TECHNICAL MANUAL. *PH 15 SEER Multi Position Package Heat Pump Units with R410A

Transcription

1 TEHNIAL MANUAL AL *PH 15 SEE Multi Position Package Heat Pump Units with 10A efer to Service Manual S for installation, operation, and troubleshooting information. All safety information must be followed as provided in the Service Manual. efer to the appropriate Parts atalog for part number information. Models listed on page. This manual is to be used by qualified, professionally trained HVA technicians only. Goodman does not assume any responsibility for property damage or personal injury due to improper service procedures or services performed by an unqualified person. T6010r9 June 01 opyright Goodman Manufacturing ompany, L.P.

2 PODUT IDENTIFIATION The model and manufacturing number are used for positive identification of component parts used in manufacturing. Please use these numbers when requesting service or parts information. G P H 15 6 M 1 A B BAND: G: Goodman Brand A: Amana Brand PODUT TYPE: Package Unit PODUT FAMILY: H: Heat Pump PODUT SEIES: SEE ating ONFIGUATION: M: Mult-position EFIGEANT: : -10A MINO EVISION: A: Initial elease B: Second Minor evision MAJO EVISION: A: Initial elease NOMINAL APAITY: :,000 BTUH 0: 0,000 BTUH 6: 6,000 BTUH :,000 BTUH 9: 8,000 BTUH 60: 60,000 BTUH VOLTAGE: 1: 08-0v/1ph/60Hz. 08-0v/ph/60Hz. 60V/ph/60Hz WANING HIGH VOLTAGE! Disconnect ALL power before servicing or installing this unit. Multiple power sources may be present. Failure to do so may cause property damage, personal injury or death. WANING Goodman will not be responsible for any injury or property damage arising from improper service or service procedures. If you install or perform service on this unit, you assume responsibility for any personal injury or property damage which may result. Many jurisdictions require a license to install or service heating and air conditioning equipment. WANING Installation and repair of this unit should be performed ONLY by individuals meeting (at a minimum) the requirements of an "entry level technician" as specified by the Air-onditioning, Heating, and efrigeration Institute (AHI). Attempting to install or repair this unit without such background may result in product damage, personal injury or death.

3 PODUT IDENTIFIATION The model and manufacturing number are used for positive identification of component parts used in manufacturing. Please use these numbers when requesting service or parts information. *PH15M1AB *PH150M1AB *PH156M1AB *PH15M1AB *PH159M1AB *PH1560M1AB *PH15M1A *PH150M1A *PH156M1A *PH15M1A *PH159M1A *PH1560M1A *PH15M1AD *PH150M1AD *PH156M1AD *PH159M1AD *PH1560M1AD WANING The United States Environmental Protection Agency ( EPA ) has issued various regulations regarding the introduction and disposal of refrigerants introduced into this unit. Failure to follow these regulations may harm the environment and can lead to the imposition of substantial fines. These regulations may vary by jurisdiction. Should questions arise, contact your local EPA office. WANING Do not connect or use any device that is not design certified by Goodman for use with this unit. Serious property damage, personal injury, reduced unit performance and/or hazardous conditions may result from the use of such non-approved devices. WANING To prevent the risk of property damage, personal injury, or death, do not store combustible materials or use gasoline or other flammable liquids or vapors in the vicinity of this appliance.

4 PODUT DESIGN *PH15 models *PH15 (M Series) Package Units are designed for outdoor installations only in either residential or light commercial applications and are available in,.5,,.5, & 5 ton sizes. They are designed for 08/0 volt single phase applications. The connecting ductwork (Supply and eturn) can only be connected for horizontal airflow. A return air filter must be installed behind the return air grille(s) or provision must be made for a filter in an accessible location within the return air duct. The minimum filter area should not be less than those sizes listed in the Specification Section. Under no circumstances should the unit be operated without return air filters. A /" pipe is provided for removal of condensate water from the indoor coil. In order to provide proper condensate flow, a drain trap is supplied and shipped loose inside the unit for field installation. (Do not reduce the drain line size). efrigerant flow control is achieved by use of TXV. Some heat pump models also have a suction line accumulator installed between the reversing valve and the compressor. The object of the accumulator is to: 1. Provide a liquid refrigerant storage vessel during prolonged system off cycles.. Store excess liquid refrigerant not needed by the system while running.. eturn oil and saturated vapor to the compressor at a controlled rate.. etain stored excess refrigerant during a sudden system pressure fluctuation such as seen in defrost cycles. efrigerant flow control is achieved by use of TXV. These models use the FasTest Access Fitting System, with a saddle that is either soldered to the suction and liquid lines or is fastened with a locking nut to the access fitting box (core) and then screwed into the saddle. Do not remove the core from the saddle until the refrigerant charge has been removed. Failure to do so could result in property damage or personal injury. The single phase units use permanent split capacitor (PS) design compressors. Starting components are not required for these units. A low microfarad run capacitor assists the compressor to start and remains in the circuit during operation. GPH15 models The outdoor fan motors are single phase capacitor type motors. GPH15 M series units have EEM indoor blower motors that are energized by a V signal from the thermostat and are constant torque motors with very low power consumption. EEM motors feature an integral control module. APH15 models The outdoor fan motors are single phase capacitor type motors on the APH15 models. APH15 units have EM indoor blower motors that are energized by a low voltage signal from the interface board. EM motors are constant FM motors with very low power consumption. APH15 models are equipped with compressor sound blankets. *PH15 models Air for condensing (cooling cycle) or evaporation (heating cycle) is drawn through the outdoor coil by a propeller fan, and is discharged vertically out the top of the unit. The outdoor coil is designed for.0 static. No additional restriction (ductwork) shall be applied. onditioned air is drawn through the filter(s), field installed, across the coil and back into the conditioned space by the indoor blower. Package Heat Pump indoor sections are designed to accept optional components such as auxiliary electric heaters and circuit breakers. Provisions for these components have been made at time of manufacture. *PH15 series package units use the ompliant Scroll compressor; there are a number of design characteristics which are different from the traditional reciprocating compressor. - Due to their design Scroll compressors are inherently more tolerant of liquid refrigerant. NOTE: Even though the compressor section of a Scroll compressor is more tolerant of liquid refrigerant, continued flood back or flooded start conditions may wash oil from the bearing surfaces causing premature bearing failure. - These Scroll compressors use "POE" or polyolester oil which is NOT compatible with mineral oil based lubricants like GS. "POE" oil must be used if additional oil is required. - ompliant scroll compressors perform quiet shutdowns that allow the compressor to restart immediately without the need for a time delay. This compressor will restart even if the system has not equalized. - Operating pressures and amp draws may differ from standard reciprocating compressors. This information may be found in the ooling Performance Data section. *PH15**M1*, 8, 9 and 60 model package units use a stage scroll compressor. The basic scroll design has been modified with the addition of an internal unloading mechanism that opens a by-pass port in the first compression pocket, effectively reducing the displacement of the scroll. The opening and closing of the by-pass port is controlled by an internal electrically operated solenoid.

5 PODUT DESIGN Minimum clearances are required to avoid air recirculation and keep the unit operating at peak efficiency. The ZPS modulated scroll uses a single step of unloading to go from full capacity to approximately 67% capacity. A single speed, high efficiency motor continues to run while the scroll modulates between the two capacity steps. oof urb Location and learances NOTE: To ensure proper condensate drainage, unit must be installed in a level position. ooftop Installation - -Multi-positional (M) NOTE: To ensure proper condensate drainage, unit must be installed in a level position. In installations where the unit is installed above ground level and not serviceable from the ground (Example: roof top installations) the installer must provide service platform for service person with rails or guards in accordance with local codes or ordinances, or, in their absence, with the latest edition of the Uniform Mechanical ode Section 05. NOTE: Unit can also use roof curb (and platform for leveling, where necessary) to utilize bottom discharge. WANING TO PEVENT POSSIE POPETY DAMAGE, THE UNIT SHOULD EMAIN IN AN UPIGHT POSITION DUING ALL IGGING AND MOVING OPEATIONS. TO FAILITATE LIFTING AND MOVING IF A ANE IS USED, PLAE THE UNIT IN AN ADEQUATE AE SLING. Outside Slab Installation -Multi-positional (M) NOTE: oof overhang should be no more than 6" and provisions made to deflect the warm discharge air out from the overhang. IMPOTANT: If using bottom discharge with roof curb, ductwork should be attached to the curb prior to installing the unit. efer to oof curb Installation Instructions for proper curb installation. urbing must be installed in compliance with the National oofing ontractors Association Manual. 5

6 PODUT DESIGN HK ELETIAL DATA Minimum ircuit Ampacity at 08 / 0V ircuit #1 ircuit # Maximum Overcurrent Protection (amps) at 08 / 0V Minimum ircuit Ampacity at 08 / 0V *PH15[-60]M1* Maximum Overcurrent Protection (amps) at 08 / 0V Actual kw & BTU at 0V *PH15M1* / *A HK05A,A / 7 0 / / 16,00 HK08A,A / 8 0 / /,800 HK10A,A 5 / / /,00 *PH150M1* / *A HK05A,A / 7 0 / / 16,00 HK08A,A / 9 0 / /,800 HK10A,A 5 / 5 60 / /,00 HK15A,A 5 / 5 60 / 60 / 5 0 / / 8,600 *PH156M1* / *A HK05A,A / 7 0 / / 16,00 HK08A,A / 9 0 / /,800 HK10A,A 5 / 5 60 / /,00 HK15A,A 5 / 5 60 / 60 / 5 0 / / 8,600 *PH15M1* / *A HK05A,A / 7 0 / / 16,00 HK08A,A / 9 0 / /,800 HK10A,A 5 / 5 60 / /,00 HK15A,A 5 / 5 60 / 60 / 5 0 / / 8,600 *PH159M1* / *A HK05A,A 5 / 8 0 / / 16,00 HK08A,A / 0 0 / /,800 HK10A,A 6 / 5 60 / /,00 HK15A,A 6 / 5 60 / 60 / 5 0 / / 8,600 HK0A,A 6 / 5 60 / 60 / 9 60 / / 66,500 *PH1560M1* / *A HK05A,A 6 / 0 0 / / 16,00 HK08A,A 6 / 0 0 / /,800 HK10A,A 8 / 5 60 / /,00 HK15A,A 8 / 5 60 / 60 / 5 0 / / 8,600 HK0A,A 8 / 5 60 / 60 / 9 60 / / 66,500 IMPOTANT NOTE: A separate power supply is required for the HK heater kit. Heating kw orrection Factor Supply Votage orrection Factor Multiply rated kw by correction factor to get actual kw WANING All wires and overcurrent protection devices are sized for use with electric heaters only and without refrigeration. If heaters are not installed with above wire size, overheating and fire could occur. See PAKAGE UNIT SPEIFIATIONS section for minimum circuit ampacity and maximum overcurrent protection during refrigeration cycle. 6

7 PODUT DIMENSIONS *PH15[-60]M1* 7 51 POWE WIE ENTANE 1/8 1/8 1 /8 5 ½ 16? A 6 ½ 8 16 B SUTION/LIQUID PESSUE POT ONDENSATE DAIN ONNETION / NPT FEMALE 18 7/8? B ONTOL WIE ENTANE SUPPLY ETUN OWE AESS PANEL MEDIUM HASSIS *PH15M1* *PH150M1* *PH156M1* LAGE HASSIS *PH15M1* *PH159M1* *PH1560M1* 7

8 PAKAGE HEAT MP SPEIFIATIONS GPH15M1* GPH15M1 AD GPH150M1* GPH15[-6]M1A* GPH150M1 AD GPH156M1* GPH156M1 AD OOLING OOLING APAITY, BTUH,000,000 9,000 9,000 5,00 5,00 APAITY SEE / EE 15.0 / / / / / / 11.5 HEATING BTU/h (7 ),00,00 7,00 7,00,00,00 ATING 5 / F 18,00 18,00 18,600 18,600 8,00 8,00 BTU/h (17 ) 1,500 1,500 15,00 15,00 18,600 18,600 HSPF UNIT VOLTAGE (NAMEPLATE) 08/ / / / / / EL ETIAL AMPS SPEIFIATION MIN IUIT AMPAITY MAX OVEUENT POTETION OMPESSO TYPE SOLL SOLL SOLL SOLL SOLL SOLL ATED LOAD AMPS LOKED OTO AMPS ONDENSE HOSEPOWE 1/ 1/ 1/ 1/ 1/ 1/ FAN MOTO PM FULL LOAD AMPS LOKED OTO AMPS ONDENSE FAN ADE DIAMETE (INHES) NUMBE OF ADES ONDENSE FAE AEA (SQ. FT.) OIL NUMBE OF OWS FINS PE INH EVAPOATO HOSEPOWE - NUMBE OF SPEEDS 1/ - 5 1/ - 5 1/ - 5 1/ - 5 1/ - 5 1/ - 5 OWE FULL LOAD AMPS MOTO LOKED OTO AMPS MOTO SPEED TAP - OOLING EEM T T T T T T PM 1,050 1,050 1,050 1,050 1,050 1,050 EVAPOATO DIAMETE X WIDTH (INHES) 10 x 9 10 x 9 10 x 9 10 x 9 10 x 9 10 x 9 OWE ATED SFM OOLING ,000 1,000 1,00 1,00 MAX EXTENAL STATI PESS ("w.c.) EVAPOATO FAE AEA (SQ. FT.) OIL NUMBE OF OWS FINS PE INH GENEAL FILTE SIZE * 0 x 0 x 1 0 x 0 x 1 5 x 5 x 1 5 x 5 x 1 5 x 5 x 1 5 x 5 x 1 INFOMATION DAIN SIZE (INHES) /" /" /" /" /" /" EXPANSION DEVIE ONDENSE EVAPOATO TXV TXV PISTON TXV EFIGEANT HAGE 10A (OZS.) POWE SUPPLY ONDUIT KNOKOUT SIZE (INHES) /, 1, 1-1/ /, 1, 1-1/ /, 1, 1-1/ /, 1, 1-1/ /, 1, 1-1/ /, 1, 1-1/ LOW VOLTAGE ONDUIT KNOKOUT SIZE (INHES) 1/ 1/ 1/ 1/ 1/ 1/ LO PESSUE SWITH OPENS / LOSES PSIG / 50 / 50 / 50 / 50 / 50 / 50 HI PESSUE SWITH OPENS / LOSES PSIG 660 / / / / / / 0 SHIPPING WEIGHT (LBS.) OPEATING WEIGHT (LBS.) TXV TXV PISTON TXV TXV TXV PISTON TXV (1) Minimum ircuit Ampacity calculated as: (1.5 x irculator Blower Amps) + I.D. Blower Amps. () Maximum Overcurrent Protection Device: MUST use Time Delay Fuse or HA type ircuit Breaker of the same size as noted. 8 * alculated external filter size based on air velocity of 00 ft/min. Wire size should be determined in accordance with National Electrical odes. Extensive wire runs will require larger wire sizes. Unit specifications are subject to change without notice. ALWAYS refer to the units serial plate for the most up-to-date general and electrical information. IMPOTANT: While this data is presented as a guide, it is important to electrically connect the unit and properly size wires and fuses/circuit breakers in accordance with the National Electrical ode and/or all local codes. Data shown is w/o electric heaters.

9 PAKAGE HEAT MP SPEIFIATIONS GPH15[-60]M1AB//D GPH15M1* GPH159M1 AB/A GPH159M1 AD GPH1560M1 AB/A GPH1560M1 AD OOLING OOLING APAITY, BTUH 0,000 6,000 6,000 55,500 55,500 APAITY SEE / EE 15.0 / / / / / 10. HEATING BTU/h (7 ) 9,000 5,500 5,500 56,000 56,000 ATING 5 / F 7,800,000,000 5,700 5,700 BTU/h (17 ),000 5,000 5,000 1,00 1,00 HSPF UNIT VOLTAGE (NAMEPLATE) 08/ / / / / ELETIAL AMPS SPEIFIATION MIN IUIT AMPAITY MAX OVEUENT POTETION OMPESSO TYPE SOLL SOLL SOLL SOLL SOLL ATED LOAD AMPS LOKED OTO AMPS ONDENSE HOSEPOWE 1/ 1/ 1/ 1/ 1/ FAN MOTO PM FULL LOAD AMPS LOKED OTO AMPS ONDENSE FAN ADE DIAMETE (INHES) NUMBE OF ADES ONDENSE FAE AEA (SQ. FT.) OIL NUMBE OF OWS FINS PE INH EVAPOATO HOSEPOWE - NUMBE OF SPEEDS / - 5 / - 5 / OWE FULL LOAD AMPS MOTO LOKED OTO AMPS MOTO SPEED TAP - OOLING EEM T1 (Low) T (High) T1 (Low) T (High) T1 (Low) T (High) T1 (Low) T (High) T1 (Low) T (High) PM 1,050 1,050 1,050 1,050 1,050 EVAPOATO DIAMETE X WIDTH (INHES) 10 x 9 10 x 9 10 x 9 10 x 9 10 x 9 OWE ATED SFM OOLING 1,50 1,50 1,50 1,800 1,800 MAX EXTENAL STATI PESS ("w.c.) EVAPOATO FAE AEA (SQ. FT.) OIL NUMBE OF OWS FINS PE INH GENEAL FILTE SIZE * () 0 x 0 x 1 () 0 x 0 x 1 () 0 x 0 x 1 () 0 x 5 x 1 () 0 x 5 x 1 INFOMATION DAIN SIZE (INHES) /" /" /" /" /" EXPANSION DEVIE TXV TXV TXV TXV TXV EFIGEANT HAGE 10A (OZS.) POWE SUPPLY ONDUIT KNOKOUT SIZE (INHES) /, 1, 1-1/ /, 1, 1-1/ /, 1, 1-1/ /, 1, 1-1/ /, 1, 1-1/ LOW VOLTAGE ONDUIT KNOKOUT SIZE (INHES) 1/ 1/ 1/ 1/ 1/ LO PESSUE SWITH OPENS / LOSES PSIG / 50 / 50 / 50 / 50 / 50 HI PESSUE SWITH - OPENS PSIG OPENS / LOSES PSIG 660 / / / / / 0 SHIPPING WEIGHT (LBS.) OPEATING WEIGHT (LBS.) (1) Minimum ircuit Ampacity calculated as: (1.5 x irculator Blower Amps) + I.D. Blower Amps. () Maximum Overcurrent Protection Device: MUST use Time Delay Fuse or HA type ircuit Breaker of the same size as noted. * alculated external filter size based on air velocity of 00 ft/min. Wire size should be determined in accordance with National Electrical odes. Extensive wire runs will require larger wire sizes. Unit specifications are subject to change without notice. ALWAYS refer to the units serial plate for the most up-to-date general and electrical information. IMPOTANT: While this data is presented as a guide, it is important to electrically connect the unit and properly size wires and fuses/circuit breakers in accordance with the National Electrical ode and/or all local codes. Data shown is w/o electric heaters. 9

10 PAKAGE HEAT MP SPEIFIATIONS APH15[-6]M1A* APH15M1* APH15M1 AD APH150M1* APH150M1 AD APH156M1* APH156M1 AD OOLING OOLING APAITY, BTUH,000,000 9,000 9,000 5,00 5,00 APAITY SEE / EE 15.0 / / / / / / 11.5 HEATING BTU/h (7 ),00,00 7,00 7,00,00,00 ATING 5 / F 18,00 18,00 18,600 18,600 8,00 8,00 BTU/h (17 ) 1,500 1,500 15,00 15,00 18,600 18,600 H SPF UNIT VOLTAGE (NAMEPLATE) 08/ / / / / / ELE TIAL AMPS SPEIFIATION MIN IUIT AMPAITY MAX OVEUENT POTETION OMPESSO TYPE SOLL SOLL SOLL SOLL SOLL SOLL ATED LOAD AMPS LOKED OTO AMPS ONDENSE HOSEPOWE 1/ 1/ 1/ 1/ 1/ 1/ FAN MOTO PM FULL LOAD AMPS LOKED OTO AMPS ONDENSE FAN ADE DIAMETE (INHES) NUMBE OF ADES ONDENSE FAE AEA (SQ. FT.) OIL NUMBE OF OWS FINS PE INH EVAPOATO HOSEPOWE - NUMBE OF SPEEDS 1/ - VA. 1/ - VA. 1/ - VA. 1/ - VA. 1/ - VA. 1/ - VA. OWE FULL LOAD AMPS MOTO LOKED OTO AM PS MOTO SPEED TAP - OOLING - EM B B B B B B PM 1,050 1,050 1,050 1,050 1,050 1,050 EVAPOATO DIAMETE X WIDTH (INHES) 10 x 9 10 x 9 10 x 9 10 x 9 10 x 9 10 x 9 OWE ATED SFM OOLING ,000 1,000 1,00 1,00 MAX EXTENAL STATI PESS ("w.c.) EVAPOATO FAE AEA (SQ. FT.) OIL NUMBE OF OWS FINS PE INH GENEAL FILTE SIZE * 0 x 0 x 1 0 x 0 x 1 5 x 5 x 1 5 x 5 x 1 5 x 5 x 1 5 x 5 x 1 IN FOMATION DAIN SIZE (INHES) /" /" /" /" /" /" EXPANSION DEVIE ONDENSE EVAPOATO TXV TXV PISTON TXV TXV TXV PISTON TXV TXV TXV PISTON TXV EFIGEANT HAGE 10A (OZS.) POWE SUPPLY ONDUIT KNOKOUT SIZE (INHES) /, 1, 1-1/ /, 1, 1-1/ /, 1, 1-1/ /, 1, 1-1/ /, 1, 1-1/ /, 1, 1-1/ LOW VOLTAGE ONDUIT KNOKOUT SIZE (INHES) 1/ 1/ 1/ 1/ 1/ 1/ LO PESSUE SWITH OPENS / LOSES PSIG / 50 / 50 / 50 / 50 / 50 / 50 HI PESSUE SWITH - OPENS PSIG OPENS / LOSES PSIG 660 / / / / / / 0 SHIPPING WEIGHT (LBS.) OPEATING WEIGHT (LBS.) (1) Minimum ircuit Ampacity calculated as: (1.5 x irculator Blower Amps) + I.D. Blower Amps. () Maximum Overcurrent Protection Device: MUST use Time Delay Fuse or HA type ircuit Breaker of the same size as noted. * alculated external filter size based on air velocity of 00 ft/min. Wire size should be determined in accordance with National Electrical odes. Extensive wire runs will require larger wire sizes. Unit specifications are subject to change without notice. ALWAYS refer to the units serial plate for the most up-to-date general and electrical information. IMPOTANT: While this data is presented as a guide, it is important to electrically connect the unit and properly size wires and fuses/circuit breakers in accordance with the National Electrical ode and/or all local codes. Data shown is w/o electric heaters. 10

11 PAKAGE HEAT MP SPEIFIATIONS APH15[-60]M1AB//D APH15M1* APH159M1 AB/A APH159M1 AD APH1560M1 AB/A APH1560M1 AD OOLING OOLING APAITY, BTUH 0,000 6,000 6,000 55,600 55,600 APAITY SEE / EE 15.0 / / / / / 10. HEATING BTU/h (7 ) 9,000 5,500 5,500 56,000 56,000 ATING 5 / F 7,800,000,000 5,700 5,700 BTU/h (17 ),000 5,000 5,000 1,00 1,00 HSPF UNIT VOLTAGE (NAMEPLATE) 08/ / / / / ELETIAL AMPS SPEIFIATION MIN IUIT AMPAITY MAX OVEUENT POTETION OMPESSO TYPE SOLL SOLL SOLL SOLL SOLL ATED LOAD AMPS LOKED OTO AMPS ONDENSE HOSEPOWE 1/ 1/ 1/ 1/ 1/ FAN MOTO PM FULL LOAD AMPS LOKED OTO AMPS ONDENSE FAN ADE DIAMETE (INHES) NUMBE OF ADES ONDENSE FAE AEA (SQ. FT.) OIL NUMBE OF OWS FINS PE INH EVAPOATO HOSEPOWE - NUMBE OF SPEEDS / - VA. / - VA. / - VA. 1 - VA. 1 - VA. OWE FULL LOAD AMPS MOTO LOKED OTO AMPS MOTO SPEED TAP - OOLING - EM B B B B B PM 1,050 1,50 1,50 1,050 1,050 EVAPOATO DIAMETE X WIDTH (INHES) 10 x 9 10 x 9 10 x 9 10 x 9 10 x 9 OWE ATED SFM OOLING 1,50 1,50 1,50 1,800 1,800 MAX EXTENAL STATI PESS ("w.c.) EVAPOATO FAE AEA (SQ. FT.) OIL NUMBE OF OWS FINS PE INH GENEAL FILTE SIZE * () 0 x 0 x 1 () 0 x 0 x 1 () 0 x 0 x 1 () 0 x 5 x 1 () 0 x 5 x 1 INFOMATION DAIN SIZE (INHES) /" /" /" /" /" EXPANSION DEVIE TXV TXV TXV TXV TXV EFIGEANT HAGE 10A (OZS.) POWE SUPPLY ONDUIT KNOKOUT SIZE (INHES) /, 1, 1-1/ /, 1, 1-1/ /, 1, 1-1/ /, 1, 1-1/ /, 1, 1-1/ LOW VOLTAGE ONDUIT KNOKOUT SIZE (INHES) 1/ 1/ 1/ 1/ 1/ LO PESSUE SWITH OPENS / LOSES PSIG / 50 / 50 / 50 / 50 / 50 HI PESSUE SWITH - OPENS PSIG OPENS / LOSES PSIG 660 / / / / / 0 SHIPPING WEIGHT (LBS.) OPEATING WEIGHT (LBS.) (1) Minimum ircuit Ampacity calculated as: (1.5 x irculator Blower Amps) + I.D. Blower Amps. () Maximum Overcurrent Protection Device: MUST use Time Delay Fuse or HA type ircuit Breaker of the same size as noted. * alculated external filter size based on air velocity of 00 ft/min. Wire size should be determined in accordance with National Electrical odes. Extensive wire runs will require larger wire sizes. Unit specifications are subject to change without notice. ALWAYS refer to the units serial plate for the most up-to-date general and electrical information. IMPOTANT: While this data is presented as a guide, it is important to electrically connect the unit and properly size wires and fuses/circuit breakers in accordance with the National Electrical ode and/or all local codes. Data shown is w/o electric heaters. 11

12 AESSOIES Part Number AESSOIES - GP/GPH****M MODELS Description *PH15[-60]M1* OT18-60A OT/EH18-60 HK PG101/10/10 PEHH101/10 PEHH10 PEH101/10 PEH10 PGMDD101/10 PGMDD10 PGMDH10 PGMDH10 PGMDMD101/10 PGMDMD10 PGMDMH10 PGMDMH10 GP1MED10 GP1MED10 GPH1MED10 GPH1MED10 GPH1MF10 GPH1MF10 GPGHF SQPG101/10 SQPG10 SQPGH101/10 SQPGH10 DK6 DK6515 DK650 DK655 DK87 DK87515 DK8750 DK8755 Outdoor Thermostat Kit w/lockout Stat Emergency Heat elay Kit Electric Heat Kit oof urb Horizontal Economizer For Heat Pump, Small and Medium hassis Horizontal Economizer For Heat Pump, Large hassis Horizontal Economizer For A/, Small and Medium hassis Horizontal Economizer For A/, Large hassis Manual 5% Fresh Air Damper Downflow Application, Small and Medium hassis Manual 5% Fresh Air Damper Downflow Application, Large hassis Manual 5% Fresh Air Damper Horizontal Application, Medium hassis Manual 5% Fresh Air Damper Horizontal Application, Large hassis Motorized 5% Fresh Air Damper Downflow Application,Small and Medium hassis Motorized 5% Fresh Air Downflow Application, Large hassis Motorized 5% Fresh Air Damper Horizontal Application, Medium hassis Motorized 5% Fresh Air Damper Horizontal Application, Large hassis Downflow Economizer For A/, Medium hassis Downflow Economizer For A/, Large hassis Downflow Economizer For Heat Pump, Medium hassis Downflow Economizer For Heat Pump, Large hassis Internal Filter ack, Medium hassis Internal Filter ack, Large hassis External Horizontal Filter ack for Goodman/Amana Gas/Electric and Multi-position Package Units All hassis Square to ound Adapter w/ 16" ound Downflow Application, Medium hassis Square to ound Adapter w/ 18" ound Downflow Application, Large hassis Square to ound Adapter w/ 16" ound Horizontal Application, Medium hassis Square to ound Adapter w/ 18" ound Horizontal Application, Large hassis Flush Mount oncentric Duct Kit Flush Mount oncentric Duct Kit w/ Filter Step Down oncentric Duct Kit Step Down oncentric Duct Kit w/ Filter Flush Mount oncentric Duct Kit Flush Mount oncentric Duct Kit w/ Filter Step Down oncentric Duct Kit Step Down oncentric Duct Kit w/ Filter 1

13 OWE PEFOMANE DATA GPH15[-60]M1* Dry oil Data Model Speed Volts E.S.P (In. of H O) T1 (G) 0 FM WATTS T / T FM (W) WATTS T / T5 (Y) 0 FM WATTS T1 (G) 0 FM WATTS T / T FM (W) WATTS T / T5 (Y) T1 (G) 0 0 FM FM WATTS WATTS T / T FM (W) WATTS T / T5 (Y) T1 (G) 0 0 FM FM WATTS Watts T (Y) / T FM (W) Watts T / T5 FM (HS) Watts T1 (G) T (Y) 0 0 FM FM Watts Watts T (W) 0 FM Watts T (YHS) 0 FM Watts T5 FM (S) Watts T1 (G) 0 FM WATTS T / T FM (W) WATTS T / T5 (Y) 0 FM WATTS GPH15M1* GPH150M1* GPH156M1* GPH15M1* GPH159M1* GPH1560M1* NOTES: Data shown is Dry oil. Wet oil Pressure Drop is approximate. 0.1" H O, for row indoor coil; 0. H O, for row indoor coil; and 0. H O, for row indoor coil. Data shown does not include filter pressure drop, approx H O. ALL MODELS SHOULD UN NO LESS THAN 50 FM / TON. educe airflow by % for 08V operation. 1

14 OWE PEFOMANE DATA APH15[-60]M1* Evaporator Blower Specifications with EM Motors APH15M1 APH150M1 ooling/hp Adjust Electric Adjust ooling/hp Adjust Electric Adjust FM* FM* FM* Speed Tap Heat Tap Speed Tap Heat Tap FM* D Minus 60 D Minus 60 D Minus 70 D Minus 70 D Normal 700 D Normal 700 D Normal 800 D Normal 800 D Plus 770 D Plus 770 D Plus 880 D Plus 880 Minus 7 Minus 7 Minus 900 Minus 900 Normal 85 Normal 85 Normal 1,000 Normal 1,000 Plus 908 Plus 908 Plus 1,100 Plus 1,100 B Minus 855 B Minus 855 B Minus 990 B Minus 990 B Normal 950 B Normal 950 B Normal 1,100 B Normal 1,100 B Plus 1,05 B Plus 1,05 B Plus 1,10 B Plus 1,10 A Minus 95 A Minus 95 A Minus 1,15 A Minus 1,15 A Normal 1,050 A Normal 1,050 A Normal 1,50 A Normal 1,50 A Plus 1,155 A Plus 1,155 A Plus 1,75 A Plus 1, ESP ESP APH156M1 ooling/hp Adjust Electric Adjust FM* Speed Tap Heat Tap FM* D Minus 70 D Minus 70 D Normal 800 D Normal 800 D Plus 880 D Plus 880 Minus 900 Minus 900 Normal 1,000 Normal 1,000 Plus 1,100 Plus 1,100 B Minus 990 B Minus 990 B Normal 1,100 B Normal 1,100 B Plus 1,10 B Plus 1,10 A Minus 1,15 A Minus 1,15 A Normal 1,50 A Normal 1,50 A Plus 1,75 A Plus 1, ESP APH158M1 ooling/hp Adjust Electric Adjust FM* Speed Tap Heat Tap FM* D Minus 1,10 D Minus 1,10 D Normal 1,5 D Normal 1,5 D Plus 1,8 D Plus 1,8 Minus 1,60 Minus 1,60 Normal 1,00 Normal 1,00 Plus 1,50 Plus 1,50 B Minus 1,50 B Minus 1,50 B Normal 1,700 B Normal 1,700 B Plus 1,870 B Plus 1,870 A Minus 1,60 A Minus 1,60 A Normal 1,800 A Normal 1,800 A Plus 1,980 A Plus 1, ESP APH15M1 APH159M1 ooling/hp Adjust Electric Adjust FM* Speed Tap Heat Tap FM* D Minus 1,10 D Minus 1,10 D Normal 1,5 D Normal 1,5 D Plus*** 1,8 D Plus 1,8 Minus** 1,60 Minus** 1,60 Normal 1,00 Normal 1,00 Plus 1,50 Plus 1,50 B Minus 1,50 B Minus 1,50 B Normal 1,700 B Normal 1,700 B Plus 1,870 B Plus 1,870 A Minus 1,60 A Minus 1,60 A Normal 1,800 A Normal 1,800 A Plus 1,980 A Plus*** 1, ESP ** DENOTES FATOY SETTING FO APH15M1 *** DENOTES FATOY SETTING FO APH159M1 APH1560M1 ooling/hp Adjust Electric Adjust FM* Speed Tap Heat Tap FM* D Minus 1,60 D Minus 1,60 D Normal 1,00 D Normal 1,00 D Plus 1,50 D Plus 1,50 Minus 1,0 Minus 1,0 Normal 1,600 Normal 1,600 Plus 1,760 Plus 1,760 B Minus 1,60 B Minus 1,60 B Normal 1,800 B Normal 1,800 B Plus 1,980 B Plus 1,980 A Minus 1,800 A Minus 1,800 A Normal,000 A Normal,000 A Plus,00 A Plus, ESP 1

15 OWE PEFOMANE DATA APH15[-60]M1* Dipswtich Settings Model APH15 APH150 APH156 APH15 APH159 Speed Tap Switch 1 Switch Electric Heat FM A OFF OFF 1050 (F) B ON OFF 950 OFF ON 85 D ON ON 700 A OFF OFF 150 (F) B ON OFF 1,100 OFF ON 1,000 D ON ON 800 A OFF OFF 150 (F) B ON OFF 1100 OFF ON 1000 D ON ON 800 A OFF OFF 1800 (F) B ON OFF 1700 OFF ON 100 (F) * D ON ON 15 A OFF OFF 000 (F) APH1560 B ON OFF 1800 OFF ON 1600 D ON ON 100 (F) Factory Setting (F)* APH15 Model APH15 APH150 APH156 APH15 APH159 Speed Tap Switch 5 Switch 6 ooling/hp FM A OFF OFF 1050 (F) B ON OFF 950 OFF ON 85 D ON ON 700 A OFF OFF 150 (F) B ON OFF 1,100 OFF ON 1,000 D ON ON 800 A OFF OFF 150 (F) B ON OFF 1100 OFF ON 1000 D ON ON 800 A OFF OFF 1800 (F) B ON OFF 1700 OFF ON 100 (F) * D ON ON 15 (F) ** A OFF OFF 000 (F) B ON OFF 1800 APH1560 OFF ON 1600 D ON ON 100 (F) Factory Setting (F)* APH15 (F)** APH159 Important: Disconnect power to unit before moving jumper to prevent damage to TAP board APH15, 8-60: low-stage cool will be 70% of high-stage cool. DIP Switch Settings for Single & Two-Stage Thermostats MODEL APH15** SWITH SWITH THEMOSTAT N/A ON Single Stage N/A OFF Two-Stage Adjustments Through Dip Switch ombinations 7-8 SWITH SWITH FM % On Off Normal Off Off -10% Off On 15

16 OWE PEFOMANE DATA BTU OUTT vs TEMPEATUE ISE HAT 600 FM FM FOMULAS BTU OUTT = FM x 1.08 x ISE ISE = BTU OUTT 1.08 FM OUTT BTU/H x TEMPEATUE ISE

17 OOLING PEFOMANE DATA *PH15M1* MODEL: *PH15M1* EXPANDED PEFOMANE DATA OOLING OPEATION Outdoor Ambient Temperature Entering Indoor Wet Bulb Temperature IDB* Airflow MBh S/T Delta T KW AMPS HI P LO P MBh S/T Delta T KW AMPS HI P LO P MBh S/T Delta T KW AMPS HI P LO P MBh S/T Delta T KW AMPS HI P LO P MBh S/T Delta T KW AMPS HI P LO P MBh S/T Delta T KW AMPS HI P LO P * Entering Indoor Dry Bulb Temperature NOTE: Shaded area is AA (TVA) conditions KW = Total system pow er High and low pressures are measured at the liquid and suction access fittings. AMPS: Unit amps (comp.+ evaporator + condenser fan motors) 17

18 OOLING PEFOMANE DATA *PH15M1* MODEL: *PH15M1* EXPANDED PEFOMANE DATA OOLING OPEATION Outdoor Ambient Temperature Entering Indoor Wet Bulb Temperature IDB* Airflow MBh S/T Delta T KW AMPS HI P LO P MBh S/T Delta T KW AMPS HI P LO P MBh S/T Delta T KW AMPS HI P LO P MBh S/T Delta T KW AMPS HI P LO P MBh S/T Delta T KW AMPS HI P LO P MBh S/T Delta T KW AMPS HI P LO P * Entering Indoor Dry Bulb Temperature NOTE: Shaded area is AHI ating onditions KW = Total system pow er High and low pressures are measured at the liquid and suction access fittings. AMPS: Unit amps (comp.+ evaporator + condenser fan motors) 18

19 OOLING PEFOMANE DATA *PH150M1* MODEL: *PH150M1** EXPANDED PEFOMANE DATA OOLING OPEATION Outdoor Ambient Temperature Entering Indoor Wet Bulb Temperature IDB* Airflow MBh S/T Delta T KW AMPS HI P LO P MBh S/T Delta T KW AMPS HI P LO P MBh S/T Delta T KW AMPS HI P LO P MBh S/T Delta T KW AMPS HI P LO P MBh S/T Delta T KW AMPS HI P LO P MBh S/T Delta T KW AMPS HI P LO P * Entering Indoor Dry Bulb Temperature NOTE: Shaded area is AA (TVA) conditions KW = Total system pow er High and low pressures are measured at the liquid and suction access fittings. AMPS: Unit amps (comp.+ evaporator + condenser fan motors) 19

20 OOLING PEFOMANE DATA *PH150M1* MODEL: *PH150M1** EXPANDED PEFOMANE DATA OOLING OPEATION Outdoor Ambient Temperature Entering Indoor Wet Bulb Temperature IDB* Airflow MBh S/T Delta T KW AMPS HI P LO P MBh S/T Delta T KW AMPS HI P LO P MBh S/T Delta T KW AMPS HI P LO P NOTE: Shaded area reflects AI rating conditions MBh S/T Delta T KW AMPS HI P LO P MBh S/T Delta T KW AMPS HI P LO P MBh S/T Delta T KW AMPS HI P LO P * Entering Indoor Dry Bulb Temperature NOTE: Shaded area is AHI ating onditions KW = Total system pow er High and low pressures are measured at the liquid and suction access fittings. AMPS: Unit amps (comp.+ evaporator + condenser fan motors) 0

21 OOLING PEFOMANE DATA *PH156M1* MODEL: *PH156M1* EXPANDED PEFOMANE DATA OOLING OPEATION Outdoor Am bient Temperature Entering Indoor Wet Bulb Temperature IDB* Airflow MBh S/T Delta T KW AMPS HI P LO P MBh S/T Delta T KW AMPS HI P LO P MBh S/T Delta T KW AMPS HI P LO P MBh S/T Delta T KW AMPS HI P LO P MBh S/T Delta T KW AMPS HI P LO P MBh S/T Delta T KW AMPS HI P LO P * Entering Indoor Dry Bulb Temperature NOTE: Shaded area is AA (TVA) conditions KW = Total system pow er High and low pressures are measured at the liquid and suction access fittings. AMPS: Unit amps (comp.+ evaporator + condenser fan motors) 1