 69 kv, top-core with metal coated head V=line To Line connection U=line to ground connection E=Insulation of cycloaliphatic resin and top-core with metal coated head R=insulation Of cycloaliphatic resin 3rd,4th&5th position Insulation level: 034= 34.5/70/200 kv 046= 46/95/250 kv 069= 69/140/350 kv and burden L,J,N,S=0.3WXY URU-52 U=0.3WXYZ URU-72 *The letter in the 3rd position is the size of the CT, each letter means a different size, increasing the size in alphabetical order. Insulation class: 12=8.7/26/75 kv 17=15/34/110 kv 24=25/50/150 kv 36=34.5/70/200 kv E= indoor & outdoor service 12=8.7/26/75 kv Insulation class: 12=8.7/26/75 kv 17=15/34/110 kv 24=25/50/150 kv 36=34.5/70/200 kv 52=46/95/250 kv 72=69/140/350 kv 24=25/50/150 kv Insulation class: 17=15/34/110 kv 24=25/50/150 kv 36=34.5/70/200 kv 52=46/95/250 kv 72=69/140/350 kv 6th position and burden E2=0.3B1.8 T-400 Insulation class: 17= 15/34/110 kv 24=25/50/150 kv 36=34.5/70/200 kv 52=46/95/250 kv 72=69/140/350 kv

10 600 V INSTRUMENT TRANSFORMERS

11 IRH V CURRENT TRANSFORMER ARTECHE IRH series are dry type indoor/outdoor service current transformers. The core is encapsulated with epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. INDOOR 60 Hertz Mechanical characteristics Insulation Material Color Weight (lbs. Resin Brown / Blue Window Type: 5 / Bar Type: 7.3 Window Type: 3.66 ( (80 See table 4 x 5.25 (133 6 ( (86 Drawing number: Bar Type: ø1.40 ( ( ( ( ( (93 Drawing number: ONE SECONDARY PRIMARY TERMINAL SECONDARY TERMINALS AND SHORT CIRCUIT DEVICE MARKING (Single Ratio CONNEC- TIONS ( Type: NEMA2 Material: Copper terminals. Type: Quick Connector Material: Brass Diameter: 1/4 Approximate dimensions in inches (mm. 10

12 IRH V CURRENT TRANSFORMER Electrical characteristics Window type Bar Type No Base Low Base No Base Low Base Window Size Ratio (: (A Continuous Rating 30 C Continuous Rating 55 C IEEE Metering " 200: B " 300: B " 400: B " 600: B " 100: B " 200: B " 200: B " 300: B " 400: B " 500: B " 600: B " 800: B0.5 High Extended Range 5% nominal current to Rating Factor " 600: SB0.2 Additional ratings available upon request. Notes: 11

13 IRH V CURRENT TRANSFORMER ARTECHE IRH series are dry type indoor/outdoor service current transformers. The core is encapsulated with epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. INDOOR-OUTDOOR 60 Hertz The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Mechanical characteristics Insulation Material Color Weight (lbs. Resin Blue ( (79.76 ø3.26 ( ( ( (127 Drawing number: ONE SECONDARY SECONDARY TERMINALS AND SHORT CIRCUIT DEVICE MARKING (Single Ratio CONNEC- TIONS terminals. Type: Quick Connector Material: Brass Diameter: 1/4 Approximate dimensions in inches (mm. 12

14 IRH V CURRENT TRANSFORMER Electrical characteristics Code Ratio (: (A Continuous Rating 30 C Continuous Rating 55 C IEEE Metering Relay : B0.1/1.2B : B0.2/1.2B : B : B0.1/0.6B : B0.2/0.6B1.0 C : B0.5/0.6B2.0 C : B0.5/0.6B2.0 C-10 Additional ratings available upon request. Notes: 13

15 IRH V CURRENT TRANSFORMER ARTECHE IRH series are dry type indoor/outdoor service current transformers. The core is encapsulated with epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. UL Recognized Component INDOOR- OR- OUTDOOR 60 Hertz Mechanical characteristics Insulation Material Color Weight (lbs. Resin Blue Window Type: 10/12 / Bar Type: 15 Window Type: 3.21 ( (116.5 See table 5 (127 Drawing number: Bar Type: 3.21 ( (116.5 See table 9.01 ( (220 5 (127 Drawing number: ONE SECONDARY ONE SECONDARY with tap PRIMARY TERMINAL SECONDARY TERMINALS AND SHORT CIRCUIT DEVICE MARKING (Single Ratio X3 CONNEC- TIONS Type: NEMA2 Material: Copper 2 (51 terminals. Type: Quick Connector Material: Brass Diameter: 1/4 Approximate dimensions in inches (mm. 14

16 IRH V CURRENT TRANSFORMER Electrical characteristics Window type Nema 2 Bar Type Nema 4 Bar Type No Base Low Base No Base Low Base No Base Low Base Window Size Ratio (: (A Continuous Rating 30 C Continuous Rating 55 C IEEE Metering Relay " 50: B " 100: B0.1 C " 200: B0.5 C " 300: B0.5 C " 400: B0.5 C " 500: B0.5 C " 600: B0.5 C " 800: B0.5 C " 1000: B0.5 C " 1200: B1.8 C " 200/400:5 4.0 / / " 300/600:5 3.0 / / " 400/800:5 2.0 / / B0.2 / 0.3 B B0.2 / 0.3 B B0.2 / 0.3 B0.5 High Extended Range 5% nominal current to Rating Factor " 600: S B " 600: S B " 1000: S B0.5 - C-30 / C-50 C-20 / C-40 C-10 / C-30 Additional ratings available upon request. Notes: 15

17 IRH V CURRENT TRANSFORMER ARTECHE IRH series are dry type indoor/outdoor service current transformers. The core is encapsulated with epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. UL Recognized Component INDOOR- OUTDOOR 60 Hertz Mechanical characteristics Insulation Material Color Weight (lbs. Resin Blue Tapered Type: 7.5 / Wide Type: 8.5 Tapered Type: 6.2 ( (77 Drawing number: ( ( ( ( ( (114 Wide Type: Drawing number: ONE SECONDARY SECONDARY TERMINALS AND SHORT CIRCUIT DEVICE MARKING (Single Ratio CONNEC- TIONS terminals. Type: Quick Connector Material: Brass Diameter: 1/4 Approximate dimensions in inches. 16

18 IRH V CURRENT TRANSFORMER Electrical characteristics Code (Tapered type Code (Wide type Ratio (: (A Continuous Rating 30 C Continuous Rating 55 C IEEE Metering Relay : B : B0.1 C : B0.2 C : B0.2 C : B0.5 C : B0.5 C : B0.5 C : B0.5 C : B0.9 C : B0.9 C : B1.8 C : B1.8 C : B1.8 C-10 High Extended Range 5% nominal current to Rating Factor : S B : S B : S B0.5 - Additional ratings available upon request. Notes: 17

19 IRH V CURRENT TRANSFORMER ARTECHE IRH series are dry type indoor/outdoor service current transformers. The core is encapsulated with epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. UL Recognized Component INDOOR- OUTDOOR 60 Hertz Mechanical cal characteristics Insulation Material Color Weight (lbs. Resin Blue (66.5 ø5.5 ( ( ( ( (133 ø8.25 ( (109.5 Drawing number: ONE SECONDARY ONE SECONDARY with tap MARKING (Single Ratio X3 SECONDARY TERMINALS AND SHORT CIRCUIT DEVICE CONNEC- TIONS terminals. Type: Quick Connector Material: Brass Diameter: 1/4 Approximate dimensions in inches (mm. 18

20 IRH V CURRENT TRANSFORMER Electrical characteristics Window type Window plate type Nema 4 Bar Type No Base Low Base No Base Low Base No Base Low Base Ratio (: (A Continuous Continuous Rating Rating 55 C 30 C IEEE Metering Relay : B0.2 C : B : B0.5 C : B0.5 C : B0.5 C : B0.9 C : B0.9 C : B1.8 C : B1.8 C : B /1200:5 3.0/ / B0.2/B0.9 C-10/C /1600:5 3.0/ / B0.2/B1.8 C-30/C /2000:5 3.0/ / B0.5/B1.8 C-30/C /3000:5 2.0/ / B0.9/B1.8 -/C /4000:5 2.0/ / B1.8/B1.8 - High Extended Range 5% nominal current to Rating Factor : S B0.9 - Additional ratings available upon request. Notes: 19

21 IRH V CURRENT TRANSFORMER ARTECHE IRH series are dry type indoor/outdoor service current transformers. The core is encapsulated with epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. UL Recognized Component INDOOR- OUTDOOR 60 Hertz Mechanical characteristics Insulation Material Color Weight (lbs. Resin Blue 19 ø11.38 ( ( ( ( (133 ø8.25 ( (248 Drawing number: ONE SECONDARY ONE SECONDARY with tap MARKING (Single Ratio X3 SECONDARY TERMINALS AND SHORT CIRCUIT DEVICE CONNEC- TIONS terminals. Type: Quick Connector Material: Brass Diameter: 1/4 Approximate dimensions in inches (mm. 20

22 IRH V CURRENT TRANSFORMER Electrical characteristics No Base Window type Low Base Ratio (: (A Continuous Rating 30 C Continuous Rating 55 C IEEE Metering Relay : B0.9 C : B1.8 C : B1.8 C : B1.8 C : B /2000:5 3.0/ / B0.5/B1.8 C-30/C /3000:5 3.0/ / B0.5/B1.8 C-50/C /4000:5 2.0/ / B0.9/B1.8 C-50/C /5000:5 2.0/ / B1.8/B1.8 C-50/C /6000:5 1.33/ / B1.8/B1.8 - High Extended Range 5% nominal current to Rating Factor : S B0.9 - Additional ratings available upon request. Notes: 21

23 ICP V CURRENT TRANSFORMER ARTECHE ICP series are dry type indoor service current transformers. The core is encapsulated with an impact-resistant polycarbonate which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. The core is built with high permeability grain oriented silicon steel laminations for low losses. INDOOR 60 Hertz The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Mechanical characteristics Insulation Material Color Weight (lbs. Polycarbonate Black (90 ø9.9 ( (254 ø6.5 ( ( (35 Drawing number: ONE SECONDARY ONE SECONDARY MULTIRATIO MARKING (Single Ratio X3 X4 X5 Approximate dimensions in inches (mm. 22

24 ICP V CURRENT TRANSFORMER Electrical characteristics Code Window Size Ratio (: (A Continuous Rating 30 C Continuous Rating 55 C IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding " 50: B " 75: B0.2 C " 100: B0.1/2.4B0.2 C " 150: B0.1/1.2B0.2/2.4B0.5 C " 200: B0.2/1.2B0.5/2.4B0.9 C " 250: B0.2/1.2B0.5/2.4B0.9 C " 300: B0.1/0.6B0.2/1.2B0.9/2.4B1.8 C " 400: B0.2/0.6B0.5/1.2B1.8 C " 500: B0.5/0.6B0.9/1.2B1.8 C " 600: B0.5/0.6B1.8 C " 750: B0.9/0.6B1.8 C " 800: B0.9/0.6B1.8 C " 1000: B1.8 C " 1200: B1.8 C " 1500: B1.8 C " 1600: B1.8 C " 2000: B1.8 C " 2500: B1.8 C " 3000: B1.8 C " 3200: B1.8 C " 3500: B1.8 C " 4000: B1.8 C " 5000: B1.8 C " 6000: B1.8 C " 600:5 MR B0.5/0.6B1.8 C " 1200:5 MR B1.8 C " 2000:5 MR B1.8 C " 3000:5 MR B1.8 C " 4000:5 MR B1.8 C Additional ratings available upon request. Notes: 23

25 ICP V CURRENT TRANSFORMER ARTECHE ICP series are dry type indoor service current transformers. The core is encapsulated with an impact-resistant polycarbonate which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. The core is built with high permeability grain oriented silicon steel laminations for low losses. INDOOR 60 Hertz The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Mechanical characteristics Insulation Material Color Weight (lbs. Polycarbonate Black (176 ø6.5 ( (254 ø10 ( ( (35 Drawing number: ONE SECONDARY ONE SECONDARY MULTIRATIO MARKING (Single Ratio X3 X4 X5 Approximate dimensions in inches (mm. 24

26 ICP V CURRENT TRANSFORMER Electrical characteristics Code Window Size Ratio (: (A Continuous Rating 30 C Continuous Rating 55 C IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding " 50: B0.1/4.8B0.2 C " 75: B0.2/2.4B0.5 C " 100: B0.1/1.2B0.2/2.4B0.5 C " 150: B0.2/1.2B0.5/2.4B0.9 C " 200: B0.2/0.6B0.5/1.2B0.9/2.4B1.8 C " 250: B0.2/0.6B0.5/1.2B0.9/2.4B1.8 C " 300: B0.5/0.6B0.9/1.2B1.8 C " 400: B0.5/0.6B1.8 C " 500: B0.9/0.6B1.8 C " 600: B0.9/0.6B1.8 C " 750: B1.8 C " 800: B1.8 C " 1000: B1.8 C " 1200: B1.8 C " 1500: B1.8 C " 1600: B1.8 C " 2000: B1.8 C " 2500: B1.8 C " 3000: B1.8 C " 4000: B1.8 C " 5000: B1.8 C " 6000: B1.8 C " 600:5 MR B0.9/0.6B1.8 C " 1200:5 MR B1.8 C " 2000:5 MR B1.8 C " 3000:5 MR B1.8 C " 4000:5 MR B1.8 C " 5000:5 MR B1.8 C " 6000:5 MR B1.8 C Additional ratings available upon request. Notes: 25

27 OVER BUSHING CURRENT TRANSFORMER 600 V CURRENT TRANSFORMER The ARTECHE Over Bushing CT series are 600 V rated units designed to fit over a variety of specified bushing sizes. current ratios are available from 200:5 thru 5000:5 at 60 Hz with a Rating Factor of up to 4.0. This Slip-Over type CT will operate with high accuracy for metering or relay applications. OUTDOOR 60 Hertz Single, Dual and Multi Ratios, Window Type, Metering/Relaying Mechanical characteristics The core and coil assembly is wound and tape wrapped and is available in window sizes from 2.5 to 45 inches. The secondary leads are typically #10 AWG or #12 AWG. The bushing insulation provides the dielectric protection for the CT. A metal housing covers the whole Transformer. The core of the CT is constructed from high permeability grain oriented silicon steel laminations which provide low core losses. The windings are constructed with copper wire and copper plate double isolation. Concentric distribution of the CT coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses under adverse operating conditions. STAINLESS STEEL BODY (0.59 TERMINALS ø 1/4 GROUND CONNECTION 2 HOLES TO CONDUIT PIPE 1 NPT ALUMINIUM TERMINAL BOX 25º 55º 8x ø 1.18x.59 ø 1/2 -UNC 13 5º 35º 26

28 OVER BUSHING CURRENT TRANSFORMER 600 V CURRENT TRANSFORMER perfomance The ARTECHE Bushing CT provides 0.3 metering class accuracy with burdens from B0.1 to B1.8 and up to class C800 for relay applications. The transformer is accurate through its Rating Factor, and can be used continuously to this level. Testing The ARTECHE Bushing CT is individually tested per the IEEE C57.13 standard, including dielectric tests, accuracy and polarity. Mounting The ARTECHE Bushing CT is designed to be externally mounted around the bushings of power transformers, circuit breakers, underground potheads or in switchgear. Options Through careful calculation, steel selection and testing, existing current transformer characteristics can be matched with the ARTECHE Bushing CT. Existing characteristic curve would be required. Contact factory for other needs. How to order When ordering an ARTECHE Over Bushing CT, include the following information: 1. Minimum inside diameter (ID in [mm] 2. Maximum outside diameter (OD in [mm] 3. Maximum allowable height (HT in [mm] 4. ratio and taps, if any (:5A or :1A SR, DR, MR 5. and burden requirements, for example, Metering - Relaying - If IEC ratings, list class and burden (0.3 B0.1 thru B1.8 (C-100, C-200, C-400, or C-800 or other (e.g., class VA, 5P20-40 VA 6. Continuous Rating Factor (standard is RF= Frequency (standard is 60 Hz 8. Lead length & type, size - (standard is #10 AWG TW NOTE Due to the many variations of mounting, Arteche does not supply mounting hardware. Units are custom manufactured to customer specifications. Contact factory to discuss other options. Notes: 27

29 BUSHING CURRENT TRANSFORMER 600 V CURRENT TRANSFORMER INDOOR 60 Hertz Single, Dual and Multi Ratios, Window Type, Metering/Relaying ARTECHE Bushing CT series are designed to fit over a variety of specified bushing sizes. current ratios are available from 200:5 thru 5000:5 at 60 Hz with a Rating Factor up to 4.0. This tape-wound CT will operate for metering or relaying applications. Mechanical characteristics The core and coil assembly is wound and tape wrapped and is available in window sizes from 2.5 to 45 inches. The secondary leads are typically #10 AWG or #12 AWG. The bushing insulation provides the dielectric protection for the CT. Optional TEFZEL insulation for the CT is also available. The core of the CT is constructed from high permeability grain oriented silicon steel laminations which provide low core losses. The windings are constructed with copper wire and copper plate double insulated. All secondary windings are fully distributed around the core, which provides low leakage reactance on each ratio, achieving greater accuracy and higher capacity to withstand mechanical stresses under adverse operating conditions. NAME PLATE Ø D1 Ø D2 A POLARITY MARK Ø D1 Ø D2 A L =inches WEIGHT lbs. L=inches X3 X4 X5 Specs and dimensions available upon request. Drawing number: TYPE OF CONNECTIONS ( terminal COPPER WIRE AWG FLAT CONNECTION 1/4 COPPER TERMINAL 28

30 BUSHING CURRENT TRANSFORMER 600 V CURRENT TRANSFORMER perfomance The ARTECHE Bushing CT provides 0.3 metering class accuracy with burdens from B0.1 to B1.8 and class C-800 for relaying applications. The transformer is accurate through its Rating Factor for continuous operation. Testing The Arteche Bushing CT is individually tested and certified to IEEE C57.13 or CAN/CSA C Mounting The ARTECHE Bushing CT is designed to be internally mounted around the bushings of power transformers, circuit breakers and switchgear. Features and quality Customized solutions can be developped to satisfy specifical customer needs. Consistent accuracy during the transformer s entire life cycle, providing maximum reliability. ISO 9001:2008 quality system certificate. How to order When ordering an ARTECHE Bushing CT, include the following information: 1. Minimum inside diameter (D2 in 2. Maximum outside diameter (D1 in 3. Maximum allowable height (A in 4. ratio and taps, if any (:5A or :1A Single Ratio, Double Ratio or Multi Ratio 5. and burden requirements, for example, Metering - Relaying - (0.3 B0.1 thru B1.8 or other (C-100, C-200, C-400, or C-800 or other 6. Continuous Rating Factor (standard is RF= Frequency (standard is 60 Hz 8. Lead length & type, size - (standard is #10 AWG 9. Used in or above oil (Yes/No, or in dry surroundings - (Yes/No NOTE Due to the many variations of mounting, Arteche does not supply mounting hardware. Please, don t hesitate to contact us to discuss other options. Notes: 29

31 URC V VOLTAGE TRANSFORMER ARTECHE URC series are dry type indoor/outdoor service voltage transformers. The core is encapsulated with polyurethane which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. INDOOR/OUTDOOR 60 Hertz UL Recognized Component Mechanical characteristics Insulation Material Colors Weight (lbs. Polyurethane Black ( ( ( ( (5 Drawing number: ONE SECONDARY MARKING (Single Ratio Approximate dimensions in inches (mm. 30

32 URC V VOLTAGE TRANSFORMER Electrical characteristics Code Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding :1 115/200Y W, 0.6 X VA :1 120/208Y W VA :1 240/416Y W, 0.6 X VA :1 276/478Y W, 0.6 X VA :1 288/500Y W, 0.6 X VA :1 300/520Y W, 0.6 X VA :1 360/480Y W, 0.6 X VA :1 400/400Y W, 0.6 X VA :1 480/480Y W, 0.6 X VA :1 480/480Y @12.5VA VA :1 500/500Y W, 0.6 X VA :1 600/600Y W, 0.6 X VA :1 600/600Y W, 0.6 X VA Notes: 31

33 URC V VOLTAGE TRANSFORMER ARTECHE URC series are dry type indoor/outdoor service voltage transformers. The core is encapsulated with polyurethane which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. INDOOR/OUTDOOR 60 Hertz UL Recognized Component Mechanical characteristics Insulation Material Colors Weight (lbs. Polyurethane Black ( ( ( ( ( (175.2 Drawing number: ONE SECONDARY MARKING (Single Ratio Approximate dimensions in inches (mm. 32

34 URC V VOLTAGE TRANSFORMER Electrical characteristics Code Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding :1 240/416Y Y VA :1 288/500Y Y VA :1 300/520Y Y VA :1 360/480Y Y VA :1 480/480Y Y VA :1 600/600Y Y VA :1 120/208Y Y VA Notes: 33

35

36 5 kv 34.5 kv INDOOR INSTRUMENT TRANSFORMERS

37 UCE-7 Unfused INDOOR OR 60 Hertz Fused 5 kv VOLTAGE TRANSFORMER ARTECHE UC/UX/VC series are dry type indoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. UL Recognized Component Mechanical characteristics Insulation Material Colors Weight (lbs. Resin Gray* 32 Unfused 3.12 ( (144.3 Nameplate terminals 1/4 -UNC 6.6 ( ( ( ( ( (236.5 Drawing number: Fused 5.68 ( (80.5 Nameplate 8.22 ( ( ( ( (139.7 terminals 1/4 -UNC 8.5 ( (236.5 Drawing number: ONE SECONDARY MARKING (Single Ratio Approximate dimensions in inches (mm. * Brown color available upon request 36

38 UCE-7 5 kv VOLTAGE TRANSFORMER Electrical characteristics Code Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding Switchgear style (no fuse :1 2400/4160GY W,X,M,Y/1.2Z :1 4200/4200GY W,X,M,Y/1.2Z :1 4800/4800GY W,X,M,Y/1.2Z Fuse clips only (no fuse :1 2400/4160GY W,X,M,Y/1.2Z :1 4200/4200GY W,X,M,Y/1.2Z :1 4800/4800GY W,X,M,Y/1.2Z Fuse clips and fuse :1 2400/4160GY W,X,M,Y/1.2Z :1 4200/4200GY W,X,M,Y/1.2Z :1 4800/4800GY W,X,M,Y/1.2Z All units can be supplied either switchgear style, fuse clips only or fuses and clips. Please contact your commercial representant for further information. Additional ratings available upon request. Notes: 37

39 VCE-7 Unfused INDOOR 60 Hertz Fused 5 kv VOLTAGE TRANSFORMER ARTECHE UC/UX/VC series are dry type indoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. UL Recognized Component Mechanical characteristics Unfused Insulation Material Colors Weight (lbs. Resin Gray* (160 5 ( ( (144 Nameplate 6.35 ( (139.7 terminals 1/4 -UNC 8.5 ( (236.5 Drawing number: Fused 5.68 ( (160 5 (127 Nameplate 7.26 ( ( ( ( (139.7 terminals 1/4 -UNC 8.5 ( (236.5 Drawing number: ONE SECONDARY MARKING (Single Ratio Approximate dimensions in inches (mm. * Brown color available upon request 38

40 VCE-7 5 kv VOLTAGE TRANSFORMER Electrical characteristics Code Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding Switchgear style (no fuse :1 2400/4160Y W,X,M,Y/1.2Z :1 4200/4200Y W,X,M,Y/1.2Z :1 4800/4800Y W,X,M,Y/1.2Z Fuse clips only (no fuse :1 2400/4160Y W,X,M,Y/1.2Z :1 4200/4200Y W,X,M,Y/1.2Z :1 4800/4800Y W,X,M,Y/1.2Z Fuse clips and fuse :1 2400/4160Y W,X,M,Y/1.2Z :1 4200/4200Y W,X,M,Y/1.2Z :1 4800/4800Y W,X,M,Y/1.2Z All units can be supplied either switchgear style, fuse clips only or fuses and clips. Please contact your commercial representant for further information. Additional ratings available upon request. Notes: 39

41 UXI kv VOLTAGE TRANSFORMER ARTECHE UC/UX/VC series are dry type indoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. INDOOR 60 Hertz The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. UL Recognized Component Mechanical characteristics Insulation Material Colors Weight (lbs. Resin Gray* ( ( (125 Sealable cover 8.85 (225 terminals 8.07 ( (270.5 Drawing number: ONE SECONDARY MARKING (Single Ratio Approximate dimensions in inches (mm. * Brown color available upon request 40

42 UXI kv VOLTAGE TRANSFORMER Electrical characteristics Code Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding :1 2400/4160GY W,X,M,Y :1 4200/7200GY W,X :1 4800/8320GY W,X :1 7200/12470GY W,X Additional ratings available upon request. Notes: 41

43 UCE kv VOLTAGE TRANSFORMER ARTECHE UC/UX/VC series are dry type indoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. INDOOR 60 Hertz The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. UL Recognized Component Mechanical characteristics Insulation Material Colors Weight (lbs. Resin Gray* 85 Unfused 9.01 ( (189.9 Nameplate terminals 9.83 ( ( ( Drawing number: Fused 9 ( ( Nameplate terminals (314 8 ( ( Drawing number: ONE SECONDARY MARKING (Single Ratio Approximate dimensions in inches (mm. * Brown color available upon request 42

44 UCE kv VOLTAGE TRANSFORMER Electrical characteristics Code Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding Switchgear style (no fuse :1 7200/12470GY W,X,M,Y,Z/1.2ZZ :1 8400/14460GY W,X,M,Y,Z/1.2ZZ : /12000GY W,X,M,Y,Z/1.2ZZ : /13200GY W,X,M,Y,Z/1.2ZZ : /14400GY W,X,M,Y,Z/1.2ZZ Fuse clips only (no fuse :1 7200/12470GY W,X,M,Y,Z/1.2ZZ :1 8400/14460GY W,X,M,Y,Z/1.2ZZ : /12000GY W,X,M,Y,Z/1.2ZZ : /13200GY W,X,M,Y,Z/1.2ZZ : /14400GY W,X,M,Y,Z/1.2ZZ Fuse clips and fuse :1 7200/12470GY W,X,M,Y,Z/1.2ZZ :1 8400/14460GY W,X,M,Y,Z/1.2ZZ : /12000GY W,X,M,Y,Z/1.2ZZ : /13200GY W,X,M,Y,Z/1.2ZZ : /14400GY W,X,M,Y,Z/1.2ZZ All Units can be supplied either switchgear style, fuse clips only or fuses and clips. Please contact your commercial representant for further information. Additional ratings available upon request. Notes: 43

45 UCI kv VOLTAGE TRANSFORMER ARTECHE UC/UX/VC series are dry type indoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. N INDOOR 60 Hertz The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. UL Recognized Component Mechanical characteristics Insulation Material Colors Weight (lbs. Resin Gray* ( ( (125 Sealable cover 8.85 (225 Ground connection terminals 8.07 (205 A (270 Drawing number: ONE SECONDARY MARKING (Single Ratio Approximate dimensions in inches (mm. * Brown color available upon request 44

46 UCI kv VOLTAGE TRANSFORMER Electrical characteristics Code Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding :1 7200/12470GY W,X,M,Y :1 7620/13200GY W,X,M,Y :1 8400/14550GY W,X,M,Y Additional ratings available upon request. Notes: 45

47 UXL kv VOLTAGE TRANSFORMER ARTECHE UC/UX/VC series are dry type indoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. INDOOR 60 Hertz The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. UL Recognized Component Mechanical characteristics Insulation Material Colors Weight (lbs. Resin Gray* ( ( (150 Sealable cover (285 Ground connection terminals (290 Drawing number: ONE SECONDARY MARKING (Single Ratio Approximate dimensions in inches (mm. * Brown color available upon request 46

48 UXL kv VOLTAGE TRANSFORMER Electrical characteristics Code Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding :1 7200/12470GY W,X,M,Y :1 7620/13200GY W,X,M,Y :1 8400/14550GY W,X,M,Y Additional ratings available upon request. Notes: 47

49 VCE kv VOLTAGE TRANSFORMER ARTECHE UC/UX/VC series are dry type indoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. INDOOR 60 Hertz The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. UL Recognized Component Mechanical characteristics Insulation Material Colors Weight (lbs. Resin Gray* (389 Unfused 9.01 ( (235 Nameplate 9.83 ( (333.5 terminals Drawing number: ( ( (235 Nameplate (294 8 (203.2 Fused 8 (203.2 terminals ONE SECONDARY ( Drawing number: MARKING (Single Ratio Approximate dimensions in inches (mm. * Brown color available upon request 48

50 VCE kv VOLTAGE TRANSFORMER Electrical characteristics Code Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding Switchgear style (no fuse :1 7200/12470Y W,X,M,Y,Z/1.2ZZ :1 8400/14460Y W,X,M,Y,Z/1.2ZZ : /12000Y W,X,M,Y,Z/1.2ZZ : /13200Y W,X,M,Y,Z/1.2ZZ : /14400Y W,X,M,Y,Z/1.2ZZ Fuse clips only (no fuse :1 7200/12470Y W,X,M,Y,Z/1.2ZZ :1 8400/14460Y W,X,M,Y,Z/1.2ZZ : /12000Y W,X,M,Y,Z/1.2ZZ : /13200Y W,X,M,Y,Z/1.2ZZ : /14400Y W,X,M,Y,Z/1.2ZZ Fuse clips and fuse :1 7200/12470Y W,X,M,Y,Z/1.2ZZ :1 8400/14460Y W,X,M,Y,Z/1.2ZZ : /12000Y W,X,M,Y,Z/1.2ZZ : /13200Y W,X,M,Y,Z/1.2ZZ : /14400Y W,X,M,Y,Z/1.2ZZ All Units can be supplied either switchgear style, fuse clips only or fuses and clips. Please contact your commercial representant for further information. Additional ratings available upon request. Notes: 49

51 VCL kv VOLTAGE TRANSFORMER ARTECHE UC/UX/VC series are dry type indoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. INDOOR 60 Hertz The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. UL Recognized Component Mechanical characteristics Insulation Material Colors Weight (lbs. Resin Gray* ( ( ( (275 Sealable cover (290 Drawing number: ONE SECONDARY MARKING (Single Ratio Approximate dimensions in inches (mm. * Brown color available upon request 50

52 VCL kv VOLTAGE TRANSFORMER Electrical characteristics Code Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding :1 7200/12470Y W,X,M,Y :1 7620/13200Y W,X,M,Y :1 8400/14450Y W,X,M,Y : /12000Y W,X,M,Y : /13200Y W,X,M,Y : /14400Y W,X,M,Y Additional ratings available upon request. Notes: 51

53 UXL kv VOLTAGE TRANSFORMER ARTECHE UC/UX/VC series are dry type indoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. INDOOR 60 Hertz The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. UL Recognized Component Mechanical characteristics Insulation Material Colors Weight (lbs. Resin Gray* ( ( (150 Sealable cover (285 Ground connection terminals 11.4 (290 Drawing number: ONE SECONDARY MARKING (Single Ratio Approximate dimensions in inches (mm. * Brown color available upon request 52

54 UXL kv VOLTAGE TRANSFORMER Electrical characteristics Code Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : /20750GY W,X,M,Y : /24940GY W,X,M,Y : /24000GY W,X,M,Y Additional ratings available upon request. Notes: 53

55 UCJ kv VOLTAGE TRANSFORMER ARTECHE UC/UX/VC series are dry type indoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. INDOOR 60 Hertz The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. UL Recognized Component Mechanical characteristics Insulation Material Colors Weight (lbs. Resin Gray* (325 7 ( (150 Sealable cover (275 M8 terminals 11 (279 Drawing number: ONE SECONDARY MARKING (Single Ratio Approximate dimensions in inches (mm. * Brown color available upon request 54

56 UCJ kv VOLTAGE TRANSFORMER Electrical characteristics Code Marked Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : /20750GY W,X,M,Y : /24940GY W,X,M,Y : /24000GY W,X,M,Y Additional ratings available upon request. Notes: 55

57 UEI kv VOLTAGE TRANSFORMER ARTECHE UE series are dry type indoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. INDOOR 60 Hertz The entire surface of the transformer is coated with a conductive layer that is intended to be solidly grounded when energized. This allows for compact mounting inside switchgear or enclosures. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. UL Recognized Component Mechanical characteristics Insulation Material Colors Weight (lbs. Resin Gray 62 Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements ( ( (125 Sealable cover (304 terminals 10.8 (274 Drawing number: ONE SECONDARY MARKING (Single Ratio Approximate dimensions in inches (mm. 56

58 UEI kv VOLTAGE TRANSFORMER Electrical characteristics Code Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : /20780GY W,X,M : /24940GY W,X,M Additional ratings available upon request. Notes: 57

59 VCL kv VOLTAGE TRANSFORMER ARTECHE UC/UX/VC series are dry type indoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. INDOOR 60 Hertz The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. UL Recognized Component Mechanical characteristics Insulation Material Colors Weight (lbs. Resin Gray* ( ( ( (276 Terminal secondary Ground connection 9.92 (252 Drawing number: ONE SECONDARY MARKING (Single Ratio Approximate dimensions in inches (mm. * Brown color available upon request 58

60 VCL kv VOLTAGE TRANSFORMER Electrical characteristics Code Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : /20750Y W,X,M,Y : /24940Y W,X,M,Y : /24000Y W,X,M,Y Additional ratings available upon request. Notes: 59

61 UXN kv VOLTAGE TRANSFORMER ARTECHE UC/UX/VC series are dry type indoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. INDOOR 60 Hertz The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. UL Recognized Component Mechanical characteristics Insulation Material Colors Weight (lbs. Resin Gray* ( ( (200 Sealable cover (350 terminals (350 Drawing number: ONE SECONDARY MARKING (Single Ratio Approximate dimensions in inches (mm. * Brown color available upon request 60

62 UXN kv VOLTAGE TRANSFORMER Electrical characteristics Code Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & : /34500GY W,X,M,Y Winding Additional ratings available upon request. Notes: 61

63 UCS-36 Unfused INDOOR OR 60 Hertz Fused 34.5 kv VOLTAGE TRANSFORMER ARTECHE UC/UX/VC series are dry type indoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. UL Recognized Component Mechanical characteristics Insulation Material Colors Weight (lbs. Resin Gray* 167 Unfused ( ( (200 Sealable cover ( (341.8 terminals A 11.8 (230 Drawing number: Fused ( ( (222 Sealable cover ( (457 terminals A 12.8 ( (712 Drawing number: ONE SECONDARY MARKING (Single Ratio Approximate dimensions in inches (mm. * Brown color available upon request 62

64 UCS kv VOLTAGE TRANSFORMER Electrical characteristics Code Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding UNFUSED : /34500GY W,X,M,Y,Z : /34500GY W,X,M,Y,Z : /34500GY W,X,M,Y : /27900GY W,X,M,Y FUSED : /34500GY W,X,M,Y,Z : /34500GY W,X,M,Y,Z : /24000GY W,X,M,Y,Z : /25000GY W,X,M,Y,Z : /26400GY W,X,M,Y,Z : /24900GY W,X,M,Y,Z : /27600GY W,X,M,Y,Z Additional ratings available upon request. Notes: 63

65 VCN kv VOLTAGE TRANSFORMER ARTECHE UC/UX/VC series are dry type indoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. INDOOR 60 Hertz The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. UL Recognized Component Mechanical characteristics Insulation Material Colors Weight (lbs. Resin Gray* ( ( ( (415.5 Terminal secondary Ground connection Sealable cover (350 Drawing number: ONE SECONDARY MARKING (Single Ratio Approximate dimensions in inches (mm. * Brown color available upon request 64

66 VCN kv VOLTAGE TRANSFORMER Electrical characteristics Code Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & : /34500Y W,X,M,Y Additional ratings available upon request. Winding Notes: 65

67 VCS kv VOLTAGE TRANSFORMER Unfused INDOOR OR 60 Hertz Fused ARTECHE UC/UX/VC series are dry type indoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. UL Recognized Component Mechanical characteristics Insulation Material Colors Weight (lbs. Resin Gray* 174 Unfused (410 A Sealable cover ( ( ( (341.8 B (405 terminals Drawing number: ( ( (200 Fused 11.8 (230 Sealable cover (405 terminals 12.8 ( (712 Drawing number: ONE SECONDARY MARKING (Single Ratio Approximate dimensions in inches (mm. * Brown color available upon request 66

68 VCS kv VOLTAGE TRANSFORMER Electrical characteristics Code Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding UNFUSED : /34500Y W,X,M,Y,Z : /27600Y W,X,M,Y,Z : /34500Y W,X,M,Y,Z FUSED : /34500Y W,X,M,Y,Z : /27600Y W,X,M,Y,Z : /34500Y W,X,M,Y,Z Additional ratings available upon request. Notes: 67

69 CID-7 5 kv CURRENT TRANSFORMER ARTECHE AC/CID Series are dry type indoor service current transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. INDOOR 60 Hertz The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial discharge measurements exceed IEEE C requirements. Mechanical characteristics Insulation Material Colors Weight (lbs. Resin Gray * ( ( ( ( (244 2 x 4.25 (2 x (140 2 x 5 (2 x 127 Drawing number: ONE SECONDARY MARKING (Single Ratio Approximate dimensions in inches (mm. * Brown color available upon request 68

70 CID-7 5 kv CURRENT TRANSFORMER Electrical characteristics Code Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Highest Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : B1.8 T : B1.8 T : B1.8 T : B1.8 T : B1.8 T : B1.8 T : B1.8 T : B1.8 T : B1.8 T : B1.8 T : B1.8 T : B1.8 T : B1.8 T : B1.8 T : B1.8 T : B1.8 T : B1.8 T : B1.8 T Additional ratings available upon request. Notes: 69

71 ACD kv CURRENT TRANSFORMER ARTECHE AC series are dry insulated indoor service current transformers. The CT core is encapsulated with Type B epoxy resin resulting in excellent internal dielectric properties and mechanical strength. The device is maintenance free, providing a long mechanical and electrical service life. INDOOR 60 Hertz The core of the CT is constructed from silicon steel laminations with a high permeability grain orientation resulting in low core losses. The windings are copper wire with copper plate double isolation. Concentric distribution of the CT coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses under adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. UL Recognized Component Mechanical characteristics Insulation Material Colors Weight (lbs. Resin Gray* ( ( ( ( ( (140 Sealable cover terminals Drawing number: ONE SECONDARY MARKING (Single Ratio Approximate dimensions in inches (mm. * Brown color available upon request 70

72 ACD kv CURRENT TRANSFORMER Electrical characteristics Code Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C Additional ratings available upon request. Notes: 71

73 AGPE kv CURRENT TRANSFORMER ARTECHE AG Series are dry type indoor service current transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. INDOOR 60 Hertz The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Mechanical characteristics Insulation Material Colors Weight (lbs. Resin Gray* ø11.41 (290 Potential Screw M5 ø14.56 (370 Nameplate 7.99 ( (335 Ground connector Terminal Box 5.11 ( (270 Drawing number: ONE SECONDARY TWO SECONDARIES MARKING (Single Ratio Y1 Y2 Approximate dimensions in inches (mm. * Brown color available upon request 72

74 AGPE kv CURRENT TRANSFORMER Electrical characteristics Code Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : B : C : B : C : B-1.8 C : B-1.8 C : B : B-1.8 C-200, C-200 C-200, C Additional ratings available upon request. Notes: 73

75 ACD kv CURRENT TRANSFORMER ARTECHE AC/CID Series are dry type indoor service current transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. INDOOR 60 Hertz The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. UL Recognized Component Mechanical characteristics Insulation Material Colors Weight (lbs. Resin Gray* ( ( ( (130 Sealable cover ( (140 terminals M6 Drawing number: ONE SECONDARY MARKING (Single Ratio Approximate dimensions in inches (mm. * Brown color available upon request 74

76 ACD kv CURRENT TRANSFORMER Electrical characteristics Code Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C Additional ratings available upon request. Notes: 75

77 ACH kv CURRENT TRANSFORMER ARTECHE AC/CID Series are dry type indoor service current transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. INDOOR 60 Hertz The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. UL Recognized Component Mechanical characteristics Insulation Material Colors Weight (lbs. Resin Gray* (301 7 (177.8 ø1/4 ( ( Nameplate terminals ( (150 Drawing number: ONE SECONDARY MARKING (Single Ratio Approximate dimensions in inches (mm. * Brown color available upon request 76

78 ACH kv CURRENT TRANSFORMER Electrical characteristics Code Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : B-0.5 C : B-0.5 C : B-0.5 C : B-1.0 C : B-1.0 C : B-1.0 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C Additional ratings available upon request. Notes: 77

79 ACI kv CURRENT TRANSFORMER ARTECHE AC/CID Series are dry type indoor service current transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. INDOOR 60 Hertz The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. UL Recognized Component Mechanical characteristics Insulation Material Colors Weight (lbs. Resin Gray* ( ( (125 P2 Ground connector (1/4 8.6 (220 Nameplate terminals P (270.5 Drawing number: ONE SECONDARY MARKING (Single Ratio Approximate dimensions in inches (mm. * Brown color available upon request 78

80 ACI kv CURRENT TRANSFORMER Electrical characteristics Code Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.9 C : B-0.9 C : B-0.9 C : B-0.9 C Additional ratings available upon request. Notes: 79

81 CID kv CURRENT TRANSFORMER ARTECHE AC/CID Series are dry type indoor service current transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. INDOOR 60 Hertz The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. UL Recognized Component Mechanical characteristics Insulation Material Colors Weight (lbs. Resin Gray* ( ( (100 9 ( ( (130 Nameplate 9.63 (245 Drawing number: ONE SECONDARY MARKING (Single Ratio Approximate dimensions in inches (mm. * Brown color available upon request 80

82 CID kv CURRENT TRANSFORMER Electrical characteristics Code Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B : B : B : B : B : B : B : B : B : B : B : B : B : B : B : B : B : B Additional ratings available upon request. 81

83 CID kv CURRENT TRANSFORMER Electrical characteristics Code Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding High Extended Range 5% nominal current to Rating Factor : S B : S B : S B : S B : S B : S B : S B : S B : S B : S B : S B : S B : S B : S B : S B : S B : S B : S B High Extended Range 1% nominal current to Rating Factor : B : B : B : B Additional ratings available upon request. 82

84 CID kv CURRENT TRANSFORMER Notes: 83

85 ACD kv CURRENT TRANSFORMER ARTECHE AC/CID Series are dry type indoor service current transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. INDOOR 60 Hertz The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. UL Recognized Component Mechanical characteristics Insulation Material Colors Weight (lbs. Resin Gray* ( ( ( (130 Sealable cover (255 terminals M6 5.5 (140 Drawing number: ONE SECONDARY MARKING (Single Ratio Approximate dimensions in inches (mm. * Brown color available upon request 84

86 ACD kv CURRENT TRANSFORMER Electrical characteristics Code Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C Additional ratings available upon request. Notes: 85

87 ACH kv CURRENT TRANSFORMER ARTECHE AC/CID Series are dry type indoor service current transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. INDOOR 60 Hertz The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. UL Recognized Component Mechanical characteristics Insulation Material Colors Weight (lbs. Resin Gray* (301 7 (177.8 ø1/4 ( ( Nameplate terminals ( (150 Drawing number: ONE SECONDARY MARKING (Single Ratio Approximate dimensions in inches (mm. * Brown color available upon request 86

88 ACH kv CURRENT TRANSFORMER Electrical characteristics Code Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : B-0.5 C : B-0.5 C : B-0.5 C : B-1.0 C : B-1.0 C : B-1.0 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C High Extended Range 1% nominal current to Rating Factor : B : B : B : B Additional ratings available upon request. Notes: 87

89 ACA kv CURRENT TRANSFORMER ARTECHE AC/CID Series are dry type indoor service current transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. INDOOR 60 Hertz The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. UL Recognized Component Mechanical characteristics Insulation Material Colors Weight (lbs. Resin Gray* ( (170 terminal (377 Connection to ground Sealable cover P (14 P (130 Drawing number: ONE SECONDARY MARKING (Single Ratio Approximate dimensions in inches (mm. * Brown color available upon request 88

90 ACA kv CURRENT TRANSFORMER Electrical characteristics Code Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C : B-0.5 C Additional ratings available upon request. Notes: 89

91 ACF kv CURRENT TRANSFORMER ARTECHE AC/CID Series are dry type indoor service current transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. INDOOR 60 Hertz The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. UL Recognized Component Mechanical characteristics Insulation Material Colors Weight (lbs. Resin Gray* ( ( ( (155 7 (178 terminals Sealable cover Connection to ground ( (353 Drawing number: ONE SECONDARY MARKING (Single Ratio Approximate dimensions in inches (mm. * Brown color available upon request 90

92 ACF kv CURRENT TRANSFORMER Electrical characteristics Code Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C : B-1.8 C Additional ratings available upon request. Notes: 91

93 KCB kv COMBINED TRANSFORMER ARTECHE KCB series are dry type indoor service dead-front combination CT-PT The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. The entire surface of the transformer is coated with a conductive layer that is intended to be solidly grounded when energized. This allows for compact mounting inside switchgear or enclosures. KCB 200 A INDOOR 60 Hertz KCB 600 A The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. The primary terminals are standard 200 or 600 Ampere rated dead-front bushing well and can be connected using IEEE 368 standard inserts and elbow connectors. The secondary terminals are 1/4 slotted screws with flat and lock washers located inside a metallic terminal cover with two 1 NPT conduit hubs. The ground terminal is provided inside the terminal cover along with a manually operated CT secondary shorting device for safety purposes. Mechanical characteristics Insulation Material Colors Weight (lbs. Metallized resin Gray 150 KCB 200 A ( ( (250 Name plate (386 V2 V2 VT CT C1 C2 terminals 1/ hole Ø7/16 to ground connection Terminal box 10 (254 KCB 600 A (503 Drawing number: (200 A / (600 A 3 (76 ONE SECONDARY (466 MARKING (Single Ratio C1 C2 H0 V1 V2 Approximate dimensions in inches (mm. 92

94 KCB kv COMBINED TRANSFORMER Electrical characteristics Code Ratio (: Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering [ Transformer] IEEE Metering [ Transformer] Nominal System (kv BIL (kv Power-Frequency Withstand (1 min Power frequency applied voltage test Power frequency secondary applied voltage test : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z High Extended Range 1% nominal current to Rating Factor : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z Ratings Notes: VT Ratio (V (V Burden (VA Continuous Rated Factor (Un Rated Factor 30s (Un 60:1 7200/12470GY Additional VT ratios are available. Please contact Arteche for details. 93

95 KCB kv COMBINED TRANSFORMER ARTECHE KCB series are dry type indoor service dead-front combination CT-PT The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. The entire surface of the transformer is coated with a conductive layer that is intended to be solidly grounded when energized. This allows for compact mounting inside switchgear or enclosures. KCB 200 A INDOOR 60 Hertz KCB 600 A The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. The primary terminals are standard 200 or 600 Ampere rated dead-front bushing well and can be connected using IEEE 368 standard inserts and elbow connectors. The secondary terminals are 1/4 slotted screws with flat and lock washers located inside a metallic terminal cover with two 1 NPT conduit hubs. The ground terminal is provided inside the terminal cover along with a manually operated CT secondary shorting device for safety purposes. Mechanical characteristics Insulation Material Colors Weight (lbs. Metallized resin Gray 150 KCB 200 A ( ( (250 Name plate (386 V2 V2 VT CT C1 C2 terminals 1/ hole Ø7/16 to ground connection Terminal box 10 (254 KCB 600 A (503 Drawing number: (200 A / (600 A 3 (76 ONE SECONDARY (466 MARKING (Single Ratio C1 H0 C2 V1 V2 Approximate dimensions in inches (mm. 94

96 KCB kv COMBINED TRANSFORMER Electrical characteristics Code Ratio (: Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering [ Transformer] IEEE Metering [ Transformer] Nominal System (kv BIL (kv Power-Frequency Withstand (1 min Power frequency applied voltage test Power frequency secondary applied voltage test : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z High Extended Range 1% nominal current to Rating Factor : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z Ratings Notes: VT Ratio (V (V Burden (VA Continuous Rated Factor (Un Rated Factor 30s (Un 120: /24940GY Additional VT ratios are available. Please contact Arteche for details. 95

97

98 5 kv 69 kv OUTDOOR INSTRUMENT TRANSFORMERS & METERING UNITS

99 VRL-7 5 kv VOLTAGE TRANSFORMER OUTDOOR 60 Hertz ARTECHE UR/VR series are dry type outdoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. Mechanical characteristics (286 The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial discharge measurements exceed IEEE C requirements. Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray * x 8.5 (2 x 216 Terminal box 12 (305 2 x 6.25 (2 x 159 PRIMARY TERMINAL Two holes to conduit pipe A1 - NPT 10.7 (272 GROUND TERMINAL Drawing number: SECONDARY TERMINAL ø1/4 CONNEC- TIONS Type: TE-4T Material: Copper Range: 8SOL-4TRE Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass SINGLE SECONDARY MARKING (Single Ratio Fuse: 16A FUSED UNFUSED Approximate dimensions in inches (mm. * Brown color available upon request 98

100 VRL-7 5 kv VOLTAGE TRANSFORMER Electrical characteristics Code * (CEP Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Highest Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding With FUSE in the secondary box :1 2400/4160Y W,X,M,Y :1 4200/4200Y W,X,M,Y :1 4800/4800Y W,X,M,Y Without FUSE in the secondary box :1 2400/4160Y W,X,M,Y :1 4200/4200Y W,X,M,Y :1 4800/4800Y W,X,M,Y * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request. Notes: 99

101 URJ kv VOLTAGE TRANSFORMER ARTECHE UR/VR series are dry type outdoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. OUTDOOR 60 Hertz The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. Mechanical characteristics The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* / / ( (210 øm12 Nameplate 8.62 ( (453 Lifting holes ø3/4 2 holes to conduit pipe ø1 NPT 10 (254 Drawing number: Fused: / Unfused: PRIMARY TERMINAL GROUND TERMINAL SECONDARY TERMINAL ø1/4 CONNEC- TIONS Type: TE-4T Material: Copper Range: 8SOL-4TRE Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass SINGLE SECONDARY ONE SECONDARY WITH TAP MARKING (Single Ratio Fuse: 16A Fuse: 16A X3 X3 FUSED UNFUSED FUSED UNFUSED Approximate dimensions in inches (mm. * Brown color available upon request 100

102 URJ kv VOLTAGE TRANSFORMER Electrical characteristics Code * (CEP Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding With FUSE in the secondary box :1 2400/4156GY W,X,M,Y /60:1 2400/4156GY & 7200/12470GY W,X / 0.3W,X,M,Y :1 7200/12470GY W,X,M,Y :1 7620/13200GY W,X,M,Y :1 8400/14550GY W,X,M,Y :1 2400/4156GY W,X,M,Y,Z /60:1 2400/4156GY & 7200/12470GY W,X / 0.3W,X,M,Y :1 7200/12470GY W,X,M,Y,Z :1 7620/13200GY W,X,M,Y :1 8400/14550GY W,X,M,Y,Z :1 2400/4156GY W,X,M,Y,Z /60:1 2400/4156GY & 7200/12470GY W,X / 0.3W,X,M,Y :1 7200/12470GY W,X,M,Y,Z :1 7620/13200GY W,X,M,Y :1 8400/14550GY W,X,M,Y,Z Without FUSE in the secondary box :1 2400/4156GY W,X,M,Y :1 7200/12470GY W,X,M,Y :1 7620/13200GY W,X,M,Y :1 8400/14550GY W,X,M,Y :1 2400/4156GY W,X,M,Y,Z :1 7200/12470GY W,X,M,Y,Z :1 7620/13200GY W,X,M,Y :1 8400/14550GY W,X,M,Y,Z * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request. + Extended creepage distance Notes: 101

103 URL kv VOLTAGE TRANSFORMER ARTECHE UR/VR series are dry type outdoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. OUTDOOR 60 Hertz The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. Mechanical characteristics ti The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* ( (204 øm12 Nameplate ( (219 Lifting holes ø3/4 2 holes to conduit pipe ø1 NPT 10 (254 Drawing number: Fused: Unfused: PRIMARY TERMINAL GROUND TERMINAL SECONDARY TERMINAL ø1/4 CONNEC- TIONS Type: TE-4T Material: Copper Range: 8SOL-4TRE Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass SINGLE SECONDARY MARKING (Single Ratio Fuse: 16A FUSED UNFUSED Approximate dimensions in inches (mm. * Brown color available upon request 102

104 URL kv VOLTAGE TRANSFORMER Electrical characteristics Code * (CEP Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding With FUSE in the secondary box :1 2400/4160GY W,X,M,Y :1 4200/7280GY W,X,M,Y :1 4200/4200GY W,X,M,Y :1 5040/8730GY W,X,M,Y :1 7200/12470GY W,X,M,Y :1 7620/13200GY W,X,M,Y :1 7968/13800GY W,X,M,Y :1 8000/13856GY W,X,M,Y :1 8400/14550GY W,X,M,Y :1 2400/4160GY W,X,M,Y :1 4200/7280GY W,X,M,Y :1 4200/4200GY W,X,M,Y :1 5040/8730GY W,X,M,Y :1 7200/12470GY W,X,M,Y :1 7620/13200GY W,X,M,Y :1 7968/13800GY W,X,M,Y :1 8000/13856GY W,X,M,Y :1 8400/14550GY W,X,M,Y Without FUSE in the secondary box :1 2400/4160GY W,X,M,Y :1 4200/7280GY W,X,M,Y :1 4200/4200GY W,X,M,Y :1 5040/8730GY W,X,M,Y :1 7200/12470GY W,X,M,Y :1 7620/13200GY W,X,M,Y :1 7968/13800GY W,X,M,Y :1 8000/13856GY W,X,M,Y :1 8400/14550GY W,X,M,Y :1 2400/4160GY W,X,M,Y :1 4200/7280GY W,X,M,Y :1 4200/4200GY W,X,M,Y :1 5040/8730GY W,X,M,Y :1 7200/12470GY W,X,M,Y :1 7620/13200GY W,X,M,Y :1 7968/13800GY W,X,M,Y :1 8000/13856GY W,X,M,Y :1 8400/14550GY W,X,M,Y * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request

105 URN kv VOLTAGE TRANSFORMER ARTECHE UR/VR series are dry type outdoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. OUTDOOR 60 Hertz The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. Mechanical characteristics The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* (205 øm12 Nameplate 8.6 ( (485 Lifting holes ø3/4 2 holes to conduit pipe ø1 NPT 10 (254 Drawing number: Fused: Unfused: PRIMARY TERMINAL GROUND TERMINAL SECONDARY TERMINAL ø1/4 CONNEC- TIONS Type: TE-4T Material: Copper Range: 8SOL-4TRE Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass SINGLE SECONDARY ONE SECONDARY WITH TAP MARKING (Single Ratio Fuse: 16A Fuse: 16A X3 X3 FUSED UNFUSED FUSED UNFUSED Approximate dimensions in inches (mm. * Brown color available upon request 104

106 URN kv VOLTAGE TRANSFORMER Electrical characteristics Code * (CEP Ratio With FUSE in the secondary box /60:1 (V 2400/4156GY & 7200/12470GY (V /112.88:1 7620/13200GY 115/ /60:1 2400/4156GY & 7200/12470GY /112.88:1 7620/13200GY 115/67.5 Without FUSE in the secondary box /60:1 2400/4156GY & 7200/12470GY /112.88:1 7620/13200GY 115/ /60:1 2400/4156GY & 7200/12470GY /112.88:1 7620/13200GY 115/67.5 IEEE Metering 0.3 W,X/ 0.3 W,X,M,Y 0.3 W,X,M,Y/ 0.6 W,X,M,Y 0.3 W,X/ 0.3 W,X,M,Y 0.3 W,X,M,Y/ 0.6 W,X,M,Y 0.3 W,X/ 0.3 W,X,M,Y 0.3 W,X,M,Y/ 0.6 W,X,M,Y 0.3 W,X/ 0.3 W,X,M,Y 0.3 W,X,M,Y/ 0.6 W,X,M,Y Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request. Notes: 105

107 VRJ kv VOLTAGE TRANSFORMER OUTDOOR 60 Hertz ARTECHE UR/VR series are dry type outdoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. Mechanical characteristics The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* ( (210 Nameplate (450 Lifting holes ø3/ (219 2 holes to conduit pipe ø1 NPT 10 (254 Drawing number: Fused: Unfused: PRIMARY TERMINAL GROUND TERMINAL SECONDARY TERMINAL ø1/4 CONNEC- TIONS Type: TE-4T Material: Copper Range: 8SOL-4TRE Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass SINGLE SECONDARY ONE SECONDARY WITH TAP MARKING (Single Ratio Fuse: 16A Fuse: 16A X3 X3 FUSED UNFUSED FUSED UNFUSED Approximate dimensions in inches (mm. * Brown color available upon request 106

108 VRJ kv VOLTAGE TRANSFORMER Electrical characteristics Code * (CEP Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding With FUSE in the secondary box :1 2400/4160Y W,X,M,Y :1 3600/3600Y W,X,M,Y :1 4200/4200Y W,X,M,Y :1 4800/4800Y W,X,M,Y :1 7200/12470Y W,X,M,Y :1 7620/13200Y W,X,M,Y :1 8400/14550Y W,X,M,Y /121.21:1 8400/14550Y & 14545/14545Y W,X,M,Y : /12000Y W,X,M,Y : /13200Y W,X,M,Y : /14400Y W,X,M,Y :1 8400/14550Y W,X : /12000Y W,X : /13200Y W,X : /14400Y W,X :1 2400/4160Y W,X,M,Y,Z :1 3600/3600Y W,X,M,Y,Z :1 4200/4200Y W,X,M,Y.Z :1 4800/4800Y W,X,M,Y,Z :1 7200/12470Y W,X,M,Y,Z :1 7620/13200Y W,X,M,Y,Z :1 8400/14550Y W,X,M,Y,Z /121.21:1 8400/14550Y & 14545/14545Y W,X,M,Y,Z : /12000Y W,X,M,Y,Z : /13200Y W,X,M,Y,Z : /14400Y W,X,M,Y,Z :1 8400/14550Y W,X,M,Y : /12000Y W,X,M,Y : /13200Y W,X,M,Y : /14400Y W,X,M,Y

109 VRJ kv VOLTAGE TRANSFORMER Electrical characteristics Code * (CEP Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding Without FUSE in the secondary box :1 2400/4160Y W,X,M,Y :1 3600/3600Y W,X,M,Y :1 4200/4200Y W,X,M,Y :1 4800/4800Y W,X,M,Y :1 7200/12470Y W,X,M,Y :1 7620/13200Y W,X,M,Y :1 8400/14550Y W,X,M,Y : /12000Y W,X,M,Y : /13200Y W,X,M,Y : /14400Y W,X,M,Y :1 2400/4160Y W,X,M,Y,Z :1 3600/3600Y W,X,M,Y,Z :1 4200/4200Y W,X,M,Y.Z :1 4800/4800Y W,X,M,Y,Z :1 7200/12470Y W,X,M,Y,Z :1 7620/13200Y W,X,M,Y,Z :1 8400/14550Y W,X,M,Y,Z : /12000Y W,X,M,Y,Z : /13200Y W,X,M,Y,Z : /14400Y W,X,M,Y,Z * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request

110 VRJ kv VOLTAGE TRANSFORMER Notes: 109

111 ØM12 VRL kv VOLTAGE TRANSFORMER OUTDOOR 60 Hertz ARTECHE UR/VR series are dry type outdoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. Mechanical characteristics The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* ( (204 Nameplate 8.62 ( (450 Lifting holes ø3/4 2 holes to conduit pipe ø1 NPT 10 (254 Drawing number: Fused: Unfused: PRIMARY TERMINAL GROUND TERMINAL SECONDARY TERMINAL ø1/4 CONNEC- TIONS Type: TE-4T Material: Copper Range: 8SOL-4TRE Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass SINGLE SECONDARY MARKING (Single Ratio Fuse: 16A FUSED UNFUSED Approximate dimensions in inches (mm. * Brown color available upon request 110

112 VRL kv VOLTAGE TRANSFORMER Electrical characteristics Code * (CEP Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding With FUSE in the secondary box :1 2400/4160Y W,X,M,Y :1 4200/4200Y W,X,M,Y :1 4800/4800Y W,X,M,Y :1 5040/5040Y W,X,M,Y :1 7200/12470Y W,X,M,Y :1 7620/13200Y W,X,M,Y :1 7920/13700Y W,X,M,Y :1 8400/14550Y W,X,M,Y : /12000Y W,X,M,Y : /13200Y W,X,M,Y : /13800Y W,X,M,Y : /14400Y W,X,M,Y :1 2400/4160Y W,X,M,Y :1 4200/4200Y W,X,M,Y :1 4800/4800Y W,X,M,Y :1 5040/5040Y W,X,M,Y :1 7200/12470Y W,X,M,Y :1 7620/13200Y W,X,M,Y :1 7920/13700Y W,X,M,Y :1 8400/14550Y W,X,M,Y : /12000Y W,X,M,Y : /13200Y W,X,M,Y : /13800Y W,X,M,Y : /14400Y W,X,M,Y

113 VRL kv VOLTAGE TRANSFORMER Electrical characteristics Code * (CEP Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding Without FUSE in the secondary box :1 2400/4160Y W,X,M,Y :1 4200/4200Y W,X,M,Y :1 4800/4800Y W,X,M,Y :1 5040/5040Y W,X,M,Y :1 7200/12470Y W,X,M,Y :1 7620/13200Y W,X,M,Y :1 7920/13700Y W,X,M,Y :1 8400/14550Y W,X,M,Y : /12000Y W,X,M,Y : /13200Y W,X,M,Y : /13800Y W,X,M,Y : /14400Y W,X,M,Y :1 2400/4160Y W,X,M,Y :1 4200/4200Y W,X,M,Y :1 4800/4800Y W,X,M,Y :1 5040/5040Y W,X,M,Y :1 7200/12470Y W,X,M,Y :1 7620/13200Y W,X,M,Y :1 7920/13700Y W,X,M,Y :1 8400/14550Y W,X,M,Y : /12000Y W,X,M,Y : /13200Y W,X,M,Y : /13800Y W,X,M,Y : /14400Y W,X,M,Y * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request

114 VRL kv VOLTAGE TRANSFORMER Notes: 113

115 VRN kv VOLTAGE TRANSFORMER ARTECHE UR/VR series are dry type outdoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. OUTDOOR 60 Hertz The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. Mechanical characteristics The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* ( (205 øm12 Nameplate 19 (485 Lifting holes ø3/4 8.6 (219 2 holes to conduit pipe ø1 NPT 10 (254 Drawing number: Fused: Unfused: PRIMARY TERMINAL GROUND TERMINAL SECONDARY TERMINAL ø1/4 CONNEC- TIONS Type: TE-4T Material: Copper Range: 8SOL-4TRE Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass SINGLE SECONDARY ONE SECONDARY WITH TAP MARKING (Single Ratio Fuse: 16A Fuse: 16A X3 X3 FUSED UNFUSED FUSED UNFUSED Approximate dimensions in inches (mm. * Brown color available upon request 114

116 VRN kv VOLTAGE TRANSFORMER Electrical characteristics Code * (CEP Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding With FUSE in the secondary box :1 2400/4160Y W,X,M,Y :1 3600/3600Y W,X,M,Y :1 4200/4200Y W,X,M,Y :1 4800/4800Y W,X,M,Y :1 7200/12470Y W,X,M,Y :1 7620/13200Y W,X,M,Y :1 8400/14550Y W,X,M,Y /121.2:1 8400/14550Y & 14545/14545Y W,X,M,Y : /12000Y W,X,M,Y : /13200Y W,X,M,Y : /14400Y W,X,M,Y :1 2400/4160Y W,X,M,Y,Z :1 3600/3600Y W,X,M,Y,Z :1 4200/4200Y W,X,M,Y,Z :1 4800/4800Y W,X,M,Y,Z :1 7200/12470Y W,X,M,Y,Z :1 7620/13200Y W,X,M,Y,Z :1 8400/14550Y W,X,M,Y,Z /121.2:1 8400/14550Y & 14545/14545Y W,X,M,Y,Z : /12000Y W,X,M,Y,Z : /13200Y W,X,M,Y,Z : /14400Y W,X,M,Y,Z Without FUSE in the secondary box :1 2400/4160Y W,X,M,Y :1 3600/3600Y W,X,M,Y :1 4200/4200Y W,X,M,Y :1 4800/4800Y W,X,M,Y :1 7200/12470Y W,X,M,Y :1 7620/13200Y W,X,M,Y :1 8400/14550Y W,X,M,Y : /12000Y W,X,M,Y : /13200Y W,X,M,Y : /14400Y W,X,M,Y :1 2400/4160Y W,X,M,Y,Z :1 3600/3600Y W,X,M,Y,Z :1 4200/4200Y W,X,M,Y,Z :1 4800/4800Y W,X,M,Y,Z :1 7200/12470Y W,X,M,Y,Z :1 7620/13200Y W,X,M,Y,Z :1 8400/14550Y W,X,M,Y,Z : /12000Y W,X,M,Y,Z : /13200Y W,X,M,Y,Z : /14400Y W,X,M,Y,Z * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request

117 URJ kv VOLTAGE TRANSFORMER OUTDOOR 60 Hertz ARTECHE UR/VR series are dry type outdoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. Mechanical characteristics Insulation Material Colors Weight (lbs. Resin Gray* 93 The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements ( (210 øm12 Nameplate 21 (533.4 Lifting holes ø3/ (219 2 holes to conduit pipe ø1 NPT 10 (254 Drawing number: Fused: Unfused: PRIMARY TERMINAL GROUND TERMINAL SECONDARY TERMINAL ø1/4 CONNEC- TIONS Type: TE-4T Material: Copper Range: 8SOL-4TRE Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass SINGLE SECONDARY MARKING (Single Ratio Fuse: 16A FUSED UNFUSED Approximate dimensions in inches (mm. * Brown color available upon request 116

118 URJ kv VOLTAGE TRANSFORMER Electrical characteristics Code * (CEP Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding With FUSE in the secondary box :1 7200/12470GY W,X,M,Y : /20780GY W,X,M,Y : /20780GY W,X : /22860GY W,X,M,Y : /22863GY W,X : /24940GY W,X,M,Y : /24250GY W,X : /18000GY W,X,M,Y : /18000GY W,X : /24000GY W,X,M,Y : /24000GY W,X Without FUSE in the secondary box :1 7200/12470GY W,X,M,Y : /20780GY W,X,M,Y : /22860GY W,X,M,Y : /24940GY W,X,M,Y : /18000GY W,X,M,Y : /24000GY W,X,M,Y * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request. Notes: 117

119 URN kv VOLTAGE TRANSFORMER OUTDOOR 60 Hertz ARTECHE UR/VR series are dry type outdoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. Mechanical characteristics The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* ( (205 øm12 Nameplate (530 Lifting holes ø3/4 8.6 (219 2 holes to conduit pipe ø1 NPT 10 (254 Drawing number: Fused: Unfused: PRIMARY TERMINAL GROUND TERMINAL SECONDARY TERMINAL ø1/4 CONNEC- TIONS Type: TE-4T Material: Copper Range: 8SOL-4TRE Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass SINGLE SECONDARY ONE SECONDARY WITH TAP MARKING (Single Ratio Fuse: 16A Fuse: 16A X3 X3 FUSED UNFUSED FUSED UNFUSED Approximate dimensions in inches (mm. * Brown color available upon request 118

120 URN kv VOLTAGE TRANSFORMER Electrical characteristics Code * (CEP Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding With FUSE in the secondary box : /20784GY W,X,M,Y : /22863GY W,X,M,Y : /24940GY W,X,M,Y /120:1 7200/12470GY & 14400/24940GY W,X / 0.3W,X,M,Y /200: /24940GY 120/ W,X,M,Y : /20784GY W,X,M,Y : /22863GY W,X,M,Y : /24940GY W,X,M,Y /120:1 7200/12470GY & 14400/24940GY W,X / 0.3W,X,M,Y /200: /24940GY 120/ W,X,M,Y Without FUSE in the secondary box : /20784GY W,X,M,Y : /22863GY W,X,M,Y : /24940GY W,X,M,Y /200: /24940GY 120/ W,X,M,Y : /20784GY W,X,M,Y : /22863GY W,X,M,Y : /24940GY W,X,M,Y /200: /24940GY 120/ W,X,M,Y * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request. Notes: 119

121 VRJ kv VOLTAGE TRANSFORMER OUTDOOR 60 Hertz ARTECHE UR/VR series are dry type outdoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. Mechanical characteristics The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* (320 øm (210 Nameplate ( (219 2 holes to conduit pipe ø1 NPT 10 (254 Drawing number: Fused: Unfused: PRIMARY TERMINAL GROUND TERMINAL SECONDARY TERMINAL ø1/4 CONNEC- TIONS Type: TE-4T Material: Copper Range: 8SOL-4TRE Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass SINGLE SECONDARY MARKING (Single Ratio Fuse: 16A FUSED UNFUSED Approximate dimensions in inches (mm. * Brown color available upon request 120

122 VRJ kv VOLTAGE TRANSFORMER Electrical characteristics Code * (CEP Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding With FUSE in the secondary box :1 7200/12470Y W,X,M,Y : /20780Y W,X,M,Y : /20780Y W,X : /22860Y W,X,M,Y : /22860Y W,X : /24940Y W,X,M,Y : /24250Y W,X : /18000Y W,X,M,Y : /18000Y W,X : /24000Y W,X,M,Y : /24000Y W,X Without FUSE in the secondary box :1 7200/12470Y W,X,M,Y : /20780Y W,X,M,Y : /22860Y W,X,M,Y : /24940Y W,X,M,Y : /18000Y W,X,M,Y : /24000Y W,X,M,Y * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request. Notes: 121

123 VRN kv VOLTAGE TRANSFORMER ARTECHE UR/VR series are dry type outdoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. OUTDOOR 60 Hertz The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Mechanical characteristics Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* ( (205 øm12 Nameplate (527 Lifting holes ø3/4 8.6 (219 2 holes to conduit pipe ø1 NPT 10 (254 Drawing number: Fused: Unfused: PRIMARY TERMINAL GROUND TERMINAL SECONDARY TERMINAL ø1/4 CONNEC- TIONS Type: TE-4T Material: Copper Range: 8SOL-4TRE Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass SINGLE SECONDARY ONE SECONDARY WITH TAP MARKING (Single Ratio Fuse: 16A Fuse: 16A X3 X3 FUSED UNFUSED FUSED UNFUSED Approximate dimensions in inches (mm. * Brown color available upon request 122

124 VRN kv VOLTAGE TRANSFORMER Electrical characteristics Code * (CEP Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding With FUSE in the secondary box :1 7200/12470Y W,X,M,Y /120:1 7200/12470Y & 14400/24940Y W,X / 0.3W,X,M,Y : /20780Y W,X,M,Y : /22860Y W,X,M,Y : /24940Y W,X,M,Y /200: /24250Y 120/ W,X,M,Y / 0.3 W,X,M,Y : /18000Y W,X,M,Y : /24000Y W,X,M,Y : /20780Y W,X : /22860Y W,X : /24250Y W,X : /18000Y W,X : /24000Y W,X :1 7200/12470Y W,X,M,Y /120:1 7200/12470Y & 14400/24940Y W,X / 0.3W,X,M,Y : /20780Y W,X,M,Y : /22860Y W,X,M,Y : /24940Y W,X,M,Y /200: /24250Y 120/ W,X,M,Y / 0.3 W,X,M,Y : /18000Y W,X,M,Y : /24000Y W,X,M,Y : /20780Y W,X : /22860Y W,X : /18000Y W,X Without FUSE in the secondary box :1 7200/12470Y W,X,M,Y : /20780Y W,X,M,Y : /22860Y W,X,M,Y : /24940Y W,X,M,Y : /18000Y W,X,M,Y : /24000Y W,X,M,Y :1 7200/12470Y W,X,M,Y : /20780Y W,X,M,Y : /22860Y W,X,M,Y : /24940Y W,X,M,Y : /18000Y W,X,M,Y : /24000Y W,X,M,Y * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request

125 URS kv VOLTAGE TRANSFORMER ARTECHE UR/VR series are dry type outdoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. OUTDOOR 60 Hertz The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. Mechanical characteristics The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* (240 øm ( Lifting holes ø3/ (200 2 holes to conduit pipe ø1 NPT 13.7 (350 Drawing number: Fused: Unfused: PRIMARY TERMINAL GROUND TERMINAL SECONDARY TERMINAL ø1/4 CONNEC- TIONS Type: TE-4T Material: Copper Range: 8SOL-4TRE Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass SINGLE SECONDARY ONE SECONDARY WITH TAP MARKING (Single Ratio Fuse: 16A Fuse: 16A X3 X3 FUSED UNFUSED FUSED UNFUSED Approximate dimensions in inches (mm. * Brown color available upon request 124

126 URS kv VOLTAGE TRANSFORMER Electrical characteristics Code * (CEP Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding With FUSE in the secondary box : /29098GY W,X,M,Y /240: /27886GY 115/ W,X,M,Y : /34500GY W,X,M,Y : /34857GY W,X,M,Y /300: /34857GY 115/ W,X,M,Y Without FUSE in the secondary box : /29098GY W,X,M,Y /240: /27886GY 115/ W,X,M,Y : /34500GY W,X,M,Y : /34857GY W,X,M,Y /300: /34857GY 115/ W,X,M,Y * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request. Notes: 125

127 URU kv VOLTAGE TRANSFORMER ARTECHE UR/VR series are dry type outdoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. OUTDOOR 60 Hertz The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. Mechanical characteristics The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* ( ( ( ( X (2 X 400 Drawing number: PRIMARY TERMINAL GROUND TERMINAL SECONDARY TERMINAL ø1/4 CONNEC- TIONS Type: TE-4T Material: Copper Range: 8SOL-4TRE Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass SINGLE SECONDARY ONE SECONDARY WITH TAP TWO SECONDARY WITH TAP MARKING (Single Ratio X3 X3 Y1 Y2 Y3 Approximate dimensions in inches (mm. * Brown color available upon request 126

128 URU kv VOLTAGE TRANSFORMER Electrical characteristics Code * (CEP Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : /34857GY W,X,M,Y,Z,ZZ /300: /34857GY 115/ W,X,M,Y,Z & * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request. Notes: 127

129 VRS kv VOLTAGE TRANSFORMER ARTECHE UR/VR series are dry type outdoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. OUTDOOR 60 Hertz The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. Mechanical characteristics The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* ( (240 øm12 Nameplate (695 Lifting holes ø3/ (200 2 holes to conduit pipe ø1 NPT 13.7 (350 Drawing number: Fused: Unfused: PRIMARY TERMINAL GROUND TERMINAL SECONDARY TERMINAL ø1/4 CONNEC- TIONS Type: TE-4T Material: Copper Range: 8SOL-4TRE Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass SINGLE SECONDARY ONE SECONDARY WITH TAP MARKING (Single Ratio Fuse: 16A Fuse: 16A X3 X3 FUSED UNFUSED FUSED UNFUSED Approximate dimensions in inches (mm. * Brown color available upon request 128

130 VRS kv VOLTAGE TRANSFORMER Electrical characteristics Code * (CEP Ratio (V With FUSE in the secondary box / 166:1 8310/14393Y & 19920/34500Y (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding W,X,M,Y : /29098Y W,X,M,Y /240: /27886Y 115/ W,X,M,Y : /34500Y W,X,M,Y : /34857Y W,X,M,Y /300: /34857Y 115/ W,X,M,Y : /26400Y W,X,M,Y,Z /400: /27600Y 115 / W,X,M,Y : /34500Y W,X,M,Y,Z /500: /34500Y 115/ W,X,M,Y : /29098Y W,X : /34500Y W,X : /34500Y W,X : /26400Y W,X : /34500Y W,X Without FUSE in the secondary box / 166:1 8310/14393Y & 19920/34500Y W,X,M,Y : /29098Y W,X,M,Y /240: /27886Y 115/ W,X,M,Y : /34500Y W,X,M,Y : /34857Y W,X,M,Y /300: /34857Y 115/ W,X,M,Y : /26400Y W,X,M,Y,Z /400: /27600Y 115 / W,X,M,Y : /34500Y W,X,M,Y,Z /500: /34500Y 115/ W,X,M,Y * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request. Notes: 129

131 VRU kv VOLTAGE TRANSFORMER ARTECHE UR/VR series are dry type outdoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. OUTDOOR 60 Hertz The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments (440 The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Mechanical characteristics Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* ( ( X (2 X (2 X (612 2 X (2 X 400 Drawing number: PRIMARY TERMINAL GROUND TERMINAL SECONDARY TERMINAL ø1/4 CONNEC- TIONS Type: TE-4T Material: Copper Range: 8SOL-4TRE Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass ONE SECONDARY TWO SECONDARIES ONE SECONDARY WITH TAP TWO SECONDARIES WITH TAP MARKING (Single Ratio X3 X3 Y1 Y2 Y1 Y2 Y3 Approximate dimensions in inches (mm. * Brown color available upon request 130

132 VRU kv VOLTAGE TRANSFORMER Electrical characteristics Code * (CEP Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & : /34857Y W,X,M,Y,Z,ZZ VA Winding : /34857Y 115 & W,X,M,Y,Z & 1250 VA : /23000Y W,X,M,Y,Z,ZZ VA : /27600Y 115 & W,X,M,Y,Z & 1250 VA : /34500Y 115 & W,X,M,Y,Z & 1250 VA /300: /34857Y 115/ W,X,M,Y,Z VA /500: /34500Y 115/ W,X,M,Y,Z VA /300: /34857Y 115/67.08 & 115/ /300 & 300/520: / /67.08 & 115/66.36 * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request. Notes: 0.3 W,X,M,Y,Z W,X,M,Y,Z & 1250 VA 1000 & 1000 VA

133 URU kv VOLTAGE TRANSFORMER ARTECHE UR/VR series are dry type outdoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. OUTDOOR 60 Hertz The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. Mechanical characteristics The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* (435 øm ( ( (500 Drawing number: PRIMARY TERMINAL GROUND TERMINAL SECONDARY TERMINAL ø1/4 CONNEC- TIONS Type: TE-4T Material: Copper Range: 8SOL-4TRE Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass ONE SECONDARY TWO SECONDARIES ONE SECONDARY WITH TAP TWO SECONDARIES WITH TAP MARKING (Single Ratio X3 X3 Y1 Y2 Y1 Y2 Y3 Approximate dimensions in inches (mm. * Brown color available upon request 132

134 URU kv VOLTAGE TRANSFORMER Electrical characteristics Code * (CEP Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & : /47804GY W,X,M,Y,Z,ZZ & 240: /47804GY 115 & W,X,M,Y,Z & 0.3 W,X,M,Y,Z & 1250 Winding /400: /47804GY 115/ W,X,M,Y,Z : /47804GY W,X,M,Y,Z /400 & 240/400: /47804GY 115/69 & 115/69 * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request. 0.3 W,X,M,Y,Z & 0.3 W,X,M,Y,Z & Notes: 133

135 VRU kv VOLTAGE TRANSFORMER ARTECHE UR/VR series are dry type outdoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. OUTDOOR 60 Hertz The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. Mechanical characteristics 24 ( (435 øm12 The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* ( ( (500 Drawing number: PRIMARY TERMINAL GROUND TERMINAL SECONDARY TERMINAL ø1/4 CONNEC- TIONS Type: TE-4T Material: Copper Range: 8SOL-4TRE Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass ONE SECONDARY TWO SECONDARIES ONE SECONDARY WITH TAP TWO SECONDARIES WITH TAP MARKING (Single Ratio X3 X3 Y1 Y2 Y1 Y2 Y3 Approximate dimensions in inches (mm. * Brown color available upon request 134

136 VRU kv VOLTAGE TRANSFORMER Electrical characteristics Code * (CEP Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & : /47804Y W,X,M,Y,Z,ZZ & 240: /47804Y 115 & W,X,M,Y,Z & 0.3 W,X,M,Y,Z & 1500 Winding /400: /47804Y 115/ W,X,M,Y,Z : /46000Y W,X,M,Y,Z,ZZ & 400: /46000Y 115 & W,X,M,Y,Z & 0.3 W,X,M,Y,Z & /666.66: /46000Y 115/ W,X,M,Y,Z : /47804Y W,X,M,Y,Z /400: /47804Y 115/ W,X,M,Y : /46000Y W,X,M,Y,Z * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request. Notes: 135

137 URU kv VOLTAGE TRANSFORMER OUTDOOR 60 Hertz ARTECHE UR/VR series are dry type outdoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. Mechanical characteristics The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* terminal pad NEMA 4 STD Thread 1/ (435 Connector TE-250 Lifting holes ø3/4 2 holes to conduit pipe ø1 NPT (1228 Nameplate ( (500 Drawing number: PRIMARY TERMINAL GROUND TERMINAL CONNEC- TIONS Type: TE-250 Material: Copper Range: 2/0 TRE-250MCM Type: NEMA-2 Material: Copper Type: NEMA-4 Material: Copper Type: TE Material: Copper Range: 4TRE-250MCM SECONDARY TERMINAL ø1/4 MARKING (Single Ratio ONE SECONDARY TWO SECONDARIES ONE SECONDARY WITH TAP TWO SECONDARIES WITH TAP X3 X3 Type: Quick Connector Material: Brass Y1 Y2 Y1 Y2 Y3 Approximate dimensions in inches (mm. * Brown color available upon request 136

138 URU kv VOLTAGE TRANSFORMER Electrical characteristics Code * (CEP Ratio : /600: /600 &350/600:1 (V 40250/ 69000GY 40250/ 69000GY 40250/ 69000GY (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding W,X,M,Y,ZZ / W,X,M,Y,Z /67.08 & 115/ W,X,M,Y,Z & 0.3 W,X,M,Y,Z & * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request. Notes: 137

139 VRU kv VOLTAGE TRANSFORMER ARTECHE UR/VR series are dry type outdoor service voltage transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. OUTDOOR 60 Hertz The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Mechanical characteristics Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* (965.2 The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions ( ( ( ( (500 Drawing number: PRIMARY TERMINAL GROUND TERMINAL CONNEC- TIONS Type: TE-250 Material: Copper Range: 2/0 TRE-250MCM Type: NEMA-2 Material: Copper Type: NEMA-4 Material: Copper Type: TE Material: Copper Range: 4TRE-250MCM SECONDARY TERMINAL ø1/4 MARKING (Single Ratio ONE SECONDARY TWO SECONDARIES ONE SECONDARY WITH TAP TWO SECONDARIES WITH TAP X3 X3 Type: Quick Connector Material: Brass Approximate dimensions in inches (mm. * Brown color available upon request Y1 Y2 Y1 Y2 Y

140 VRU kv VOLTAGE TRANSFORMER Electrical characteristics Code * (CEP Ratio (V (V IEEE Metering Continuous Rated Factor (Un Rated Factor 30 s (Un Burden (VA Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & : /69000Y W,X,M,X,Y,Z,ZZ /600 & 350/600: /1039 & 350/600: & 600: /69000Y or 69000/69000Y 197/115 & 115/ /69000Y 115/66.4 & 197/ /69000Y 115 & 115 * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request. Notes: 0.3 W,X,M,X,Y,Z & 0.3 W,X,M,X,Y,Z 0.3 W,X,M,X,Y,Z & 0.3 W,X,M,X,Y,Z 0.3 W,X,M,X,Y,Z & 0.3 W,X,M,X,Y,Z & & & 2000 Winding

141 CRE-7 5 kv CURRENT TRANSFORMER OUTDOOR 60 Hertz CR Series are dry type outdoor service current transformers. The core is encapsulated with Type B epoxy resin for excellence in internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic resin provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the module. The device is maintenance free, ensuring a long mechanical and electrical life. The core is built with silicon steel lamination. The blade is high permeability grain oriented Type for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed IEEE C requirements. Mechanical characteristics Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray (238 2 x 8.5 (2 x 216 Terminal box 12.4 (315 2 x 6.83 (2 x (2 x ( (267 Two holes to conduit pipe A1 - NPT 11 (279 Drawing number: PRIMARY TERMINAL GROUND CONNECTOR SECONDARY TERMINAL ONE SECONDARY CONNEC- TIONS ø1/4 MARKING (Single Ratio ONE SECONDARY with tap Type: NEMA-2 Material: Copper Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass Xn Approximate dimensions in inches (mm. * Brown color available upon request 140

142 CRE-7 5 kv CURRENT TRANSFORMER Electrical characteristics Code * (CEP Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Highest Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : B1.8 T : B1.8 T : B1.8 T : B1.8 T : B1.8 T : B1.8 T : B1.8 T : B1.8 T : B1.8 T : B1.8 T : B1.8 T : B1.8 T : B1.8 T : B1.8 T : B1.8 T : B1.8 T : B1.8 T * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request. Notes: 141

143 CRB kv CURRENT TRANSFORMER OUTDOOR 60 Hertz ARTECHE CR series are dry type outdoor service current transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Mechanical characteristics Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* ø10.63 ( ( (219 2 holes to conduit pipe ø1 NPT 1 hole ø9/16 to ground connection Nameplate 10 (254 Drawing number: PRIMARY TERMINAL GROUND CONNECTOR SECONDARY TERMINAL ONE SECONDARY CONNEC- TIONS ø1/4 MARKING (Single Ratio Type: NEMA-2 Material: Copper Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass Approximate dimensions in inches (mm. * Brown color available upon request 142

144 CRB kv CURRENT TRANSFORMER Electrical characteristics Code * (CEP Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : B : B : B : B : B : B : B : B : B : B : B : B : B : B : B : B : B : B Shorting Link : B : B : B : B : B : B : B : B : B : B : B : B : B : B : B : B : B : B * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request

145 CRB kv CURRENT TRANSFORMER Electrical characteristics Code * (CEP Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding High Extended Range 5% nominal current to Rating Factor : S B : S B : S B : S B : S B : S B : S B : S B : S B : S B : S B : S B : S B : S B : S B : S B : S B : S B High Extended Range 1% nominal current to Rating Factor : B : B : B : B * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request

146 CRB kv CURRENT TRANSFORMER Notes: 145

147 CRE kv CURRENT TRANSFORMER OUTDOOR 60 Hertz ARTECHE CR series are dry type outdoor service current transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Mechanical characteristics Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* ø12.05 ( ( (219 2 holes to conduit pipe ø1 NPT 1 hole ø9/16 to ground connection Nameplate 10 (254 Drawing number: PRIMARY TERMINAL GROUND CONNECTOR SECONDARY TERMINAL ONE SECONDARY CONNEC- TIONS ø1/4 MARKING (Single Ratio ONE SECONDARY with tap Type: NEMA-2 Material: Copper Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass Xn Approximate dimensions in inches (mm. * Brown color available upon request 146

148 CRE kv CURRENT TRANSFORMER Electrical characteristics Code * (CEP Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T /20:5 2.0/ B-0.5/0.3B-1.8 T75/T /50:5 2.0/ B-0.5/0.3B-1.8 T75/T /60:5 2.0/ B-0.5/0.3B-1.8 T75/T /100:5 2.0/ B-0.5/0.3B-1.8 T75/T /150:5 2.0/ B-0.5/0.3B-1.8 T75/T /200:5 2.0/ B-0.5/0.3B-1.8 T75/T :300:5 2.0/ B-0.5/0.3B-1.8 T75/T /400:5 2.0/ B-0.5/0.3B-1.8 T75/T /600:5 2.0/ B-0.5/0.3B-1.8 T75/T /800:5 1.2/ B-0.5/0.3B-1.8 T75/T /1000:5 1.0/ B-0.5/0.3B-1.8 T75/T /1200:5 1.0/ B-0.5/0.3B-1.8 T75/T : B : B : B : B : B : B : B : B : B /10:5 2.0/ B-0.5/0.15B /20:5 2.0/ B-0.5/0.15B /600:5 2.0/ B-0.5/0.15B /800:5 1.2/ B-0.5/0.15B /1000:5 1.0/ B-0.5/0.15B /1200:5 1.0/ B-0.5/0.15B

149 CRE kv CURRENT TRANSFORMER Electrical characteristics Code * (CEP Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding Shorting Link : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T High Extended Range 5% nominal current to Rating Factor : S B : S B : S B : S B : S B : S B : S B : S B : S B : S B : S B High Extended Range 1% nominal current to Rating Factor : B : B : B : B * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request

150 CRE kv CURRENT TRANSFORMER Notes: 149

151 CRF kv CURRENT TRANSFORMER OUTDOOR 60 Hertz ARTECHE CR series are dry type outdoor service current transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Mechanical characteristics Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* ø13,70 ( (219 Lifting holes ø3/4 ( (437 2 Holes to conduit pipe ø1 NPT 1 hole ø9/16 to ground connection 10 (254 Nameplate Drawing number: / ** PRIMARY TERMINAL GROUND CONNECTOR SECONDARY TERMINAL ONE SECONDARY CONNEC- TIONS ø1/4 MARKING (Single Ratio ONE SECONDARY with tap Type: NEMA-2 Type: NEMA-4 Material: Copper Material: Copper ** Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass Xn Approximate dimensions in inches (mm. * Brown color available upon request 150

152 CRF kv CURRENT TRANSFORMER Electrical characteristics Code * (CEP Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T /10:5 2.0/ B-0.9/0.3B-1.8 T100/ /20:5 2.0/ B-0.9/0.3B-1.8 T100/ /50:5 2.0/ B-0.9/0.3B-1.8 T100/ /60:5 2.0/ B-0.9/0.3B-1.8 T100/ /100:5 2.0/ B-0.9/0.3B-1.8 T100/ /150:5 2.0/ B-0.9/0.3B-1.8 T100/ /200:5 2.0/ B-0.9/0.3B-1.8 T100/ /300:5 2.0/ B-0.9/0.3B-1.8 T100/ /400:5 2.0/ B-0.9/0.3B-1.8 T100/ /600:5 2.0/ B-0.9/0.3B-1.8 T100/ /800:5 1.2/ B-0.9/0.3B-1.8 T100/ /1000:5 1.0/ B-0.9/0.3B-1.8 T100/ /1200:5 1.0/ B-0.9/0.3B-1.8 T100/ : B : B : B : B : B : B : B : B : B /10:5 2.0/ B-0.5/0.15B /20:5 2.0/ B-0.5/0.15B /600:5 2.0/ B-0.5/0.15B /800:5 1.2/ B-0.5/0.15B /1000:5 1.0/ B-0.5/0.15B /1200:5 1.0/ B-0.5/0.15B

153 CRF kv CURRENT TRANSFORMER Electrical characteristics Code * (CEP Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding High Extended Range 5% nominal current to Rating Factor : S B : S B : S B : S B : S B : S B : S B : S B : S B High Extended Range 1% nominal current to Rating Factor : B : B : B : B * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request

154 CRF kv CURRENT TRANSFORMER Notes: 153

155 CRE kv CURRENT TRANSFORMER OUTDOOR 60 Hertz ARTECHE CR series are dry type outdoor service current transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. Mechanical characteristics ø12.05 (306 The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* ( (219 2 holes to conduit pipe ø1 NPT 1 hole ø9/16 to ground connection 10 (254 Nameplate Drawing number: PRIMARY TERMINAL GROUND CONNECTOR SECONDARY TERMINAL ONE SECONDARY CONNEC- TIONS ø1/4 MARKING (Single Ratio Type: NEMA-2 Material: Copper Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass Approximate dimensions in inches (mm. * Brown color available upon request 154

156 CRE kv CURRENT TRANSFORMER Electrical characteristics Code * (CEP Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : B-0.9 T : B-0.9 T : B-0.9 T : B-0.9 T : B-0.9 T : B-0.9 T : B-0.9 T : B-0.9 T : B-0.9 T : B-0.9 T : B-0.9 T : B-0.9 T : B-0.9 T : B-0.9 T : B-0.9 T : B-0.9 T : B-0.9 T : B-0.9 T High Extended Range 1% nominal current to Rating Factor : B : B : B : B * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request. Notes: 155

157 CRF kv CURRENT TRANSFORMER OUTDOOR 60 Hertz ARTECHE CR series are dry type outdoor service current transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Mechanical characteristics Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* ø13,70 ( (219 Lifting holes ø3/4 ( (437 2 Holes to conduit pipe ø1 NPT 1 hole ø9/16 to ground connection 10 (254 Nameplate Drawing number: / ** PRIMARY TERMINAL GROUND CONNECTOR SECONDARY TERMINAL ONE SECONDARY CONNEC- TIONS ø1/4 MARKING (Single Ratio ONE SECONDARY with tap Type: NEMA-2 Type: NEMA-4 Material: Copper Material: Copper ** Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass Xn Approximate dimensions in inches (mm. * Brown color available upon request 156

158 CRF kv CURRENT TRANSFORMER Electrical characteristics Code * (CEP Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T /10:5 2.0/ B-0.9/0.3B-1.8 T100/ /20:5 2.0/ B-0.9/0.3B-1.8 T100/ /50:5 2.0/ B-0.9/0.3B-1.8 T100/ /60:5 2.0/ B-0.9/0.3B-1.8 T100/ /100:5 2.0/ B-0.9/0.3B-1.8 T100/ /150:5 2.0/ B-0.9/0.3B-1.8 T100/ /200:5 2.0/ B-0.9/0.3B-1.8 T100/ /300:5 2.0/ B-0.9/0.3B-1.8 T100/ /400:5 2.0/ B-0.9/0.3B-1.8 T100/ /600:5 2.0/ B-0.9/0.3B-1.8 T100/ /800:5 1.2/ B-0.9/0.3B-1.8 T100/ /1000:5 1.0/ B-0.9/0.3B-1.8 T100/ /1200:5 1.0/ B-0.9/0.3B-1.8 T100/ : B : B : B : B : B : B : B : B : B /10:5 2.0/ B-0.5/B /20:5 2.0/ B-0.5/B /600:5 2.0/ B-0.5/B /800:5 1.2/ B-0.5/B /1000:5 1.0/ B-0.5/B /1200:5 1.0/ B-0.5/B

159 CRF kv CURRENT TRANSFORMER Electrical characteristics Code * (CEP Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding High Extended Range 5% nominal current to Rating Factor : S B : S B : S B : S B : S B : S B : S B : S B : S B High Extended Range 1% nominal current to Rating Factor : B : B : B : B * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request

160 CRF kv CURRENT TRANSFORMER Notes: 159

161 C CE kv CURRENT TRANSFORMER OUTDOOR 60 Hertz ARTECHE CE series are dry type outdoor service top-core current transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. The cores and windings are located in the upper part of the transformer. This head is coated with a conductive layer, which provides an adequate electric field control. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Mechanical characteristics Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* ø16.14 ( ( ( (350 Terminal box Ground connector (350 Drawing number: PRIMARY TERMINAL GROUND CONNECTOR SECONDARY TERMINAL ONE SECONDARY CONNEC- TIONS MARKING (Single Ratio ONE SECONDARY with tap Type: PM30MC0-1-4N-E Material: Aluminum Type: LZ-500 Material: Copper Range: 4/OTRE-500MCM Type: Hex screw Material: Steel Xn Approximate dimensions in inches (mm. * Brown color available upon request 160

162 CE kv CURRENT TRANSFORMER Electrical characteristics Code * (CEP Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding :5 2, B-1.8 T :5 2, B-1.8 T :5 2, B-1.8 T :5 2, B-1.8 T :5 2, B-1.8 T :5 2, B-1.8 T :5 2, B-1.8 T :5 2, B-1.8 T :5 2, B-1.8 T :5 2, B-1.8 T :5 2, B-1.8 T :5 2, B-1.8 T :5 2, B-1.8 T :5 2, B-1.8 T :5 2, B-1.8 T :5 2, B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T /20:5 3.0/ B-1.8/0.3B1.8 T200/T /50:5 3.0/ B-1.8/0.3B1.8 T200/T /60:5 3.0/ B-1.8/0.3B1.8 T200/T /100:5 3.0/ B-1.8/0.3B1.8 T200/T /150:5 3.0/ B-1.8/0.3B1.8 T200/T /200:5 3.0/ B-1.8/0.3B1.8 T200/T /300:5 3.0/ B-1.8/0.3B1.8 T200/T /400:5 3.0/ B-1.8/0.3B1.8 T200/T /600:5 3.0/ B-1.8/0.3B1.8 T200/T /800:5 3.0/ B-1.8/0.3B1.8 T200/T /1000:5 3.0/ B-1.8/0.3B1.8 T200/T /1200:5 3.0/ B-1.8/0.3B1.8 T200/T /1500:5 3.0/ B-1.8/0.3B1.8 T200/T /2000:5 2.4/ B-1.8/0.3B1.8 T400/T /3000:5 2.4/ B-1.8/0.3B1.8 T400/T * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request

163 CRF kv CURRENT TRANSFORMER OUTDOOR 60 Hertz ARTECHE CR series are dry type outdoor service current transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Mechanical characteristics Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* ø13.7 ( ( (219 2 hole to conduit pipe ø1 NPT 1 hole ø9/16 to ground connection 10 (254 Nameplate Drawing number: PRIMARY TERMINAL GROUND CONNECTOR SECONDARY TERMINAL ONE SECONDARY CONNEC- TIONS ø1/4 MARKING (Single Ratio ONE SECONDARY with tap Type: NEMA-2 Material: Copper Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass Xn Approximate dimensions in inches (mm. * Brown color available upon request 162

164 CRF kv CURRENT TRANSFORMER Electrical characteristics Code * (CEP Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T /20:5 2.0/ B-0.9/0.3B-1.8 T100/T /50:5 2.0/ B-0.9/0.3B-1.8 T100/T /60:5 2.0/ B-0.9/0.3B-1.8 T100/T /100:5 2.0/ B-0.9/0.3B-1.8 T100/T /150:5 2.0/ B-0.9/0.3B-1.8 T100/T /200:5 2.0/ B-0.9/0.3B-1.8 T100/T

165 CRF kv CURRENT TRANSFORMER Electrical characteristics Code * (CEP Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding /300:5 2.0/ B-0.9/0.3B-1.8 T100/T /400:5 2.0/ B-0.9/0.3B-1.8 T100/T /600:5 2.0/ B-0.9/0.3B-1.8 T100/T /800:5 1.2/ B-0.9/0.3B-1.8 T100/T /1000:5 1.0/ B-0.9/0.3B-1.8 T100/T /1200:5 1.0/ B-0.9/0.3B-1.8 T100/T : B : B : B : B : B : B : B : B /10:5 2.0/ B-0.5/B /20:5 2.0/ B-0.5/B /600:5 2.0/ B-0.5/B /800:5 1.2/ B-0.5/B /1000:5 1.0/ B-0.5/B /1200:5 1.0/ B-0.5/B High Extended Range 1% nominal current to Rating Factor : B : B : B : B * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request

166 CRF kv CURRENT TRANSFORMER Notes: 165

167 CRH kv CURRENT TRANSFORMER OUTDOOR 60 Hertz ARTECHE CR series are dry type outdoor service current transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Mechanical characteristics Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* ( Nameplate (626.8 terminals Lifting holes 1 hole ø9/16 to ground connector 2 holes ø1 to conduit pipe NPT 9.84 ( (250 Drawing number: PRIMARY TERMINAL GROUND CONNECTOR SECONDARY TERMINAL ONE SECONDARY CONNEC- TIONS 1500 A 2000 A ø1/4 MARKING (Single Ratio ONE SECONDARY with tap Type: NEMA-4 Material: Copper Type: LZ-250 Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass Xn Approximate dimensions in inches (mm. * Brown color available upon request 166

168 CRH kv CURRENT TRANSFORMER Electrical characteristics Code * (CEP Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T /20:5 3.0/ B-1.8/0.3B1.8 T100/T /50:5 3.0/ B-1.8/0.3B1.8 T100/T /60:5 3.0/ B-1.8/0.3B1.8 T100/T /100:5 3.0/ B-1.8/0.3B1.8 T100/T /150:5 3.0/ B-1.8/0.3B1.8 T100/T /200:5 3.0/ B-1.8/0.3B1.8 T100/T /300:5 3.0/ B-1.8/0.3B1.8 T100/T /400:5 3.0/ B-1.8/0.3B1.8 T100/T /600:5 3.0/ B-1.8/0.3B1.8 T100/T /800:5 3.0/ B-1.8/0.3B1.8 T100/T /1000:5 3.0/ B-1.8/0.3B1.8 T100/T /1200:5 3.0/ B-1.8/0.3B1.8 T100/T High Extended Range 1% nominal current to Rating Factor : B : B : B : B * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request

169 CRK kv CURRENT TRANSFORMER OUTDOOR 60 Hertz ARTECHE CR series are dry type outdoor service current transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Mechanical characteristics Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* ( ( terminals 1 Hole ø9/16 to ground connection ( (350 Nameplate (350 Drawing number: PRIMARY TERMINAL GROUND CONNECTOR SECONDARY TERMINAL ONE SECONDARY CONNEC- TIONS 1500 A 2000 A MARKING (Single Ratio ONE SECONDARY with tap Type: NEMA-4 Material: Copper Type: LZ-250 Material: Copper Range: 4TRE-250MCM Type: Hex screw Material: Steel Xn Approximate dimensions in inches (mm. * Brown color available upon request 168

170 CRK kv CURRENT TRANSFORMER Electrical characteristics Code * (CEP Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T : B-1.8 T /20:5 3.0/ B-1.8/0.3B1.8 T200/T /50:5 3.0/ B-1.8/0.3B1.8 T200/T /60:5 3.0/ B-1.8/0.3B1.8 T200/T /100:5 3.0/ B-1.8/0.3B1.8 T200/T /150:5 3.0/ B-1.8/0.3B1.8 T200/T /200:5 3.0/ B-1.8/0.3B1.8 T200/T /300:5 3.0/ B-1.8/0.3B1.8 T200/T /400:5 3.0/ B-1.8/0.3B1.8 T200/T /600:5 3.0/ B-1.8/0.3B1.8 T200/T /800:5 3.0/ B-1.8/0.3B1.8 T200/T /1000:5 3.0/ B-1.8/0.3B1.8 T200/T /1200:5 3.0/ B-1.8/0.3B1.8 T200/T /1500:5 3.0/ B-1.8/0.3B1.8 T200/T /2000:5 2.4/ B-1.8/0.3B1.8 T200/T * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request

171 CE kv CURRENT TRANSFORMER OUTDOOR 60 Hertz ARTECHE CE series are dry type outdoor service top-core current transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. The cores and windings are located in the upper part of the transformer. This head is coated with a conductive layer, which provides an adequate electric field control. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Mechanical characteristics Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* ø16.14 (410 ø37.87 (962 ø(49/16 ( ( (250 Terminal box Ground connector 9.84 (250 Drawing number: PRIMARY TERMINAL GROUND CONNECTOR SECONDARY TERMINAL ONE SECONDARY CONNEC- TIONS MARKING (Single Ratio ONE SECONDARY with tap Type: PM30MC0-1-4N-E Material: Aluminum Type: LZ-500 Material: Copper Range: 4/OTRE-500MCM Type: Hex screw Material: Steel Xn Approximate dimensions in inches (mm. * Brown color available upon request 170

172 CE kv CURRENT TRANSFORMER Electrical characteristics Code * (CEP Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding /50:5 3.0/ B-1.8/0.3B1.8 T200/T /60:5 3.0/ B-1.8/0.3B1.8 T200/T /100:5 3.0/ B-1.8/0.3B1.8 T200/T /150:5 3.0/ B-1.8/0.3B1.8 T200/T /200:5 3.0/ B-1.8/0.3B1.8 T200/T /300:5 3.0/ B-1.8/0.3B1.8 T200/T /400:5 3.0/ B-1.8/0.3B1.8 T200/T /600:5 3.0/ B-1.8/0.3B1.8 T200/T /800:5 3.0/ B-1.8/0.3B1.8 T200/T /1000:5 3.0/ B-1.8/0.3B1.8 T200/T /1200:5 3.0/ B-1.8/0.3B1.8 T200/T /1500:5 3.0/ B-1.8/0.3B1.8 T200/T /2000:5 2.4/ B-1.8/0.3B1.8 T400/T /3000:5 2.4/ B-1.8/0.3B1.8 T400/T High Extended Range 1% nominal current to Rating Factor : B : B : B : B * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request. Notes: 171

173 CRH kv CURRENT TRANSFORMER OUTDOOR 60 Hertz ARTECHE CR series are dry type outdoor service current transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. Mechanical characteristics The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* (385 Nameplate ( Lifting holes Hole ø9/16 to ground connection Terminal secondary box with NPT 1 Quick Connector 9.84 ( (250 Drawing number: PRIMARY TERMINAL GROUND CONNECTOR SECONDARY TERMINAL ONE SECONDARY CONNEC- TIONS MARKING (Single Ratio ONE SECONDARY with tap Type: NEMA-4 Material: Copper Type: LZ-250 Material: Copper Range: 4TRE-250MCM Type: Hex screw Material: Steel Xn Approximate dimensions in inches (mm. * Brown color available upon request 172

174 CRH kv CURRENT TRANSFORMER Electrical characteristics Code * (CEP Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding /50:5 2.4/ B-1.8/0.3B1.8 T100/T /60:5 2.4/ B-1.8/0.3B1.8 T100/T /100:5 2.4/ B-1.8/0.3B1.8 T100/T /150:5 2.4/ B-1.8/0.3B1.8 T100/T /200:5 2.4/ B-1.8/0.3B1.8 T100/T /300:5 2.4/ B-1.8/0.3B1.8 T100/T /400:5 2.4/ B-1.8/0.3B1.8 T100/T /600:5 2.4/ B-1.8/0.3B1.8 T100/T /800:5 2.4/ B-1.8/0.3B1.8 T100/T /1000:5 2.4/ B-1.8/0.3B1.8 T100/T /1200:5 2.4/ B-1.8/0.3B1.8 T100/T High Extended Range 1% nominal current to Rating Factor : B : B : B : B * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request. Notes: 173

175 CRK kv CURRENT TRANSFORMER OUTDOOR 60 Hertz ARTECHE CR series are dry type outdoor service current transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. Mechanical characteristics The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* ( ( terminals Lifting holes 1 Hole ø9/16 to ground connector Nameplate ( Holes ø1 to conduit pipe NPT ( (350 Drawing number: PRIMARY TERMINAL GROUND CONNECTOR SECONDARY TERMINAL ONE SECONDARY CONNEC- TIONS 1500 A 2000 A MARKING (Single Ratio ONE SECONDARY with tap Type: NEMA-4 Material: Copper Type: LZ-250 Material: Copper Range: 4TRE-250MCM Type: Hex screw Material: Steel Xn Approximate dimensions in inches (mm. * Brown color available upon request 174

176 CRK kv CURRENT TRANSFORMER Electrical characteristics Code * (CEP Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding /50:5 3.0/ B-1.8/0.3B1.8 T200/T /60:5 3.0/ B-1.8/0.3B1.8 T200/T /100:5 3.0/ B-1.8/0.3B1.8 T200/T /150:5 3.0/ B-1.8/0.3B1.8 T200/T /200:5 3.0/ B-1.8/0.3B1.8 T200/T /300:5 3.0/ B-1.8/0.3B1.8 T200/T /400:5 3.0/ B-1.8/0.3B1.8 T200/T /600:5 3.0/ B-1.8/0.3B1.8 T200/T /800:5 3.0/ B-1.8/0.3B1.8 T200/T /1000:5 3.0/ B-1.8/0.3B1.8 T200/T /1200:5 3.0/ B-1.8/0.3B1.8 T200/T /1500:5 3.0/ B-1.8/0.3B1.8 T200/T /2000:5 2.4/ B-1.8/0.3B1.8 T200/T * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request. Notes: 175

177 C CE kv CURRENT TRANSFORMER OUTDOOR 60 Hertz ARTECHE CE series are dry type outdoor service top-core current transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. The cores and windings are located in the upper part of the transformer. This head is coated with a conductive layer, which provides an adequate electric field control. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Mechanical characteristics Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* ø16.14 (410 ø35.5 ( ( (350 Terminal box Ground connector (350 Drawing number: PRIMARY TERMINAL GROUND CONNECTOR SECONDARY TERMINAL ONE SECONDARY CONNEC- TIONS MARKING (Single Ratio ONE SECONDARY with tap Type: PM30MC0-1-4N-E Material: Aluminum Type: LZ-500 Material: Copper Range: 4/OTRE-500MCM Type: Hex screw Material: Steel Xn Approximate dimensions in inches (mm. * Brown color available upon request 176

178 CE kv CURRENT TRANSFORMER Electrical characteristics Code * (CEP Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding /50:5 2.4/ B-1.8/0.3B1.8 T200/T /60:5 2.4/ B-1.8/0.3B1.8 T200/T /100:5 2.4/ B-1.8/0.3B1.8 T200/T /150:5 2.4/ B-1.8/0.3B1.8 T200/T /200:5 2.4/ B-1.8/0.3B1.8 T200/T /300:5 2.4/ B-1.8/0.3B1.8 T200/T /400:5 2.4/ B-1.8/0.3B1.8 T200/T /600:5 2.4/ B-1.8/0.3B1.8 T200/T /800:5 2.4/ B-1.8/0.3B1.8 T200/T /1000:5 2.4/ B-1.8/0.3B1.8 T200/T /1200:5 2.4/ B-1.8/0.3B1.8 T200/T /1500:5 2.4/ B-1.8/0.3B1.8 T200/T /2000:5 2.4/ B-1.8/0.3B1.8 T400/T /3000:5 2.4/ B-1.8/0.3B1.8 T400/T High Extended Range 1% nominal current to Rating Factor : B : B : B : B * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request. Notes: 177

179 CRH kv CURRENT TRANSFORMER OUTDOOR 60 Hertz ARTECHE CR series are dry type outdoor service current transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. Mechanical characteristics The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* ( (385 Hole ø9/16 to ground connection Lifting holes ø3/4 Terminal secondary box with ø1 NPT 30.7 ( ( (250 Drawing number: PRIMARY TERMINAL GROUND CONNECTOR SECONDARY TERMINAL ONE SECONDARY CONNEC- TIONS MARKING (Single Ratio ONE SECONDARY with tap Type: NEMA-4 Material: Copper Type: LZ-250 Material: Copper Range: 4TRE-250MCM Type: Hex screw Material: Steel Xn Approximate dimensions in inches (mm. * Brown color available upon request 178

180 CRH kv CURRENT TRANSFORMER Electrical characteristics Code * (CEP Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding /50:5 2.4/ B-1.8/0.3B1.8 T100/T /60:5 2.4/ B-1.8/0.3B1.8 T100/T /100:5 2.4/ B-1.8/0.3B1.8 T100/T /150:5 2.4/ B-1.8/0.3B1.8 T100/T /200:5 2.4/ B-1.8/0.3B1.8 T100/T /300:5 2.4/ B-1.8/0.3B1.8 T100/T /400:5 2.4/ B-1.8/0.3B1.8 T100/T /600:5 2.4/ B-1.8/0.3B1.8 T100/T /800:5 2.4/ B-1.8/0.3B1.8 T100/T /1000:5 2.4/ B-1.8/0.3B1.8 T100/T /1200:5 2.4/ B-1.8/0.3B1.8 T100/T High Extended Range 1% nominal current to Rating Factor : B : B : B : B * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request. Notes: 179

181 CRK kv CURRENT TRANSFORMER OUTDOOR 60 Hertz ARTECHE CR series are dry type outdoor service current transformers. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. Mechanical characteristics The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* (527.5 M ( terminal box Lifting holes 1 Hole ø9/16 to ground connector Nameplate ( Holes ø1 to conduit pipe NPT ( (350 Drawing number: PRIMARY TERMINAL GROUND CONNECTOR SECONDARY TERMINAL ONE SECONDARY CONNEC- TIONS 1500 A 2000 A MARKING (Single Ratio ONE SECONDARY with tap Type: NEMA-4 Material: Copper Type: LZ-250 Material: Copper Range: 4TRE-250MCM Type: Hex screw Material: Steel Xn Approximate dimensions in inches (mm. * Brown color available upon request 180

182 CRK kv CURRENT TRANSFORMER Electrical characteristics Code * (CEP Ratio (: (A Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering Relay Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding /50:5 2.4/ B-1.8/0.3B1.8 T200/T /60:5 2.4/ B-1.8/0.3B1.8 T200/T /100:5 2.4/ B-1.8/0.3B1.8 T200/T /150:5 2.4/ B-1.8/0.3B1.8 T200/T /200:5 2.4/ B-1.8/0.3B1.8 T200/T /300:5 2.4/ B-1.8/0.3B1.8 T200/T /400:5 2.4/ B-1.8/0.3B1.8 T200/T /600:5 2.4/ B-1.8/0.3B1.8 T200/T /800:5 2.4/ B-1.8/0.3B1.8 T200/T /1000:5 2.4/ B-1.8/0.3B1.8 T200/T /1200:5 2.4/ B-1.8/0.3B1.8 T200/T /1500:5 2.4/ B-1.8/0.3B1.8 T400/T /2000:5 2.4/ B-1.8/0.3B1.8 T400/T * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request. Notes: 181

183 KM kv COMBINED TRANSFORMER OUTDOOR 60 Hertz ARTECHE KM series are dry type outdoor service combination CT-PT. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Mechanical characteristics Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* ø14 (356 Nameplate 22 ( (330 2 holes to conduit pipe ø1 1 hole ø9/16 to ground connection 10 (254 Drawing number: PRIMARY TERMINAL GROUND CONNECTOR SECONDARY TERMINAL ONE SECONDARY ø1/4 C1 H0 C2 CONNEC- TIONS Type: NEMA-2 Material: Copper Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass MARKING (Single Ratio V1 V2 ONE SECONDARY with tap C1 C2 H0 C3 V1 V2 Approximate dimensions in inches (mm. *Brown color available upon request 182

184 KM kv COMBINED TRANSFORMER Electrical characteristics Code * (CEP Ratio (: Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering [ Transformer] IEEE Metering [ Transformer] Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : , B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z /20:5 2.0/ B0.2/B W,X,M,Y/0.6Z /50:5 2.0/ B0.2/B W,X,M,Y/0.6Z /200:5 2.0/ B0.2/B W,X,M,Y/0.6Z /600:5 2.0/ B0.2/B W,X,M,Y/0.6Z /800:5 2.0/ B0.2/B W,X,M,Y/0.6Z /800:5 3.0/ B0.2/B W,X,M,Y/0.6Z /1000:5 2.0/ B0.2/B W,X,M,Y/0.6Z /1200:5 2.0/ B0.2/B W,X,M,Y/0.6 Z High Extended Range 1% nominal current to Rating Factor : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request. Ratings VT Ratio (V (V Burden (VA Continuous Rated Factor (Un Rated Factor 30s (Un 60:1 7200/12470GY Notes: Additional VT ratios are available. Please contact Arteche for details

185 MK kv METERING UNIT ARTECHE ME/MK series metering units are outdoor, three-phase, polemounted metering racks. The rack is made of lightweight aluminium designed to mount on poles in an upright position. It includes two galvanized steel mounting bolts for attaching the metering unit to the pole, with pole diameters available from 8 to 14. Optional galvanized steel structures and/or other pole diameters are available upon request. MK series incorporate 3 combined transformers mounted vertically. Their core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. OUTDOOR 60 Hertz The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Mechanical characteristics Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* ( ( ( (1349 Drawing number: PRIMARY TERMINAL GROUND CONNECTOR CONNECTION PLATE L3 L2 L1 CONNEC- TIONS Type: NEMA-2 Material: Copper Type: TE Material: Copper Range: 4TRE-250MCM SECONDARY TERMINAL MARKING VT1 VT2 VT3 CT1 CT2 CT3 ø1/ Type: Quick Connector Material: Brass Approximate dimensions in inches (mm. *Brown color available upon request 184

186 MK kv METERING UNIT Electrical characteristics Code * (CEP Ratio (: Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering [ Transformer] IEEE Metering [ Transformer] Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : , B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z High Extended Range 1% nominal current to Rating Factor : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z * For HCEP Option add ( H to the end of the code number. Additional ratings available upon request. Ratings VT Ratio (V (V Burden (VA Continuous Rated Factor (Un Rated Factor 30s (Un 60:1 7200/12470GY Notes: Additional VT ratios are available. Please contact Arteche for details

187 ME kv METERING UNIT ARTECHE ME/MK series metering units are outdoor. three-phase. polemounted metering racks. The rack is made of lightweight aluminium designed to mount on poles in an upright position. It includes two galvanized steel mounting bolts for attaching the metering unit to the pole. with pole diameters available from 8 to 14. Optional galvanized steel structures and/or other pole diameters are available upon request. ME series incorporate 3 current transformers mounted vertically and 3 voltage transformers mounted horizontally. Their core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. OUTDOOR 60 Hertz The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage. achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Y Z X W Drawing number: PRIMARY TERMINAL CT PRIMARY TERMINAL VT GROUND CONNECTOR SECONDARY TERMINAL ø1/4 CONNEC- TIONS Type: NEMA-2 Material: Copper Type: TE-4T Material: Copper Range: 8SOL-4TRE Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass 186

188 ME kv METERING UNIT Characteristics Type Transformers Code * (CEP Dimensions (in Potential With FUSE in the secondary box Without FUSE in the secondary box W X Y Z Weigth with Aluminium rack (lb ME-015 CRB-17 URL ME-015 CRB-17 VRL ME-015 CRB-17 URJ ME-015 CRB-17 VRJ ME-015 CRE-17 URL ME-015 CRE-17 VRL ME-015 CRE-17 URJ ME-015 CRE-17 VRJ * For HCEP Option add ( H to the end of the code number. Approximate dimensions in inches. For detail electric characteristics see particular instrument transformer detail in its data sheet within this publication. Notes: 187

189 MI kv METERING UNIT ARTECHE MI series metering units are outdoor, three-phase, pad-mounted cabinets. The cabinet is made of #12 caliber stainless steel lamination (2.7 mm or in with Munsell Green #7GY 3.29/1.5 powder finish. The doors are pad- lockable with a three point latch and a penta-head bolt. MI series incorporate 3 combined transformers. Their core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. The entire surface of the transformer is coated with a conductive layer that is intended to be solidly grounded when energized. This allows for compact mounting inside switchgear or enclosures. OUTDOOR 60 Hertz The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Mechanical characteristics Material Colors Weight (lbs. Stainless steel Munsell Green 992 The primary bushing well connections are IEEE 386 compliant, rated 200 A loadbreak or 600 A non load-break.. The secondary terminals are pre-wired to a 10 position test switch and 9S meter socket in standard red/black colors. 8 x x 1.22 Air spring 13º (4 Lifting plates W/5/8-11 Bolts Drawing number: MARKING L3 L2 L1 VT1 VT2 VT3 CT1 CT2 CT Approximate dimensions in inches (mm

190 MI kv METERING UNIT Electrical characteristics Code Ratio (: Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering [ Transformer] IEEE Metering [ Transformer] Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z High Extended Range 1% nominal current to Rating Factor : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z Additional ratings available upon request. Ratings VT Ratio (V (V Burden (VA Continuous Rated Factor (Un Rated Factor 30s (Un 60:1 7200/12470GY Notes: Additional VT ratios are available. Please contact Arteche for details

191 KM kv COMBINED TRANSFORMER OUTDOOR 60 Hertz ARTECHE KM series are dry type outdoor service combination CT-PT. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed IEEE C requirements Mechanical characteristics Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* (356 Nameplate 24.5 (622 Lifting Holes 2 holes to conduit pipe ø1 1 hole ø9/16 to ground connection 13 ( (254 Drawing number: PRIMARY TERMINAL GROUND CONNECTOR SECONDARY TERMINAL ONE SECONDARY ø1/4 C1 H0 C2 CONNEC- TIONS Type: NEMA-2 Material: Copper Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass MARKING (Single Ratio V1 V2 ONE SECONDARY with tap C1 C2 H0 C3 V1 V2 Approximate dimensions in inches (mm. *Brown color available upon request 190

192 KM kv COMBINED TRANSFORMER Electrical characteristics Code * (CEP Ratio (: Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering [ Transformer] IEEE Metering [ Transformer] Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z /20:5 2.0/ B0.2/B W,X,M,Y/0.6Z /50:5 2.0/ B0.2/B W,X,M,Y/0.6Z /200:5 2.0/ B0.2/B W,X,M,Y/0.6Z /300:5 2.0/ B0.2/B W,X,M,Y/0.6Z /300:5 4.0/ B0.2/B W,X,M,Y/0.6Z /600:5 2.0/ B0.2/B W,X,M,Y/0.6Z /1000:5 2.0/ B0.2/B W,X,M,Y/0.6Z /1200:5 2.0/ B0.2/B W,X,M,Y/0.6Z High Extended Range 1% nominal current to Rating Factor : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z * For HCEP Option add ( H to the end of the code number. Approximate dimensions in inches. Ratings VT Ratio (V (V Burden (VA Continuous Rated Factor (Un Rated Factor 30s (Un 120: /24940GY Additional VT ratios are available. Please contact Arteche for details. Notes: 191

193 MK kv METERING UNIT ARTECHE ME/MK series metering units are outdoor, three-phase, polemounted metering racks. The rack is made of lightweight aluminium designed to mount on poles in an upright position. It includes two galvanized steel mounting bolts for attaching the metering unit to the pole, with pole diameters available from 8 to 14. Optional galvanized steel structures and/or other pole diameters are available upon request. MK series incorporate 3 combined transformers mounted vertically. Their core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. OUTDOOR 60 Hertz The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Mechanical characteristics Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* ( ( ( (1349 Drawing number: PRIMARY TERMINAL GROUND CONNECTOR CONNECTION PLATE L3 L2 L1 CONNEC- TIONS Type: NEMA-2 Material: Copper Type: TE Material: Copper Range: 4TRE-250MCM SECONDARY TERMINAL MARKING VT1 VT2 VT3 CT1 CT2 CT3 ø1/ Approximate dimensions in inches (mm. *Brown color available upon request Type: Quick Connector Material: Brass 192

194 MK kv METERING UNIT Electrical characteristics Code * (CEP Ratio (: Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering [ Transformer] IEEE Metering [ Transformer] Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z High Extended Range 1% nominal current to Rating Factor : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z * For HCEP Option add ( H to the end of the code number. Approximate dimensions in inches. Ratings VT Ratio (V (V Burden (VA Continuous Rated Factor (Un Rated Factor 30s (Un 120: /24940GY Notes: Additional VT ratios are available. Please contact Arteche for details

195 ME kv METERING UNIT ARTECHE ME/MK series metering units are outdoor. three-phase. polemounted metering racks. The rack is made of lightweight aluminium designed to mount on poles in an upright position. It includes two galvanized steel mounting bolts for attaching the metering unit to the pole. with pole diameters available from 8 to 14. Optional galvanized steel structures and/or other pole diameters are available upon request. ME series incorporate 3 current transformers mounted vertically and 3 voltage transformers mounted horizontally. Their core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. OUTDOOR 60 Hertz The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage. achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Y Z X W Drawing number: PRIMARY TERMINAL CT PRIMARY TERMINAL VT GROUND CONNECTOR SECONDARY TERMINAL ø1/4 CONNEC- TIONS Type: NEMA-2 Material: Copper Type: TE-4T Material: Copper Range: 8SOL-4TRE Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass 194

196 ME kv METERING UNIT Characteristics Type Transformers Code * (CEP Dimensions (in Potential With FUSE in the secondary box Without FUSE in the secondary box W X Y Z Weigth with Aluminium rack (lb ME-025 CRE-24 URJ ME-025 CRE-24 VRJ ME-025 CRF-24 URN ME-025 CRF-24 VRN * For HCEP Option add ( H to the end of the code number. Approximate dimensions in inches. For detail electric characteristics see particular instrument transformer detail in its data sheet within this publication. Notes: 195

197 MI kv METERING UNIT ARTECHE MI series metering units are outdoor, three-phase, pad-mounted cabinets. The cabinet is made of #12 caliber stainless steel lamination (2.7 mm or in with Munsell Green #7GY 3.29/1.5 powder finish. The doors are pad- lockable with a three point latch and a penta-head bolt. MI series incorporate 3 combined transformers. Their core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength, ensuring a long mechanical and electrical life. The transformer is maintenance free. The entire surface of the transformer is coated with a conductive layer that is intended to be solidly grounded when energized. This allows for compact mounting inside switchgear or enclosures. OUTDOOR 60 Hertz The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. The primary bushing well connections are IEEE 386 compliant, rated 200 A loadbreak or 600 A non load-break. The secondary terminals are pre- wired to a 10 position test switch and 9S meter socket in standard red/black colors. Mechanical characteristics Material Colors Weight (lbs. Stainless steel Munsell Green x x 1.22 Air spring 13º (4 Lifting plates W/5/8-11 Bolts Drawing number: MARKING L3 L2 L1 VT1 VT2 VT3 CT1 CT2 CT Approximate dimensions in inches (mm

198 MI kv METERING UNIT Electrical characteristics Code Ratio (: Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering [ Transformer] IEEE Metering [ Transformer] Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z High Extended Range 1% nominal current to Rating Factor : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z Additional ratings available upon request. Ratings VT Ratio (V (V Burden (VA Continuous Rated Factor (Un Rated Factor 30s (Un 120: /24940GY Notes: Additional VT ratios are available. Please contact Arteche for details

199 KM kv COMBINED TRANSFORMER OUTDOOR 60 Hertz ARTECHE KM series are dry type outdoor service combination CT-PT. The core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed IEEE C requirements Mechanical characteristics Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* (350 Nameplate 28.7 (729 Lifting holes ø3/4 2 holes to conduit pipe ø1 1 hole ø9/16 to ground connection 13 ( (254 Drawing number: PRIMARY TERMINAL GROUND CONNECTOR SECONDARY TERMINAL ONE SECONDARY ø1/4 C1 H0 C2 CONNEC- TIONS Type: NEMA-2 Material: Copper Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass MARKING (Single Ratio V1 V2 ONE SECONDARY with tap C1 C2 H0 C3 V1 V2 Approximate dimensions in inches (mm. *Brown color available upon request 198

200 KM kv COMBINED TRANSFORMER Electrical characteristics Code * (CEP Ratio (: Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering [ Transformer] IEEE Metering [ Transformer] Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z /20:5 2.0/ ,4 0.3B-0.5/B W,X,M,Y/1.2Z /50:5 2.0/ ,5 0.3B-0.5/B W,X,M,Y/1.2Z /200:5 2.0/ B-0.5/B W,X,M,Y/1.2Z /600:5 2.0/ B-0.5/B W,X,M,Y/1.2Z /800:5 2.0/ B-0.5/B W,X,M,Y/1.2Z /800:5 3.0/ B-0.5/B W,X,M,Y/1.2Z /1000:5 2.0/ B-0.5/B W,X,M,Y/1.2Z /1200:5 2.0/ B-0.5/B W,X,M,Y/1.2Z High Extended Range 1% nominal current to Rating Factor : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z * For HCEP Option add ( H to the end of the code number. Approximate dimensions in inches. Ratings VT Ratio (V (V Burden (VA Continuous Rated Factor (Un Rated Factor 30s (Un 175: /34500GY Notes: Additional VT ratios are available. Please contact Arteche for details

201 MK kv METERING UNIT ARTECHE ME/MK series metering units are outdoor, three-phase, polemounted metering racks. The rack is made of lightweight aluminium designed to mount on poles in an upright position. It includes two galvanized steel mounting bolts for attaching the metering unit to the pole, with pole diameters available from 8 to 14. Optional galvanized steel structures and/or other pole diameters are available upon request. MK series incorporate 3 combined transformers mounted vertically. Their core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. OUTDOOR 60 Hertz The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage, achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Mechanical characteristics Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Insulation Material Colors Weight (lbs. Creepage distance (in Strike distance (in Resin Gray* ( ( ( (1349 Drawing number: PRIMARY TERMINAL GROUND CONNECTOR CONNECTION PLATE L3 L2 L1 CONNEC- TIONS Type: NEMA-2 Material: Copper Type: TE Material: Copper Range: 4TRE-250MCM SECONDARY TERMINAL MARKING VT1 VT2 VT3 CT1 CT2 CT3 ø1/ Approximate dimensions in inches (mm. *Brown color available upon request Type: Quick Connector Material: Brass 200

202 MK kv METERING UNIT Electrical characteristics Code* (CEP Ratio (: Continuous Rating 30 C Shorttime (ka/1s Shorttime Mechanical (ka peak IEEE Metering [ Transformer] IEEE Metering [ Transformer] Nominal System (kv BIL (kv Power-Frequency Withstand (1 min & Winding : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z : B W,X,M,Y/1.2Z High Extended Range 1% nominal current to Rating Factor : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z : B W,X,M,Y/0.6Z * For HCEP Option add ( H to the end of the code number. Approximate dimensions in inches. Ratings VT Ratio (V (V Burden (VA Continuous Rated Factor (Un Rated Factor 30s (Un 175: /34500GY Notes: Additional VT ratios are available. Please contact Arteche for details

203 ME kv METERING UNIT ARTECHE ME/MK series metering units are outdoor. three-phase. polemounted metering racks. The rack is made of lightweight aluminium designed to mount on poles in an upright position. It includes two galvanized steel mounting bolts for attaching the metering unit to the pole. with pole diameters available from 8 to 14. Optional galvanized steel structures and/or other pole diameters are available upon request. ME series incorporate 3 current transformers mounted vertically and 3 voltage transformers mounted horizontally. Their core is encapsulated with Type B epoxy resin which provides excellent internal dielectric properties and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin (CEP provides resistance to ultraviolet rays and the effects of tracking and erosion on the exterior of the transformer ensuring a long mechanical and electrical life. The transformer is maintenance free. OUTDOOR 60 Hertz The external layer can be manufactured with Hydrophobic Cycloaliphatic Epoxy Resin (HCEP which improves service life expectancy due to its improved tracking and erosion resistance. HCEP additionally increases the transformer s weatherability and offers better performance in heavily polluted environments. The core is built with high permeability grain oriented silicon steel laminations for low losses. The windings are copper wire with copper plate double isolation. The concentric distribution of the coils prevents magnetic flux leakage. achieving greater accuracy and higher capacity to withstand mechanical stresses in adverse operating conditions. Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC requirements. Y Z X W Drawing number: PRIMARY TERMINAL CT PRIMARY TERMINAL VT GROUND CONNECTOR SECONDARY TERMINAL ø1/4 CONNEC- TIONS Type: NEMA-2 Material: Copper Type: TE-4T Material: Copper Range: 8SOL-4TRE Type: TE Material: Copper Range: 4TRE-250MCM Type: Quick Connector Material: Brass 202

204 ME kv METERING UNIT Characteristics Type Transformers Code * (CEP Dimensions (in Potential With FUSE in the secondary box Without FUSE in the secondary box W X Y Z Weigth with Aluminium rack (lb ME-036 CRF-36 URS ME-036 CRF-36 VRS * For HCEP Option add ( H to the end of the code number. Approximate dimensions in inches. For detail electric characteristics see particular instrument transformer detail in its data sheet within this publication. Notes: 203

205

206 ARTECHE Manufacturing Facilities. ARTECHE USA Inc. Arteche USA Pines Blvd. Suite 313. Pembroke Pines, Florida Phone: Fax: Updates: ARTECHE_DS_trfMVGuide_EN Version: D2 ARTECHE