Technical specification. POW24V20A-D1 Charger. LFP/LTO + BMS connector

Transcription

1 Technical specification POW24V20A-D1 Charger LFP/LTO + BMS connector

2 LFP/LTO + BMS CNECTOR 1. Input characteristics 1-1 Rated input voltage 230V Vac 1-2 Input voltage range 180V 264V Vac 1-3 AC input voltage frequency Hz 1-4 Inrush current < 50 A 264Vac start-up in cold condition 1-5 Max input current 6 A A 2. Adjustable charging characteristics: Profile Jumper setting K1 status K2 status Remark Profile 1: LiFePO4 /LiFeYPO V This profile is determined for LiFePO4 cells 8 cells connected in series with final voltage 3.65V per cell. Profile 2: Lithium Titanate (LTO) 10 cells 26.5V This profile is determined for Lithium Titanate cells - 10 cells connection in series 2.65V per cell. Profile 3: Lithium Titanate (LTO) 12 cells 30.4V This profile is determined for Lithium Titanate cells - 12 cells connection in series 2.53V per cell. Disable mode This position cannot be used for charging. Setting this mode will result in LED red flash after AC power connected.

3 LFP/LTO + BMS CNECTOR 3. Output characteristics 2-1 Nominal charge voltage 24V Vdc 8 LiFePO4 3.00V 2 LiFePO V 10 LTO 2.40V 2-2 Fast charge voltage (V-max) LiFePO4 mode 29.2V Vdc Tolerance to stop charging according to the battery capacity ± 0.5 V, see table 2. for how to set this mode. 2-3 Fast charge voltage (V-max) LTO mode 26.5V Vdc Tolerance to stop charging according to the battery capacity ± 0.5 V, see table 2. for how to set this mode. 2-4 Fast charge voltage (V-max) Optional mode 30.4V Vdc Tolerance to stop charging according to the battery capacity ± 0.5 V, see table 2. for how to set this mode. Caution this mode will result in overcharging LiFePO4 or LTO cells! 2-5 Constant current (I-CC) 20A A Maximal current during full charge 2-6 Deep voltage level (V-deep) 21V (± 1 V) Vac Deep discharge voltage level, bellow this voltage, the current is limited to I-min 2-6 Deep discharge current (I-min) 2A A The limited current bellow V-Deep (± 0.5 A) 2-7 opt BMS limit current (I-BMS) approx 2A (± 0.5 A) A The limited current for cell balancing (controlled by BMS) 2-8 Power efficiency 230Vac

4 LFP/LTO + BMS CNECTOR 4. Protection characteristics 3-1 Thermal cutback The internal monitor reduces the charger output power in extreme operational to prevent damage 3-2 Output current limiting protection 20 A CC Mode 3-3 Output short circuit protection Short circuit protection at the output terminals. Automatic recovery after restoring to normal conditions. 3-4 Electronic reverse battery protection The charger is electronically protected against permanent reversed battery connection. 5. LED No. Profile number Technical specification Remark 4-1 Profile 1: red flash, green flash, then LED green on After AC connected 4-2 Profile 2: green flash, green flash, then Led green on After AC connected 4-3 Profile 3: green flash, then LED green on After AC connected 4-4 Charging finished Green LED After charging is finished 6. Environmental test requirements High ambient operating Low ambient operating +40 C deg C continuous operation -10 C deg C continuous operation 6-3 Highest storage +70 C deg C 6-4 Lowest storage -40 C deg C allow 2 hours to recover to normal allow 2 hours to recover to normal 6-5 Drop shock 40 g peak EN :1993

5 LFP/LTO + BMS CNECTOR 7. Charging curve (current A red, voltage V - blue) Voltage M 28,9 28,8 28,7 28,6 28,5 28,4 28,3 28,2 28, ,9 27,8 27,7 27,6 27,5 27,4 27,3 27,2 27, ,9 26,8 26,7 26,6 26,5 26,4 26,3 26,2 26,1 I Date: I Time: 20:49: m 40s 33m 20s 50m 00s 1h 06m 40s 1h 23m 20s 1h 40m 00s 1h 56m 40s 2h 13m 20s 2h 30m 00s 2h 46m 40s Current (A) 8. BMS connector operation (OPTIAL, only for the model with BMS option) Contacts Status Comment / HIGH/LOW GND Brown connected to GND Blue connected to GND Common GND Connecting both Brown (/) and Blue (HIGH/LOW current) to gnd will result in charging. Therefore it is possible to stop LOW charging by using / feature of the charger output + wire Charger with BMS support output - wire HIGH/LOW / charging GND - common gnd

6 GWL Power Ltd. Průmyslová 11, Prague 10 Czech Republic, European Union