Vacuum Pump Systems RUTA m 3 x h -1 (147 to 765 cfm)
|
|
- Reynold Dalton
- 5 years ago
- Views:
Transcription
1 Vacuum Pump Systems RUTA m 3 x h -1 (17 to 765 cfm) Excerpt from the Product Section C08 Edition May 007
2 Contents General Overview C08.03 Types of Pumps Systems C08.0 Products Pump Systems (Global Versions) Three-Stage RUTA Pump Systems with Two-Stage TRIVAC Backing Pumps Adaptor Version C08.06 Frame Version C08.08 Two-Stage RUTA Pump Systems with Single-Stage SOGEVAC Backing Pumps Adaptor Version C08.10 Frame Version C08.1 Two- and Three-Stage RUTA Pump Systems with Single- and Two-Stage Rotary Piston Vacuum Pumps as Backing Pumps C08.1 Dry Compressing Vacuum Pump System RUTA with SCREWLINE SP630 Backing Pump Adaptor Version C08.16 Frame Version C08.18 RUVAC RAV Roots Vacuum Pumps with Pre-Admission Cooling C08.0 Pump Systems RUTA RAV with RUVAC RAV Roots Vacuum Pumps Two- Stage C08. Three-Stage C08. TVD Pump Systems for Drying, Evaporation and Distillation Applications C08.6 Pump Systems (Only available for purchase in North and South America) RBS - B/BCS Roots Pump Systems with Two-Stage TRIVAC Backing Pumps C08.8 HTS Close-Coupled Pump Systems with Single-Stage SOGEVAC Backing Pumps C08.3 SP Close-Coupled Pump Systems with SCREWLINE Dry Compressing Backing Pumps C08.36 Accessories Sound Proofing C08.0 Isolation against Vibrations C08.0 Dust Separators C08.0 Frequency Inverter RUVATRONIC RT C08.0 Electric Controller C08.1 Pressure Control C08.1 Dust Filter F-xxx-C C08. Miscellaneous Checklist for Inquiries (Fax Form) C08. C08 0
3 General Overwiew A continually increasing number of applications in industry and research are relying on vacuum technology. Thus widely differing requirements result regarding the vacuum generating systems. The comprehensive range of vacuum pumps from Leybold Vacuum offers, in combination with the matching accessories, all options of se-lecting the optimum pump system for your application in each case. Based on the longstanding experience in the design and manufacture of vacuum pump systems, Leybold Vacuum offers standardized pump systems which will match most applications the RUTA pump systems. Designation of Roots Vacuum Pump Systems Leybold Vacuum pump combinations of Roots vacuum pumps with backing pumps are called RUTA. In order to identify the standard pump systems the name RUTA is followed by the brief designations of the pumps which make up a particular pump system. Brief designation of the largest Roots vacuum pump (Pumping speed of the pump system) Brief designation of the smaller Roots vacuum pump Cooler or condenser (if present) Brief designation of the backing pump Type of pump system (adaptor (A) or frame (G)) The pump system designation is arranged as follows: RUTA WAU 001 / WAU 501 / K / D 65 B / A RUTA pump systems excel by being compact, reliable and servicefriendly. The pump systems are equipped as standard with 00 V, 50 Hz threephase motors. Motors for special supply voltages, special mains frequencies or explosion protected pumps are available. Standards Leybold Vacuum pump systems are rated according to CE, ISO, DIN and VDE regulations. Compliance with other standards is possible upon request. The technical data of the vacuum pump systems given in this product section are based on the PNEUROP Acceptance Specifications for Vacuum Pumps, Part 1, and comply with DIN 8 6. The characteristic curves in our pumping speed diagrams are plotted in accordance with DIN 8 6. The curves represent the mean of several measurements. Our warranty refers to the values indicated in the technical data table. 03 C08
4 Types of Pump Systems Typical areas of application for RUTA pump systems are industry, research and chemistry. Here the focus is on processes for metal production and processing, drying and degassing, thermal treatment, coating in the area of semiconductor manufacture as well as surface refinement. RUTA pump systems are also used as backing pump sets for high vacuum systems in combination with diffusion pumps, turbomolecular pumps and cryo pumps. RUTA RA 3001/WAU1001/SV300 The RUTA pump systems described here have been designed for rough and medium vacuum operation, i.e. for the pressure range from atmospheric pressure down to 10 - mbar (7.5 x 10-5 Torr). RUTA pump systems consist of a combination of individual pumps whereby Roots vacuum pumps are employed on the intake side. Further compression to atmospheric pressure may be performed either by oil-sealed or drycompressing vacuum pumps, liquid ring pumps or Roots vacuum pumps with pre-inlet cooling. All combinations may be equipped at suitable places with condensers. The selection criteria for a RUTA pump system are as follows: - Pumping speed - Operating pressure - Process conditions - Characteristics of the media - Standards and regulations which depend on the area of application and the produced products. Standard RUTA Pump Systems Our Roots vacuum pumps WA, WS and RA or WAU and WSU with integrated bypass line or RA with external bypass line (RAU) are combined with oil-sealed backing pumps for conventional generation of the vacuum. Single stage arrangements are capable of delivering pumping speeds of 50 to m 3 /h (17.3 to 9 cfm). Higher pumping speeds can be attained by paralleling several pumps. The attainable operating pressures depend on the number of pumping stages. For higher pumping speeds or lower ultimate pressures, three or multistage pump systems equipped with single or two-stage backing pumps are available (see figure). RUTA Pump Systems with Condensers If vacuum systems must pump larger quantities of vapor or vapor gas mixtures, it is economical to insert condensers which are cooled with water or a different coolant at a suitable place within the pump system. Cooled condensers are themselves effective partial pumps which condense most of the vapors from the pumped media. The downstream mechanical pumps will then only need to pump those gases which have not already condensed. The quantity of vapor present in each case determines the size of the condenser and the temperature at which it is operated. The size of the downstream pump is determined by the quantity of non-condensable gases, the required pressure and the required pump-down time for the system. All pump systems of the WA/WAU, WS/WSU and RA series may be equipped with one or several condensers. These are often used in the chemical industry. Here RUTA vacuum pump systems with condensers are not only used to generate a vacuum, but they are also often employed in the recovery of solvents. When installing one or several Roots pumps upstream of a condenser, low operating pressures and high condensation pressures can be attained. Thus the condenser may in many cases be operated with cooling water instead of brine. The vapor components pumped together with inert gases may be separated once more in an emission condenser on the exhaust side so that the quality of the exhaust gas can be maintained within close tolerance regarding its cleanness. Dry-Compressing RUTA Vacuum Pump Systems Increasing environmental awareness, pumping of condensable vapors or high requirements regarding cleanness when pumping highquality media which must not be contaminated by other media for recycling, often requires the use of universal pumps where the pump chamber is free of operating agents (dry pumps). Here Leybold Vacuum offers two solutions: 1. Pump systems consisting of the SCREWLINE screw vacuum pump developed specifically for the process industry in combination with one or several Roots vacuum pumps.. Single or multistage RUTA RAV vacuum pump systems, consisting of Roots vacuum pumps with pre-admission cooling. C08 0
5 The operating pressure ranges of the pump systems depend on the number of Roots vacuum pumps, but will extend in any case without interruptions to atmospheric pressure. Already in connection with one Roots pump, pump systems with a SCREWLINE pump are capable of attaining base pressures of < 1 x 10-3 mbar (7.5 x 10 - Torr). Single-stage RAV combinations attain an ultimate pressure of 150 mbar (11.5 Torr) and twostage combinations 50 mbar (37.5 Torr). Multi-stage combinations with Roots vacuum pumps of all systems are capable of attaining pressures below 10 - mbar (7.5 x 10-5 Torr). RUTA Custom Pump Systems Most users will be able to select the right pump system for their application from our range of standard pump systems. In special cases a custom design may be required for special processes and high pumping speeds. We are prepared to design and manufacture custom pump systems according to customers specifications. If required we will use - besides oil-sealed and dry-compressing backing pumps - liquid ring and ejector pumps. RUTA Pump Systems for the Metal Producing and Processing Industry In common vacuum furnace processes such as hardening, annealing, brazing, melting and casting, preferably oil-sealed or dry compressing standard vacuum pump systems are usually used. The oil-sealed systems consist of a combination of Roots vacuum pumps with a single or twostage rotary vane or rotary piston pump. In the dry compressing systems our screw vacuum pump SCREWLINE is used as the backing pump. The vacuum pumps are mounted in a rugged frame. The design of the pump systems is service-friendly, modular and can be easily upgraded with additional equipment. On smaller furnaces RUVAC WAU Roots vacuum pumps are the most suitable because these may be cut-in at a higher operating pressure, while on larger furnaces and particularly where short pump-down cycles are required, the use of RUVAC RA Roots vacuum pumps with suitably sized backing pumps is advisable. For special processes, e.g. fusion or degassing of molten masses, due to the high dust contents, the additional use of a dust separator is required as well as equipping the backing pumps with oil filtering units. RUTA Pump Systems for the Chemical Industry In chemical processes it is often necessary to remove corrosive, condensable and reactive gases and vapors. Leybold Vacuum designs and manufactures custombuilt pump systems for specific process applications. Depending on the type of application, either a rotary vane pump, or a dry compressing screw vacuum pump (SCREWLINE, for example), a liquid ring pump or a combination of gas jet pump and liquid ring pump may be used as the backing pump. To ensure dependable monitoring of the system, the following monitoring devices, among others, may be installed: - Temperature sensors to monitor the gas temperatures between the pump stages and the pump body temperature, - Water flow monitors for the cooling water supply to pumps and condensers, - Differential pressure indicator with control setpoint to monitor the exhaust filters of the rotary vane vacuum pump. Pump Systems for Drying, Evaporation and Distillation Applications (TVD) More and more vacuum applications are finding their way into the areas of environmental protection, recycling and waste disposal. Waste disposal of used oil and aromatic compounds and Cleaning processes in metalprocessing factories demonstrate that the combination of vacuum know-how, innovative engineering and applications know-how is indispensable for the successful application of vacuum technology in most widely differing applications. The product is no longer in the foreground, solutions to problems are demanded instead. TVD pump system, mobile with control cabinet Leybold Vacuum has developed some continuously operating vacuum pump systems for these applications. These systems basically consist of a rotary vane pump with a condenser unit. Upon request the condenser arrangement may also be equipped with a cold water set. This version will then be independent of any cooling water connections and being a mobile system it is well-suited for operation at varying locations. 05 C08
6 Products Three-Stage RUTA Pump Systems with Two-Stage TRIVAC Backing Pumps, Adaptor Version RUTA WAU 501/D65B/A Standard Equipment - Exhaust filter - Oil collecting pan - Manually operated gas ballast - Crane eyes on the frame - Floor mounting - The oil is supplied with the pump - CE approval Options - Frequency inverter RUVATRONIC RT for controlling the speed of the Roots pump - Oil filter - V DC gas ballast valve - Sound proofing box - Vibration absorbers - Castors - Different types of floor mounts - Oil drain valve on each pump - Exhaust filter with oil return line - Special motors - Electric control systems l 1 b 1 l DN 1 b DN h h 1 l c b RUTA 51/D0B/A 51/D65B/A 501/D65B/A RUVAC WA/WAU/WS/WSU P Backing pump TRIVAC P1 D 0 B D 65 B D 65 B DN 1 63 ISO-K 63 ISO-K 63 ISO-K DN 0 ISO-KF 0 ISO-ISO-KF 0 ISO-KF l 1000 (39.37) 1000 (39.37) 1000 (39.37) l (1.76) 375 (1.76) 375 (1.76) l 3(9.1) 3 (9.1) 3 (9.1) b 600 (3.6) 600 (3.6) 600 (3.6) b (13.78) 350 (13.78) 350 (13.78) b 0 (1.57) 0 (1.57) 0 (1.57) h 85 (33.6) 85 (33.6) 89 (35.0) h 1 88 (19.1) 88 (19.1) 88 (19.1) c 100 (3.9) 100 (3.9) 100 (3.9) Dimensional drawing for the pump systems with TRIVAC D0/65 B backing pumps on pallet; dimensions in brackets ( ) are in inch C08 06
7 Technical Data, 50 Hz RUVAC (WA/WAU/WS/WSU possible) Backing pump TRIVAC P P1 RUTA WAU 51/D0B/A 51/D65B/A 501/D65B/A D 0 B D 65 B D 65 B Pumping speed, 50 Hz at 10-1 mbar (7.5 x 10 - Torr) m 3 x h -1 (cfm) 00.0 (117.8) 10.0 (13.7) (3.8) Ultimate partial pressure Ultimate total pressure with gas ballast Installed motor power Power consumption at 10-1 mbar (7.5 x 10 - Torr) Noise level to DIN max. without gas ballast at 1 mbar (0.75 Torr) Oil filling, total, approx. Weight, total, approx. mbar (Torr) mbar (Torr) db(a) db(a) l (qt) kg (lbs) < x 10-5 (< 1.5 x 10-5 ) < x 10-5 (< 1.5 x 10-5 ) < x 10-5 (< 1.5 x 10-5 ) < 8 x 10 - (< 6 x 10 - ) < 8 x 10 - (< 6 x 10 - ) < 8 x 10 - (< 6 x 10 - ).6 (3.5) 3.3 (.5). (6.0).0 (.7).5 (3.).7 (3.7) (3.9).0 (.3).3 (.55) 5.0 (50.) 60.0 (573.3) (67.5) Connecting flange Inlet port DN 1 Outlet port DN 63 ISO-K 63 ISO-K 63 ISO-K 0 ISO-KF 0 ISO-KF 0 ISO-KF Ordering Information RUVAC (WA/WAU/WS/WSU possible) Backing pump TRIVAC P P1 RUTA WAU 51/D0B/A 51/D65B/A 501/D65B/A WAU 51 WAU 51 WAU 501 D 0 B D 65 B D 65 B Pump system, complete (adaptor version), pallet mounted, with Roots vacuum pump RUVAC WAU Frequency inverter RUVATRONIC (see description in Section Accessories ) Part No Part No Part No RT 5/51 RT 5/51 RT 5/501 Part No Part No Part No mbar 10 Pressure WAU 51 +D0B WAU 51 +D65B WAU 501 +D65B min Pump-down time Torr m 3 x h -1 Pumping speed Torr WAU 51 +D 0 B WAU 51 +D 65 B WAU 501 +D 65 B WAU 1001+D 65 B mbar Total pressure Pressure Partial pressure cfm Pump-down time diagram for a 10 m 3 tank at 50 Hz Pumping speed diagram at 50 Hz 07 C08
8 Three-Stage RUTA Pump Systems with Two-Stage TRIVAC Backing Pumps, Frame Version RUTA WAU 501/D65B/G Standard Equipment - Exhaust filter - Oil collecting pan - Manually operated gas ballast - Crane eyes on the frame - Floor mounting - The oil is supplied with the pump - CE approval Options - Frequency inverter RUVATRONIC RT for controlling the speed of the Roots pump - Oil filter - V DC gas ballast valve - Sound proofing box - Vibration absorbers - Castors - Different types of floor mounts - Oil drain valve on each pump - Exhaust filter with oil return line - Special motors - Electric control systems l 1 b 1 l DN 1 b h DN h h 1 l c b RUTA 51/D0B/G 51/D65B/G 501/D65B/G 1001/D65B/G RUVAC WA/WAU/WS/WSU P Backing pump TRIVAC P1 D 0 B D 65 B D 65 B D 65 B DN 1 63 ISO-K 63 ISO-K 63 ISO-K 100 ISO-K DN 0 ISO-KF 0 ISO-KF 0 ISO-KF 0 ISO-KF l 1000 (39.37) 1100 (3.31) 1150 (5.8) 1300 (51.18) l 1 00 (15.75) 80 (18.90) 80 (18.90) 80 (18.90) l 3 (9.1) 31 (1.36) 31 (1.36) 31 (1.36) b 560 (.05) 560 (.05) 560 (.05) 600 (3.6) b 1 80 (11.0) 80 (11.0) 80 (11.0) 80 (11.0) b 59 (.3) 59 (.3) 59 (.3) 59 (.3) h 977 (38.6) 977 (38.6) 1017 (0.0) 1067 (.01) h 1 88 (19.1) 88 (19.1) 88 (19.1) 88 (19.1) h 677 (6.65) 677 (6.65) 677 (6.65) 671 (6.) c 100 (3.9) 100 (3.9) 100 (3.9) 100 (3.9) Dimensional drawing for the pump systems with TRIVAC D0/65 B backing pumps in a frame; dimensions in brackets ( ) are in inch C08 08
9 Technical Data, 50 Hz RUVAC (WA/WAU/WS/WSU possible) Ordering Information P Backing pump TRIVAC P1 Pumping speed, 50 Hz at 10-1 mbar (7.5 x 10 - Torr) m 3 x h -1 (cfm) Ultimate partial pressure mbar (Torr) Ultimate total pressure with gas ballast Installed motor power Power consumption at 10-1 mbar (7.5 x 10 - Torr) Noise level to DIN max. without gas ballast at 1 mbar (0.75 Torr) Oil filling, total, approx. mbar (Torr) db(a) db(a) l (qt) Weight, total, approx. kg (lbs) Connecting flange Inlet port DN 1 Outlet port DN RUVAC (WA/WAU/WS/WSU possible) P Backing pump TRIVAC P1 Pump system, complete (frame version), frame mounted, with Roots vacuum pump RUVAC WAU Frequency inverter RUVATRONIC (see description in Section Accessories ) RUTA WAU 51/D0B/G 51/D65B/G 501/D65B/G 1001/D65B/G D 0 B D 65 B D 65 B D 65 B (109.0) 05.0 (10.7) 30.0 (00.3) 60.0 (365.) < x 10-5 < x 10-5 < x 10-5 < x 10-5 ) (< 1.5 x 10-5 ) (< 1.5 x 10-5 ) (< 1.5 x 10-5 ) (< 1.5 x 10-5 ) < 8 x 10 - < 8 x 10 - < 8 x 10 - < 8 x 10 - (< 6 x 10 - ) (< 6 x 10 - ) (< 6 x 10 - ) (< 6 x 10 - ).6 (3.5) 3.3 (.5). (6.0) 6. (8.).0 (.7).5 (3.).7 (3.7) 3.0 (.1) (.5).0 (.3).3 (.55) 5.3 (5.60) 80.0 (617.) (683.6) (771.8) 60.0 (101.3) 63 ISO-K 63 ISO-K 63 ISO-K 100 ISO-K 0 ISO-KF 0 ISO-KF 0 ISO-KF 0 ISO-KF RUTA WAU 51/D0B/G 51/D65B/G 501/D65B/G 1001/D65B/G WAU 51 WAU 51 WAU 501 WAU 1001 D 0 B D 65 B D 65 B D 65 B Part No Part No Part No Part No RT 5/51 RT 5/51 RT 5/501 RT 5/1001 Part No Part No Part No Part No mbar 10 Pressure WAU 51 +D0B WAU 51 +D65B WAU 501 +D65B WAU 1001+D65B min Pump-down time Torr m 3 x h -1 Pumping speed Torr WAU 51 +D 0 B WAU 51 +D 65 B WAU 501 +D 65 B WAU 1001+D 65 B mbar Pressure Total pressure Partial pressure cfm Pump-down time diagram for a 10 m 3 tank at 50 Hz Pumping speed diagram at 50 Hz 09 C08
10 Two-Stage RUTA Pump Systems with Single-Stage SOGEVAC Backing Pumps, Adaptor Version RUTA WAU 1001/SV00/A Standard Equipment - Exhaust filter with oil return line - Oil filter - Oil collecting pan - Manually operated gas ballast - Floor mounting - The oil is supplied with the pump - CE approval Options - Frequency inverter RUVATRONIC RT for controlling the speed of the Roots pump - V DC gas ballast valve - Sound proofing box - Vibration absorbers - Castors - Different types of floor mounts - Oil drain valve on each pump - Special motors - Electric control systems l 1 l b b 1 l 1 b 1 DN 1 l DN 1 DN DN h b h l c h 1 c h 1 b l b RUTA 501/SV 00/A 1001/SV 00/A 1001/SV 300/A 001/SV 630F/A RUVAC WA/WAU/WS/WSU P Backing pump SOGEVAC P1 SV 00 SV 00 SV 300 SV 630 DN 1 63 ISO-K 100 ISO-K 100 ISO-K 160 ISO-K DN " " " 100 ISO-K l 96 (37.87) 1050 (1.3) 108 (.60) 1800 (70.87) l 1 (9.53) 303 (11.93) 303 (11.93) 80 (3.8) l 70 (.76) 77 (3.03) 77 (3.03) 35 (1.38) b 700 (7.56) 700 (7.56) 700 (7.56) 1000 (39.37) b 1 30 (9.06) 30 (9.06) 30 (9.06) 50 (17.7) b 99 (19.65) 99 (19.65) 99 (19.65) 76 (30.08) h 873 (3.37) 93 (36.3) 93 (36.3) 10 (55.0) h 1 68 (18.3) 68 (18.3) 68 (18.3) 805 (31.69) c 100 (3.9) 100 (3.9) 100 (3.9) 100 (3.9) Dimensional drawing for the pump systems with SOGEVAC SV 00 and 300 backing pumps [left], SOGEVAC SV 630 F [right]; dimensions in brackets ( ) are in inch C08 10
11 Technical Data, 50 Hz RUVAC (WA/WAU/WS/WSU possible) Ordering Information P Backing pump SOGEVAC P1 Pumping speed, 50 Hz at 10-1 mbar (7.5 x 10 - Torr) m 3 x h -1 (cfm) Ultimate partial pressure mbar (Torr) Ultimate total pressure with gas ballast Installed motor power Power consumption at 10-1 mbar (7.5 x 10 - Torr) Noise level to DIN without gas ballast at 10-1 mbar (7.5 x 10 - Torr) Oil filling, total, approx. mbar (Torr) db(a) l (qt) Weight, total, approx. kg (lbs) Connecting flange Inlet port DN 1 Outlet port DN RUVAC (WA/WAU/WS/WSU possible) P Backing pump SOGEVAC P1 Pump system, complete (adaptor version), pallet mounted, with Roots vacuum pump RUVAC WAU Frequency inverter RUVATRONIC (see description in Section Accessories ) RUTA WAU 501/SV00/A 1001/SV00/A 1001/SV300/A 001/SV630F/A SV 00 SV 00 SV 300 SV 630 F (15.0) (1.0) (30.0) (995.) < 8 x 10-3 < 8 x 10-3 < 8 x 10-3 < 8 x 10-3 (< 6 x 10-3 ) (< 6 x 10-3 ) (< 6 x 10-3 ) (< 6 x 10-3 ) < x 10 - < x 10 - < x 10 - < x 10 - (< 3 x 10 - ) (< 3 x 10 - ) (< 3 x 10 - ) (< 3 x 10 - ) 6. (8.) 8.0 (10.9) 9.5 (1.9).5 (30.6) 3.0 (.1) 3.5 (.8).0 (5.) 16.5 (.) (6.3) 7.0 (7.) 11.0 (11.63) 39.0 (1.3) (738.7) 30.0 (98.) 80.0 (1058.) (513.7) 63 ISO-K 100 ISO-K 100 ISO-K 160 ISO-K " " " 100 ISO-K RUTA WAU 501/SV00/A 1001/SV00/A 1001/SV300/A 001/SV630F/A WAU 501 WAU 1001 WAU 1001 WAU 001 SV 00 SV 00 SV 300 SV 630 F Part No Part No Part No Part No RT 5/501 RT 5/1001 RT 5/1001 RT 5/001 Part No Part No Part No Part No Pressure mbar Pump-down time WAU SV00 WAU SV00 WAU SV300 WAU SV630F min Torr m 3 x h -1 Pumping speed Torr WAU 001+SV 630F WAU 1001+SV 300 WAU 1001+SV 00 WAU 501 +SV mbar Pressure Total pressure Partial pressure 5000 cfm Pump-down time diagram for a 10 m 3 tank at 50 Hz Pumping speed diagram at 50 Hz 11 C08
12 Two-Stage RUTA Pump Systems with Single-Stage SOGEVAC Backing Pumps, Frame Version RUTA WAU 001/SV300/G Standard Equipment - Exhaust filter with oil return line - Oil filter - Oil collecting pan - Manually operated gas ballast - Crane eyes on the frame - Floor mounting - The oil is supplied with the pump - CE approval Options - Frequency inverter RUVATRONIC RT for controlling the speed of the Roots pump - V DC gas ballast valve - Sound proofing box - Vibration absorbers - Castors - Different types of floor mounts - Oil drain valve on each pump - Special motors - Electric control systems l 1 b 1 l 1 b1 DN1 DN 1 b l DN h h h h DN b l h 1 h1 l c b RUTA 1001/SV300/G 001/SV300/G 3001/SV630F/G 5001/SV630F/G 7001/SV100/G RUVAC RA P RUVAC WA/WAU/WS/WSU P Backing pump SOGEVAC P1 SV 300 SV 300 SV 630 SV 630 SV 100 DN ISO-K 160 ISO-K 50 ISO-K 50 ISO-K 50 ISO-K DN " " 100 ISO-K 100 ISO-K 160 ISO-K l 130 (5.76) 130 (5.76) 150 (8.65) 150 (8.65) 35 (91.5) l (1.96) 380 (1.96) 950 (37.0) 950 (37.0) 975 (38.39) l 110 (.33) 110 (.33) 165 (6.5) 165 (6.5) 05 (15.9) b 710 (7.95) 780 (30.71) 1100 (3.31) 1100 (3.31) 1360 (53.5) b 1 50 (9.8) 30 (1.60) 500 (19.69) 500 (19.69) 580 (.83) b 191 (7.5) 191 (7.5) 85 (11.) 85 (11.) 158 (6.) h 1176 (6.30) 159 (9.57) 179 (70.55) 1896 (7.65) 580 (101.58) h (0.39) 518 (0.39) 75 (9.33) 75 (9.33) 100 (0.16) h 780 (30.71) 79 (8.70) 1177 (6.3) 1151 (5.31) 1835 (7.) c 100 (3.9) 100 (3.9) 100 (3.9) 100 (3.9) 100 (3.9) Dimensional drawing for the pump systems with SOGEVAC SV 300 and 630 F backing pumps [left], SOGEVAC SV 100 [right]; dimensions in brackets ( ) are in inch c l b C08 1
13 Technical Data, 50 Hz RUVAC RA RUVAC (WA/WAU/WS/WSU possible) Ordering Information P P Backing pump SOGEVAC P1 Pumping speed, 50 Hz at 10-1 mbar (7.5 x 10 - Torr) m 3 x h -1 (cfm) Ultimate partial pressure mbar (Torr) Ultimate total pressure with gas ballast Installed motor power Power consumption at 10-1 mbar (7.5 x 10 - Torr) Noise level to DIN without gas ballast at 10-1 mbar (7.5 x 10 - Torr) Oil filling, total, approx. mbar (Torr) db(a) l (qt) Weight, total, approx. kg (lbs) Connecting flange Inlet port DN 1 Outlet port DN RUTA 1001/SV300/G 001/SV300/G 3001/SV630F/G 5001/SV630F/G 7001/SV100/G SV 300 SV 300 SV 630 F SV 630 F SV (30) 15 (850) 3090 (1818) 10 (78) 550 (350) < 8 x 10-3 < 8 x 10-3 < 8 x 10-3 < 8 x 10-3 < 8 x 10-3 (< 6 x 10-3 ) (< 6 x 10-3 ) (< 6 x 10-3 ) (< 6 x 10-3 ) (< 68 x 10-3 ) < x 10 - < x 10 - < x 10 - < x 10 - < x 10 - (< 3 x 10 - ) (< 3 x 10 - ) (< 3 x 10 - ) (< 3 x 10 - ) (< 3 x 10 - ) 9.5 (1.9) 13.0 (17.7) 6.0 (35.) 30.0 (0.8) 33.5 (5.6).0 (5.).5 (6.1) 17.0 (3.1) 17.5 (3.8) 18.0 (.5) (11.63) (13.8) 70.0 (1631.7) (3858.8) (189.5) (6615) 100 ISO-K 160 ISO-K 50 ISO-K 50 ISO-K 50 ISO-K " " 100 ISO-K 100 ISO-K 160 ISO-K RUTA 1001/SV300/G 001/SV300/G 3001/SV630F/G 5001/SV630F/G 7001/SV100/G RUVAC RUVAC (WA/WAU/WS/WSU possible) Backing pump SOGEVAC Pump system, complete (frame version), frame mounted, with Roots vacuum pump RUVAC RA RUVAC WAU Frequency inverter RUVATRONIC (see description in Section Accessories ) P P P1 RA 3001 RA 5001 RA 7001 WAU 1001 WAU 001 SV 300 SV 300 SV 630 F SV 630 F SV 100 Part No Part No Part No Part No Part No RT 5/1001 RT 5/001 RT 5/3001 RT 5/5001 RT 5/7001 Part No. Part No. Part No. Part No. Part No ) ) ) 1) With this combination, continouos operation of the Roots pump is not possible at atmospheric pressure Torr Pressure mbar WAU SV300 WAU001 + SV300 RA SV630F RA SV630F RA SV min Pump-down time Torr Pumping speed 10 m 3 x h WAU 1001+SV 300 WAU 001+SV 300 RA SV 630F RA SV 630F RA SV mbar 3 Total pressure Pressure Partial pressure 5000 cfm Pump-down time diagram for a 10 m 3 tank at 50 Hz Pumping speed diagram at 50 Hz 13 C08
14 Two and Three-Stage RUTA Pump Systems with Single- and Two-Stage Rotary Piston Vacuum Pumps as Backing Pump RUTA WAU 001/E50/G Standard Equipment - Exhaust filter attached - Oil collecting pan - SECUVAC valve V DC - Backing pump removable by a fork lifter - Crane eyes on the frame - Floor mounting - The oil is supplied with the pump - CE approval Options - Frequency inverter RUVATRONIC RT for controlling the speed of the Roots pump - Oil filter - V DC gas ballast valve - Sound proofing box - Vibration absorbers - Different types of floor mounts - Oil drain valve on each pump - Exhaust filter box with oil return - Special motors - Electric control systems b1 DN 1 b DN h h1 h l 1 l l RUTA 1001/E50/G 001/E50/G 1001/DK00/G RUVAC WA/WAU/WS/WSU P Rotary piston vacuum pump P1 E 50 1) E 50 1) DK 00 1) DN ISO-K 160 ISO-K 100 ISO-K DN 63 ISO-K 63 ISO-K 63 ISO-K l 1650 (6.96) 1650 (6.96) 1650 (6.96) l (6.77) 680 (6.77) 680 (6.77) l 1398 (55.0) 1395 (5.9) 1398 (55.0) b 850 (33.6) 910 (35.83) 850 (33.6) b 1 60 (10.) 335 (13.19) 60 (10.) b 38 (9.37) 3 (8.78) 38 (9.37) h 153 (59.96) 1705 (67.13) 153 (59.96) h 1 87 (3.33) 89 (35.0) 87 (3.33) h 117 (.37) 1175 (6.6) 117 (.37) 1) Alternatively with AFK exhaust filter box instead of the exhaust filter; then dimensions l 1 and b will change b Dimensional drawing for the pump systems with E and DK backing pumps; dimensions in brackets ( ) are in inch C08 1
15 Technical Data, 50 Hz RUVAC (WA/WAU/WS/WSU possible) P Rotary piston vacuum pump P1 Pumping speed, 50 Hz at 1 mbar (0.75 Torr) m 3 x h -1 (cfm) at 10-1 mbar (7.5 x 10 - Torr) m 3 x h -1 (cfm) Ultimate partial pressure mbar (Torr) Ultimate total pressure with gas ballast mbar (Torr) Installed motor power Installed motor power at 1 mbar (0.75 Torr) at 10-1 mbar (7.5 x 10 - Torr) Noise level to DIN max. db(a) without gas ballast at 1 mbar (0.75 Torr) db(a) without gas ballast at 10-1 mbar (7.5 x 10 - Torr) db(a) Oil filling, total, approx. l (qt) Weight, total, approx. kg (lbs) Connecting flange Inlet port DN 1 Outlet port DN RUTA WAU 1001/E50/G 001/E50/G RUTA WSU 1001/DK00/G E 50 E 50 DK (71.) (795.) (80.0) x 10-3 (1.5 x 10-3 ) x 10-3 (1.5 x 10-3 ) 3 x 10-5 (.3 x 10-5 ) x 10 - (1.5 x 10 - ) x 10 - (1.5 x 10 - ) 3 x 10 - (.3 x 10 - ) 9.5 (1.9) 13.0 (17.7) 9.5 (1.9).0 (5.).7 (6.). (6.0) (11.63) 1.0 (1.68) 6.0 (6.3) (1973.5) (381.) (050.7) 100 ISO-K 160 ISO-K 100 ISO-K 63 ISO-K 63 ISO-K 63 ISO-K Ordering Information RUVAC (WA/WAU/WS/WSU possible) Rotary piston vacuum pump Pump system, complete (frame version), frame mounted, with Roots vacuum pump RUVAC WAU RUVAC WSU Frequency inverter RUVATRONIC (see description in Section Accessories ) P P1 RUTA WAU 1001/E50/G 001/E50/G RUTA WSU 1001/DK00/G WAU 1001 WAU 001 WSU 1001 E 50 E 50 DK 00 Part No Part No Part No RT 5/1001 RT 5/001 RT 5/1001 Part No Part No Part No Pressure mbar WAU 1001+E 50 WAU 001+E WAU 1001+DK min 0 Pump-down time 750 Torr Pump-down time diagram for a 10 m 3 tank at 50 Hz Pumping speed 10 m 3 x h Pumping speed diagram at 50 Hz Torr WAU 001+E 50 WAU 1001+E 50 WSU 1001+DK mbar Pressure Total pressure Partial pressure cfm C08
16 Dry-Compressing Vacuum Pump System RUTA with SCREWLINE SP630 Backing Pump, Adaptor Version RUTA WSU 001/SP630/A Standard Equipment - Silencer - SP Guard - Manually operated gas ballast - Gear oil collecting pan integrated within the SCREWLINE - Gear oil supplied with the pump - CE approval Options - Frequency inverter RUVATRONIC RT for controlling the speed of the Roots pump - Condensate drain valve at the silencer - Sound proofing box - Vibration absorbers - SCREWLINE with water cooling - Castors - Different types of floor mounts - Oil drain valve on each pump - Electric control systems b l1 b1 b DN1 DN h h1 l l b3 b* 1) RUTA 001/SP630/A RUVAC WA/WAU/WS/WSU P 001 Backing pump SCREWLINE P1 SP630 DN ISO-K DN 100 ISO-K l 1850 (7.8) l (1.96) l 89 (35.1) b 106 (1.89) b 1 00 (15.75) b 55 (1.81) b (31.50) b 70 (.76) h 1518 (59.76) h (5.33) 1) Clearance for maintenance Dimensional drawing of the pump systems with dry compressing SCREWLINE SP630 backing pump, adapter version; dimensions in brackets ( ) are in inch C08 16
17 Technical Data, 50 Hz RUVAC (WA/WAU/WS/WSU possible) Backing pump SCREWLINE P P1 RUTA WAU 001/SP630/A 001 SP630 Pumping speed, 50 Hz at 10-1 mbar (7.5 x 10 - Torr) m 3 x h -1 (cfm) 1780 (1050) Ultimate total pressure without gas ballast Installed motor power Electrical power consumption at 10-1 mbar (7.5 x 10 - Torr) mbar (Torr) < 1 x 10-3 (< 7.5 x 10 - ).5 (30.0) 11.7 (15.7) Noise level to DIN with silencer at 10-1 mbar (7.5 x 10 - Torr) db(a) 79 Weight, total, approx. kg (lbs) 1100 (30) Connecting flange Inlet port DN 1 Outlet port DN 160 ISO-K 100 ISO-K Ordering Information RUVAC (WA/WAU/WS/WSU possible) Backing pump SCREWLINE P P1 RUTA WAU 001/SP630/A WAU 001 SP630 Pump system, complete (adaptor version), pallet mounted, with Roots vacuum pump RUVAC WAU Frequency inverter RUVATRONIC (see description in Section Accessories ) Part No RT 5/001 Part No Presure mbar WAU001 + SP630 6 min 8 Pump-down time Pump-down time diagram for a 10 m 3 tank at 50 Hz Pumping speed 10 m 3. h mbar Pressure Pumping speed diagram at 50 Hz WAU001 + SP C08
18 Dry-Compressing Vacuum Pump System RUTA with SCREWLINE SP630 Backing Pump, Frame Version RUTA WAU 001/SP630/G Standard Equipment - Silencer - SP Guard - Manually operated gas ballast - SECUVAC valve V DC - Gear oil collecting pan integrated within the SCREWLINE - Crane eyes on the frame - Floor mounting - Gear oil supplied with the pump - CE approval Options - Frequency inverter RUVATRONIC RT for controlling the speed of the Roots pump - Condensate drain valve at the silencer - Sound proofing box - Vibration absorbers - SCREWLINE with water cooling - Castors - Different types of floor mounts - Oil drain valve on each pump - Electric control systems b l1 b1 b DN1 DN h h h1 l l b3 b* 1) RUTA 001/SP630/G 3001/SP630/G 5001/SP630/G 7001/SP630/G 9001/SP630/G RUVAC RA P RUVAC WA/WAU/WS/WSU P 001 Backing pump SCREWLINE P1 SP630 SP630 SP630 SP630 SP630 DN ISO-K 50 ISO-K 50 ISO-K 50 ISO-K 30 ISO-K DN 100 ISO-K 100 ISO-K 100 ISO-K 100 ISO-K 100 ISO-K l 00 (86.6) 00 (86.6) 00 (9.9) 00 (9.9) 00 (9.9) l (3.6) 600 (3.6) 70 (8.35) 70 (8.35) 70 (8.35) l 89 (35.1) 89 (35.1) 101 (39.8) 101 (39.8) 101 (39.8) b 106 (1.89) 106 (1.89) 119 (.5) 119 (.5) 119 (.5) b 1 00 (15.75) 00 (15.75) 65 (18.31) 65 (18.31) 65 (18.31) b 55 (1.81) 55 (1.81) 55 (1.81) 55 (1.81) 55 (1.81) b (31.50) 800 (31.50) 930 (36.61) 930 (36.61) 930 (36.61) b 70 (.76) 70 (.76) h 1789 (70.3) 030 (79.9) 0 (87.0) 0 (87.0) 300 (90.55) h (5.33) 1380 (5.33) 10 (56.69) 10 (56.69) 10 (56.69) 1) Clearance for maintenance h 159 (9.57) 115 (55.71) 175 (58.07) 175 (58.07) 175 (58.07) Dimensional drawing of the pump systems with dry compressing SCREWLINE SP630 backing pump, frame version; dimensions in brackets ( ) are in inch C08 18
19 Technical Data, 50 Hz RUVAC RA RUVAC (WA/WAU/WS/WSU possible) Backing pump SCREWLINE P P P1 RUTA RA 001/SP630/G 3001/SP630/G 5001/SP630/G 7001/SP630/G 9001/SP630/G SP630 SP630 SP630 SP630 SP630 Pumping speed, 50 Hz at 10-1 mbar (7.5 x 10 - Torr) Ultimate total pressure without gas ballast Installed motor power Electrical power consumption at 10-1 mbar (7.5 x 10 - Torr) m 3 x h -1 (cfm) mbar (Torr) 1780 (1050) 380 (1930) 510 (660) 590 (3500) 690 (070) < 1 x 10-3 < 1 x 10-3 < 1 x 10-3 < 1 x 10-3 < 1 x 10-3 (< 7.5 x 10 - ) (< 7.5 x 10 - ) (< 7.5 x 10 - ) (< 7.5 x 10 - ) (< 7.5 x 10 - ).5 (30.0) 6.0 (35.0) 30.0 (0.0) 33.5 (5.0) 37.0 (50.0) 11.7 (15.7) 1. (16.) 1.6 (16.9) 13.0 (17.) 13.5 (18.1) Noise level to DIN with silencer at 10-1 mbar (7.5 x 10 - Torr) db(a) Weight, total, approx. kg (lbs) 1300 (870) 1550 (30) 1900 (190) 000 (10) 630 (5800) Connecting flange Inlet port DN 1 Outlet port DN 160 ISO-K 50 ISO-K 50 ISO-K 50 ISO-K 30 ISO-K 100 ISO-K 100 ISO-K 100 ISO-K 100 ISO-K 100 ISO-K Ordering Information RUVAC P RUVAC (WA/WAU/WS/WSU possible) P Backing pump SCREWLINE P1 Pump system, complete (adaptor version), frame mounted, with Roots vacuum pump RUVAC WAU RUVAC RA with water-cooled vacuum pump SCREWLINE SP630 F Frequency inverter RUVATRONIC (see description in Section Accessories ) RUTA RA 001/SP630/G 3001/SP630/G 5001/SP630/G 7001/SP630/G 9001/SP630/G RA 3001 RA 5001 RA 7001 RA 9001 WAU 001 SP630 SP630 SP630 SP630 SP630 Part No Part No. Part No. Part No. Part No Part No. Part No. Part No. Part No. Part No RT 5/001 RT 5/3001 RT 5/5001 RT 5/7001 RT 5/9001 Part No. Part No. Part No. Part No. Part No ) ) ) ) 1) With this combination, continouos operation of the Roots pump is not possible at atmospheric pressure Presure mbar WAU001 + SP630 RA SP RA SP630 6 RA SP630 RA SP min 8 Pump-down time Pump-down time diagram for a 10 m 3 tank at 50 Hz Pumping speed 10 m 3. h WAU001 + SP630 RA SP630 RA SP630 RA SP630 RA SP mbar Pressure Pumping speed diagram at 50 Hz 19 C08
20 RUVAC RAV Roots Vacuum Pumps with Pre-Admission Cooling Typical Applications - Short pump-down cycles on large volumes - Oil-free compression of high volume flows of gases and vapors against atmospheric pressure - Single-stage (G) or in combination with RAV F as backing pump - Operating pressures in the rough vacuum range - CE approval Advantages to the User - RUVAC RAV G Operating pressure range of 150 mbar (11.5 Torr) against atmospheric pressure; total leak rate < 10-1 mbar x l x s -1 (7.5 x 10 - Torr x l x s -1 ) - RUVAC RAV F In combination with backing pumps the attainable operating pressures extend down into the medium vacuum range; leak rate < 10 - mbar x l x s -1 (7.5 x 10-3 Torr x l x s -1 ) - When series-connected the operating pressures extend down into the medium vacuum range: - two-stages to 5 mbar (18.75 Torr) - multiple stage to 10-3 mbar (7.5 x 10 - Torr) - Motors for special supply voltages and frequencies or protected types are available - Pre-admission silencer and filter for the cooling gas inlet as well as silencers for the exhaust side (option/single-stage) - Downstream gas cooler (option/ multistage) - C version (chemical version/ option) - Special materials (option) - Pressure burst resistant version (option) l b l 1 l 5 l 6 b DN 1 l l 3 DN h d h1 10 DN b b 3 1 l Cooling water connection for RAV 000 F, RAV 8000 F DN DN 1 Type F Type G RUVAC RAV DIN 533 DIN 533 l l 1 l l 3 l l 5 l 6 b b 1 b b 3 d d h h F/G mm k6 8 k in k k F/G mm k6 38 k in k k F/G mm k6 5 k in k k F/G mm k6 55 k in k6.17 k F/G mm 50 1) k6 70 m in. 50 1) k6.76 m F/G mm 300 1) 00 1) k6 90 m in ) 00 1) k6 3.5 m ) DIN 53 DN 1 = Pre-inlet Dimensional drawing for the RUVAC RAV pumps C08 0
21 Technical Data, 50 Hz Pumping speed 1) Ordering Information Ordering Information m 3 x h -1 (cfm) Nominal speed min -1 (rpm) Max. permissible pressure difference ) mbar (Torr) Connecting flange Max. permissible motor power for direct drive for belt drive Weight Roots vacuum pump RUVAC RAV G Technical Data, 50 Hz Pumping speed 1) DN kg (lbs) m 3 x h -1 (cfm) Nominal speed min -1 (rpm) Max. permissible pressure difference ) mbar (Torr) Connecting flange Max. permissible motor power for direct drive for belt drive Gear oil, approx. Weight, approx. DN l (qt) kg (lbs) Cooling water connection, fitting for tube Cooling water requirement, approx. l x h -1 Roots vacuum pump RUVAC RAV F 1) To DIN 8 00 and following numbers ) RUVAC RAV G and RAV F with direct drive RUVAC RAV 50 G 500 G 1000 G 000 G 000 G 8000 G 50 (17) 500 (95) 1000 (589) 000 (1178) 3700 (179) 8100 (771) 3000 (3000) 3000 (3000) 3000 (3000) 3000 (3000) 1500 (1500) 1500 (1500) 850 (637) 850 (637) 850 (637) 850 (637) 850 (637) 850 (637) (15.0) 18.5 (5.) 30.0 (0.8) 55.0 (7.8) 95.0 (19.3) 00.0 (7.1) 11.0 (15.0) 18.5 (5.) 30.0 (0.8) 55.0 (7.8) 95.0 (19.3) 00.0 (7.1) 95 (10) 160 (353) 5 (96) 310 (68) 70 (1588) 130 (71) RUVAC RAV 50 G 500 G 1000 G 000 G 000 G 8000 G upon request upon request upon request upon request upon request upon request RUVAC RAV 50 F 500 F 1000 F 000 F 000 F 8000 F 50 (17) 500 (95) 1000 (589) 000 (1178) 3700 (179) 8100 (771) 3000 (3000) 3000 (3000) 3000 (3000) 3000 (3000) 1500 (1500) 1500 (1500) 850 (637) 850 (637) 850 (637) 850 (637) 850 (637) 850 (637) (15.0) 18.5 (5.) 30.0 (0.8) 55.0 (7.8) 95.0 (19.3) 00.0 (7.1).0 (5.).0 (5.) 7.5 (10.) 15.0 (0.) 37.0 (50.3) 75 (10.0) 0.9 (0.95) 1.1 (1.6) 1.5 (1.59).5 (.6) 1.0 (1.68) 11.0 (11.63) 95 (10) 160 (353) 5 (96) 310 (68) 70 (1588) 130 (71) 10 x 1 10 x RUVAC RAV 50 F 500 F 1000 F 000 F 000 F 8000 F upon request upon request upon request upon request upon request upon request 10 Torr m x h -1 RAV 8000 G RAV 000 G 5000 cfm Pumping speed 8 6 RAV 000 G RAV 1000 G RAV 500 G RAV 50 G mbar Pressure Pumping speed diagram of RUVAC RAV at 50 Hz Operating diagram of RUVAC RAV vacuum pumps with pre-admission cooling 1 C08
22 RUTA RAV Pump Systems with RUVAC RAV Roots Vacuum Pumps, Two-Stage Standard Equipment - Roots vacuum pumps with preadmission cooling - One or two RAV F pumps are connected upstream of the RUVAC RAV G pump operating as a backing pump - Ultimate pressures below 50 mbar (37.5 Torr) can be attained - Gas cooler, pre-admission silencer and filter - Non-return flap - Exhaust silencer - CE approval b 1 DN 1 h h h3 DN h h1 h h3 DN h h1 h l b l l 1 l b l 1 l RUTA 500 F/50 G 1000 F/500 G 000 F/1000 G 000 F/000 G 8000 F/000 G RUVAC RAV P 500 F 1000 F 000 F 000 F 8000 F RUVAC RAV P1 50 G 500 G 1000 G 000 G 000 G DN (3.9) 100 (3.9) 150 (5.91) 50 (9.8) 300 (11.81) DN 80 (3.15) 100 (3.9) 100 (3.9) 150 (5.91) 50 (9.8) l 190 (50.79) 1560 (61.) 1830 (7.03) 00 (9.9) 790 (109.8) l 1 0 (16.5) 80 (18.90) 570 (.) 800 (31.50) 950 (37.0) l 1050 (1.3) 1100 (3.31) 1300 (51.18) 1650 (6.96) 150 (8.65) b 1300 (51.18) 1500 (59.06) 1680 (66.1) 050 (80.71) 600 (10.36) b (1.3) 1180 (6.6) 1300 (51.18) 1550 (61.0) 100 (8.68) b 00 (15.75) 00 (15.75) 50 (17.7) 500 (19.69) 700 (7.56) h 1550 (61.0) 1700 (66.93) 1930 (75.98) 550 (100.39) 3100 (1.05) h 1 70 (8.35) 80 (3.8) 1000 (39.37) 1100 (3.31) 100 (7.) h 500 (19.69) 570 (.) 750 (9.53) 700 (7.56) 700 (7.56) h (6.6) 130 (5.76) 150 (60.63) 1750 (68.90) 100 (8.68) h 1370 (53.9) 150 (59.8) 1750 (68.90) 10 (87.01) 500 (98.3) Dimensional drawing for two-stage RUTA RAV pump systems; dimensions in brackets ( ) are in inch C08
23 Technical Data, 50 Hz RUVAC RAV P RUVAC RAV P1 Pumping speed, 50 hz at 00 mbar (150 Torr) m 3 x h -1 (cfm) at 100 mbar (75 Torr) m 3 x h -1 (cfm) Ultimate total pressure mbar (Torr) (other motors are required) Cut-in pressure P 1) mbar (Torr) P1 mbar (Torr) Installed motor power Power consumption at 00 mbar (150 Torr) Cooling water consumption (T < 30, T < 10 K), max. (gas coolers and pumps) m 3 x h -1 (cfm) Noise level to DIN with pre-inlet and pulsation silencers and pump exhaust leading outside db(a) plus additional sound proofing box db(a) (a further reduction is possible) Gear oil, approx. l (qt) Total weight, incl. silencers for preadmission and exhaust, approx. kg (lbs) Connecting flange (pipe connection) ) Inlet port DN 1 Outlet port DN Gas admission port without filter DN Ordering Information Pump system 500 F/ 50 G 1000 F/ 500 G RUTA RAV 000 F/ 1000 G 000 F/ 000 G 8000 F/ 000 G 500 F 1000 F 000 F 000 F 8000 F 50 G 500 G 1000 G 000 G 000 G 3.0 (189.7) (17.0) (89.1) (1581.5) (38.6) < 50.0 (< 37.5) < 50.0 (< 37.5) < 50.0 (< 37.5) < 50.0 (< 37.5) < 50.0 (< 37.5) (3.0) (03.5) 58.0 (11.0) (7.5) 50.0 (376.5) (760.0) (760.0) (760.0) (760.0) (760.0) 15.0 (0.).0 (9.9).0 (59.9) 8.0 (111.6) (.5) 7.8 (10.6) 15.8 (1.5) 31.5 (.9) 56. (76.7) 1.0 (166.0) 0.5 (0.3) 1.0 (0.6).0 (1.) 3.0 (1.8) 7.0 (.1) (.11).5 (.6).0 (.3) 1.5 (15.33) 3.0 (.31) 1000 (05) 1600 (358) 00 (851) 000 (880) 7500 (16538) F/ 50 G 1000 F/ 500 G RUTA RAV 000 F/ 1000 G 000 F/ 000 G 8000 F/ 000 G upon request upon request upon request upon request upon request 1) With exhaust flap and bypass line 1013 mbar (760 Torr) ) to DIN 5 33 mbar Pressure Torr min 0 5 RAV 8000 F + RAV 000 G RAV 000 F + RAV 000 G Time 3 RAV 000 F + RAV 1000 G RAV 1000 F + RAV 500 G 1 RAV 500 F + RAV 50 G m 3 x h -1 Pumping speed Torr mbar Pressure 5000 cfm RAV 8000 F + RAV 000 G RAV 000 F + RAV 000 G 3 RAV 000 F + RAV 1000 G RAV 1000 F + RAV 500 G 1 RAV 500 F + RAV 50 G 5 RAV 8000 F + RAV 000 G RAV 000 F + RAV 000 G 3 RAV 000 F + RAV 1000 G RAV 1000 F + RAV 500 G 1 RAV 500 F + RAV 50 G Pump-down time diagram for a 50 m 3 tank for RAV F+G at 50 Hz Pumping speed diagram of RAV F + G at 50 Hz 3 C08
24 RUTA RAV Pump Systems with RUVAC RAV Roots Vacuum Pumps, Three-Stage Standard Equipment - Roots vacuum pumps with preadmission cooling - Two RAV F pumps are connected upstream of the RUVAC RAV G pump operating as a backing pump - CE approval - Ultimate pressures below 10 mbar (7.5 Torr) can be attained - Gas cooler, pre-admission silencer and filter - Non-return flap - Exhaust silencer b 1 b 1 DN 1 DN 1 h h h h3 DN h h h1 b l b l 1 l b b RUTA 1000 F/500 F/50 G 000 F/1000 F/500 G 000 F/000 F/1000 G 8000 F/000 F/000 G RUVAC RAV P F 000 F 000 F 8000 F RUVAC RAV P 500 F 1000 F 000 F 000 F RUVAC RAV P1 50 G 500 G 1000 G 000 G DN (3.9) 150 (5.91) 50 (9.8) 300 (11.81) DN 80 (3.15) 100 (3.9) 100 (3.9) 150 (5.91) l 1560 (61.) 1830 (7.05) 00 (9.9) 790 (109.8) l 1 80 (18.90) 570 (.) 800 (31.50) 950 (37.0) l 1050 (1.3) 1100 (3.31) 1350 (53.15) 1650 (6.96) b 170 (85.3) 00 (9.9) 850 (11.0) 300 (133.86) b (7.83) 000 (78.7) 00 (9.9) 950 (116.1) b 00 (15.75) 00 (15.75) 50 (17.7) 500 (19.69) h 170 (67.7) 1950 (76.77) 550 (100.39) 3000 (118.11) h (31.5) 1000 (39.37) 1150 (5.8) 100 (7.) h 600 (3.6) 750 (9.53) 850 (33.6) 850 (33.6) h (50.39) 1500 (59.06) 1700 (66.93) 1830 (7.05) h 150 (59.8) 1750 (68.90) 10 (87.01) 500 (98.3) Dimensional drawing for three-stage RUTA RAV pump systems; dimensions in brackets ( ) are in inch C08
25 Technical Data, 50 Hz RUVAC RAV P3 RUVAC RAV P RUVAC RAV P1 Pumping speed, 50 Hz at 00 mbar (150 Torr) m 3 x h -1 (cfm) at 100 mbar (075 Torr) m 3 x h -1 (cfm) Ultimate total pressure mbar (Torr) (other motors are required) Cut-in pressure P3 1) mbar (Torr) P 1) mbar (Torr) P1 mbar (Torr) Installed motor power Power consumption at 100 mbar (75 Torr) Cooling water consumption (T < 30, T < 10 K), max. (gas coolers and pumps) m 3 x h -1 (cfm) Noise level to DIN with pre-inlet and pulsation silencers and pump exhaust leading outside db(a) plus additional sound proofing box db(a) (a further reduction is possible) Gear oil, approx. l (qt) Total weight, incl. silencers for preadmission and exhaust, approx. kg (lbs) Connecting flange (pipe connection) ) Inlet port DN 1 Outlet port DN Gas admission port without filter DN 1000 F/ 500 F/ 50 G 000 F/ 1000 F/ 500 G RUTA RAV 000 F/ 000 F/ 1000 G 8000 F/ 000 F/ 000 G 1000 F 000 F 000 F 8000 F 500 F 1000 F 000 F 000 F 50 G 500 G 1000 G 000 G 71.0 (36.) (96.5) 86.0 (1685.7) 63.0 (3677.1) < 10.0 (< 7.5) < 10.0 (< 7.5) < 10.0 (< 7.5) < 10.0 (< 7.5) 78.0 (08.5) 65.0 (198.8) 31.0 (3.0) 89.0 (16.8) (3.0) (03.5) 58.0 (11.0) (7.5) (760.0) (760.0) (760.0) (760.0).5 (30.6) 37.0 (50.3) 6.5 (85.0) (13.6) 1.0 (16.3). (33.).3 (57.6) 90.6 (13.3) 1.0 (0.6).0 (1.).0 (.) 8.0 (.7) (3.70) 5.0 (5.9) 16.0 (16.91) 5.0 (6.3) 000 (10) 3000 (6615) 5000 (1105) 8500 (1873) Ordering Information Pump system 1000 F/ 500 F/ 50 G 000 F/ 1000 F/ 500 G RUTA RAV 000 F/ 000 F/ 1000 G 8000 F/ 000 F/ 000 G upon request upon request upon request upon request 1) With exhaust flap and bypass line 1013 mbar (760 Torr) ) to DIN Torr Pressure mbar min 0 Time Torr RAV 8000 F + RAV 000 F + RAV 000 G 3 RAV 000 F + RAV 000 F + RAV 1000 G RAV 000 F + RAV 1000 F + RAV 500 G 1 RAV 1000 F + RAV 500 F + RAV 50 G Pump-down time diagram for a 50 m 3 tank for RAV F, F + G at 50 Hz m 3 x h -1 Pumping speed mbar Pressure Pumping speed diagram of RAV F, F + G at 50 Hz 5000 cfm RAV 8000 F + RAV 000 F + RAV 000 G 3 RAV 000 F + RAV 000 F + RAV 1000 G RAV000F+RAV1000 F + RAV 8000 F + RAV 000 F + RAV 000 G 3 RAV 000 F + RAV 000 F + RAV 1000 G RAV 000 F + RAV 1000 F + RAV 500 G 1 RAV 1000 F + RAV 500 F + RAV 50 G 5 C08
26 TVD Pump Systems for Drying, Evaporation and Distillation Applications TVD 00 Advantages to the User - Operating agent may be reused, for example by returning cleaned water to the process - Reduction of the quantities which need to be disposed of by 80% - Low temperature distillation/drying - Condensate may be drained during vacuum operation - CE approval Typical Applications - Drying of powders and solids, for example - Cleaning of waste water - Vacuum distillation Standard Equipment - Condenser at the intake side - Receiver with condensate level indicator - Manually operated valves on the receiver - SOGEVAC rotary vane pump with integrated exhaust filters, antisuckback valve and gas ballast valve DN3 l 1 Hand Handventil valve DN 63 ISO-K DN1 b1 b Options - Valve between condenser and rotary vane pump DN 3 DN h1 h DN 3 h c l b DN 1 DN DN 3 l l 1 b b 1 b h h 1 h c TVD 00 mm 63 ISO-K 1 1/" 1" in. 63 ISO-K 1 1/" 1" TVD 065 mm 63 ISO-K 1 1/" 1" in. 63 ISO-K 1 1/" 1" TVD 100 mm 100 ISO-K " 1" in. 100 ISO-K " 1" TVD 00 mm 100 ISO-K " 1" in. 100 ISO-K " 1" Pressure gauge for checking the condensate pressure - Solenoid valves at the receiver - Receiver with proximity switch for monitoring the condensate level - Electric control for automatic operation of the pump system - Mobile pallet with castors - Cold water replacement for mobile applications Dimensional drawing for the TVD pump systems C08 6
27 Technical Data, 50 Hz TVD 0 TVD 65 TVD 100 TVD 00 Condenser, effective surface area, approx. m Receiver, usable volume Rotary vane vacuum pump Nominal pumping speed Pumping speed at 50 Hz for air for water vapor at 50 mbar (37.5 Torr) Ultimate total pressure with standard gas ballast Noise level to DIN ) l (qt) SOGEVAC m 3 x h -1 (cfm) m 3 x h -1 (cfm) m 3 x h -1 (cfm) mbar (Torr) db(a) 30.0 (31.71) 50.0 (5.85) 50.0 (5.85) 50.0 (5.85) SV 0 SV 65 SV 100 SV (7.1) 65.0 (38.3) (58.9) (106.0) 6.0 (7.1) 53.0 (31.) 9.0 (55.) (100.1) 80.0 (165.0) (330.0) 80.0 (95.0) (85.0) < 1.5 (< 1.1) < 1.5 (< 1.1) < 1.5 (< 1.1) < 0.7 (< 0.53) Condensing capacity for water l x h Installed motor power 1.1 (1.5) 1.5 (.0). (3.0).0 (.) 1) Operating at ultimate pressure with gas ballast Technical Data, 50 Hz Weight (with oil filling), approx. kg (lbs) Oil filling l (qt) Connecting flanges Inlet port DN 1 Outlet port DN SV 0 SV 65 SV 100 SV (76) 150 (331) 00 (1) 300 (66).0 (.11).0 (.11) 3.5 (3.70) 5.0 (5.9) 63 ISO-K 63 ISO-K 100 ISO-K 100 ISO-K 1 1/" 1 1/" " " Ordering Information TVD 0 TVD 65 TVD 100 TVD 00 Pump system Part No Part No Part No Part No C08
28 Pump Systems (Only available for purchase in North and South America) RBS - B/BCS Roots Pump Systems with Two-Stage TRIVAC Backing Pumps RBS - B/BCS Roots pumping system, shown with optional AF exhaust filter Standard Equipment - System consists of TRIVAC dual stage B or BCS direct drive vane pump and RUVAC blower - Complete air cooled system - 18 wide frame base equipped with caster wheels and leveling pads - Compact construction with quiet operation - Manual operation of gas ballast - Close-coupled RUVAC blower with ANSI inlet lange Options - All TRIVAC accessories, Exhaust filter, V DC gas ballast valve, chemical oil filter, and electrical limit switch system - Full frame drip pan - Oil drain valves - Special motor voltages and frequencies - Special oil for unique applications - Full electrical controls for control start/stop and monitoring of system 300 cfm 501/D65B Pumping Speed /D0B 51/D65B 51/D0B Torr Total Pressure Pumping speed diagram for the RBS systems with WSU series Roots blowers at 60 Hz C08 8
29 l 1 b b l 1 l h h 1 l l System Close-coupled b b 1 b h h 1 l l 1 l D 0 B/BCS WSU (57) 8 (03) 7 (178) 33 3/16 (853) 17 15/16 (56) 3 3/ (83) 1 (356) 3 (86) WSU (57) 8 (03) 7 (178) 3 3/ (883) 17 15/16 (56) 33 13/16 (859) 1 (356) 3 (86) D 65 B/BCS WS/WSU (57) 8 (03) 7 (178) 33 3/16 (853) 17 15/16 (56) 3 3/ (883) 16 (06) 3 (86) WS/WSU (57) 8 (03) 7 (178) 3 3/ (883) 17 15/16 (56) 35 13/16 (910) 16 (06) 3 (86) Dimensional drawing for the RBS - B/BCS Roots pumping pystems 18 with TRIVAC D 0/65 B backing pumps, close-coupled package; dimensions in brackets ( ) are in mm 9 C08
30 Technical Data RUVAC (WA/WAU/WS/WSU possible) TRIVAC backing pump Pumping 0.1 Torr cfm (m 3 x h -1 ) RBS - B/BCS Roots Pump Systems 51/D0B 51/D65B 501/D0B 501/D65B D 0 B/BCS D 65 B/BCS D 0 B/BCS D 65 B/BCS 10 (37) 150 (5) 3 (39) 67 (53) Ultimate total pressure Connecting flanges Inlet port WSU Outlet port Operating voltage Phase / Frequency 1) Full load amps ) RUVAC WSU TRIVAC Torr (mbar) DN DN V / Hz x 10 - x 10 - x 10 - x 10 - (< x 10 - ) (< x 10 - ) (< x 10 - ) (< x 10 - ) 3" ANSI 3" ANSI 3" ANSI 3" ANSI 0 ISO-KF 0 ISO-KF 0 ISO-KF 0 ISO-KF 08/30/60 08/30/60 08/30/60 08/30/60 3 / 60 3 / 60 3 / 60 3 / /5.5/3. 5.5/5.5/3. 9.0/9.0/5. 9.0/9.0/5. 9.0/8.8/.5 9.0/8.8/.5 9.0/8.8/.5 9.0/8.8/.5 Displacement RUVAC cfm (m 3 x h -1 ) TRIVAC cfm (m 3 x h -1 ) 179 (30) 179 (30) 357 (606) 357 (606) 3 (5) 53 (90) 3 (5) 53 (90) Maximum differential pressure Normal starting pressure 3) Oil capacity RUVAC WSU TRIVAC Torr (mbar) Torr (mbar) qt (l) qt (l) 60 (80) 60 (80) 60 (80) 60 (80) 0 (7) 30 (0) 1 (16) 16 (1) 0.75 (0.7) 0.75 (0.7) 1.10 (1.0) 1.10 (1.0).70 (.6) 3.0 (3.).70 (.6) 3.0 (3.) Nominal rotation speed RUVAC rpm (min -1 ) TRIVAC rpm (min -1 ) 3600 (3600) 3600 (3600) 3600 (3600) 3600 (3600) 1800 (1800) 1800 (1800) 1800 (1800) 1800 (1800) Motor power RUVAC WSU TRIVAC Ordering Information RBS - B/BCS Roots pump system (supplied with hydrocarbon oil) hp (kw) hp (kw) 1.9 (1.) 1.9 (1.) 3.3 (.) 3.3 (.) 3.0 (.) 3.0 (.) 3.0 (.) 3.0 (.) RBS - B/BCS Roots Pump Systems 51/D0B 51/D65B 501/D0B 501/D65B Ordering Information see right page 1) For 50 Hz systems, consult the factory ) Determined by operating voltage 3) WSU pumps permit start-up at atmospheric pressure (760 Torr) C08 30
31 Ordering Information Part No V- 0 Blower / TRIVAC pump WSU 51 / D 0 B WSU 51 / D 0 BCS-PFPE WSU 51 / D 65 B WSU 51 / D 65 B-PFPE WSU 501 / D 0 B WSU 501 / D 0 BCS-PFPE WSU 501 / D 65 B WSU 501 / D 65 BCS-PFPE Reserved Electrical Control Panel None 08 V 30 V 60 V C08
32 Pump Systems (Only available for purchase in North and South America) HTS Close-Coupled Systems with Single-Stage SOGEVAC Backing Pumps HTS close-coupled system Standard Equipment - System consists of single stage SOGEVAC vane pump - Complete air cooled system - Close-coupled RUVAC blower - Compact construction with quiet operation - Manual operation of gas ballast - Spin-on type oil filter Options - SOGEVAC accessories: oil level monitoring, exhaust case gauge, V DC gas ballast purge, watercooling - Frame base mounted caster wheels - Frame base mounted leveling pads - Oil drain valves - Inlet dust filter - External OF3000 oil filter - Special motor voltages and frequencies - Special oil for unique applications - Full NEMA1 electrical controls for stand/stop operation and monitoring of system from remote and local locations - V DC gas ballast valve cfm /SV300 cfm 001/SV630 Pumping Speed /SV00 501/SV /SV00 Pumping Speed /SV Torr Total Pressure Torr Total Pressure Pumping speed diagram for the HTS close-coupled systems with WSU series Roots blowers and SOGEVAC SV 00/300 at 60 Hz Pumping speed diagram for the HTS close-coupled systems with WSU series Roots blowers and SOGEVAC SV 630 at 60 Hz C08 3
33 Dimensions for SV 00 and SV 300 only l 1 w 3 w l l 1 h 1 h w 1 T SIDE VIEW FRONT VIEW Dimensions for SV 630 only l 1 l W W 3 l 3 h 1 h l 6 W 1 l 5 Roots Pump Vane Pump h 1 h l 1 l l 3 l 5 l 6 w 1 w w 3 WSU 501 SV /16 (78) 1 17/3 (318) 9 17/3 () 1 11/16 (551) 6 1/8 (156) 10 19/3 (69) WSU 501 SV /16 (78) 1 17/3 (318) 9 17/3 () 1 11/16 (551) 6 1/8 (156) 10 19/3 (69) WSU 1001 SV /16 (799) 1 17/3 (318) 11 15/16 (303) 1 1/16 (535) 5 1/ (10) 10 19/3 (69) M.019-E (WAU/WSU+SV) WSU 1001 SV /16 (799) 1 17/3 (318) 11 15/16 (303) 13/16 (579) 7 1/ (18) 10 19/3 (69) WSU 001 SV /16 (17) 3 13/16 (605) 50 3/16 (175) 1 9/16 (370) 60 3/ (153) 1/ (6) 3 15/16 (887) 13 7/8 (35) 1 13/3 (315) Dimensional drawing for the HTS close-coupled system with single-stage SOGEVAC backing pumps; dimensions in brackets ( ) are in mm 33 C08
34 Technical Data RUVAC SOGEVAC Pumping 0.1 Torr cfm (m 3 x h -1 ) HTS Close-Coupled Systems 501/SV00 501/SV /SV /SV300 WSU 501 WSU 501 WSU 1001 WSU 1001 SV 00 SV 300 SV 00 SV (70) 85 (83) 50 (855) 55 (95) Ultimate total pressure Connecting flanges Inlet port WSU Exhaust port SOGEVAC Operating voltage Phase / Frequency 1) Full load amps ) RUVAC WSU SOGEVAC Torr (mbar) DN DN V / Hz < 8 x 10-3 < 8 x 10-3 < 8 x 10-3 < 8 x 10-3 (< 1 x 10 - ) (< 1 x 10 - ) (< 1 x 10 - ) (< 1 x 10 - ) 3" ANSI 3" ANSI " ANSI " ANSI " NPT " NPT " NPT " NPT 08/30/60 08/30/60 08/30/60 08/30/60 3 / 60 3 / 60 3 / 60 3 / /10.0/ /10.0/ /1.7/ /1.7/ /18.0/ /5.0/ /18.0/ /5.0/1.5 Displacement RUVAC cfm (m 3 x h -1 ) SOGEVAC cfm (m 3 x h -1 ) 357 (606) 357 (606) 707 (100) 707 (100) 130 (606) 00 (30) 130 (606) 00 (30) Oil capacity RUVAC WSU SOGEVAC qt (l) qt (l) 1.10 (1.00) 1.10 (1.00).10 (.00).10 (.00) 5.30 (5.00) 9.00 (8.50) 5.30 (5.00) 9.00 (8.50) Nominal rotation speed RUVAC WAU/WSU rpm (min -1 ) SOGEVAC rpm (min -1 ) 3600 (3600) 3600 (3600) 3600 (3600) 3600 (3600) 1800 (1800) 1800 (1800) 1800 (1800) 1800 (1800) Motor power RUVAC WSU SOGEVAC Ordering Information HTS - close-coupled systems 1) For 50 Hz systems, consult the factory ) Determined by operating voltage hp (kw) hp (kw) 3.3 (.) 3.3 (.) 6.0 (.) 6.0 (.) 7.5 (5.5) 10.0 (7.) 7.5 (5.5) 10.0 (7.) HTS Close-Coupled Systems 501/SV00 501/SV /SV /SV300 Ordering Information see right page C08 3
35 Technical Data RUVAC SOGEVAC Pumping 0.1 Torr cfm (m 3 x h -1 ) HTS Close-Coupled Systems 1001/SV /SV SV 630 SV (1035) 1186 (031) Ultimate total pressure Connecting flanges Inlet port WSU Outlet port Operating voltage Phase / Frequency 1) Full load amps ) RUVAC WSU SOGEVAC Torr (mbar) DN DN V / Hz < 8 x 10-3 < 8 x 10-3 (< 1 x 10 - ) (< 1 x 10 - ) " ANSI 6" ANSI " ANSI " ANSI / 60 3 / Displacement RUVAC cfm (m 3 x h -1 ) SOGEVAC cfm (m 3 x h -1 ) 707 (100) 19 (60) 95 (80) 95 (80) Oil capacity RUVAC WSU SOGEVAC qt (l) qt (l).10 (.0).0 (.0) 37.0 (35.0) 37.0 (35.0) Nominal rotation speed RUVAC WSU rpm (min -1 ) SOGEVAC rpm (min -1 ) 3600 (3600) 3600 (3600) 1170 (1170) 1170 (1170) Motor power RUVAC WSU SOGEVAC hp (kw) hp (kw) 6.1 (.5) 11. (8.) 5.0 (13.) 5.0 (13.) Ordering Information Part No V- Blower / TRIVAC pump WSU 501 / SV 00 WSU 501 / SV 300 WSU 1001 / SV 00 WSU 1001 / SV 300 WSU 1001 / SV 630 WSU 001 / SV 630 Casters & Levelers (SV 00 & SV 300 only) None Casters & Levelers Casters only Levelers only Electrical Control Panel None 08 V (SV 00 & SV 300 only) 30 V (SV 00 & SV 300 only) 60 V C08
36 Pump Systems (Only available for purchase in North and South America) SP Close-Coupled Systems with SCREWLINE Dry Compressing Backing Pumps SP close-coupled system Advantages to the User - Reduced maintenance and lower operating costs - Compact close-coupled design without frame - Oil free compression in multiple pump stages - Optimum leak tightness with WSU boosters - Air-cooled - Assembled and tested Standard Equipment - SP630 / WSU1001 close-coupled pump system offering 65 ACFM at 0.3 Torr vacuum - SP630 / WSU001 close-coupled pump system offering 135 ACFM at 0.3 Torr vacuum Options - Electrical controls - Exhaust silencer (loose) - Inlet filter (loose) The new SCREWLINE SP630 dry compressing screw-type vacuum pump is an environmentally friendly alternative to traditional oil-sealed rotary piston and vane vacuum pumps. This innovative and robust vacuum pump produces a pumping speed of 371 cfm and better than Torr vacuum. SP630 major advantages include improved environment, reduced maintenance, lower operating costs through less disposal and the elimination of expensive water cooling all with no oil contamination as the need for lubricating oil in the pumps' compression stage has been eliminated. When used in conjunction with the Leybold Vacuum WSU booster pumps, pumping speeds can be significantly increased while achieving oil-free compression in multiple vacuum pump stages. Leybold Vacuum WSU boosters offer a canned motor design, which eliminates the need for shaft seals and flanged-on motors. A vacuum tight can separates the motor rotor and stator coils. This unique Leybold Vacuum design provides the advantage of a more leak tight vacuum system. The WSU ver-sion booster incorporates a bypass valve feature, which allows for automatic adjustment to varying pressure differentials between the inlet and outlet of the pump. The result is elimination of costly pressure switches / amplifiers and faster pump down while starting at atmospheric pressure with the aforementioned SP630 vacuum pump. C08 36
37 l 1 l w 1 w w Available Exhaust Silencer h h 1 h l 3 l w 3 w Roots Pump Vane Pump h h 1 h l l 1 l WSU 1001 SP / (176) 7 7/8 (116) 1 7/16 (316) 68 1/ (170) 3 3/16 (818) 0 1/ (51) WSU 001 SP /3 (1366) 7 7/8 (116) 1 7/16 (316) 71 5/3 (1807) 3 13/16 (88) 0 1/ (51) Roots Pump Vane Pump l 3 w w 1 w w 3 w WSU 1001 SP / (705) 37 31/3 (96) 1 (305) 1 1/3 (550) 5 7/8 (657) 36 9/3 (937) WSU 1001 SP / (705) 1 31/3 (1066) 16 (06) 1 1/3 ( /8 (657) 36 9/3 (937) Dimensional drawing for the SP close-coupled system with SCREWLINE SP630 dry-compressing backing pumps cfm cfm Pumping speed Pumping Speed WSU SP 630 SP 630 Pumping speed Speed WSU SP 630 SP HV Pressure Torr HV Pressure Torr 37 Pumping speed diagram for the SP close-coupled system with WSU 1001 Roots blower and SCREWLINE SP630 at 60 Hz Pumping speed diagram for the SP close-coupled system with WSU 001 Roots blower and SCREWLINE SP630 at 60 Hz 37 C08
38 Technical Data, 60 Hz RUVAC (WSU possible) P SP Close-Coupled Systems 1001/SP /SP Backing pump SCREWLINE P1 SP630 SP630 Pumping speed 60 Hz at 0.3 Torr m 3 x h -1 (cfm) 65 (380) 135 (77) Ultimate total pressure without gas ballast Installed motor power mbar (Torr) < 1 x 10-3 (< 7.5 x 10 - ) < 1 x 10-3 (< 7.5 x 10 - ) 16. (1.6).5 (30.0) Noise level to DIN with silencer at 10-1 mbar (7.5 x 10 - Torr) db(a) Weight, total, approx. kg (lbs) 870 (19) 1100 (30) Connecting flange Inlet port DN 1 Outlet port DN 160 ISO-K 160 ISO-K 100 ISO-K 100 ISO-K Ordering Information RUVAC (WA/WAU/WS/WSU possible) P SP Close-Coupled Systems 1001/SP /SP630 WSU 1001 WSU 001 Backing pump SCREWLINE P1 SP630 SP630 Pump system, complete (adaptor version), pallet mounted, with Roots vacuum pump RUVAC WAU Part No V1600 Part No V600 C08 38
39 Notes 39 C08
40 Accessories Sound Proofing A sound proofing box is available as an optional extra so as to reduce the noise down to the permissible level. Depending on the size of the pumping system, noise reductions between 15 and 0 db(a) are obtained using our standard soundproofing arrangements. Custom designs of the sound proofing box allow the noise level to be reduced by up to 35 db(a). The maintenance side is designed as a door component. A window insert may be provided in the door or in the side walls to facilitate checking of the oil levels. Ventilation is performed by means of an electric fan, the fresh air and exhaust ducts are located within the sound proofing box. Further optional extras which may be fitted include closed air circulation with integrated, water-cooled heat exchanger and a connection port for a central exhaust system. Dust Separators Vacuum processes where large amounts of particles or dusts are contributed by the process require special devices to protect the vacuum pumps. Leybold Vacuum has developed even for high flow rate applications special dust separators, which can be installed ahead of the intake of the RUTA vacuum pump systems. The dust separators have two stages. The first stage is a cyclone that collects dust particles of coarse and medium size, the fine dust are trapped in filter elements. Dust separators are customdesigned for the specific process and the required pumping speed. Dust Filter without Cyclone See below. Diagrammatic section through a dust separator Filtering surface m suitable for pumping speeds min. m 3 x h -1 (cfm) 100 (58.9) 300 (176.7) 600 (353.) 1000 (589) 1500 (883.5) 3000 (1767) max. m 3 x h -1 (cfm) 300 (176.7) 800 (71.) 1500 (883.5) 3000 (1767) 000 (356) 8000 (71) Reduction of pumping speed at < 01 mbar (< 0.75 Torr) % < 06 mbar (<.5 Torr) % < 0 mbar (< 15 Torr) % without dust load C08 0 RUTA RA 3001/S630F/G with sound proofing box Isolation against Vibrations RUTA vacuum pump systems produce only slight vibrations. To reduce these vibrations even further, vibration absorbers can be fitted under the pump system. Frequency Inverter RUVATRONIC RT 5 The electronic frequency inverters RUVATRONIC RT 5/51 to 5/16000 have been designed specially for use in connection with Leybold Vacuum Roots pumps of the RUVAC type. For each Roots vacuum pump size, a matching frequency inverter is available. The main characteristics of the RUVATRONIC RT 5 are: Simulation of a pressure equalisation line The software of the frequency inverters is adapted to each pump and ensures that the risk of mechanically overloading the pump can be excluded. In the case of too high pressure differences, the rotational speed will be decreased automatically until the load is reduced to within the pump s limits. RUVAC Roots vacuum pumps of the types WA, WS and RA (without pressure equalisation line) can be switched on together with the forepump at atmospheric pressure. Through this, the pumpdown time can be reduced drastically. The minimum pumping speed of the backing pump needs to be considered in this case. Pump WA/WS 051 WA/WS 0501 WA/WS 1001 WA/WS 001 RA 3001 RA 5001 RA 7001 RA 9001 Required pumping speed for the backing pump 0050 m 3 /h (009 cfm) 0100 m 3 /h (0059 cfm) 000 m 3 /h (0118 cfm) 010 m 3 /h (01 cfm) 0650 m 3 /h (0383 cfm) 0930 m 3 /h (057 cfm) 150 m 3 /h (0736 cfm) 30 m 3 /h (1907 cfm)
41 Operation at up to 3 predefined speeds Via floating contacts, the pump can be operated at one of the 3 predefined speeds. Switching over to another pre-defined speed is possible during operation. Operation at any rotational speed With a 0 to 10 V signal, any speed can be pre-defined to operate the pump between the minimum and maximum rotational speed. The software reliably ensures that the rotational speed cannot drop below the minimum speed or exceed the maximum speed. Increase in the pumping speed By operating the Roots vacuum pumps at frequencies over 50 Hz, the nominal pumping speed of the pumps can be increased. Depending on the type of pump, an increase between 0 and 100% is possible. Note Please enquire about possible application limitations (process dependent). Electric Controller In order to drive all electrical appliances within the pump systems, the pump systems may be equipped with standard control cabinets which contain: - Motor protection switch (rated for the pumps used in each case) - Contactors - Main switch interlocked in accordance with VDE Relays for necessary control/ sub-systems - ON/OFF push-button for each pump - Power supply for the installed monitoring facilities - Fault indicators arranged on a lamp panel - Switch-over (through an external contact) from local to remote operation. The control cabinet may be fitted either to the frame of the pump system or it may be wallmounted. Beside the standard systems, we manufacture control systems for much more complex systems: - Remote control module as a 19" rack module (1/ width, 3 HU). The start/stop push-buttons and the related indicators for operation and fault are located on the front panel - Pre- and post-operation control - Pressure dependant control - Time-dependant control - Program control - Control for explosion hazard areas - Combinations of the aforementioned versions - Programmable control (PC) - Vacuum gauge with pressure read-out in the control cabinet. Pressure Control Basically there are several ways in which to control the pressure. The equipment which is supplied as standard for the DOWNSTREAM or BYPASS control systems selected by Leybold Vacuum consists of: - Pressure measurement - Controller with control unit - Control valve with position indicator - Engineering. The Downstream Control System throttles the pumping speed of the vacuum pump by changing the conductance of the valve. Control panel on RUTA WAU1001/SV00/G The advantages offered by this arrangement are: - No supply of other gases - Closed system - The intake pressure of the pump system is lower than its operating pressure (thus saving energy, among other things). The second method is the Bypass Control System. Here the pressure is maintained at a constant level by admitting an additional quantity of gas. The advantages offered by this arrangement are: - Simple design - Much smaller valve - No reduction of the intermediate pressure within the pump. In order to design a pressure control system we need the following information: - Amount of gas - Type of gas - Pressure - Length of the piping - Type of auxiliary energy (electric/ pneumatic) - Explosion protection required yes/no Additional complex control arrangements are available, for example with: - Adjustable pressure characteristic - Adjustable timing - Speed control - Combination with other control facilities. 1 C08
Vacuum Pump Systems RUTA
Vacuum Pump Systems RUTA 50-13 000 m 3 x h -1 (147 to 765 cfm) 173.0.0 Excerpt from the Product Section C08 Edition 010 AKTUELL 31.07.009 Contents General Overview.........................................................................
More informationC07 RUVAC. Roots Vacuum Pumps Single-Stage m 3 x h -1 ( cfm) vacuum
173.01.02 Excerpt from the Product Section Edition May 2005 RUVAC Roots Vacuum Pumps Single-Stage 250-13000 m 3 x h -1 (147.3-7657 cfm) vacuum Roots Vacuum Pumps Contents General Applications and Accessories..............................03
More informationRUVAC. Roots Vacuum Pumps. Single-Stage m 3 x h -1 ( cfm)
RUVAC Roots Vacuum Pumps Single-Stage 250-13 000 m 3 x h -1 (147-7657 cfm) 173.01.02 Excerpt from the Product Section C07 Edition 2010 Contents General Applications and Accessories.........................................................
More informationTRIVAC. Rotary Vane Vacuum Pumps, Oil-Sealed; 1.5 to 65 m 3 /h (0.7 to 38.3 cfm) S 1,5, Single-Stage. TRIVAC E, Two-Stage. TRIVAC NT, Two-Stage
TRIVAC Rotary Vane Vacuum Pumps, Oil-Sealed; 1.5 to 65 m 3 /h (0.7 to 38.3 cfm) S 1,5, Single-Stage TRIVAC E, Two-Stage TRIVAC NT, Two-Stage TRIVAC B, Two-Stage 171.01.02 Excerpt from the Product Section
More informationRoots Vacuum Pumps. Roots V. RUVAC Roots Vacuum Pumps
Roots Vacuum Pumps Roots V RUVAC Roots Vacuum Pumps 230.00.02 Excerpt from the Leybold Full Line Catalog 2016 Catalog Part Roots Vacuum Pumps Edition: Fall 2016 Contents Roots Vacuum Pumps General Applications
More informationRoots Vacuum Pumps. Roots V. RUVAC Roots Vacuum Pumps Excerpt from the Leybold Full Line Catalog 2018 Catalog Part Roots Vacuum Pumps
Roots Vacuum Pumps Roots V RUVAC Roots Vacuum Pumps 230.00.02 Excerpt from the Leybold Full Line Catalog 2018 Catalog Part Roots Vacuum Pumps 2 Leybold Full Line Catalog 2018 - Roots Vacuum Pumps leybold
More informationC02 SOGEVAC. Rotary Vane Vacuum Pumps single-stage, oil-sealed, m 3 x h -1 ( cfm)
C02 SOGEVAC single-stage, oil-sealed, 6-50 m 3 x h - (9.4-677 cfm) Contents General Product Range, Features and Design......................................... C02.03 Products SOGEVAC SV 6/SV 25.................................................
More informationTRIVAC NT, Two-Stage Rotary Vane Vacuum Pumps TRIVAC NT 5 to NT 25
TRIVAC NT, Two-Stage Rotary Vane Vacuum Pumps TRIVAC NT 5 to NT 25 (505)872-0037 The TRIVAC NT is the latest generation of well-proven rotary vane pumps. The performance and handling characteristics of
More informationTRIVAC NT 16 and NT 25
TRIVAC NT 16 and NT 25 idealvac.com (505)872-0037 idealvac.com TRIVAC NT 16 Type DN a b b1 c h h1 h2 l m n o NT 16 1) mm 25 KF 32 175 137 135 243 227 261 540 280 140 132 in. 25 KF 1.26 6.89 5.39 5.31 9.57
More informationProducts RUVAC WA/WAU 251 to 2001 Roots Vacuum Pumps with Air-Cooled Flange-Mounted Motors
Products RUAC WA/WAU 251 to 2001 Roots acuum Pumps with Air-Cooled Flange-Mounted Motors RUAC WAU 2001 single-stage Roots vacuum pump, depicted with a 160 ISO-K collar flange Advantages to the User - Two
More informationTurbomolecular Pump Systems TURBOLAB 80, 350, 450
Turbomolecular Pump Systems TURBOLAB 80, 350, 450 This new smart TURBOLAB generation is built on one basic design platform with the opportunity to create three different variants. Each version can be customized
More informationSOGEVAC FP Rotary Vane Pumps Proven Vacuum Technology for Food and Packaging Applications
172.190.02 SOGEVAC FP Rotary Vane Pumps Proven Vacuum Technology for Food and Packaging Applications The Benefits of SOGEVAC FP Pumps Pumping Water Vapor Water vapor tolerance adjustable to process conditions
More informationVacuum Pumps. Rotary Pumps F12 F13 F14 F15 F16 F17 F18 F19 F20 F21 F22 F23 F24
F Rotary Vacuum Pumps CONTENTS Vacuum Pumps Rotary Pumps Page F12 F13 F14 Edwards. RV Edwards. ES Edwards. EM. Small Edwards. EM. Medium Edwards. EM. Large F15 F16 F17 F18 F19 Oerlikon Leybold. S Oerlikon
More informationEurovacuum Installations and Operating manual EVD Series Vacuum pumps Models: EVD-6 to EVD-90. Double Stage Oil Lubricated Rotary Vane Vacuum Pump
Eurovacuum Installations and Operating manual EVD Series Vacuum pumps Models: EVD-6 to EVD-90 Double Stage Oil Lubricated Rotary Vane Vacuum Pump Eurovacuum EVD-Series Double Stage Oil Sealed Rotary Vane
More informationAGILENT ROTARY VANE PUMPS
AGILENT ROTARY VANE PUMPS 2-3 Features and Benefits 4-5 Typical Applications 6-9 Pump Models 20 Accessories 2 HS Series Pumps Features and Benefits 22-25 HS Series Pump Models 26-27 MS 40+ Pump Features
More informationVarian, Inc. Vacuum Technologies. Rotary Vane Pumps. Features and Benefits 2-3. Typical Applications 4-5. Pump Models 6-19.
Varian, Inc. Vacuum Technologies Rotary Vane Pumps Features and Benefits 2-3 Typical Applications 4-5 Pump Models 6-19 Accessories 20 Frequency Inverter Technology 21 HS Series Pumps 22-25 MS40+ Features
More informationCOBRA NC B. Dry Screw Vacuum Pumps. Standard Equipment. Description
Dry Screw Vacuum Pumps COBRA NC 0100-0300 B COBRA NC 0200 B Description The COBRA single stage, direct driven rotary screw dry vacuum pumps are designed for difficult applications in the pharmaceutical
More informationDual Stage Rotary Vane Pumps
VACUTEC P.O.BOX 48488 Roosevelt Park 2129 South Africa Tel: +27 (0) 11 475 1823 Fax: +27 (0) 11 475 1819 Email: sales@vacutec.co.za Dual Stage Rotary Vane Pumps Features and Benefits 16-17 Typical Applications
More informationGMK EV SERIES. Single Stage Oil Sealed Rotary Vane Pump
GMK EV SERIES Single Stage Oil Sealed Rotary Vane Pump EV Series Single Stage Oil Sealed Rotary Vane Pumps Eurovacuum Company is offering its various products to meet industrial vacuum needs. Eurovacuum
More informationSOGEVAC NEO D Three times a hit.
172..02 SOGEVAC NEO D Three times a hit. Less noise. Less emissions. Less maintenance. SOGEVAC NEO D The new generation of SOGEVAC vacuum pumps. Triple-hitting for cleaner, quieter, longer-running performance.
More informationAGILENT ROTARY VANE PUMPS
AGILENT 2-3 Features and Benefits 4- Typical Applications 6-9 Pump Models 20 Accessories 2 HS Series Features and Benefits 22-2 HS Series Pump Models 26-27 MS 40+ Pump Features and Benefits 28-29 MS 40+
More informationR5 Series Vacuum Pumps and Systems
R5 Series Vacuum Pumps and Systems R5 Series Rotary Vane Vacuum Pumps & Systems Duplex tank mounted system is one of many standard configurations. Duplex expandable model uses a common skid for mounting
More informationRUVAC WA / WAU 251/501/1001/2001
RUVAC WA / WAU 251/501/1001/2001 Roots vacuum pumps ATEX Categories 3 i and 3 i/o Installation and Operating Instructions GA03107_002_C0 Part Numbers 112 17/54 113 22/42 117 20/21/24/30/31/34/40/41/44
More informationVarian, Inc. Vacuum Technologies. TPS Turbo Pumping Systems. Features and Benefits 2-3. Mini-TASK AG TPS-compact 6-7
Varian, Inc. Vacuum Technologies TPS Turbo Pumping Systems Features and Benefits 2-3 Mini-TASK AG81 4-5 TPS-compact 6-7 TPS-mobile and TPS-bench 8-10 TPS Turbo Pumping Systems Features and Benefits The
More informationEverest. Leaders in Vacuum Booster Technology
EVEREST has introduced Mechanical Booster Pumps to meet the growing demand of the Vacuum Process Industry where fast pump down times are required and energy usage concerns rule out any alternative pump
More informationTRIVAC BCS. idealvac.com. Rotary Vane Vacuum Pump D 40 BCS, D 65 BCS. - with mineral oil filling or - with PFPE filling (505)
Vacuum Solutions Application Support Service LEYBOLD VACUUM GA 01.301/6.02 TRIVAC BCS Rotary Vane Vacuum Pump D 40 BCS, D 65 BCS - with mineral oil filling or - with PFPE filling Cat. No. 113 88/89/97/98/99
More informationC09. Turbomolecular Pumps l x s -1. vacuum
179.01.01 Excerpt from the Product Section Edition May 2005 Turbomolecular Pumps 35-3200 l x s -1 vacuum Turbomolecular Pumps Contents General General...............................................03 Applications...........................................12
More informationOPERATING INSTRUCTIONS GA01301_0702
OPERATING INSTRUCTIONS GA01301_0702 TRIVAC B D 40 BCS / D 65 BCS Rotary Vane Vacuum Pump with mineral oil with PFPE Part Nos. 113 88/89/98/99 154 52/54 vacuum Contents Section Page Important Safety Information....................................
More informationXDS Scroll Pumps 5. RV Rotary Vane Pumps 20. Small ATEX Certified Pumps 32. Electrical Data 36. Small Pump Accessories 36. E-LAB Rotary Pumps 41
Small Wet/Dry Pumps Small Pumps and Pumping Systems 2 Small Pumps: Application and Accessory Information 3 Small Pumps and Accessories: Frequently Asked Questions 4 XDS Scroll Pumps 5 E2M0.7 and.5 Oil
More informationAPPLIED VACUUM TECHNOLOGY. ASK THE EXPERTS!
4,6,8,16,24,30 APPLIED VACUUM TECHNOLOGY. ASK THE EXPERTS! www.welchvacuum.com/crvpro YOUR BENEFITS Highest reliability for stable operation and long product lifespan Reduced risk of chemical attacks and
More informationTRIVAC BCS. idealvac.com. Rotary Vane Vacuum Pump D 16 BCS, D 25 BCS. - with mineral oil filling or - with PFPE filling (505)
Vacuum Solutions Application Support Service LEYBOLD VACUUM GA 01.300/8.02 TRIVAC BCS Rotary Vane Vacuum Pump D 16 BCS, D 25 BCS - with mineral oil filling or - with PFPE filling Cat. No. 113 68/69 113
More informationSOGEVAC SV40 B - SV65 B - SV100 B
SOGEVAC SV40 B - SV65 B - SV100 B Single-stage, oil-sealed rotary vane pump Operating instructions 300267596_002_C0 Ref.: 960x00 to 960x07 960x11 to 960x14 960x16 to 960x19 960x20 to 960x24 and their variants
More informationTRIVAC B. Rotary Vane Vacuum Pump D 40 B, D 65 B. Operating Instructions GA / Cat. No / /46/47/55/56/57
Vacuum Solutions Application Support Service LEYBOLD VACUUM GA 01.203/10.02 TRIVAC B Rotary Vane Vacuum Pump D 40 B, D 65 B Cat. No. 112 86/96 113 45/46/47/55/56/57 Operating Instructions Contents Contents
More informationLEYBOLD VACUUM GA /10.02 TRIVAC E 2 D 5 E / D 10 E / D 16 E. Dual-Stage Rotary Vane Vacuum Pump. Operating Instructions
Vacuum Solutions Application Support Service LEYBOLD VACUUM GA 01.600/10.02 TRIVAC E 2 D 5 E / D 10 E / D 16 E Dual-Stage Rotary Vane Vacuum Pump Operating Instructions Contents Contents Page IMPORTANT
More informationVacuum Valves. Manually Operated Electropneumatically Operated Electromagnetically Operated Special Valves Gate Valves
Vacuum Valves Manually Operated Electropneumatically Operated Electromagnetically Operated Special Valves Gate Valves 176.01.02 Excerpt from the Product Section Edition December 2011 Contents General The
More informationDRYVAC. DV 450-i, DV 650-i, DV 1200-i, DVR 5000-i, DVR 5000-f Dry Compressing Vacuum Pumps. Operating Instructions _002_C0
DRYVAC DV 450-i, DV 650-i, DV 1200-i, DVR 5000-i, DVR 5000-f Dry Compressing Vacuum Pumps Operating Instructions 300304403_002_C0 Part Numbers 112045V50-1 112065V40-1 /45-1 /50-1 112120V40-1 /50-1 112500V40-1
More informationVARIO. VARIO Separation of fine dust particles. The VARIO series is particularly suitable for separation of fine dust.
VARIO VARIO Separation of fine dust particles The VARIO series is particularly suitable for separation of fine dust. The VARIO units are of modular construction in order to meet different requirements,
More informationAgilent Dry Scroll Pumps. 2-3 Features and Benefits 4-5 Typical Applications 6-22 Pump Models Scroll Accessories
Agilent Dry Scroll Pumps 2-3 Features and Benefits 4-5 Typical Applications 6-22 Pump Models 23-29 Scroll Accessories Scroll Pumps Features and Benefits Agilent dry scroll pumps create vacuum using a dual
More informationE and DK - Pumps. Rotary Piston Pumps E 250, DK 200. Operating Instructions GA /6.02. Cat. No
Vacuum Solutions Application Support Service LEYBOLD VACUUM GA 02.200/6.02 E and DK - Pumps Rotary Piston Pumps E 250, DK 200 Cat. No. 105 36 111 16 895 08 895 09 895 10 Operating Instructions Contents
More informationTurbomolecular Pumps TURBOVAC SL The New Premium Line
Turbomolecular Pumps TURBOVAC SL The New Premium Line. 175.60.02 High Vacuum. Experience, Performance, Innovation. Oerlikon Leybold Vacuum has been a world leader in vacuum technology for over 150 years,
More informationSIHI LPH-X - Liquid Ring Vacuum Pump Two Stage
- Liquid Ring Vacuum Pump Two Stage 45008, 45311, 45316 Pressure Range: Suction Volume: 33 to 1013 mbar 55 to 258 m³/h CONSTRUCTION Sterling SIHI liquid ring vacuum pumps have a simple but robust construction
More informationLiquid ring vacuum pumps
Liquid ring vacuum pumps LEH 350, LEH 450 Pressure range: Suction volume flow: 33 to 1013 mbar 120 to 535 m³/h CONSTRUCTION TYPE SIHI liquid ring vacuum pumps are displacement pumps of uncomplicated and
More informationSIHI LPH-X - Liquid Ring Vacuum Pump Two Stage
- Liquid Ring Vacuum Pump Two Stage LPH 45008, LPH 45311, LPH 45316 Pressure Range: Suction Volume: 33 to 1013 mbar 55 to 258 m³/h CONSTRUCTION Sterling SIHI liquid ring vacuum pumps have a simple but
More informationRUVAC WSIWSU 251/501/1001/2001
Vacuum Solutions Application Support Service LEYBOLD VACUUM GA 03.108/14.02 RUVAC WSIWSU 251/501/1001/2001 Roots pump with mineral oil, synthetic oil or PFPE filling Cat.No. 101 83 117 22/32/42/52 117
More informationOPERATING INSTRUCTIONS GA01300_0902
OPERATING INSTRUCTIONS GA01300_0902 TRIVAC B D 16 BCS / D 25 BCS Rotary Vane Vacuum Pump with mineral oil with PFPE Part Nos. 113 68/69 113 70/72/78/79 113 80/82 154 50/51 vacuum Contents Section Page
More informationA E R Z E N S C R E W C O M P R E S S O R S
A E R Z E N S C R E W C O M P R E S S O R S AERZEN - DELTA TWIN - Two Stage Screw Compressors Oil free compressed air technology A E R Z E N E R M A S C H I N E N F A B R I K G M B H V1-016 01 EN 2000
More informationMechanical Booster Pump PRC-A Series, PMB-B, C (M) Series
(Mechanical Booster Pump) Components Division, ULVAC, Inc. Mechanical Booster Pump PRC-A Series, PMB-B, C (M) Series Booster pumps can be used with roughing pumps, such as oil rotary pumps, dry vacuum
More informationSogevac SV630 B - SV750 B
Sogevac SV630 B - SV750 B Single-stage, oil-sealed rotary vane pump Operating instructions GA02319_002_03 Part Numbers : 960 862 960 863 960 865 960 866 960 867 960 869 960 875 Contents Page Important
More informationTRIVAC B D 40 B / D 65 B Rotary Vane Vacuum Pump ATEX Categories 3 i and 3 i/o with mineral oil
TRIVAC B D 40 B / D 65 B Rotary Vane Vacuum Pump ATEX Categories 3 i and 3 i/o with mineral oil Operating Instructions GA01218_002_A2 Part Nos. 11286 3i 11296 3i 140180 3i/3o 140190 3i/3o 170046 170284
More informationHENALINE. A complete line of single-stage rotary vane pumps for low and medium vacuum applications. Safe. Reliable. Powerful.
HENALINE A complete line of single-stage rotary vane pumps for low and medium vacuum applications. Safe. Reliable. Powerful. HENALINE A complete line of single-stage rotary vane pumps for low and medium
More informationnxds DRY SCROLL PUMP THE ULTIMATE DRY CHOICE
nxds DRY SCROLL PUMP THE ULTIMATE DRY CHOICE With exceptional pumping capability, ultimate vacuum performance and state-of-the-art design features, the nxds dry scroll pump is the best performing pump
More informationTRIVAC B. Rotary Vane Vacuum Pump S/D 4 / 8 B. Operating Instructions GA /8.02. Cat. No /46/55/56
Vacuum Pumps Instrumentation Fittings and Valves LEYBOLD VACUUM GA 01.201/8.02 TRIVAC B Rotary Vane Vacuum Pump S/D 4 / 8 B Cat. No. 102 45/46/55/56 103 01/02/03/04/05/06/07 103 11/12/13/14/15/16/17 112
More informationAPOVAC R Vacuum Systems
APVAC R Vacuum Systems with closed ring-liquid loop for the suction and recovery of gases and vapours APVAC = Anti Pllution VACuum PED APVAC R APVAC Vacuum systems with closed ring-liquid loop for the
More informationThe K Series: compact, cost efficient, consistently oil free. Construction advantages.
The K Series: compact, cost efficient, consistently oil free. Construction advantages. UNIQUE: THE PUSH ROD PRINCIPLE. The K series is engineered to provide a cost effective source oil free com-pressed
More informationVacuum Valves. Manually Operated Electropneumatically Operated Electromagnetically Operated Special Valves Gate Valves
Vacuum Valves Manually Operated Electropneumatically Operated Electromagnetically Operated Special Valves Gate Valves 176.01.02 Excerpt from the Product Section C14 Edition July 2007 Contents General The
More informationSIHI LPH-X - Liquid Ring Vacuum Pump One Stage
- Liquid Ring Vacuum Pump One Stage LPH 40106, LPH 40411, LPH 40516 Pressure Range: Suction Range: 150 to 1013 mbar 50 to 270 m³/h CONSTRUCTION Sterling SIHI liquid ring vacuum pumps have a simple but
More informationTwo Stage Rotary Vane Vacuum Pumps Operation and Maintenance Manual
Two Stage Rotary Vane Vacuum Pumps Operation and Maintenance Manual Model 100 3.5 100 l/min. 3.5 CFM 6 m 3 /hr. Model 200 7 200 l/min. 7 CFM 12 m 3 /hr. Model 400 14 400 l/min. 14 CFM 24 m 3 /hr. Model
More informationA E R Z E N S C R E W C O M P R E S S O R S
A E R Z E N S C R E W C O M P R E S S O R S New Aerzen Screw Compressor Units Delta Screw Generation 5 Intake volume flows from 270 m³/h up to 2.600 m³/h A E R Z E N E R M A S C H I N E N F A B R I K G
More informationTRIVAC B. Rotary Vane Vacuum Pump S 40 B, D 40 B, S 65 B, D 65 B. Operating Instructions GA /8.02
Vacuum Pumps Instrumentation Fittings and Valves LEYBOLD VACUUM GA 01.203/8.02 TRIVAC B Rotary Vane Vacuum Pump S 40 B, D 40 B, S 65 B, D 65 B Cat. No. 102 86/96 103 45/46/47/55/56/57 112 86/96 113 45/46/47/55/56/57
More informationDRY PUMPS AND SYSTEMS FOR HAZARDOUS APPLICATIONS
DRY PUMPS AND SYSTEMS FOR HAZARDOUS APPLICATIONS MORE THAN PUMPS, COMPLETE VACUUM SOLUTIONS CXS Chemical Dry Pumps 233 CDX Dry Vacuum Pumps 239 EDP Chemical Dry Pumps 244 Shop online at shop.edwardsvacuum.com
More information5 Compact Vacuum Systems. Compact Vacuum Systems
Compact Vacuum Systems Compact Vacuum Systems 7 Compact Vacuum Systems DC 11-Module The DC 11-Module is a complete central unit for source extraction and industrial cleaning. The unit can manage just about
More informationTRIVAC B LEYBOLD VACUUM. Rotary Vane Vacuum Pump S/D 16, 25 B. Operating Instructions GA /9.02. Cat.-No /66/75/76
Vacuum Pumps Instrumentation Fittings and Valves LEYBOLD VACUUM GA 01.202/9.02 TRIVAC B Rotary Vane Vacuum Pump S/D 16, 25 B Cat.-No. 102 65/66/75/76 103 25/26/27/28/31/32/35/36/37/38/48/49 112 65/66/75/76
More informationVacuum Furnace Pumping Systems
Vacuum Furnace Pumping Systems Failures and Solutions December 4, 2014 Presented By: William R Jones, CEO Solar Atmospheres Inc., www.solaratm.com Technical Contributors: Virginia M Osterman, Ph.D. Senior
More informationPA-S small filter. Technical Data G 1/8
PA-S small filter PA-S small filter G 1/8 Bowl material Polyamid Head material Polypropylene Gasket material Buna-N Filter material PE 5µm, 35µm or 80µm Temperature Min./Max. C 5-50 Maximum pressure bar
More information2-way and 3-way globe valves
2-way and 3-way globe valves Table of Contents Background Project planning 2 Flow characteristics 2 Principles of flow control 3 ydraulic circuits 4 Design and dimensioning Cavitation diagrams 5 Design
More informationGmbH Lufttechnik Dresden USER INFORMATION ROOF FANS SERIES VRV. vertical outlet. Issue 07/02
GmbH Lufttechnik Dresden USER INFORMATION ROOF FANS SERIES VRV vertical outlet Issue 07/02 Roof fans made of plastic materials Series VRV with vertical outlet Usable in ventilation engineering of all branches
More informationPiston Compressors. Volume range: l/min
Piston Compressors Volume range: 235 10900 l/min Intelligence, innovation, reliability variable modular system operationally reliable low speeds long operating life of valves low noise emission robust
More informationTURBOVAC ix Turbomolecular Pumps 90 l/s l/s
TURBOVAC ix Turbomolecular Pumps 90 l/s - 450 l/s 175.62.02 Discover new dimensions With TURBOVAC ix, highest functionality meets outstanding performance. Our ix turbomolecular pump range with integrated
More informationSOGEVAC SV40 B / SV65 B / SV100 B / SV120 B ATEX Cat 2
SOGEVAC SV40 B / SV65 B / SV100 B / SV120 B ATEX Cat 2 Single-stage, oil sealed rotary vane pump. Operating Instructions 130001815_002_C0 II (i) 2G b IIB+H2 T3 / (o) 2G IIC T4 (10 C
More informationCompressed Air Filters
Compressed Air Filters Engineered to Save The New Clean Air Solution The advanced range of CompAir inline equipment has been specially developed to make your compressed air system more energy efficient
More informationSO 61 to SO 126 Oil-free screw compressors (air or water cooled)
LFL 2012-03_EN_olie-vrij_schroef_so-serie SO 61 to SO 126 Oil-free screw compressors (air or water cooled) Free air delivery: 5.25 13.01 m³/min, 185 459 cfm Pressure range: 8 10 bar, 115 150 psig Motor
More informationCompact Vacuum Systems
Compact Vacuum Systems 6 Compact Vacuum Systems DC 11-Module The DC 11-Module is a complete central unit for source extraction and industrial cleaning. The unit can manage just about every kind of dust
More informationSwing Piston Compressors and Vacuum Pumps
Swing Piston Compressors and Vacuum Pumps NPK 018 AC Pressure NPK 018 DC Pressure NPK 018 AC Vacuum NPK 018 DC Vacuum Operating and Installation Instructions Read and observe these Operating and Installation
More informationResolair 64 and 68. Comfort air conditioning unit with highly efficient regenerative heat storage packages. AIR VOLUME FLOW: 3,900 23,100 m³/h
Comfort air conditioning unit with highly efficient regenerative heat storage packages 68 10 01 - simplified illustration Automatically selects the most economical operating mode! 64 and 68 AIR OLUME FLOW:
More informationVapour Pumps. High Throughput Diffusion Pumps 108. Vapour Booster Pumps 114. Vapour Pumps for Scientific Instruments and R&D Applications 118
Vapour Pumps 105 High Throughput Diffusion Pumps 108 Vapour Booster Pumps 114 Vapour Pumps for Scientific Instruments and R&D Applications 118 Diffstak Installation 120 Vapour Pump Spares 122 Vapour Pumps
More informationP a c k a g e s. One step ahead. Energy-efficient Reliable Compact Quiet
One step ahead. elta HYBRID P a c k a g e s Delta Hybrid Volume flows from 110 m3/h to 5800 m3/h (65 to 3,400 cfm) Pressures to 22 psig (1500 mbar) Vacuum to 21" Hg (-700mbar) Energy-efficient Reliable
More informationEurovacuum EVC Series
Eurovacuum EVC Series Dry Running Claw Vacuum Pump Eurovacuum EVC Series Dry Running Claw Vacuum Pumps Eurovacuum Company is offering its various products to meet industrial vacuum needs. Eurovacuum Company
More informationVolumeter TRZ 03-K PRODUCT INFORMATION. Reliable Measurements of Gas
Volumeter TRZ 0-K PRODUCT INFORMATION Reliable Measurements of Gas Method of operation, Construction Method of operation The TRZ 0-K Volumeter is a flow meter suitable for metering gases, where the rate
More informationR Oil-sealed, rotary vane vacuum pumps
Oil-sealed, rotary vane vacuum pumps R 5 0004-1600 R 5 Series Vacuum Pumps Description Modular designed Busch R 5 oil sealed rotary vane vacuum pumps are single stage, aircooled, and direct driven. This
More informationLiquid ring vacuum pumps in compact design
Liquid ring vacuum pumps in compact design LEM 90, LEM 125, LEM 150 LEL 90, LEL 125, LEL 150 Pressure range: Suction volume flow: 33 to 1013 mbar 32 to 170 m³/h CONSTRUCTION TYPE SIHI liquid ring vacuum
More informationSULLAIR Single-stage Rotary Screw Air Compressors
SULLAIR Single-stage Rotary Screw Air Compressors Constant Speed and Variable Speed Drives 149 261 kw 200 350 hp About Sullair For more than 50 years, Sullair has been on the leading edge of compressed
More informationCOMPACT DRY PUMPING SYSTEMS DRYTEL SERIES
COMPACT DRY PUMPING SYSTEMS DRYTEL SERIES COMPACT DRY PUMPING SYSTEMS DRYTEL SERIES Dry pumping units The Drytel series of products are dry pumping systems that include an Adixen molecular drag pump (MDP)
More informationLiquid ring compressors
Liquid ring compressors KPH 65212, KPH 65218 Compression pressures: Suction volume flow: 2 to 7 bar 375 to 660 m³/h CONSTRUCTION TYPE Sterling SIHI liquid ring compressors are displacement compressors
More informationSULLAIR Single-stage Rotary Screw Air Compressors
SULLAIR Single-stage Rotary Screw Air Compressors Constant Speed and Variable Speed Drives 93 261 kw 125 350 hp About Sullair For more than 50 years, Sullair has been on the leading edge of compressed
More information[Small diaphragm vacuum pumps]
[Small diaphragm vacuum ] The small vacuum shown on this page produce vacuum using a diaphragm. They can be used either as vacuum pump or as a small compressor, and they are able to deliver 100% oil-free
More informationOil Sealed Packages Liquid Ring Vacuum Pumps and Compressors
Oil Sealed Packages Liquid Ring Vacuum Pumps and Compressors NASH Oil Sealed Packages Versatile Design Each self-contained system is complete with all of the components for your basic operating needs.
More informationSwing Piston Compressors and Vacuum Pumps
Swing Piston Compressors and Vacuum Pumps NPK 050 NPK 0100 Operating and Installation Instructions Read and observe these Operating and Installation Instructions! KNF Neuberger GmbH Alter Weg 3 D-79112
More informationPressure degassing systems
Pressure degassing systems A degassing system consists of several components: Degassing unit Feedwater tank Instrumentation and control technology Steel structures, platforms and ladders Exhaust vapours
More informationOperating Instructions
Translation of the original instructions ONF 16 S / ONF 25 S Oil Mist Filter Operating Instructions PD 0057 BEN/C (1301) EN Table of contents Table of contents 1 About this manual...............................................
More informationProducts for Vacuum and Pressure
The nnovation leader Products for Vacuum and Pressure Blower & Vacuum Pump Range 160 to 30,500 m 3 /hr Pressure to 1030 mbar G Vacuum to 540 mbar G 216 to 1,190 m 3 /hr Vacuum to 540 mbar A Multi Stage
More informationRoots Packaged Blower Units
Roots Packaged Blower Units Standard Blower and Exhaus SRB blower units and SRE exhauster units Each standard packaged blower or exhauster combines a Roots blower unit supplying oil-free air with an electric
More informationSullair: An Industry Leader
Sullair: An Industry Leader SULLAIR LEADERSHIP Since 1965, Sullair has been recognized worldwide as an innovator and leader in rotary screw compression and vacuum technology. Sullair designs and manufactures
More informationEurovacuum EVC Series. Dry Running Claw Vacuum Pump
Eurovacuum EVC Series Dry Running Claw Vacuum Pump Eurovacuum EVC Series Dry Running Claw Vacuum Pumps Eurovacuum Company is offering its various products to meet industrial vacuum needs. Eurovacuum Company
More informationSCREW COMPRESSORS OIL-FREE
SCREW COMPRESSORS OIL-FREE Over 100,000 compressed air users expect more when it comes to their compressed air supply. BOGE air provides them with the air to work. BOGE oil-free screw compressors have
More informationJUMO dtrans p20. Process pressure transmitter. Type Brief description. Key features. Block diagram
Data Sheet 403025 Page 1/10 JUMO dtrans p20 Process pressure transmitter Brief description The JUMO dtrans p20 pressure transmitter with HART interface combines maximum precision with easy operation. It
More informationPOSITIVE DISPLACEMENT BLOWERS. for conveyance and compression of process gases
AERZEN POSITIVE DISPLACEMENT BLOWERS for conveyance and compression of process gases Series GR, sizes 12 to 21 intake volume flows from 100 m 3 /h up to 50.000 m 3 /h Series GQ, sizes 17 to 22 intake volume
More informationULTIMA U75 U HP OIL-FREE TWO-STAGE VARIABLE SPEED ROTARY SCREW COMPRESSOR. Ultima
ULTIMA U75 U160 100 200 HP OIL-FREE TWO-STAGE VARIABLE SPEED ROTARY SCREW COMPRESSOR Ultima GARDNER DENVER ULTIMA What makes the ULTIMATE oil-free compressor? Is it highest efficiency? Is it lowest noise
More informationKSI Filtertechnik GmbH Siemensring D Willich Tel Fax
BA SIC.LINE Rev 1.0.1 Page 1 of 9 KSI Filtertechnik GmbH Siemensring 54-56 D-47877 Willich Tel. +49 21 54 89 108-0 Fax +49 21 54 89108-282 www.ksi.eu mail@ksi.eu ECOCLEAN Compressed air filters new generation
More informationWORKSTATION PICTURE SHOWS PRODUCT WITH OPTIONS
WORKSTATION PICTURE SHOWS PRODUCT WITH OPTIONS Ready to operate workstation, incl. main antechamber and vacuum pump Different glovebox sizes available PLC controlled with Siemens color touch panel Automatic
More informationMODEL INFORMATION CANNED MOTOR PUMP TYPE CAM HERMETIC
MODEL INFORMATION CANNED MOTOR PUMP TYPE CAM HERMETIC ... 3... 4 3000 rpm 50 Hz / 3600 rpm 60 Hz... 4... 5... 7 Modular pump / motor systems... 7 Materials...........................................................
More information