5000 SERIES POWER SUPPLY/CHARGERS INSTALLATION GUIDE

Transcription

1 5000 SERIES POWER SUPPLY/CHARGERS INSTALLATION GUIDE MODEL# 505 ( VDC OR 4VDC) MODEL# 5500 ( VDC OR 4VDC) MODEL# (0 VDC) MODEL# (5 4VDC) IMPORTANT SAFETY INSTRUCTIONS THIS MANUAL CONTAINS IMPORTANT SAFETY INSTRUCTIONS FOR POWER SUPPLY/BATTERY CHARGER MODELS: 505, 5500, 5600-, BEFORE USING THE BATTERY CHARGER, READ ALL INSTRUCTIONS AND CAUTIONARY MARKINGS ON THE BATTERY CHARGER, BATTERY/BATTERIES AND PRODUCTS USING BATTERIES EMMETT STREET BRISTOL, CT PHONE: (860) FAX: (860) REV. 8/0/00

2 OVERVIEW These access control power supply/chargers are specifically designed for use with access control systems and accessories. These units convert a 5VAC/50-60Hz input into two outputs (see options). Outputs will route power to a variety of access control hardware devices including Mag Locks, Electric Strikes, Magnetic Door Holders, ect. These outputs will operate in both Fail-Safe and Fail-Secure modes SERIES POWER SUPPLY CONFIGURATION REFERENCE CHART DYNALOCK MODEL NUMBER 505 (/4VDC FIELD SELECTABLE) 5500 (/4VDC FIELD SELECTABLE) 5600 ( OR 4VDC FIXED) VDC CURRENT OUTPUT AMP AMPS 0 AMPS 4VDC CURRENT OUTPUT AMP AMPS 5 AMPS OUTPUTS 5VAC/60HZ INPUT CURRENT DRAW.45 AMPS AMP AMPS INPUT FUSE RATING RESETTABLE AMP 4 AMPS AGENCY LISTINGS MEA Approved NYCC Dept. Of Buildings UL LISTINGS & FILE NUMBERS S84 File# E8665 # -9-E INSTALLATION INSTRUCTIONS Wiring methods shall be in accordance with the National Electric Code/NFPA 7/ANSI, and with all local codes and authorities having jurisdiction. Product is intended for indoor use only. ) Mount unit in desired location. mark and pre-drill holes to line up with the top two keyholes in the enclosure. Install two upper fasteners and screws with screw heads protruding. Place the enclosures upper keyholes over the two upper screws, level and secure. Mark the position of the lower two holes. Remove the enclosure and drill the lower two holes. Place the enclosures upper key holes back over the two upper screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pg ). Secure the enclosure to earth ground. ) Set the output voltage: 505, 5500 set the desired output voltage by setting the voltage selector to the appropriate position on the power supply main board. Note: The 5600 is not field selectable and the output voltage must be specified when ordering. ) Secure green/yellow stripe lead to earth ground. Connect AC power (5VAC 60Hz) to terminals marked (H or L, G, N) on the power supply board. Use 8AWG wire or larger for all power connections (Battery, DC output, AC input). 4) Measure output voltage before connecting any devices. This will help prevent damage from occurring. Keep power limited wiring separate from non-power limited wiring (5VAC/60Hz Input, Battery Wires). Minimum.5 spacing must be provided. 5) Connect Fail-Safe or Fail-Secure type locking hardware (e.g. Door strikes, Mag Locks and Electric Deadbolts) positive leads to the terminals marked (+) DC OUTPUT and the negative leads to the terminals marked (-) DC OUTPUT. PAGE

3 INSTALLATION INSTRUCTIONS (CONT D) 6) For access control applications, batteries are optional. When batteries are not used, a loss of AC voltage will result in the loss of output voltage. Batteries must be sealed lead acid rechargeable types if used. Connect one VDC battery to terminals marked (Battery) on the power supply board for VDC operations. Use two VDC batteries connected in series for 4VDC operations. Battery leads are included when batteries are ordered with the power supply. 7) Please insure enclosure cover is secured closed with the provided screw or the key lock option. (+) (-) VDC RECHARGEABLE BATTERY (OPTIONAL) VDC RECHARGEABLE BATTERY (OPTIONAL) Units should be tested at least once a year for proper operation as follows: Output Voltage Test: Under a normal load condition, the DC output voltage should be checked for a proper voltage level. Battery Test: Under normal load conditions, check that the battery is fully charged, check specified voltage at the battery terminals and the board terminals to insure that there is no break in the battery connection wires. Expected battery life is 5 years, however, it is recommended to change the batteries within two years or less if necessary. PAGE

4 GND LINE NEUT OUTPUT STATUS GRN GND BLK LINE DISCONNECT SUPPLY BEFORE CHANGING FUSES F SEE MANUAL REMOTE CONTROL INPUT WHT NEUT F SEE MANUAL RED ( + ) DC IN FROM CONTROLLER RED BLK ( + ) ( - ) BLK ( - ) CUT JUMPER WHEN RELAY IS INSTALLED BATTERY INPUT POWER OUTPUT DynaLock MODELS / POWER SUPPLY/CHARGERS Made in the USA INPUT POWER: OUTPUT POWER: PRIMARY FUSE: OUTPUT FUSE: MODEL MODEL VAC 50-60Hz,.0 Amp 5 VAC 50-60Hz,.0 Amp VDC Nominal (.8 0 Amp 4 VDC Nominal (7.6 5 Amp 4A, 50V Slow-Blow 4A, 50V Slow-Blow () A, 50V Slow Blow () 6A, 50V Slow Blow Note: Refer to 5000 Series Power Supply Installation Manual 5 VAC Power Mains Non-Power Limited Earth Ground Line/Neutral Line/Hot CONTROLLER BONDING WIRE STRAP Green/Yellow Stripe Lead CHASSIS GROUND WIRE Green/Yellow Stripe Lead COVER BONDING WIRE STRAP Green/Yellow Stripe Lead Green Ground Bond Screw AC OUT CONTROLLER CONTROLLER GROUND INPUT WIRE Green/Yellow Stripe Lead GND NEUT LINE CAUTION FAC REMOTE CONTROL INPUT CAUTION: De-energize unit prior to servicing. For continued protection against electric shock and fire hazard, replace fuses with same type and rating (See chart above). Do not expose to rain or moisture. CAUTION: Risk of electric shock. Hazardous live parts inside this power supply are energized from the battery supply even when the input power is disconnected. Battery Connections (Non-Power Limited) CAUTION: This cabinet (compartment) contains vented wet cell batteries. Ventilation of the room in accordance with the rules of the Canadian Electrical Code, Part I, is required. CAUTION: Charge only sealed lead-acid type rechargeable batteries. Other types of batteries may burst causing personal injury and damage. VDC Rechargeable Battery (Optional) VDC Rechargeable Battery (Optional) CAUTION: When power supply board is set for VDC use only () VDC stand-by battery. KEEP POWER LIMITED WIRING SEPARATE FROM NON-POWER LIMITED. USE MINIMUM O.5 SPACING. NOTE: THIS PRODUCT IS INTENDED TO BE USED IN A GENERAL ENVIRONMENT DynaLock Corp. is not responsible for any typographical errors. PAGE 4

5 LINE NEUT GND DYNALOCK CORP. PN50080 PSIOBORD LINE INPUT 0 VAC 60 HZ LINE FUSE F F POWER OUTPUT 4 DynaLock UL Listed General Purpose Power Supply MODEL 5500 POWER SUPPLY/CHARGER Made in the USA INPUT POWER: OUTPUT POWER: PRIMARY FUSE: OUTPUT FUSE: MODEL VAC 50-60Hz,.0 Amp VDC Nominal (.8 Amp or 4 VDC Nominal (7.6 Amp A, 50V Slow-Blow () 5A, 50V Slow Blow Note: Refer to 5000 Series Power Supply Installation Manual 5 VAC Power Mains Non-Power Limited Earth Ground Line/Hot Line/Neutral CONTROLLER BONDING WIRE STRAP Green/Yellow Stripe Lead CHASSIS GROUND WIRE Green/Yellow Stripe Lead Green Ground Bond Screw COVER BONDING WIRE STRAP Green/Yellow Stripe Lead 4V V DC OUTPUT TO DEVICES (Power Limited) BATTERY INPUT CONTROLLER GROUND INPUT WIRE Green/Yellow Stripe Lead CAUTION: Risk of electric shock. Hazardous live parts inside this power supply are energized from the battery supply even when the input power is disconnected. CAUTION: De-energize unit prior to servicing. For continued protection against electric shock and fire hazard, replace fuses with same type and rating (See chart above). Do not expose to rain or moisture. Battery Connections (Non-Power Limited) CAUTION: This cabinet (compartment) contains vented wet cell batteries. Ventilation of the room in accordance with the rules of the Canadian Electrical Code, Part I, is required. CAUTION: Charge only sealed lead-acid type rechargeable batteries. Other types of batteries may burst causing personal injury and damage. VDC Rechargeable Battery (Optional) VDC Rechargeable Battery (Optional) CAUTION: When power supply board is set for VDC use only () VDC stand-by battery. KEEP POWER LIMITED WIRING SEPARATE FROM NON-POWER LIMITED. USE MINIMUM O.5 SPACING. NOTE: THIS PRODUCT IS INTENDED TO BE USED IN A GENERAL ENVIRONMENT DynaLock Corp. is not responsible for any typographical errors. PAGE 5

6 DynaLock UL Listed General Purpose Power Supply MODEL 505 POWER SUPPLY/CHARGER Made in the USA INPUT POWER: OUTPUT POWER: PRIMARY FUSE: MODEL VAC 50-60Hz, 0.45 Amp VDC Nominal (.8 Amp or 4 VDC Nominal (7.6 Amp Resettable PTCC Note: Refer to 5000 Series Power Supply Installation Manual 5 VAC Power Mains Non-Power Limited Earth Ground Line/Hot Line/Neutral CONTROLLER BONDING WIRE STRAP Green/Yellow Stripe Lead CHASSIS GROUND WIRE Green/Yellow Stripe Lead COVER BONDING WIRE STRAP Green/Yellow Stripe Lead F H N G TB 4 VOLT VOLT JP TB TB4 TB DC OUTPUT SHUTDOWN DC OUTPUT TO DEVICES (Power Limited) CONTROLLER GROUND INPUT WIRE Green/Yellow Stripe Lead CAUTION: De-energize unit prior to servicing. The primary fuse is resettable. Reset by correcting the overload condition and de-energizing the unit for at least two minutes. Do not expose to rain or moisture. CAUTION: Risk of electric shock. Hazardous live parts inside this power supply are energized from the battery supply even when the input power is disconnected. Battery Connections (Non-Power Limited) CAUTION: This cabinet (compartment) contains vented wet cell batteries. Ventilation of the room in accordance with the rules of the Canadian Electrical Code, Part I, is required. CAUTION: Charge only sealed lead-acid type rechargeable batteries. Other types of batteries may burst causing personal injury and damage. VDC Rechargeable Battery (Optional) VDC Rechargeable Battery (Optional) CAUTION: When power supply board is set for VDC use only () VDC stand-by battery. KEEP POWER LIMITED WIRING SEPARATE FROM NON-POWER LIMITED. USE MINIMUM O.5 SPACING. NOTE: THIS PRODUCT IS INTENDED TO BE USED IN A GENERAL ENVIRONMENT DynaLock Corp. is not responsible for any typographical errors. PAGE 6

7 5500/5600 OPTIONS FAC Option (Remote Control) Kills all voltage outputs when interfaced with remote dry contact. REMOTE CONTROL MODULE NORMAL MANUAL RESET REMOTE CONTROL MODULE NORMAL MANUAL RESET DB-5 & DB-0 Option (Distribution Board) Two size distribution (5 or 0 position) are available to provide individually fused output terminals for each lock zone. OUTPUT JUMPERS CONNECTOR FOR CM/CMTD MODULE DC INPUT FROM POWER SUPPLY MAIN BOARD RESETTABLE FUSE (SEE NOTE BELOW) WITHOUT CONTROL MODULE OPTION (FACTORY SETTING) WITH CONTROL MODULE OPTION NOTE: RESETTING IS DONE BY FIRST CORRECTING THE OVERLOAD THEN DISCONNECTING THE LOAD OR TURNING OFF THE LINE VOLTAGE FOR TWO MINUTES PAGE 7

8 5500/5600 OPTIONS CM Option (Control Module) Accepts access/egress control dry contact input. Provides SPDT relay output. A B A ACCESS CONTROL INPUT (DRY CONTACTS ONLY) B SPDT DRY CONTACTS RATED AT 4V CMTD Option (Control Module with Time Delay) same as CM Option with Relock Time Delay ADJUSTABLE FOR -80 SECONDS DELAY ON RE-LOCK TIME ATS Option (Anti-Tamper switch) CONTACT HELD OPEN WITH ENCLOSURE COVER CLOSED CONTACT CLOSED WITH ENCLOSURE COVER OPEN WHITE WHITE WHITE WHITE NOTE: ATS switch contacts 4V PAGE 8

9 ILB Option (Interlock Logic Board) Provides Four DPDT Relay Outputs Note: Separate ILB User Manual shows typical wiring diagrams. 5500/5600 OPTIONS COMMON NEGATIVE TERMINAL POSITIVE INPUTS TO ENERGIZE RELAY COILS PAGE 9

10 VOLTAGE VDC 4VDC SINGLE (FULL SIZE) 8 8 INSTALLATION INFORMATION 5600 LOCK CAPACITY DOUBLE SINGLE (FULL SIZE) SINGLE DOUBLE CURRENT DRAW UP TO ½ AMP 9 9 DELAY EGRESS DEADBOLT VOLTAGE 0 AWG 8AWG 6AWG 4AWG AWG 0AWG VDC 4VDC 50FT 50FT 00FT 5FT 50FT 50FT 50FT 550FT 400FT 900FT 65FT 75FT VOLTAGE VDC 4VDC SINGLE (FULL SIZE) LOCK CAPACITY DOUBLE SINGLE (FULL SIZE) SINGLE DOUBLE CURRENT DRAW UP TO ½ AMP DELAY EGRESS DEADBOLT 4 VOLTAGE 0 AWG 8AWG 6AWG 4AWG AWG 0AWG VDC 4VDC 50FT 00FT 00FT 00FT 50FT 00FT 50FT 500FT 400FT 750FT 750FT 500FT These charts indicates the minimum recommended wire size, local codes prevail. PAGE 0

11 TYPICAL 5500/5600 APPLICATION 0 VAC 50/60 HZ INPUT FAC Remote Control E C A B C D E A D B NORMALLY CLOSED DRY CONTACT FROM THE FIRE ALARM CONTROL PANEL (FROM OTHERS) FAIL SAFE LOCKING DEVICE FAIL SECURE LOCKING DEVICE NORMALLY CLOSED ACCESS/EGRESS CONTROLS NORMALLY OPEN ACCESS/EGRESS CONTROLS PAGE

12 5600 TROUBLESHOOTING AC OUT TO SWITCHER DC IN FROM SWITCHER (V OR 4V) ACCESS CONTROL LEGAL RELEASE NO OUTPUT POWER AT A NO OUTPUT POWER AT B CHECK INPUT LINE FUSE 6 CHECK JUMPER SETTING AY CM/CMTD MODULE (IF APPLICABLE) CHECK LINE FUSE 7 CHECK JUMPER SETTING AT DB-5/DB-0 CARD CHECK FOR OR 4VDC FROM SWITCHER 8 CHECK FOR PROPER ACCESS SWITCH CONTACT STATUS 4 CHECK FOR OR 4VDC FROM SWITCHER 9 CHECK LOAD AND EXTERNAL WIRING FOR SHORT CONDITION 5a 5b 5c CHECK F AND F OUTPUT FUSES CHECK THAT FAC MODULE IS SEATED PROPERLY (IF APPLICABLE) TERMINALS AND MUST BE JUMPED TOGETHER IF UNIT HAS FAC MODULE 0 RESET POWER SUPPLY (WITH NO LOAD) BY DISCONNECTING INPUT POWER AT AC LINE IN FOR MINUTES PAGE

13 LINE INPUT 0 VAC 60 HZ 5500 TROUBLESHOOTING ACCESS CONTROL LEGAL RELEASE ELECTROMAGNETIC LOCK NO OUTPUT POWER AT CHECK INPUT LINE POWER CHECK LINE FUSE A 4 CHECK F & F OUTPUT FUSES CHECK FAC (IF APPLICABLE) TERMINALS, AND MUST BE WIRED TO N/C CONTACT 505 TROUBLESHOOTING PRIMARY RESETTABLE FUSE H N G TB F 4 VOLT VOLT JP TB TB4 TB DC OUTPUT SHUT DOWN A DYNALOCK BATTERY CONNECT TO NORMALLY CLOSED DRY CONTACTS TO SHUT DOWN POWER SUPPLY IN CASE OF EMERGENCY POWER SUPPLY SHUTDOWN NO OUTPUT POWER AT A CHECK INPUT LINE POWER RESET POWER SUPPLY (WITH NO LOAD) BY DISCONNECTING POWER AT LEAST FOR MINUTES MAKE SURE YOU HAVE A CLOSURE BETWEEN THE SHUT DOWN TERMINALS PAGE

14 POWER SUPPLY ENCLOSURE.5 SIDE VENT HOLE PATTERN 0.65 DIA. THRU.5 (0 PLACES) TYP. TYPICAL (4 PLACES) (4) #6- x /4 PEM Studs (For Chassis Grounding) TYP X 0.5 SLOT THRU TYP. ( PLACES) / REF. COVER HEIGHT 9GA (0.4) 0.75 TYP. -/4 0.5 C C C C 5.0 CLEAR INSIDE HEIGHT.5.85 TYP TYP TYP..0 CLEAR INSIDE WIDTH 4.0 CLEAR INSIDE DEPTH TYP. C DIA. KNOCK-OUT TYP. (8 LOCATIONS) C.5 TYP. (8 K.O. LOCATIONS).5 TYP. PAGE 4

15 LINE INPUT 0 VAC 60 HZ 5000 SERIES PART LIST AC OUT CONTROLLER GRN BLK WHT GND LINE NEUT DC IN FROM CONTROLLER RED RED BLK BLK ( + ) ( + ) ( - ) ( - ) F TB GND F SEE MANUAL POWER OUTPUT - H TB4 DC OUT PUT LINE NEUT CAUTION DISCONNECT SUPPLY BEFORE CHANGING FUSES OUTPUT STATUS N G TB 4 VOLT VOLT JP TB S HUTDOWN BATTE RY F SEE MANUAL CUT JUMPER WHEN RELAY IS INSTALLED REMOTE CONTROL INPUT 5600 VDC P/N BATTERY INPUT 505 P/N VDC P/N P/N 500 PRIMARY CIRCUIT BOARD PART NUMBERS DB-0 DISTRIBUTION BOARD P/N 5009 DB-5 DISTRIBUTION BOARD P/N 5008 ILB BOARD P/N REMOTE FIRE MODULE (FAC) PLUG IN RELAY 4VDC P/N 5000 VDC P/N REMOTE FIRE MODULE (FAC) PLUG IN RELAY P/N 500 FUSES AMP P/N AMP AMP P/N AMP P/N AMP P/N 5000 AMP P/N 5007 PAGE 5

16 PLEASE DELIVER THIS MANUAL TO THE END USER UPON COMPLETION OF THE POWER SUPPLY INSTALLATION FOR PRODUCT SUPPORT AND PARTS ORDERING INFORMATION CONTACT: DynaLock Corp. 705 Emmett Street Bristol, CT 0600 Bus: (877) Toll-Free USA (860) Fax: (860) DYNALOCK ON THE INTERNET: Website: QQFU/QQFU7 Power Supplies, General Purpose