GENERAL CATALOG

Transcription

1 LOAD CELLS GENERAL CATALOG ZSE Electronic Mess-Systeme & Sensortechnik GmbH In den Freßäckern 28 D Bietigheim-Bissingen Telefon: Fax: info@zse.de -

2 2-9 Load Cell Selection Chart For Compression Load Measurement 5 N kn MN Ref. Page Small-Sized Ultra-Small Compression Load Cells LMB-A Beam-Type Load Cells Small-Sized for Load Distribution Measurement LMA-A Ultra-Small LMBT-A Compact and Lightweight LUB-B Small-Sized Compression Load Cells Small-Sized Compression Load Cells Connector-Equipped LCX-A-ID Stainless Steel Make LCN-A Load Cell Selection Chart Compression Load Cells Small-Sized Compression Load Cells Small-size Compression Load Cells Beam-Type Load Cells Small-Sized Large-Capacity Compression Load Cells Explosion-Proof Compression Load Cells For High Temperature LC-FH Diameter:21mm LMR-S-SA2 High Output, High Accuracy LMC-A Accuracy:1/00 LUB-C Diameter: or 25mm LCR-G-SA2 Explosion-Proof LCS-D Thin Compression Load Cells As Thin as 25 to mm in Total Height LCK-A 2-27 Stainless Steel LC-J Built to order 2-30 Corrosion- Resistant Compression Load Cells Accuracy 1/00 LC-V Accuracy 1/00 LCH-F High- Accuracy Load Cells General Purpose Load Cells Large Capacity,Accuracy:1/0 LCV-A Large Capacity LC-E Built to order

3 2-10 Thin Load Cells N kn Ref. Page Stainless Steel Load Cell Thin Load Cell For Food Tanks and Hoppers LCTS-B For Tanks and Hoppers LCTA-A For Tanks and Hoppers LCTB-A For Tanks and Hoppers LCTE-A For Tanks and Hoppers LCTD-A For Tension Load Measurement mn N kn Ref. Page Load Cells for Minute Load Measurement High-Accuracy Tension Load Cells Tension Load Cells Vertical Load to Rod LVS-A Horizontal Load to Rod LTS-A High-Accuracy Tension Load Cells LTZ-A LT-FH for High Temperature LT-FL for Low Temperature LT-F (H L) Load Cell Selection Chart For Tension/Compression Loads Small-Capacity Small Capacity Tension/ Compression Load Cells LU-A Diameter 28mm, Weight g Compact Tension/ LUR-A-SA1 Compression Load Cells Compact Tension/ Compression Load Cells High-Accuracy Tension/ Compression Load Cells Tension/ Compression Load Cells LUX-B-ID Inert Gas Sealed LU-E Built to order Accuracy:1/00 LUH-F Thin, large Capacity LUK-A N kn MN Ref. Page With tension/compression load cells, Tension load causes plus output compression load, minus output 2-10

4 2-11 Load Cell Selection Chart For Component Force Measurement 3-Component Force Transducers Component Force Measurement LSM-B-SA1 6-Component 6-Component Force Measurement Force Transducers LAT-0A Compact 6-Component Force Measurement 6-Component Force Transducers LFM-A Compact 6-Component Force Measurement 6-Component Force Transducers with Built-in Amplifier LFX-A N kn Ref. Page For Special Purposes (Load Cells for Steel making Line ) kn MN Ref. Page Load Cell Selection Chart Tension Meter Load Cell Washer- Type Load Cell For Tension Meter LCR-B-S7 Washer-Type for Rolling Mill LCW-D-S Washer-Type for Rolling Mill LCW-E-S For Special purposes kn MN Ref. Page Washer- Type Load Cells Pin-Type Load Cells Different Diameters Available LCW-C-SA3 For Pulley Axis of Crane LTP-S-S Jack Load Cells For Jack LUR-B-SA One-End Revolving Tension Load Cells For Rope Tension Measurement LTR-S-SA Crane Load Cells 1 to 5V Output Available LTA-C-S 2-67 Rectangular Load Cells For Pillow Block Load LCD-A-S

5

6 2-13 LMA-A 12 mmφ, 4 mm Thick(5 to N) 5 N to 1 kn Small-Sized Compression Load Cells LMA-A-5 to N LMA-A-N to 1KN TEDS-installed versions can be manufactured. Inquiries are welcome. Nonlinearity : Within ±1% RO Hysteresis : Within ±1% RO Repeatability : 1% RO or less Rated Output : 0.6 to 2 mv/v (10 to 00 μm/m) (LMA-A-5N) 0.75 to 2 mv/v (10 to 00 μm/m) (LMA-A-10N to 1KN) Note : Rated output is sorted to one of the classes divided by every 2% difference in output value. Since the rated output stated in the Test Data Sheet is the center value of the class, it may have a maximum error of ±1%. Safe Temperature Range :-10 to C (however, noncondensing) Compensated Temperature Range : 0 to C (however, noncondensing) Temperature Effect on Zero Balance : Within ±0.3% RO/ C (LMA-A-5N) Within ±0.2% RO/ C (LMA-A-10N to N) Within ±0.05% RO/ C (LMA-A-N to 1KN) Temperature Effect on Output Within ±0.2%/ C (LMA-A-5N to N) Within ±0.05%/ C (LMA-A-N to 1KN) Compact, Lightweight, Low Price Suitable for Load Distribution Measurement Compact and lightweight LMA-A series load cells can be used by merely putting or bonding on the measurement point or setting in a hollow. Mount Base CFM-A 7V AC or DC Excitation Voltage : 1 to 5 VAC or DC 3Ω±2.5% 3Ω±2.5% Cable: 4-conductor (0.035 mm 2 ) vinyl shielded cable, 1.7 mm diameter by 2 m long, bared at the tip (Shield wire is not connected to mainframe.) Safe Overload Rating : 1% Natural Frequency : See table below. See table below. Material : A copper alloy and more than N are stainless steel. Protection Rating : IP64 JIS C 09 splash-proof type Optional Accessory Mount Base CFM-A 25 CFM-5A CFM-A 32 A φa Material: Aluminum alloy Thickness LMA-A-5N LMA-A-10N LMA-A-N LMA-A-N LMA-A-N LMA-A-0N LMA-A-0N LMA-A-1KN Rated Capacity 5N 10N N N N 0N 0N 1kN Natural Frequency 15.3kHz 17.5kHz 24.8kHz 32.6kHz 21.6kHz 29.7kHz 43.9kHz 53kHz Weight * 1.5g CFM-5A 11g Mount Base CFM-A *not including cable SR SR (0.2) (6) (1.65) (1) 19.4 (5) (3.4) Bared at the tip LMA-A-5 to N LMA-A-N to 1KN Physical quantity indication Static measurement Dynamic measurement 2-13 LMA-A WGA-6B WGI-0A Data Loggers UCAM-B 3-25 Strain Amplifiers DPM-900 Series Universal Recorders EDX-A

7 LMB-A Small-Sized Compression Load Cells 10 N to 2 kn 2-14 LMB-A-0N to 2KN LMB-A-10 to 0N TEDS-installed versions can be manufactured. Inquiries are welcome. Compact, Lightweight, Low Price Suitable for Load Distribution Measurement Ultra-small and lightweight LMB-A series load cells can be used by merely putting or bonding on the measurement point or setting in a hollow. (Patent pending) : See table below. Nonlinearity : Within ±0.5% RO Hysteresis Within ±0.5% RO: Repeatability : Within ±0.3% RO Rated Output : 1.4mV/V(μm/m) or more Note : Rated output is sorted to one of the classes divided by every 1% difference in output value to the rated capacity. Since the rated output stated in the Test Data Sheet is the center value of the class, it may have a maximum error of ±0.5%. Safe Temperature Range : -10 to C (noncondensing) Compensated Temperature Range : 0 to C (noncondensing) Temperature Effect on Zero Balance : Within ±0.1% RO/ C (LMB-A-N) Within ±0.05% RO/ C (LMB-A-N to 2KN) Temperature Effect on Output Within ±0.05%/ C 7V AC or DC Excitation Voltage : 1 to 5V AC or DC 3Ω±2.5% 3Ω±2.5% Cable : 4-conductor (0.035 mm 2 ) vinyl shielded cable, 1.7 mm diameter by 2 m long, bared at the tip (Shield wire is not connected to mainframe.) Safe Overload Rating : 1% Natural Frequency : See table below. Material : Stainless steel 10 to 0N : approx. 1.5g (not including cable) 0N to 2kN : approx. 6g (not including cable) Protection Rating : IP64 JIS C 09 splash-proof type LMB-A-10N LMB-A-N LMB-A-N LMB-A-0N LMB-A-0N LMB-A-1KN LMB-A-2KN 10N N N 0N 0N 1kN 2kN Natural Frequency 32kHz khz 47kHz 59kHz 37kHz 45kHz 54kHz 0.4 ( 2.9) SR3 ( 3.2) 1 ( 4.6) SR6 ( 3.5) (18) 16 (21) Bared at the tip LMB-A- to 0N LMB-A-0N to 2KN Physical quantity indication Static measurement Dynamic measurement LMB-A WGA-6B WGI-0A Data Loggers UCAM-B 3-25 Strain Amplifiers DPM-900 Series Universal Recorders EDX-A

8 2-15 LMBT-A Small-Sized Compression Load Cells High-Temperature N to 2kN LMBT-A-0N~2KN LMBT-A-~0N TEDS-installed versions can be manufactured. Inquires are welcome Ultra-Small Sized, Lightweight. Suitable for Load Distribution Measurement Ultra-small and lightweight. For High temperature by C. Merely putting or bonding on the measurement point or setting in a hollow. Nonlinearity : Within ±0.3% RO Hysteresis : Within ±0.3% RO Repeatability : Within ±0.3% RO Rated Output : 1.4 mv/v (μm/m) or more Note: Rated output is sorted to one of the classes divided by every 1% difference in output value to the rated capacity. Since the rated output stated in the Test Data Sheet is the center value of the class, it may have a maximum error of 0.5%. Safe Temperature Range : Compensated Temperature Range : Temperature Effect on Zero Balance : Temperature Effect on Output : - to 1 C (noncondensing) -10 to C (noncondensing) Within ±0.05% RO/ C Within ±0.05%/ C 7V AC or DC Excitation Voltage : 1 to 5V AC or DC 3Ω±2.5% 3Ω±2.5% Cable : 4-conductor (0.035 mm 2 ) vinyl shielded cable, 1.7 mm diameter by 2 m long, bared at the tip (Shield wire is not connected to mainframe.) Safe Overload Rating : 1% Natural Frequency : See table below. Material : Stainless steel to 0N: Approx. 1.5g (not including cable) 0N to 2kN: Approx. 6.5g (not including cable) Protection Rating : IP64 JIS C 09 splash-proof type LMB-A-N LMB-A-N LMB-A-0N LMB-A-0N LMB-A-1KN LMB-A-2KN N N 0N 0N 1kN 2kN Natural Frequency khz 47kHz 59kHz 37kHz 45kHz 54kHz 0.4 ( 2.9) SR3 3 1 ( 4.6) SR (10) 16 (10) Bared at the tip LMBT-A- to 0N LMBT-A-0N to 2KN Physical quantity indication Static measurement Dynamic measurement 2-15 LMBT-A WGA-6B WGI-0A Data Loggers UCAM-B 3-25 Strain Amplifiers DPM-900 Series 3-5 Memory Recorder/Analyzers EDX-3000A 3-79

9 LMR-S-SA2 Small-Sized Compression Load Cells 21 mmφ, 10 mm Thick 2 to kn 2-16 LMR-S-KNSA2 TEDS-installed versions can be manufactured. Inquiries are welcome. Compact,Lightweight, Low price, Suitable for Load Distribution Measurement Compact and lightweight LMR-S-SA2 series load cells can be used by merely putting or bonding on the measurement point or setting in a hollow. Major applications include measurement of load distribution by using multiple units, load measurement in pipe making mill or where a measuring site or the weight of load cell itself is limited. Nonlinearity : Within ±1% RO (LMR-S-2KNSA2 to 10KNSA2) Within ±2% RO (LMR-S-KNSA2) Hysteresis : Within ±1% RO (LMR-S-2KNSA2 to 10KNSA2) Within ±2% RO (LMR-S-KNSA2) Repeatability : ±1% RO or less Rated Output : 1 mv/v (00 μm/m) or more Safe Temperature Range : -10 to C Compensated Temperature Range : 0 to C Temperature Effect on Zero Balance : Within ±0.05% RO/ C Temperature Effect on Output : Within ±0.05%/ C 7V AC or DC Excitation Voltage : 1 to 2V AC or DC 3Ω±2% 3Ω±2% Cable : 4-conductor (0.035 mm 2 ) vinyl shielded cable, 1.7 mm diameter by 2 m long, bared at the tip (Shield wire is connected to mainframe.) Safe Overload Rating : 1% Natural Frequency : Approx.kHz Approx.25g Material : Stainless steel LMR-S-2KNSA2 LMR-S-5KNSA2 LMR-S-10KNSA2 LMR-S-KNSA2 2kN 5kN 10kN kn Users should be cautioned that operating conditions may adversely affect the stated specifications. SR3 SR Bared at the tip LMR-S to 2KNSA2 LMR-S-5 to KNSA2 Physical quantity indication Dynamic measurement LMR-S-SA WGA-6B WGA-6B WGI-0A Strain Amplifiers DPM-900 Series 3-5 Memory Recorder/Analyzers EDX-3000A

10 2-17 LMC-A Small-Sized Compression Load Cells 5 to kn LMC-A-5KN,10KN TEDS-installed versions can be manufactured. Inquiries are welcome. Compact and high output accuracy Suitable for load distribution measurement Compact and lightweight load cells can be used by merely placing or bonding on the load site, setting in a hollow, or affixing with a mounting band. Major applications include measurement of load distribution by using multiple units, load measurement in pipe making mills, or where a measuring site or the weight of the load cell itself is limited. To Ensure Safe Usage LMC-A-KN LMC-A-KN Subject metal Given that this is a compact high capacity device, this gives high surface pressure on the mounting surface when at rated load. For the mounting seat material, use HRC or better metals such as Mounting surface SUS630-H900. Example of recommend materials Subject metal material: HRC (35 to 38), SCM4, etc. Mounting surface material: HRC or better, SUS630-H900 SCM4, etc. Nonlinearity : Within ±0.5% RO (within ±1%RO kn, kn) Hysteresis : Within ±0.5% RO (within ±1%RO kn, kn) Repeatability : Within 0.5% RO Rated Output : 1.5 mv/v (3000 μm/m) or more Safe Temperature Range : -10 to C Compensated Temperature Range : 0 to C Temperature Effect on Zero Balance : Within ±0.05% RO/ C Temperature Effect on Output : Within ±0.05%/ C 7V AC or DC Excitation Voltage : 1 to 6V AC or DC 3Ω±2% 3Ω±2% Cable : 4-conductor (0.035 mm 2 ) vinyl shielded cable, 2 m long, 1.7 mm diameter, bared at the tip (Shield wire is not connected to mainframe) Safe Overload Rating : 1% Natural Frequency : See table below See table below (not including cable) Material : Stainless steel Protection rating : IP64 JIS C 09 splash-proof type RoHS Directive EN581 LMC-A-5KN LMC-A-10KN LMC-A-KN LMC-A-KN 5kN 10kN kn kn Natural Frequency 32kHz 38kHz 41kHz 29kHz Weight (approx.) 5g 6g 10g 30g *Operating conditions may adversely affect characteristics. For details, please consult the instruction manual. No foreign substance in the hole size 4.2 SR10 (Don t insert a pin.etc) C SR15 C LMC-A-5KN LMC-A-10KN SR C LMC-A-KN C SR LMC-A-KN Bared at the tip Physical quantity indication Dynamic measurement 2-17 LMC-A WGA-6B WGA-6B WGI-0A Strain Amplifiers DPM-900 Series 3-5 Memory Recorder/Analyzers EDX-3000A 3-79

11 LCN-A Compact, Stainless Steel Case 0 N to kn Small-Sized Compression Load Cells 2-18 TEDS-installed versions can be manufactured. Inquiries are welcome. : See table at the left. Nonlinearity : Within ±0.15% RO Hysteresis : Within ±0.1% RO Repeatability : 0.05% RO or less Rated Output : 2 mv/v (00μm/m) ±0.3% Safe Temperature Range : - to C Compensated Temperature Range : -10 to C Temperature Effect on Zero Balance : Within ±0.005% RO/ C Temperature Effect on Output : Within ±0.01%/ C V AC or DC Excitation Voltage : 1 to 12V AC or DC 3Ω±0.5% 3Ω±0.5% Cable : 4-conductor (0.5 mm 2 ) chloroprene shielded cable, 8.5mm diameter by 3m long, with press-fit terminal for 4 mm (Shield wire is not connected to mainframe.) Compact,Corrosion-Resistant Stainless Steel Enclosure Hermetically Sealed Structure with Inert Gas Filled in Compact and lightweight design facilitates installation into existing facilities. Excellent stability and reliability are ensured by the hermetically-sealed structure with inert gas filled in. Furthermore, the stainless steel (SUS 630) enclosure makes them widely usable as sensors for equipment requiring corrosion resistance. Inner Plate CAI-2 Inner plate is intended to protect the load sensing part at the top of load cell. It prevents the sphere from being flattened due to frequent impact loads. Inner plate CAI-2 LCN-A 30 Safe Overload Rating : 0% Natural Frequency : See table below 2 g Material : Main unit : SUS 630 Bottom plate : SUS 304 LCN-A-0N LCN-A-1KN LCN-A-2KN LCN-A-5KN LCN-A-10KN LCN-A-KN with Saddle and Mount Base Mounted In Combination with Saddle CA and Mount Base CF Saddle CA-2F LCN-A 0N 1kN 2kN 5kN 10kN kn at equal distance 4 7 at equal distance Natural Frequency 6.4kHz 5.3kHz 7.6kHz 13kHz 18kHz 24kHz SR R Mount Base CF Hexagon socket head bolt 4-M5 L=10 4 M5 d=5 (37) *0N :R1 Hexagon socket head bolts to connect the load cell and mount base are attached to the mount base. Saddle and Mount Base 42 Dedicated for LCN-A Saddle CA-2F Mount Base CF-42 Physical quantity indication Static measurement Dynamic measurement LCN-A-0N 2KN LCN-A-5 KN SR Bared at the tip LCN-A Data Loggers UCAM-B 3-25 Memory Recorder/Analyzers EDX-3000A

12 2-19 LCX-A-ID 28mmφ, 18 mm Thick(0N to 2kN) 0N~kN Small-Sized Compression Load Cells TEDS installed (for TEDS, refer to page 9-16) Compact, Lightweight and Thin Easy to Incorporate into Equipment This is a compact, lightweight, and thin load cell, easy to incorporate into existing equipment. The mainframe is an all-stainless steel product. Additionally, the cable is connected using a connector, therefore there are no problems with wiring when situating, and cable replacement is easy. Work is also possible if the cable is replaced with one resistant to repeated bending (flexible cable). Please add M1Z3K to the end of the model name. Nonlinearity : Within±0.1% RO Hysteresis : Within±0.1% RO Repeatability : 0.05% RO or less Rated Output : 1.0 mv/v (00μm/m) or more (LCX-A-0N-ID) 1.5 mv/v (3000μm/m) or more (LCX-A-1KN to KN-ID) Safe Temperature Range : - to C Compensated Temperature Range : -10 to C Temperature Effect on Zero Balance : Within ±0.01% RO/ C (LCX-A-0N-ID) Within ±0.005% RO/ C (LCX-A-1KN to KN-ID) Temperature Effect on Output : Within ±0.005%/ C 15V AC or DC Excitation Voltage : 1 to 10V AC or DC 375Ω±5Ω 3Ω±3.5Ω Dedicated connection cable : TE-45 Included cable : 6-conductor (0.08 mm 2 ) chloroprene shielded cable, 4.4 mm diameter by 3 m long, terminated with connector plug to the transducer side and bared at the other side (Shield wire is not connected to mainframe.) Safe Overload Rating : 1% Safe Lateral Load Rating : 15% the rated capacity Natural Frequency : See table below. Material : SUS, metallic finish Approx. 45g (0N to 2kN) (not including cable) Approx. 1g (5 to kn) (not including cable) Protection Rating : IP67 (Watertight structure conforming to JIS C 09) LCX-A-0N-ID LCX-A-1KN-ID LCX-A-2KN-ID LCX-A-5KN-ID LCX-A-10KN-ID LCX-A-KN-ID 0N 1kN 2kN 5kN 10kN kn Natural Frequency 24kHz 29kHz 37kHz 24kHz 28kHz 37kHz SR30 4 SR (53) 43 (53) M2 d=2.2, equal distance, P.C.D25 (95) Minimum mounting dimension with cable bent M3 d=3.2, equal distance, P.C.D38 () Minimum mounting dimension with cable bent Press-fit terminal TEDS compatible LCX-A-0N to 2KN LCX-A-5 to KN 2-19

13 with Saddle and Mount Base Mounted In Combination with Saddle (CA) and Mount Base (CX) at equal distance Saddle CA-2F 9 LCX-A-0N to 2KN-ID at equal distance for Mount Base Mount Base CX-5 Weightg Mount Base CX-7 Weight2g Hexagon socket head bolt M2 L=8 (attached to CX-5) at equal distance Mount Base CX-5 Saddle CA-2F 17 9 LCX-A-5~KN-ID at equal distance Mount Base CX-7 Hexagon socket head bolt M3 L=10 (attached to CX-7) , 5 depth of counterbore , 7 depth of counterbore Physical quantity indication Static measurement Dynamic measurement LCX-A-ID WGA-6B Data Loggers UCAM-B 3-25 Strain Amplifiers DPM-900 Series 3-5 Universal Recorders EDX-A 3-65 Memory Recorder/Analyzers EDX-3000A

14 2-21 LC-V Nonlinearity : within±0.05%ro to 0 kn Small-Sized Compression Load Cells Steady brace CR is available. (See page 2-22) TEDS-installed versions can be manufactured.inquiries are welcome. Nonlinearity : Within±0.05% RO Hysteresis : Within±0.05% RO Repeatability : 0.03% RO or less Rated Output : 2.5 mv/v (00μm/m) ±0.2% Safe Temperature Range : - to C Compensated Temperature Range : -10 to C Temperature Effect on Zero Balance : Within ±0.003% RO/ C Temperature Effect on Output : Within ±0.003%/ C V AC or DC Excitation Voltage : 1 to 10V AC or DC 3Ω±0.5% 3Ω±0.5% Cable : 4-conductor (0.5 mm 2 ) chloroprene shielded cable, 8.5mm diameter by 5m long, with press-fit terminal for 4 mm (Shield wire is not connected to mainframe.) Compact and lightweight Nonlinearity : within±0.05%ro Hermetically sealed structure with inert gas filled in Service life: 10 million times or more BISELCOM gage is used. Compact and lightweight design facilitates installation into existing facilities. While nonlinearity of within 1/00 is ensured, the hermetically-sealed structure with inert gas filled in enables highly stable and reliable measurement. (Patented) Safe Overload Rating : 1% Natural Frequency : See table below. See table below. Protection Rating : IP67(Watertight type conforming to JIS C 09) C D G 21 SR 4 4 A E B (F) R1/2 Cable protective rubber tube H 4 J Press-fit terminal LC-5TV LC-10TV LC-TV Natural Frequency A B φc φd E (F) G φh J SR kn kn 0kN 17kHz 16kHz 15kHz M5 M6 M8 1 Weight * 1kg 1.3kg 3.1kg *not including cable Physical quantity indication Static measurement Dynamic measurement 2-21 LC-V WGA-6B Data Loggers UCAM-B 3-25 Strain Amplifiers DPM-900 Series 3-5 Universal Recorders EDX-A 3-65 Memory Recorder/Analyzers EDX-3000A 3-79

15 CR Special Accessories Steady Braces in Combination 2-22 Load Cell LC-V in Combination with Steady Brace CR (E) F B C D Load Cell 4 15at equal distance A Steady Braces for Hopper scale with Rolling Prevention Mechanism This product is a bracket used when fitting a hopper scale with a load cell in place of a load striker plate or mounting base. Using this product cancels out horizontal displacement caused by thermal expansion from the tank itself, and resulting lateral load. F 1 Load Cell LC-5TV LC-10TV LC-TV B Installation Example 4 15at equal distance 234 Steady Brace A φb φc φd (E) F CR-5 CR-10 CR Weight 7kg 8.5kg 15.6kg To Ensure Safe Usage To prevent the hopper from falling down, the hopper's center of gravity should be low enough from the installation position of load cell. When the stirrer etc. are carried in equipment, it is not suitable for use under oscillating environment. Steady braces and load cell will be assembled and shipped out. (The upper and the lower part are fixed)(fig.1.) Please be sure to order an assembled load cell with steady braces. (It is option) Please do not decompose before installation. If you already have the load cell (LC-V),we take it and have it assembled with steady braces. (it is option) Hopper Flange viewed from top Load cell Enlarged Support Flange Steady brace Behavior of Steady Brace Against Lateral Force Rubber bolt Load cell Clearance Horizontal displacement Load cell Fig. 1. When at the installation Fig. 2. Normal condition Fig. 3. At horizontal displacement 1In the event of horizontal displacement as in Fig. 2, the internal load cell will tilt as in Fig. 3, and in this example, the top of the vibration prevention bracket will move to the right. 2When the lateral force is removed, the load cell and and steady brade return to the normal condition shown in Fig

16 2-23 LCV-A Small-Sized Compression Load Cells Compact and Large Capacity 0 kn & 1 MN TEDS-installed versions can be manufactured.inquiries are welcome. Nonlinearity : Within±0.1% RO Hysteresis : Within±0.1% RO Repeatability : 0.05% RO or less Rated Output : 2.5 mv/v (00μm/m) ±0.2% Safe Temperature Range : - to C Compensated Temperature Range : -10 to C Temperature Effect on Zero Balance : Within ±0.005% RO/ C Temperature Effect on Output : Within ±0.005%/ C V AC or DC Excitation Voltage : 1 to 10V AC or DC 3Ω±0.5% 3Ω±0.5% Cable : 4-conductor (0.5 mm 2 ) chloroprene shielded cable, 8.5 mm diameter by 5 m long, with press-fit terminal for 4 mm (Shield wire is not connected to mainframe.) Compact and Lightweight Nonlinearity : 1/0 Safe Overload Rating : 1% Natural Frequency & See table below. Protection Rating : IP67 (Watertight type conforming to JIS C 09) Service life : 10 million times or more BISELCOM gage is used. LCV-A series is a compact and lightweight load cell developed for large capacity of 0kN and 1MN. They can easily be installed into existing facilities. The hermetically-sealed structure with inert gas filled in ensures stable and reliable performance with 1/0 nonlinearity. Use of BISELCOM gage ensures increased output and improved reliability. F 21 (E) C D SR B A BISELCOM gage is a self temperature compensated gage with the sensitivity temperature compensation function added. R1/2 H G 4 J Bared at the tip LCV-A-0KN LCV-A-1MN Natural Frequency A B φc φd (E) F φg φh J SR 0kN 13kHz M10 d= MN 12kHz M12 d=18 1 in Combination with Accessories C B E 4 J at equal distance Weight 6kg 10kg 3 M8 d= at equal distance 8 H G F D K L A In Combination with Saddle CA and Mount Base CF Hex. socket Load Cell A Saddle Mount Base φb φc φd φe φf φg φh φj K L Head Bolt LCV-A-0KN CA-B CF-113F 4xM10 L= LCV-A- 1MN CA-1MH CF-130F 4xM12 L= Hexagon socket head bolts to connect the load cell to the mount base are attached to the mount base. Physical quantity indication Static measurement Dynamic measurement 2-23 LCV-A WGA-6B WGA-6B Data Loggers UCAM-B 3-25 Strain Amplifiers DPM-900 Series 3-5 Memory Recorder/Analyzers EDX-3000A 3-79

17 LCR-G-SA2 φ&25mm 10 to kn Small-Sized Large-Capacity Compression Load Cells 2-24 Compact, Lightweight, Large Capacity Measurement for Cylinder. Since the diameter is small and the cable comes from the bottom, LCR-G-SA2 series load cells can be inserted into cylindrical object for measurement. Nonlinearity : Within ±1% RO Hysteresis : Within ±1% RO Rated Output : 1 mv/v (00μm/m) or more Safe Temperature Range : -10 to C Compensated Temperature Range : 0 to C Temperature Effect on Zero Balance : Within±0.1% RO/ C Temperature Effect on Output : Within±0.05%/ C 7V AC or DC Excitation Voltage : 1 to 2V AC or DC 3Ω±5% 3Ω±5% Cable : 4-conductor (0.05 mm 2 ) chloroprene shielded cable, 3 mm diameter by 5 m long, terminated with connector plug (Shield wire is not connected to mainframe.) Safe Overload Rating : 1% See table below Material : Metallic LCR-G-10KNSA2 LCR-G-KNSA2 LCR-G-30KNSA2 LCR-G-KNSA2 10kN kn 30kN kn Weight * g 130g *not including cable 18 Load SR Load SR30 LCR-G-10KNSA2 LCR-G-KNSA2 LCR-G-30KNSA2 φa A (12.5) (7.5) M3 d=6 2 M3 d=6 Connector plug LCR-G-10 to 30KNSA2 LCR-G-KNSA2 Physical quantity indication Static measurement Dynamic measurement LCR-G-SA2 WGA-6B WGI-0A Data Loggers UCAM-B 3-25 Strain Amplifiers DPM-900 Series 3-5 Universal Recorders EDX-A

18 2-25 LC-E General-Purpose Compression Load Cells Large Capacity 2 & 5 MN Watertight type (JIS C 09) is also available. TEDS-installed versions can be manufactured.inquiries are welcome. Nonlinearity : Within±0.5% RO Hysteresis : Within±0.2% RO Repeatability : 0.1% RO or less Rated Output : 2 mv/v (00μm/m) ±1% Safe Temperature Range : -30 to 85 C Compensated Temperature Range : -10 to C Temperature Effect on Zero Balance : Within±0.005% RO/ C Temperature Effect on Output : Within±0.005%/ C V AC or DC Excitation Voltage : 1 to 10V AC or DC 3Ω±0.5% 3Ω±0.5% Cable : 4-conductor (0.3 mm 2 ) chloroprene shielded cable, 7.6 mm diameter by 5 m long, terminated with connector plug (Shield wire is connected to mainframe.) High Stability and Hermetically Sealed Structure with Inert Gas Filled in. Inert Gas is filled in the detector portion, thereby preventing aging deterioration and ensuring a stable and reliable operation. Safe Overload Rating : 1% Natural Frequency : See table below. See table below. B A R1/2 In with saddle (standard accessory) C SR Connector plug 6 F d= D E LC-0TE LC-0TE 2MN 5MN Natural Frequency 3.5kHz 4kHz A B φc φd φe F SR Weight * M14 M kg 65kg *not including cable Physical quantity indication Static measurement Dynamic measurement 2-25 LC-E WGA-6B WGA-6B Data Loggers UCAM-B 3-25 Strain Amplifiers DPM-900 Series 3-5

19 LC-FH High Temp. Compression Load Cells High-temperature -10 to 1 C 0N to 0kN 2-26 TEDS-installed versions can be manufactured. Inquiries are welcome. : See table below Nonlinearity : Within ±0.5%RO Hysteresis : Within ±0.5%RO Repeatability : 0.05% RO or less Rated Output : 1.5mV/V ( 3000μm/m) ±0.2% Safe Temperature Range : -10 to 1 C (Excluding connector part) Compensated Temperature Range : -10 to 1 C (Excluding connector part) Temperature Effect on ZERO Balance : Within ±0.005%RO/ C Temperature Effect on Output : Within ±0.01%/ C VAC or DC Excitation Voltage : 1 to 10V AC or DC 3Ω±0.5% 3Ω±0.5% Cable : 4-conductor (0.03mm 2 ) fluoroplastic shielded cable, 5mm diameter by 5m long, terminated with connector plug. (Shield wire is not connected to mainframe) High Reliability, Airtight Structure, Selectable from a Wide Range of Rated Capacities. Able to continuously operate under temperatures up to 1 C without any external cooling. Safe Overload Rating : 0% Natural Frequency : See table below See table below LC-KFH LC-KFH LC-0KFH LC-0KFH LC-1TFH LC-2TFH LC-5TFH LC-10TFH LC-TFH 0N 1kN 2kN 5kN 10kN kn kn kn 0kN Natural Frequency 3.2kHz 5.1kHz 7.2kHz 11kHz 17kHz 21kHz 16kHz 11kHz 8.6kHz Weight * 0g 0g 2.0kg 3.4kg 7.0kg *not including cable C R1/2 4 F d=12 SR D A (B) LC-KFH LC-KFH LC-0KFH LC-0KFH LC-1TFH LC-2TFH LC-5TFH LC-10TFH LC-TFH A (B) φc φd φe F SR M M5 M5 M8 M8 M E Connector plug Physical quantity indication Static measurement Dynamic measurement LC-FH WGA-6B WGA-6B Data Loggers UCAM-B 3-25 Strain Amplifiers DPM-900 Series 3-5 Universal Recorders EDX-A

20 2-27 LCK-A Thin Compression Load Cells 25 mm Thick(5 to kn) 5 to 0 kn TEDS-installed versions can be manufactured. Inquiries are welcome. Thin Design,High Reliability, Hermetically-Sealed Structure with Inert Gas Filled in The LCK-A series load cells have excellent accuracy, reliability, stability, and response. They also have a thin design for convenient installation as detection terminals of weighing systems. This thin design makes them suitable for applications such as conveyors, vehicles, cranes, hoppers, and tanks where the space, especially the height, is limited and the detecting part needs to be downsized. Nonlinearity : Within±0.2% RO (LCK-A-5KN to KN) Within±0.5% RO (LCK-A-0KN) Hysteresis : Within±0.2% RO (LCK-A-5KN to KN) Within±0.5% RO (LCK-A-0KN) Repeatability : 0.05% RO or less Rated Output : 2 mv/v (00μm/m) ±0.5% Safe Temperature Range : -30 to C Compensated Temperature Range : -10 to C Temperature Effect on Zero Balance : Within ±0.007% RO/ C Temperature Effect on Output : Within ±0.005%/ C V AC or DC Excitation Voltage : 1 to 10V AC or DC 3Ω±0.5% 3Ω±0.5% Cable : 4-conductor (0.3 mm 2 ) chloroprene shielded cable, 7.6 mm diameter by 5 m long, with bared at the tip (Shield wire is not connected to mainframe.) Safe Overload Rating : 1% Natural Frequency : See table below See table below 4 G d=h F SR 21 E R1/2 Rubber tube for cable protection D A B C (44) Bared at the tip LCK-A-5KN LCK-A-10KN LCK-A-KN LCK-A-KN LCK-A-KN LCK-A-0KN 5kN 10kN kn kn kn 0kN Natural Frequency 10.7kHz 11.4kHz 14.2kHz 24.2kHz 14.8kHz 12.6kHz Physical quantity indication A B φc D φe φf G H SR M5 M8 M8 M Dynamic measurement Weight * 0g 1.5kg 2.2kg 3.5kg *not including cable 2-27 LCK-A WGA-6B WGA-6B Channel Signal Conditioner WGC-1A Strain Amplifiers DPM-900B 3-5 Memory Recorder/Analyzers EDX-3000A 3-79

21 LCH-F High-Accuracy Compression Load Cells Accuracy: 1/00 & 0 kn 2-28 Nonlinearity : Within±0.02% RO Hysteresis : Within±0.02% RO Repeatability : 0.02% RO or less Rated Output : 2 mv/v (00μm/m) ±0.1% Safe Temperature Range : -35 to C Compensated Temperature Range : -10 to C Temperature Effect on Zero Balance : Within ±0.0015% RO/ C Temperature Effect on Output : Within ±0.001%/ C V AC or DC Excitation Voltage : 1 to 10V AC or DC 3Ω±0.5% 3Ω±0.5% Cable : 6-conductor (0.5 mm 2 ) chloroprene shielded cable, 9.5mm diameter by 5m long, with press-fit terminal for 4 mm (Shield wire is not connected to mainframe.) Can Measure Compression Loads with 1/00 Accuracy. Remote sensing possible Watertight structure Useable in high humidity. Safe Overload Rating : 0% Natural Frequency : See table below. See table below. Protection Rating : IP67 (watertight type conforming to JIS C 09) for mount Base C F CA-B A B SR G Mount Base at equal disttance D E 4 M8 d=15 J Press-fit terminal H LCH-10TF LCH-TF kn 0kN Natural Frequency 7.5kHz 7kHz A B (C) φd φe φf G (H) φj SR Weight * Movable Saddle 12kg CA-B 17kg *not including cable Physical quantity indication Static measurement Dynamic measurement LCH-F WGA-6B WGA-6B Data Loggers UCAM-B 3-25 Strain Amplifiers DPM-900 Series 3-5 Universal Recorders EDX-A

22 2-29 LCS-D 5 to kn EXPLPSION PROOF 2G4 Explosion-proof construction Compression Load Cells Dedicated Compression Load Cell of Explosion-Proof Construction. Please contact us for details : See table below Nonlinearity : Within ±0.2%RO Hysteresis : Within ±0.2%RO Repeatability : 0.2% RO or less Rated Output : 2mV/V ( 00μm/m) ±0.2% Safe Temperature Range : -15 to 75 C Compensated Temperature Range : -10 to C Temperature Effect on ZERO Balance : Within ±0.007%RO/ C Temperature Effect on Output : Within ±0.005%/ C Explosion-proof Environmental Conditions : Ambient Temperature : -10 to C Relative Humidity : 45 to 85%RH 15V AC or DC Excitation Voltage : 1 to 10V AC or DC 3Ω±0.5% 3Ω±0.5% Cable : 4-conductor (0.03mm 2 ) chloroprene shielded cable, 5mm diameter by 7.6m long, terminated with connector plug. (Shield wire is not connected to mainframe) Safe Overload Rating : 1% Natural Frequency : See table below See table below Junction Box for Explosion - proof JBS-1C 1 CH JBS-4C 4 CH JBS-1C,4C F SRG JBS-1C JBS-4C 27 4 M8 d= G1/2 91 LCS-0KD LCS-1TD LCS-2TD LCS-5TD Rated Capacity 5kN 10kN kn kn SRG 30 Natural Frequency (Approx) 4kHz 5.3kHz 6.2kHz 6kHz φf Weight (Approx) Lord-bearing Unit 4kg Movable Saddle 4kg CA-10B ER-5B Mounting Base CF- CF- Connector plug 121 Physical quantity indication Static measurement Dynamic measurement 2-29 LCS-D WGA-6B WGA-710C Data Loggers UCAM-B 3-25 Strain Amplifiers DPM-900 Series 3-5 Universal Recorders EDX-A 3-65

23 LC-J Stainless Steel 5 to 0 kn Corrosion-Resistant Compression Load Cells 2-30 Built to order TEDS-installed versions can be manufactured.inquiries are welcome. Suited for Weighing in Food Processing or Where they are Exposed to Corrosive Liquids or Gases. Corrosion-resistant Hermetically-sealed structure with inert gas filled in High overload rating of 0% The hermetically-sealed stainless steel structure with inert gas filled in enables use for weighing in food processing or where they are exposed to corrosive liquids or gases. The high overload rating minimizes the ratio of breakdown due to overload. Nonlinearity : Within±0.5% RO Hysteresis : Within±0.5% RO Repeatability : 0.1% RO or less Rated Output : 1 mv/v (00μm/m) ±0.2% Safe Temperature Range : -35 to C Compensated Temperature Range : -10 to C Temperature Effect on Zero Balance : Within ±0.005% RO/ C Temperature Effect on Output : Within ±0.005%/ C V AC or DC Excitation Voltage : 1 to 12V AC or DC 3Ω±0.5% 3Ω±0.5% Cable : 4-conductor (0.3mm 2 ) chloroprene shielded cable, 7.6 mm diameter by 5 m long, terminated with connector plug (Shield wire is connected to mainframe.) Safe Overload Rating : 0% Natural Frequency : See table below. See table below. A B C SR F D R1/2 G 4 M8 d=12 E 25 Connector plug H LC-0KJ LC-1TJ LC-2TJ LC-5TJ LC-10TJ LC-TJ 5kN 10kN kn kn kn 0kN Natural Frequency 5.2kHz 6kHz 5.8kHz 5.7kHz 5.5kHz 6kHz LC-1TJ/2TJ is provision for movable saddle, please inquires to us. A B C φd φe φf G H SR Weight * 3kg 5kg 6kg *not including cable Physical quantity indication Static measurement Dynamic measurement LC-J WGA-6B Channel Signal Conditioner WGC-1A Data Loggers UCAM-B 3-25 Strain Amplifiers DPM-900 Series 3-5 Memory Recorder/Analyzers EDX-3000A

24 2-31 LCW-C-SA3 Washer-Type Load Cells For Press Forming 10 to 300 kn LCW-C-KN25SA3 LCW-C-300KNSA3 Nonlinearity : Within±1% RO Hysteresis : Within±1% RO Rated Output : Approx. 1 mv/v (00μm/m) Safe Temperature Range : -35 to C Compensated Temperature Range : -10 to C Temperature Effect on Zero Balance : Within±0.01% RO/ C Temperature Effect on Output : Within±0.01%/ C 15V AC or DC Excitation Voltage : 1 to 10V AC or DC 3Ω±1% 3Ω±1% Cable : 4-conductor (0.3 mm 2 ) chloroprene shielded cable, 7.6 mm diameter by 5 m long, bared at the tip (Shield wire is not connected to mainframe.) Thin,High Stability Wide Range of Rated Capacities Extremely simple structure facilitates handling and maintenance. Widely applicable for bolt tension control, press forming, etc M5 d=8 E LCW-C-10,KNSA B A C D B A C F M8 d=12 E 2 D B A C F LCW-C-,KNSA3 R1/2 Safe Overload Rating : 1% See table below. LCW-C-10KN25SA3 LCW-C-10KN35SA3 LCW-C-10KN45SA3 LCW-C-10KN55SA3 LCW-C-10KN65SA3 LCW-C-KN25SA3 LCW-C-KN35SA3 LCW-C-KN45SA3 LCW-C-KN55SA3 LCW-C-KN65SA3 LCW-C-KN30SA3 LCW-C-KNSA3 LCW-C-KNSA3 LCW-C-KNSA3 LCW-C-KNSA3 LCW-C-KNSA3 LCW-C-KN30SA3 LCW-C-KNSA3 LCW-C-KNSA3 LCW-C-KNSA3 LCW-C-KNSA3 LCW-C-KNSA3 LCW-C-0KNSA3 LCW-C-0KNSA3 LCW-C-0KNSA3 LCW-C-0KN90SA3 LCW-C-0KNSA3 LCW-C-300KNSA3 LCW-C-300KNSA3 LCW-C-300KNSA3 LCW-C-300KN90SA3 LCW-C-300KNSA3 Rated Capacity 10kN kn kn kn 0kN 300kN φa φb φc φd φe (F) Weight * 0.6kg 0.7kg 0.8kg 0.9kg 1.0kg 0.6kg 0.7kg 0.8kg 0.9kg 1.0kg 1.7kg 1.9kg 2.1kg 2.3kg 2.5kg 2.7kg 1.7kg 1.9kg 2.1kg 2.3kg 2.5kg 2.7kg 3.7kg 4.1kg 4.4kg 4.8kg 5.1kg 3.7kg 4.1kg 4.4kg 4.8kg 5.1kg *not including cable R1/2 D 4 M8 d=12 E F Bared at the tip Physical quantity indication 2-31 LCW-C-0,300KNSA3 LCW-C-SA WGA-6B Channel Signal Conditioner WGC-1A 2-173

25 H H LCW-D-S/E-S Washer-Type Load Cells For Rolling/Depressing Pressure Measurement under Harsh Envrionment 1 to 5 MN 2-32 LCW-D-S LCW-E-S Load cells which meet individual rolling mills can also be manufactured. Inquiries are welcome. Nonlinearity : Within±1% RO Hysteresis : Within±1% RO Repeatability : 0.3% RO or less Rated Output : 1 mv/v (00μm/m) or more Safe Temperature Range : - to C Compensated Temperature Range : -10 to C Temperature Effect on Zero Balance : Within ±0.01% RO/ C Temperature Effect on Output : Within ±0.01%/ C 15V AC or DC Excitation Voltage : 1 to 10V AC or DC 3Ω±1% 3Ω±1% Cable : 4-conductor (0.75mm 2 ) fluonlex shielded cable, 8 mm diameter by 15 m long, bared at the tip (Shield wire is not connected to mainframe.) The Flat Washer-Type Structure of Loadcell Well Suited to Rolling Mills. Hermetically-sealed structure with inert gas filled in Heat and oil resistant cable. High reliability The hermetically-sealed structure with inert gas filled in ensures a reliable and stable operation under harsh conditions. The flat washer type structure only requires processing of the screw nuts for installation to existing rolling mills. Safe Overload Rating : 1% Natural Frequency : See table below. See table below. Protection Rating : IP64 (Splashproof type conforming to JIS C 09) A B C D C B (34) 3 3 (Outer diameter of cable outlet tube) A B C D C B 3 3 J (25) E E 2 F 2 G H=10 LCW-D-S 2 F 2 G H=10 K LCW-E-S Bared at the tip LCW-D-1MNS LCW-D-2MNS LCW-D-3MNS LCW-D-5MNS LCW-E-1MNS LCW-E-2MNS LCW-E-3MNS LCW-E-5MNS Natural Frequency 1MN 2MN 3MN 5MN 1MN 2MN 3MN 5MN 16kHz 14kHz 15kHz 16kHz 16kHz 14kHz 15kHz 16kHz φa φb φc φd φe F φg H J K Physical quantity indication M8 d=8 M10 d=10 M10 d=12 M10 d=12 M8 d=8 M10 d=10 M10 d=12 M10 d= Weight * 7kg 15kg 17kg kg 7kg 15kg 17kg kg *not including cable LCW-D-S/E-S WGA-6B WGA-6B Channel Signal Conditioner WGC-1A

26 2-33 LCTS-B Stainless Steel Load Cells Stainless Steel 5 to kn TEDS-installed versions can be manufactured.inquiries are welcome. Developed for Weighing Hoppers and Tanks, LCTS-B Series is a Stainless Steel Compression Load Cells with Built-In Steady Brace Mechanism. Nonlinearity : Within±0.05% RO Hysteresis : Within±0.05% RO Repeatability : 0.02% RO or less Rated Output : 2 mv/v (00μm/m) ±0.1% Safe Temperature Range : - to C Compensated Temperature Range : -10 to C Temperature Effect on Zero Balance : Within±0.003% RO/ C Temperature Effect on Output : Within±0.003%/ C V AC or DC Excitation Voltage : 1 to 10V AC or DC 0Ω±0.7% 0Ω±0.7% Cable : 4-conductor (0.3 mm 2 ) chloroprene shielded cable, 7.6 mm diameter by 5 m long (10 m long with and KN), bared at the tip (Shield wire is not connecte to mainframe) Safe Overload Rating : 1% Critical Lateral Load : 10 kn (30 kn with and KN) (Maximum load which does not cause any mechanical damage) See table below. Material : Stainless steel alloy Protection Rating : IP67 (Watertight type conforming to JIS C 09) Stainless steel structure enables use under conditions where the load cell is exposed to moisture and corrosive gases. "Thin" and "Top and Bottom plates integrated" design facilitates installation to hopper brackets or tank's feet. Hermetically-sealed structure (protection rating IP67) Built-in steady brace mechanism makes LCTS-B suitable for weighing stirring tanks or tanks with feet, while simplifying peripheral facilities by eliminating check rod, etc. Since the load cell can be fixed with bolts, dropping or floating of the load cell can be prevented. LCTS-B-5KN LCTS-B-10KN LCTS-B-KN LCTS-B-30KN LCTS-B-KN LCTS-B-KN 5kN 10kN kn 30kN kn kn To Ensure Safe Usage Weight * 5kg 6kg 11kg 13kg *not including cable Accessories to Load Cell Do not disassemble or remodel accessories such as top plate and mounting plate designed for installation of LCTS-B series load cells. Installation of Floating Prevention Stopper Install the hazard prevention stopper when using in an environment where the load cell may be damaged or the hopper or tank may overturn due to lateral load or lateral displacement caused by thermal expansion of structure or vibration of stirrer. Precautions 1. LCTS-B cannot be used for any onboard measurement. 2. LCTS-B cannot be used in an environment where it is frequently exposed to lateral load. 3. LCTS-B cannot be installed to any inclined or vertical surface. 2-33

27 R1/ (12) (30kN 61.5) R1/ (19) 0 12 L 87 (kn 95) 112 LCTS-B-5 to 30KN 1 LCTS-B- & KN Bared at the tip Installation Examples Internal Structure Diaphragm Guide bolt Load Button Top plate Cable shroud Mounting bolt Load cell mounting plate Jack Installation to Tank's Brackets Load cell Tabe taper screw Mounting plate Center rubber Load button Load Guide bolt Guide bolt to prevent floating Center rubber Installation to Tank's Feet Mechanical stopper(steady brace):patent pending Physical quantity indication Static measurement Dynamic measurement LCTS-B WGA-6B WGA-6B Channel Signal Conditioner WGC-1A Data Loggers UCAM-B 3-25 Universal Recorders EDX-A

28 2-35 LCTA-A Thin Load Cells "Multi Force Sensors" Thin 0 N to 3 kn TEDS-installed versions can be manufactured. Inquiries are welcome. Advanced Thin Design. Compared to the Conventional Load Cell, the Height is 1/2 to 1/3 Enabling a Wider Range of Applications. Original ideas and advanced technologies cultivated in weight control of large scale airplanes made the revolutionary thin design of the LCTA-A series load cells possible. The integrated design and rubber attachment enable use with the top and bottom fixed and provide excellent buffer. Optional dedicated rubber attachment enables fixing the top and bottom with bolts, thereby making it possible to design the system with no tension rod or stay rod used. Safety factor is 3 to 5 times higher than conventional type. Endures lateral loads up to % of the rated capacity. Rubber attachment attenuates impact energy and lessens the effects of thermal expansion of system and the moment of fixed section. Rubber attachement enables easy installation without concern for parallelism. Varieties of accuracies and outputs are available, enabling configuration of the most suitable system for each application. Peripheral instruments such as amplifiers can easily be connected since the wirings are the same as conventional load cells. Nonlinearity : Within ±0.05% RO Hysteresis : Within ±0.05% RO Repeatability : 0.03% RO or less Rated Output : 2 mv/v (00μm/m) ±0.2% Safe Temperature Range : - to C Compensated Temperature Range : -10 to C Temperature Effect on Zero Balance : Within±0.01% RO/ C Temperature Effect on Output : Within±0.01%/ C V DC Excitation Voltage : 1 to 10V DC 3Ω±1.5% 3Ω±1.5% Dedicated connection cable : HW005-AD Included cable : 4-conductor (0.5 mm 2 ) shielded vinyl sheath, 8.5mm diameter by 5m long, bared at the tip (Shield wire is not connected to mainframe) Safe Overload Rating : 1% Critical Lateral Load : % (maximum load which does not cause any mechanical damage) Approx. 1.1kg (not including cable) Material : Aluminum alloy Precautions 1. LCTA-A cannot be used for any onboard measurement. 2. LCTA-A cannot be used in an environment where it is frequently exposed to lateral load. 3. LCTA-A cannot be installed to any inclined or vertical surface. 4 M8 Depth (16) Bared at the tip LCTA-A-0N LCTA-A-0N LCTA-A-1KN LCTA-A-2KN LCTA-A-3KN (55) A10-7M (Included cable HW005-BZ: length 5m) (35) 0N 0N 1kN 2kN 3kN 4 9, 14 depth of counter bore d=9 2-35

29 2-36 Accessories Stainless steel cover Applicable Accessories Frame Rubber attachment Rubber attachment Accessories Sensor Stainless Steel Cover Rubber Attachment LCTA-A-0N LCTA-A-0N LCTA-A-1KN LCTA-A-2KN LCTA-A-3KN COV03-300K RA02-K RA02-300K 4 9 A drilled through t= M8 screw (Effective screw length: ) Rigid urethane Weight: Approx. 1 g 7 Weight: Approx. 0 g Stainless Steel Cover Rubber Attachment RA02-K RA02-300K φa Physical quantity indication Static measurement Dynamic measurement LCTA-A WGA-6B WGA-6B Channel Signal Conditioner WGC-1A Data Loggers UCAM-B 3-25 Universal Recorders EDX-A

30 2-37 LCTB-A Thin Load Cells "Multi Force Sensors" Thin 5 to kn TEDS-installed versions can be manufactured.inquiries are welcome. Advanced Thin Design. Compared to the Conventional Load Cell, the Height is 1/2 to 1/3 Enabling a Wider Range of Applications. Optional dedicated rubber attachment enables fixing the top and bottom with bolts, thereby making it possible to design the system with no tension rod or stay rod used. Safety factor is 3 to 5 times higher than conventional type. Endures lateral loads up to % of the rated capacity. Rubber attachment attenuates impact energy and lessens the effects of thermal expansion of system and the moment of fixed section. Rubber attachement enables easy installation without concern for parallelism. Varieties of accuracies and outputs are available, enabling configuration of the most suitable system for each application. Peripheral instruments such as amplifiers can easily be connected since the wirings are the same as conventional load cells. Nonlinearity : Within±0.03% RO Hysteresis : Within±0.03% RO Repeatability : 0.02% RO or less Rated Output : 1.5 mv/v (3000μm/m) ±0.2% Safe Temperature Range : - to C Compensated Temperature Range : -10 to C Temperature Effect on Zero Balance : Within±0.005% RO/ C Temperature Effect on Output : Within±0.005%/ C V DC Excitation Voltage : 1 to 10V DC 3Ω±1.5% 3Ω±1.5% Cable : 4-conductor (0.3mm 2 ) chloroprene shielded cable, 6 mm diameter by 5 m long, bared at the tip Safe Overload Rating : 1% Critical Lateral Load : % (maximum load which does not cause any mechanical damage) See table below. Material : Aluminum alloy Precautions 1. LCTB-A cannot be used for any onboard measurement. 2. LCTB-A cannot be used in an environment where it is frequently exposed to lateral load. 3. LCTB-A cannot be installed to any inclined or vertical surface. name for instrinsic safety construction is "M4AL2". H B D F A C E G (Q) L N M J 4 K d=12 P Bared at the tip 2-37 LCTB-A-5KN LCTB-A-10KN LCTB-A-KN LCTB-A-30KN LCTB-A-KN Rated Capacity 5kN 10kN kn 30kN kn A B C D E F G H φj K L φm φn P (Q) M8 M Weight * kg 2.3kg kg kg *not including cable

31 Accessories Frame 2-38 Rubber attachment Stainless steel cover Sensor Accessories with base plate Base plate Applicable Accessories LCTB-A-5KN LCTB-A-10KN LCTB-A-KN LCTB-A-30KN LCTB-A-KN Accessories with stainless steel cover Stainless Steel Cover Rubber Attachment Base Plate COV01-2T RA01-2T BP01-2T RA01-5T Counter bore 4-flush bolf(g) ( F) Stainless Steel Cover COV01-2T COV01-5T A B C D E (φf) G Weight M8 0g M10 900g Base plate 4 K H 4 J B E G B E D C A C F D A Load Cells LCTB-A-5KN LCTB-A-10KN LCTB-A-KN Base plate BP01-2T A B C D E F G φh φj K M10 Physical quantity indication Static measurement Dynamic measurement LCTB-A WGA-6B WGA-6B Channel Signal Conditioner WGC-1A Data Loggers UCAM-B 3-25 Universal Recorders EDX-A

32 2-39 LCTE-A Thin Load Cells "Multi Force Sensors" Thin 10 to kn TEDS-installed versions can be manufactured.inquiries are welcome. Nonlinearity : Within±0.05% RO (0.1% RO with KN) Hysteresis : Within±0.05% RO (0.1% RO with KN) Repeatability : 0.03% RO (±0.05% RO with KN) or less Rated Output : 2 mv/v (00μm/m) ±0.2% Safe Temperature Range : - to C Compensated Temperature Range : -10 to C Temperature Effect on Zero Balance : Within±0.003% RO/ C Temperature Effect on Output : Within±0.003%/ C V DC Excitation Voltage : 1 to 10V DC 3Ω±1.5% 3Ω±1.5% Cable : 4-conductor (0.3mm 2 ) chloroprene shielded cable, 6 mm diameter by 5 m long (10 m long withkn), bared at the tip (Shield wire is not connected to mainframe) Advanced Thin Design. Compared to the Conventional Load Cell, the Height is 1/2 to 1/3 Enabling a Wider Range of Applications. Optional dedicated rubber attachment enables fixing the top and bottom with bolts, thereby making it possible to design the system with no tension rod or stay rod used. Safety factor is 3 to 5 times higher than conventional type. Endures lateral loads up to % of the rated capacity. Rubber attachment attenuates impact energy and lessens the effects of thermal expansion of system and the moment of fixed section. Rubber attachement enables easy installation without concern for parallelism. Varieties of accuracies and outputs are available, enabling configuration of the most suitable system for each application. Peripheral instruments such as amplifiers can easily be connected since the wirings are the same as conventional load cells. Safe Overload Rating : 1% Critical Lateral Load : % (maximum load which does not cause any mechanical damage) See table below. Material : Special steel Precautions 1. LCTE-A cannot be used for any onboard measurement. 2. LCTE-A cannot be used in an environment where it is frequently exposed to lateral load. 3. LCTE-A cannot be installed to any inclined or vertical surface. C D A E G K J F (H) L B Bared at the tip 2-39 LCTE-A-10KN LCTE-A-KN LCTE-A-30KN LCTE-A-KN LCTE-A-KN Rated Capacity 10kN kn 30kN kn kn φa B C φd φe F G (H) φj φk L Weight * kg 5.1kg kg kg *not including cable

33 2- Accessories Frame Rubber attachment Sensor Applicable Accessories LCTE-A-10KN LCTE-A-KN LCTE-A-30KN LCTE-A-KN LCTE-A-KN Rubber Attachment RA01-2T RA01-5T RA01-5T, RA01-10T Physical quantity indication Static measurement Dynamic measurement LCTE-A WGA-6B WGA-6B Channel Signal Conditioner WGC-1A Data Loggers UCAM-B 3-25 Universal Recorders EDX-A

34 2-41 LCTD-A Thin Load Cells "Multi Force Sensors" Thin to 300 kn TEDS-installed versions can be manufactured.inquiries are welcome. Advanced Thin Design. Compared to the Conventional Load Cell, the Height is 1/2 to 1/3 Enabling a Wider Range of Applications. Optional dedicated rubber attachment enables fixing the top and bottom with bolts, thereby making it possible to design the system with no tension rod or stay rod used. Safet y fac tor is 3 to 5 times higher than conventional type. Endures lateral loads up to % of the rated capacity. Rubber attachment attenuates impact energy and lessens the effects of thermal expansion of system and the moment of fixed section. Rubber attachement enables easy installation without concern for parallelism. Varieties of accuracies and outputs are available, enabling configuration of the most suitable system for each application. Peripheral instruments such as amplifiers can easily be connected since the wirings are the same as conventional load cells. Nonlinearity : Within±0.03% RO Hysteresis : Within±0.03% RO Repeatability : 0.02% RO or less Rated Output : 2 mv/v (00μm/m) ±0.2% Safe Temperature Range : - to C Compensated Temperature Range : -10 to C Temperature Effect on Zero Balance : Within±0.003% RO/ C Temperature Effect on Output : Within±0.003%/ C V DC Excitation Voltage : 1 to 10V DC 3Ω±1.5% 3Ω±1.5% Cable : 4-conductor (0.3 mm 2 ) chloroprene shielded cable, 7.6 mm diameter by 10 m long, bared at the tip (Shield wire is not connected to mainframe) Safe Overload Rating : 1% Critical Lateral Load : % (maximum load which does not cause any mechanical damage) See table below. Material : Special steel Precautions 1.LCTD-A cannot be used for any onboard measurement. 2.LCTD-A cannot be used in an environment where it is frequently exposed to lateral load. 3. LCTD-A cannot be installed to any inclined or vertical surface. Accessories Rubber attachment Frame 4 Q d=r Sensor B E G H F D A For rubber attachment and base plate, refer to page Bared at the tip N C K J Applicable Accessories Rubber Attachment 2.5 M L LCTD-A-KN LCTD-A-0KN LCTD-A-300KN RA01-10T RA01-30T P LCTD-A-KN LCTD-A-0KN LCTD-A-300KN Rated Capacity kn 0kN 300kN Weight A B C D E F G H J K φl φm N φp Q R * kg M kg M kg *not including cable Physical quantity indication Static measurement Dynamic measurement 2-41 LCTD-A WGA-6B WGA-6B Channel Signal Conditioner WGC-1A Data Loggers UCAM-B 3-25 Universal Recorders EDX-A 3-65

35 2-42 Accessories Rubber Attachments Grounding Conductors for Weighing Sensors A C Length B D 4 E JA3-0 JA3-0 0 mm 0 mm J G A B C D φe φf G H J φk L Weight H K F L Ridid urethane RA01-2T RA01-5T RA01-10T RA01-30T kg 3.2kg 7.4kg 19.2kg 4-channel Junction Box:JB4LC-US Note: Adjustment through calibration with actual load is required. 4 7 (30) 6 M4 small pan-head screw 144 (30) (10) Applicable wire tube( 6 9) (16) (30) Applicable wire tube( )

36 2-43 LTZ-A High-Accuracy Tension Load Cells Small-Sized, High-Accuracy 0 N to kn LTZ-~KA LTZ-0KA~2TA Nonlinearity : Within±0.03% RO (LTZ-KA to 0KA) Within ±0.05% RO (LTZ-0KA to 5TA) Hysteresis : Within±0.03% RO (LTZ-KA to 0KA) Within ±0.05% RO (LTZ-0KA to 5TA) Repeatability : 0.03% RO or less Rated Output : 3 mv/v (00μm/m) ±0.2% Safe Temperature Range : - to C Compensated Temperature Range : -10 to C Temperature Effect on Zero Balance : Within±0.005% RO/ C Temperature Effect on Output : Within±0.005%/ C V AC or DC Excitation Voltage : 1 to 10V AC or DC 3Ω±0.5% 3Ω±0.5% Cable : 4-conductor (0.5 mm 2 ) chloroprene shielded cable, 8.5mm diameter by 3m long, with press-fit terminal for 4mm (Shield wire is not connected to mainframe.) Safe Overload Rating : 1% Material : Aluminum alloy (mainframe of to 0KA) Natural Frequency : See table below. See table below. Protection Rating : IP64 (Splashproof type conforming to JIS C 09) LTZ-5TA TEDS-installed versions can be manufactured. Inquiries are welcome. Usable also for compression load measurement (Extra calibration and patch are required.) LTZ-KA LTZ-KA LTZ-0KA LTZ-0KA LTZ-1TA LTZ-2TA LTZ-5TA 0N 1kN 2kN 5kN 10kN kn kn Natural Frequency 1.25kHz 1.75kHz 2kHz 2.5kHz 2.8kHz 2.6kHz 4.3kHz Weight * 300g 3g 0g 1.5kg 4.4kg *not including cable Bared at the tip Pressure bonded terminal Nonlinearity : within±0.05%ro In Combination with Ball Joint Compact and lightweight Large output Usable also for compression load measurement (Extra calibration and patch are required.) The LTZ-A series load cells adopt a Roberval's mechanism to ensure 1/3333 nonlinearity and easy handling and maintenance. Since they can be installed with less burden to existing facilities, they are used as compact, lightweight load cells with excellent cost performance for weighing or testing systems in various fields. (Patented) Note: Not usable for special accessorles for tansion loads except ball joint. Physical quantity indication Static measurement Dynamic measurement 2-43 LTZ-A WGA-6B Data Loggers UCAM-B 3-25 Strain Amplifiers DPM-900 Series 3-5 Universal Recorders EDX-A 3-65 Memory Recorder/Analyzers EDX-3000A 3-79

37 D (23) 1 (65) 2-44 E F () 2 G 2 H 2 M24P 2 d= LTZ-KA LTZ-KA LTZ-0KA LTZ-0KA LTZ-1TA LTZ-2TA LTZ-5TA B C C ( 12) (19) LTZ-KA~2TA LTZ-5TA A B C φd E F G φh M6 P=1 d= M12 P=1.75 d=18 M18 P=1.5 d= See the above dimensional drawing. Bared at the tip Pressure bonded terminal When not loaded Strain gage When loaded F Tension load measurement Fixed portion Compression load measurement Cable Loaded portion W Load cell Drop prevention fixture F W Loaded portion Fixed portion Stopper Principle Standard Installation Example of Drop Prevention in Combination with Special Accessories In Combination with Patch CWM Contact us for using the tension load cell in with special accessories. 2 D R C 1 B E 1 Load Cell LTZ-KA LTZ-KA LTZ-0KA LTZ-0KA LTZ-1TA LTZ-2TA LTZ-5TA 2Patch B C φd E R CWM-6 CWM-12 CWM-18 CWM M6 P=1 M12 P=1.75 M18 P=1.5 M24 P= SR30 SR30 SR

38 in Combination with Special Accessories 2-45 In Combination with Patch CWM, Mount Base CF and Saddle CA L M 4 N at equal distance 1Load Cell LTZ-KA LTZ-KA LTZ-0KA LTZ-0KA LTZ-1TA LTZ-2TA LTZ-5TA CWM-6 CWM-12 CWM-18 CWM-24 CA-2B CA-2B CA-2B CA-10B In Combination with Patch CWM, Mount Base CF and Movable Saddle ER 2 Patch 3Mount Base φl φm φn Q R 4 S at equal distance 1Load Cell LTZ-KA LTZ-KA LTZ-0KA LTZ-0KA LTZ-1TA LTZ-2TA LTZ-5TA 2Patch 3Movable Saddle φq φr S CWM-6 CWM-12 CWM-18 CWM-24 ER-2B ER-2B ER-2B ER-5B M8 M8 M8 M12 In Combination with Ball Joint TU Note:Ball joint(tu) should be mounted to load cell at our factory. F E A (approx.) B (approx.) C 1 4 G 3 D 2 1Load Cell LTZ-KA LTZ-KA LTZ-0KA LTZ-0KA LTZ-1TA LTZ-2TA LTZ-5TA 2Ball Joint TU-6C TU-12C TU-18C TU-24C 3Hexagon NutHexagon Nut M6 P=1 M12 P=1.75 M18 P=1.5 M24 P=2 4Spring Washer A B C φd φe F G 2# 6S 2# 12S 2# 18S 3# 24S M6 P=1 M12 P=1.75 M18 P=1.5 M24 P=2 Static Breaking Load 1.4kN 2.9kN 5.8kN 14.7kN 29.4kN 58.8kN 147kN Dimensions A and B are approximate, since the ball joint is screw-in type. 2-45

39 LT-FH/FL High-temperature High/Low Temp. Tension Load Cells -10 to 1 C Low-temperature -196 to 30 C 0N to kn 2-46 TEDS-installed versions can be manufactured. Inquiries are welcome. High Reliability, Airtight Structure, Selectable from a Wide Range of Rated Capacities. Mechanical stopper that activates at 0% overload : See table below Nonlinearity : Within ±0.5%RO Hysteresis : Within ±0.5%RO Repeatability : 0.05% RO or less Rated Output : 1.5mV/V ( 3000μm/m) ±0.2% Safe Temperature Range : FH : -10 to 1 C (Excluding connector part) FL : -0 to C (Excluding connector part) Compensated Temperature Range: FH : -10 to 1 C (Excluding connector part) FL : -196 to 30 C (Excluding connector part) Temperature Effect on ZERO Balance : Within ±0.005%RO/ C Temperature Effect on Output : Within ±0.01%/ C V AC or DC Excitation Voltage : 1 to 10V AC or DC 3Ω±0.5% 3Ω±0.5% Cable : 4-conductor (0.03mm 2 ) fluoroplastic shielded cable, 5mm diameter by 5m long, terminated with connector plug. (Shield wire is not connected to mainframe) Safe Overload Rating : 0% Critical Overload : 0% Natural Frequency : See table below See table below LT-FH series enables continuous operation under temperature as high as 1 C with no external cooling. LT-FL series enable operation at ultra-low temperatures ranging from -196 C. (FH) LT-KFH LT-KFH LT-0KFH LT-0KFH LT-1TFH LT-2TFH LT-5TFH (FL) LT-KFL LT-KFL LT-0KFL LT-0KFL LT-1TFL LT-2TFL LT-5TFL 0N 1kN 2kN 5kN 10kN kn kn Natural Frequency 1.5kHz 2.6kHz 4.1kHz 5.0kHz 5.2kHz 5.8kHz 4.5kHz Weight * 1.7kg 2.0kg 2.1kg 2.4kg 7.0kg *not including cable F G H A E (B) C G D H F R1/2 J LT-KFH LT-KFL LT-KFH LT-KFL LT-0KFH LT-0KFL LT-0KFH LT-0KFL LT-1TFH LT-1TFL LT-2TFH LT-2TFL LT-5TFH LT-5TFL A (B) C φd E F G H M12 P=1.75 M14 P=2 M18 P=1.5 M24 P=2 M39 P= J Connector plug Physical quantity indication Static measurement Dynamic measurement LT-FH/FL WGA-6B WGA-6B Data Loggers UCAM-B 3-25 Strain Amplifiers DPM-900 Series 3-5 Universal Recorders EDX-A

40 2-47 LUX-B-ID Compact Tension/Compression Load Cells Compact N to kn Note: For transducers providing both positive and negative outputs, an average of both outputs are written as the rated output. Suitable for Measuring and Controlling Loads Applied to Small-Scale Presses and Press-Fitting Devices High sensitivity Waterproof connector Stainless steel Easy installation Compact and lightweight design with a screw-shape load receiving portion facilitates easy installation to equipment. Furthermore, the cable is connected using a connector, therefore there are no problems with wiring when situating, and cable replacement is easy. Work is also possible if the cable is replaced with one resistant to repeated bending (flexible cable). Please add M1Z3K to the end of the model name. : See table below Nonlinearity: Within ±0.15% RO (LUX-B-N to 2KN) Within ±0.1% RO (LUX-B-5KN to KN) Hysteresis : Within ±0.15% RO (LUX-B-N to 2KN) Within ±0.1% RO (LUX-B-5KN to KN) Repeatability : 0.05% RO or less Rated Output : ±0.85mV/V (±10μm/m) or more (LUX-B-) ±0.9mV/V (±10μm/m) or more (LUX-B-N to 1KN) ±1.3mV/V (±1900μm/m) or more (LUX-B-2KN to KN) Safe Temperature Range : - to C Compensated Temperature Range : -10 to C Temperature Effect on Zero Balance : Within ±0.03% RO/ C (LUX-B-N to 0N) Within ±0.005% RO/ C (LUX-B-0N to KN) Temperature Effect on Output : Within ±0.005%/ C 10V AC or DC (LUX-B-N to 0N) 15V AC or DC (LUX-B-0N to KN) Excitation Voltage : 1to 5V AC or DC (LUX-B-N to 0N) 1to 10V AC or DC (LUX-B-0N to KN) 375Ω±1.5% 3Ω±1% Dedicated connection cable : TE-45 Included cable : 4-conductor (0.08mm 2 ) chloroprene shielded cable, 4mm diameter by 3m long, with connector plug to mainframe side, and bared to amplifier side (Shield wire is not connected to mainframe) Safe Overload Rating : 1% Natural Frequency : See table below Material : SUS (metallic finish) Approx. 2g (5 to KN) Approx. 90g (0 to 2KN) Approx. g (0N or less) (not including cable) Protection Rating : IP67 (Watertight type conforming to JIS 09) LUX-B-N-ID LUX-B-N-ID LUX-B-0N-ID LUX-B-0N-ID LUX-B-1KN-ID LUX-B-2KN-ID LUX-B-5KN-ID LUX-B-10KN-ID LUX-B-KN-ID ±N ±N ±0N ±0N ±1kN ±2kN ±5kN ±10kN ±kn Natural Frequency Tightening Torque (N.m) 8kHz 11kHz 3N m 14kHz 16kHz 21kHz 10N m 27kHz 18kHz 21kHz N m 25kHz Bared at the tip (for TEDS installation) To Ensure Safe Usage If impacts are expected in receiving tension loads, select a load cell with the rated capacity higher by one rank than the operating load. Physical quantity indication Static measurement Dynamic measurement 2-47 LUX-B-ID WGA-6B Data Loggers UCAM-B 3-25 Strain Amplifiers DPM-900 Series 3-5 Universal Recorders EDX-A 3-65 Memory Recorder/Analyzers EDX-3000A 3-79

41 M4 SR10 Thin nut SUS SR30 M (7) (10) (38) (41) (38) 28 (43) 22 Standard cable(te-45) 2 3 d=2 (95) Minimum mounting dimensions when bending the cable LUX-B-~0N-ID M Thin nut SUS 18 M4 D=4 SR30 (C) M6 d=7 (95) Minimum mounting dimensions when bending the cable LUX-B-0N~2KN-ID d=2 D (B) A (38) 43 (58) M d=12 33 LUX-B-5KN-ID LUX-B-10KN-ID LUX-B-KN-ID A B C D () Minimum mounting dimensions when bending the cable 2 5 d=3 Bared at the tip LUX-B-5~KN-ID of Mount Base Mount Base CX 2 M H through hole D 30 3 J through hole at equal distance E F B L C A R1 N G Load Cell LUX-B-N-ID LUX-B-N-ID LUX-B-0N-ID LUX-B-0N-ID LUX-B-1KN-ID LUX-B-2KN-ID LUX-B-5KN-ID LUX-B-10KN-ID LUX-B-KN-ID Mount Base φa φb φc φd E F G φh φj L φm Weight N CX-2 CX-4 CX ±0.1 21±0.1 33± g g 3g Hexagon socket head bolt for connection between load cell and mount base and locking pins are attached to the mount base. 2-48

42 in Combination with Special Accessories 2-49 In Combination with Mount Base CX The patch should be prepared by user or CA-2F or the equivalent should be used. This does not apply to tension load measurement. Patch Load cell Hex. socket head bolt (Mount base accessory) Load cell LUX-B-N-ID LUX-B-N-ID LUX-B-0N-ID LUX-B-0N-ID LUX-B-1KN-ID LUX-B-2KN-ID LUX-B-5KN-ID LUX-B-10KN-ID LUX-B-KN-ID In Combination with Ball Joint TU, Whirl-Stop Coupling TSC and Whirl-Stop Bracket TS This does not apply to compression load measurement. A Locking pin (Mount base accessory) Mount base B F Mount Base CX-2 CX-4 CX-6 (A) (B) Ball joint TU Split pin Whirl-stop coupling (TSC-M) Outside screw stopper bolt (B) (A) Whirl-stop bracket (TS) Thin nut (Load cell accessory) Load cell Whirl-stop coupling (TSC-F) Stripper bolt Note that the Whirl-Stop Bracket TS is not a safety device to be used when a load exceeding the safe overload is applied. If exceeding safe overload is applied, install a safety device on customer side before use. Split pin E D C Ball joint TU Load Cell LUX-B-N-ID LUX-B-N-ID LUX-B-0N-ID LUX-B-0N-ID LUX-B-1KN-ID LUX-B-2KN-ID LUX-B-5KN-ID LUX-B-10KN-ID LUX-B-KN-ID Whirl-stop Coupling Whirl-stop Bracket Ball Joint TSC-2M TSC-2F TSC-4MB TSC-4FB TSC-6MB TSC-6FB TS-2 TS-4B TS-6B TU-6B TU-12B TU-18B (A) (B) C D φe F To Ensure Safe Usage Check the strength of the material to which the load cell is tightened. If a load cell with the rated capacity of 2 kn or more is selected, the material to which the load cell is tightened should have a tensile strength σb of 0 : N/mm 2 or higher. Typical recommended materials : SUS630(H900) HRC to 47 SCM435 HRC30 to 38 For tension load measurement, take care never to exceed the safe overload rating. 2-49

43 LUX-B Safe Bending Moment (N.mm) Figures below show the safe bending moment against lateral load with a load applied in sensitivity direction (vertical direction) M : Safe bending moment load (N mm) M f L F : Load in sensitivity direction(n) F : Safe lateral load(n) Mount center Safe Bending Moment (N mm) :N Safe Bending Moment (N mm) :N L LUX-B-~0N M : Safe bending moment load (N mm) M f L F : Load in sensitivity direction(n) F : Safe lateral load(n) Mount center Safe Bending Moment (N mm) Safe Bending Moment (N mm) :1KN Load in Sensitivity direction (% RO) Load in Sensitivity direction (% RO) Load in Sensitivity direction (% RO) Safe Bending Moment (N mm) Safe Bending Moment (N mm) Load in Sensitivity direction (% RO) Load in Sensitivity direction (% RO) Safe Bending Moment (N mm) Load in Sensitivity direction (% RO) F : 0N ( RO) f 17 Load in Sensitivity direction (% RO) :0N Load in Sensitivity direction (% RO) :0N Safe Bending Moment (N mm) Load in Sensitivity direction (% RO) L :2KN LUX-B-0N~2KN 15 Safe Bending Moment (N mm) M : Safe bending moment load (N mm) M f L F : Load in sensitivity direction(n) F : Safe lateral load(n) Mount center LUX-B-5~KN L :5KN :KN :10KN How to Obtain Safe Lateral Load Shown here is an example calculating the safe lateral load when the LUX-B-1KN receives a load in sensitivity direction (vertical direction). (See Fig. 1.) The safe lateral load f (N) which can be applied to the screw at the distance of 17 mm from the center of moment when a load of 0 N (% the rated capacity) is applied in sensitivity direction and is obtained as follows: According to Graph-1, safe bending moment, M, is approximately N m when a load of % the rated capacity is applied in sensitivity direction. Since the relation between safe lateral load f, and safe bending moment M is M = f L, M f = = L 17 =147.1N Therefore, the safe lateral load f is N. Safe Bending Moment(N mm) fig:1 15 :1KN Load in Sensitivity direction (% RO) Graph-1 2-

44 2-51 LUR-A-SA1 Compact Tension/Compression Load Cells 28mmφ, Weight g N to 2kN Compact, Lightweight Tension/Compression Load Cells Compact and lightweight LUR-A-S1 series is easy to use tension/compression load cells, which can be used in various fields ranging from production lines to experiments. To Ensure Safe Usage Consult with our sales engineer when using in with special accessories. Special accessories for tension loads should be mounted to the load cell at our factory. When using for tension loads, be sure to fix the load cell with accessory hexagon socket head setscrews (M3 L=4). Note : The connector plug at the cable tip may be replaced with R05-PB5M, when ordering, Sutfix -R to the model number. Nonlinearity : Within±0.5% RO Hysteresis : Within±0.5% RO Rated Output : ±0.5 mv/v (±0μm/m) or more (LUR-A-NSA1 to 2KNSA1) Approx. ±0.4 mv/v (±0μm/m) (LUR-A-NSA1) Safe Temperature Range : -10 to C Compensated Temperature Range : 0 to C Temperature Effect on Zero Balance : Within±0.05% RO/ C (LUR-A-NSA1 to 2KNSA1) Within±0.1% RO/ C (LUR-A-NSA1) Temperature Effect on Output : Within±0.05%/ C (LUR-A-NSA1 to 2KNSA1) Within±0.1% / C (LUR-A-NSA1) 7V AC or DC Excitation Voltage : 1 to 2V AC or DC 3Ω±2% 3Ω±2% Cable : 4-conductor (0.05 mm 2 ) chloroprene shielded cable, 3 mm diameter by 5 m long, terminated with NDIS connector plug Safe Overload Rating : 1% Natural Frequency : See table below. Approx. g (not including cable) Standard Accessories Hexagon socket head setscrew M3 L=4 LUR-A-NSA1 LUR-A-NSA1 LUR-A-0NSA1 LUR-A-0NSA1 LUR-A-1KNSA1 LUR-A-2KNSA1 ±N ±N ±0N ±0N ±1kN ±2kN Natural Frequency 2kHz 4kHz 5kHz 9kHz 14kHz khz in Combination with Ball Joint 2 M8 P 1.25 d=8 12 In Combination with Ball Joint TU-8 Ball Joint TU M3(for setscrew) Hexagon socket head setscrew 5 ( 7) 8 12 (15) (111) Connector plug 28 Physical quantity indication Static measurement Dynamic measurement 2-51 LUR-A-SA1 WGA-6B Data Loggers UCAM-B 3-25 Strain Amplifiers DPM-900 Series 3-5 Memory Recorder/Analyzers EDX-3000A 3-79

45 LU-E Tension/Compression Load Cells TEDS-installed versions can be manufactured. Inquiries are welcome. A B 4 E H G G J SR F D (K) R1/2 () Tension/Compression Load Cells 0N to 0kN Hermetically-Seal Structure With Inert Gas Filled in Usable for both Tension and Compression Loads The detection portion is hermetically sealed with inert gas filled in to prevent aging deterioration and to ensure reliability and stability for a long period of time. Nonlinearity : Within±0.2% RO Hysteresis : Within±0.1% RO Repeatability : 0.1% RO or less Rated Output : 2 mv/v (00μm/m) ±0.2% Safe Temperature Range : -30 to 85 C Compensated Temperature Range : -10 to C Temperature Effect on Zero Balance : Within±0.005% RO/ C Temperature Effect on Output : Within±0.005%/ C V AC or DC Excitation Voltage : 1 to 10V AC or DC 3Ω±0.5% 3Ω±0.5% Cable : 4-conductor (0.3mm 2 ) chloroprene shielded cable, 7.6 mm diameter by 5 m long, terminated with NDIS connector plug (Shield wire is connected to mainframe.) Safe Overload Rating : 1% Natural Frequency : See table below. Weigt : See table below Connector plug C LU-KE LU-KE LU-0KE LU-0KE LU-1TE LU-2TE LU-5TE LU-10TE LU-TE Rated Capacity ±0N ±1kN ±2kN ±5kN ±10kN ±kn ±kn ±kn ±0kN Natural Frequency 1.54kHz 2.16kHz 3.28kHz 2.66kHz 4.2kHz 4.97kHz 3.5kHz 3.14kHz 2.5kHz A B C φd E φf G H φj (K) SR M5 d=8 M8 d=8 M8 d=12 M8 d=12 M8 d=15 M8 d=15 M8 d=15 in Combination with Special Accessories M8 P=1.25 d=12 M12 P=1.75 d=17 M14 P=2 d=22 M18 P=1.5 d=22 M26 P=2 d=35 M36 P=2 d=45 M P=3 d= Weight * Saddle 2.8kg CA-1B Mount Base CF- 2.8kg 2.8kg 2.8kg 5.0kg 9.5kg 22.0kg CA-1B CF- *not including cable In Comination with Rotating Attachment RJ and Ball Joint TU C 1 E 3 B (approx.) A (approx.) 1Load Cell LU-KE LU-KE LU-0KE LU-0KE LU-1TE LU-2TE LU-5TE LU-10TE LU-TE 2Rotating Attachment 3Ball Joint A B C φd φe F G Static Breaking Load RJ-02 RJ-05 RJ-1 RJ-2 RJ-5 RJ-10 RJ- TU-8 TU-12 TU-14 TU-18 TU-26 TU-36 TU Notes: 1. Rotation attachment RJ is not applicable for compression load measurement. 2. Special accessories for tension loads should be mounted at our factory. 3. Dimensions A and B are approximate, since the ball joint is screw-in type M8 P=1.25 M12 P=1.75 M14 P=2 M18 P=1.5 M26 P=2 M36 P=2 M P=3 1.4kN 2.9kN 5.8kN 14.7kN 29.4kN 58.8kN 136.3kN Physical quantity indication Static measurement Dynamic measurement 2 D 3 LU-E WGA-6B Data Loggers UCAM-B 3-25 Universal Recorders EDX-0A

46 2-53 LUH-F High-Accuracy Tension/Compression Load Cells Nonlinearity : within±0.05%ro 0 N to 0 kn LUH-~0KF Nonlinearity : Within±0.02% RO Hysteresis : Within±0.02% RO Repeatability : 0.02% RO or less Zero Float : 0.02% RO or less (LUH-KF to 0KF) Rated Output : 2 mv/v (00μm/m) ±0.1% Safe Temperature Range : -35 to C Compensated Temperature Range : -10 to C Temperature Effect on Zero Balance : Within±0.0015% RO/ C Temperature Effect on Output : Within±0.001%/ C V AC or DC Excitation Voltage : 1 to 10V AC or DC 3Ω±0.5% 3Ω±0.5% Cable : 6-conductor (0.5 mm 2 ) chloroprene shielded cable, 9.5 mm diameter by 5 m long, with press-fit terminal for 4 mm (Shield wire is not connected to mainframe.) LUH-1~TF Safe Overload Rating : 1% Natural Frequency : See table below. See table below. Others : Drop prevention stopper mountable( ) Critical overload : 0% (LUH- to 0KF) Standard Accessories 4 hexagon socket head setscrews M5 L=10 mm (30 mm with LUH-10TF and TF) 1 hexagon bar (opposite side 25 mm) Ball joint is required for tension load measurement. Remote sensing possible (Refer to page 9-13.) Excellent Zero Float Characteristics (LUH- to 0KF) Tension/Compression Load Cells Remote sensing possible (Refer to page 9-13.) LUH-F series is tension/compression load cells featuring within ±0.05%RO nonlinearity. The hermeticallysealed structure with inert gas filled in ensures stable characteristics. LUH-KF LUH-KF LUH-0KF LUH-0KF LUH-1TF LUH-2TF LUH-5TF LUH-10TF LUH-TF ±0N ±1kN ±2kN ±5kN ±10kN ±kn ±kn ±kn ±0kN Natural Frequency 1.4kHz 2.2kHz 3.1kHz 4.6kHz 4.2kHz 6kHz 5.2kHz 4.5kHz 3.7kHz Weight * 2.1kg 4kg 4kg 9kg 18kg 38kg *not including cable ( )Customers have to prepare anti-dropping stoppers by them self. Bared at the tip Pressure bonded terminal (for remote sensing) ZERO FLOAT Output Rated output Zero float means such a phenomenon that a cycle of continuously applied tension and compression loads causes the zero to float. The value is expressed in percentage of the rated output. It is also called cyclic zero shift. Compression load d a Tension load Rated capacity Note: Arrow direction may be reverse. a Zero Float (%RO) d 2-53

47 4 M8 d=15 (for mounting with anti-dropping stopper) 10 (8) 2 M5 (90 position) 24 SR A A M (N) B 2 M5 (90 position) H K D E G F SR J 2-54 LUH-KF LUH-KF LUH-0KF LUH-0KF A M12 P= M18 P= B B M5 6 drilled d=36 (90 position) B 22 4 M8 d=15 A 98 LUH- to 0KF (89) 44.5 R3/4 H L 2 M5(P) C J 4 Q R3/4 4 M8 T S LUH-1 to TF LUH-1TF LUH-2TF LUH-5TF LUH-10TF LUH-TF A B φc φd φe F G H J K L M (N) (P) Q SR S T U φv M14 P=2 M18 P=1.5 M26 P=2 M36 P=2 M P= drilled d=36 6 drilled d=36 9 drilled d=42 9 drilled d=54 9 drilled d=65 M8 d=10 M8 d=10 M16 d=16 M d=15 M24 d= d=12 d=12 d=15 d=15 d= LUH-KF to 5TF Dimensions in Combination with Mount Base In Combination with Saddle CA and Mount Base CF (LUH- to 0KF) at equal distance 1 Load cell LUH-F 2 Saddle CA-2B 3 Mount base CF- 4 Hexagon socket head bolt 4-M8 L=30 (included in standard accessories of mount base) When using in with special accessories, consult with our sales engineer at equal distance In Combination with Movable Saddle ER and Mount Base CF (LUH-KF to 2TF) Load cell LUH-F 2 Movable saddle ER-2B 3 Mount base CF- (1T, 2T) 4 Hexagon socket head bolt 4-M8 L=30 (included in standard accessories of mount base) Note: Special accessories for tension load measurement should be assembled at our factory. 4 M8 at equal distance 4 13 at equal distance 1Load Cell LUH-KF LUH-KF LUH-0KF LUH-0KF 2 Ball Joint TU-12 In Combination with Ball Joint TU E F C D A B C D E F M12 P= TU M18 P= B(approx) A(approx) Static Breaking Load 1.4kN 2.9kN 5.8kN 14.7kN From the viewpoint of guaranteed accuracy, hook and shackle cannot be combined. Physical quantity indication Static measurement Dynamic measurement LUH-F WGA-6B Data Loggers UCAM-B 3-25 Strain Amplifiers DPM-900 Series 3-5 Memory Recorder/Analyzers EDX-3000A

48 2-55 LUK-A Tension/Compression Load Cells Thin 5 kn to 2 MN LUK-A-5 to KN Nonlinearity : Within±0.1% RO (LUK-A-5KN to 0KN) Within±0.2% RO (LUK-A-0KN to 2MN) Hysteresis : Within±0.1% RO (LUK-A-5KN to 0KN) Within±0.2% RO (LUK-A-0KN to 2MN) Repeatability : 0.05% RO or less (LUK-A-5KN to 0KN) 0.1% RO or less (LUK-A-0KN to 2MN) Rated Output : ±2.4mV/V (±μm/m) ±0.1% (±2.4mV/V (±00μm/m) ±10% with 5KN to KN) Safe Temperature Range : -35 to C Compensated Temperature Range : -10 to C Temperature Effect on Zero Balance : Within±0.005% RO/ C Temperature Effect on Output : Within±0.005%/ C 15V AC or DC Excitation Voltage : 1 to 10V AC or DC 3Ω±1% 3Ω±1% Cable : 4-conductor (0.3mm 2 ) chloroprene shielded cable, 7.6 mm diameter by 5 m long, terminated with connector plug (Shield wire is not connected to mainframe.) LUK-A- to 0KN Safe Overload Rating : 1% Natural Frequency : See table below. See table below (not including cable) Safe Lateral Force Component : See table below. Safe Moment : See table below. TEDS-installed versions can be manufactured. Inquiries are welcome. Connector plug Compact,Light Weight, Tension/ Compression Load Cells The thin structure is suitable for installation where the height is limited. The service life can be extended by using with one-half the rated capacity if repetitive loads are applied continuously. Installation Example When used for tension, special accessories such as ball-joint and rotating attachment. Screw Shaft Load Cell Piston Smoothing hole To Ensure Safe Usage Be sure to prevent the shaft from turning when using for hanging load measurement. Link 2-55

49 2-56 G H H A B C C B E 21 D R1/2 G D A B H H C C B E 25 R1/2 8 F (J) LUK-A-5 to KN 8 F J LUK-A- to 0KN A B C G D H H C B R1/2 E F J LUK-A-1 to 2MN LUK-A-5KN LUK-A-10KN LUK-A-KN LUK-A-KN LUK-A-KN LUK-A-0KN LUK-A-0KN LUK-A-1MN LUK-A-2MN Rated Capacity ±5kN ±10kN ±kn ±kn ±kn ±0kN ±0kN ±1MN ±2MN Natural Frequency 7.4kHz 10.8kHz 8.5kHz 11kHz 9kHz 7.5kHz 5.2kHz 5kHz 3.9kHz Safe Moment 15N m 30N m N m 1N m 0N m 1kN m 2.5kN m 5kN m 10kN m Safe Lateral Force Component 2N 0N 1kN 2.5kN 5kN 10kN 25kN kn kn φa φb φc D φe φf G H (J) M12 P=1.75 M18 P=1.5 M24 P=1.5 M36 P=2 M P=2 M76 P=3 M P=3 M1 P= Weight 900g 2kg 4kg 7kg 18kg kg 90kg 245kg Physical quantity indication Static measurement Dynamic measurement LUK-A WGA-6B Data Loggers UCAM-B 3-25 Strain Amplifiers DPM-900 Series 3-5 Memory Recorder/Analyzers EDX-3000A

50 2-57 LU-A Straight Beam System to 0 N Small-Capacity Tension/Compression Load Cells TEDS-installed versions can be manufactured. Inquiries are welcome. Nonlinearity : Within±0.3% RO Hysteresis : Within±0.2% RO Repeatability : 0.2% RO or less Rated Output : 1.5 mv/v (3000μm/m) ±0.5% Safe Temperature Range : - to 75 C Compensated Temperature Range : -10 to 65 C Temperature Effect on Zero Balance : Within±0.01% RO/ C Temperature Effect on Output : Within±0.01%/ C 15V AC or DC Excitation Voltage : 1 to 10V AC or DC 3Ω±0.5% 3Ω±0.5% Cable : 4-conductor (0.3mm 2 ) chloroprene shielded cable, 7.6 mm diameter by 5 m long, with connector plug (Shield wire is connected to mainframe.) Small capacity, High sensitivity Tension/Compression Load Cells Safe Overload Rating : 1% Natural Frequency : See table below. Approx. 2.3 kg A straight beam is used for the strain column to enable highly accurate measurement of small loads. LU-5KA LU-10KA LU-KA ±N ±N ±0N Natural Frequency 0Hz 330Hz 0Hz in Combination with Mount Base In Combination with Mount Base CF- SR11 90 M d=15 2 M3 L=5 setscrew LU-A Hexagon socket head bolt 4 M6 L= M d= M6 d=7 Mount basecf at equal distance 106 Connector plug 122 Hexagon socket head bolts for connection between load cell and mount base are standard accessories to mount base. Physical quantity indication Static measurement 2-57 LU-A WGA-6B WGI-0A Sensor Interfaces PCD-430A 3-51

51 LVS-A/LTS-A Ultra Small-Capacity Load Cells Compact & Lightweight mn to N 2-58 LVS-A LTS-A TEDS-installed versions can be manufactured. Inquiries are welcome. These Load Cells are Designed to Accurately Measure Small Loads Ranging from mn to N Compact and lightweight High accuracy Easy to handle These load cells are designed to accurately measure small loads ranging from mn to N. Easy to install and handle, the LVS-A series measures loads in vertical direction to the mounted surface and the LTS-A series, in horizontal direction. 2 M2 R5 R1.5 Sensitivity (Base) (Base) M2 nut M2 0.4 R5 R1.5 Sensitivity 55 35(Base) (Base) Nonlinearity : Within±0.5% RO Hysteresis : Within±0.5% RO Repeatability : 0.5% RO or less Rated Output : 1.2 mv/v (μm/m) or more (LVS-5GA & 10GA) 1.5 mv/v (3000μm/m) or more (LVS/LTS-GA to 2KA) Safe Temperature Range : -10 to C Compensated Temperature Range : 0 to C Temperature Effect on Zero Balance : Within±0.05% RO/ C Temperature Effect on Output : Within±0.1%/ C 6V AC or DC Excitation Voltage : 1 to 2V AC or DC 1Ω±10% 1Ω±10% Cable : 4-conductor (0.05 mm 2 ) chloroprene shielded cable, 3 mm diameter by 1 m long, terminated with connector plug (Shield wire is not connected to mainframe.) Safe Overload Rating : 1% Critical Overload : See table above. Approx. g (not including cable) LVS-5GA LVS-10GA LVS-GA LVS-GA LVS-GA LVS-0GA LVS-0GA LVS-1KA LVS-2KA LTS-GA LTS-GA LTS-0GA LTS-0GA LTS-1KA LTS-2KA Natural Frequency Hz 111Hz 147Hz 294Hz 455Hz 667Hz 12Hz 10Hz Hz 256Hz 385Hz 625Hz 0Hz 16Hz 10Hz Rated Capacity mn mn 0mN 0mN 1N 2N 5N 10N N 0mN 1N 2N 5N 10N N To Ensure Safe Usage Critical Overload 0% 0% 2% 0% (10) % The load cell should be carefully installed. Especially, never apply any impact (force) in sensitivity direction. When mounting the rod to the measuring object, do not apply any bending or twisting force. (10) Connector plug LVS-A LTS-A Physical quantity indication Static measurement Dynamic measurement LVS-A/LTS-A WGI-0A Data Loggers UCAM-B 3-25 Strain Amplifiers DPM-900 Series 3-5 Sensor Interfaces PCD-430A

52 2-59 LUB-B Beam-Type Load Cells Nonlinearity : within±0.05%ro( to 0 N) N to kn TEDS-installed versions can be manufactured. Inquiries are welcome. Compact and Lightweight, Metal Bellows Nonlinearity : within±0.05%ro 1 Special steel body 1 Corrosion-resistant 2 1:5 to KB 2:KB to 2TB LUB-5KB to KB feature an nonlinearity of within ±0.05%RO and LUB-KB to 2TB feature corrosionresistant stainless steel body and bellows. As load detectors, they enable configuration of accurate and stable weighing systems for conveyors and tanks. 51 LUB-5 to KB LUB-KB to 2TB (Mounting hole) 8.1 (Load point) M8 d=8 42 LUB-5 to KB Load direction 51 B 2 G D E K A J F H (Load point) C B LUB-KB to 2TB Bared at the tip Load direction Nonlinearity : Within±0.03% RO (LUB-B-5KB to KB) Within±0.05% RO (LUB-B-KB to 2TB) Hysteresis : Within±0.03% RO (LUB-B-5KB to KB) Within±0.05% RO (LUB-B-KB to 2TB) Repeatability : 0.03% RO or less Rated Output : 2 mv/v (00μm/m)±0.3% Safe Temperature Range : - to C Compensated Temperature Range : -10 to C Temperature Effect on Zero Balance : Within±0.003% RO/ C Temperature Effect on Output : Within±0.003%/ C V AC or DC Excitation Voltage : 1 to 12V AC or DC 435Ω±Ω(LUB-B-5KB to KB) 0Ω±Ω(LUB-B-KB to 2TB) 3Ω±2 Ω Cable : 4-conductor (0.3 mm 2 ) chloroprene shielded cable, 7.6 mm diameter by 3 m long (5 m long with LUB-B-KB to 2TB), bared at the tip (Shield wire is not connected to mainframe.) Safe Overload Rating : 1% Natural Frequency : See table below. See table below (not including cable) Protection Rating : IP67 (Watertight type conforming to JIS C 09) In Combination with Special Accessories LUB-B in with mount base with stopper LUB-B/C in with spacer LUB-B/C in with hanger LUB-B LUB-B,C LUB-B,C Load Load Spacer LE Patch CW O-ring Mount base with stopper LD-005 Patch CW O-ring Hanger TW Load LUB-5KB LUB-10KB LUB-KB LUB-30KB LUB-KB LUB-KB LUB-0KB LUB-0KB LUB-1TB LUB-2TB Rated Capacity N N 0N 300N 0N 1kN 2kN 5kN 10kN kn Natural Frequency 2Hz 3Hz 0Hz 6Hz 0Hz 1.8kHz 1.9kHz 1.1kHz 1.2kHz 1.1kHz A B φc D E F φg φh J K See dimensional drawing above Weight 3g 3g 1.5kg 2.8kg Patch CW-005 CW-02 CW-1 CW-2 Mount Base w/ Stopper LD-005 Spacer LE-005 LE-02 LE-1 LE-2 Hanger TW-002 (for 5 to KB) TW-005 (for 5 to KB) TW-02 TW-1 TW-2 Physical quantity indication Static measurement Dynamic measurement 2-59 LUB-B WGA-6B Data Loggers UCAM-B 3-25 Strain Amplifiers DPM-900 Series 3-5 Sensor Interfaces PCD-430A 3-51

53 LUB-C Beam-Type Load Cells Nonlinearity : within±0.05%ro 5 to kn 2- LUB-0KC to 2TC TEDS-installed versions can be manufactured. Inquiries are welcome. Nonlinearity : Within ±0.05% RO Hysteresis : Within ±0.05% RO Repeatability : 0.03% RO or less Rated Output : 2 mv/v (00 μm/m) ±0.5% Safe Temperature Range : - to C Compensated Temperature Range : -10 to C Temperature Effect on Zero Balance : Within ±0.003% RO/ C Temperature Effect on Output : Within ±0.003%/ C V AC or DC Excitation Voltage : 1 to 12V AC or DC 3Ω±8% 3Ω±1% Cable : 4-conductor (0.14mm 2 ) chloroprene shielded cable 6mm diameter by 2m long bared at the tip (Shield wire is not connected to mainframe.) Developed as OEM-Oriented Industrial Beam-Type Load Cells Low price Compact and lightweight Nonlinearity : within±0.05%ro Developed as OEM-oriented industrial beam-type load cells with nonlinearity of within ±0.05%RO. As load detectors, LUB-C series enables configuration of accurate and stable weighing systems for conveyors and tanks. Safe Overload Rating : 1% Natural Frequency : See table below. See table below (not including cable) G F E J (Load point) H L 2 K Load direction C D B A Bared at the tip LUB-0KC LUB-2TC Rated Capacity 5kN kn Natural Frequency 1.3kHz 1.3kHz A B C D E F G H φj φk L Weight (App.) including cable 1.3kg 2.7kg Patch Spacer Hanger LE-1 LE-2 Physical quantity indication Static measurement Dynamic measurement LUB-C WGA-6B Data Loggers UCAM-B 3-25 Strain Amplifiers DPM-900 Series 3-5 Sensor Interfaces PCD-430A

54 2-61 LFM-A Compact & Lightweight Compact 6-Component Force Transducers 1 kn & 3 kn Compact,High Sensitivity Center Hole Type of 6-Component Force Transducers Enables simultaneous measurement of 3 forces (Fx, Fy, Fz) in 3 axial directions orthogonal to the transducer and 3 moments (Mx, My, Mz) around the axes. An 8-channel measuring instrument amplifies the transducer's 8 output components in strain quantity and calculates 6-component force. The equation is described in the LFM-A manual. Nonlinearity : Within ±0.5% RO Hysteresis : Within ±0.5% RO Interference : ±1.5% RO (after correction by interference correction coefficient stated in Calibration Sheet) Rated Output : See table below. Safe Temperature Range : -10 to C (noncondensing) Compensated Temperature Range : 0 to C(noncondensing) Temperature Effect on Zero Balance : Within ±0.05% RO/ C or less Temperature Effect on Output : Within ±0.05%/ C or less 12V AC or DC Excitation Voltage : 1 to 5V AC or DC Input/ 3Ω±3% Cable : 16-conductor (0.11 mm 2 ) twisted pair vinyl shielded cable, 6.6 mm diameter by 55 cm long, bared at the tip (Shield wire is not connected to mainframe) Safe Overload Rating : 1% Material : Main unit LFM-A-1KN: Aluminum (metallic finish) Main unit LFM-A-3KN: SUS (metallic finish) Cover: Black anodic oxide coating aluminum Cable holder: Anodic oxide coating aluminum See table (not including cable) Protection Rating : IP LFM-A-1KN LFM-A-3KN FX :±0N FY :±0N FZ :±0N MX :±N m MY :±N m MZ :±25N m FX :±3000N FY :±3000N FZ :±3000N MX :±N m MY :±N m MZ :±N m Rated Output Natural Frequency 5kHz 5kHz The Rated Output is an Interference Correction Further Output. Weight (applied to pin hole) z Y H7 d= M4 d=5 Note: conductor (0.11 mm 2 ) twisted pair vinyl shielded cable, 6.6 mm diameter by 55 cm long, bared at the tip To Ensure Safe Usage Prepare a plate shaped member for installing the LFM-A with sufficient strength. It is recommendable that LFM- A-3KN should be applied on the steelplate whose thickness is more than 10mm. With same reason,we recommend as follows. LFM-1KN should be applied on an aluminum alloy board which is not less than 15mm thick. If the LFM-A is installed on a low rigid mounting plate, interference may be increased. X Dynamic measurement 2-61 Original point and moment center of x-, y- and z-axes coincide with transducer height and circumferential center. LFM-A Sensor Interfaces PCD-0A 3-51 Universal Recorders EDX-0A 3-69 Compact Recording System EDX-10A 3-61

55 LFX-A With Built-in Amplifier Compact 6-Component Force Transducers with Built-in Amplifier 2-62 Compact, Amplifier Built in Wiring Hole, 4 mm Diameter, Provided at the Center Enables simultaneous measurement of 3 forces (Fx, Fy, Fz) in 3 axial directions orthogonal to the transducer and 3 moments (Mx, My, Mz) around the axes. It outputs 6 voltage signals proportionated to 6 detected components. 16-conductor (0.11 mm2) twisted pair vinyl shielded cable, 6.6 mm diameter by 55 cm long, bared at the tip (9 conductors) (applied to pin hole) (4) 45 (73) 4 3 H7 d= M4 d=5 z 0.2 Original point and moment center of x-, y- and z-axes coincide with transducer height and circumferential center. Y X Nonlinearity : Within±0.5% RO Hysteresis : Within±0.5% RO Interference : ±1.5% RO (after correction by interference correction coefficient stated in Calibration Sheet) Note : Output voltage signals of 6-component force should be corrected by interference correction coefficient. Output of each component concerns output of other components. Rated Output : Approx. ±10 mv (from mv output with no load at the center) Safe Temperature Range : -10 to C (noncondensing) Compensated Temperature Range : 0 to C (noncondensing) Temperature Effect on Zero Balance : Within±0.05% RO/ C Temperature Effect on Output : Within±0.05%/ C No-Load Output: mv at the center (See figure below.) High limit of output () Output voltage (mv) 00 0 () Low limit 1 of output 0 1 Load(%) Frequency Response : DC to 0 Hz (+1 db to -3dB) Power Supply : 5V DC±10%, 1 ma or less Cable : 16-conductor (0.11mm 2 ) twisted pair vinyl shielded cable, 6.6 mm diameter by 55 cm long, bared at the tip (9 conductors) (Shield wire is not connected to mainframe) Safe Overload Rating : 1% Material : Main unit LFX-A-1KN: Aluminum (metallic finish) Main unit LFX-A-3KN: SUS (metallic finish) Cover : Black anodic oxide coating aluminum Cable holder : Anodic oxide coating aluminum See table (not including cable) Protection Rating : IP To obtain the rated output of ±10 mv for each of 6-component force, zero drift due to installation conditions including tightening and loading should be made within ±0 mv. LFX-A-1KN LFX-A-3KN FX : ±0N FY : ±0N FZ : ±0N MX : ±N m MY : ±N m MZ : ±25N m FX : ±3000N FY : ±3000N FZ : ±3000N MX : ±N m MY : ±N m MZ : ±N m Weight 210g 4g To Ensure Safe Usage Prepare a plate shaped member for installing the LFX-A with sufficient strength. It is recommendable that LFX-A-3KN should be applied on the steelplate whose thickness is more than 10mm. With same reason,we recommend as follows. LFX-1KN should be applied on an aluminum alloy board which is not less than 15mm thick. If the LFX-A is installed on a low rigid mounting plate, interference may be increased. Dynamic measurement LFX-A Sensor Interfaces PCD-430A 3-51 Compact Recording System EDX-10A 3-61 Universal Recorders EDX-A 3-65 Universal Recorders EDX-0A 3-69 Memory Recorder/Analyzers EDX-3000A

56 2-63 LAT-0A Series 6-Component Force Measuring Systems 300N Configuration 6-component force transducer LAT-A Signal processor FDP-106A PC (not included) LAT-A General : See table below Safe Overload Rating : 1% Nonlinearity : Within±0.5% RO Hysteresis : Within±0.5% RO Interference : ±0.8% RO Maximum Error : ±1.5% RO (±3% RO with LAT-KA-2) Resolution : 0.05% FS Temperature Effect on Zero Balance : Within ±0.25% RO/ C Temperature Effect on Output : Within ±0.05%/ C Compensated Temperature Range : 0 to C FDP-106A stated above are values measured with our calibrators under incompany standard conditions. Enables Highly Accurate Measurement Possible to Inference Correction by Arithmetic Processing. LAT-1030KA-1 LAT-1030KA-2 Fx N Fy N Fz N Mx N m 10 My N m 10 Mz N m 10 Each system in the LAT-0A series consists of the LAT-A 6-component force transducer and the FDP-106A signal processor. The LAT-A simultaneously detects 3 forces in 3 axial directions orthogonal to the transducer and 3 moments around the 3 axes. The FDP-106A automatically eliminates interference components contained in transducer output through calculation. By minimizing errors due to interference, the system enables highly accurate measurement of both single and multiple component force loads. (Patented) 5-V output available with the rated load To guarantee measurement accuracy, performance with multiple component force loaded is indicated with a maximum error (see note in the next page). Highly accurate measurement possible even with multiple component force loaded Simultaneous sampling of 6-component force and processing signals up to approximately 300 Hz possible The compact, lightweight transducer is strain gage based and is cased with a highly rigid special aluminum alloy. Calibration coefficient is preset in the signal processor, enabling immediate measurement by connecting a monitor indicator. Force and moment can be read directly on a PC if connected. Direct reading mode is provided to read force and moment at the load point. High/low limit and hysteresis width of the high/ low limit are set to alarm output. Fz 6-Component Force Transducer LAT-A : Fx, Fy, Fz=300N Mx, My, Mz=10, N m See table in the previous page for s. Safe Overload Rating : 1% Natural Frequency (with all models) : Fx, Fy : Approx. 2.3 khz, Fz: Approx. 5.5 khz Mx, My : Approx. 8 khz, Mz: Approx. 4 khz Excitation Voltage : 2.5V DC 5V DC 58.3Ω ±10% 3Ω ±2% Compensated Temperature Range : 0~ C Safe Temperature Range : 0~ C Temperature Effect on Zero Balance : Within 0.05% RO/ C Temperature Effect on Output : Within 0.05%/ C Each model approx. 2g (not including cable) Protection Rating : IP30(JIS C 09) Cable : 14-conductor (0.3 mm 2 ) PVC shielded cable, 9 mm diameter, with connector plug at both ends. N-78 for connection to FDP-106A (Shield wire is not connected to mainframe) For measurement of displacement and inclinaton angle, contact us. Standard Accessories Communications program (Windows version), torque wrench, hexagon socket wrench, parallel pins φ4 and φ8, connection cable N-78 Mz c a e Mx d b Fx 2-63 My Fy

57 2-64 Signal Processor FDP-106A Input : Number of channels: Max. 6 (6-component force) Zero balance adjustment : Automatic (true electron method) Bridge excitation voltage : 2.5V DC Analog Output : Number of channels: 6 Output: ±5 V (1% the rated output of 6-component force transducer may be made ±5 V) Resolution: 0.05% FS Frequency response range: DC to approx. 300 Hz Initial setting: ±5V analog output for the rated capacity of 6-component force transducer, 0 mm for coordinates X, Y and Z at the load point Serial Interface : RS-232C Transmission mode: Start-stop synchronized mode Transmission rate: 90 bps fixed Data: 8 bits, Parity: None, Stop bit: 1 Transmission contents: Data, setting conditions Data format: Binary or ASCII Connector: D-Sub 25 pin, female PC connection: Optional interface cable for RS-232C Sampling Frequency : When not using digital output 0.72 ms/6 channels (cutoff frequency 366 Hz) When using digital output 22.9 ms/6 channels in binary format (cutoff frequency 11 Hz) 45.7 ms/6 channels in ASCII format (cutoff frequency 6 Hz) Nonlinearity : Within ±0.05% FS Calculation Error : in Interference : Compensation : Within ±0.1% FS Stability : Zero ±0.25μV/V/ C, Sensitivity ±0.01%/ C Functions : Overinput checking, automatic zero balance, load point correction, alarm Monitor Indicator : LED Alarm Output : Open collector Operating Temperature/Humidity Range : 0 to C, 95% RH or less (noncondensing) Power Supply : AC V±10% Dimensions : 255 (W) x 1 (D) x 88 (H) mm (excluding protrusions) Approx. 2.5 kg Standard Accessories Options Output cable U-58 (6 pcs.) AC power cable P-18 with conversion adapter CM-33 RS cross cable N-23, Mounting fixture FL-1A Communication Program(Attached to LAT-A) (Windows Version) Operating Environment OS : Windows XP/7 Memory : 64M or more Display : 0 0 dots or more 4 M5 d=7 10 Load reference point M5 d=7 Note on Maximum Error Mx Fx Fz Mz (62.5) Definition A maximum error denotes a maximum deviation in plus and minus directions from the characteristic curve observed when testing devices or equipment according to stipulated procedures under standard operating conditions. Description specifications of a load cell include non-linearity, hysteresis and repeatability. In the case of a 6-component force transducer, interference is added to these performance specifications. All these specifications apply to a single component force, that is, force or moment in a single direction. However, the 6-component force transducer rarely receives a single component force and detects 2 or more component force. Accordingly, characteristic values for multiple component force should be considered. To solve the problem, a maximum error is newly included in performance specifications of the LAT-A series. The maximum error is obtained as follows: Apply an external force FM of known value to the 6-component force transducer and read resultant output values of Fx, Fy, Fz, Mx, My and Mz. Referring to the magnitude and direction of the external force FM, calculate 6-component force FxM, FyM, FzM, MxM, MyM and MzM. A maximum error of Fx is calculated using the following equation: Maximum error of Fx = (Fx - FxM)/FxO x (% RO) *Indentation is not aligned. where, FxO is the rated capacity for the force in X direction. Maximum errors of other components are calculated in the same manner. Practically, we tested through simultaneous application of 3-component force in 3 directions and 6-component force/moment in 3 directions and confirmed that the calculated maximum errors satisfy the stated specification. Thus, the LAT-A series 6-component force transducers are assured of the accuracy in measurement of multiple component force loads, enabling safe operation under any loading conditions d= H7 d=6 (2) 2 4 d=6 8 H7 d=6 45 Approx. 145 with cable connected My Fy Static measurement LAT-0A Signal processor FDP-106A

58 2-65 LSM-B-SA1 3-Component Force Transducers 10 to 0N Enables Force Measurement in X, Y and Z Directions. The Compact, Lightweight Strain Gage Based Design is Suitable for Experiments. (Patented) Nonlinearity : Within±0.5% RO Hysteresis : Within±0.5% RO Rated Output : Approx. 0.5 mv/v (0μm/m) Interference : Within ±3%RO Safe Temperature Range : 0 to C Compensated Temperature Range : 0 to C Temperature Effect on Zero Balance : Within±0.05% RO/ C Temperature Effect on Output : Within±0.05%/ C 10V AC or DC Excitation Voltage : 1 to 5V AC or DC 2Ω±5% 2Ω±5% Cable : 4-conductor (0.08 mm 2 ) chloroprene shielded cable, 4 mm diameter by 5 m long, with connector plug to the transducer side and bared to the amplifier side (Shield wire is not connected to mainframe.) Safe Overload Rating : 1% Natural Frequency : See table below. See table (not including cable) Safe Moment : See table below. For the cable terminated with NDIS connector, suffix "-P" to the model number. Fx (Mx) 4 M5 d=10 Fy (My) (.5) 8 d=2 To Ensure Safe Usage LSM-B-SA1 series does not feature waterproof structure. Notes : 1. Mx, My and Mz cannot be measured. 2. Arrows indicate directions of component force in plus polarity acting to the B plane with the A plane fixed. (15) (25) (Mz) Fz A B (2) (2) 37 LSM-B-10NSA1 LSM-B-NSA1 LSM-B-NSA1 LSM-B-NSA1 LSM-B-0NSA1 LSM-B-0NSA1 Fx, Fy, Fz 10N N N N 0N 0N NaturalFrequency X Y Z 0.3kHz 0.4kHz 0.8kHz 1.3kHz 2.5kHz 2.2kHz 0.2kHz 0.3kHz 0.6kHz 0.9kHz 2.0kHz 1.8kHz Safe moment is stated for reference to strength. Safe Moment Mx, My, Mz 1.2N m 2.4N m 5.9N m 9.8N m 24N m 59N m Weight 0g 1.6kg d= Flat-to-flat, 4 flats at equal distance at 90 6 M5 d=8 Bared at the tip Static measurement 2-65 LSM-B-SA1 Strain Amplifiers DPM-900 Series 3-5 Sensor Interfaces PCD-430A 3-51 Universal Recorders EDX-A 3-65 Memory Recorder/Analyzers EDX-3000A 3-79

59 LUR-B-SA1 Jack Load Cells 10kN to 2MN 2-66 Nonlinearity : Within±0.2% RO (LUR-B-10 to 0KNSA1 ) Within±0.5% RO (LUR-B-300KNSA1 to 5MNSA1) Hysteresis : Within±0.1% RO (LUR-B-10 to 0KNSA1 ) Within±0.5% RO (LUR-B-300KNSA1 to 5MNSA1) Rated Output : ±1 mv/v (00μm/m)±1% Safe Temperature Range : -10 to C Compensated Temperature Range : 0 to C Temperature Effect on Zero Balance : Within±0.01% RO/ C Temperature Effect on Output : Within±0.01%/ C 15V AC or DC Excitation Voltage : 1 to 12V AC or DC 3Ω±2% 3Ω±2% Cable : 4-conductor (0.3 mm 2 ) chloroprene shielded cable, 7.6 mm diameter by 10 m long, terminated with connector plug Special Design for Jacks, Low Price Various Capacity Ranges LUR-B-SA1 series load cells are designed to measure loads applied to jacks when lifting up or moving a large machinery or structure in civil engineering and construction fields. These load cells enable the operators to prevent overloads, unbalanced loads, or movement of the center of gravity. Safe Overload Rating : 0% See table (not including cable) With the capacity of 0 kn or more, calibration is performed for compression load only. F H H F D E E (C) B A (C) G Connector plug LUR-B-10KNSA1 LUR-B-KNSA1 LUR-B-30KNSA1 LUR-B-KNSA1 LUR-B-KNSA1 LUR-B-0KNSA1 LUR-B-300KNSA1 LUR-B-0KNSA1 LUR-B-1MNSA1 LUR-B-1.5MNSA1 LUR-B-2MNSA1 A B (C) φd φe F G H ±10kN ±kn ±30kN ±kn ±kn ±0kN ±300kN ±0kN ±1MN ±1.5MN ±2MN M12 P=1.75 d=15 M18 P=1.5 d= M24 P=2 d=30 M39 P=2 d=45 M P=2 d=65 M65 P=3 d=65 M85 P=3 d=85 M110 P=3 d=118 M1 P=4 d=1 M1 P=4 d= Weight 1.4kg 2.1kg 2.2kg 2.5kg 5.2kg 8kg 15kg 55kg 85kg kg Physical quantity indication LUR-B-SA WGA-6B

60 2-67 LTA-C-S Crane Load Cells For Cranes to 0 kn Nonlinearity : Within±1% RO Hysteresis : Within±1% RO Rated Output : Approx. 0.6 to 0.7 mv/v (10 to 10μm/m) Safe Temperature Range : - to C Compensated Temperature Range : -10 to C Temperature Effect on Zero Balance : Within±0.05% RO/ C Temperature Effect on Output : Within±0.05%/ C 12V AC or DC Excitation Voltage : 1 to 10V AC or DC 3Ω±5% 3Ω±5% Cable : 4-conductor (0.75 mm 2 ) chloroprene shielded cable, 10 mm diameter by 10 m long, with press-fit terminal (Shield wire is not connected to mainframe.) Breaking Overload Rating : Approx. 0% Safe Overload Rating : 1% See table (not including cable) B A High Strength,Easy to Handle High Reliability,High Stability These series of tension load cells can be used as detectors for jib crane weighing systems and for general tension measurement. T C 2 D (31) (17) KNS(only) Press-fit terminal To Ensure Safe Usage Install the load cell carefully to avoid applying tensile and impact force to the cable and prevent the load cell from receiving bending or twisting force. Prepare a safety device such as a link against accidental hazards so that it supports loads in place of a broken load cell. LTA-C-KNS LTA-C-KNS LTA-C-KNS LTA-C-0KNS LTA-C-300KNS LTA-C-0KNS Rated Capacity kn kn kn 0kN 300kN 0kN A B C D T φ45 φ45 φ φ65 φ75 φ Weight 5kg 5.5kg 11kg 21kg 35kg kg Physical quantity indication 2-67 LTA-C-S WGA-6B WGI-0A 2-167

61 LTR-S-SA1 One-End Revolving Tension Load Cells to kn 2-68 Nonlinearity : Within±0.5% RO Hysteresis : Within±0.5% RO Rated Output : Approx. 1mV/V (00μm/m) Safe Temperature Range : - to C Compensated Temperature Range : -10 to C Temperature Effect on Zero Balance : Within±0.05% RO/ C Temperature Effect on Output : Within±0.05%/ C 12V AC or DC Excitation Voltage : 1 to 5V AC or DC 3Ω±2% 3Ω±2% Cable : 4-conductor (0.3mm 2 ) chloroprene shielded cable, 7.6 mm diameter by 5 m long, terminated with connector plug (Shield wire is not connected to mainframe.) Compact, Lightweight, Low price For Measurement of Traction and Tensile Force of Rope LTR-S-SA1 series load cells are suitable for measurement of tensile force of rope. Since the hook at one end revolves together with the rope which may revolve due to twisting, easy installation and handling are ensured. Safe Overload Rating : 1% Static Breaking Overload Rating : 0% (1% with KNSA1) Approx. 3.6kg (not including cable) LTR-S-KNSA1 LTR-S-30KNSA1 LTR-S-KNSA1 φa φb kn 30kN kn To Ensure Safe Usage When loaded, sliding friction prevents the revolving part from revolving. Do not use for measurement of hanging load. Revolving Side Fixed Side Not prescribed B 30 A Connector plug 2 Physical quantity indication Dynamic measurement LTR-S-SA WGA-6B Strain Amplifiers DPM-900 Series

62 2-69 LTP-S-S Pin-Type Load Cells 10 to 0kN Nonlinearity : Within±1 to 2% RO (depends on user's spec.) Hysteresis : Within±1 to 2% RO (depends on user's spec.) Rated Output : Approx. 0.5 to 1 mv/v (0 to 00μm/m) Safe Temperature Range : - to C Compensated Temperature Range : -10 to C Temperature Effect on Zero Balance : Within±0.05% RO/ C Temperature Effect on Output : Within±0.05%/ C 15V AC or DC Excitation Voltage : 1 to 10V AC or DC 0Ω±3% 0Ω±3% Cable : 4-conductor chloroprene shielded cable (length is as required) Safe Overload Rating : 1% Compact, Space-Saving Design For Mounted in the Place of the Axis of Crane's Pulley Specially designed for installation to pin connection Mounted in place of the axis of crane's pulley, LTP- S-S series pin-type load cells enable measurement of hanging loads. Such the feature ensures easy installation and handling. Since strain gages are used as the load detector, each load cell in this series is compact, lightweight and economically priced. Installaton Example Pin-type load cell B C D H E H B C D C E A F A F G G G R1/2 R1/2 LTP-S-10 to KNS LTP-S- to 0KNS LTP-S-10KNS LTP-S-KNS LTP-S-KNS LTP-S-KNS LTP-S-0KNS LTP-S-0KNS φa B C D (E) φf G H 10kN kn kn kn 0kN 0kN Physical quantity indication 2-69 LTP-S-S WGI-0A 2-167

63 LCD-A-S1 to S9 Rectangular Load Cells 30 to kn 2- Nonlinearity : Within±1% RO Hysteresis : Within±1% RO Rated Output : Approx. 1 mv/v (00μm/m) or more Safe Temperature Range : - to C Compensated Temperature Range : -10 to C Temperature Effect on Zero Balance : Within±0.01% RO/ C Temperature Effect on Output : Within±0.01%/ C 15V AC or DC Excitation Voltage : 1 to 10V AC or DC 3Ω±5% 3Ω±5% Cable : 4-conductor (0.75 mm 2 ) fluonlex shielded cable, approx. 8 mm diameter by 10 m long, bared at the tip (Shield wire is not connected to mainframe.) For Measurement of Loads to Pillow Block Hermetically-sealed structure Having a flat top and bottom, LCD-A-S series rectangular compression load cells enable stable installation of a flat board. Can be used for weighing systems of waste and ash cranes or for measurement of compression loads of pillow blocks placed on them. Safe Overload Rating : 1% See table (not including cable) Protection Rating : IP64 (Splashproof type conforming to JIS C 09) To Ensure Safe Usage Take care that there is no foreign matter on the top and bottom of the load cell and the surface of mounting board. 4 H E 2 F D J G R1/2 A (5) B 35 Bared at the tip C LCD-A-30KNS1 LCD-A-30KNS2 LCD-A-30KNS3 LCD-A-KNS4 LCD-A-KNS5 LCD-A-KNS6 LCD-A-KNS7 LCD-A-KNS8 LCD-A-KNS9 A B C D E F G H J 30kN kn kn M22 d=30 M22 d=30 M27 d=35 M22 d=30 M27 d=35 M27 d=35 M30 d=35 M30 d=35 M30 d= Weight 22kg 28kg 28kg 35kg 33kg 35kg kg kg kg Physical quantity indication LCD-A-S1 to S WGA-6B

64 2-71 LCR-B-S7 Tension Meter Load Cells 5 to kn Nonlinearity : Within±0.1% RO (LCR-B-5 to KNS7), Within±0.2% RO (LCR-B-KNS7) Hysteresis : Within±0.1% RO (LCR-B-5 to KNS7), Within±0.2% RO (LCR-B-KNS7) Repeatability : 0.1% RO or less Rated Output : 1 mv/v (00μm/m) ±1% Safe Temperature Range : - to 1 C Compensated Temperature Range : -10 to C Temperature Effect on Zero Balance : Within ±0.005% RO/ C Temperature Effect on Output : Within ±0.005%/ C 15V AC or DC Excitation Voltage : 1 to 10V AC or DC 3Ω±1% 3Ω±1% Cable : 4-conductor (0.75 mm 2 ) fluonlex shielded cable, 8 mm diameter by 10 m long, bared at the tip (Shield wire is not connected to mainframe.) Excellent Environmental Resistance Tension Meter Load Cells High safe overload rating of 300% max. Mechanical stopper activating against overloads of 1 to 0% HermeticalIy-sealed structure with inert gas filled in Highly reliable structure (IP64) Corrosion resistant Cable direction selectable from either left or right Designed for tension meters, LCR-B-S7 series load cells are suitable for load measurement under environments where heat resistance, oil resistance, corrosion resistance and high overload rating are required. Critical Overload Rating : 0% (0% with KNS7) Safe Overload Rating : 300% (0% with KNS7) Material : Stainless steel (excluding the mount base of & KNS7) Protection Rating : IP64 (Splashproof type conforming to JIS C 09) See table (not including cable) To Ensure Safe Usage Never disassemble the mount base, which has the stopper mechanism activating against overloads of 1 to 0%. Once removed, overload protection is not guaranteed The saddle is not included L (104) R1/2 12 SR Saddle (CA-B) (Option) R 4 13 B 30 A 24 Mount Base R1/ L SR Saddle (CA 10B) (Option) Mount Base R 4 9 LCR-B-5~KNS7 LCR-B-5KNS7(L, R) LCR-B-10KNS7(L, R) LCR-B-KNS7(L, R) LCR-B-30KNS7(L) LCR-B-KNS7(L, R) LCR-B-KNS7(L, R) Rated Capacity 5kN 10kN kn 30kN kn kn A 57 B See drawing upper left. Weight 4kg 4.5kg 19kg Physical quantity indication Bared at the tip 2-71 LCR-B-KNS7 LCR-B-S WGA-6B 2-161