Operating Parameters SUNNY BOY/SUNNY MINI CENTRAL/WINDY BOY

Transcription

1 Operating Parameters SUNNY BOY/SUNNY MINI CENTRAL/WINDY BOY Technical Description SB_SMC_WB_Par-TEN Version 5.0 EN

2

3 SMA Solar Technology AG Table of Contents Table of Contents 1 Notes on this Manual Area of Validity Target Group Additional Information Symbols Used Safety Instructions Explanation of the Operating Parameters Setting the Country Standard Value Ranges and Factory Settings Sunny Boy Sunny Boy 1200/ Sunny Boy 2100TL Sunny Boy 2500/ Sunny Boy 3300/ Sunny Boy 3300TL HC Sunny Mini Central Sunny Mini Central 4600A/5000A/6000A Sunny Mini Central 7000HV/7000HV Sunny Mini Central 6000TL/7000TL/8000TL Sunny Mini Central 9000TL/10000TL/11000TL Sunny Mini Central 9000TL/10000TL/11000TL with Reactive Power Control Windy Boy Windy Boy 1100LV Windy Boy 1200/ Windy Boy 2500/ Windy Boy 3300/ Windy Boy 5000A/6000A Contact Technical Description SB_SMC_WB_Par-TEN

4 Table of Contents SMA Solar Technology AG 4 SB_SMC_WB_Par-TEN Technical Description

5 SMA Solar Technology AG Notes on this Manual 1 Notes on this Manual 1.1 Area of Validity This document describes the operating parameters including value ranges and factory settings for the following SMA inverters: Sunny Boy Windy Boy Sunny Mini Central SB 1200 WB 1200 SMC 4600A SB 1700 WB 1700 SMC 5000A SB 2100TL WB 2500 SMC 6000A SB 2500 WB 3000 SMC 7000HV SB 3000 WB 3300 SMC 7000HV-11 SB 3300TL HC WB 3800 SMC 6000TL SB 3300 WB 5000A SMC 7000TL SB 3800 WB 6000A SMC 8000TL SMC 9000TL-10 SMC 10000TL-10 SMC 11000TL-10 SMC 9000TLRP-10 SMC 10000TLRP-10 SMC 11000TLRP Target Group This document is intended for installers and operators of the inverter. Some tasks described in this document may only be carried out by electrically qualified persons. 1.3 Additional Information For information on assembly, installation, commissioning, and maintenance of the inverter as well as device-specific technical data refer to the installation guide of the respective inverter. You will find information on operating the inverter in the user manual of the respective inverter. Technical Description SB_SMC_WB_Par-TEN

6 Notes on this Manual SMA Solar Technology AG 1.4 Symbols Used The following types of safety instructions and general information are used in this manual: DANGER! G "DANGER" indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING! "WARNING" indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION! "CAUTION" indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE! "NOTICE" indicates a situation that can result in property damage, if not avoided. Information Information provides tips that are valuable for the optimal installation and operation of your product. 6 SB_SMC_WB_Par-TEN Technical Description

7 SMA Solar Technology AG Safety Instructions 2 Safety Instructions The various operating parameters control the functionality of the inverter. They can only be viewed and changed using a communication device or communication software. Some parameters can only be viewed by an installer (grayed-out parameters). The so-called installer password is required for this. Parameters designated with * are safety-related grid monitoring parameters (SMA Grid Guard parameters). In order to change SMA Grid Guard parameters, you will need to enter the SMA Grid Guard Code. The application form is located in the download area at in the "Certificate" category for each inverter. DANGER! Danger to life through changing the inverter's internal safety specifications. Unauthorized changes to the SMA Grid Guard parameters void the operating license. Only change SMA Grid Guard parameters with express permission of the utility operator. Parameter Factory Settings You can see the standard to which the inverter was set upon delivery from the type plate and the supplementary document with the factory settings. Technical Description SB_SMC_WB_Par-TEN

8 Explanation of the Operating Parameters SMA Solar Technology AG 3 Explanation of the Operating Parameters Name ACVtgRPro* AID-Esk-Alpha* AntiIsland-Ampl* AntiIsland-Freq* AntiIsland-Lim* Control DC-Offset_Max* Default* dfac-max* DGS-HystVolNom* Description Voltage surge protection (only relevant for Germany). In Germany, Sunny Boy and Sunny Mini Central inverters can feed into the public grid with up to 260 V AC. However, the DIN VDE standard stipulates that the 10-minute AC voltage average may not exceed 253 V. If the 10-minute average exceeds the threshold value of 253 V, the inverter will disconnect from the grid. As soon as the 10-minute average returns to a value of less than 253 V, the inverter will continue to feed power into the grid. If voltage surge protection is not required in the relevant grid area (outside Germany), it can be deactivated by presetting the LDVtgC parameter. In this case, only the quick disconnection will be active, which can be configured through the Vac-Max parameter. Gain factor of the escalating anti-island process Amplification of the anti-island process (alternative anti-islanding process, which is deactivated for Germany). Repetition rate of the AntiIsland process (alternative anti-islanding process, which is deactivated for Germany). Maximum frequency, above and below the grid frequency of 50 or 60 Hz, before the grid monitoring system disconnects the device from the grid. Configuration of the current control. If the operating parameter "Control" is set to "Auto", the inverter automatically chooses the optimal type of current regulation. If the operating parameter "Control" is set to "Grid", the inverter regulates on the grid side. If set to "Bridge", the inverter regulates on the bridge side. This setting can help in the event of difficult grid conditions. Discuss the alteration of this parameter with the SMA Serviceline. Threshold value for the maximum direct current component in the AC current. Defines the country standard for adjusting country-specific information. You will find the procedure for changing country settings in section 4 Setting the Country Standard (page 15). Maximum change of grid frequency before the grid monitoring system disconnects the device from the grid. Hysteresis in percent. When the AC voltage exceeds the value set, the inverter starts feeding again. (only for SMC 9000TLRP-10, SMC 10000TLRP-10 and SMC 11000TLRP-10, SMC 7000HV-11) 8 SB_SMC_WB_Par-TEN Technical Description

9 SMA Solar Technology AG Explanation of the Operating Parameters Name DGS-PWMVolNom* dv V-Const dv-mpp Track dvref-mpp dzac-max E_total Fac-delta-* Fac-delta+* Fac-delta-Fast* Fac-delta+Fast* Fac-Limit delta Fac-Start delta Fac-Min-Fast-Tm* Fac-Max-Fast-Tm* Fac-Min-Tm* Fac-Max-Tm* Fac-Pderating Fac-Tavg Fan-Test Firmware-BFR Firmware-SRR GndFltRea Description Switch-off voltage in percent relative to VRef + VRefOfs. When the AC voltage drops below the value set here, the inverter will stop feeding. (only for SMC 9000TLRP-10, SMC 10000TLRP-10 and SMC 11000TLRP-10, SMC 7000HV-11) Device-internal parameter. Device-internal parameter. Device-internal parameter. Maximum change of grid impedance before the grid monitoring system disconnects the device from the grid. Total energy yield of the inverter. Changing this parameter may be necessary if you replace your inverter and want to use data from the old device. Maximum permissible frequency deviation (frequency increase protection and frequency drop protection), above (Fac-delta+, Fac-delta+Fast) and below (Fac-delta-, Fac-delta-Fast) a grid frequency of 50 or 60 Hz, before the grid monitoring system disconnects the device from the grid. For setting the frequency-dependent output derating in the "Off Grid" operating mode. More information on this subject can be found in the Sunny Island operation manual. Disconnection time for frequency increase protection (Fac-delta+, Fac-delta+Fast) and frequency drop protection (Fac-delta-, Fac-delta-Fast). Active power limitation depending on frequency. Averaging time of grid frequency measurement. By setting the "Fan-Test" parameter to "1", the functionality of the fan can be tested (only for inverters with fan). Firmware version of the operation control unit (BFR) Firmware version of the current control unit (SRR) Controls the behavior of the inverter in the event of a ground fault. GndFltWrn: If there is a ground fault, the inverter continues to feed into the grid. GndFltDscon: If there is a ground fault, the inverter disconnects from the grid. Technical Description SB_SMC_WB_Par-TEN

10 Explanation of the Operating Parameters SMA Solar Technology AG Name h_total Hardware-BFS I SearchNewMPP impedance test Inst.-Code KI-Wind-Reg KP-Wind-Reg LdVtgC* Memory Function Netzanschluss (Grid connection) Description Total operating hours of the inverter. Changing this parameter may be necessary if you replace your inverter and want to use data from the old device. Hardware version of the operation control unit (BFS). Device-internal parameter. Activation and deactivation of the islanding detection via impedance monitoring (0 = off / 1 = on). This parameter can only be changed when the inverter is deactivated (disconnection on the AC side), or if it is in "Stop" mode. SMA Grid Guard parameters can only be changed after the SMA Grid Guard password has been entered. This value defines the integral factor of the power control. It determines the factor of the time-related response to the control deviation (control deviation = nominal power actual power). ki * Time integral of control deviation = corrective power value Excessively high values lead to vibrations and instability in the system. This value defines the proportional factor of the power control. It sets the factor of the direct response to the control deviation. kp * Control deviation = corrective power value Excessively high values lead to vibrations and instability in the system. Compensation for the voltage drop in the cabling. This parameter takes into account the voltage drop between the inverter and the power supply line point. The 10-minute average voltage at the inverter connection must not exceed the sum of ACVtgRPro plus LDVtgC. The LDVtgC parameter is preset to 0 V for Germany. In grid regions where an additional voltage increase protection (see ACVtgRPro parameter) is not required, the LDVtgC parameter is preset to 50 V. The voltage increase protection is therefore deactivated for these grid regions (253 V + 50 V = 303 V) and only the fast disconnection intervenes via the Vac-Max parameter. Default Param.: Resets all country-independent parameters to the factory settings. reset op.data: resets all operating data. Reset errors: resets a permanent fault. With this operating parameter, it is possible to store information in the inverter, regarding which phase the inverter is connected to. This means that in the plant overview it is easy to manage which inverter is installed at which phase. 10 SB_SMC_WB_Par-TEN Technical Description

11 SMA Solar Technology AG Explanation of the Operating Parameters Name Operating Mode P-HzStop* P-HzStr* P-W* P-WCtlHzMod* P-WGra* P-Wind-Ramp P-WMod* Description Operating mode of the inverter: Mpp-Operation: Maximum Power Point V-Const: Constant voltage mode (the setpoint is defined in "Vconst- Setpoint") Stop: disconnection from grid, no operation Turbine: operating mode for small wind turbine systems (this operating mode may only be set in wind energy inverters). The use of this mode is expressly prohibited for inverters of other energy forms, such as Sunny Boys or Sunny Mini Centrals. Otherwise the operation permission and all warranty claims become void.) Switch-back frequency for full active power. More information on this parameter can be found in the installation guide of the respective inverter. Start frequency for active power limitation. More information on this parameter can be found in the installation guide of the respective inverter. Maximum active power of the inverter for an active power process with a firmly specified active power limitation. Activation of the characteristic curve for the active power limitation, in relation to the set frequency thresholds P(f). More information on this parameter can be found in the installation guide of the respective inverter. Gradient of the active power limitation. More information on this parameter can be found in the installation guide of the respective inverter. This parameter lets you configure the controlled startup of the small wind turbine system. Only once the inverter is connected to the grid, will the small wind turbine system not be charged rapidly, but rather with a configurable ramp. After the connection process, this parameter will no longer be active. Activation of the process for active power limitation. More information on this parameter can be found in the installation guide of the respective inverter. PF-PF* Specification of the displacement power factor cos φ. PF-PFExt* Setting of the excitation (lagging, leading). Phase* Setting the phase to which the inverter feeds. More information on this parameter can be found in the installation guide of the respective inverter. Plimit Display of the active power limitation of the inverter. Technical Description SB_SMC_WB_Par-TEN

12 Explanation of the Operating Parameters SMA Solar Technology AG Name Pmax PowerBalancer PTot-Min Q-VArMod* Ripple-Ctl-Frq Ripple-Ctl-Lev Ripple-Ctl-Rcvr Riso-Min Slimit SMA-Grid-Guard SMA-SN Smax Description Active power limitation of the inverter. Operating mode of the SMA Power Balancer for prevention of asymmetric loads in 3-phase systems with Sunny Mini Central. The SMA Power Balancer has four operating modes: Off: the SMA Power Balancer is deactivated. In the event of a device fault or grid voltage disturbance at an inverter, only this inverter is disconnected from the grid and the other two devices continue to run at an undiminished power level. PowerGuard: operating mode in which no distinction is made between a device fault and a grid voltage disturbance. The relevant device disconnects itself from the grid, while the other two inverters limit their output to 5 kva over a 10-minute average. PhaseGuard: operating mode in which a distinction is made between a device fault and a grid voltage disturbance. In the event of a device fault at the first Sunny Mini Central, the other two inverters continue to operate without reducing their output. In case of a grid voltage disturbance, all devices will immediately disconnect from the grid. FaultGuard: operating mode in which a distinction is made between a device fault and a grid voltage disturbance. In the event of a device fault, the fault message will be sent to the other two devices with a time delay of 5 minutes. After the 5 minutes have passed, the other two devices will disconnect from the grid as well. In case of a grid voltage disturbance, all devices will immediately disconnect from the grid. The DC power required before the inverter begins feeding power into the grid. Selection of the reactive power procedure. More information on this parameter can be found in the installation guide of the respective inverter. The "Ripple-Ctl-Frq", "Ripple-Ctl-Lev", and "Ripple-Ctl-Rcvr" parameters are intended for handling ripple control signals from the SMA inverters. These parameters are not available for all inverters. These parameters may only be changed after prior consultation with SMA Solar Technology AG. This parameter is used to change the threshold value for the insulation monitoring. The parameter cannot be permanently saved. Apparent power limitation of the inverter SMA Grid Guard version Serial number of inverter Apparent power limitation of the inverter 12 SB_SMC_WB_Par-TEN Technical Description

13 SMA Solar Technology AG Explanation of the Operating Parameters Name Speicher (Memory) T-Max-Fan T-Max-Fan-In T-Max-Fan-Mod T-Start-Fan T-Start-Fan-In T-Start-Fan-Mod T-Start* T-Stop T-Stop-Fan T-Stop-Fan-In T-Stop-Fan-Mod testcurrent Zac UdcWindStart UdcWindStop Uac-Min-Tm* Uac-Max-Tm* Uac-Min-Fast-Tm* Uac-Max-Fast-Tm* Vac-Min* Vac-Max* Uac-Min-Fast* Uac-Max-Fast* Vac-Tavg Description Permanent: modified parameters are stored in the EEPROM and can be used even when the inverter has been restarted. Volatil: prevents the parameters being saved in the EEPROM. The parameters are only saved until the next start. Temperature for maximum fan rotation speed. As of this temperature, the fan will start to run at minimum speed. Grid monitoring time: time during which the inverter monitors the grid before it connects to the grid. The period the inverter waits before disconnecting from the grid when Udc drops below Vpv-Start. If, after a temperature increase, the inverter cools down to below this threshold value, the fan will switch off again. Setting for the impulse for impedance monitoring (0 = off). This parameter can only be changed when the inverter is deactivated (disconnection on the AC side), or if it is in "Stop" mode. This parameter defines the starting point of the output characteristic curve. When the DC input voltage reaches this value after grid synchronization, the inverter uses the output characteristic curve to start the load of the small wind turbine system and feeds into the grid. This parameter is only relevant for the Windy Boy 1100LV. If the value falls below UDCWindStop, the inverter decreases its internal (DC) consumption by deactivating the power semiconductor. Switch-off time for voltage increase protection (Uac-Max-Tm, Uac-Max-Fast-Tm) and voltage decrease protection (Uac-Min-Tm, Uac-Min-Fast-Tm). Additional monitoring of AC voltage (deactivated for Germany). Lower (Vac-Min) and upper (Vac-Max) limits of the allowable AC voltage, before the grid monitoring system disconnects the device from the grid. Averaging time for measuring grid frequency. Technical Description SB_SMC_WB_Par-TEN

14 Explanation of the Operating Parameters SMA Solar Technology AG Name Vconst-Setpoint Vpv-Start VRef* VRefOfs* WGraReconEna* Wind_a0 Wind_a1 Wind_a2 Wind_a3 Zac-Max Description Target PV voltage for constant operational voltage. This parameter is only important when the "Operating Mode" parameter is set to "V-Const". The DC voltage required before the inverter begins feeding power into the grid. This value is above the minimum MPP voltage which is required in order to always guarantee safe connection to the grid, and to minimize grid relay wear. If, after disconnection from the grid, and in the absence of any further disturbances, the inverter does not automatically reconnect to the grid, this parameter can be decreased in small steps. It should be noted that if the value is set too low, this leads to an increased number of connections to the grid, and thus to increased wear of components. Phase voltage at the output side of the transformer. Adjustable voltage offset (e.g. through cable losses). Activation of the gradient of the active power limitation upon reactivation after a system incident. The following formula gives the factors for the voltage-dependent power calculation: P(u) = a 0 + a 1 * U + a 2 * U² + a 3 * U³ Maximum grid impedance before the grid monitoring system disconnects the device from the grid. 14 SB_SMC_WB_Par-TEN Technical Description

15 SMA Solar Technology AG Setting the Country Standard 4 Setting the Country Standard Using the "Default" parameter you can set the installation country and/or the grid connection standard valid for your country via a communication device or a PC with appropriate software. This is necessary if the inverter was originally ordered for another country and was preset accordingly by SMA Solar Technology AG. If your country or the standard valid in your country is not listed in the following overview, please contact the SMA Serviceline. Parameter Setting Description Default* GER/MSD Country-specific parameter settings for Germany in accordance with the DIN VDE 0126 (4.99) GER/VDE Country-specific parameter settings for Germany and France in accordance with the DIN VDE VDE /UTE Country-specific parameter settings for France in accordance with the UTE C SP/RD1663 Country-specific parameter settings for Spain SP/RD1663-A SP/RD1663/661 SP/RD1663/661-A AUS/AS4777 Country-specific parameter settings for Australia IT/DK5940 Ed.2 Country-specific parameter settings for Italy GB Country-specific parameter settings for Great Britain GB/G83 GB/G83/1-1 KOR/KEPCO Guide Country-specific parameter settings for Korea EN Country-specific parameter settings for various European countries EN CZ CZ/PPDS Country-specific parameter settings for the Czech Republic GR/PPC Country-specific parameter settings for Greece TH/PEA Country-specific parameter settings for Thailand (City) TH/MEA TH/IEC61727/PEA TH/IEC61727/MEA BE/C10/11 Country-specific parameter settings for Belgium CN/CGC/GF001 Country-specific parameter settings for China Technical Description SB_SMC_WB_Par-TEN

16 Setting the Country Standard SMA Solar Technology AG Parameter Setting Description Default* MVtgDirective Extension to the disconnection thresholds of the inverter for voltage and frequency to the extreme values (prerequisite: external three-phase decoupling protection) (only for SMC with Reactive Power Control, SMC 5000A, SMC 6000A, and SMC 7000HV-11) Other Parameter settings for countries for which no predefined settings exist can be configured here. trimmed If country-specific parameters have been changed, "trimmed" is shown in the display. OFF_Grid Setting for inverters which are operated in a standalone grid. More information can be found in the Sunny Island installation guide. 16 SB_SMC_WB_Par-TEN Technical Description

17 SMA Solar Technology AG Value Ranges and Factory Settings 5 Value Ranges and Factory Settings 5.1 Sunny Boy Sunny Boy 1200/1700 Name Value/Range Default Value ACVtgRPro* 230 V 300 V 253 V AntiIsland-Ampl* 0deg 10deg Depending on country standard AntiIsland-Freq* 1 mhz mhz 500 mhz dfac-max* 0.1 Hz/s 4.0 Hz/s 4.0 Hz/s E_total 0 kwh kwh 0kWh Fac-delta * 0.1 Hz 4.5 Hz Depending on country standard Fac-delta+* 0.1 Hz 4.5 Hz Depending on country standard GndFltRea* (firmware version GndFltWrn Depending on country standard 3.06 and higher) GndFltDscon h_total 0 h h 0h LDVtgC* 0 V 50 V Depending on country standard Operating Mode Mpp-Operation Mpp-Operation V-Const Stop Pmax* (SB 1200) 0 W W Pmax* (SB 1700) 0 W W T-Start* 5 s s Depending on country standard T-Stop 1 s s 2 s Vac-Max* 230 V 300 V Depending on country standard Vac-Min* 160 V 300 V Depending on country standard Vconst-Setpoint 150 V 430 V 410 V Vpv-Start (SB 1200) 110 V 400 V 120 V Vpv-Start (SB 1700) 150 V 400 V 180 V Technical Description SB_SMC_WB_Par-TEN

18 Value Ranges and Factory Settings SMA Solar Technology AG Sunny Boy 2100TL Name Value/Range Default Value dfac-max* Hz/s 4.0 Hz/s 4.0 Hz/s dv V-Const 0.5 V/s 20 V/s 2V/s dv-mpp Track 0.55 V/TaMpp 1.4 V/TaMpp 10 V/TaMpp dvref-mpp 5 V 380 V 100 V dzac-max* 0 m Ω m Ω Depending on country standard E_total 0 kwh kwh 0kWh Fac-delta * 0Hz 4.5Hz Depending on country standard Fac-delta+* 0Hz 4.5Hz Depending on country standard h_total 0 h h 0h I SearchNewMPP 0mA 9000mA 164 ma Operating Mode Mpp-Operation Mpp-Operation V-Const Stop Riso-Min 0 k Ω k Ω k Ω T-Start* 5 s 300 s 10 s T-Stop 1 s 300 s 10 s Vac-Max* 180 V 300 V Depending on country standard Vac-Min* 180 V 300 V Depending on country standard Vconst-Setpoint 125 V 600 V 600 V Vpv-Start 125 V 600 V 150 V 18 SB_SMC_WB_Par-TEN Technical Description

19 SMA Solar Technology AG Value Ranges and Factory Settings Sunny Boy 2500/3000 Name Value/Range Default Value ACVtgRPro* 230 V 300 V 253 V AntiIsland-Ampl* 0 deg 10 deg Depending on country standard AntiIsland-Freq* 0 mhz mhz 500 mhz dfac-max* 0.1 Hz/s 4.0 Hz/s 4.0 Hz/s E_total 0 kwh kwh 0kWh Fac-delta * 0.1 Hz 4.5 Hz Depending on country standard Fac-delta+* 0.1 Hz 4.5 Hz Depending on country standard h_total 0 h h 0h LDVtgC* 0 V 50 V Depending on country standard Operating Mode Mpp-Operation Mpp-Operation V-Const Stop Pmax (SB 2500) 0 W W W Pmax (SB 3000) 0 W W W T-Start* 5 s s Depending on country standard T-Stop 1 s s 2 s Vac-Max* 230 V 300 V Depending on country standard Vac-Min* 160 V 230 V Depending on country standard Vconst-Setpoint 250 V 600 V 600 V Vpv-Start (SB 2500) 250 V 600 V 300 V Vpv-Start (SB 3000) 290 V 600 V 330 V Technical Description SB_SMC_WB_Par-TEN

20 Value Ranges and Factory Settings SMA Solar Technology AG Sunny Boy 3300/3800 Name Value/Range Default Value ACVtgRPro* 230 V 300 V 253 V AntiIsland-Ampl* 0 deg 10 deg 0 deg AntiIsland-Freq* 0 mhz mhz 500 mhz dfac-max* 0.1 Hz/s 4.0 Hz/s 4.0 Hz/s dzac-max 350 m Ω m Ω 700 m Ω E_total 0 kwh kwh 0kWh Fac-delta * 0.1 Hz 4.5 Hz Depending on country standard Fac-delta+* 0.1 Hz 4.5 Hz Depending on country standard GndFltRea GndFltWrn GndFltWrn GndFltDscon h_total 0 h h 0h LDVtgC* 0 V 50 V Depending on country standard Operating Mode Mpp-Operation Mpp-Operation V-Const Stop Pmax (SB 3300) W W Pmax (SB 3800) W W Ripple-Ctl-Frq 105 Hz Hz Hz Ripple-Ctl-Lev 0.5 % 8.00 % 1.70 % Ripple-Ctl-Rcvr enable auto disable auto Riso-Min 0 k Ω k Ω k Ω T-Start* 5 s s Depending on country standard T-Stop 1 s s 2 s testcurrent Zac 0 ma ma ma Vac-Max* 230 V 300 V Depending on country standard Vac-Min* 160 V 230 V Depending on country standard Vconst-Setpoint 200 V 500 V 500 V Vpv-Start 200 V 500 V 250 V 20 SB_SMC_WB_Par-TEN Technical Description

21 SMA Solar Technology AG Value Ranges and Factory Settings Sunny Boy 3300TL HC Name Value/Range Default Value ACVtgRPro* 230 V 300 V 253 V AntiIsland-Ampl* 0 deg 10 deg 0 deg AntiIsland-Freq* 0 mhz mhz 500 mhz dfac-max* 0.1 Hz/s 4.0 Hz/s 4.0 Hz/s dzac-max* 350 m Ω m Ω Depending on country standard E_total 0 kwh kwh 0kWh Fac-delta * 0.1 Hz 4.5 Hz 2.45 HZ Fac-delta+* 0.1 Hz 4.5 Hz 0.19 HZ h_total 0 h h 0h LDVtgC* 0 V 50 V Depending on country standard Operating Mode Mpp-Operation Mpp-Operation V-Const Stop Ripple-Ctl-Frq 105 Hz Hz Hz Ripple-Ctl-Lev 0.5 % 8.00 % 8.00 % Ripple-Ctl-Rcvr enable disable disable auto PTot-Min 0 W 500 W 35 W Riso-Min k Ω k Ω k Ω T-Start* 2 s 300 s 2s testcurrent Zac 0mA/1mA 1mA Vac-Max* 230 V 300 V 260 V Vac-Min* 160 V 300 V 198 V Vconst-Setpoint 0 V 750 V 290 V Technical Description SB_SMC_WB_Par-TEN

22 Value Ranges and Factory Settings SMA Solar Technology AG 5.2 Sunny Mini Central Sunny Mini Central 4600A/5000A/6000A Name Value/Range Default Value ACVtgRPro* 230 V 300 V 253 V AntiIsland-Ampl* 0 deg 10 deg 0 deg AntiIsland-Freq* 0.1 mhz mhz 500 mhz dfac-max* 0.1 Hz/s 6.0 Hz/s Depending on country standard dzac-max (SMC 4600A) 0.35 m Ω m Ω 685 m Ω dzac-max (SMC 5000A) 0.35 m Ω m Ω 685 m Ω dzac-max (SMC 6000A) 0.35 m Ω m Ω 670 m Ω E_total 0 kwh kwh 0kWh Fac-delta * 0.1Hz 6Hz Depending on country standard Fac-delta+* 0.1Hz 5Hz Depending on country standard Fac-Limit delta 0Hz 5Hz 2HZ Fac-Start delta 0Hz 5Hz 1HZ Fan-Test GndFltRea GndFltWrn GndFltWrn GndFltDscon h_total 0 h h 0h LDVtgC* 0 V 50 V Depending on country standard Operating Mode Mpp-Operation Mpp-Operation V-Const Stop P-HzStop* 0Hz 5Hz 0.05 HZ P-HzStr* 0Hz 5Hz 0.20 HZ P-WCtlHzMod* Off Off On P-WGra* 10 %/Hz 100 %/Hz 40 %/Hz Pmax* (SMC 4600A) 0 W W W Pmax* (SMC 5000A) 0 W W W Pmax* (SMC 6000A) 0 W W W PowerBalancer Off Off PowerGuard PhaseGuard FaultGuard Ripple-Ctl-Frq 105 Hz Hz Hz 22 SB_SMC_WB_Par-TEN Technical Description

23 SMA Solar Technology AG Value Ranges and Factory Settings Name Value/Range Default Value Ripple-Ctl-Lev 0.5 % 8.0 % 8.0 % Ripple-Ctl-Rcvr enable disable disable auto Riso-Min 0 k Ω k Ω k Ω T-Max-Fan 0 C 100 C 90 C T-Start-Fan 0 C 100 C 70 C T-Start* 5 s s Depending on country standard T-Stop 1 s s 2 s T-Stop-Fan 0 C 100 C 50 C testcurrent Zac 0 ma ma ma Vac-Max* 230 V 300 V Depending on country standard Vac-Min* 70 V 230 V Depending on country standard Vconst-Setpoint 250 V 600 V 600 V Vpv-Start 250 V 600 V 300 V Technical Description SB_SMC_WB_Par-TEN

24 Value Ranges and Factory Settings SMA Solar Technology AG Sunny Mini Central 7000HV/7000HV-11 Name Value/Range Default Value ACVtgRPro* 230 V 300 V 253 V AntiIsland-Ampl* 0 deg 10 deg Depending on country standard AntiIsland-Freq* 0.1 mhz mhz 500 mhz dfac-max 0.1 Hz/s 4.0 Hz/s 4.0 Hz/s DGS-HystVolNom* 0 % 60 % 5% (SMC 7000HV-11) DGS-PWMVolNom* 40 % 100 % 70 % (SMC 7000HV-11) dzac-max (SMC 7000HV) 0.35 m Ω m Ω 650 m Ω E_total 0 kwh kwh 0kWh Fac-delta * 0.1Hz 6Hz Depending on country standard Fac-delta+* 0.1Hz 5Hz Depending on country standard Fac-Limit delta 0Hz 5Hz 2HZ Fac-Start delta 0Hz 5Hz 1HZ Fan-Test GndFltRea (SMC 7000HV-11) GndFltWrn GndFltWrn GndFltDscon h_total 0 h h 0h LDVtgC* 0 V 50 V 0V Operating Mode Mpp-Operation Mpp-Operation V-Const Stop P-HzStop* 0Hz 5Hz 0.05 HZ P-HzStr* 0Hz 5Hz 0.20 HZ P-W* (SMC 7000HV-11) 0 W W W P-WCtlHzMod* Off Off (SMC 7000HV-11) On P-WGra* (SMC 7000HV-11) 10 %/Hz 100 %/Hz 40 %/Hz P-WMod* (SMC 7000HV-11) Off WCtlCom WCnst WCtlCom PF-PF* (SMC 7000HV-11) PF-PFExt* (SMC 7000HV-11) Overexcited Underexcited Underexcited Pmax 0 W W W 24 SB_SMC_WB_Par-TEN Technical Description

25 SMA Solar Technology AG Value Ranges and Factory Settings Name Value/Range Default Value PowerBalancer Off Off PowerGuard PhaseGuard FaultGuard Q-VArMod* Off PFCnst (SMC 7000HV-11) PFCnst PFCtlCom Ripple-Ctl-Frq 105 Hz Hz Hz Ripple-Ctl-Lev 0.5 % 8.0 % 8.0 % Ripple-Ctl-Rcvr enable disable disable auto Riso-Min 0 k Ω k Ω k Ω Smax (SMC 7000HV-11) 0 VA VA VA T-Max-Fan 0 C 100 C 90 C T-Start-Fan 0 C 100 C 70 C T-Start* 5 s s Depending on country standard T-Stop 1 s s 2 s T-Stop-Fan 0 C 100 C 50 C testcurrent Zac 0 ma ma ma Vac-Max* 230 V 300 V Depending on country standard Vac-Min* 70 V 230 V Depending on country standard Vconst-Setpoint 335 V 800 V 800 V Vpv-Start 370 V 800 V 400 V VRef* (SMC 7000HV-11) 215 V 245 V 230 V VRefOfs* (SMC 7000HV-11) 20 V 20 V 0V WGraReconEna* (SMC 7000HV-11) Technical Description SB_SMC_WB_Par-TEN

26 Value Ranges and Factory Settings SMA Solar Technology AG Sunny Mini Central 6000TL/7000TL/8000TL Name Value/Range Default Value ACVtgRPro* 230 V 300 V 253 V AID-Esk-Alpha* 0 deg/% 40 deg/% Depending on country standard AntiIsland-Ampl* 0 deg 10 deg Depending on country standard AntiIsland-Freq* 0.1 mhz mhz Depending on country standard DC-Offset_Max* 100 ma ma Depending on country standard dfac-max* 0.1 Hz/s 6.0 Hz/s Depending on country standard E_total 0 kwh kwh 0kWh Fac-delta * 0.1 Hz 6.0 Hz Depending on country standard Fac-delta+* 0.1 Hz 5.0 Hz Depending on country standard Fac-Limit delta 0Hz 5Hz 2HZ Fac-Start delta 0Hz 5Hz 1HZ Fan-Test h_total 0 h h 0h LDVtgC* 0 V 50 V Depending on country standard Operating Mode Mpp-Operation Mpp-Operation V-Const Stop Pmax* (SMC 6000TL) 0 W W W Pmax* (SMC 7000TL) 0 W W W Pmax* (SMC 8000TL) 0 W W W PowerBalancer Off Off PowerGuard PhaseGuard FaultGuard Riso-Min k Ω k Ω k Ω T-Max-Fan 0 C 110 C 90 C T-Start-Fan 0 C 110 C 70 C T-Start* 5 s s Depending on country standard T-Stop 1 s s 2 s T-Stop-Fan 0 C 110 C 50 C Uac-Max-Fast* 230 V 300 V Depending on country standard Uac-Min-Fast* 115 V 220 V Depending on country standard Vac-Max* 230 V 300 V Depending on country standard Vac-Min* 160 V 300 V Depending on country standard Vconst-Setpoint 250 V 700 V 600 V 26 SB_SMC_WB_Par-TEN Technical Description

27 SMA Solar Technology AG Value Ranges and Factory Settings Name Value/Range Default Value Vpv-Start 335 V 700 V 400 V Technical Description SB_SMC_WB_Par-TEN

28 Value Ranges and Factory Settings SMA Solar Technology AG Sunny Mini Central 9000TL/10000TL/11000TL Name Value/Range Default Value ACVtgRPro* 230 V 300 V 253 V AID-Esk-Alpha* 0 deg/% 40 deg/% Depending on country standard AntiIsland-Ampl* 0 deg 10 deg Depending on country standard AntiIsland-Freq* 0.1 mhz mhz 500 mhz AntiIsland-Lim* 0.1 Hz 6.0 Hz Depending on country standard DC-Offset_Max* 100 ma ma 800 ma dfac-max* 0.1 Hz/s 6.0 Hz/s Depending on country standard E_total 0 kwh kwh 0kWh Fac-delta * 0.1 Hz 6.0 Hz Depending on country standard Fac-delta+* 0.1 Hz 5.0 Hz Depending on country standard Fac-Limit delta 0Hz 5Hz 2HZ Fac-Start delta 0Hz 5Hz 1HZ Fan-Test h_total 0 h h 0h LDVtgC* 0 V 50 V Depending on country standard Operating Mode Mpp-Operation Mpp-Operation V-Const Stop Pmax* (SMC 9000TL-10) 0 W W W Pmax* (SMC 10000TL-10) 0 W W W Pmax* (SMC 11000TL-10) 0 W W W PowerBalancer Off Off PowerGuard PhaseGuard FaultGuard Riso-Min 280 k Ω k Ω 280 k Ω T-Max-Fan-In 0 C 80 C 75 C T-Max-Fan-Mod 0 C 120 C 110 C T-Start-Fan-In 0 C 80 C 65 C T-Start-Fan-Mod 0 C 120 C 80 C T-Start* 5 s s Depending on country standard T-Stop 1 s s 2 s T-Stop-Fan-In 0 C 80 C 60 C T-Stop-Fan-Mod 0 C 120 C 70 C Uac-Max-Fast* 220 V 300 V 300 V 28 SB_SMC_WB_Par-TEN Technical Description

29 SMA Solar Technology AG Value Ranges and Factory Settings Name Value/Range Default Value Uac-Min-Fast* 115 V 220 V 120 V Vac-Max* 230 V 300 V Depending on country standard Vac-Min* 160 V 230 V Depending on country standard Vconst-Setpoint 250 V 700 V 500 V Vpv-Start 335 V 700 V 400 V Technical Description SB_SMC_WB_Par-TEN

30 Value Ranges and Factory Settings SMA Solar Technology AG Sunny Mini Central 9000TL/10000TL/11000TL with Reactive Power Control Name Value/Range Default Value ACVtgRPro* 230 V 300 V 253 V AID-Esk-Alpha* 0 deg/% 40 deg/% Depending on country standard DC-Offset_Max* 100 ma ma Depending on country standard DGS-PWMVolNom* 40 % 100 % 70 % DGS-HystVolNom* 0 % 60 % 5% E_total 0 kwh kwh 0kWh Fac-delta * 0.1Hz 6Hz Depending on country standard Fac-delta+* 0.1Hz 5Hz Depending on country standard Fac-Limit delta 0Hz 5Hz 2HZ Fac-Start delta 0Hz 5Hz 1HZ Fan-Test h_total 0 h h 0h LDVtgC* 0 V 50 V Depending on country standard Operating Mode Mpp-Operation Mpp-Operation V-Const Stop P-HzStop* 0Hz 5Hz 0.05 HZ P-HzStr* 0Hz 5Hz 0.20 HZ P-W* 0 W W W P-WCtlHzMod* Off Off On P-WGra* 10 %/Hz 100 %/Hz 40 %/Hz P-WMod* Off WCtlCom WCnst WCtlCom PF-PF* PF-PFExt* Overexcited Underexcited Underexcited Pmax (SMC 9000TLRP-10) 0 W W W Pmax (SMC 10000TLRP-10) 0 W W W Pmax (SMC 11000TLRP-10) 0 W W W 30 SB_SMC_WB_Par-TEN Technical Description

31 SMA Solar Technology AG Value Ranges and Factory Settings Name Value/Range Default Value PowerBalancer Off Off PowerGuard PhaseGuard FaultGuard Q-VArMod* Off PFCnst PFCnst PFCtlCom Riso-Min 900 k Ω k Ω 900 k Ω Smax (SMC 10000TLRP-10) 0 VA VA VA Smax (SMC 11000TLRP-10) 0 VA VA VA Smax (SMC 9000TLRP-10) 0 VA VA VA T-Start* 5 s s Depending on country standard T-Stop 1 s s 2 s Uac-Max-Fast* 230 V 300 V Depending on country standard Uac-Min-Fast* 70 V 220 V Depending on country standard Vac-Max* 230 V 300 V Depending on country standard Vac-Min* 70 V 230 V Depending on country standard Vconst-Setpoint 250 V 700 V 500 V Vpv-Start 335 V 700 V 400 V VRef* 215 V 245 V 230 V VRefOfs* 20 V 20 V 0V WGraReconEna* Technical Description SB_SMC_WB_Par-TEN

32 Value Ranges and Factory Settings SMA Solar Technology AG 5.3 Windy Boy Windy Boy 1100LV Name Value/Range Default Value KI-Wind-Reg KP-Wind-Reg Operating Mode Mpp-Operation Turbine V-Const Stop Turbine P-Wind-Ramp 10 W/s 600 W/s 400 W/s Pmax 0 W W W T-Stop 1 s s 2 s UdcWindStart 1 V 60 V 25 V UdcWindStop 1 V 60 V 24.9 V Vpv-Start 20 V 60 V 25 V Wind_a Wind_a Wind_a Wind_a SB_SMC_WB_Par-TEN Technical Description

33 SMA Solar Technology AG Value Ranges and Factory Settings Windy Boy 1200/1700 Name Value/Range Default Value KI-Wind-Reg 0 V 0.25 V KP-Wind-Reg 0 V 0.25 V Operating Mode Mpp-Operation Turbine V-Const Stop Turbine P-Wind-Ramp 10 W/s W/s 330 W/s Pmax (WB 1200) 0 W W W Pmax (WB 1700) 0 W W W T-Stop 1 s s 2 s UdcWindStart 1 V 500 V 150 V Vpv-Start (WB 1200) 110 V 400 V 120 V Vpv-Start (WB 1700) 150 V 400 V 180 V Wind_a0 (WB 1200) 83 Wind_a0 (WB 1700) 341 Wind_a1 (WB 1200) 2.92 Wind_a1 (WB 1700) 8.76 Wind_a2 (WB 1200) Wind_a2 (WB 1700) 73 Wind_a3 (WB 1200) Wind_a3 (WB 1700) Technical Description SB_SMC_WB_Par-TEN

34 Value Ranges and Factory Settings SMA Solar Technology AG Windy Boy 2500/3000 Name Value/Range Default Value KI-Wind-Reg KP-Wind-Reg Operating Mode Mpp-Operation Turbine V-Const Stop Turbine P-Wind-Ramp 10 W/s W/s 500 W/s Pmax (WB 2500) 0 W W W Pmax (WB 3000) 0 W W W T-Stop 1 s s 2 s UdcWindStart (WB 2500) 150 V 600 V 250 V UdcWindStart (WB 3000) 150 V 600 V 270 V Vpv-Start (WB 2500) 250 V 600 V 300 V Vpv-Start (WB 3000) 290 V 600 V 330 V Wind_a0 (WB 2500) 1538 Wind_a0 (WB 3000) 3923 Wind_a1 (WB 2500) Wind_a1 (WB 3000) Wind_a2 (WB 2500) Wind_a2 (WB 3000) 128 Wind_a3 (WB 2500) Wind_a3 (WB 3000) SB_SMC_WB_Par-TEN Technical Description

35 SMA Solar Technology AG Value Ranges and Factory Settings Windy Boy 3300/3800 Name Value/Range Default Value Operating Mode Mpp-Operation Turbine V-Const Stop Turbine GndFltRea GndFltWrn GndFltWrn GndFltDscon KI-Wind-Reg KP-Wind-Reg P-Wind-Ramp (WB 3300) 10 W/s W/s 600 W/s P-Wind-Ramp (WB 3800) 10 W/s W/s 650 W/s Pmax (WB 3300) 0 W W W Pmax (WB 3800) 0 W W W T-Stop 1 s s 2 s Vpv-Start 200 V 500 V 250 V UdcWindStart (WB 3300) 150 V 500 V 200 V UdcWindStart (WB 3800) 150 V 500 V 180 V Wind_a0 (WB 3300) 290 Wind_a0 (WB 3800) Wind_a1 (WB 3300) Wind_a1 (WB 3800) 0.83 Wind_a2 (WB 3300) 52 Wind_a2 (WB 3800) 9.51 Wind_a3 (WB 3300) 120 Wind_a3 (WB 3800) Technical Description SB_SMC_WB_Par-TEN

36 Value Ranges and Factory Settings SMA Solar Technology AG Windy Boy 5000A/6000A Name Value/Range Default Value GndFltRea GndFltWrn GndFltWrn GndFltDscon KI-Wind-Reg KP-Wind-Reg Operating Mode Mpp-Operation Turbine V-Const Stop Turbine P-Wind-Ramp (WB 5000A) 10 W/s W/s 830 W/s P-Wind-Ramp (WB 6000A) 10 W/s W/s W/s Pmax (WB 5000A) 0 W W W Pmax (WB 6000A) 0 W W W T-Stop 1 s s 2 s UdcWindStart (WB 5000A) 1 V 500 V 150 V UdcWindStart (WB 6000A) 1 V 800 V 150 V Vpv-Start 250 V 600 V 300 V Wind_a0 (WB 5000A) 1993 Wind_a0 (WB 6000A) 8197 Wind_a1 (WB 5000A) Wind_a1 (WB 6000A) Wind_a2 (WB 5000A) 92.3 Wind_a2 (WB 6000A) Wind_a3 (WB 5000A) Wind_a3 (WB 6000A) SB_SMC_WB_Par-TEN Technical Description

37 SMA Solar Technology AG Contact 6 Contact If you have technical problems concerning our products, contact the SMA Serviceline. We need the following information in order to provide you with the necessary assistance: Inverter type Serial number of inverter Type and number of connected PV modules or small wind turbine systems Blink code or display message of the inverter Optional equipment, e.g. communication devices SMA Solar Technology AG Sonnenallee Niestetal, Germany SMA Serviceline Inverters: Communication: Fax: Serviceline@SMA.de Technical Description SB_SMC_WB_Par-TEN

38

39 SMA Solar Technology AG Legal Restrictions The information contained in this document is the property of SMA Solar Technology AG. Publishing its content, either partially or in full, requires the written permission of SMA Solar Technology AG. Any internal company copying of the document for the purposes of evaluating the product or its correct implementation is allowed and does not require permission. Exclusion of liability The general terms and conditions of delivery of SMA Solar Technology AG shall apply. The content of these documents is continually checked and amended, where necessary. However, discrepancies cannot be excluded. No guarantee is made for the completeness of these documents. The latest version is available online at or from the usual sales channels. Guarantee or liability claims for damages of any kind are excluded if they are caused by one or more of the following: Damages during transportation Improper or inappropriate use of the product Operating the product in an unintended environment Operating the product whilst ignoring relevant, statutory safety regulations in the deployment location Ignoring safety warnings and instructions contained in all documents relevant to the product Operating the product under incorrect safety or protection conditions Altering the product or supplied software without authority The product malfunctions due to operating attached or neighboring devices beyond statutory limit values In case of unforeseen calamity or force majeure The use of supplied software produced by SMA Solar Technology AG is subject to the following conditions: SMA Solar Technology AG rejects any liability for direct or indirect damages arising from the use of software developed by SMA Solar Technology AG. This also applies to the provision or non-provision of support activities. Supplied software not developed by SMA Solar Technology AG is subject to the respective licensing and liability agreements of the manufacturer. SMA Factory Warranty The current guarantee conditions come enclosed with your device. These are also available online at and can be downloaded or are available on paper from the usual sales channels if required. Trademarks All trademarks are recognized even if these are not marked separately. Missing designations do not mean that a product or brand is not a registered trademark. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by SMA Solar Technology AG is under license. SMA Solar Technology AG Sonnenallee Niestetal Germany Tel Fax info@sma.de 2004 to 2010 SMA Solar Technology AG. All rights reserved Technical Description SB_SMC_WB_Par-TEN

40