Transcription

1 BULB SYSTEMS BULB SYSTEM ELECTRICAL SPECIFICATIONS System Model Input current Input Power Rated Initial Efficacy Watts Number (Amp) 120V - 277V (W) Lumens (LM) (LM/W)* HH-ILS-BP35-5K HH-ILS-BP55-5K HH-ILS-BP85-5K HH-ILS-BDS85-5K HH-ILS-BP100-5K HH-ILS-BDS100-5K HH-ILS-BP120-5K Lumen Maintenance (60Khrs) 70%-75% CRI >80 Color Temp. (Kelvin) 2720K K 5K Standard Color Average Lamp Life (Hours) 100,000 * NOTE: Bare Lamp specifications will vary from fixture test results; LM/W is based on tested Lamp Power. Reference "RELATIVE LUMEN OUTPUT CHART" and contact Fulham for proper Spectrophotocolormeter "Sphere" test procedures. BULB SYSTEM ELECTRICAL SPECIFICATION COMMON TO ALL GENERATORS Input Voltage 120V-277V EMI/RFI Compliance FCC Part 18-A Voltage Fluctuation Tolerance ±10% Sound Rating Class A Input Frequency 50/60 Hz Type 1 Outdoor Output Frequency <250K Hz Surge Protection** Yes (Reference hi-pot test footnote) THD < 10% Max. Remote Distance*** 4.5ft. (54 ) (Reference Wiring Footnote) Power Factor > 0.95 Wiring Plug-n-Play Connectors CERTIFICATIONS E Constant Wattage Output <5% Wire Rating 150 C 600V (Lamp Wire Shielded) Case Temp. < 65 C Electrostatic Discharge (ESD) IEC :Class 4 Operating Temp. Open Fixture 0 C to 50 C Electrical Fast Transient/Burst(EFT) IEC : Level 4 Operating Temp. Closed Fixture -20 C to 50 C Surge Immunity IEC : Class 4 **Surge Protection: Contact Fulham before conducting Hi-Pot test. ***Wiring: Do not modify wire type or length without contacting Fulham for assistance. No remote mount options are available for the Bulb System. Reference wire extensions under Lamp Advanced Features for available options. SYSTEM MODEL NUMBER EXAMPLE FOR BULB SYSTEMS HH HH = HIGHHORSE ILS B DS 200 5K ILS = INDUCTION LIGHTING SYSTEM B = BULB LAMP DS = DISC SYSTEM WATTS KELVIN TEMP. P = PROFILE Specify Kelvin when ordering. BALLAST 5K is standard stock color Rev Q

2 BULB SYSTEMS BULB SYSTEM SPECIFICATIONS Lamp Type Bulb Internal Inductor Type Hybrid Fluorescent All Prim ary Ignition Low Frequency Inductor Coupler Operating Temperature Range (Thermal Management) Induction Lam p Core Mounting Base 100 C C Am algam Lam p Tip Tem perature Range 55 C C Lam p Power Coupler 160 C C Bulb Convection or Conduction Lamp Operation Color Tem perature Fluctuation <10% LPW Fluctuation <10% Lamp Kelvin Temperature Options Kelvin Tem perature (Standard) 5000K Lim ited Stock (call Fulham for availability) 3500K, 4000K Special Factory Order (call Fulham ) 2700K, 3000K, 6000K, 6500K Kelvin Color Tem perature Tolerance ±300K Cold Start and Operation Systems Operating Tem perature (Closed Fixture) -40 C Freezer Operation Only (Call Fulham for Assistance) EMI Meets International Standard L Level FCC Non-Consum er units Com pliant FCC 47-CFR Part 18 Vibration Tests The HighHorse Induction lamp is designed to tolerate shock and vibration that w ould be expected in typical applications such as post top, bridge, roadw ay underpass or tunnel lighting. HighHorse Induction lamps have been tested under the follow ing conditions w ith no damage: -Shock - Lamps subjected to three (3) one-half w ave shocks of 10 ms duration at 20 g. -Vibration parameters adapted from ANSI C , American National Standard for Roadw ay Lighting Equipment - Luminaire Vibration, Section 5, luminaire vibration test. Start Freq. Amplitude End Freq. Amplitude 5Hz 1.5 G Hz 3.5 G 10Hz 3.5 G 30Hz 3.5G Sweep between 5 Hz and 30 Hz at Min/sweep (Linear) Duration: 100,000 cycles at 100% Total test tim e: 1:36:30 Care should be taken when m ounting ballast to m inim ize vibration UV UV (bare lam p-less with lens) 5uw/cm 2 * LPW is related to the temperature of Amalgam and Kelvin Temperature to maintain >90% output Rev Q

3 BULB SPECIFICATIONS BULB LAMP SYSTEM SPECIFICATIONS (Part II) Amalgam Hg. Amalgam Type High Quality Solid Pellet Amalgam Chart Lam p Type B35W B55W B85W B100W B120W Amalgam Type A A A A A Weight/ PC (mg) PCS Total Weight (mg) Content of Hg in % Pure Hg Weight (mg) Lamp Advanced Features Ultra-High Life 100,000hr Rated Lamp Technology Wide Range of Wattage Options 35W 120W Full Kelvin Color Range K Instant Start Flicker Free Operation Frequency Power Tuned Wattage to Ballast High Quality Phosphor Blends High CRI (Color Rendering Index) High Quality Solid Amalgam Pellet Ultra-Low Mercury Content (Encapsulated) Pre-Wired Lamp Input Connector Universal Heat Sink Mounting Compatible with Motion and Light Sensor Line Controls MADE IN AMERICA The Office of Energy Efficiency and Renewable Energy ( EERE ) at the US Department of Energy ( DOE ) has recently issued guidance relating to the Buy American Provisions of the Recovery Act. EERE issued the attached (I) Guidance on Manufactured Goods and Substantial Transformation for Financial Assistance Awards on May 24, 2010 ( Guidance ) and (ii) Memorandum of Decision granting a waiver of Section 1605 for Induction Lamps and Generators on August 11, 2010 ( Waiver ). The Guidance and Waiver are applicable to projects receiving financial assistance under the Recovery Act and are in effect until further notice from the DOE. Applying the terms of the Waiver, Fulham s induction lamps and generators are categorically exempt from the Buy American Provisions. Please use the matrix below in determining the applicability of the Buy American Provisions to the constituent parts provided by Fulham for New or Retrofit Induction Fixtures. Fulham Induction Lamps Exempt Under Waiver Fulham Induction Generators Exempt Under Waiver Fulham Retrofit Kit (Reflector and Mounting Kit only) Made in America The above determination does not apply to imported New or Retrofit Induction Fixtures (including the constituent housing, reflector, mounting kit and lens) supplied by customers or third parties. Each such item must be evaluated under the Recovery Act, Guidance and Waiver on a case by case basis by the customer or third party for compliance with the Buy American Provisions Rev Q

4 INRUSH / INDUCTANCE BULB INRUSH CURRENT System Model Number Watts Voltage Inrush Current Inrush Period HH-ILS-BP35-5K V 9.0A ĎĆĆBĆ Œ I I L[ {. t يي Yي V 9.0A ĎĆĆBĆ Œ I I L[ {. t ي ی Yي HH-ILS-BDS85-5K HH-ILS-BP100-5K HH-ILS-BDS100-5K V 14.0A ĐĆĆBĆ Œ V 14.0A ĐĆĆBĆ Œ HH-ILS-BP120-5K V 14.0A ĐĆĆBĆ Œ System Model Number Watts Voltage Inrush Current Inrush Period HH-ILS-BP35-5K V 18.0A DĆĆBĆ Œ I I L[ {. t يي Yي V 18.0A DĆĆBĆ Œ I I L[ {. t ي ی Yي HH-ILS-BDS85-5K HH-ILS-BP100-5K HH-ILS-BDS100-5K V 27.0A ĎĆĆBĆ Œ V 27.0A ĎĆĆBĆ Œ HH-ILS-BP120-5K V 27.0A ĎĆĆBĆ Œ NOTE: ALWAYS CONSULT A LICENSED ELECTRICIAN BEFORE INSTALLING ANY ELECTRICAL DEVICE. BULB LAMP INDUCTANCE Coupler Value 35W 55W 85W 100W 120W L (Inductance) 167.0µH 167.0µH 162.0µH 96.0µH 96.0µH Windings (Turns) Frequency Connected Method Room Ambient 250khz Ls 25 C As with all electronic equipment, Fulham Induction Systems have a peak current shortly after the mains is switched on; while this is a momentary condition it is important to calculate the total load during this peak current demand. It is advised to use C-type MCBs in lighting installations with electronic ballasts. If it is absolutely necessary to connect more than the specified maximum number of fixtures based on peak demand contact a Licensed Electrician and consider a relay in the wiring circuit to limit the number of activated fixtures at one time. All types of Inductance (Self/Mutual/Partial/Loop/Loop Mutual) are directly related to the number of magnetic fields around a conductor per amp of current; it requires special equipment to measure inductance. Fulham Retro-fit Engineering Services is equipped to measure and mitigate the effects of Inductance which ultimately can produce failure of the system when not considered in the design of an Induction fixture. All Fulham engineered systems are certified to operate properly relative to Inductance, Thermal, and overall fixture efficacy Rev Q

5 REMOTE MOUNT Bulb System can only be remotely mounted up to 4.5 ft. No remote mount options are available for the Bulb System. Reference wire extensions under Lamp Advanced Features for available options. Bulb Lamp Advanced Features EXTENSION WIRE P/N LENGTH INCHES FEET HHILPE " 0.3' HHILPE " 1.0' HHILPE " 3.0' ASSEMBLY VIEW SCALE 1:5 NOTE: Product is shipped as shown SCALE 1:3 LENGTH WIRE SHIELD FEMALE CONNECTOR TO BALLAST WIRE SPECIFICATIONS: V 18AWG MALE CONNECTOR TO LAMP NOTE: Standard Extension Wires HHILPE00007 available for Circular and Tubular Lamp systems only. Contact Fulham for assistance in engineering your custom wires options Rev Q

6 LUMEN MAINTENANCE (-30ºC) Lumen Output (Fc) Input Power (W) Lamp Amalgam Temp. ( C) (52ºC) MINUTES NOTE: Purpose of Lumen Maintenance Chart is strictly to show relation of the three variables over time. % RATED LUMENS SURVIVAL % ,000 40,000 60,000 80, ,000 OPERATING HOURS ,000 40,000 60,000 80, ,000 OPERATING HOURS Rated Lumen Maintenance Chart Cold Start Lumen Maintenance Chart HighHorse induction systems operate within a wide range of ambient; the chart is an example of a 100W induction system operated at extreme cold temperature. It is recommended if the system requires a cold start at -30 C that a thermal blanket be installed at the factory on the amalgam tip; this will ensure a consistent start and rapid stabilization of the lamp and lumen output. Note: Closed fixture example, actual performance varies with fixture types. Rated Lumen Maintenance is largely determined by operating temperature of the lamp and quality of lamp design; Fulham HighHorse induction systems are designed and manufactured with high quality tri-phosphors and solid amalgam to optimize the performance and rated life of the lamp. The above chart is intended to represent an average rated lumen output stated as a percentage of the initial lumen output over the rated life of the lamp. Operating the lamp within the temperatures specification will typically result in not less than 70% lumen output at 60Khrs. System Rated Life Chart System Rated Life varies with operating temperature and application. Fulham HighHorse induction generators are designed with high quality long lasting components and when operated at the rated Tc 65ºC expected life is 60Khrs with failure rate of 15% to 20%. Operating temperatures less than the rated Tc 65ºC can typically improve life expectancy and reduce failure rate Relative Lumen Output W ballast Relative Lumen Output Chart Lumen output is directly related t System Power and Amalgam Temperature; properly designed systems result in a stable lamp condition and maximum light output. All Fulham Engineered HighHorse Induction systems operate with less than a 15% validation over a wide range of Amalgam operating temperature (60ºC - 125ºC). Fulham Retro-fit systems are engineered for a maximum light output and improved life expectancy Relative Light Output System Power Amalgam Temperature ) Rev Q

7 TEMPERATURE TEST POINTS PLEASE NOTE: Induction lamps are fragile and require care when handling; DO NOT allow the glass to come in contact with metal objects. The amalgam glass can be easily broken DISC BALLAST BULB LAMP 13 2 PROFILE BALLAST Note: Test points 2 and 3 are on the side of the ballast; location is not precise. BULB INDUCTION SYSTEM TEMPERATURE CHART TEST POINT TEMPERATURE TEST POINTS: RATED TEMPERATURE MAX TEMPERATURE 1 BALLAST: TC < 65ºC (149ºF) 65ºC (149ºF) 2 BALLAST: SIDE 1 < 65ºC (149ºF) 65ºC (149ºF) 3 BALLAST: SIDE 2 < 65ºC (149ºF) 65ºC (149ºF) 4 BALLAST PLATE/MOUNTING LOCATION N/A N/A 5 BALLAST AMBIENT N/A N/A 6 LAMP BASE (HEAT SINK) 100ºC (212ºF) - 120ºC (248ºF) 120ºC (248ºF) 7 LAMP POWER COUPLER < 160ºC (320ºF) 200ºC (392ºF) 8 GLASS VESSEL AMALGAM TIP 55ºC (131ºF) - 125ºC (257ºF) 125ºC (257ºF) 9 LAMP AMBIENT < 80ºC (176ºF) < 100ºC (212ºF) 10 POWER COUPLER WIRE RATING < 140ºC (284ºF) 150ºC (302ºF) 11 GLASS VESSEL PLASTIC SLEEVE <150 C (302 F) 180 C (356 F) 12 GLASS MAX DIAMETER < 140ºC (284ºF) 180ºC (356ºF) 13 WIRE CONNECTOR < 105ºC (221ºF) 105ºC (221ºF) NOTE: TEMPERATURE MEASUREMENTS ARE RECOMMENDED TO BE AT THE RATED TEMPERATURE FOR BEST PERFORMANCE AND LIFE EXPECTANCY. LAMP AND GENERATOR TEMPERATURES MAY NOT EXCEED THE MAXIMUM OPERATING AMBIENT TEMPERATURE WHEN INSTALLED IN A FIXTURE. CONTACT FULHAM FOR APPROVED TEMPERATURE TEST PROCEDURE Rev Q

8 DIMENSIONS - LAMP X±.10" H±.10" W±.03" Bulb Lamp Model No. ĢĢǼHI ǼĘĊDJ DĦ ĢĢǼHI ǼĘDDJ DĦ ĢĢǼHI ǼĘÐDJ DĦ ĢĢǼHI ǼĘĈĆĆJ DĦ ĢĢǼHI ǼĘĈČĆJ DĦ H (in) 5.51 ĎBĆE ĎBĆE ĐBĈÐ ĐBĈÐ W (in) 2.27 ČBEČ ČBEČ ČBEČ ČBEČ ØX (in) 3.89 ÇBČĐ ÇBČĐ DBĈČ DBĈČ Input Wire L (in) 15 تو 15 تو 15 تو 15 تو 15 تو Contact Fulham for detailed drawings. * Subject to change. Contact Fulham for specific wire lengths Rev Q

9 DIMENSIONS - BALLASTS X.05" W±.03 H.10" L±.03 H±.03 Disc Ballast (White) Profile Aluminum Ballast (Black) Model No. ĢĢǼHĘǼĮ Í IJǼĘĠGĬ ÐD ĢĢǼHĘǼĮ Í IJǼĘĠGĬ ĈĆĆ Disc Ballast Size H (in) W (in) ØX (in) SMALL EBDČ تو Ĭ Ì ĖI I تو Input Wire L (in) تو 10 تو 10 Profile Ballast Model No. Size L W H Input Wire L (in) Output Wire L (in) ĢĢǼHĘǼĮ Í IJǼĘĠĨ ĊD SMALL ĎBĆĆ ĊBĎÐ ĈBDE 10 تو 10 تو ĢĢǼHĘǼĮ Í IJǼĘĠĨ DD SMALL ĎBĆĆ ĊBĎÐ ĈBDE 10 تو 10 تو ĢĢǼHĘǼĮ Í IJǼĘĠĨ ÐD MEDIUM ĐBĆĎ ÇBĈČ ĈBEĈ 10 تو 10 تو ĢĢǼHĘǼĮ Í IJǼĘĠĨ ĈĆĆ MEDIUM ĐBĆĎ ÇBĈČ ĈBEĈ 10 تو 10 تو ĢĢǼHĘǼĮ Í IJǼĘĠĨ ĈČĆ MEDIUM ĐBĆĎ ÇBĈČ ĈBEĈ 10 تو 10 تو Contact Fulham for detailed drawings. * Subject to change. Contact Fulham for specific wire lengths Rev Q

10 BULB HEAT SINK Part Number# HHHSABG120 Description Small Bulb Heat Sink Lamp Wattage Range 35W-120W " 6.57 TOP VIEW " 1.38 FRONT VIEW BOTTOM VIEW VIEW OF LAMP ASSEMBLY SCALE 1: Rev Q

11 BULB LAMP - ASSEMBLY 35W-120W Glass Vessel Vessel Collar Power Coupler Mounting Base Twist Lock Feature CLOSE OPEN ASSEMBLY STEPS: 1. Insert the Amalgam tip from the Glass Vessel into the opening inside the Power Coupler. 2. Slowly lower the Glass Vessel onto the Power Coupler. 3. Once the Glass Vessel touches the Twist Lock Feature on the Power Coupler then grasp the Glass Vessel by the Vessel Collar and twist clockwise while applying pressure downwards Rev Q