ScaffMover Datasheet. Wire Connection Diagram. 1. Electronics Parts Connection Diagram. ScaffMover. Motor Control Board. 10 Ah/ 14.

Transcription

1 ScaffMover Datasheet 1. Electronics Parts Connection Diagram Wire Connection Diagram ScaffMover Motor 1 GND Motor Motor Control Board BATT 10 Ah/ 14.8V battery 1 Relay Charging Positive; 2- Discharging positive 3 Charging Negative; 4 Discharging Negative 3 Receiver Board Data Cable Back Cover (with Charge Plug)

2 Battery Assembly: Battery can slid on to chassis and connect to male plug on the chassis We will design Cover to Cover this male plug & Wires 2. Technical Data Battery voltage Battery type Battery capacity Battery operating capacity 14.8V (changed from 14,4V) Lithium Approx mah (Changed from mAh) Approx. 1 hr. continuously operation, Battery charger Normal V, 5 A (Changed from 8 A) Remote control battery Max. load stress Speed unloaded 2 x AA 1.5 Volt 200kg Rapid speed: Approx. 16 m/min. and normal Speed: 9m/min (according to calculation, correct speed has to be measured during the test) Speed loaded Rapid Speed Approx. 12 m/min. and normal speed: 7m/min (according to calculation, correct speed has to be measured during the test) Motor Safety function Hauling capacity tracks Weight 2 x DC motors 6 hrs Auto shut-off Max 450 kg 2 pcs. with Non-marking Belt Approx. 15 kg (Changed from 20 Kg, due to bracket)

3 3. Operation: Pairing the Camper Trolley 1. Turn on the Remote Control by pushing the Forward button ( ) once. The green light on the Remote Control will turn on. 2. Turn on the Camper Trolley by clicking the Start/Stop button. The green light on the Camper Trolley will turn on. Now simultaneously press and hold the Turn Right button ( ) on the Remote Control and press and hold the Start/Stop button on the Camper Trolley, both LED lights start to blink for 8 seconds, after which the LED lights will light constantly. Now the Camper Trolley and Remote Control have been re-paired and are ready to use. If this pairing procedure is unsuccessful, the Remote Control will turn off automatically in around 15 seconds, and the user needs to redo the procedure from step 1. The Camper Trolley logo on the remote control must always point toward the trolley. Use both hands on the remote control, and hold it horizontally during use. - Forward: To move forward, in the same direction as the antenna, hold down forward button ( ); - Forward Fast: To move forward, in the same direction as the antenna, hold down forward button ( ) and hold down Rapid button. - Backward: To move backward/reverse, hold down the back button ( ). - Backward Fast: To move forward, in the same direction as the antenna, hold down forward button ( ) and hold down Rapid button. - Turn: To turn, hold down the forward ( ) or backward ( ) button while at the same time holding down one of the turn buttons of the remote control to turn right ( ) or left ( ). The Camper Trolley will only turn if you first hold the forward or backward button, followed by a turn button. - Stop: To stop the Camper Trolley from moving, simply release the forward or backward button. 4. Chassis ( refers to CT1500, but no Anodizing): BOM: 1* Main Profile, 2*Part for side profile, 2*Side profile. Material: Aluminium 6060-T6: Process: Extrusion Machining( incl. Cutting, Threading, milling, drilling deburring) Surface Treatment( None ) 5. Driving system(refer to Motor Specification and Assembly drawing): 2* DC motors, 2* Cog wheel, 2 Chain, 2* Chain wheel, 8* Transit- Wheel( 4wheels attachs to.chain wheel. ), 2*main Axle. Motor: ONLY MOTOR RATED VOLTAGE : 12 VDC OUT POWER : 100 W NO-LOAD SPEED : 2300 r/min±10% RATED SPEED : 1850 r/min±10% RATED TORQUE : 0.23 N. m RATED CURRENT : 6 A GEAR BOX ROTIO : 56/1 NO-LOAD SPEED : 41 r/min±10% RATED SPEED : 32.9 r/min±10% RATED TORQUE : 10 N. m 6. Track system( Refers to Belt drawings, assembly drawings):

4 2* Non-marking Rubber belt (pattern Inner: 66 rows, none inner tooth / Outer: 33 rows/132 pcs tooth with chamfered)., 4* SS304 Outer Belt Guide, 4*SS304 Inner Belt Guide. Friction is higher than Normal CT1500 belt. ( Hardness: 59HA. ( Normal CT1500 belt hardness is 69HA) Optional we can increase the Hardness of the rubbermix, if needed 7. Power (refers to Battery Specification): 14.48/ 10Ah Lithium battery( integrated BMS), 1* Plastic battery Cover, 1* Charger Battery A. Capacity: 10,000 mah. B. Nominal voltage: 14,8 V C. Size: 125L*200W*56H mm. D. Battery Cell: Lithium E F Cover: black plastic cover DC Connector: 4pins Female Socket; Charge station A. Charger Voltage input: AC V. B. Charging voltage Output: DC 16,8 V. C. Charging current Output : 5 Amp. D LED indicator: Red- Charging. Green-Fully Charged. E Charging time: 2 hrs. F Cover: Plastic Cover 8. Remote control A. Signal: Zigbee 2,4 GHz. B. RC battery indicator: 1 pc. LED light > 12.7 V. All LED lights > 16 V.

5 C. Four Directional buttons and one boost button. Press and hold on forward/ backward button, then press and hold on the Rapid button, the Mover will run at higher speed. The rapid button is only active in forward and reverse mode. D. Battery: 2 pcs. AA 1.5 Volt. E. Remote Control hanger: F. Remote Control protection Cover: Silicon Cover to protect the remote control. 6. Package: Plastic Inner Box (Outer)Black Carton Box for CT1500_AUS (Outer)White 7. Labels: Base on Current CT1500 label material, changed layout as follows, Forward direction