Switch & Outlet Boxes Technical Data

Transcription

1 Switch & Outlet Boxes Technical Data General Information: A box, with or without a bracket or bar hanger, intended for support of a fixture/luminaire weighing 50 lbs. or less is marked FOR FIXTURE/ LUMINAIRE SUPPORT on the carton to indicate that the box is intended for fixture/luminaire support. A box, with or without a bracket or bar hanger, intended for support of a fixture/luminaire weighing more than 50 lbs. is marked with the weight of the fixture/luminaire to be supported. Metallic device boxes and device plaster rings have not been investigated for support of a ceiling fixture/luminaire unless marked for use in ceilings, walls and with the weight of the product to be supported. Metallic device boxes intended to be installed in an existing structure have been investigated for the support of utilization equipment weighing not more than 6 lbs. Article 314 of the National Electrical Code (NEC ) covers the installation and use of boxes. The article includes table references that guide the electrician in the selection of the proper size box necessary to safely accommodate electrical service requirements. The box capacity table is reproduced in part from NEC as a quick reference and guide. The NEC should be consulted for complete details. Eaton s Crouse-Hinds Series products are produced in accordance with the requirements of UL514A, UL514B and UL514C, and are classified for fire resistance according to the standard, Fire Tests of Building Construction and Materials, ANSI/UL263, ASTM E 119 and NFPA 251. This listing is based on products when used in a fire rated (2 HR) wall or ceiling. Eaton s Crouse-Hinds Series steel boxes are listed with UL File No. E and Eaton s Crouse-Hinds Series non-metallic boxes are listed with UL File No. E and UL (2 HR fire rated) File No. R9933. Eaton s Crouse-Hinds Series switch and outlet boxes comply with the requirements of NEMA Standard OS-1, NFPA and Federal Spec. #W-J-800E. Under File No. E-23156, Eaton s Crouse-Hinds Series concentric and moon KO style boxes, the following is stated Suitable for bonding without any additional bonding means around concentric (or eccentric) knockouts where used in circuits above or below 250V. Wall thickness on all steel boxes is with minimum galvanization thickness of G60. Table (A) Metal Boxes Outlet Boxes Box Dimension (In.) Trade Size or Type Min. Cu. In. Cap. Maximum Number of Conductors (arranged by AWG size) No. 18 No. 16 No. 14 No. 12 No. 10 No. 8 No. 6 4 x 1 1 /4 Round or Octagonal x 1 1 /2 Round or Octagonal x 2 1 /8 Round or Octagonal x 1 1 /4 Square x 1 1 /2 Square x 2 1 /8 Square /16 x 1 1 /4 Square /16 x 2 1 /2 Square /16 x 2 1 /8 Square x 2 x 1 1 /2 Device x 2 x 2 Device x 2 x 2 1 /4 Device x 2 x 2 1 /2 Device x 2 x 2 3 /4 Device x 2 x 3 1 /2 Device x 2 1 /8 x 1 1 /2 Device x 2 1 /8 x 1 7 /8 Device x 2 1 /8 x 2 1 /8 Device /4 x 2 x 2 1 /2 Masonry Box/Gang /4 x 2 x 3 1 /2 Masonry Box/Gang FS-Minimum Internal Depth 1 3 /4 Single Cover Gang FD-Minimum Internal Depth 2 3 /8 Single Cover Gang FS-Minimum Internal Depth 1 3 /4 Multiple Cover Gang FD-Minimum Internal Depth 2 3 /8 Multiple Cover Gang Table (B) Volume Required per Conductor Size of Conductor No. 18 No. 16 No. 14 No. 12 No. 10 No. 8 No. 6 For SI units: one cubic inch = 16.4 cm 3. Free Space Within Box for Each Conductor 1.5 cubic inches 1.75 cubic inches 2 cubic inches 2.25 cubic inches 2.5 cubic inches 3 cubic inches 5 cubic inches Reprinted with permission from NFPA , the National Electrical Code, Copyright 2005 National Fire Protection Association, Quincy MA This reprinted material is not the complete and official position of the National Fire Protection Association, on the referenced subject which is represented only by the standard in its entirety. National Electrical Code and NEC are registered trademarks of the National Fire Protection Association, Inc., Quincy, MA US: CAN: Copyright 2015 Commercial Products Catalog

2 Switch & Outlet Boxes Technical Data OUTLET BOXES & COVERS Eaton s Crouse-Hinds Division has assembled one of the most complete outlet box product lines in the business. We ve been leading in quality and selection for decades, and throughout the steel outlet box offering, you will find innovative products and solutions that save labor, cut material costs and increase productivity. We have a complete offering of: 11 /16 square drawn and welded boxes 11 /16, switch, masonry, utility, outlet, ceiling, fan and gangable boxes 1 /2 and 3 /4 knockout covers products ground screw and lead installed Standard Materials Steel Covers, Outlet and Switch Boxes: BRACKETS USED ON BOXES F BRACKET D BRACKET S BRACKET C BRACKET Mounts on face of stud. See catalog number for set back. For wood studs. Side mount bracket with set up hook and guide tabs for automatic positioning. Standard bracket set back is 5 /8. For wood and metal studs. Side mount brackets with set up hook for wood or metal studs. Standard bracket set back is 5 /8. Ceiling box bracket for wood studs. Outlet Boxes VS BRACKET VMS BRACKET VP BRACKET SSB BRACKET Plain flat mounted bracket for use on wood or metal studs. No set back. Side bracket for use with wood or metal studs. Provides set up tabs to position on face of stud. Side bracket with set up hooks for wood studs. Positions box on either side of a steel stud. MSB BRACKET Position box on either side of steel stud. US: CAN: Copyright 2015 Commercial Products Catalog 173

3 Switch & Outlet Boxes Technical Data CLAMPS USED ON BOXES TP900 MC-BX NM-1 NM-2 NM-4 FOR ARMOURED & METAL- FOR NON-METALLIC CABLE CLAD (MCI) CABLE MOUNTING EARS TP901 TP902 ONE SCREW EAR TWO SCREW EAR Mounting ears are available on many of our switch boxes. They are set forward in 1 /16 the old way position. Two screw ears are generally used on shallow boxes and one screw ears on deep boxes. BOX ENTRY DETAILS Outlet Boxes 1 /2 Conduit KO 3 /4 Conduit KO 1 Conduit KO Concentric 1 /2 and 3 /4 KO Eccentric 1 /2 and 3 /4 KO Cable Pry-outs Always in Pairs and Pry-outs Conduit KOs have standard trade size dimensions. KOs are uniform and true for attachment of cable or conduit connectors. Pry-outs for cable entrance are slotted a twist with screwdriver removes them. KOs and pry-outs are precision stamped to permit easy removal, but remain sufficiently strong and sturdy when not removed. 4 square drawn boxes feature a 1 /2 and 3 /4 inverted concentric KO easily removed. Our 4 square welded boxes feature our 1 /2 eccentric KO which also features easy removability of both the 1 /2 and 3 /4 KOs. Note: These KOs are suitable for bonding without bonding jumpers around concentric (or eccentric) knockouts where used in circuits above or below 250V US: CAN: Copyright 2015 Commercial Products Catalog

4 Steel Square Boxes 4 SQUARE OUTLET BOXES & COVERS Applications: Features: the installation of electrical devices (switches, receptacles, fans, lights, etc.) installation increased labor savings above or below 250 volts needs Certifications and Compliances: 4 SQUARE OUTLET BOXES 18.0 CUBIC INCH CAPACITY 1 1 /4 DEEP FOR CONDUIT TP408 Bracket TP408 - Drawn 1 /2 1 / US: CAN: Copyright 2015 Commercial Products Catalog 175

5 Steel Square Boxes 4 SQUARE OUTLET BOXES 22.0 CUBIC INCH CAPACITY (WELDED) 21.0 CUBIC INCH CAPACITY (DRAWN) 1 1 /2 DEEP FOR CONDUIT TP404/TP404PF TP404SSB TP404MSB TP404RED TP425 TP469 TP830* TP405 TP412 TP839* TP410 TP414RED TP414 TP418 TP423RED Metal Stud Sizes Bracket TP404** - - Welded 8-1 /2, 4-1 /2 + 3 /4 E 2-1 /2, 2-1 /2 + 3 /4 E TP404MSB - MSB Welded 8-1 /2, 4-1 /2 + 3 /4 E 2-1 /2, 2-1 /2 + 3 /4 E TP404RED - - Welded 8-1 /2, 4-1 /2 + 3 /4 E 2-1 /2, 2-1 /2 + 3 /4 E TP404REDMSB - MSB Welded 8-1 /2, 4-1 /2 + 3 /4 E 2-1 /2, 2-1 /2 + 3 /4 E TP404PF ** - - Welded 8-1 /2, 4-1 /2 + 3 /4 E 2-1 /2, 2-1 /2 + 3 /4 E TP404SSB - SSB Welded 8-1 /2, 4-1 /2 + 3 /4 E 2-1 /2, 2-1 /2 + 3 /4 E TP425** All "VP" Welded 6-1 /2, 3-1 /2 + 3 /4 E 2-1 /2, 2-1 /2 + 3 /4 E TP423** All "VMS" Welded 6-1 /2, 3-1 /2 + 3 /4 E 2-1 /2, 2-1 /2 + 3 /4 E TP423RED All "VMS" Welded 6-1 /2, 3-1 /2 + 3 /4 E 2-1 /2, 2-1 /2 + 3 /4 E TP Drawn 4-1 /2, 6-1 /2 + 3 /4 C 3-1 /2, 2-3 / TP Drawn 12-1 /2 5-1 / TP Drawn 8-3 /4 3-1 /2, 2-3 / TP Drawn 8-1 /2, 4-3 /4 3-1 /2, 2-3 / TP414RED - - Drawn 8-1 /2, 4-3 /4 3-1 /2, 2-3 / TP418 - "F", Set Flush Welded 6-1 /2, 3-1 /2 + 3 /4 E 2-1 /2, 2-1 /2 + 3 /4 E TP Welded 8-3 /4 2-1 /2, 2-1 /2 + 3 /4 E TP467MSB - MSB Welded 8-3 /4 2-1 /2, 2-1 /2 + 3 /4 E TP469 All "VMS" Welded 6-3 /4 2-1 /2, 2-1 /2 + 3 /4 E Air Plenum TP830* - - Drawn 8-1 /2, 4-3 /4 3-1 /2, 2-3 / TP839* - - Drawn 8-3 /4 C 3-1 /2, 2-3 / *For Air Plenum (no mounting holes) - not UL Listed. **cul Listed. All welded 4 Square Outlet Boxes have a raised dimple for ground screw. TP404PF includes ground screw with pigtail lead US: CAN: Copyright 2016 Commercial Products Catalog

6 Steel Square Boxes 4 SQUARE OUTLET BOXES 22.0 CUBIC INCH CAPACITY 1 1 /2 DEEP FOR NON-METALLIC CABLE CLAMPS IN EACH END TP444 TP444MSB TP449 TP446 Bracket TP444 - Welded 4 - Cable, 4-1 /2, 2-1 /2 + 3 /4 E 1-1 / TP444MSB MSB Welded 4 - Cable, 4-1 /2, 2-1 /2 + 3 /4 E 1-1 / TP444SSB SSB Welded 4 - Cable, 4-1 /2, 2-1 /2 + 3 /4 E 1-1 / TP446 F, Set Flush Welded 4 - Cable, 2-1 /2, 1-1 /2 + 3 /4 E 1-1 / TP449 VMS Welded 4 - Cable, 2-1 /2, 1-1 /2 + 3 /4 E 1-1 / SQUARE OUTLET BOXES 22.0 CUBIC INCH CAPACITY 1 1 /2 DEEP FOR ARMOURED & METAL-CLAD (MCI) CABLE & HCF CABLE CLAMPS IN EACH END TP454 TP454MSB TP456 TP459 Bracket TP459 VMS Welded 4 - Cable, 2-1 /2, 1-1 /2 + 3 /4 E 1-1 / TP454* - Welded 4 - Cable, 4-1 /2, 2-1 /2 + 3 /4 E 1-1 / TP454MSB MSB Welded 4 - Cable, 4-1 /2, 2-1 /2 + 3 /4 E 1-1 / TP454PF - Welded 4 - Cable, 4-1 /2, 2-1 /2 + 3 /4 E 1-1 / TP454SSB* SSB Welded 4 - Cable, 4-1 /2, 2-1 /2 + 3 /4 E 1-1 / TP456* F, Set Flush Welded 4 - Cable, 2-1 /2, 1-1 /2 + 3 /4 E 1-1 / TP456PF F, Set Flush Welded 4 - Cable, 2-1 /2, 1-1 /2 + 3 /4 E 1-1 / *UL approved for use with aluminum interlocking grounding metal-clad cable, Type MCIA (Southwire MCAP ). MCAP is a registered trademark of Southwire Company. TP catalog numbers ending in PF include ground screw with pigtail lead. US: CAN: Copyright 2016 Commercial Products Catalog 177

7 Steel Square Boxes 4 SQUARE OUTLET BOXES 30.3 CUBIC INCH CAPACITY 2 1 /8 DEEP FOR CONDUIT TP403/TP403PF TP403SSB TP403MSB TP432 TP432VMS TP434 TP438 TP831* TP403RED TP434RED TP451RED TP451 Bracket *For Air Plenum (no mounting holes) - not UL Listed. **cul Listed. TP catalog numbers ending in PF include ground screw with pigtail lead. TP403** - Welded 8-1 /2, 4-1 /2 + 3 /4 E 2-1 /2, 2-1 /2 + 3 /4 E TP403MSB MSB Welded 8-1 /2, 4-1 /2 + 3 /4 E 2-1 /2, 2-1 /2 + 3 /4 E TP403RED - Welded 8-1 /2, 4-1 /2 + 3 /4 E 2-1 /2, 2-1 /2 + 3 /4 E TP403REDMSB MSB Welded 8-1 /2, 4-1 /2 + 3 /4 E 2-1 /2, 2-1 /2 + 3 /4 E TP403PF ** - Welded 8-1 /2, 4-1 /2 + 3 /4 E 2-1 /2, 2-1 /2 + 3 /4 E TP403SSB SSB Welded 8-1 /2, 4-1 /2 + 3 /4 E 2-1 /2, 2-1 /2 + 3 /4 E TP432** - Welded 8-3 /4 2-1 /2, 2-1 /2 + 3 /4 E TP432MSB MSB Welded 8-3 /4 2-1 /2, 2-1 /2 + 3 /4 E TP432REDMSB MSB Welded 8-3 /4 2-1 /2, 2-1 /2 + 3 /4 E TP432VMS VMS Welded 6-3 /4 2-1 /2, 2-1 /2 + 3 /4 E TP436 - Welded /2, 2-1 /2 + 3 /4 E TP436MSB MSB Welded /2, 2-1 /2 + 3 /4 E TP434 - Drawn 8-1 /2, 4-3 /4 3-1 /2, 2-3 / TP434RED - Drawn 8-1 /2, 4-3 /4 3-1 /2, 2-3 / TP438 - Drawn 4-1 /2, 6-1 /2 + 3 /4 C 3-1 /2, 2-3 / TP438PF - Drawn 4-1 /2, 6-1 /2 + 3 /4 C 3-1 /2, 2-3 / TP451 VMS Welded 6-1 /2, 3-1 /2 + 3 /4 E 2-1 /2, 2-1 /2 + 3 /4 E TP451PF VMS Welded 6-1 /2, 3-1 /2 + 3 /4 E 2-1 /2, 2-1 /2 + 3 /4 E TP451RED VMS Welded 6-1 /2, 3-1 /2 + 3 /4 E 2-1 /2, 2-1 /2 + 3 /4 E TP437 VP Welded 6-1 /2, 3-1 /2 + 3 /4 E 2-1 /2, 2-1 /2 + 3 /4 E Air Plenum TP831* - Drawn 8-1 /2, 4-3 /4 3-1 /2, 2-3 / US: CAN: Copyright 2016 Commercial Products Catalog

8 Steel Square Boxes 4 SQUARE OUTLET BOXES 30.3 CUBIC INCH CAPACITY 2 1 /8 DEEP FOR NON-METALLIC CABLE CLAMPS IN EACH END TP450 TP450MSB TP450SSB TP452 Bracket TP450 - Welded 1 /2 1 /2 + 3 /4 E 1 / TP450MSB MSB Welded 1 /2 1 /2 + 3 /4 E 1 / TP450SSB SSB Welded 1 /2 1 /2 + 3 /4 E 1 / TP452 VMS Welded 1 /2 1 /2 + 3 /4 E 1 / SQUARE OUTLET BOXES 30.3 CUBIC INCH CAPACITY 2 1 /8 DEEP FOR ARMOURED & METAL-CLAD (MCI) CABLE & HCF CABLE CLAMPS IN EACH END TP431 TP431MSB TP440 Metal Stud Sizes Bracket TP431* - - Welded 1 /2 1 /2 & 3 /4 E 1 / TP431PF - - Welded 1 /2 1 /2 & 3 /4 E 1 / TP431MSB - MSB Welded 1 /2 1 /2 & 3 /4 E 1 / TP431SSB* - SSB Welded 1 /2 1 /2 & 3 /4 E 1 / TP440* All VMS Welded 1 /2 1 /2 & 3 /4 E 1 / *UL approved for use with aluminum interlocking grounding metal-clad cable, Type MCIA (Southwire MCAP ). MCAP is a registered trademark of Southwire Company. TP catalog numbers ending in PF include ground screw with pigtail lead. US: CAN: Copyright 2015 Commercial Products Catalog 179

9 Steel Square Boxes 4 SQUARE TWO DEVICE BOXES 30.3 CUBIC INCH CAPACITY 2 1 /8 DEEP FOR CONDUIT TP391 TP395 Bracket TP391 VS, Set 7 /8 Drawn 1 /2 3 /4 1 /2 3 / TP395 - Drawn 1 /2 3 /4 1 /2 3 / SQUARE OUTLET BOXES 46.0 CUBIC INCH CAPACITY 3 1 /2 DEEP FOR CONDUIT, FILE NO. E Applications: 1 /2 deep outlet boxes are ideal for applications requiring increased capacity, including the installation of speaker boxes, fire alarms, strobes, security cameras and other oversized devices TP411 TP411RED TP413 TP413RED Bracket TP411 Side Welded 1 /2 + 3 /4 C 1 /2 + 3 /4 C TP411RED Side Welded 1 /2 + 3 /4 C 1 /2 + 3 /4 C TP413 - Welded 1 /2 + 3 /4 C 1 /2 + 3 /4 C TP413RED - Welded 1 /2 + 3 /4 C 1 /2 + 3 /4 C US: CAN: Copyright 2015 Commercial Products Catalog

10 Steel Square Covers 4 SQUARE EXTENSION RINGS 1 1 /2 DEEP WITH CONDUIT KNOCKOUTS 21.0 CUBIC INCH CAPACITY 2 1 /8 DEEP WITH CONDUIT KNOCKOUTS 30.3 CUBIC INCH CAPACITY TP424 TP422 TP426 TP428RED TP443 (2 1 /8 Deep) TP428, TP833* 1 1 /2 Deep TP424 1 / TP426 3 / TP428 1 /2 3 / TP428RED 1 /2 3 / TP833* 1 /2 3 / /8 Deep TP443 1 /2 3 / TP /2 Deep Switch & Masonry Box Extension Ring TP422 1 /2 1 /2 + 3 /4 E *For Air Plenum (no mounting holes). Requires the use of TP854; purchase separately - not UL Listed. For use as extension with switch box, not four square box. FLEXIBLE FIXTURE HANGERS TPSFH Square Flexible Fixture Hangers are used in commercial or light industrial applications where HID high bay and low bay lighting fixtures are used. Specific applications include storage facilities, shipping warehouses, retail and DIY facilities. Features: 1 /2 or 3 /4 fixture conduit stems, these hangers allow the conduit stem of the fixture (luminaire) to swing in any direction; maximum swing angle is 26 from vertical max. slope angles 22 1 /2 Certifications and Compliances: Standard Materials and Finishes: 3 /4 conduit stem as standard and come supplied with a 3 /4 1 /2 reducer for 1 /2 conduit stem applications TPSFH12 For use with 4 Square Boxes Support Wt. (Lbs.) 50 US: CAN: Copyright 2015 Commercial Products Catalog 181

11 Steel Square Covers COVERS FOR 4 SQUARE BOXES CUBIC INCH CAPACITY (SEE BELOW) #8-32 Screw Used on Covers TP472 TP472RED TP474 TP478 TP487 TP850* Flat Blank Gasketed with Captive Screws TP854* Flat Ring Double Gasketed *For Air Plenum (no mounting holes) - not UL Listed. **ETL listed. CSA certified. TP473, TP475, TP476, TP477, TP479, TP483 MUD RINGS FOR 4 SQUARE STEEL OUTLET BOXES TP850* TP854* AMR0 TP472 Flat Blank TP472RED Flat Blank, Red TP474 Flat, Open with Ears 2 3 / TP478 Flat, with 1 /2 KO TP487 Flat, with 3 /4 KO TP473 Raised 1 /4, Open with Ears 2 3 / TP476 Raised 1 /2, Open with Ears 2 3 / TP477 Raised 5 /8, Open with Ears 2 3 / TP475 Raised 3 /4, Open with Ears 2 3 / TP479 Raised 1, Open with Ears 2 3 / TP483 Raised 1 1 /4, Open with Ears 2 3 / AMR0** 3 /4-1 1 /2 Round Adjustable Mud Ring Air Plenum Capacity Cu. In. TP480 One Device TP482, TP484, TP486, TP489 TP494 TP488, TP490 TP496, TP499, TP500, TP501, TP502 AMR1 AMR2 AMR158 TP494 Flat TP496 1 /4 Raised TP498 1 /2 Raised TP499 5 /8 Raised TP500 3 /4 Raised TP /4 Raised TP502 1 Raised AMR2** 5 /8-1 1 /2 Raised Adjustable **culus Listed. CSA certified. Slotted design for use with 4 square box partitions. TP480 Flat TP482 1 /4 Raised TP484 1 /2 Raised TP489 5 /8 Raised TP486 3 /4 Raised TP488 1 Raised TP /4 Raised AMR1** 3 /4-1 1 /2 Raised Adjustable AMR158** 5 /8-1 1 /4 Raised Adjustable Two Device Capacity Cu. In US: CAN: Copyright 2015 Commercial Products Catalog

12 Steel Square Covers METALGUARD PROTECTIVE PLATES Applications: rings; with or without devices, switches, GFCI, etc. installed Features: its wiring free from contaminants speeds up trim process screwdriver into the slot in front, turn and pull them out Pre-fabricated Box, Cover, Ground Screw & Lead Assembly 4 SQUARE SURFACE COVERS 5.5 CUBIC INCH CAPACITY RAISED 1 /2 CSA LISTED Standard Material & Finish: MGRK Contractor Kit (120-1G, 40-2G, 20-3G, 5-4G, and 20-Rnd) MGR1 1G Residential Wire Protector MGR2 2G Residential Wire Protector MGR4 4G Residential Wire Protector MGR0 Rnd Residential Wire Protector MGMR1 1G Wire Protector for Commercial MR MGMR2 2G Wire Protector for Commercial MR MGMR0 Rnd Wire Protector for Commercial MR Screw(s) provided in raised cover kit are for use with the center hole on duplex receptacles. Nuts that are provided in kit are to be used in conjunction with the screws that are provided as standard packaging with devices to mount device to raised cover. For GFCI device installation, no screw is needed; please disregard. TP503 TP504 TP506 TP508 TP510 TP512 TP507, TP514, TP519 TP516 TP509 (4 Screws), TP518 (2 Screws) TP513 TP511 TP515 TP517 TP503 Raised Blank TP504 For One Toggle Switch and One Single Receptacle 1 13 /32 Dia TP506 For One Toggle Switch and One Duplex Receptacle TP508 For Two Toggle Switches TP510 For Two Duplex Receptacles TP512 For One Toggle Switch TP507 For One 20 Amp Single Receptacle 1 19 /32 Dia TP514 For One Single Receptacle 1 13 /32 Dia TP519 For One 30 Amp Twist-Lock Single Receptacle 1 23 /32 Dia TP516 For One Duplex Receptacle TP509 For One Amp Receptacle (4-wire) 2 7 /16 Dia TP518 For One Amp Receptacle 2 9 /64 Dia TP513 For One GFCI Receptacle TP511 For Two GFCI Receptacles TP515 For One Toggle Switch and One GFCI Receptacle TP517 For One Duplex Receptacle and One GFCI Receptacle US: CAN: Copyright 2015 Commercial Products Catalog 183

13 Steel Square Covers UNI-MOUNT COVERS The Uni-Mount combines the features of a mounting device plate with those of a box support, giving you one universal plate for all of your needs. Specifically designed for use with metal or wood studs: The new and improved version incorporates four small holes on the left side (support side) of the bracket. These holes allow for the attachment of box mounting brackets to allow for use of both sides of the stud. The holes are strategically located to accept either the Eaton s B-Line Series BB423 bracket or the Caddy H23 bracket. Additionally, the viewing hole has been significantly enlarged (and is now diamond shaped) to make it even easier to find mark lines on the stud. Features: 1 /2, 5 /8 and 3 /4 raised stock without a box *CSA requires a far side support. Single Gang Two Gang Capacity Cu. In. Single Gang TP /2 Raised TP /8 Raised TP /4 Raised Two Gang TP /2 Raised TP /8 Raised TP /4 Raised Low Profile Screws Reduces Risk of Sheetrock Bulge TP710 L.P. Screws US: CAN: Copyright 2015 Commercial Products Catalog

14 Steel Square Covers TILE WALL COVERS FOR 4 SQUARE BOXES CUBIC INCH CAPACITY (SEE BELOW) TP524 Applications: TP534 TP540 Features: Capacity Cu. In. One Device TP520 1 /2 Raised TP522 3 /4 Raised TP524 1 Raised TP /4 Raised TP /2 Raised TP530 2 Raised Two Device TP532 1 /2 Raised TP534 3 /4 Raised TP536 1 Raised TP /4 Raised TP /2 Raised TP542 2 Raised SQUARE BOX PARTITIONS TP860 TP861 TP862 TP863 For 1 1 /2 Deep Box with Square Cut Tile Wall Two Gang Covers TP860 For 1 /2, 3 /4, 1 Raised Covers TP861 For 1 1 /4, 1 1 /2, 2 Raised Covers For 2 1 /8 Deep Box with Square Cut Tile Wall Two Gang Covers TP862 For 1 /2, 3 /4, 1 Raised Covers TP863 For 1 1 /4, 1 1 /2, 2 Raised Covers US: CAN: Copyright 2015 Commercial Products Catalog 185

15 Steel Square Boxes 4 11 /16 SQUARE OUTLET BOXES & COVERS Applications: For use with conduit For use in commercial and industrial applications, where larger sized conductor or wiring devices are needed and additional volume is required Available in red for fire alarm applications Features: Ideal for exposed work applications, providing an easy method for the installation of electrical devices (switches, receptacles, fans, lights, etc.) Raised ground screw location in the welded boxes saves time in installation Concentric knockouts have a 1 /2 and 3 /4 knockout in the same location for customer flexibility are suitable for use without a bonding jumper in circuits above or below 250 volts Available in two depths for differing cubic capacity requirements Welded or drawn construction to match customer preference Extensive cover offering to meet various customer applications and needs Certifications and Compliances: UL Listed 4 11 /16 SQUARE OUTLET BOXES 29.5 CUBIC INCH CAPACITY 1 1 /2 DEEP WITH CONDUIT KOs TP523 TP548 TP549 TP catalog numbers ending in PF include ground screw with pigtail lead. TP523 Welded 12-1 /2 + 3 /4 C 2-1 /2, 2-3 / TP523PF Welded 12-1 /2 + 3 /4 C 2-1 /2, 2-3 / TP548 Drawn 8-1 /2, 4-3 /4 3-1 /2, 2-3 / TP549 Drawn 6-1 /2, 6-1 /2 + 3 /4 C 3-1 /2, 2-3 / US: CAN: Copyright 2016 Commercial Products Catalog

16 Steel Square Boxes 4 11 /16 SQUARE OUTLET BOXES 42.0 & 44.0 CUBIC INCH CAPACITY 2 1 /8 DEEP WITH CONDUIT KOs TP563 TP554 TP842* TP556 TP832* TP556RED TP558 TP835* TP560 TP836* TP562 TP557 TP521 TP525 Bracket *For Air Plenum (no mounting holes) - not UL Listed. **Raised ground bump contains holes for two ground screws. TP catalog numbers ending in PF include ground screw with pigtail lead. Not UL Listed Cubic Inch Capacity TP563 Drawn /2, 6-1 /2 + 3 /4 C 3-1 /2, 2-3 / TP554 Drawn /4 3-1 /2, 2-3 / TP556 Drawn /2, 4-3 /4 3-1 /2, 2-3 / TP556PF Drawn /2, 4-3 /4 3-1 /2, 2-3 / TP556RED Drawn /2, 4-3 /4 3-1 /2, 2-3 / TP558 Drawn /4, /2, 2-3 / TP558PF Drawn /4, /2, 2-3 / TP560 Drawn /2, 2-3 / TP562 Drawn /4 3-1 /2, 2-3 / TP557 Drawn VS 5-1 /2, 4-1 /2 + 3 /4 C 3-1 /2, 2-3 / Cubic Inch Capacity TP521 Welded /2 + 3 /4 C 2-1 /2, 2-3 / TP521PF Welded /2 + 3 /4 C 2-1 /2, 2-3 / TP525** Welded /2 + 3 /4 E 2-1 /2, 2-1 /2 + 3 /4 E TP525PF Welded /2 + 3 /4 E 2-1 /2, 2-1 /2 + 3 /4 E Air Plenum TP835* /4, /2, 2-3 / TP836* /2, 2-3 / TP842* /4 3-1 /2, 2-3 / TP832* /2, 4-3 /4 3-1 /2, 2-3 / US: CAN: Copyright 2016 Commercial Products Catalog 187

17 Steel Square Covers 4 11 /16 SQUARE EXTENSION RINGS 1 1 /2 DEEP WITH CONDUIT KOs 29.5 CUBIC INCH CAPACITY 2 1 /8 DEEP WITH CONDUIT KOs 42.0 CUBIC INCH CAPACITY TP550 TP564 TP837* TP564RED 1 1 /2 Deep 29.5 Cubic Inch Capacity TP550 1 /2 3 / /8 Deep 42.0 Cubic Inch Capacity TP564 1 /2 3 / TP564RED 1 /2 3 / Air Plenum TP837* 2 1 /8 Deep 1 /2 3 / *For Air Plenum (no mounting holes) - not UL Listed. TP837 requires the use of TP852, purchased separately US: CAN: Copyright 2015 Commercial Products Catalog

18 Steel Square Covers 4 11 /16 SQUARE COVERS CUBIC INCH CAPACITY (SEE BELOW) TP568 TP568RED TP569, TP570, TP571, TP573, TP575 TP572 TP574 - TP582, TP529, TP531 TP584, TP586, TP589, TP593, TP541, TP543 TP851* TP852* Flat and Raised *For Air Plenum (no mounting holes). CSA certified. Not UL Listed. Capacity Cu. In. TP568 Flat Blank TP568RED Flat Blank, Red TP569 1 /2 Raised, with Ears 2 3 / TP570 5 /8 Raised, with Ears 2 3 / TP571 3 /4 Raised, with Ears 2 3 / TP572 Flat, with 1 /2 KO TP573 1 Raised, with Ears 2 3 / TP /4 Raised, with Ears 2 3 / Air Plenum TP851* Flat Blank Gasketed with Captive Screws TP852* Flat Ring Double Gasketed One Device TP574 1 /4 Raised TP576 1 /2 Raised TP578 3 /4 Raised TP579 5 /8 Raised TP580 1 Raised TP /4 Raised TP /2 Raised TP531 2 Raised Two Device TP590 Flat TP583 1 /4 Raised TP584 1 /2 Raised TP587 5 /8 Raised TP586 3 /4 Raised TP589 1 Raised TP /4 Raised TP /2 Raised TP543 2 Raised US: CAN: Copyright 2015 Commercial Products Catalog 189

19 Steel Square Covers 4 11 /16 SQUARE SURFACE COVERS 9.0 CUBIC INCH CAPACITY 1 /2 RAISED TP720 TP722 TP724, TP730, TP736 TP726 TP728 TP732 TP734 TP738 TP740 TP720 For One Toggle Switch TP722 For One Duplex Receptacle TP724 For One Single Receptacle 1 13 /32 Dia TP730 For One 20 Amp Single Receptacle Dia TP736 For One Dia. Power Outlet TP726 For Two Toggle Switches TP728 For Two Duplex Receptacles TP732 For One Dia. Range/Dryer Receptacle TP734 For One Dia. Power Outlet TP738 For One Ground Fault Interrupter TP740 For One GFI Receptacle and One Toggle TP741 For Two GFI Receptacles US: CAN: Copyright 2015 Commercial Products Catalog

20 Steel Utility Boxes & Covers UTILITY BOXES CUBIC INCH CAPACITY (SEE BELOW) 4 LONG x 2 1 /8 WIDE TP588, TP647 TP591 TP592, TP600, TP602 TP598, TP605 TP594, TP596 TP604, TP606 Bracket 1 1 /4 Deep 8.5 Cubic Inch Capacity TP647-1 /2 1 / /2 Deep 10.3 Cubic Inch Capacity TP588-1 /2 1 / TP591 F, Set 1 /4 1 /2 1 / /2 Deep Extension Rings 10.3 Cubic Inch Capacity TP592-1 / /8 Deep 13.0 Cubic Inch Capacity TP594-1 /2 1 / TP596-3 /4 1 / TP598 S, Set 1 /2 1 /2 1 / /8 Deep Extension Rings 13.0 Cubic Inch Capacity TP600-1 / TP602-3 / /8 Deep 14.5 Cubic Inch Capacity TP604-1 /2 1 / TP606-3 /4 1 / TP605 S, Set 1 /2 1 /2 1 / UTILITY BOX COVERS TP608 TP610 TP612 TP613 TP614 TP616 TP618 TP608* Blank TP610* For 20 and 30 Amp, Twist Lock, 1 19 /32 Dia TP612* Single Receptacle, 1 13 /32 Dia TP613* For GFCI Device TP614* 1 /2 KO TP616* Duplex Receptacle TP618* One Toggle Switch *CSA certified. US: CAN: Copyright 2015 Commercial Products Catalog 191

21 Steel Switch Boxes 1 DEEP NON-GANGABLE 6.5 CUBIC INCH CAPACITY 1 15 /16 WIDE x 3 3 /4 LONG TP101 TP103 Bracket Plastic Clamp Conduit TP101 S No 1 / TP103 S Yes 1 / Cable 1 1 /2 DEEP NON-GANGABLE 7.5 CUBIC INCH CAPACITY 2 WIDE x 3 LONG TP100 TP104 TP106 TP114 Bracket Ears Each End Each Side For Non-metallic Cable Clamps in Each End TP100 - Yes - 1 / TP104 S, Set 1 / / For Armoured & Metal-clad (MCI) Cable Clamps in Each End TP106* - Yes 2 - Cable - 1 / For Conduit No Clamps, Flush Device TP114 - Yes 1 /2-1 / *UL approved for use with aluminum interlocking grounding metal-clad cable, Type MCIA (Southwire MCAP ). MCAP is a registered trademark of Southwire Company US: CAN: Copyright 2015 Commercial Products Catalog

22 Steel Switch Boxes 2 DEEP GANGABLE 10.0 CUBIC INCH CAPACITY 2 WIDE x 3 LONG TP116 TP118 TP120 TP123 TP124 TP126 TP130 TP132 TP131 Hold-Tite Bracket Ears Each End Each Side For Non-metallic Cable Clamps in Each End TP116 - Yes 2 - Cable - 1 / TP118 S, Set 5 /8-2 - Cable - 1 / For Armoured & Metal-clad (MCI) Cable Clamps in Each End TP120* - Yes 2 - Cable - 1 / TP123* F, Set 1 /2-2 - Cable - 1 / TP124* S, Set 5 /8-2 - Cable - 1 / For Conduit No Clamps, Flush Device TP /2 1 /2 1 / TP130 - Yes 1 /2 1 /2 1 / TP132 S, Set 5 /8-1 /2 1 /2, 1 Side 1 / TP131 Hold-Tite Yes 1 /2 - T - 1 / *UL approved for use with aluminum interlocking grounding metal-clad cable, Type MCIA (Southwire MCAP ). MCAP is a registered trademark of Southwire Company. US: CAN: Copyright 2015 Commercial Products Catalog 193

23 Steel Switch Boxes 2 1 /4 DEEP GANGABLE BEVELED CORNERS 10.5 CUBIC INCH CAPACITY 2 WIDE x 3 LONG TP134 TP137 Hold-Tite TP138 Ears Bumps Clamp Screws Through Beveled Corners Each End Each Side TP134 Gangable - Yes 2 - Cable - 1 / TP137 Gangable Yes Cable - 1 / TP138 Gangable Yes Cable - 1 / /2 DEEP GANGABLE 12.5 CUBIC INCH CAPACITY 2 WIDE x 3 LONG TP158 TP162 TP163 TP164, TP168 TP170 TP161 TP172 TP174 TP171 Ground Leveling Bracket Ears Pigtail Bumps Each End Each Side For Non-metallic Cable Clamps in Each End TP Yes 1 /2-1 / TP115* - Yes Yes - 1 /2 1 / TP161 Snap-in Yes / TP162 - Yes /2 1 / TP163 Hold-Tite Yes / TP164 F, Set 1 / /2 1 /2 1 / TP168 F, Set 1 / /2 1 /2 1 / TP170 S, Set 5 / /2 1 /2 1 / TP172 D, Set 5 / /2 1 /2 1 / TP174 D, Set 5 /8 - Yes - 1 /2 1 /2 1 / TP171 VP, Set 1 / /2 1 /2 1 / *Not UL Listed US: CAN: Copyright 2015 Commercial Products Catalog

24 Steel Switch Boxes 2 1 /2 DEEP GANGABLE 12.5 CUBIC INCH CAPACITY 2 WIDE x 3 LONG FOR ARMOURED & METAL-CLAD (MCI) CABLE CLAMPS IN EACH END TP177 TP178 TP179 Hold-Tite TP180 TP184 TP185 Bracket Ears Each End Each Side TP177* Snap-in Yes 2 - Cable 1 / TP178* - Yes 2 - Cable 1 /2 1 / TP179* Hold-Tite Yes 2 - Cable - 1 / TP180* F, Set 1 /2-1 /2 1 /2 1 / TP184* S, Set 5 /8-1 /2 1 /2 1 / TP185* VP, Set 1 /2-1 /2 1 /2 1 / *UL approved for use with aluminum interlocking grounding metal-clad cable, Type MCIA (Southwire MCAP ). MCAP is a registered trademark of Southwire Company. GANG BOXES SET BACK 1 /2 2 1 /2 DEEP 3 3 /4 HIGH 1 /2 & 3 /4 CONCENTRIC KOs TP632 TP633 TP637 TP638 Gang Bracket Width Each End Each Side Capacity Cu. In. TP632 3 VP 5 9 / TP633 4 VP 7 3 / TP637 3 VS 5 9 / TP638 4 VS 7 3 / US: CAN: Copyright 2015 Commercial Products Catalog 195

25 Steel Switch Boxes 2 1 /2 DEEP GANGABLE 12.5 CUBIC INCH CAPACITY 2 WIDE x 3 LONG FOR CONDUIT NO CLAMPS TP214 TP216 TP217 TP218 TP220 TP222 TP224 Bracket Ears Leveling Bumps Each End Each Side TP Yes 1 /2-1 / TP216 Snap-in Yes - 1 /2 1 / TP217 - Yes - 1 /2-1 / TP218 - Yes - 1 /2 1 /2 1 / TP220 F, Set 1 / /2 1 /2, 1 Side 1 / TP222 S, Set 5 / /2 1 /2, 1 Side 1 / TP224 Hold-Tite Yes - 1 /2-1 / US: CAN: Copyright 2015 Commercial Products Catalog

26 Steel Switch Boxes 2 1 /2 DEEP SWITCH BOXES INSTANT ON 12.5 CUBIC INCH CAPACITY 2 WIDE x 3 LONG WITH BUMPS CLAMPS IN EACH END (BUMPS LEVEL THE BOX AGAINST THE SIDE OF STUD, TOP TO BOTTOM, FRONT TO BACK) TP210 TP213 Clamps Nails Each End Each Side TP210 NM Cable Angle 1 /2-1 / TP213 Armoured Cable Angle 1 /2-1 / /4 DEEP GANGABLE 14.0 CUBIC INCH CAPACITY 2 WIDE x 3 LONG TP660 TP662 TP664 TP668 TP670 Bracket Ears Each End Each Side For Non-metallic Cable Clamps in Each End TP /2 1 / TP662 - Yes 1 /2 1 / TP664 S, Set 5 /8-1 /2 1 / For Armoured & Metal-clad (MCI) Cable Clamps in Each End TP668* - Yes 1 /2 1 / TP670* S, Set 5 /8-1 /2 1 / *UL approved for use with aluminum interlocking grounding metal-clad cable, Type MCIA (Southwire MCAP ). MCAP is a registered trademark of Southwire Company. US: CAN: Copyright 2015 Commercial Products Catalog 197

27 Steel Switch Boxes 2 3 /4 DEEP GANGABLE 14.0 CUBIC INCH CAPACITY 2 WIDE x 3 LONG FOR CONDUIT NO CLAMPS TP672, TP674 (TP676 1 screw ear), (TP678 2 screw ears) TP680, TP677 Bracket Ears Each End Each Side TP /2 1 /2 1 / TP /4 3 /4 1 / TP676 - Yes 1 /2 1 /2 1 / TP678 - Yes 3 /4 3 /4 1 / TP680 S, Set 5 /8-1 /2 1 /2, 1 Side 1 / TP677 S, Set 5 /8-3 /4 3 /4, 1 Side 1 / /2 DEEP GANGABLE 18.0 CUBIC INCH CAPACITY 2 WIDE x 3 LONG FOR NON-METALLIC CABLE CLAMPS IN EACH END TP236 TP238 TP239 TP240 TP242 TP243 Bracket Ground Pigtail Ears Each End Each Side TP /2 1 /2 1 / TP Yes 1 /2 1 /2 1 / TP239 - Yes Yes 1 /2 1 /2 1 / TP240 F, Set 1 / /2 1 /2 1 / TP242 S, Set 7 / /2 1 /2 1 / TP243 S, Set 7 /8 Yes - 1 /2 1 /2 1 / US: CAN: Copyright 2015 Commercial Products Catalog

28 Steel Switch Boxes 3 1 /2 DEEP GANGABLE 18.0 CUBIC INCH CAPACITY 2 WIDE x 3 LONG FOR ARMOURED & METAL-CLAD (MCI) CABLE CLAMPS IN EACH END Bracket TP244 TP249 TP246 Ground Pigtail Ears *UL approved for use with aluminum interlocking grounding metal-clad cable, Type MCIA (Southwire MCAP ). MCAP is a registered trademark of Southwire Company. Each End Each Side TP244* - - Yes 1 /2 1 /2 1 / TP249* - Yes Yes 1 /2 1 /2 1 / TP246* S, Set 7 / /2 1 /2 1 / /2 DEEP GANGABLE 18.0 CUBIC INCH CAPACITY 2 WIDE x 3 LONG FOR CONDUIT NO CLAMPS Bracket Ears TP248, TP250 TP252 TP254 Each End Each Side TP /2 1 /2 1 / TP /4 3 /4 1 / TP252 - Yes 1 /2 1 /2 1 / TP254 - Yes 3 /4 3 /4 1 / /2 DEEP SWITCH & MASONRY BOX EXTENSION RING TP /2 Deep Switch & Masonry Box Extension Ring TP422 1 /2 1 /2 + 3 /4 E For use as extension with switch box, not four square box. See page 181 for 4 steel square covers. US: CAN: Copyright 2015 Commercial Products Catalog 199

29 Steel Gang Boxes GANG BOXES 1 5 /8 DEEP x 4 1 /2 HIGH 1 /2 & 3 /4 KOs TP629 TP630 TP640 Gang Cubic Inches Width Each End Each Side TP /16 1 /2 3 /4 1 /2 3 /4 1 /2 3 / TP /8 1 /2 3 /4 1 /2 3 /4 1 /2 3 / TP /16 1 /2 3 /4 1 /2 3 /4 1 /2 3 / TP /4 1 /2 3 /4 1 /2 3 /4 1 /2 3 / TP /16 1 /2 3 /4 1 /2 3 /4 1 /2 3 / GANG BOXES 2 1 /2 DEEP x 4 1 /2 HIGH 3 /4 & 1 KOs Gang Cubic Inches TP871 Width TP873 Each End Each Side TP /16 3 /4 3 /4 1 /2 3 / TP /8 3 /4 3 /4 1 /2 3 / TP /16 3 /4 3 /4 1 /2 3 / TP /4 3 /4 3 /4 1 /2 3 / TP /16 3 /4 3 /4 1 /2 3 / GANG BOX PARTITIONS TP876 TP877 TP876 For 1 5 /8 Deep Box TP877 For 2 1 /2 Deep Box US: CAN: Copyright 2015 Commercial Products Catalog

30 Steel Gang Box Covers GANG BOX COVERS RAISED 13 /16 FOR PLASTER TP653 TP667 AMR3 Gang Length Capacity Cu. In. TP TP / AMR3** 3 3 /4-1 1 /2 Raised Adjustable TP / TP / TP / **ETL listed. CSA certified. GANG BOX COVERS, FLAT, BLANK TP803 TP806 Gang Length TP TP / TP / TP / TP / US: CAN: Copyright 2015 Commercial Products Catalog 201

31 Steel Masonry Boxes MASONRY BOXES 2 1 /2 DEEP x 3 3 /4 HIGH 1 /2 & 3 /4 CONCENTRIC KOs Gang Width MASONRY BOXES 3 1 /2 DEEP x 3 3 /4 HIGH 1 /2 & 3 /4 CONCENTRIC KOs TP682 Each End Each Side Capacity Cu. In. TP / TP / TP / TP / TP / TP TP690 Gang Width Each End Each Side Capacity Cu. In. TP / TP / TP / TP / TP / TP TP691 MASONRY BOX PARTITIONS & EXTENSION RING Masonry Box Partitions TP820 TP820 Non-metallic Partition for 2 1 /2 Deep Masonry Boxes 25 3 TP821 Non-metallic Partition for 3 1 /2 Deep Masonry Boxes 25 4 For use as extension with switch box, not four square box. See page 181 for 4 steel square covers US: CAN: Copyright 2015 Commercial Products Catalog TP /2 Deep Switch & Masonry Box Extension Ring TP422 1 /2 1 /2 + 3 /4 E

32 Steel Masonry Boxes GANGABLE MASONRY BOXES Features: box from a single gang box by simply removing the combo head screw holding the side with a #2 bit and connecting the two (or more) boxes together re-using the screws easily without tools in multi-gang boxes and are used to separate power and control circuits within the same box, as required by the National Electrical Code Width Each End Each Side Capacity Cu. In. 2 1 /2 Deep x 3 3 /4 High, 1 /2 & 3 /4 Concentric KOs TP / /2 Deep x 3 3 /4 High, 1 /2 & 3 /4 Concentric KOs TP / GANGABLE MASONRY BOX PARTITIONS TP654 TP654 Non-metallic Partition for 2 1 /2 Deep Gangable Masonry Boxes 25 4 TP656 Non-metallic Partition for 3 1 /2 Deep Gangable Masonry Boxes US: CAN: Copyright 2015 Commercial Products Catalog 203

33 Steel Octagon Boxes & Ceiling Pans 3 1 /4 ROUND CEILING PANS 4.0 CUBIC INCH CAPACITY 1 /2 DEEP CLAMPS IN BOTTOM FIXTURE RATED TP266 Cable Conduit TP266 1 / Weight limit for 3 1 /4 and 4 Octagon Outlet Boxes and Ceiling Pans is 50 lbs. for fixture/luminaire. Not suitable for fans. 3 1 /4 OCTAGON OUTLET BOXES 9.0 CUBIC INCH CAPACITY 1 1 /2 DEEP FIXTURE RATED TP256 TP258 TP259 TP260 TP264 For Conduit No Clamps TP256-1 /2 1 / TP258 Extension Ring 1 / For Non-metallic Cable with Clamps TP259 S Bracket, Set 1 /2 1 /2 1 / TP260-1 /2 1 / TP264 Two Screw Ears 1 /2 1 / Weight limit for 3 1 /4 and 4 Octagon Outlet Boxes and Ceiling Pans is 50 lbs. for fixture/luminaire. Not suitable for fans. 3 1 /4 ROUND CEILING COVERS TP270 TP272 Cable TP270 Flat Blank TP272 Flat, 1 /2 KO in Center US: CAN: Copyright 2015 Commercial Products Catalog

34 Steel Octagon Boxes & Ceiling Pans 4 ROUND CEILING PANS* 6.0 CUBIC INCH CAPACITY 1 /2 DEEP FIXTURE RATED TP269 TP267 TP269 KOs Only - 1 / TP267 KOs and Clamps - 1 / *Weight limit for 3 1 /4 and 4 Octagon Outlet Boxes and Ceiling Pans is 50 lbs. for fixture. Not suitable for fans. 4 OCTAGON OUTLET BOXES 15.5 CUBIC INCH CAPACITY 1 1 /2 DEEP FOR CONDUIT NO CLAMPS FIXTURE RATED TP274, TP278, TP834* TP276 TP273 TP280 TP282 TP284, TP286 TP274-1 /2 1 / TP273 Blank 1 / TP276-3 /4 1 /2 3 / TP278-1 /2 3 /4 1 /2 3 / TP280 C Bracket 1 /2 1 / TP282 S Bracket, Set 1 /2 1 /2 1 / Air Plenum TP834* For Air Plenum 1 /2 1 / Octagon Extension Rings (Slot & Key Permit Mounting without Removing Box Screws) TP284-1 / TP286-1 /2 3 / *For Air Plenum (no mounting holes) - not UL Listed. Weight limit for 3 1 /4 and 4 Octagon Outlet Boxes and Ceiling Pans is 50 lbs. for fixture/luminaire. Not suitable for fans. CSA certified. US: CAN: Copyright 2015 Commercial Products Catalog 205

35 Steel Octagon Boxes & Ceiling Pans 4 OCTAGON OUTLET BOXES 15.5 CUBIC INCH CAPACITY 1 1 /2 DEEP FOR ARMOURED & METAL-CLAD (MCI) CABLE CLAMPS IN EACH END FIXTURE RATED TP310 TP312 TP314 TP310* - 1 /2 1 / TP312* C Bracket 1 /2 1 / TP314* S Bracket, Set 1 /2 1 /2 1 / *UL approved for use with aluminum interlocking grounding metal-clad cable, Type MCIA (Southwire MCAP ). MCAP is a registered trademark of Southwire Company. Weight limit for 3 1 /4 and 4 Octagon Outlet Boxes and Ceiling Pans is 50 lbs. for fixture/luminaire. Not suitable for fans. 4 OCTAGON OUTLET BOXES 15.5 CUBIC INCH CAPACITY 1 1 /2 DEEP FOR NON-METALLIC CABLE WITH CLAMPS FIXTURE RATED TP298 TP300 TP302 TP304 TP306 TP308 TP298-1 /2 1 / TP300 With Side Nail Holes 1 /2 1 / TP302 C Bracket 1 /2 1 / TP304 S Bracket, Set 1 /2 1 /2 1 / TP306 Two Screw Ears 1 /2 1 / TP308 F Bracket, Set 1 /2 1 /2 1 / Weight limit for 3 1 /4 and 4 Octagon Outlet Boxes and Ceiling Pans is 50 lbs. for fixture/luminaire. Not suitable for fans US: CAN: Copyright 2015 Commercial Products Catalog

36 Steel Octagon Boxes & Ceiling Pans 4 OCTAGON OUTLET BOXES 21.5 CUBIC INCH CAPACITY 2 1 /8 DEEP FOR CONDUIT NO CLAMPS FIXTURE RATED TP288, TP290, TP294 TP292, TP838* TP292RED TP339 TP288-1 /2 1 /2 3 / TP288PF - 1 /2 1 /2 3 / TP290-3 /4 1 /2 3 / TP290PF - 3 /4 1 /2 3 / TP292-1 /2 3 /4 1 /2 3 / TP292PF - 1 /2 3 /4 1 /2 3 / TP292RED - 1 /2 3 /4 1 /2 3 / TP294-1 /2 3 / TP339 Blank 1 / Air Plenum TP838* For Air Plenum 1 /2 3 /4 1 /2 3 / *For Air Plenum (no mounting holes) - not UL Listed. Weight limit for 3 1 /4 and 4 Octagon Outlet Boxes and Ceiling Pans is 50 lbs. for fixture/luminaire. Not suitable for fans. TP catalog numbers ending in PF include ground screw with pigtail lead. 4 OCTAGON OUTLET BOXES 21.5 CUBIC INCH CAPACITY 2 1 /8 DEEP WITH CABLE CLAMPS FIXTURE RATED TP316 TP318 TP320 TP317 TP338 For Non-metallic Cable TP316-1 /2 1 / TP318 C Bracket 1 /2 1 / TP320 S Bracket, Set 1 /2 1 /2 1 / For Armoured & Metal-clad (MCI) Cable Clamps in Each End TP317* - 1 /2 1 / TP338* S Bracket, Set 1 /2 1 /2 1 / TP338PF S Bracket, Set 1 /2 1 /2 1 / *UL approved for use with aluminum interlocking grounding metal-clad cable, Type MCIA (Southwire MCAP ). MCAP is a registered trademark of Southwire Company. Weight limit for 3 1 /4 and 4 Octagon Outlet Boxes and Ceiling Pans is 50 lbs. for fixture/luminaire. Not suitable for fans. TP catalog numbers ending in PF include ground screw with pigtail lead. US: CAN: Copyright 2015 Commercial Products Catalog 207

37 Steel Octagon Covers & Accessories 4 OCTAGON BOX & ADJUSTABLE BAR SETS 15.5 CUBIC INCH CAPACITY 1 1 /2 DEEP BOX SETS FIXTURE RATED Weight limits: 50 lbs. at 16. TP372 TP377 TP367 Stud Spacing Stud For Conduit No Clamps TP372* 16 Yes For Non-metallic Cable with Clamps TP For Armoured & Metal-clad (MCI) Cable Clamps in Each End TP TP367PF *4 Octagon Box and Adjustable Bar Sets have 1 /2 KOs for conduit. TP catalog numbers ending in PF include ground screw with pigtail lead. ADJUSTABLE BAR HANGERS Features: TP356 TP352 Stud Spacing Fan Rated 16 Fan Weight (Lbs.) 24 Fan Weight (Lbs.) Fixture Rated 16 Fixture Weight (Lbs.) 24 Fixture Weight (Lbs.) TP No - - Yes TP Yes 70 - Yes US: CAN: Copyright 2015 Commercial Products Catalog

38 Steel Octagon Covers & Accessories 4 OCTAGON BOX COVERS CUBIC CAPACITY (SEE BELOW) TP322, TP853* TP323 TP326, TP331, TP332, TP333 TP328 TP329 TP335 TP334 TP336 FLEXIBLE FIXTURE HANGERS TPRFH Flexible Fixture Hangers are used in commercial or light industrial applications where HID high bay and low bay lighting fixtures are used. Specific applications include storage facilities, shipping warehouses, retail and DIY facilities. Features: 1 /2 or 3 /4 fixture conduit stems, these hangers allow the conduit stem of the fixture (luminaire) to swing in any direction; maximum swing angle is 26 from vertical max. slope angles 22 1 /2 3 /4 conduit stem as standard and come supplied with a 3 /4 1 /2 reducer for 1 /2 conduit stem applications Certifications and Compliances: Capacity Cu. In. TP322 Flat Blank, Octagon Shape TP322RED Flat Blank, Octagon Shape TP323 Flat Blank, Round Shape TP333 Raised 1, Open with Ears 2 3 / TP332 Raised 1 /2, Open with Ears 2 3 / TP326 Raised 5 /8, Open with Ears 2 3 / TP331 Raised 3 /4, Open with Ears 2 3 / TP328 Flat with 1 /2 KO, Octagon Shape TP329 Flat with 1 /2 KO, Round Shape TP335 Flat, for Toggle Switch TP334 Flat, Single Receptacle 1 13 / TP336 Flat, for Duplex Receptacle Air Plenum TP853* Flat, Blank with PVC Gasket *For Air Plenum (no mounting holes). CSA certified. Not UL Listed. Standard Materials and Finishes: TPRFH12 For use with 4 Round or Octagon Boxes Support Wt. (Lbs.) 50 US: CAN: Copyright 2015 Commercial Products Catalog 209

39 Steel Specialty Boxes LAMPHOLDERS Applications: Standard Material: discoloring and reduces breakage TP16099 Lampholder, Keyless, Feed Through OCTAGON CONCRETE BOXES & HUNG CEILING BOXES* TP620, TP622, TP628 TP635, TP636, TP644 TP623, TP624 (Bars Not Included) Depth Capacity Cu. In. TP620* 2 1 /2 and 3 /4 Single Row TP622* 2 1 /2 1 /2 and 3 /4 Single Row TP628* 3 1 /2 and 3 /4 Single Row TP and 3 /4 Single Row TP635* 3 1 /2 1 /2 Double Row TP636* 3 1 /2 1 /2 and 3 /4 Double Row TP /2 1 and 3 /4 Double Row TP and 3 /4 Double Row TP644* 4 1 /2 and 3 /4 Double Row Hung Ceiling Boxes (with TP650 Cover; Bars Not Included) TP623* 3 1 /2 1 /2 Double Row TP624* 3 1 /2 1 /2 and 3 /4 Double Row *Weight limit for 4 Octagon Concrete Boxes is 50 lbs. Not suitable for fans. Not UL Listed US: CAN: Copyright 2015 Commercial Products Catalog

40 Steel Specialty Boxes 4 FAN RATED OCTAGON CONCRETE BOX Applications: TP643 condominiums and restaurants with outdoor dining areas ceiling fans mounted to these boxes; because of the additional mounting support boss, this new box is suitable for use with fans of up to 70 pounds and fixtures up to 90 pounds Features: 1. The TP643 Fan Rated Concrete Box is made from two-piece welded construction and is supplied with two rows of 1 /2 and 3 /4 dedicated KOs 2. The box is also supplied with two external mounting ears which are used to secure the box to the forms 3. The fan (or fixture) is held securely in place by the two x 1 1 /2 long pan head screws and lock washers; the screws attach to the specially designed boss 4. There are two 8-32 x 1 /2 screws provided for attachment of a box plate/cover (TP648, TP649 or TP650 ordered separately) 5. Mounting support boss and locknuts allow the TP643 box to be used with fans of up to 70 pounds and fixtures up to 90 pounds Capacity Depth Cu. In. TP /2 and 3 / CONCRETE BOX PLATES TP648 TP649 TP650 TP652 TP648 1 /2 3 /4 KOs TP649 Flat, Blank TP650 3 /8 1 /2 3 /4 KOs TP652 Single Receptacle US: CAN: Copyright 2015 Commercial Products Catalog 211

41 Ceiling Fan Boxes & Supports CEILING FAN BOXES & SUPPORTS CUBIC INCH CAPACITY (SEE BELOW) Weight limits: TP lbs. max. for fans; 50 lbs. max. for fixture. TP301 Fan is supported independent of outlet box. Mounting screws go through box and into joist. Box will support fans up to 70 lbs. and fixtures up to 90 lbs. TP lbs. max. for fans; 90 lbs. max. for fixtures. TP275 TP261 TP301 TP315 TP379 TP352 Stud Spacing TP275 TP315 TP379 TP261 TP301* 1 1 /2 Deep, Clamps and Mounting Screws (Polybagged) 1 1 /2 Deep Octagon, Fan Box with New Work Bar Hanger 1 1 /2 Deep with Fan Brace Old Work Bar Hanger 5 /8 Deep with External Clamp and Mounting Screws (Polybagged) 1 /2 Deep, 4 Round, with NM Snap-in Connector, Mtg. Screws, Protective Cover (No Bag) Capacity Cu. In Weight Limits (Lbs.) Fans Fixtures 1 /2 1 / /2 1 / /2 1 / / / * 90* *TP301 Fan is supported independent of outlet box. TP315 comes with Romex clamp installed on one side. The other three sides have a 1 /2 KO, a bagged MC clamp and screw, and a bagged plastic NM connector. ADJUSTABLE BAR HANGERS 16 Fan Weight (Lbs.) 24 Fan Weight (Lbs.) 16 Fixture Weight (Lbs.) 24 Fixture Weight (Lbs.) Stud Fan Fixture Spacing Rated Rated TP Yes 70 - Yes US: CAN: Copyright 2015 Commercial Products Catalog

42 Ceiling Fan Boxes & Supports CEILING FAN BOXES PVC Weight limits: fans and fixtures are supported independent of outlet box. Mounting screws go through box and into joist. Box will support up to 70 lbs. for fans and 90 lbs. for fixtures. Provided with Romex connector. TP1300 Capacity Cu. In. Integral Clamp TP /16 Dia., 1 /2 Deep Pan Section, 4 Deep Overall with Mtg. Hardware and External Clamp, Protective Cover / NON-METALLIC CEILING FAN BOXES 2 3 /16 DEEP With clamps for non-metallic cable. All mounting hardware supplied; suitable for support of fans weighing up to 35 lbs. Features: time required to mechanically secure the wire to the box TP16511 Mounting Capacity No. of Clamp Diameter Method Cu. In. Openings TP Nails Only US: CAN: Copyright 2015 Commercial Products Catalog 213

43 Steel Box Accessories GROUNDING SCREW & PIGTAIL TP711 TP701 TP704 Std. Pkg. TP701 Grounding Screw with 8 Insulated No. 12 Stranded Wire TP711 Grounding Screw with 8 Insulated No. 12 Copper Wire TP704 #10-32 x 3 /8 Grounding Screw TP704BULK #10-32 x 3 /8 Grounding Screws in Jar LOW PROFILE MOUNTING & DRILLING & TAPPING SCREWS TP704BULK GROUNDING CLIP TP710 Low Profile Screws Reduces Risk of Sheetrock Bulge STS8BULK TP710 #8 x 1 /2 L.P. Screws STS8BULK #8 x 1 /2 Self-tapping Screw Jar TP706 Std. Pkg. TP706 For Grounding Switch and Outlet Boxes Using Non-metallic Sheathed Cables No. 14 and No. 12, with Grounding Wire OLD WORK CLIP TP651 Std. Pkg. TP651 Clips Lock Old Work Steel Switch Boxes Tightly to Wall; Two Required Per Box 250 Sets 25 Sets 4 REPLACEMENT PARTS TP900 TP901 TP902 TP900 MC-BX Clamp with Screws TP901 One Screw Mounting Ear with Screws TP902 Two Screw Mounting Ear with Screws US: CAN: Copyright 2015 Commercial Products Catalog

44 Steel Box Accessories HOLD-IT SWITCH BOX SUPPORTS FIG. 1 FIG. 2 FIG. 3 TP708 Two Metal Holders for Mounting Old Work Switch Boxes in All Types of Wall Materials 500 Sets 5 SWITCH BOX EXTENSIONS TP709* *Not UL Listed. TP709 Fits Snugly Inside All 3 x 2 Width Boxes; Maximum Adjustable Depth 0.78 ; Furnished with Mounting Screws Capacity Cu. In STEEL STUD SAFETY PLATES Features: TP659 2 x 3 1 /8 Steel Plate BACK TO BACK BOX CONNECTORS ZINC DIE CAST Applications: Size / US: CAN: Copyright 2015 Commercial Products Catalog 215

45 Steel Square Boxes 4 SQUARE OUTLET BOXES & COVERS Applications: Features: Certifications and Compliances: 4 SQUARE OUTLET BOXES 22.0 CUBIC INCH CAPACITY (WELDED) 21.0 CUBIC INCH CAPACITY (DRAWN) 1 1 /2 DEEP FOR CONDUIT CSA LISTED Steel Boxes TP404G TP425G TP414G Metal Stud Sizes Bracket TP404G 1 /2 1 /2 3 / 1 /2 1 /2 3 / TP425G "VP" 1 /2 1 /2 3 / 1 /2 1 /2 3 / 82 TP423G 1 /2 1 /2 3 / 1 /2 1 /2 3 / 81 TP414G 1 /2 3 / 1 /2 3 / US: CAN: Copyright 2015 Commercial Products Catalog

46 Steel Square Boxes 4 SQUARE OUTLET BOXES 22.0 CUBIC INCH CAPACITY 1 1 /2 DEEP FOR NON-METALLIC CABLE CLAMPS IN EACH END CSA LISTED TP449G Bracket TP449G 1 /2 1 /2 3 / 1 /2 4 SQUARE OUTLET BOXES 22.0 CUBIC INCH CAPACITY 1 1 /2 DEEP FOR ARMOURED & METAL-CLAD (MCI) CABLE & HCF CABLE CLAMPS IN EACH END CSA LISTED TP454G Bracket TP454G* 1 /2 1 /2 3 / 1 /2 81 Steel Boxes US: CAN: Copyright 2015 Commercial Products Catalog

47 Steel Square Boxes 4 SQUARE OUTLET BOXES 30.3 CUBIC INCH CAPACITY 2 1 /8 DEEP FOR CONDUIT CSA LISTED TP403G/TP403PFG TP432G TP434G TP438G TP451G Steel Boxes Bracket TP403G 1 /2 1 /2 3 / 1 /2 1 /2 3 / TP403PFG 1 /2 1 /2 3 / 1 /2 1 /2 3 / TP432G 3 / 1 /2 1 /2 3 / TP436G 1 /2 1 /2 3 / TP434G 1 /2 3 / 1 /2 3 / TP438G 1 /2 1 /2 3 / 1 /2 3 / TP451G 1 /2 1 /2 3 / 1 /2 1 /2 3 / US: CAN: Copyright 2015 Commercial Products Catalog

48 Steel Square Boxes & Covers 4 SQUARE OUTLET BOXES 30.3 CUBIC INCH CAPACITY 2 1 /8 DEEP FOR ARMOURED & METAL-CLAD (MCI) CABLE & HCF CABLE CLAMPS IN EACH END CSA LISTED TP431G TP440G Metal Stud Sizes Bracket TP431G* 1 /2 1 /2 3 / 1 /2 TP440G* 1 /2 1 /2 3 / 1 /2 4 SQUARE EXTENSION RINGS 1 1 /2 DEEP WITH CONDUIT KNOCKOUTS 21.0 CUBIC INCH CAPACITY 2 1 /8 DEEP WITH CONDUIT KNOCKOUTS 30.3 CUBIC INCH CAPACITY CSA LISTED Steel Boxes TP422 TP443 (2 1 /8 Deep) 1 1 /2 Deep Switch & Masonry Box Extension Ring TP422 1 /2 1 /2 3 / 2 1 /8 Deep TP443 1 /2 3 / 66 TP465 US: CAN: Copyright 2015 Commercial Products Catalog

49 Steel Square Covers COVERS FOR 4 SQUARE BOXES CUBIC INCH CAPACITY (SEE BELOW) CSA LISTED #8-32 Screw Used on Covers TP472 TP474 TP478 TP487 TP473, TP475, TP476, TP477, TP479, TP483 TP TP474 3 / 21 TP478 1 /2 31 TP487 3 / TP473 1 / 3 / 23 TP476 1 /2 3 / 26 TP477 /8 3 / TP475 3 / 3 / 31 TP479 3 / TP483 1 / 3 / Capacity Cu. In. MUD RINGS FOR 4 SQUARE STEEL OUTLET BOXES CSA LISTED Steel Boxes TP480 TP482, TP484, TP486, TP489 TP494 TP488, TP490 TP496, TP499, TP500, TP501, TP502 Capacity Cu. In. One Device TP480 TP482 1 / 21 TP484 1 /2 23 TP489 /8 26 TP486 3 / TP488 TP / Two Device TP TP496 1 / 13 TP498 1 /2 18 TP499 /8 22 TP500 3 / TP / 31 TP502 US: CAN: Copyright 2015 Commercial Products Catalog

50 Steel Square Covers 4 SQUARE SURFACE COVERS 5.5 CUBIC INCH CAPACITY RAISED 1 /2 CSA LISTED TP503 TP504 TP506 TP508 TP510 TP512 TP507, TP514, TP519 TP516 TP509 (4 Screws), TP513 TP511 TP515 TP517 TP518 (2 Screws) TP503 TP /32 31 TP TP508 TP TP512 TP507 1 /32 TP /32 TP /32 TP TP509 2 /16 23 TP518 2 / TP TP TP TP Steel Boxes US: CAN: Copyright 2015 Commercial Products Catalog 221

51 Steel Square Covers TILE WALL COVERS FOR 4 SQUARE BOXES CUBIC INCH CAPACITY (SEE BELOW) CSA LISTED TP524 TP534 TP540 Applications: Features: Capacity Cu. In. One Device TP520 1 /2 TP522 3 / 36 TP524 TP / TP /2 TP Two Device Steel Boxes TP532 1 /2 TP534 3 / TP TP / TP /2 TP US: CAN: Copyright 2015 Commercial Products Catalog

52 Steel Square Boxes 4 11 /16 SQUARE OUTLET BOXES & COVERS Applications: Features: 1 /2 3 / Certifications and Compliances: 4 11 /16 SQUARE OUTLET BOXES 29.5 CUBIC INCH CAPACITY 1 1 /2 DEEP WITH CONDUIT KOs CSA LISTED TP548G TP549G Steel Boxes TP548G 1 /2 3 / 1 /2 3 / TP549G 1 /2 1 /2 3 / 1 /2 3 / US: CAN: Copyright 2015 Commercial Products Catalog 223

53 Steel Square Boxes & Covers 4 11 /16 SQUARE OUTLET BOXES 42.0 & 44.0 CUBIC INCH CAPACITY 2 1 /8 DEEP WITH CONDUIT KOs CSA LISTED TP563G TP554G TP556G TP558G TP560G Bracket 42.0 Cubic Inch Capacity TP563G 1 /2 1 /2 3 / 1 /2 3 / TP554G 3 / 1 /2 3 / TP556G 1 /2 3 / 1 /2 3 / TP558G 3 / 1 /2 3 / TP560G 1 /2 3 / 4 11 /16 SQUARE EXTENSION RINGS 1 1 /2 DEEP WITH CONDUIT KOs 29.5 CUBIC INCH CAPACITY 2 1 /8 DEEP WITH CONDUIT KOs 42.0 CUBIC INCH CAPACITY CSA LISTED Steel Boxes TP550 TP /2 Deep 29.5 Cubic Inch Capacity TP550 1 /2 3 / /8 Deep 42.0 Cubic Inch Capacity TP564 1 /2 3 / US: CAN: Copyright 2015 Commercial Products Catalog

54 Steel Square Covers 4 11 /16 SQUARE COVERS CUBIC INCH CAPACITY (SEE BELOW) CSA LISTED TP568 TP572 TP574 - TP582, TP529, TP531 TP584, TP586, TP589, TP593, TP541, TP543 Flat and Raised Capacity Cu. In. TP568 TP572 1 /2 One Device TP574 1 / 32 TP576 1 /2 36 TP578 3 / TP579 /8 TP580 TP / TP /2 TP531 Two Device TP TP583 1 / 26 TP584 1 /2 TP587 /8 32 TP586 3 / TP TP / TP /2 63 TP543 Steel Boxes US: CAN: Copyright 2015 Commercial Products Catalog

55 Steel Square Covers 4 11 /16 SQUARE SURFACE COVERS 9.0 CUBIC INCH CAPACITY 1 /2 RAISED CSA LISTED TP720 TP722 TP724, TP730, TP736 TP726 TP728 TP732 TP734 TP738 TP740 Steel Boxes TP720 TP722 TP /32 TP730 TP736 TP726 TP728 TP732 TP734 TP738 TP740 TP US: CAN: Copyright 2015 Commercial Products Catalog

56 Steel Utility Boxes & Covers UTILITY BOXES CUBIC INCH CAPACITY (SEE BELOW) 4 LONG x 2 1 /8 WIDE CSA LISTED TP588G TP594G, TP596G TP604G, TP606G Bracket 1 1 /2 Deep 10.3 Cubic Inch Capacity TP588G 1 /2 1 /2 1 7 /8 Deep 13.0 Cubic Inch Capacity TP594G 1 /2 1 /2 TP596G 3 / 1 /2 2 1 /8 Deep 14.5 Cubic Inch Capacity TP604G 1 /2 1 /2 TP606G 3 / 1 /2 UTILITY BOX COVERS CSA LISTED Steel Boxes TP608 TP610 TP612 TP613 TP614 TP616 TP618 TP608 TP610 /32 TP /32 TP613 TP614 1 /2 TP616 8 TP618 US: CAN: Copyright 2015 Commercial Products Catalog

57 Steel Switch Boxes 1 1 /2 DEEP NON-GANGABLE 7.5 CUBIC INCH CAPACITY 2 WIDE x 3 LONG CSA LISTED TP100G Bracket Ears Each End Each Side For Non-metallic Cable Clamps in Each End TP100G 1 /2 2 DEEP GANGABLE 10.0 CUBIC INCH CAPACITY 2 WIDE x 3 LONG CSA LISTED Steel Boxes TP130G TP132G TP131G Hold-Tite Bracket Ears Each End Each Side For Conduit No Clamps, Flush Device TP130G 1 /2 1 /2 1 /2 TP132G /8 1 /2 1 /2 1 /2 TP131G 1 /2 1 / US: CAN: Copyright 2015 Commercial Products Catalog

58 Steel Switch Boxes 2 1 /4 DEEP GANGABLE BEVELED CORNERS 10.5 CUBIC INCH CAPACITY 2 WIDE x 3 LONG CSA LISTED TP137G Hold-Tite TP138G Ears Bumps Clamp Screws Through Beveled Corners Each End Each Side TP137G 1 /2 TP138G 1 /2 2 1 /2 DEEP GANGABLE 12.5 CUBIC INCH CAPACITY 2 WIDE x 3 LONG CSA LISTED TP162G TP163G TP164G, TP168G TP161G TP171G Steel Boxes Bracket Ears For Non-metallic Cable Clamps in Each End Ground Pigtail Leveling Bumps Each End Each Side TP161G 1 /2 TP162G 1 /2 1 /2 62 TP163G 1 /2 TP164G 1 /2 1 /2 1 /2 1 /2 TP168G 1 / 1 /2 1 /2 1 /2 TP171G 1 /2 1 /2 1 /2 1 /2 US: CAN: Copyright 2015 Commercial Products Catalog

59 Steel Switch Boxes 2 1 /2 DEEP GANGABLE 12.5 CUBIC INCH CAPACITY 2 WIDE x 3 LONG FOR ARMOURED & METAL-CLAD (MCI) CABLE CLAMPS IN EACH END CSA LISTED TP180G TP185G Bracket Ears Each End Each Side TP180G* 1 /2 1 /2 1 /2 1 /2 TP185G* 1 /2 1 /2 1 /2 1 /2 2 1 /2 DEEP GANGABLE 12.5 CUBIC INCH CAPACITY 2 WIDE x 3 LONG FOR CONDUIT NO CLAMPS CSA LISTED Steel Boxes TP214G TP218G TP222G Bracket Ears Leveling Bumps Each End Each Side TP214G 1 /2 1 /2 TP218G 1 /2 1 /2 1 /2 TP222G /8 1 /2 1 /2 1 /2 US: CAN: Copyright 2015 Commercial Products Catalog

60 Steel Switch Boxes 3 1 /2 DEEP GANGABLE 18.0 CUBIC INCH CAPACITY 2 WIDE x 3 LONG FOR NON-METALLIC CABLE CLAMPS IN EACH END CSA LISTED TP238G TP242G Bracket Ground Pigtail Ears Each End Each Side TP238G 1 /2 1 /2 1 /2 TP242G /8 1 /2 1 /2 1 /2 3 1 /2 DEEP GANGABLE 18.0 CUBIC INCH CAPACITY 2 WIDE x 3 LONG FOR CONDUIT NO CLAMPS CSA LISTED TP254G Bracket Ears Each End Each Side TP254G 3 / 3 / 1 /2 Steel Boxes 1 1 /2 DEEP SWITCH & MASONRY BOX EXTENSION RING TP /2 Deep Switch & Masonry Box Extension Ring TP422 1 /2 1 /2 3 / US: CAN: Copyright 2015 Commercial Products Catalog 231

61 Steel Octagon Boxes & Ceiling Pans 4 ROUND CEILING PANS* 6.0 CUBIC INCH CAPACITY 1 /2 DEEP FIXTURE RATED CSA LISTED TP269G TP269G 1 /2 1 / 4 OCTAGON OUTLET BOXES 15.5 CUBIC INCH CAPACITY 1 1 /2 DEEP FOR CONDUIT NO CLAMPS FIXTURE RATED CSA LISTED Steel Boxes TP274G, TP278G TP276G TP280G TP282G TP284, TP286 TP274G 1 /2 1 /2 TP276G 3 / 1 /2 3 / TP278G 1 /2 3 / 1 /2 3 / TP280G 1 /2 1 /2 TP282G 1 /2 1 /2 1 /2 Octagon Extension Rings (Slot & Key Permit Mounting without Removing Box Screws) TP284 1 /2 36 TP286 1 /2 3 / 36 1 / US: CAN: Copyright 2015 Commercial Products Catalog

62 Steel Octagon Boxes & Ceiling Pans 4 OCTAGON OUTLET BOXES 15.5 CUBIC INCH CAPACITY 1 1 /2 DEEP FOR ARMOURED & METAL-CLAD (MCI) CABLE CLAMPS IN EACH END FIXTURE RATED CSA LISTED TP310G TP312G TP310G* 1 /2 1 /2 TP312G* 1 /2 1 / / 4 OCTAGON OUTLET BOXES 15.5 CUBIC INCH CAPACITY 1 1 /2 DEEP FOR NON-METALLIC CABLE WITH CLAMPS FIXTURE RATED CSA LISTED Steel Boxes TP300G TP302G TP300G 1 /2 1 /2 TP302G 1 /2 1 /2 1 / US: CAN: Copyright 2015 Commercial Products Catalog 233

63 Steel Octagon Boxes & Ceiling Pans 4 OCTAGON OUTLET BOXES 21.5 CUBIC INCH CAPACITY 2 1 /8 DEEP FOR CONDUIT NO CLAMPS FIXTURE RATED CSA LISTED TP288G, TP290G, TP294G TP292G TP288G 1 /2 1 /2 3 / TP290G 3 / 1 /2 3 / TP292G 1 /2 3 / 1 /2 3 / TP294G 1 /2 3 / 1 / 4 OCTAGON OUTLET BOXES 21.5 CUBIC INCH CAPACITY 2 1 /8 DEEP WITH CABLE CLAMPS FIXTURE RATED CSA LISTED Steel Boxes TP318G For Non-metallic Cable TP318G 1 /2 1 / / US: CAN: Copyright 2015 Commercial Products Catalog

64 PVC Switch Boxes Applications: Non-metallic Switch and Outlet Boxes are used: Features: Certifications and Compliances: Standard Materials: SWITCH BOXES ANGLED NAILS TP1800 TP2000 TP2300 Bracket or Nails SWITCH BOXES INTEGRAL CLAMPS Capacity Cu. In. H W D TP1800 Nails 3 3 /4 2 /4 2 3 /4 23 TP2000 Nails 3 3 /4 2 /4 3 3 / 25 TP2300 Nails 3 3 /4 2 /4 3 7 / 27 PVC Boxes TP1690 (Old Work) TP2030 (For Wood or Metal Studs) Bracket or Nails Capacity Cu. In. H W D TP / 2 5 / 2 3 /4 TP2030 /2 3 / 2 /4 3 3 / 24 US: CAN: Copyright 2015 Commercial Products Catalog 235

65 PVC Switch Boxes 3 DEEP SWITCH BOXES TWO GANG TP3490 (Old Work) TP3600 TP3635 Bracket or Nails /2 Capacity Cu. In. H W D TP / / TP3600 Nails 3 3 / TP3635* 3 3 / /16 DEEP SWITCH BOXES THREE GANG TP4600 TP4635 Bracket or Nails Capacity Cu. In. TP4600 Nails 45 TP4635* 25 /2 PVC Boxes 2 11 /16 DEEP SWITCH BOXES FOUR GANG TP6180 Bracket or Capacity Nails Cu. In. TP US: CAN: Copyright 2015 Commercial Products Catalog

66 PVC Switch Boxes LOW VOLTAGE PARTITION TWO, THREE OR FOUR GANG PVC TP1000, TP1001 Use with the Following Boxes TP TP PVC Boxes US: CAN: Copyright 2015 Commercial Products Catalog 237

67 PVC Switch Boxes & Covers 4 SQUARE WITH INTEGRAL CLAMPS 18.0 CUBIC INCH CAPACITY 1 5 /8 DEEP TP1900 Capacity Bracket Cu. In. TP1900 Yes 75 4 SQUARE PVC DEVICE COVERS TP1013 TP1023 Raised Capacity Cu. In. TP1013 /2 TP1023 /2 PVC Boxes US: CAN: Copyright 2015 Commercial Products Catalog

68 Ceiling Boxes 3 1 /2 NON-METALLIC CEILING BOXES PVC 2 7 /8 DEEP Weight limit: 50 lbs. for fixture except where indicated. TP16200, (TP /8 Deep) Old Work TP16201 TP16311 Clamps Ground Plate Bracket/ Bar Hanger Capacity Cu. In. No. of Clamp Openings TP16200 Yes - Snap TP16201 Yes Yes Snap TP16311* Yes Yes Nails *Nail bracket is set 1 9 /16 back from the face of the box. Weight limit is 6 lbs. for wall mounted fixtures only. Ceiling Boxes US: CAN: Copyright 2015 Commercial Products Catalog 239

69 Ceiling Boxes 4 NON-METALLIC CEILING BOXES PVC 2 1 /4 DEEP Weight limit: 50 lbs. for fixture except where indicated. TP16111, TP16110 TP16122, TP16123 Clamps Ground Plate Bracket/ Bar Hanger Capacity Cu. In. No. of Cable Pry-outs TP16111 Yes - Nails TP16110 Yes Yes Nails TP16122 Yes TP16123 Yes Yes NON-METALLIC CEILING FAN BOXES 2 3 /16 DEEP With clamps for non-metallic cable. All mounting hardware supplied; suitable for support of fans weighing up to 35 lbs. Features: TP16511 Ceiling Boxes Mounting Capacity No. of Clamp Diameter Method Cu. In. Openings TP US: CAN: Copyright 2015 Commercial Products Catalog