CERAMIC CAPACITOR PART NUMBER EXPLANATION... 1 CLASS I 50V,100V,500V,1KV,2KV,3KV,6KV TEMPERATURE COMPENSATION TYPE

Transcription

1 Table of Contents Subject Page CERAMIC CAPACITOR PART NUMBER EXPLANATION CLASS I 50V,100V,500V,1KV,2KV,3KV,6KV TEMPERATURE COMPENSATION TYPE CLASS II 50V,100V,500V,1KV,2KV,3KV HI-K TYPE CLASS III SEMI-CONDUCTIVE TYPE KV,2KV,3KV,LOW DISSIPATION LB,LR,TYPE SAFETY STANDARD CERAMIC CAPACITOR PART NUMBER EXPLANATION AH TYPE-CLASS X1/Y1,AC TYPE-CLASS X1/Y AH/AC TYPE DETAIL SPECIFICATION SAFETY STANDARD CERAMIC CAPACITOR APPROVAL FILE NUMBER,TAPING SPECIFICATION AND DIMENSION RADIAL/AXIAL LEADED MULTILAYER CERAMIC CAPACITOR PART NUMBER EXPLANATION RADIAL LEADED CAPACITOR FEATURES DIMENSION AND CAPACITANCE CHART RADIAL LEADED CAPACITOR TAPING SPECIFICATION&PACKING QUANTITY

2 SAP Part Number Explanation To order, please also specify Pan Overseas Part No. as the following example for SAP system : YP K 040 B 20 C 7 B Dielectric Voltage Capacitance Tolerance Diameter Lead Style Length or Packing Length Tolerance ➊ ➋ ➌ ➍ ➎ ➏ ➐ ➑ ➒ ➓ Pitch Coating ➊ Dielectric ➋ Voltage ➌ Capacitance ➍ Tolerance Class I : CODE WV CODE Capacitance CODE Capacitance CODE T.C.(ppm/ C) VDC 0R5 0.5 PF C ± 0.25 PF(for 2~5)pF CH CH (0±60) VDC PF D ± 0.5 PF(for 6~10)pF SL SL (+350 ~ -1000) VDC PF J ± 5% Class II : VDC PF K ± 10% CODE T.C( C%) 102 1K VDC uf M ± 20% YP Y5P(±10%) 202 2K VDC uf Z -20 ~ +80% XR X7R(±15%) 302 3K VDC ZU Z5U(+22 ~ -56%) 602 6K VDC YU Y5U(+20 ~ -55%) ZV Z5V(+22 ~ -82%) YV Y5V(+22 ~ -82%) Class III : ➎ Diameter ➏ Lead Style - Reference Lead Style ➐ Packing / Pitch / Lead Length CODE T.C( C%) CODE Diameter max Taping (ex) FY Y5V(+22 ~ -82%) 040 CODE Packing & Pitch Low DF : 050 AF Box & Pitch 15.0 mm CODE D.F. T.C( C%) 060 AN Box & Pitch 12.7 mm LR 0.2% Y5R(+15 ~ -30%) 070 AM Box & Pitch 25.4 mm LB 0.5% Y5P(±10%) Refer to the product diameter D max 3E Bulk (ex) Length 3.5 mm mm 120 4E 4.5 mm mm mm ➑ Length Tolerance ➒ Pitch ➓ Coating Type CODE Length Tolerance CODE Lead Spacing CODE Coating A ± 0.5 mm(only for short kink lead type) ± 0.8mm P Phenolic Resin-Pb free Rated, Voltage 1KV B ± 1.0 mm ± 0.8mm (for Bulk) A Phenolic resin-haloge free and Pb free Rated,Voltage 1KV / -0.2 mm (for taping) C Min ± 1mm B Epoxy Resin-Pb Free Rated, Voltage 2KV D Taping & Special Purpose ± 1mm H Epoxy Resin-Halogen free Rated and Pb Free,Voltage 2KV 21

3 Class I 50V,100V,500V,1KV,2KV,3KV,6KV, Temperature Compensation Type Features : Capacitance has linear temperature coefficient Capacitance high stability Epoxy Coating for 2KV, 3KV,6KV parts (equivalent to UL94V-0 standards). RoHS Compliance Halogen free products are available Low loss at wide range of frequency General specification: Capacitance Range Capacitance Tolerance Operating Temperature Range Rated Voltage 1pF to 820pF ±0.25pF(for 2~5pF), ±0.5pF(for 6~10pF), ±5%(for 12~820pF) Rated Voltage 2KV:-25 C~+125 C ; Rated Voltage 3KV:-25 C+125 C 50,100,500,1000,2000, 3000, 6000 VDC Q 1MHz, 1±0.2 Vrms, 25 C C 30 pf...q 1,000, C<30 pf...q *C Insulation Resistance 25 C Dielectric Strength Testing Parameters 10,000MΩ minimum 50~500VDC:3 times the rated WVDC ; 1K,2K,3KVDC:2 times the rated WVDC; 6KVDC:1.5 times the rated WVDC. 1KHz ±20%, 1.0Vrms±0.2Vrms Lead style : Lead type Lead Lead Configuration Lead type Lead Lead Configuration Lead style:b Lead style:h Type 1 Straight long lead B Type 4 Inside kink lead H Lead style:x Lead style:d Type 2 Outside kink lead X Type 5 Vertical kink short lead D Lead style:l Lead style:m Type 3 Straight short lead L Type 6 Double outside kink lead M 2

4 Class I 50V,100V,500V,1KV,2KV,3KV,6KV, Temperature Compensation Photo: Manufacturing products range Cap. Value VS. Rated voltage, Product diameter & Type T.C. CH (Class I, Temperature:-25 C~+85 C, T.C.C.: 0±60ppm/ C) Rated voltage 50V(CH500)&100V(CH101) 500V(CH501) 1KV(CH102) 2KV(CH202) D Ø () D max. (mm) T max. (mm) R Packing T or B B T or B T or B T or B Coating Phenolic Resin Epoxy Resin 1. Temperature characteristic 2. Nominal Capacitance 3. Capacitance tolerance 4. Rated voltage 5. Manufacturer s identification Marking CH : No marking, but recognized by black color presented on the top of product. Identified by 3-figure code. 5pF 5 100pF 101 C:±0.25pF D:±0.5pF J:±5% 50/100V Marked as underline 500V No marking (is blank) 1000V Marked 1KV 2000V Marked 2KV Shall be marked as UK, but D Ø =6.0 mm and less in Dia shall be omitted. P.S.:Packing : T Packing in taping type. B Packing in bulk type. 3

5 Class I 50V,100V,500V,1KV,2KV,3KV,6KV, Temperature Compensation Type Photo: Manufacturing product range Cap. Value VS. Rated voltage, Product diameter & Type T.C. SL (Class I, Temperature:+20 C~+85 C, T.C.C.: +350 ~ -1000ppm/ C) Rated voltage 50V(SL500);100V(SL101) 500V(SL501) 1KV(SL102) 2KV(SL202) D Ø () D max. (mm) T max. (mm) Packing T or B T or B T or B T or B B coating Phenolic Resin Epoxy Resin 1. Temperature characteristic 2. Nominal Capacitance 3. Capacitance tolerance 4. Rated voltage 5. Manufacturer s identification Marking SL:No marking. Identified by 3-figure code. 5pF 5 100pF 101 C:±0.25pF D:±0.5pF J:±5% 50/100V Marked as underline 500V 1000V 2000V No marking (is blank) Marked 1KV Marked 2KV Shall be marked as UK, but D Ø =6.0 mm and less in Dia shall be omitted. 4

6 Class I 50V,100V,500V,1KV,2KV,3KV,6KV, Temperature Compensation Type Photo: CH SL Manufacturing product range Cap. Value VS. Rated voltage, Product diameter & Type T.C. CH (Class I, Temperature:-25 C~+85 C, T.C.C.:0±60ppm/ C) SL (Class I, Temperature:+20 C~+85 C, T.C.C.: +350 ~ -1000ppm/ C) Rated voltage 3KV(CH302) 3KV(SL302) Ø (mm) D max. (mm) T max. (mm) ød (mm) 0.6 ± 0.06 Packing BULK Coating Epoxy Resin 1. Temperature characteristic 2. Nominal capacitance 3. Capacitance tolerance 4. Rated voltage 5. Manufacturer's identification 6. Halogen and Pb free CH: Be marked CH SL: No marking 1. Cap. 100pF Ex.120pF Cap<100pF Ex. 22pF 22 C: ±0.25pF D: ±0.5pF J: ±5% 3000V : Be marked 3KV Shall be marked as, but when the body diameter 060 shall be omitted. When the epoxy resin is Halogn and Pb free, there is a _ marking. Definition of date code marking : 7.Supplier of Epoxy 8.No. of test equipment 9.Factory of manufacture 10.Year of manufacture 11.Month of manufacture 12.Week of manufacture by month Remark: K40- K100- K130- K300-5

7 Class I 50V,100V,500V,1KV,2KV,3KV,6KV, Temperature Compensation Type Photo: CH SL Manufacturing product range Cap. Value VS. Rated voltage, Product diameter &Type T.C. CH (Class I, Temperature:-25 C~+85 C, T.C.C.:0±60ppm/ C) SL (Class I, Temperature:-25 C~+85 C, T.C.C.: +350 ~ -1000ppm/ C) Rated voltage 6KV 6KV Ø (mm) D max. (mm) T max. (mm) ød (mm) 0.6 +/ Temperature characteristic 2. Nominal capacitance 3. Capacitance tolerance 4. Rated voltage 5. Manufacturer's identification 6. Halogen and Pb free CH: Be marked CH SL: No marking 1. Cap. 100pF Ex.120pF Cap<100pF Ex. 22pF 22 C: ±0.25pF D: ±0.5pF J: ±5% 6000V : Be marked 6KV Shall be marked as, but when the body diameter 060 shall be omitted. When the epoxy resin is Halogn and Pb free, there is a _ marking. Definition of date code marking : 7.Supplier of Epoxy 8.No. of test equipment 9.Factory of manufacture 10.Year of manufacture 11.Month of manufacture 12.Week of manufacture by month Remark: K40- K100- K130- K300-6

8 Class II 50V,100V,500V,1KV,2KV,3KV, Hi-K Type Features : Capacitance has non-linear temperature coefficient. Large capacitance in small size. Epoxy Coating for 2KV and 3KV parts (equivalent to UL94V-0 standards). RoHS Compliance Halogen free products are available Wide range of general purposes applications. General specification: Capacitance Range Capacitance Tolerance Operating Temperature Range Rated Voltage 100pF to 22000pF ±10%(for Y5P&X7R), ±20%(for Z5U), +80% -20%(for Z5V&Y5V) -25 C~ 85 C(Y5P,Y5V) ; 10 C~ 85 C(Z5U, Z5V) ; -55 C~ 125 C(X7R) 50,100,500,1000,2000,3000 VDC Dissipation Factor (tan δ) Y5P, Z5U, X7R : tan δ 2.5% Z5V, Y5V : tan δ 5.0% Insulation Resistance 25 C Dielectric Strength Testing Parameters 10,000MΩ minimum or 200MΩ µf whichever is smaller 50~500VDC: 2.5 times the rated WVDC; 1K,2K,3KVDC: 2 times the rated WVDC 1KHz ±20%, 1.0Vrms±0.2Vrms Lead style : Lead type Lead Lead Configuration Lead type Lead Lead Configuration Lead style:b Lead style:h Type 1 Straight long lead B Type 4 Inside kink lead H Lead style:x Lead style:d Type 2 Outside kink lead X Type 5 Vertical kink short lead D Lead style:l Lead style:m Type 3 Straight short lead L Type 6 Double outside kink lead M 7

9 Class II 50V,100V,500V,1KV,2KV,3KV, Hi-K Type Photo: Manufacturing product range Cap. Value VS. Rated voltage, Product diameter & Type T.C. Y5P (Class II, Temperature:-25 C~+85 C, T.C.C.:±10%) Rated voltage 50V(YP500)&100V(YP101) 500V(YP501) 1KV(YP102) 2KV(YP202) D Ø () D max. (mm) T max. (mm) Packing T or B B T or B B T or B B T or B B Coating Phenolic Resin Epoxy Resin 1. Temperature characteristic 2. Nominal Capacitance 3. Capacitance tolerance 4. Rated voltage 5. Manufacturer s identification Marking 1. be marked B 2. when D ø =4.0 mm or rated voltage 1KV & D ø =5.0, the B shall be omitted. P.S.:Packing : T Packing in taping type. Identified by 3-figure code. 1000pF pF 332 K: ±10% B Packing in bulk type. 50/100V 500V 1000V 2000V Marked as underline No marking (is blank.) Marked 1KV Marked 2KV Shall be marked as UK, but D Ø =6.0 mm and less in Dia shall be omitted. 8

10 Class II 50V,100V,500V,1KV,2KV,3KV, Hi-K Type Photo: Manufacturing product range Cap. Value VS. Rated voltage, Product diameter & Type T.C. Z5U (Class II, Temperature:+10 C~+85 C, T.C.C.:+22~ -56%) Rated voltage 50V(ZU500)&100V(ZU101) 500V(ZU501) 1KV(ZU102) 2KV(ZU202) D Ø () D max. (mm) T max. (mm) Packing T or B T or B T or B B T or B B Coating Phenolic Resin Epoxy Resin 1. Temperature characteristic 2. Nominal Capacitance 3. Capacitance tolerance 4. Rated voltage 5. Manufacturer s identification Marking 1. be marked E 2. when D ø =4.0 mm or rated voltage 1KV & D ø =5.0, the E shall be omitted. Identified by 3-figure code. 4700pF pF 103 M: ±20% 50/100V 500V 1000V 2000V Marked as underline No marking (is blank.) Marked 1KV Marked 2KV Shall be marked as UK, but D Ø =6.0 mm and less in Dia shall be omitted. P.S.:Packing : T Packing in taping type. B Packing in bulk type. 9

11 Class II 50V,100V,500V,1KV,2KV,3KV, Hi-K Type Photo: Manufacturing product range Cap. Value VS. Rated voltage, Product diameter & Type T.C. Z5V (Class II, Temperature:+10 C~+85 C, T.C.C.:+22~ -82%) Rated voltage 50V(ZV500)&100V(ZV101) 500V(ZV501) 1KV(ZV102) 2KV(ZV202) D Ø () D max. (mm) T max. (mm) Packing T or B T or B T or B T or B T or B T or B T or B T or B B Coating Phenolic Resin Epoxy Resin 1. Temperature characteristic 2. Nominal Capacitance 3. Capacitance tolerance 4. Rated voltage 5. Manufacturer s identification Marking Z5V: the logo is F, but the F shall be omitted. Identified by 3-figure code. 4700pF pF 103 Z: -20~+80% 50/100V 500V 1000V 2000V Marked as underline No marking (is blank.) Marked 1KV Marked 2KV Shall be marked as UK, but D Ø =6.0 mm and less in Dia shall be omitted. P.S.:Packing : T Packing in taping type. B Packing in bulk type. 10

12 Class II 50V,100V,500V,1KV,2KV,3KV, Hi-K Type Manufacturing product range Cap. Value VS. Rated voltage, Product diameter & Type Photo: T.C. Rated voltage D Ø (CODE) D max. (mm) T max. (mm) X7R (Class II, Temperature:-55 C~+125 C, T.C.C.:±15%) 50V 500V 1KV 2KV Packing T T B T B T B Coating Phenolic Resin Epoxy Resin Marking 1. Temperature characteristic be marked R P.S.:Packing : T Packing in taping type. 2. Nominal Capacitance Identified by 3-figure code. 1000pF pF Capacitance tolerance K: ±10% B Packing in bulk type. 4. Rated voltage 50/100V 500V 1000V 2000V Marked as underline No marking (is blank.) Marked 1KV Marked 2KV 5. Manufacturer s identification Shall be marked as UK, but D Ø =6.0 mm and less in Dia shall be omitted. 11

13 Class II 50V,100V,500V,1KV,2KV,3KV, Hi-K Type Photo: Y5P Z5U Manufacturing product range Cap. Value VS. Rated voltage, Product diameter & Type T.C. Y5P (Class II, Temperature:-25 C~+85 C, T.C.C.:±10%) Z5U (Class II, Temperature:+10 C~+85 C, T.C.C.:+22~ -56%) Rated voltage 3KV (YP302) 3KV (ZU302) D Ø D max. (mm) T max. (mm) Ø d (mm) 0.6 ± 0.06 Packing B Coating Epoxy Resin 1. Temperature characteristic 2. Nominal capacitance 3. Capacitance tolerance 4. Rated voltage 5. Manufacturer's identification 6. Halogen and Pb free Y5P: Be marked B Z5U: Be marked E Definition of date code marking : 7.Supplier of Epoxy Identified by 3-figure code when Cap. 100pF Ex. 1000pF No. of test equipment P.S.:Packing : T Packing in taping type. K: ±10% (For Y5P) M: ±20% (For Z5U) 9.Factory of manufacture B Pack in bulk type. 3000V : Be marked 3kV 10.Year of manufacture Shall be marked as, but when the body diameter 060 shall be omitted. 11.Month of manufacture When the epoxy resin is Halogn and Pb free, there is a _ marking. 12.Week of manufacture by month 12

14 Class II 50V,100V,500V,1KV,2KV,3KV, Hi-K Type Manufacturing product range Cap. Value VS. Rated voltage, Product diameter & Type T.C. Y5V (Class II, Temperature: -25 C~ +85 C, T.C.C.:+22% ~ -82%) Rated voltage 50V 100V 500V 1KV 2KV D Ø D max. (mm) T max. (mm) Packing T or B T or B T or B T or B B Coating PHENOL EPOXY 1. Temperature Characteristic 2. Nominal Capacitance 3. Capacitance tolerance 4. Rated voltage 5. Manufacturer s identification 50V/100V Marked as underline Marking Y5V: the product logo is F, but it is omitted on marking. Identified by 3-figure code. 4700pF pf 103 Z: -20 ~ +80% 500V 1000V No marking (is blank.) Marked 1KV Shall be marked as UK, but D Ø =6.0 mm and less in Dia shall be omitted. 2000V Marked 2KV P.S.:Packing : T Packing in taping type. B Packing in bulk type. 13

15 Class III Semi-Conductive Type Features : Large capacitance in small size. Low loss at wide range of frequency. Cost saving by replacing film capacitors. Capacitance has linear temperature coefficient. Stable capacitance change over specified temperature range. RoHS Compliance Halogen free products are available Ød DR L General specification: Capacitance Range 22000pF to pF Capacitance Tolerance ±20%, +80%-20% Operating Temperature Range -25 C ~ 85 C Rated Voltage 16,25&50 VDC Dissipation Factor (tan δ) 16V... tan δ 7.5% 25/50V... tan δ 5.0% Insulation Resistance 25 C 16V...100MΩ Minimum or 10MΩ µf 25/50V MΩ Minimum or 20MΩ µf Dielectric Strength Testing Parameters 2 times the rated WVDC 1KHz ±20%, 0.1Vrms Maximum Specification : Manufacturing Product Range T.C. FY (Y5V) Class III Rated voltage 16V 25V 50V D Ø D max. (mm) T max. (mm) Temperature Characteristic 2. Nominal Capacitance 3. Capacitance tolerance 4. Rated voltage 5. Manufacturer s identification Marking Y5V: the product logo is F, but it is omitted on marking. Identified by 3-figure code. 4700pF pf 103 M: ±20% Z: -20~+80% 16V&25V 50V Marked With code: 16V 16V 25V 25V Shall be Marked _ under the rated copacitance. Shall be marked as UK, but D Ø =6.0 mm and less in Dia shall be omitted. 14

16 1KV, 2KV, 3KV Low Dissipation LB,LR Type Features : Reduced heat dissipation permitted due to small dielectric loss of the ceramic material. Operating temperature range is guaranteed up to 125 degree C. Coated with flame-retardant epoxy resin (equivalent to UL94V-0 standards). RoHS Compliance Halogen free products are available Ideal for use on high frequency pulse circuits such as a horizontal resonance circuit for CTV and snubber circuits for switching power supplies.. General specification: Capacitance Range 100pF to 4700pF Capacitance Tolerance ±10%, Operating Temperature Range -25 C ~ 125 C Rated Voltage Dissipation Factor (tan δ) Insulation Resistance 25 C Dielectric Strength Testing Parameters 1K,2K,3K VDC LB: tan δ 0.5% ; LR: tan δ 0.2% 10000MΩ Minimum or 200MΩ µf whichever is smaller (500VDC,60sec) 2 times the rated WVDC 1KHz ±20%, 1.0Vrms±0.2Vrms Lead style : Lead type Lead Lead Configuration Lead type Lead Lead Configuration Lead style:b Lead style:h Type 1 Straight long lead B Type 4 Inside kink lead H Lead style:x Lead style:d Type 2 Outside kink lead X Type 5 Vertical kink short lead D Lead style:l Lead style:m Type 3 Straight short lead L Type 6 Double outside kink lead M 15

17 1KV, 2KV, 3KV Low Dissipation LB,LR Type LB Series Dimensions in mm Part Number Rated Voltage Cap. in pf Cap. Tol. (%) D Max. T Max. LB K VDC 100 ±10% LB K VDC 150 ±10% LB K VDC 180 ±10% LB K VDC 220 ±10% LB K VDC 270 ±10% LB K VDC 330 ±10% LB K VDC 390 ±10% LB K VDC 470 ±10% LB K VDC 560 ±10% LB K VDC 680 ±10% LB K VDC 820 ±10% LB K VDC 1000 ±10% LB K VDC 1500 ±10% LB K VDC 1800 ±10% LB K VDC 2200 ±10% LB K VDC 3300 ±10% LB K VDC 3900 ±10% LB K VDC 4700 ±10% LB K VDC 100 ±10% LB K VDC 150 ±10% LB K VDC 220 ±10% LB K VDC 270 ±10% LB K VDC 330 ±10% LB K VDC 390 ±10% LB K VDC 470 ±10% LB K VDC 560 ±10% LB K VDC 680 ±10% LB K VDC 820 ±10% LB K VDC 1000 ±10% LB K VDC 1200 ±10% LB K VDC 1500 ±10% LB K VDC 1800 ±10% LB K VDC 2200 ±10% LB K VDC 2700 ±10% LB K VDC 3300 ±10% LB K VDC 3900 ±10% LB K VDC 4700 ±10% LB K VDC 100 ±10% LB K VDC 150 ±10% LB K VDC 220 ±10% LB K VDC 330 ±10% LB K VDC 390 ±10% LB K VDC 470 ±10% LB K VDC 560 ±10% LB K VDC 680 ±10% LB K VDC 820 ±10% LB K VDC 1000 ±10% LB K VDC 1500 ±10% LB K VDC 2200 ±10% LB K VDC 2700 ±10% LB K VDC 3300 ±10% LB K VDC 3900 ±10% LB K VDC 4700 ±10%

18 1KV, 2KV, 3KV Low Dissipation LB,LR Type LR series: Dimensions in mm Part Number Rated Voltage Cap. in pf Cap. Tol. (%) D Max. T Max. LR K VDC 100 ±10% LR K VDC 150 ±10% LR K VDC 220 ±10% LR K VDC 270 ±10% LR K VDC 330 ±10% LR K VDC 390 ±10% LR K VDC 470 ±10% LR K VDC 680 ±10% LR K VDC 1000 ±10% LR K VDC 1500 ±10% LR K VDC 2200 ±10% LR K VDC 3300 ±10% LR K VDC 100 ±10% LR K VDC 150 ±10% LR K VDC 220 ±10% LR K VDC 270 ±10% LR K VDC 330 ±10% LR K VDC 390 ±10% LR K VDC 470 ±10% LR K VDC 560 ±10% LR K VDC 680 ±10% LR K VDC 820 ±10% LR K VDC 1000 ±10% LR K VDC 1200 ±10% LR K VDC 1500 ±10% LR K VDC 1800 ±10% LR K VDC 2200 ±10% LR K VDC 3300 ±10% LR K VDC 100 ±10% LR K VDC 150 ±10% LR K VDC 220 ±10% LR K VDC 330 ±10% LR K VDC 390 ±10% LR K VDC 470 ±10% LR K VDC 560 ±10% LR K VDC 680 ±10% LR K VDC 820 ±10% LR K VDC 1000 ±10% LR K VDC 1500 ±10% LR K VDC 2200 ±10%

19 1KV, 2KV, 3KV Low Dissipation LB,LR Type Marking: Temp. Char. LR LB Item Marking (2) (3) L R (1) 471K 1 K V UK (4) (6) (5) (2) (3) LB (1) (4) (6) (5) 102K 2 K V UK (1) Temp. Char. And D.F. Cap.change:-30%~+15%(-25 Cto+125 C) D.F:0.2% Max Cap. change: ±10%(-25 C~85 C) D.F:0.5% Max (2) Nominal Capacitance Identified By 3-Figure. Ex. 100pf 101 A1000 Pf V Marked with code 1KV In case of DC 1000V (3) Rated Voltage 2000V Marked with code 2KV In case of DC 2000V 3000V Marked with code 3KV In case of DC 3000V (4) Capacitance Tolerance K=±10% (5) Manufacturer s Identification Shall Be Marked As UK, But DΦ=6.0 Mm And Less In Dia Shall Be Omitted. (6) Halogen and Pb free When the epoxy resin is Halogen and Pb free,there is a _ marking. 18

20 1KV, 2KV, 3KV Low Dissipation LB,LR Type Caution 1.Caution (Rating) 1-1 Operating Voltage When dc-rated capacitors are to be used in ac or ripple current circuits, be sure to maintain the Vp-p value of the applied voltage or the Vo-p which contains dc bias within the rated voltage range. When the voltage is applied to the circuit, starting or stopping may generate irregular voltage for a transit period because of resonance or switching. Be sure to use a capacitor with a rated voltage range that includes these irregular voltages. When using the low-dissipation (LB, LR Char.) series in a high-frequency and high-voltage circuit, be sure to read the instructions in item 4. Voltage DC Voltage DC + AC Voltage AC Voltage Pulse Voltage (1) Pulse Voltage (2) Positional measurement 1-2 Operating Temperature And Self-Generated Heat Keep the surface temperature of a capacitor below the upper limit of its rated operating temperature range. be sure to take into account the heat generated by the capacitor itself. When the capacitor is used in a high-frequency current, pulse current or similar current, it may self-generate heat due to dielectric loss. The frequency of the applied sine wave voltage should be less than 300kHz. the applied voltage load (*) should be such that the capacitor s self-generated heat is within 20 c at an atmosphere temperature of 25 c. When measuring, use a thermocouple of small thermal capacity-k of ø0.1mm in conditions where the capacitor is not affected by radiant heat from other components or surrounding ambient fluctuations. Excessive heat may lead to deterioration of the capacitor s characteristics and reliability. (Never attempt to perform measurement with the cooling fan running. otherwise, accurate measurement cannot be ensured.) 1-3 Fail-Safe When capacitor is broken, failure may result in a short circuit. Be sure to provide an appropriate fail-safe function like a fuse on your product if failure would follow an electric shock, fire or fume. 1-4 Load Reduction and Self-generated Heat During Application of High-frequency and High-voltage Due to the low self-heating characteristics of low dissipation capacitors, the allowable electric power of these capacitors is generally much higher than that of B characteristic capacitors. However, in case the self heating temperature is 20 C under a high-frequency voltage whose peak-to-peak value equals the capacitor s rated voltage, the capacitor s power consumption may exceed it s allowable electric power. Therefore, when using the Low D.F. series in a high-frequency and high-voltage circuit with a frequency of 1kHz or higher, make sure that the Vp-p values including the DC bias, do not exceed the applied voltage value specified in Table 1. Also make sure that the self-heating temperature (the difference between the capacitor s surface temperature and the capacitor s ambient temperature) at an ambient temperature of 25 C does not exceed the value specified in Table 1. As shown in Fig. 2, the self-heating temperature depends on the ambient temperature. Therefore, if you are not able to set the ambient temperature to approximately 25 C, please contact our sales representatives or product engineers. 19

21 1KV, 2KV, 3KV Low Dissipation LB,LR Type [Table 1] Allowable conditions at high frequency Series DC rated voltage Allowable conditions at High-frequency *3 Bulk Self-heating temp.(25 C ambient temp.) *1 Capacitor s ambient temp. *2 1KV 800Vp-p 1000Vp-p 20 C Max 5 C Max LB LR 2KV 1400Vp-p 2000Vp-p 20 C Max 5 C Max -25 ~ +125 C 3KV 1600Vp-p 3000Vp-p 20 C Max 5 C Max *1 Fig. 1 shows the relationship between the applied voltage and the allowable self-heating temperature regarding 1 to 2KV rated voltage of the low D.F. series LB,LR characteristic. *2 Fig. 2 When the ambient temperature is 85 to 125 C, the applied voltage needs to be further reduced. If the low D.F. series needs o be used at an ambient temperature of 85 to 125 C, please contact our sales representatives or product engineers. *3 Fig. 3 shows reference data on the allowable voltage-frequency characteristic for a sine wave voltage. Failure to follow the above cautions (items 1-1to 1-4) may result, worst case, in a short circuit and cause fuming or partial dispersion when the product is used. Fig 1:Relationship Between Applied Voltage and Self-heating Temperature (Allowable Self-heating Temp. at 25 C Ambient Temp.) 20

22 1KV, 2KV, 3KV Low Dissipation LB,LR Type Fig 2:Dependence of Self-heating Temperature on Ambient Temperature. Fig 3:Allowable Voltage ( Sine Wave Voltage ) Frequency Characteristics (At Ambient Temperature of 85 C or less) 21

23 1KV, 2KV, 3KV Low Dissipation LB,LR Type Because of influence of harmonics, when the applied voltage is a rectangular wave or pulse wave voltage (instead of a sine wave voltage), the heat generated by the capacitor is higher than the value obtained by application of the sine wave with the same fundamental frequency. Roughly calculated for reference, the allowable voltage for a rectangular wave or pulse wave corresponds approximately to the allowable voltage for a sine wave whose fundamental frequency is twice as large as that of the rectangular wave or pulse wave. This allowable voltage, however, varies depending on the voltage and current waveforms. Therefore, you are requested to make sure that the self-heating temperature is not higher than the value specified in Table 1. 2.Caution (Storage And Operating Condition) I. Operating And Storage Environment The insulating coating of capacitors does not form a perfect seal; therefore, do not use or store capacitors in a corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are present. And avoid exposure to Moisture. Before cleaning, bonding or molding this product, verify that these processes do not affect product quality by testing the performance of a cleaned, bonded or molded product in the intended equipment. Store the capacitors where the temperature and relative humidity do not exceed 10 to 40 degrees centigrade and 15 to 85 %. Use capacitors within 6 months. Failure to follow the above cautions may result, worst case, in a short circuit and cause fuming or partial dispersion when the product is used. 3.Caution (Soldering And Mounting) I. Vibration And Impact Do not expose a capacitor or its leads to excessive shock or vibration during use. II. Soldering When soldering this product to a PCB / PWB, do not exceed the solder heat resistance specification of the capacitor. Subjecting this product to excessive heating could melt the internal junction solder and may result in thermal shocks that can crack the ceramic element. When soldering capacitor with a soldering iron, it should be performed in following conditions. Temperature of iron-tip: 400 C Max. Soldering iron wattage: 50W Max. Soldering time: 3.5 sec. Max. Failure to follow the above cautions may result, worst case, in a short circuit and cause fuming or partial dispersion when the product is used. 4. Caution (Handling) Vibration And Impact Do not expose a capacitor or its leads to excessive shock or vibration during use. Failure to follow the above cautions may result, worst case, in a short circuit and cause fuming or partial dispersion when the product is used. Notice 1.Notice (Soldering And Mounting) Cleaning (ultrasonic cleaning) To perform ultrasonic cleaning, observe the following conditions. Rinse bath capacity: output of 20-watts per liter or less. Rinsing time: 5 min. Maximum. Do not vibrate the Pcb/Pwb directly. Excessive ultrasonic cleaning may lead to fatigue destruction of the lead wires. 2.Notice (Rating) Low D.F. series Capacitance might change greatly depending on the surrounding temperature or an applied voltage. So, it is not likely to be suitable for use in a time constant circuit. Please contact us if you need detailed information. 22

24 SAFETY.STANDARD CERAMIC CAPACITOR SAP Part Number Explanation To order, please also specify Pan Overseas Part No. as the following example for SAP system : YV 0AC 472 M 100 L 25 C 7 B ➊ ➋ ➌ ➍ ➎ ➏ ➐ ➑ ➒ ➓ ➊ Temperature characteristic (identified code): CH(NPO) SL YP(Y5P) YU(Y5U) YV(Y5V) Cap. Change (%) 0±60PPM/ C -1000~+350PPM/ C ±10% +20% to -55% +30% to -80% ➋ Type (identified by 3-figure code): 0AC=AC Type(X1/Y2) ; 0AH=AH Type(X1:400V~/Y1:250V); 1AH=AH Type(X1:400V~/Y1:400V) ➌ Capacitance (identified by 3-figure code) ➍ Capacitance tolerance (identified by code) ➎ Nominal body diameter dimension (identified by 3-figure code) ➏ Kinked Lead style Lead type & Lead Configuration Lead type & Lead Configuration Lead type & Lead Configuration Lead style:b Lead style:x Lead style:l Type B straight long lead Type X Outside kink lead Type L Straight short lead Lead style:d Lead style:h Type D Vertical kink short lead Type H Inside kink lead ➐ Packing mode and lead length (identified by 2-figure code) Taping Description Bulk Description (ex) AM Box and Pitch : 25.4 mm (Pitch=10.0mm) 3E lead length L:3.5mm AF Box and Pitch : 15.0 mm (Pitch=7.5mm) 04 lead length L:4.0mm AT Box and Pitch : 30.0 mm (Pitch=7.5mm or 10.0mm) 4E lead length L:4.5mm 20 lead length L:20mm ➑ Length tolerance A B Description ±0.5 mm (only for kink lead type) ±1.0mm ➒ Pitch Description ± 1mm (AC Type) 0 10 ± 1mm (AH Type & AC Type) ➓ Epoxy resin code C MIN. Description D Taping special purpose B H Epoxy Resin Pb free Halogen and Pb free, epoxy resin 23

25 SAFETY STANDARD CERAMIC CAPACITOR AH Type-Class X1/Y1 AC Type-Class X1/Y2 Introduction: These Safety Recognized Ceramic Capacitors are specifically designed for AC applications and meet the safety requirements of various safety standard agencies. They are ideal for across the line and line by-pass applications. Features: Compact size Cost effective products Ideal for across the line applications Safety Standard Recognized for AC applications Coated with flame-retardant epoxy resin (equivalent to UL94V-0 standards). RoHS Compliance Halogen free products are available Approval standards: Agencies UL CAS VDE, SEMKO, NEMKO, DEMKO, FIMKO, SEV, KEMA CQC KTL Standard NO. UL 1414 C22.2NO.1-04 IEC ed3 (2005) GB/T K Rated Voltage AH:250VAC AC:250VAC AH:250VAC AC:250VAC AH: X1 400VAC / Y1 250VAC,400VAC AC: X1 400VAC / Y2 250VAC AH: X1 400VAC / Y1 400VAC AC: X1 400VAC / Y2 250VAC AH: X1 400VAC / Y1 400VAC AC: X1 400VAC / Y2 250VAC Capacitance AH:2~4700 AH:2~4700 AH:2~4700 AH:2~4700 AH:2~4700 Value (pf) AC:2~10000 AC:2~10000 AC:2~10000 AC:2~10000 AC:2~10000 General specification: Capacitance Range AH:2pF to 4700pF; AC:2pF to 10000pF Capacitance Tolerance ±0.25pF, ±0. 5pF, ±5%, ±10%, ±20% Operating Temperature Range -25 C ~ 125 C Temperature Coefficient ( Rated Voltage C Max) 0±60PPM/ C(CH), -1000~+350PPM/ C(SL), ±10% (Y5P), % (Y5V), % (Y5U) AH Type : X1: 400Vac./ Y1 : 400Vac. or 250Vac; AC Type : X1 : 400Vac. / Y2 : 250Vac. Dissipation Factor(tanδ) or Q Insulation Resistance Dielectric Strength CH&SL: 30pF&above: 1000 Below 30PF: C, 1MHZ, 1±0.2Vrms Y5P:2.5% C, 1KHZ, 1±0.2Vrms Y5U: 2.5% C, 1KHZ, 1±0.2Vrms Y5V: 5.0% C, 1KHZ, 1±0.2Vrms 10000MΩ at 500VDC for 60 Seconds AC Type:1500VAC for 60 Seconds (Lead space=5mm) AC Type:2600VAC for 60 Seconds (Lead space=7.5 & 10 mm) AH Type:4000VAC for 60 Seconds(Lead space=10mm) 24

26 SAFETY.STANDARD CERAMIC CAPACITOR AH Type-Class X1/Y1 AC Type-Class X1/Y2 Typical Characteristic Curves: 25

27 SAFETY STANDARD CERAMIC CAPACITOR Detail Specification AH Type-Class X1/Y1 Part Number Temp. Char. Cap.(pF) Tol. Dimension (mm) D max. T max. F Wire Dia. YP0AH101K YP0AH151K YP0AH221K YP0AH331K Y5P ±10% YP0AH471K ± YP0AH561K YP0AH681K YP0AH102K YU0AH102M YU0AH152M YU0AH222M Y5U ±20% YU0AH332M ± YU0AH392M YU0AH472M YV0AH102M YV0AH152M YV0AH222M080 Y5V 2200 ±20% ± YV0AH332M YV0AH472M CH0AH***C060 2,3,4,5 ±0.25pF 7.0 CH0AH***D060 6,7,8,9,10 ±0.5pF 7.0 CH(NPO) CH0AH***J ±5% ± CH0AH***J070 15,18,20,22,24,27 ±5% 8.0 SL0AH***J060 15,18,20,22 24,27,30 33,36, SL ±5% ± SL0AH***J070 47,50,51,56, SL0AH820J080 68,75, SL0AH101J

28 SAFETY STANDARD CERAMIC CAPACITOR Detail Specification AC Type-Class X1/Y2 Part Number Temp. Char. Cap.(pF) Tol. YP0AC101K060 YP0AC151K YP0AC221K YP0AC331K YP0AC471K060 Y5P 470 ±10% 7.0 YP0AC561K YP0AC681K YP0AC821K YP0AC102K YU0AC102M060 YU0AC152M YU0AC222M Y5U ±20% YU0AC332M YU0AC392M YU0AC472M YV0AC102M060 YV0AC152M YV0AC222M YV0AC332M Y5V ±20% YV0AC392M YV0AC472M YV0AC682M = Lead : Please consult our part number explanation on page 23 for detail lead space, lead length, and lead configuration Dimension (mm) D max. T max. F Wire Dia. YV0AC103M ±1 CH0AC***C ,3,4,5 ±0.25pF 7.0 CH0AC***D060 6,7,8,9,10 ±0.5pF 7.0 CH0AC***J060 12,15 CH0AC***J070 CH(NPO) 18,20,22, CH0AC***J080 27,30,33 ±5% 9.0 CH0AC390J090 36, CH0AC470J SL0AC***J060 10,12,15,18,20 22,24,27,30,33 36,39,47,50,51 SL ±5% SL0AC***J070 52,62,68, SL0AC820J SL0AC101J ±1 10±1 7.5±1 10±1 7.5±1 7.5±1 10±1 7.5±1 10±

29 SAFETY STANDARD CERAMIC CAPACITOR Taping Specification and Dimension AH(X1Y1) : 25.4mm pitch/lead spacing 10.0mm taping Lead : *BAMD0 & *DAMD0 & *XAMD0 POE Part Number *BAMD0 & *DAMD0 & *XAMD0 Item Symbol Dimensions (mm) Pitch of component P 25.4±2 Pitch of sprocket P0 12.7±0.3 Lead spacing F 10.0±1.0 Length from hole center to component center P2 12.7±1.5 Length from hole center to lead P1 7.7±1.5 Body diameter D Refer to page 27 Deviation along tape, life or right S 0±2.0 Carrier tape width W /-0.5~0 Position of sprocket hole W1 9.0±0.5 Lead distance between the kink and center of sprocket hole Lead distance between the bottom of body and the center of sprocket hole H0 H /-1.5 For : *DAMD0 & *XAMD /-1.0 For : *BAMD0 Protrusion length 2.0 max(or the end of lead wire may be inside the tape) Diameter of sprocket hole D0 4.0±0.2 Lead diameter Ø d /-0.05 Total tape thickness t1 0.6±0.3 Total thickness, tape and lead wire t2 1.5 max. Deviation across tape h1 2.0 max. h2 2.0 max. Portion to cut in case of defect L 11.0 max. Hole-down tape width W0 11 max. Hole-down tape distortion W2 1.5±1.5 Coating extension on leads e 3.0 max for straight lead style; Not exceed the kink leads for kink lead. Body thickness T Refer to page 26 28

30 Marking : SAFETY STANDARD CERAMIC CAPACITOR Taping Specification and Dimension 1. Nominal Capacitance AH 2. Nominal Capacitance 3-digit-system 3. Capacitance Tolerance C:±0.25pF,D:±0.5pF,J:±5%,K:±10%,M:±20% 4. Company Name UK 5. Manufactured Date Abbreviation ex.: 6. Approved Monogram: (1) VDE approval mark IEC rd(2005). Class : X1:400V~, Y1:250V~or400V~ (2) UL approval mark (3) CSA approval mark (4) SEMKO approval mark (5) NEMKO approval mark (6) DEMKO approval mark (7) FIMKO approval mark (8) SEV approval mark (9) CQC approval mark Ex: One side: Two sides: *Marking by the stamp or laser. *The marking can be printed on either one side or two side of coating body. *C 71,Marked with code _ stand for Halogen and Pb free ; No marked with _ stand for Pb free. *When the TCC is Y5V(YV),there is a F between the AH and capacitance code. 29

31 SAFETY STANDARD CERAMIC CAPACITOR Taping Specification and Dimension AC (X1Y2) : 15mm pitch/lead spacing 7.5mm taping Lead : *BAFD7 & *DAFD7 & *XAFD7 25.4mm pitch/lead spacing 10.0mm taping Lead : *DAMD0 & *XAMD0 & *HAMD0 & *BAMD0 30

32 SAFETY STANDARD CERAMIC CAPACITOR Taping Specification and Dimension AC (X1Y2) : *BAMD0 POE Part Number *BAFD7 *DAFD7 *XAFD7 *DAMD0 *HAMD0 *XAMD0 Item Symbol Dimensions (mm) Dimensions (mm) Dimensions (mm) Pitch of component P Pitch of sprocket P0 15.0± ± ±0.3 Lead spacing F 7.5± ± ±1.0 Length from hole center to component center P2 7.5± ± ±1.5 Length from hole center to lead P1 3.75± ± ±1.5 Body diameter D Refer to page 27 Deviation along tape, life or right S 0±2.0 Carrier tape width W /-0.5~0 Position of sprocket hole W1 9.0±0.5 Lead distance between the kink and center of sprocket hole H / /-0 For: *DAMD0 *HAMD0 *XAMD0 Lead distance between the bottom of body and the center of sprocket hole H = /-1.0 For: *BAMD0 Protrusion length 2.0 max (Or the end of lead wire may be inside the tape) Diameter of sprocket hole D0 4.0±0.1 Lead diameter Ø d /-0.05 Total tape thickness t1 0.6±0.3 Total thickness, tape and lead wire t2 1.5 max. Deviation across tape h1 h2 2.0 max. 2.0 max. Portion to cut in case of defect L 11.0 max Hole-down tape width W min Hole-down tape distortion W2 1.5±1.5 Coating extension on leads e 3.0 max for straight lead style; Not exceed the kink leads for kink lead. Body thickness T Refer to page 27 31

33 SAFETY STANDARD CERAMIC CAPACITOR Taping Specification and Dimension Marking : 1. Nominal Capacitance AC 2. Nominal Capacitance 3-digit-system 3. Capacitance Tolerance C:±0.25pF,D:±0.5pF,J:±5%,K:±10%,M:±20% 4. Company Name UK 5. Manufactured Date Abbreviation ex.: 6. Approved Monogram: (1) VDE approval mark IEC rd(2005). Class : X1:400V~, Y2:250V (2) UL approval mark (3) CSA approval mark (4) SEMKO approval mark (5) NEMKO approval mark (6) DEMKO approval mark (7) FIMKO approval mark (8) SEV approval mark (9) CQC approval mark Ex: One side: Two sides: *Marking by the stamp or laser. *The marking can be printed on either one side or two side of coating body. *C 71,Marked with code _ stand for Halogen and Pb free ; No marked with _ stand for Pb free. 32

34 RADIAL AXIAL CAPACITOR Part Number Explanation To order, please also specify Pan Overseas Part No. as the following example for SAP system : RD21 B 102 K 500 B 5 C 07 B ➊ ➋ ➌ ➍ ➎ ➏ ➐ ➑ ➒ ➓ ➊ Product Type Product Type RD21 ➌ Capacitance RD20 ➋ Dielectric T.C. Operating Temperature Capacitance Change ( C) N NPO -55~+125 C 0 ± 30 (PPM / C) B X7R -55~+125 C ± 15% F Y5V -25~+85 C +30% ~ -80% Capacitance Capacitance Capacitance Capacitance pf pf pf pf 1R5 1.5 pf pf pf pf ➍ Tolerance Tolerance Tolerance Tolerance Tolerance J ± 5% K ± 10% M ± 20% Z +80% / -20% ➎ Rated Voltage Voltage Voltage Voltage Voltage Voltage V V V V V V V V V V ➏ Packaging ➐ Chip Size Packing Chip Size A B Ammo Bulk ➑ Termination Termination Termination Termination Termination Ag/Ni/Sn Cu/Ni/Sn A L Ag/Ni/Sn H C Cu/Ni/Sn Halogen free Halogen free ➒ -1 Length ➒ -2 Length Length (ex) Taping mm AN Ammo 3E 3.5 mm TN Reel mm ➓ Length Tolerance Length Tol. Length Tol. A ± 0.5 mm D Taping B ± 1.0 mm 33

35 MLC RADIAL LEAD CAPACITOR Features and Specification Features 1. MLC Radial Lead Capacitor (RD) has wide application in computer, data processing, telecommunication, industrial control and instrumentation equipment. 2. The radial lead MLC is built with superior moisture, and shock resistant epoxy coating material, can be supplied in both, bulk or taping form for automatic insertion. 3. RoHS compliance 4. Halogen free products are available Dimension (Unit: mm) Size Width Height Thickness Length Lead spacing Lead spacing Lead diameter (W) Max. (H) Max. (T) Max. (L) for Taping (F) for Bulk (F) (d) RD ± ± 1.0 Refer to the item 2.2 SAP Part Number RD ± ± ±

36 MLC RADIAL LEAD CAPACITOR Capacitance Range Capacitance Range Capactiance range Size Rated Voltage COG(NPO) Unit:pF X7R Unit:pf Y5V Unit:pf 10 VDC VDC VDC ~680000, , , , , , , ~680000, , , , , ~680000, , RD20, RD21 50 VDC 1~ ~ ~680000, VDC 1~ ~ ~ VDC 1~ ~ ~ VDC 1~ ~ ~ VDC 1~ ~ VDC 1~ ~ VDC VDC ~680000, , , 16 VDC , , , , ~680000, , 25 VDC , , , , , RD20, RD21 150~820000, 10000~680000, 50 VDC 10~ , VDC 10~ ~ ~ VDC 1.5~ ~ ~ VDC 1.5~ ~ ~ VDC 1.5~ ~ VDC 1.5~ ~ VDC 1.5~ ~ E12 series of IEC-63 Nominal Capacitance: 100/120/150/180/220/270/330/390/470/560/680/820 35

37 MLC RADIAL LEAD CAPACITOR Taping Specification & Packing Quantity Taping Specification : ITEM SYMBOL DIMENSIONS (mm) REMARKS Pitch of Components P 12.7 ± 0.1 Feed hole pitch PO 12.7 ± 0.3 Cumulative pitch error : ±1.0MM / 20pitches Feed hole center to lead P ± 0.7 Feed hole center to component center P ± 1.3 Lead diameter d 0.55 ± 0.05 Lead to lead spacing F / -0.2 To lead top within tolerance Component alignment, F - R h 2.0 max The alignment from the center of the lead is ±1.0MM Tape width W / -0.5 Adhesive tape width W min Hole position W1 9.0 ± 0.5 Adhesive tape position W2 3.0 max Height of bottom body form tape center H / -0 H mm H1 Lead-wire clinch height H ± H0 - W1 Component height H max Feed hoe diameter D0 4.0 ± 0.3 Total tape thickness T 0.7 ± 0.2 Packing Quantity : Bulk Taping Case Size Quantity per Bag Quantity per Ammo Box Quantity per Reel RD20, RD21 1,000 pcs 2,000 pcs 3,000 pcs 36

38 PLAN & MEMO