LOW VOLTAGE ELECTRICAL MACHINES

Transcription

1 PROGRAM of the XII. International Conference on LOW VOLTAGE ELECTRICAL MACHINES Šlapanice, Czech Republic October 15 th 16 th, 2012 ORGANIZERS: TECHNICALLY SPONSORED BY:

2 LVEM - Committees General Chairs Hájek Vítězslav Skala Bohumil Vorel Pavel Richter Aleš Záskalický Pavol Miksiewicz Roman Program Chair Skalka Miroslav Organizing Chairs Cipín Radoslav Kurfürst Jiří Mach Martin Šmídková Alena (ZCU Pilsen, CZ) (TUL Liberec, CZ) (TUK Košice, SK) (STU Gliwice, PL)

3 Topics The main objective of the conference is to present and identify recent achievements and trends in the field of low voltage electrical machines, drives and power electronic, their improvement level and to discuss their attendant problems and implications in following topics. Electrical Machines & Equipment - DC Machines - Induction Machines - Permanent Magnet Synchronous Machines - Reluctance and Switched Reluctance Machines - Linear Machines, Levitation - Micro and Nano Machines - Electrical Equipment - Special Electrical Machines & Equipment - Piezo and Electrostatic Actuators - Design and Optimization - Electric, Thermal, Mechanical and Electromagnetic Field Computation - Modeling and Simulation - Thermal, Acoustic Noise and Vibration - Losses, Efficiency, Heating, Cooling - Monitoring, Diagnostics and Maintenance - Electromagnetic Compatibility - Education in Field of Electrical Machine Electrical Drives & Power Electronic - Industrial Electronics and Power Converters - Electrical Drives - Electrical Traction - Electrical Vehicles, Hybrid Drives - Usage of Electrochemical Power Sources - Application of Hydrogen Fuel Cells - Power Systems and Renewable Energy - Mechatronics - Factory Automation and Industrial Informatics - Sensors & Actuators - Signal Processing &Computational Intelligence - Electromechanical Systems Simulation & Control Theory - Education in Field of Electric Drives & Power Electronics

4 Conference program October 15 th, :15 09:00 Breakfast 08:00 11:30 13:30 18:00 Registration 09:00 09:10 Conference Opening prof. Ing. Vítězslav Hájek, CSc. 09:10 09:30 Ministry of Industry and Trade Ing. Miroslav Chlumský 09:30 09:45 CVVOZE project presentation prof. RNDr. Vladimír Aubrecht, CSc. 09:50 10:30 Company presentation I SVS FEM s.r.o. AREMAG motor test s.r.o. Chair: prof. Ing. Vítězslav Hájek, CSc. 10:30 11:50 Coffee Break 10:50 11:50 Company presentation II ATAS elektromotory Náchod a.s. Kollmorgen Siemens Electric Machines s.r.o. Chair: prof. Ing. Vítězslav Hájek, CSc. 12:00 13:30 Lunch 13:30 14:00 Issuing of the tax documents 14:00 15:00 Session S1 Induction machines; Permanent magnet synchronous machines Chair: doc. Ing. Bohumil Skala, Ph.D. Session S2 Modeling and simulation; Mechatronics; Industrial electronics and power converters Chair: doc. Ing. Pavel Vorel, Ph.D. 15:00 15:20 Coffee Break 15:20 16:20 Session S3 Permanent magnet synchronous machines; Design and optimization; Modeling and simulation Session S4 Losses, efficiency, heating, cooling; Electric, thermal, mechanical and electromagnetic field computation, Special electrical machines and equipment; Electrical vehicles, hybrid drives Chair: prof. Ing. Pavel Záskalický, CSc. Chair: prof. Ing. Aleš Richter, CSc. 16:20 17:50 Poster Session Thermal, acoustic noise and vibration; Modeling and simulation; Induction machines; Sensors and actuators; Education in field of electric drives and power electronics; DC machines; Losses, efficiency, heating, cooling; Power systems and renewable energy; Electric drives; Special electrical machines and equipment; Industrial electronics and power converters Chair: Ing. Roman Miksiewicz, Ph.D. 18:00 02:00 GALA DINNER

5 Conference program October 16 th, :15 09:00 Breakfast 09:00 10:00 Issuing of the tax documents 10:00 10:30 Brno University of Technology - presentation doc. Ing. Pavel Vorel, Ph.D. 10:30 10:50 Conference Closing prof. Ing. Vítězslav Hájek, CSc. 11:00 12:30 Lunch

6 Session program Session S1 14:00 15:00 Induction machines; Permanent magnet synchronous machines Chair: doc. Ing. Bohumil Skala, Ph.D. Schreier Luděk Běloušek Radim Horčic Václav Kurfürst Jiří Experimental Verification of Analytical Results of Five-Phase Induction Motor -Network as the Full-blown Substituting Circuit of the Induction Machine Angular vibration simulation of induction motors with rotor bar fault Simulation Results and Optimization Techniques of The High Speed Machine Session S2 14:00 15:00 Modeling and simulation; Mechatronics; Industrial electronics and power converters Chair: doc. Ing. Pavel Vorel, Ph.D. Záskalický Pavel Richter Aleš Vašíček Adam Lindr David Modeling of Converters with PWM Control of Output Voltage for Small Two-Phase Drives Dynamic Control of Linear Drive on ecam for Biomechanical Simulations Novel resonant mode power supply control approach Two-mass System Vibration Suppression Method Based on the Mechanism Output Speed Processing Session S3 15:20 16:20 Permanent magnet synchronous machines; Design and optimization; Modeling and simulation Chair: prof. Ing. Pavel Záskalický, CSc. Mušák Marek Onufer Matúš Kurfürst Jiří Kurfürst Jiří New Approaches for Parameters Determination of PM Synchronous Motor How to Optimize an Operation of the Synchronous Motor with Permanent Magnets (PMSM) Design of the PM machine and Optimal Shape of Magnets in Terms of Used Magnet Material Preparation of the FEM Model in Order to the Synchronous Generator Optimization Session S4 15:20 16:20 Losses, efficiency, heating, cooling; Electric, thermal, mechanical and electromagnetic field computation, Special electrical machines and equipment; Electrical vehicles, hybrid drives Chair: prof. Ing. Aleš Richter, CSc. Zika Jiří Mukosiej Jerzy Hájek Vítězslav Dúbravka Peter The stray losses in transformer construction parts Thermal Resistances of Equivalent Thermal Networks Combustion Engine Resistance on Starting Display panel for electric vehicle of project EDISON

7 Poster Session 16:20 17:50 Thermal, acoustic noise and vibration; Modeling and simulation; Induction machines; Sensors and actuators; Education in field of electric drives and power electronics; DC machines; Losses, efficiency, heating, cooling; Power systems and renewable energy; Electric drives; Special electrical machines and equipment; Industrial electronics and power converters Chair: Ing. Roman Miksiewicz, Ph.D. Bouzek Lukáš Čáslava Jiří Hejtáková Edita Kaňuch Ján Kosina Petr Kuzdas Jan Mach Martin Zbyněk Makki Zbyněk Makki Michailidis Petr Miksiewicz Roman Mišinger Lukáš Paszek Stefan Rafajdus Pavol Sikora Andrzej Skala Bohumil Španěl Petr Veselka František Nouman Ziad Influence of lamination on natural frequency of the asynchronous machine magnetic core Power sources nonstandard operation possibilities evaluation in MV network Implementation of LTCC to teaching Two-Phase Induction Motor The Pressure sensor Parasitic Effects in Battery Charger Using New SiC Diodes Nonlinear Dynamic Model of PMDC Motor Effect of Blade Rotation on the Pressure on the Outlet Side of the Fan The Difference between the Number of Fan Blades The Connection to the Electrical Grid of the Synchronous Generator Thermal-electromagnetic model of induction motor Slip Ring Induction Motor and Its Faults Under High Inertia Loads Use of power rejection tests for determining synchronous generator nonlinear model parameters Transient Analysis of Power Cable for Ultra-Deep Geothermal Wells Supply control of BLDC motor based on additional windings signals Specialties for a 3phase Transformer Design with the Secondary Winding Comparison of switching losses in hard-switching converter and series resonant converter The Degradation of Fuel Pumps Sliding Contact Embedded Control System Using FPGAs

8 Gala Dinner The Conference Gala Dinner will be held at the Masaryk University Center, Nadrazni 58, Slapanice, Czech Republic. The evening schedule: 18:00 02:00 - dinner (buffet style) o schnitzel o roast meat o platters cheese salad sausage vegetable fruit - wine - beer - coffee - tea - mineral water