Operating instructions RC (RtF) Xtreme V2

Transcription

1 by Operating instructions 88025RC (RtF) Xtreme V2

2 2

3 Table of contents 1. Introduction Latest operating instructions Symbols Intended use Safety instructions Persons/Product Before commissioning During operation Outdoor flying locations Batteries General information LiPo batteries Miscellaneous Accident prevention Emergency stop Charging and installing battery Charging Installing the battery Installing propellers and guards Installing Removing FPV Camera and antenna Video TX Propeller Block Auto Stop Basic control Mode 2 Control Auto-flip Altitude hold Emergency auto level Remote OSD Menu Photo and Video modes Photo taking Video recording Start Stop Video channel selection - Automatic Video channel selection - Manual Xtreme V Transmitter Preflight checklist Status Indications Technical data Disposal General Batteries Declaration of Conformity FCC Note Product support Legal notes

4 1. Introduction Dear customer, Thank you for purchasing the RC EYE Xtreme V2! We hope you will enjoy your FPV experience and that the V2 will become a favorite flyer whether it s your first drone or just a new drone you are adding to the collection. For the best experience please read and familiarize yourself with the V2 by reading through this document. It will help you have a full understanding of preparing for your first flight and also answer any questions you might have. This product complies with the applicable National and European standards and regulations. We kindly request the user to follow the operating instructions, to preserve this condition and to ensure safe operation! These operating instructions relate to this product. They contain important notices on commissioning and handling. Please take this into consideration when you pass the product on to third parties. Please keep these instructions for future reference! All company names and product designations contained herein are trademarks of the respective owners. All rights reserved. We wish you a great deal of enjoyment with your new RC Logger product! 2. Latest operating instructions Please download the latest version of the operating instructions from our website at Navigate to the product page and open the Downloads tab. Click on Operating instructions to start the download. 3. Symbols BLUE provides you with additional useful information, and highlights important facts. RED stands for danger and alert. Read these sections always to avoid accidents and product damage. GREEN stands for good practice, protecting your product from damage. 4. Intended use The Xtreme V2 is a model quad copter solely designed for private use in the model making area and the operating times associated with this. The Xtreme V2 is not suitable for other types of use, including commercial applications. Any use other than the one described can damage the device. Moreover, this involves dangers such as short circuit, fire and electric shock, etc. Observe the safety information under all circumstances! The product must not become damp or wet. This product is not a toy and not suitable for children under the age of 14. For safety and approval purposes, you must not rebuild and/or modify this product. If you use the product for purposes other than those described above, the product may be damaged. In addition, improper use can cause hazards such as short circuiting, fire, electric shock etc. Read the instructions carefully and keep them. Make this product available to third parties only together with its operating instructions. 4 Introduction

5 5. Safety instructions Read the operating instructions carefully and especially observe the safety instructions. If you do not follow the safety instructions and information on proper handling in this manual, we assume no liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/guarantee. 5.1 Persons/Product The device is not a toy. Keep it out of the reach of children and pets. Do not leave packaging material lying around carelessly. These may become dangerous playing material for children. If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. Safe operation can no longer be guaranteed if the product: is visibly damaged, is no longer working properly, has been stored for extended periods in poor ambient conditions, or has been subjected to any serious transport-related stresses. The product must not become damp or wet. The Xtreme V2 uses delicate electronic components which are sensitive to temperature fluctuations and are optimised for a particular temperature range. Observe the operating temperature range given in the technical data. Do not place the product under any mechanical stress. Handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product. Important note! Operating the model may cause damage to property and/or individuals. Therefore, make sure that you are sufficiently insured when using the model, e.g. by taking out private liability insurance. If you already have private liability insurance, verify whether or not operation of the model is covered by your insurance before commissioning your model. Note: Some EU countries require insurance for all flight models! Observe the laws concerning the use of cameras for surveillance purposes. Observe the privacy of others at flight recordings. Do not film people without their prior consent. Always comply with the respective applicable laws and provisions. 5.2 Before commissioning Before every flight, check the functional reliability of your model and the transmitter. Watch out for any visible damage such as defective plug connections or damaged cables and wires. All moving parts of the model must run smoothly but should not have any play in their bearings. Before each operation check the correct and secure position of the propellers. Charge the flight battery. Always switch on the transmitter first before powering on the Xtreme V2. Set the throttle to zero before powering on the Xtreme V2. The motors might run unintentionally! 5.3 During operation When the motors are running, make sure that neither objects nor body parts are in the rotating and suction area of the propellers. Do not take any risks when operating the model! Your own safety and that of your environment is solely down to you being responsible when dealing with the model. Improper operation may cause serious injury and property damage! Therefore make sure to keep a sufficiently safe distance to persons, animals or objects during operation. Select an appropriate location for the operation of the Xtreme V2. Fly the Xtreme V2 only if your ability to respond is unrestricted. The influence of tiredness, alcohol or medication can cause incorrect responses. Safety Instructions 5

6 Do not direct your model towards spectators or yourself. Motor, electronics and flight battery may heat up during operation. Wait 5 to 10 minutes before recharging or replacing the flight battery. Never switch off the transmitter while the Xtreme V2 is in use. After landing, always disconnect the flight battery first. Only then may the transmitter be switched off. In case of a defect or a malfunction, remove the problem before using the Xtreme V2 again. Never expose the Xtreme V2 or the transmitter to direct sunlight or excessive heat for an extended period of time. In the case of a severe crash (e.g. from a high altitude) the electric gyro sensors can be damaged and/or misadjusted. Therefore, full functionality must be tested before flying again without fail! In the event of a crash, the throttle should be immediately set to zero. Rotating propellers may be damaged if they come into contact with obstacles. Before flying again, these should be checked for possible tears or breakages! Observe the warn/safety signals emitted by the Xtreme V2 at all times to avoid damage. 5.4 Outdoor flying locations Always and only operate the Xtreme V2 in a designated RC flying area. Stay away from power lines, cellphone towers and other sources of potential interference, and restricted areas. Never fly the Xtreme V2 above or near people. Contact a local RC club nearby to find out more about designated and approved flying areas. 5.5 Batteries General information Correct polarity must be observed while inserting/connecting batteries. Remove the flight battery from the Xtreme V2 after every flight. Remove the battery from the transmitter if you do not use it for a longer period of time. Batteries must be kept out of the reach of children. Do not leave the batteries lying around. Batteries must not be dismantled, short-circuited or exposed to fire LiPo batteries After the flight, the LiPo flight battery must be dis-connected from the Xtreme V2. Lithium is a highly reactive chemical element with a high energy density. In the case of overcharging, the LiPo rechargeable battery packs might catch fire or even explode. Therefore, LiPo rechargeable battery packs must always be put on a fire-proof surface for charging and the charging process must be supervised. In no case must the maximum permissible battery pack temperature of +60 C be exceeded. Otherwise the rechargeable battery may explode! Caution: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. Hazards of LiPo flight batteries Do not leave the LiPo flight battery connected when you do not use it (e.g. during transport or storage). Otherwise, the LiPo flight battery may be fully discharged. This would destroy it and render it unusable! There is also a danger of malfunction due to 6 Safety Instructions

7 interference. The rotors could start up inadvertently and cause damage or injury. Rechargeable LiPo batteries are very susceptible to moisture due to the chemicals they contain! Do not expose them to moisture or liquids. Risk of explosion! Do not expose the charger or LiPo flight battery to high/low temperatures or to direct solar radiation. When handling LiPo batteries, observe the special safety information of the battery manufacturer! Never charge the LiPo flight battery immediately after use. Always leave the LiPo flight battery to cool off first (at least 5-10 minutes). Only charge intact and undamaged batteries. If the external insulation of the rechargeable battery is damaged or if the rechargeable battery is deformed or bloated, it must not be charged. In this case, there is immediate danger of fire and explosion! Never damage the exterior of a LiPo flight battery. Never cut the covering foil. Never stab any LiPo flight batteries with pointed objects. As the charger and the rechargeable LiPo flight battery both heat up during the charging procedure, it is necessary to ensure sufficient ventilation. Never cover the charger or the LiPo flight battery! Of course, this also applies for all other chargers and rechargeable batteries. Remove the LiPo flight battery that is to be charged from the model and place it on a fire-proof support (e.g. a plate). Keep a distance to flammable objects. Disconnect the LiPo flight battery from the charger when it is fully charged. Chargers may only be operated in dry rooms. The charger and the LiPo flight battery must not become damp or wet. Never take the rechargeable battery apart! The rechargeable battery may not be subjected to any mechanical strain! The contacts may not be short-circuited, as there is danger of fire and explosion! Do not expose rechargeable batteries to fire, as there is a risk of explosion! Keep rechargeable LiPo batteries away from children. Store rechargeable batteries in a dry, cool place. If a rechargeable battery is deformed or damaged during a crash, it must no longer be used. The same applies for swollen rechargeable batteries, or rechargeable batteries with other visible deformation or leaks. Do not attempt to charge such rechargeable batteries! Danger of fire and explosion! Dispose of such rechargeable batteries in an ecologically sound fashion. The general hazard notices for handling batteries and rechargeable batteries also apply to rechargeable LiPo batteries. Total discharge Since discharging below 3.0 V per cell would lead to permanent damage of the rechargeable battery pack, this total discharging is to be prevented as far as possible. For safety reasons, programmable cruise controls/flight control systems should be set in such a way that the undervoltage detection has already responded before a voltage of 3.0 V per cell is reached (e.g. 3.2 V). Alternatively, optical undervoltage displays are also recommended. Correct dimensioning As the current drawn rises, the battery pack warms and the usable capacity is lowered. The ideal operating temperature during discharge is between +20 and +40 C and must not exceed +60 C even under extreme load. The maximum short-time discharge current is stated in the technical data sheets or can be read directly from the battery pack. The value C always refers to the capacity value of the respective battery pack. Example: A battery pack with a capacity of 2100 mah and 20 C can be dis-charged with 2100 ma x 20 = 42 A maximum. However, the maximum permissible continuous current is clearly lower. If there are no precise manufacturer s specifications, the battery pack should not be discharged with more than approx. 50 % of the maximum permissible surge current over a long term. Safety Instructions 7

8 5.6 Miscellaneous Consult an expert when in doubt about operation, safety or connection of the device. Maintenance, modifications and repairs are to be performed exclusively by an expert or at a qualified shop. If you have questions which remain unanswered by these operating instructions, contact our technical support service or other technical personnel. See 28. Product support on page Emergency stop When the Xtreme V2 enters an emergency situation, a red LED on the flight controller will flash with a solid lit orange LED next to it (see illustration below). 6. Accident prevention We strongly advise you to refrain from stunts until you master the Xtreme V2 in normal flying conditions. The best learning experience is provided by pilots who have experience in flying this type of aircraft. In case of an emergency, press the Power / Emergency button (gray colored button) on top of the Xtreme V2, or the ARM / Emergency button (red colored button) on the transmitter. Careless operation can cause serious damage and injury. Observe the following: Only fly the Xtreme V2 outdoors during good weather conditions. Do not fly the Xtreme V2 during adverse weather (rain, snow, strong winds, etc.). Do not fly without having covered the electronics (canopy). Ensure no moisture enters the body. Keep a sufficient clearance area during flight. Do not fly the Xtreme V2 in the vicinity of people and animals. Warning! You can only disarm the Xtreme V2 when not flying. 8 Accident Prevention

9 8. Charging and installing battery Warning! For your own safety, remove the flight battery whenever you are asked to do so. The charger only allows charging 1 battery at one time. Fully charge the flight battery before you fly and the transmitter battery when necessary. 1. Connect the charger s USB wire to a suitable power source (input current min. 4.5 A). Two LED indicators on the charger light up (2 LEDs means 2S). 2. The default charging mode is set for 2S batteries. If you wish to charge a 3S flight battery (sold separately), press the 2S/3S button on the charger to toggle between 2S/3S charging modes. 3. Charge the batteries as illustrated below: 8.1 Charging Use the supplied Xtreme V2 battery charger (89155RC) to charge the batteries. Read the charger s operating instructions before using it. Flight battery Transmitter battery Charging port for Flight battery (with push cover) LED indicator Charging port for Transmitter battery 4. Observe the indicator lights on the charger while charging: Charging 2S mode (default) 3S mode 2S / 3S selection Flight and transmitter batteries are provided. Fully Charged / without battery Solid red Solid blue Solid red Solid blue Battery for Xtreme V2 (Flight battery) Battery for transmitter Charging And Installing Battery 9

10 F-mode ALT-hold VIDEO FLIP 8.2 Installing the battery Install the flight battery as illustrated in the following sequence of diagrams. Fasten velcro strap Push the battery all the way in Close canopy, and make sure it is tightly locked in place Open the battery compartment as shown. Connect the transmitter battery and place it into the battery compartment, then replace the battery compartment cover. 10 Charging And Installing Battery

11 9. Installing propellers and guards Warning! Remove the flight battery before you install propellers and guards! Propeller installation Tightening direction Tightening direction Overtightening will irreversibly damage the thread in the propeller hub. In this case you must immediately replace the propeller! Both threads and bolts of each propeller mount / propeller must be in perfect condition Spinning mark on Black color propeller Spinning mark on Black color propeller 9.1 Installing Only tighten the propellers by hand and little force to avoid damage. The motors are reverse threaded. Propellers are tightened by turning them in the reverse direction of the arrow mark on propeller (indicator of spinning direction of motor). 1. Install a propeller on each motor by following the propeller diagram to the right. There is a spinning direction marking on each propeller. If propellers are installed incorrectly, the Xtreme V2 will not fly and may behave erratically. 2. Install a propeller guard on each side as shown on the bottom right. 9.2 Removing Loosen the propeller by hand and pull it off the shaft. If the propeller sits too tight, slide the supplied hex tool onto the hex portion of the motor, then loosen the propeller while countering with the hex tool. Tightening direction Spinning mark on White color propeller Propeller guard installation Tightening direction Spinning mark on White color propeller Installing Propellers And Guards 11

12 10. FPV Camera and antenna Remove the camera s protective cover before use. The FPV antenna is pre-installed (see below illustration). 11. Video TX Real time video transmission is possible via compatible FPV goggles or FPV receivers. Read the instructions supplied with the goggles or FPV receivers before you use them. 12. Propeller Block Auto Stop If propellers hit an object or the flight controller registers increased resistance, the motors will automatically be shut off. This ensures safety and keeps damage to a minimum should the Xtreme V2 hit an object. MicroSD card slot VTx antenna The FPV camera s tilt angle can be adjusted manually. You can rotate upwards by 35 degrees, and downwards by 60 degrees. To re-engage the motors proceed as follows: 1. Disarm the Xtreme V2 by pressing the ARM button on remote control. 2. Turn off the Xtreme V2 by pressing the Power button on top of the Xtreme V2. 3. With the Xtreme V2 turned off, you can safely inspect it for damage. 4. If no damage was caused, turn it back on by pressing the Power button on top of the Xtreme V2. 5. Arm the Xtreme V2 by pressing the ARM button on the transmitter. 12 Fpv Camera And Antenna

13 13. Basic control Study below diagrams before operating the Xtreme V2. Manual channel button (beneath the hatch) Canopy LEDs inside LEDs inside TOP Power button / emergency button BOTTOM Manual channel button Micro USB port SIDE FPV camera with adjustable angle FRONT MicroSD card slot BACK Video TX antenna Basic Control 13

14 ALT-hold Scan (Auto video channel scan) Rudder trim TFT monitor Power on indicator Aileron trim Menu + (manual band selection) (manual channel selection) F-mode VIDEO Video Throttle / Rudder Strap mount Arm/Disarm button / emergency button Aileron / Elevator Flight mode 1. Beginner 2. Sport 3. Sport acro 4. Expert FLIP Flip On / Off Elevator trim Altitude hold/ Bind Video out To avoid any misbehavior of the Xtreme V2, and as a common safety practice, always follow the sequence: Powering ON: First power ON the transmitter, then power ON the Xtreme V2. Powering OFF: First power OFF the Xtreme V2, then power OFF the transmitter. 14 Basic Control

15 14. Mode 2 Control Arm/Disarm button / emergency button Mode 2 Control 15

16 15. Auto-flip Only available for Beginner, Sport and Sport Acro modes Only perform flips outdoors in an open space environment. Performing flips in a small area can cause damage and/or accidents. VIDEO When flip is activated front LEDs are lit solid light blue. FLIP 1. Press the Flip button on the transmitter once to enter flip mode. A short double beep is emitted and all LEDs on the transmitter will give a short blink; the front LED on the Xtreme V2 is lit solid light blue. 2. Give stick input for flip direction. See illustrations to the right 3. The Xtreme V2 flips. Note: The Xtreme V2 flip mode has a safety timeout feature. If after you pressed the Flip button you do not move the Aileron / Elevator stick within 2 seconds, the Xtreme V2 will exit flip mode and return to the previous flying mode. 16 Auto-flip

17 16. Altitude hold Only available for Beginner and Sport modes Pressing the ALT-Hold button toggles the altitude hold function on/off. F-mode 17. Emergency auto level In expert mode (auto level disengaged) you have an emegergency auto levelling feature available. If at any time during practicing in this mode you lose orientation or control over your Xtreme V2 you can engage the auto level feature to assist you in regaining control. To engage the auto level feature in flight in expert mode, hold down the flight mode button F-mode on the transmitter for more than 0.5 s. Auto level remains enganged as long as you hold down the flight mode button. Release the flight mode button to disengage auto level. ALT-hold If Alt-Hold is activated, the colour of the LEDs on the front arms alternatingly change between orange and the flight mode color every second. Above illustrated example: Green front LEDs designates beginner mode. When Alt-hold is activated, the front LEDs change every second as follows: Orange > Green > Orange > Green Altitude Hold 17

18 18. Remote OSD Menu 19. Photo and Video modes 19.1 Photo taking To take a photo, press the video button once quickly. Each taken photo is confirmed by a double beep Video recording Start To start video recording, long press the video button. Start of recording is confirmed by a single beep. The recording notification timer on the 4.3 monitor fades in. Transmitter battery level Video signal strength Receiver channel Frequency channel Stop To stop video recording, long press the video button. Stop of recording is confirmed by a single beep. The recording notification timer on the 4.3 monitor fades out. Recording duration 18 Remote Osd Menu

19 20. Video channel selection - Automatic Your Xtreme V2 comes out of the box already bound to the transmitter. Once transmitter and Xtreme V2 are powered on and you do not see the live feed image on the transmitter screen after a few seconds start the auto channel scan. Hold down the SCAN button on the transmitter for a short moment then release it. The video receiver system will automatically scan and find the current band and channel that your Xtreme V2 is on and bind. Important note: sometimes Auto channel scan will connect to a neighboring band/channel. This can limit video range and reception. If you experience either of these limitations please refer to chapter 21. Video channel selection - Manual on page Video channel selection - Manual To manually change the channel/band proceed as described in the following chapters Transmitter 1. Press the scan button SCAN to display the current channel/band. 2. Press the + button on the transmitter to change the frequency band. Press the button to change the video channel. Cycle until you find the frequency you wish to use. 3. The channel/band is automatically saved when you stop cycling. Allow a short amount of time for the saving procedure to complete. 22. Preflight checklist Before turning on the transmitter and Xtreme V2, please run through below checklist: Are the propellers installed in correct orientation? Are the propellers secured and undamaged? Are the batteries in good condition and fully charged? Is the flight battery properly secured? Is the battery door properly closed? Is a microsd card installed (in case of using on board recording)? 21.1 Xtreme V2 1. Turn Xtreme V2 and transmitter off. 2. Remove the video transmitter hatch to get access to the manual channel button. Also refer to chapter 13. Basic control on page Turn Xtreme V2 and transmitter on. 4. Quickly press the button. The current band and channel will be displayed in the top right corner of the transmitter screen. 5. Hold down the button for about 1.5 seconds until the channel flashes on the screen. 6. Repeatedly press the button to cycle through the available channels/bands until the frequency you wish to use is displayed. The channel/band is automatically saved when you stop cycling. Allow a short amount of time for the saving procedure to complete. Video Channel Selection - Automatic 19

20 23. Status Indications The following reference charts are your quick guide to functions, LED and beeping indications. Main Functions F-mode Beginner Sport Sport acro Expert Auto flip Yes Yes Yes No Auto level Yes Yes Yes No Alt. hold Yes Yes No No Alarm Functions Alarms Description Indication Alarm/Error Any abnormal situation about Xtreme V2 Xtreme V2 Front and rear LEDs blinking white and swapping with current flight mode s LED color. Example: Beginner mode Transmitter -- Description Auto level with 11 degree limit Front: Green Rear: Red Auto level with 18 degree limit Front: Blue Rear: Red No angle limit. Manual flips and rolls are allowed. Front: Magenta Rear: Red No angle limit. Alt. hold not available. Rates are high. Front: Yellow Rear: Red Battery low Low: Need to proceed landing Extremely low: Must land immediatelty Front and rear LEDs blinking red and swapping with current flight mode s LED color. Example: Beginner mode All LEDs blinking and buzzer beeping LED indication Drone Remote LED 2 solid LED 3 solid LED 3 blinks LED 4 solid Signal loss -- All LEDs blink fast: Yellow-Blue-Yellow- Blue and swapping with current flight mode s LED color. Buzzer beeps: 0.5s ON 0.5s OFF Example: Beginner mode Status Indications

21 Additional Functions Additional functions Description Xtreme V2 Alt. Hold See chapter Alt-hold Front LEDs: Alternating flashing of flight mode color and orange. Example: Beginner mode ARM / DISARM Arm: allows the Xtreme V2 to take off Disarm: prevents the Xtreme V2 from taking off accidentally Indication -- Arm: Transmitter -- All LEDs on & long beep for 1s Back to display flight mode status Auto flip Press auto flip button: Xtreme V2 waits for 2 seconds for one of the four flip direction commands from Aileron/ Elevator stick. If stick is moved, the Xtreme V2 will make a short jump, then flips in commanded direction, auto levels again after the flip and exits the flip function. If stick is not moved in 2 seconds the Xtreme V2 will exit flip function and back to its previous state. If flip is not completed successfully (crash, hit a tree) then the Xtreme V2 will exit the function by time out (3 sec.). Front LEDs are lit solid blue while drone is in flip mode and returns to flight mode color after the flip. Flip mode: Continuous beeping and blinking with all LEDs until flip is finished. Disarm: All LEDs on and off & 2 short beeps Back to display flight mode status Photo Takes a single snapshot -- Double beep Video Start/Stop video recording -- Single beep for Start/Stop Status Indications 21

22 24. Technical data Xtreme V2: Power supply V, 2S Lipo 7500 ma (3S supported) Flight time... max. 10 min. (times may vary depending on style and environmental conditions) Camera... HD, 30 fps Memory card... microsd, max. 128 GB Operating temperature to +104 F (0 C to +40 C) Operating environment... Dry weather conditions Wind conditions... No wind, light to mild wind Frame size mm Dimensions x x 64.5 mm Weight g (with flight battery, without propeller guards) 240 g (without flight battery, without propeller guards) Transmitter: Screen Frequency GHz DSSS/FHSS Video receiver... Built-in, 5.8 GHz Transmission power mw Transmission distance... max. 150 m (free field) Channels... 8 Dimensions x x 95.5 mm Weight g (with flight battery) 295 g (without flight battery) Xtreme V2 Video transmitter: Frequency GHz Channels Transmission power mw Transmission distance... max. 150 m (line of sight) Frequency Band Values (MHz) A 5865, 5845, 5825, 5805, 5785, 5765, 5745 B 5733, 5752, 5771, 5790, 5809, 5828, 5847, 5866 F 5740, 5760, 5780, 5800, 5820, 5840, Technical Data

23 25. Disposal 25.1 General In order to preserve, protect and improve the quality of environment, protect human health and utilise natural resources prudently and rationally, the user should return unserviceable product to relevant facilities in accordance with statutory regulations. The crossed-out wheeled bin indicates the product needs to be disposed separately and not as municipal waste Batteries The user is legally obliged (battery regulation) to return used batteries and rechargeable batteries. Disposing used batteries in the household waste is prohibited! Batteries/ rechargeable batteries containing hazardous substances are marked with the crossed-out wheeled bin. The symbol indicates that the product is forbidden to be disposed via the domestic refuse. The chemical symbols for the respective hazardous substances are Cd = Cadmium, Hg = Mercury, Pb = Lead. You can return used batteries/ rechargeable batteries free of charge to any collecting point of your local authority, our stores or where batteries/ rechargeable batteries are sold. Consequently you comply with your legal obligations and contribute to environmental protection! 26. Declaration of Conformity Manufacturer: CEI Conrad Electronic International (HK) Limited License holder: CEI Conrad Electronic International (HK) Limited Address: 18th Floor, Tower 2, Nina Tower, No. 8 Yeung Uk Road, Tsuen Wan, New Territories, Hong Kong Importer: Conrad SE, Klaus-Conrad-Str. 1, D Hirschau We declare on our own responsibility, that the product: Product description: RC EYE Xtreme V2 Model: 88025RC CE marking on product: Hongkong, 01 August 2017 Place and date of issue CEI Conrad Electronic International (HK) Limited 18th Floor, Tower 2, Nina Tower, No. 8 Yeung Uk Road, Tsuen Wan, New Territories, Hong Kong Manufacturer/Authorized representative name and signature Disposal 23

24 27. FCC Note Caution: This device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or change to this equipment. Such modifications or change could void the user s authority to operate the equipment. This radio transmitter (identify the device by certification number or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. The device has been evaluated to meet general RF exposure requirement. To maintain compliance with FCC s RF exposure guidelines, this equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. 28. Product support Visit or call for product support. Additionally, visit our Online Ticket System at for any RC Logger inquiry. 29. Legal notes These operating instructions are published by CEI Conrad Electronic International (HK) Limited, 18th Floor, Tower 2, Nina Tower, No. 8 Yeung Uk Road, Tsuen Wan, New Territories, Hong Kong. All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. The operating instructions reflect the current technical specifications at time of print by CEI Conrad Electronic International (HK) Limited 88025RC_v2_1217_02_m_jh_en_(1) 24

25 25

26 26

27 27

28 28