FHSCP-UNV-10P-L-SD SPECIFICATIONS

Transcription

1 SPECIFICATIONS Emergency LED Driver Universal Voltage: VAC, 50/60Hz Output Wattage: 1-10W Output Current: 620mA Max. Long Case and Terminal Output voltage range of 16-55VDC This Driver Will Operate The Following LED Modules: Any LED module designed to accept input voltage range of 16-55VDC and can operate up to current of 620mA. General Specifications Input Voltage Input Current Input Power Standby Input Power Driver Type Output Current Output Voltage Range Output Power Number of Output Channels RFI/EMI Output Type Battery Type Battery Capacity Available Battery Recharge Time Battery Discharge Time Ambient Operating Temperature Range Sound Rating Input Surge Protection Protections Service Life Approvals / Class VAC, 50/60Hz 0.06A Max. 6W <0.5W Constant Power 620mA Max VDC 1-10W 3000mA Battery, 1800mA Battery, 1500mA Battery) 1 Channel FCC Part 15A Non-Consumer Class 2 9.6VDC 3000mAh, 1800mAh, 1500mAh 12 Hours (Refer To Battery chart) 90 Minutes Min. 10 C to 55 C (50 F to 131 F) A Line-Neutral 2kV, Line & Neutral-Ground 2kV Over / Under Voltage Protection Output Open Circuit Protection Overload Protection 50,000 hours RoHS,, CEC Title 20 Mechanical Data Tolerance=±0.02" Page1of8

2 GENERAL INSTALLATION GUIDELINES FOR LED EMERGENCY DRIVER IMPORTANT SAFE PRACTICES When using electrical equipment and this lighting device basic safety precaution should be followed at all times including but not limited to the following: PLEASE READ CAREFULLY AND FOLLOW ALL INSTRUCTIONS FOR YOUR OWN SAFETY IMPORTANT: Do not connect battery until fixture is installed. IMPORTANT: An un-switched AC power source of 100VAC to 277VAC is required. This device is designed for use in fixtures listed for dry and damp locations. CAUTION: Make sure all electrical connections conform to the National Electrical Code and all applicable local regulations. CAUTION: Do not let power supply cords touch hot surfaces. CAUTION: Do not mount near gas or electric heaters. CAUTION: Do not use outdoors. CAUTION: Battery is rechargeable type and must be recycled or disposed of properly. Do not use this emergency driver with accessory equipment other than recommended by manufacturer; failure to follow this may cause an unsafe condition. Servicing should only be performed by qualified service personnel. Do not use this emergency driver for other than intended use. Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized personnel. IMPORTANT: Indicator (LED light) illuminated indicates battery in charge mode when AC power is applied. It is recommended and required by applicable code to test emergency function to ensure proper operation of the system; push the test switch for thirty (30) seconds every 30 days to ensure the emergency driver is functioning as LED light source illuminated. Conduct a ninety minute (90) discharge test one time (1) per year; LED light source should be illuminated for a minimum of ninety minutes (90). ASSEMBLY and FIELD INSTALLATION WIRING: WARNING: AC power must be off before proceeding with assembly or installation of emergency driver. TESTING SYSTEM: The emergency battery requires a charge minimum of one (1) hour before testing the circuit. A full charge requires twelve (12) hours. Fulham Head Quarters: Fulham Co., Inc South Van Ness Ave. Hawthorne, CA Manufacturer: North China Fulham Electronic Co. Ltd. No. 9 Xingchang Road, Nanshao Zhen Changping Science Park, Beijing, P.R. China SAVE THESE INSTRUCTIONS Page2of8

3 SELF DIAGNOSTIC INSTRUCTIONS / OPERATION: The self diagnostic feature is factory enabled. The emergency LED driver will conduct a self check for thirty (30) minutes every thirty (30) days and ninety (90) minutes every 12 months. After every self check the LED indicator light will indicate a status signal. A single self-diagnostic test can be activated by pressing the test switch three (3) times. Refer to table 1 for details. The self diagnostic feature can be disabled by using the TPSB-100 SmartSet controller or by using the Smart Set software. The output emergency power is programmable up to 10W for a minimum of 90 minutes (refer to battery chart for information on max load ratings of batteries). TABLE 1 - Self Diagnostic Indications LED Indicator Description LED Indicator Status Signal Description of Status Signal Comment Permanent Green ON System OK AC mode Slow Flashing Green 1.0s ON and 1.0s OFF Self-Diagnostic test underway Flashing Red 4.0s ON and 1.0s OFF Battery not connected Connect the battery Slow Flashing Red 1.0s ON and 1.0s OFF Battery failure Change the battery Fast Flashing Red 0.1s ON and 0.1s OFF Charge circuit is broken Change the driver Green and Red Off OFF (With LED Load ON) DC mode Battery operation (emergency mode) Note: Can take up to one minute for status to be updated when issue is corrected. TPSB-100: For detail information on using TPSB-100 Driver Programming Box, please consult user s manual of TPSB-100. Page3of8

4 Wiring Diagrams 1 TEST TO LED Driver L N GND FHSCP-UNV-10P-L-SD PRG (-) PRG (+) LED (-) LED (+) To LED Driver Output (-) To LED Driver Output (+) BATTERY LINE WALL WHITE(COMMON) GND TO LED Driver BLACK WHITE LED DRIVER RED (+) BLUE (-) Driver Must Be Grounded + - NOTE: DRILL ½ (12.7mm) DIA. HOLE IN MOUNTING PLATE TO INSERT TEST + - LED (+) LED (-) TEST Page4of8

5 Wiring Diagrams 2 LINE WALL BLACK WHITE LED DRIVER RED (+) BLUE (-) Driver Must Be Grounded NOTE: DRILL ½ (12.7mm)DIA. HOLE IN MOUNTING PLATE TO INSERT TEST TEST Page5of8

6 Wiring Diagrams 3 TEST TO LED Driver L N GND FHSCP-UNV-10P-L-SD PRG (-) PRG (+) LED (-) LED (+) BATTERY LINE WALL WHITE(COMMON) GND TO LED Driver BLACK WHITE LED DRIVER RED (+) BLUE (-) Driver Must Be Grounded + - NOTE: DRILL ½ (12.7mm) DIA. HOLE IN MOUNTING PLATE TO INSERT TEST LED (+) LED (-) TEST Battery Chart Fulham Model No. Chemistry Compliant Pack Capacity Max Load for 90 min. Battery Voltage Recharge Time FHSBATL3-1.5-SD RoHS 1500mAh 5W 9.6V 12Hrs FHSBATL3-3-SD RoHS 3000mAh 10W 9.6V 12Hrs FHSBATL9-.6-SD RoHS 1800mAh 6W 9.6V 12Hrs FHSBATL6-1.5L-SD* RoHS 3000mAh 10W 9.6V 12Hrs CAUTION: Replace battery only with corresponding part number. * Note: These batteries do not include mounting means, separate mounting brackets are available. Page6of8

7 Battery Dimensions FHSBATL3-1.5-SD 5W, 1500mAh, 9.6V FHSBATL3-3-SD 10W, 3000mAh, 9.6V FHSBATL9-.6-SD 6W, 1800mAh, 9.6V Page7of8

8 Battery Dimensions FHSBATL6-1.5L-SD 10W, 3000mAh, 9.6V Mounting Bracket Dimensions (Optional) FHSBATSC6-1.5L Page8of8