FLOW METER ULTRASONIC-VOLTEX FLOW METER ASUSV SERIES IMPELLER FLOW METER ASIP80 SERIES IMPELLER FLOW METER ASSPX SERIES

Transcription

1 FLOW METER P.193 P.195 P.196 P.197 P.198 P.198 P.198 P.199 P.199 P.200 P.200 P.200 P.200 ULTRASONIC-VOLTEX FLOW METER ASUSV SERIES IMPELLER FLOW METER ASIP80 SERIES IMPELLER FLOW METER ASSPX SERIES INSERTION ELECTROMAGNETIC FLOW METER ASEX80 SERIES ULTRASONIC FLOW METER DOPPLER ULTRASONIC FLOW METER ASDX-25 STATIONARY ASPX-20 PORTABLE ASSX-30 PORTABLE ASSX-40 STATIONARY ULTRASONIC FLOW METER TIME DIFFERENCE ULTRASONIC FLOW METER ASISTT-D6000 (S/M/L) STATIONARY ASISTT-D7000 PORTABLE ASISTT-D9000 AFFORDABLE TYPE 192

2 FLOW METER / ULTRASONIC-VORTEX FLOW METER ASUSV SERIES ULTRASONIC-VOLTEX FLOW METER ASUSV SERIES THE WETTED PART IS MADE OF CORROSION-RESISTANT ALL-PLASTIC (ANTI-CORROSIVE RESIN), MAKING THE METER IDEAL FOR CHEMICAL SOLUTION LINES FOR CHEMICAL, STEEL, ELECTROLYSIS, SEMICONDUCTOR AND PURIFICATION FACILITIES. STABLE AND HIGHLY ACCURATE FLOW MEASUREMENT WITH AN ACCURACY OF +/-1.0% (RD). KARMAN VORTEX DETECTION USING ULTRASONIC SENSOR PROTECTED FROM THE EFFECTS OF MECHANICAL NOISES SUCH AS PIPE VIBRATION. VALVE TYPE CONNECTION METHOD ULTRASONIC-VOLTEX FLOW METER ASUSV SERIES FLANGED, WAFER VALVE PARTS SENSOR PARTS WETTED PARTS MEASUREMENT ACCURACY FLUID FLANGED mm WAFER mm FLANGED PVDF WAFER U-PVC, PVDF ±1% R.D U-PVC 0~ 55 C PVDF -10~100 C MAXIMUM WORKING 1.0 MPa (at normal temp.) FLUID PRESSURE TOTAL INTEGRATING / INSTANTANEOUS FLOW RATE DISPLAY / % FLOW RATE / RESET INTEGRATING FLOW RATE (The display is switched by a magnet from the outside.) 4-20 ma, TWO-WIRE, LOAD RESISTANCE: 300Ω ANALOG OUTPUT MAX. <OPEN COLLECTOR OUTPUT> INTEGRATING PULSE OUTPUT / ALARM OUTPUT UPPER AND LOWER LIMIT OUTPUT / ALARM OUTPUT Either can be selected. CASE Polycarbonate POWER SOURCE DC 24V ±10% AMBIENT PROTECTIVE STRUCTURE U-PVC 0~55 C, 5~80%RH PVDF -10~60 C, 5~80%RH IP 66 equivalent. (Avoid direct sunlight.) MEASURING (mm) MINIMUM FLOW RATE (m 3 /h) <MEASUREMENT ACCURACY: ±1.0%RD > KINEMATIC VISCOSITY x 10 6 m 2 /s (cst) MAXIMUM FLOW RATE (m 3 /h) FLOW RATE 0.8m/sec 1.6m/sec 2.4m/sec 3.2m/sec 4.0m/sec 5.0m/sec NOTES To maintain the measurement accuracy, provide a straight pipe of 10D on the upper-flow side and of 5D in the downstream. (D = Inside pipe diameter) 193

3 INSTALLATION EXAMPLE (WAFER) AV packing Flow meter body Flange Nut, washer Stud bolt Collar (centering jig) TIGHTENING TORQUE [N m] 20mm 25mm 40mm 50mm 80mm 100mm U-PVC PVDF ULTRASONIC-VORTEX FLOW METER ASUSV SERIES CONNECTION / FLANGED, WAFER JIS WAFER L2 FLANGED W1 W1 W2 W3 L2 W2 W3 Wiring port 2-G1/2 Wiring port 2-G1/2 H H φd2 φd2 L1 φd φd1 L1 φd φd1 P.C.D.C n-φe JIS (Unit: mm) WAFER FLANGED (JIS10K) mm L2 W1 W2 W3 φd2 L1 H φd1 φd L1 H φd1 φd C n e

4 FLOW METER / IMPELLER FLOW METER ASIP80 SERIES, IMPELLER FLOW METER ASSPX SERIES IMPELLER FLOW METER ASIP80 SERIES INSERTION TYPE USING SPECIAL FITTING. ALL THE WETTED PARTS ARE MADE OF CHEMICAL-RESISTANT PLASTIC (SO THAT THE METER CAN BE USED FOR SEA WATER LINES AND VARIOUS CHEMICAL SOLUTION LINES). VALVE TYPE IMPELLER FLOW METER ASIP80 SERIES ASIP81(P/Y/K) 15mm 80mm ASIP82(P/Y/K) 100mm 150mm CONNECTION METHOD SOCKET, FLANGED SENSOR BODY WORKING HI-PVC 50 C PP 60 C PVDF 90 C 1.0MPa WORKING PRESSURE IMPELLER PVDF SHAFT ZIRCONIUM, SILICON-CARBIDE BEARING RUBY O-RING FKM(EPDM) SPECIAL FITTING U-PVC, HI-PVC, C-PVC (See TABLE 1.) MEASUREMENT FLUID FLUID (EXCEPT HIGH VISCOSITY FLUID AND SLURRY) MAXIMUM WORKING 0 90 C FLOW RATE m/s (See TABLE 2.) ABILITY 1:45 MEASUREMENT ACCURACY ±1.5%(FS) POWER SOURCE DC6 24V (Consumption current: 8 ma) OUTPUT SIGNAL 3-WIRE, CURRENT SINKING PULSE (NPN) (20 ma Max.) CABLE 3-CON (3.6 m length) FITTING INSTALLATION Upper flow: 10D Min. Downstream: 5D Min. (D: Inside pipe diameter) TABLE 1 MAX. OPERATING FLUID PRESSURE AND FOR SPECIAL FITTING PRESSURE (MPa) TEMP. ( C) U-PVC HI-PVC 15mm 150mm 15mm 50mm C-PVC 65mm 150mm TABLE 2 MEASURING AND K-FACTOR (mm) FLOW RATE (m 3 /h) Min Max K-FACTOR (cc/pulse) ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ NOTES (1) The value of K-factor is only a reference value. (2) Obtain the maximum frequency for each size by calculation. Max. frequency = Max. flow rate / K-factor (Hz) (cc/s) (cc/pulse) IMPELLER FLOW METER ASIP80 SERIES CONNECTION / FLANGED, SOCKET JIS FLANGED JIS (Unit: mm) SOCKET FLANGED mm U-PVC/HI-PVC U-PVC/HI-PVC JIS 10K JIS 5K L H L H D L H D D d t n e D d t n e NOTES (1) Piping condition) It is recommended to secure a fitting installation section of 10D on the upper flow side and 5D in the downstream. (D = Inside pipe diameter) Wiring condition) For wire extension, it is recommended to use shielded wires. (2) For display of flow rate, an indicator is required separately. (3) The appearance and shape of assembled parts may slightly differ from the diagram depending on the sizes. (4) Note that the following fittings are not available: Socket, JIS10K flange HI-PVC/C-PVC (125 mm, 150 mm) JIS 5K flange HI-PVC (125 mm, 150 mm), C-PVC (80 mm 150 mm) 195

5 IMPELLER FLOW METER ASSPX SERIES CORROSION-RESISTANT FLOW METER FOR LOW FLOW RATES. COMPACT DESIGN IDEAL FOR PIPING IN MACHINERY. VALVE TYPE IMPELLER FLOW METER ASSPX SERIES CONNECTION METHOD ASSPX-3/8inch Rc 3/8 ASSPX-1/2inch Rc 1/2 ASSPX-3/4inch Rc 3/4 ASSPX-1inch Rc 1 PP, PTFE PP, PTFE (Acrylic) PVDF ZIRCONIUM, SILICON-CARBIDE RUBY FKM, (EPDM) FLUID (EXCEPT HIGH VISCOSITY FLUID AND SLURRY) BODY COVER ROTOR SHAFT BEARING O-RING MEASUREMENT FLUID MAXIMUM WORKING C WORKING PRESSURE 1.0MPa FLOW RATE See TABLE 1. MEASUREMENT ACCURACY ±1%(FS) POWER SOURCE DC 6 24V (Consumption current: 8 ma) OUTPUT SIGNAL 3-WIRE, CURRENT SINKING PULSE (NPN) (20 ma Max.) CABLE 3-CON (3.6 m length) TABLE 1 MEASURING AND K-FACTOR CONNECTION INSTALLATION POSTURE FLOW RATE (L/min) ABILITY K-FACTOR (cc/pulse) 3/8 inch PIPING IS HORIZONTAL AND SHAFT IS VERTICAL :1 0 0 OTHER CASES : /2 inch PIPING IS HORIZONTAL AND SHAFT IS VERTICAL :1 0 0 OTHER CASES : /4 inch PIPING IS HORIZONTAL AND SHAFT IS VERTICAL :1 0 0 OTHER CASES : inch PIPING IS HORIZONTAL AND SHAFT IS VERTICAL :1 0 0 OTHER CASES : NOTES (1) The value of K-factor is only a reference value. (2) Obtain the maximum frequency for each size by calculation. Max. frequency (Hz) = Max. flow rate (cc/s) / K-factor (cc/pulse) IMPELLER FLOW METER ASSPX SERIES CONNECTION / THREADED Rc Inch screw NC10 X 4 (PP) Bolt hole φ4.5 x 4 (PTFE) Flow direction φ8.0 Counterbore 5.0 x 4 For A-1 PTFE φ8.5 Counterbore 7.0 x 4 JIS (Unit: mm) SOCKET PTFE L H D D1 RC 3/ RC 1/ RC 3/ RC NOTES (1) For wire extension, it is recommended to use shielded wires. (2) For display of flow rate, an indicator is required separately. (3) The cover attachment method varies depending on the materials. In the case of PP, the cover is tightened using hexagon socket head cap screws (inch screws). In the case of PTFE, it is sandwiched between hexagon socket head cap screws and inch screws. See A

6 FLOW METER / INSERTION ELECTROMAGNETIC FLOW METER ASEX80 SERIES, ULTRASONIC FLOW METER DOPPLER ULTRASONIC FLOW METER INSERTION ELECTROMAGNETIC FLOW METER ASEX80 SERIES INSERTION TYPE USING SPECIAL FITTING. ALL THE WETTED PARTS ARE MADE OF CHEMICAL-RESISTANT PLASTIC (SO THAT THE METER CAN BE USED FOR SEA WATER LINES AND VARIOUS CHEMICAL SOLUTION LINES). VALVE TYPE INSERTION ELECTROMAGNETIC FLOW METER ASEX80 SERIES ASEX81 25mm~80mm ASEX82 100mm~150mm CONNECTION FLANGED, SOCKET SENSOR BODY HI-PVC (DETECTOR) ELECTRODE HASTELLOY C SENSOR HOUSING ALUMINUM O-RING EPDM, FKM SPECIAL FITTING U-PVC, HI-PVC FLUID TO BE GENERAL CONDUCTIVE LIQUIDS. The minimum conductivity must MEASURED be 20 μs/cm or higher. <Reference> Tap water μs/cm FLUID 0~50 C WORKING PRESSURE 1.0 MPa (See TABLE 1.) FLOW m/s (See TABLE 2.) ACCURACY ±1.0% (FS) POWER SOURCE DC12-24V (Consumption current: 250 ma) OUTPUT SIGNAL CURRENT SINKING PULSE (NPN) (Load capacity: DC 30V, 6 ma or less) CABLE 4-CON SHIELD LINE (Approx. 5 m) ELECTRIC WIRING PORT WATER RESISTANT CONNECTOR (Applicable wire dia.: Φ8 max.) PROTECTIVE STRUCTURE NEMA 4X (IP65 equivalent) NOTE During batch operation (for cumulative usage management of the fluid in particular), avoid using an insertion electromagnetic flow meter. TABLE 1 WORKING PRESSURE VS. P W FLANGED P.C.D.d φd H (mm) PRESSURE (MPa) 20 C 30 C 40 C 50 C TABLE 2 MEASURING AND K-FACTOR FLOW RATE (m 3 /h) K-FACTOR (mm) Min Max (cc/pulse) NOTES (1) The value of K-factor is only a reference value. (2) Obtain the maximum frequency for each size by calculation. Max. frequency = Max. flow rate / K-factor (Hz) (cc/s) (cc/pulse) INSERTION ELECTROMAGNETIC FLOW METER ASEX80 SERIES CONNECTION / FLANGED, SOCKET JIS H L t φd L JIS (Unit: mm) SOCKET FLANGED mm L H L JIS 10K JIS 5K D d t n e D d t n e H W P NOTES (1) Piping condition) It is recommended to secure a fitting installation section of at least 10D on the upper flow side and 5D in the downstream. (D = Inside pipe diameter) Wiring condition) For wire extension, use shielded wires. (2) For display of flow rate, an indicator is required separately. (3) The appearance and shape of assembled parts may slightly differ from the diagram depending on the sizes. (4) Note that the following fittings are not available for this flow meter: Socket, Flange (JIS10K/JIS5K) Material HI-PVC (125 mm, 150 mm), Material C-PVC, PVDF 197

7 ULTRASONIC FLOW METER DOPPLER ULTRASONIC FLOW METER ASDX-25 STATIONARY APPLICABLE TO VARIOUS SHAPES AND TYPES, INCLUDING DITCHES, OPEN CONDUITS, HORSESHOE-SHAPED, INVERTED TRAPEZOID-SHAPED AND SQUARE-SHAPED PIPES. INDEPENDENT FROM THE EFFECTS OF FOREIGN SUBSTANCES OR AIR BUBBLE. EQUIPPED WITH DC 4 20 ma OUTPUT, 4 RELAY CONTACTS. ULTRASONIC WATER LEVEL SENSOR THAT DELIVERS STABLE PERFORMANCE WITH NO MAINTENANCE (OPTIONAL). VALVE TYPE ASDX25 FLOW 6m/s 6m/s ACCURACY (FLOW RATE) ±2.00% (FS) or 0.05 m/s WATER LEVEL MEASUREMENT m(AGKU2000) 0.3 8m(MSP420) ACCURACY (WATER LEVEL) ±0.5%(FS) WORKING 10 C 50 C DISPLAY 4 20 CHARACTERS, LCD LEVEL INPUT DC 4 20mA OUTPUT DC 4 20 ma, RELAY CONTACT (4 CONTACTS) CABLE LENGTH 10m(MAX 30m*) BODY POLYCARBONATE (IP65) SENSOR POLYURETHANE/SUS (IP68) Power supply AC100V(AC200V*, DC24V*) WEIGHT APPROX. 1 kg ASPX-20 PORTABLE APPLICABLE TO VARIOUS SHAPES AND TYPES, INCLUDING DITCHES, OPEN CONDUITS, HORSESHOE-SHAPED, INVERTED TRAPEZOID-SHAPED AND SQUARE-SHAPED PIPES. INDEPENDENT FROM THE EFFECTS OF FOREIGN SUBSTANCES OR AIR BUBBLE. PORTABLE DESIGN SO THAT THE METER CAN BE USED IN VARIOUS PLACES. INTEGRATED WITH WATER LEVEL SENSOR, EASY TO INSTALL. VALVE TYPE ASPX20 FLOW 6m/s 6m/s ACCURACY (FLOW RATE) ±2.00% (FS) or 0.05 m/s WATER LEVEL MEASUREMENT 0 3m ACCURACY (WATER LEVEL) ±0.5%(FS) WORKING 10 C 50 C DISPLAY 4 20 CHARACTERS, LCD DATA LOGGER STANDARD 512 KB (MAX. 8 MB) OUTPUT RS232C (Dedicated software used) CABLE LENGTH 7m VALVE PARTS FRP (IP67) SENSOR POLYURETHANE/SUS (IP68) Power supply D BATTERY 8 (Operable up to 6 months.) WEIGHT APPROX. 2.5 kg 198

8 FLOW METER / ULTRASONIC FLOW METER DOPPLER ULTRASONIC FLOW METER, ULTRASONIC FLOW METER TIME DIFFERENCE ULTRASONIC FLOW METER ULTRASONIC FLOW METER DOPPLER ULTRASONIC FLOW METER ASSX-30 PORTABLE IMPROVED NOISE RESISTANCE DUE TO DFD FUNCTION. RECHARGEABLE TYPE THAT REQUIRES NO POWER SUPPLY. SMALL TO LARGE S CAN BE MEASURED BY A SINGLE UNIT. EASY OPERATION REQUIRING ONLY QUICK MOUNTING OF AND INNER DIAMETER INPUT. CAPABLE OF STORING UP TO 90,000 DATA POINTS. VALVE TYPE ASSX-30 MEASURING ± m/s ACCURACY ±1.0%(FS) APPLICABLE PIPE 12 3,000mmφ EXTERNAL OUTPUT DC 4-20 ma (Load resistance: 800 Ω) RS232C Interface POWER AC100V/AC200V, rechargeable battery Operation: 12 hrs (Charge: 8 hrs) DISPLAY Instantaneous/integrating flow rate C C NEMA 6 (IP67 equivalent) Clamp-on type 5 m cable (150 m Max.*) WEIGHT Approx. 4.9 kg PARAMETER SETTING Keypad entry ASSX-40 STATIONARY IMPROVED NOISE RESISTANCE DUE TO DFD FUNCTION. PARAMETERS CAN BE EASILY ENTERED FROM THE PANEL, ALLOWING FOR ATTACHMENT, REMOVAL AND RELOCATION. CAPABLE OF STORING UP TO 90,000 DATA POINTS. VALVE TYPE ASSX-40 MEASURING ± m/s ACCURACY ±1.5%(FS) APPLICABLE PIPE 12 3,000mmφ EXTERNAL OUTPUT POWER DISPLAY WEIGHT PARAMETER SETTING DC 4-20 ma (Load resistance: 1 KΩ or less) RS232C Interface Relay contact output* AC90-132V(50/60Hz)/AC V(50/60Hz) Switch select type DC12-18V* Instantaneous/integrating flow rate C C NEMA-4X (IP65 equivalent) Clamp-on type 6 m cable (150 m Max.*) Approx. 5.4 kg Keypad entry / Entry from PC using dedicated software 199

9 ULTRASONIC FLOW METER TIME DIFFERENCE ULTRASONIC FLOW METER ASISTT-D6000 (S/M/L) STATIONARY PARAMETERS CAN BE EASILY ENTERED FROM THE PANEL, ALLOWING FOR ATTACHMENT, REMOVAL AND RELOCATION. DEPENDING ON THE PIPE, 3 TYPES ARE AVAILABLE: ASISTT-D6000S (25 mm 200 mm) ASISTT-D6000M (250 mm 500 mm) ASISTT-D6000L (550 mm 3,000 mm) TYPE ASISTT-D6000(S/M/L) MEASURING ±0 15 m/s (positive/negative direction indicated) ACCURACY ±0.8%(FS) LINEARITY ±0.1%(FS) REPRODUCIBILITY ±0.2%(FS) APPLICABLE PIPE EXTERNAL OUTPUT S 25mm 200mmφ M 250mm 500mmφ L 550mm 3,000mmφ DC 4-20 ma (Load resistance: 1 KΩ or less) RS232C Interface Relay contact output* POWER DISPLAY WEIGHT PARAMETER SETTING AC90-132V(50/60Hz)/AC V(50/60Hz) Switch select type Instantaneous/integrating flow rate, flow velocity C C (240 C Max.*) NEMA-4X (IP65 equivalent) Clamp-on type 9 m cable (300 m Max.*) Approx. 5.4 kg Keypad entry / Entry from PC using dedicated software ASISTT-D7000 PORTABLE UNIQUE SIGNAL PROCESSING REDUCES THE EFFECTS OF FLUID CONDITIONS. RECHARGEABLE TYPE THAT REQUIRES NO POWER SUPPLY. EQUIPPED WITH BUILT-IN DATA LOGGER. IDEAL FOR PUMP CAPACITY CHECK AND BACK-UP OF EXISTING FLOW METER. TYPE MEASURING ACCURACY ASISTT-D7000 ±0 15 m/s (positive/negative direction indicated) ±0.8%(FS) DISPLAY Instantaneous/integrating flow rate, flow velocity C C (240 C Max.*) LINEARITY REPRODUCIBILITY APPLICABLE PIPE ±0.1%(FS) ±0.2%(FS) 25 3,000mmφ NEMA 6 (IP67 equivalent) Clamp-on type 5 m cable (300 m Max.*) EXTERNAL OUTPUT POWER DC 4-20 ma (Load resistance: 1 KΩ or less) RS232 interface AC100V/AC200V, rechargeable battery Operation: 8 hrs (Charge: 12 hrs) WEIGHT PARAMETER SETTING Approx. 5.0 kg Keypad entry ASISTT-D9000 AFFORDABLE TYPE LIGHTWEIGHT AND COMPACT EQUIPPED WITH NUMERIC KEYPAD, ALLOWING SETTINGS TO BE CONFIGURED USING THE MAIN UNIT (SENSOR). TYPE ASISTT-D9000 DISPLAY Instantaneous/integrating flow rate, flow velocity MEASURING ACCURACY ±0 12m/s ±1.0% (FS) C C (150 C Max.*) LINEARITY ±0.2% (FS) NEMA-4X (IP66 equivalent) REPRODUCIBILITY ±0.3% (FS) APPLICABLE PIPE 25 3,000mmφ EXTERNAL OUTPUT DC4 20mA POWER AC90V AC245V DC10V DC36V* WEIGHT PARAMETER SETTING Clamp-on type 9 m cable (300 m Max.*) Approx. 3.5 kg Keypad entry 200