DRILLAIR Y35 / X28. for geothermal, waterwell and foundation drilling

Transcription

1 DRILLAIR Y35 / X28 for geothermal, waterwell and foundation drilling

2

3 4 GOOD REASONS to invest in DrillAir Y35 3 I DrillAir Y35 / X % 2.2 Drilling 500 meters per day is achievable with the DrillAir Y35. Two 4.5 x 250 m geothermal wells can be finished in a single drilling day(1). A single truck can carry both the compressor and the rig thanks to the short, 4.1 meter compressor frame. DrillAir Y35 is 100% suitable for sustainable projects, thanks to compliancy with Stage IV emission standards. DrillAir Y35 consumes less than 2.2 liters of fuel per meter drilled (1) for 250 meters holes. (1) Dependent on various operational parameters. Please ask your Atlas Copco representative for more details.

4

5 4 GOOD REASONS to invest in DrillAir X28 5 I DrillAir Y35 / X % 1.7 Drilling 400 meters per day is achievable with the DrillAir X28 with 30 bar maximum pressure. Two 4.5 x 200 m geothermal wells can be finished in a single drilling day (1). A single truck can carry both the compressor and the rig thanks to the short, 4.1 meter compressor frame. DrillAir X28 is 100% suitable for sustainable projects, thanks to compliancy with Stage IV emission standards. DrillAir X28 consumes less than 1.7 liters of fuel per meter drilled (1) for 200 meters holes. (1) Dependent on various operational parameters. Please ask your Atlas Copco representative for more details.

6

7 Higher REVENUES 7 I DrillAir Y35 / X28 High penetration rate with 30 or 35 bar pressure allows to drill more meters in a day. Dynamic Flow Boost gives additional up to 4 m 3 /min when flushing and during drill stem refill. It means faster flushing, faster stem refill and a shorter time to finish a well. Compliancy with Stage IV means a healthier life for our children. It also allows you to work on sustainable projects and for environmentally conscious customers. Atlas Copco XPR * extends the working pressure range. It is based on patented technology and lets you set working pressure as low as 15 bar. * Available only for Drillair Y35

8

9 Lower fuel and transport EXPENSES 9 I DrillAir Y35 / X28 The combination of DrillAirXpert, the Atlas Copco screw element and a Scania engine provides high efficiency for a wide range of pressure and flow. Drilling with bar pressure allows you to drill more meters in an hour. Even though consumption per hour is higher, the cost per meter is lower. A single truck can carry both the compressor and the rig thanks to the DrillAir Y35 s short 4.1 meter frame, which helps to minimize transport expenses.

10

11 Lower maintenance and repair EXPENSES 11 I DrillAir Y35 / X28 Scania Maintenance and repair costs are now predictable. The standard warranty covers parts within two years or 4000 hours (whichever occurs first) (3). A standard warranty can be optionally extended for an additional 2 years or 4000 hours, thus reducing the risk of unexpected expenses up to 4 years or 8000 hours (whichever occurs first)(3) from commissioning date. Scania engines are engineered for maximum uptime. A modular product system and efficient logistics provide outstanding part availability. The Scania network includes over 1000 workshops and more than 370 industrial engine specialists in Europe. Three layer protection coating of all bodywork helps to minimize repainting costs. The top layer, a 100µm powder coat, creates a barrier against mechanical damage. The 100µm layer of primer protects from corrosion infiltrating under the coating. And in the event of coating damage, the steel is protected by a Zincor layer. (3) Please ask your Atlas Copco representative for warranty conditions.

12

13 Higher residual value, lower depreciation EXPENSES 13 I DrillAir Y35 / X28 Scania A single truck can carry both the compressor and the rig thanks to the short 4.1 meter frame. There is no need to invest in a second or a bigger truck. To keep the canopy in good condition for a long period of time, we use three layers of protection: Zincor, primer and powder top coat. The compressor s residual value will be higher if the bodywork is intact. The compressor s residual value is largely defined by the remaining lifetime of the engine at the moment of resale. Scania is well known for its excellent performance and durability. The DrillAir Y35 complies with Stage IV emission standards, so it will have a higher value than similar Stage IIIA or IIIB equipment in the years to come.

14

15 Higher PROFIT REVENUE FUEL EXP. Scania 15 I DrillAir Y35 / X28 Optional LABOR CONSUMABLES TRANSPORTATION MAINTENANCE REPAIR DEPRECIATION PROFIT BEFORE TAX Optional Standard

16 Y35: THE BETTER STAGE IV ENGINE 1,000+ More than 1,000 Scania workshops in Europe 370+ Over 370 engine specialists in Europe 0 costs There are no costs for particulate filter replacement as Scania Stage IV engines don t require one

17 SCANIA Stage IV is the emission standard for non-road engines that was introduced in Europe in January Stage IV-compliant engines REDUCE THE EMISSION OF NO X AND PARTICULATE MATTER TO NEAR-ZERO LEVELS. Compressors with engines that comply with older regulations can still be used, but increasingly companies are required to minimize their environmental impact. This means using compressors that meet the latest emission requirements. 17 I DrillAir Y35 / X28 SCANIA STAGE IV Scania s Stage IV technologies are very reliable and do not affect torque or power output. Scania uses advanced exhaust gas recirculation (EGR) and selective catalytic reduction (SCR) technology that eliminates the need for particulate filters. By injecting a urea-based additive, AdBlue/DEF (diesel exhaust fluid), into the after-treatment system, a chemical reaction takes place that converts the harmful nitrogen oxides (NOx) into diatomic nitrogen (N2) and water. DRILLAIR ENGINES The DrillAir Y35 uses the Scania DC16, an 8-cylinder, 16-liter engine that produces 478 kw of power. X28 is powered by DC13, an 6-cylinder, 13 litter engine with 369 kw power. LOCAL SUPPORT The Scania network includes over 1000 workshops in Europe, all within a two hour drive of your site. Every dealer has a service van to provide on-site service.

18 Features & Options DrillAir Y35 / X28 Features: Easy maintenance with external access to compressor oil Level/refill and new vessel design. Easily accessible centralized draining system and outlet ball valve Easy to operate with the Xc controller Drill more than 700 meters with the 70l AdBlue tank (4) Other features: After-cooler, water separator and bypass valve; 500 hour service interval for the engine; Oiltronix ; pressure toggle switch; 3 stage fuel filter system with water separator; spillage free frame; Certified Integrated Spark Arrester Options: Other options: Options Y35: Automatic fire suppression system, work zone lights, XPR, remote control, cold start and preheater with GSM control Fire extinguisher EU ABS tandem undercarriage Wagon undercarriage Inlet shutdown Options X28: preheater, aftercooler+w aterseparator+bypass, support mounted

19 (4) Dependent on various operational parameters. Please ask your Atlas Copco representative for more details.

20

21 6 DIFFERENCES that matter 21 I DrillAir Y35 / X28 XRVS476 X28 XRYS577 Y35 Length (without undercarriage) 4.1m 4.1m 4.5m 4.1m Flow nominal (Flow in Dynamic flow boost mode) 27.7 (-) m 3 /min 28.3 (32.6) m 3 /min 33.9 (-) m 3 /min 34.5 (39) m 3 /min Maximum pressure Canopy coating 25 bar 2 layers: 2+100μm 30 bar 3 layers: μm 35 bar 2 layers: 2+100μm 35 bar 3 layers: μm Engine Stage IIIA Caterpillar C13 (354 kw) Stage IV Scania DC13 (369 kw) Stage IIIA Caterpillar C18, 6 in-line (18L, 429 kw) Stage IV Scania DC16, V8 (16L, 478 kw) Fuel consumption at 75% load bar bar bar bar

22 22 I DrillAir Y35 / X28

23 TECHNICAL DATA X28 / H32 23 I DrillAir Y35 / X28 TECHNICAL DATA X28 H32 Pressure range bar DrillaiXpert YES YES Extended Pressure range (with optional XPR) bar NA NA Nominal flow at 30 bar m 3 /min (l/s) 28.3 (479) NA Nominal flow at 25 bar m 3 /min (l/s) 28.9 (483) NA Nominal flow at 20 bar m 3 /min (l/s) 31.5 (527) 32.5 (541) Flow in Dynamic Flow Boost mode m 3 /min (l/s) max (544) at 16 bar 35.7 (595) at 14 bar Fuel 30 bar, 100% / 75% flow l/h 78.6/57.7 NA Fuel 25 bar, 100% / 75% flow l/h 73.5/53.1 NA Fuel 20 bar, 100% / 75% flow l/h TBD TBD Engine speed range rpm Engine make Scania DC13 6-in-line Emission compliance Stage IV Engine power (DIN 627 1) KW 369 AdBlue tank capacity l 70 DIMENSION AND FUEL CAPACITY Wagon High speed tandem Dimensions m 4.91x2.14x x2.14x2.48 Fuel tank capacity l Weight (excl. fuel, AdBlue) kg 5880 TBD Weight (incl. fuel, AdBlue) kg 6500 TBD

24 24 I DrillAir Y35 / X28

25 TECHNICAL DATA Y35 / V39 25 I DrillAir Y35 / X28 TECHNICAL DATA Y35 V39 Pressure range bar DrillaiXpert YES YES Extended Pressure range (with optional XPR) bar NA Nominal flow at 30 bar m 3 /min (l/s) 34.8 (580) NA Nominal flow at 25 bar m 3 /min (l/s) 35.8 (596) 39.0 (650) Flow in Dynamic Flow Boost mode m 3 /min (l/s) max (650) at 22 bar 43.3 (722) at 17 bar Fuel 35 bar, 100% / 75% flow l/h 100.4/72.3 TBD Fuel 25 bar, 100% / 75% flow l/h 87.6/64.0 TBD Engine speed range rpm Engine make Scania DC16 V8 Emission compliance Stage IV Engine power (DIN 627 1) KW 478 AdBlue tank capacity l 70 DIMENSION AND FUEL CAPACITY Wagon Support mounted High speed tandem Dimensions m 6.2x2.2x x2.2x x2.4x3.1 Fuel tank capacity l Weight (excl. fuel, AdBlue) kg Weight (incl. fuel, AdBlue) kg

26

27

28 COMMITTED TO SUSTAINABLE PRODUCTIVITY We stand by our responsibilities towards our customers, towards the environment and the people around us. We make performance stand the test of time. This is what we call - Sustainable Productivity Printed in Belgium Subject to alteration without prior notice. Copyright 2015, Atlas Copco Airpower n.v., Wilrijk, Belgium.