1005 & Issue 11/ From Serial Number From Serial Number 3501

Transcription

1 1005 & 1010 Instruction Book & Parts List Issue 11/ From Serial Number From Serial Number 3501

2 1. READ THE INSTRUCTION BOOK THOROUGHLY before attempting to operate or carry out any maintenance on the machine. If you do not understand any part of this manual, ask your dealer for assistance. 2. ALWAYS CARRY OUT SAFE MAINTENANCE. Never clean, adjust or maintain the machine until the engine has been stopped, the machine come to rest, the PTO disengaged and the key removed. SAFETY FIRST! 3. NEVER WORK UNDER A MACHINE RAISED ON THE 3-POINT LINKAGE unless it is securely supported. 4. NEVER OPERATE THE MACHINE WITH ANY PARTS OR GUARDS MISSING. Check that all guards including the PTO shaft guards are in good condition and in place before operating the machine. 5 OPERATE SAFELY. Before starting work, check that there are no persons or animals in the immediate vicinity of the machine or tractor. Always maintain full control of the tractor and machine. Ensure that you know how to stop the tractor and machine quickly in case of emergency. 6. SECURE THE PTO GUARD BY MEANS OF CHECK CHAINS to suitable points on the tractor and machine to prevent the outer plastic shield from rotating. 7. NEVER STAND BETWEEN THE MACHINE AND THE TRACTOR WHEELS. 8. DO NOT WEAR LOOSE OR RAGGED CLOTHING 9. BEWARE OF DUST. Under dusty conditions, keep the cab windows and doors closed. The use of a dust mask conforming to EN149 is strongly recommended. 10. BEWARE OF HIGH NOISE LEVELS. Some tractor/implement combinations give noise levels in excess of 90dB at the operator's ear. Under such circumstances, ear defenders should be worn. Keep cab windows and doors closed to reduce noise level. Throughout this handbook, the term `tractor' is used to refer to the power source used to drive the machine. It does not necessarily refer to a conventional agricultural tractor. HEALTH AND SAFETY AT WORK Our equipment is designed so as to conform with current Health & Safety Regulations and therefore poses no significant hazard to health when properly used. Nevertheless, in the interests of all concerned, it is essential that equipment of our manufacture is used in accordance with the instructions that are supplied or are available from our Technical Staff. Legislation requires that all operators are instructed in the safe operation, cleaning and maintenance of equipment and machines. This handbook forms part of that instruction and it must be read and understood before fitting the machine onto the tractor or attempting to use it. Your supplier is responsible for carrying out any necessary pre-delivery inspection, fitting the machine onto the tractor and test running. The supplier must also give instruction in the safe use, maintenance and adjustment of the machine. In the interests of safety, please ensure that the instructions referred to above are brought to the attention of all your employees who are to use the equipment. We recommend that the use of this equipment is restricted to capable trained operatives. Persons under the age of sixteen should not operate the machine and should be kept away from where it is being used. WARRANTY The standard warranty is for 12 calendar months against faulty materials and workmanship. Components supplied as part of the original machine, but manufactured by another company, e.g. PTO shafts, wheels etc., are subject to the original manufacturer's conditions and warranty. Where repairs are carried out under warranty:- a) Claims for the fitting of non original parts will not be considered unless prior agreement has been obtained. b) The repairer must be advised that the work is to be the subject of a warranty claim beforehand. c) Any claim must be submitted within four weeks of the repair. d) The damaged parts must be retained for inspection and returned carriage paid if required. The right to withdraw warranty is reserved if:- a) Non-original parts are fitted. b) The machine has been abused, badly maintained or used for purposes other than that for which it was designed.

3 INSTRUCTIONS INDEX Page SECTION 1 Specifications 2 2 Explanation of pictograms 3 3 Safety 4 4 Left and right hand 4 5 Use of the Tomahawk 4 6 Use on the public highway 4 7 Preparation of the machine 4 8 Preparation of the tractor 5 9 Fitting the machine onto the tractor 5 10 Operating Instructions - Loading including use of the bale lift 5 11 Operating Instructions -Discharge 7 12 Machine safety protection 8 13 Maintenance 8 14 Optional extras Storage Disposal 10 FAULT FINDING CHARTS SECTION 17 Chart 1 11 Chart 2 12 PARTS LISTS SECTION 18 Tailgate ram 13 Chute ram 13 Braked axle 14 Chassis 15 Front housing & rotor 16 Drawbars 17 Sloping flange giraffe chute & housing 18 Right hand outlet chute & housing 20 Bed chain drive 21 Floor Assembly 22 Unbraked axle Single crossbeater & drive Twin crossbeater & drive crossbeater unit & body panels 28 Decals 29 Body 30 Bale lift (export market only) 32 Solenoid/ valve 33 Lights 34 Electric controls 35 Hydraulic hoses 36 Pressure line filter 37 Comer PTO shaft - Combined slip and overrun clutch 38 Comer PTO shaft Wide angle C.V. joint 39 Wiring Diagram Lights 40

4 1. SPECIFICATIONS Specifications Right hand chute Sloping Swivel Chute Model Number of crossbeaters Bale chamber (W x H x L) m 1.7m x 1.01m x 3.46m 1.7m x 1.58m x 3.46m Side discharge Height - Barrier 1.95 m 2.00 m 2.40 m 2.45 m Giraffe discharge height - Max N/A 2.95 m 3.00 m Giraffe rotation angle N/A 280 degrees Overall width (All chutes closed) 2.44 m 2.52 m 2.31 m 2.42 m Overall width (Side chute raised) 3.18 m 3.27 m N/A Overall width (Giraffe chute open) N/A 2.44 m 2.46 m Overall height - maximum 2.76 m 2.93 m 3.44 m 3.49 m Overall height - minimum 2.52 m 2.93 m 2.80 m 2.93 m Overall length (Tailgate up) 6.17m 6.17m 6.17m 6.17m Overall length (Tailgate down & extended) 8.04 m 8.04 m 8.04 m 8.04 m Max Round bale diameter 2.0m 2.0m 2.0m 2.0m Maximum Rectangular Bale Size 1.3m x 1.2m x 2.5m 1.3m x 1.2m x 2.5m Tyre size (Standard tyres) 285/70 R /55 R /70 R /55 R22.5 Wheel track (Standard Tyres) 1.9m 2.0m 1.9m 2.0m Weight 3290 kg 3510 Kg 3370 Kg 3590 Kg Volume of clamp silage 8.0 m m m m 3 Max. Hydraulic Oil Pressure Max. Hydraulic Oil Flow Min. Hydraulic Oil Flow 220 bar 60 litres/minute 30 litres/minute Maximum Drawbar Load 650 Kg 600 Kg 650 Kg 600 Kg Minimum Tractor Size 60kW (80hp) 66kW (90hp) 60kW (80hp) 66kW (90hp) Sound power level 95 dba 86dbA 95 dba 86dbA 2

5 2. EXPLANATION OF PICTOGRAMS Bed Chain Speed Power On Light Raise Giraffe Chute Deflector Rotate Giraffe Clockwise Rotate Giraffe Anti-clockwise ON Long Chop OFF Short Chop Raise RH Chute Raise Tailgate Lower Tailgate Lower RH Chute Lower Giraffe Chute Deflector Bed Chain Forward Light Bed Chain Forward Bed Chain Reverse High rotor speed Giraffe Chute Selector RH Chute Selector Standard chute ram selected Allow rotor to stop before removing blockage with tool provided Low rotor speed Giraffe chute ram selected Please read instruction book before using the ma- Direction of rotation & frequency of PTO input Shaft 540 DL1012 Beware thrown objects Keep your distance Beware crushing hazard Keep clear Tighten wheel nuts to setting in operators handbook Blockage removal tool Maximum hydraulic circuit pressure 3 Do not allow any one to ride on machine

6 3. SAFETY In addition to the standard safety guidelines listed at the beginning of this handbook, the following special safety items apply to the Tomahawk. 3.1 The machine shall be operated by one person only. 3.2 NEVER put your hands inside the delivery chutes. In the event of a blockage clear it using the tool provided (stored at the front of the machine). First, stop the engine, remove the key, disengage the PTO and wait for the rotor to come to rest. 3.3 NEVER enter the bale chamber unless the engine has been stopped the key removed, the PTO disengaged and the rotor come to rest. 3.4 NEVER insert anything inside the chute or bale chamber while the machine is running. 3.5 DANGER. When entering or leaving the bale chamber take care, the tailgate surface may be slippery. 3.6 Beware of overhead power lines when the swivel chute deflectors are fully raised, contact with power lines could result in the operator receiving an electric shock. 3.7 Do not climb onto the top edges of the bale chamber whilst the machine is use. 3.8 Do not allow anyone to ride on the machine or tractor linkage or drawbar. 3.9 Do not allow persons or animals to stand in front of the outlet chutes whilst the machine is running Do not operate the tailgate if any person or animal is standing in the loading area behind the machine and always ensure good rearward visibility when lowering the tailgate Never put your hand over a hydraulic leak. Oil under pressure may enter the blood stream The shredding of dusty or mouldy material can create dust which may have adverse health effects. Operator exposure to such conditions should be avoided where possible. When circumstances prevent this, either use a tractor with a suitable forced air cab filtration system or an adequate respirator. Respirators must comply with the relevant Standard and be approved by the Safety Inspectorate. Disposable filtering face piece respirators to EN149 or half mask respirators to EN140 fitted with filters to EN 143 are likely to be adequate When rotating the chute always check the clearance between the chute and the rear of the cab, particularly the window if it is open Before disconnecting the hydraulic hoses always lower the tailgate onto the ground for safety and to avoid residual pressure in the hoses Always fit the correct size tyre onto the rims when fitting replacements Care must be taken when handling large bales since they have sufficient weight and density to cause serious injury or death. For this reason never attempt to manually load bales from the stack above the machine. Large bales should be handled with appropriate machinery either directly into the Tomahawk or into a position where they can be self loaded. 4. LEFT AND RIGHT HAND In this Handbook and Parts List, the terms Left and Right Hand apply to the machine when viewed looking towards the rear of the tractor. 5. USE OF THE TOMAHAWK 1005/1010 Each machine can be used to shred the materials as recommended in table 1 below. Material Baled Silage Yes No Baled Hay Yes Yes Baled Straw Yes Yes Clamp Silage Yes Yes Table 1. Recommended Materials Its use for shredding other materials is not recommended without first seeking further advice from Teagle Machinery Ltd. The machine must never be run with any of the chute components removed or modified. The machine may then become in breach of safety standards which are there for your safety. 6. USE ON THE PUBLIC HIGHWAY 6.1 United Kingdom It is necessary to fit a road lighting kit to comply with highways regulations. Suitable lighting kits are available from Teagle Machinery Ltd through your local Teagle dealer/ distributor The Tomahawk is classed as a trailed implement and requires brakes when used on the public highway, the maximum speed limit of 20mph for tractors and trailed appliances must be observed. 6.2 Export Countries Please contact the relevant government department to ensure local regulations are complied with. Failure to comply with road traffic legislation may lead to prosecution by local law enforcement agencies and could also result in a road traffic accident. 7. PREPARATION OF THE MACHINE Remove the PTO shaft and any other loose items from the body of the machine. 4

7 8. PREPARATION OF THE TRACTOR For good visibility down both sides of the machine when working and reversing, the tractor should be fitted with mirrors. The PTO power required to drive the Tomahawk is typically about 60KW (80HP) for the 1005 and 67.5 KW (90HP) for the However, the suitability of any particular tractor will depend upon, a) the distance over which the straw is to be spread, b) the type of bale to be spread, and c) whether the machine is to be used to transport bales along the road. The machine is designed to use the standard 540 rpm PTO shaft. The hydraulic valve block requires a double acting spool valve or a single acting valve with an unrestricted return. Whichever is used, the hydraulic supply must be independent of the 3-point linkage. Where the machine is to be operated on a tractor with closed centre hydraulics, a closed centre plug Part No. HYD5342 must be fitted to the valve. This can be obtained from Teagle Machinery Ltd. and includes the necessary instructions for fitting. The control box mounting bracket should be fitted inside the cab so that the controls are conveniently situated for the operator. It should be remembered that structural members of the cab must not be drilled or welded. The electric control supply cable should be connected the tractor s auxiliary 3 pin socket. Should a socket not be available then the control box must be wired directly to the battery. Remove the connector plug to reveal the brown and blue wires, brown is positive, blue is negative. Wire directly to the battery with a suitable lead and insulated connectors. Under no circumstances remove the fuse holder or use fuses with a higher rating than 7.5amps. Warranty will be invalidated The red LED illuminates only when the fuse has blown. This typically indicates that the incorrect polarity has been applied. Check for correct polarity, replace fuse and connect again. If the problem persists contact Teagle Machinery Ltd. for advice. 9. FITTING THE MACHINE ONTO THE TRACTOR Check that the lower links are at a height such that they do not foul the PTO shaft when the tractor is turning. If they are not used regularly, it is recommended that they be removed. Hitch the machine to the tractor via the drawbar without the PTO shaft fitted. Release the parking brake on the right hand side of the machine by pulling forwards and then allow to swing rearwards. Park the tractor and machine securely on level ground and remove the key. It is essential to get the relationship between the tractor PTO shaft and the gearbox input shaft correct to give a satisfactory PTO shaft life. The correct geometry exists when the machine is horizontal. If the machine is shredding whilst turning on a regular basis it is recommended that a PTO shaft with a wide angle, constant velocity joint be fitted. A shaft of this type can be obtained from the manufacturer. 5 The PTO shaft will require cutting to length to suit the tractor to remove the risk of bottoming resulting in catastrophic failure of the machine gearbox. Proceed as follows: 1.) Measure the distance between the annular groove on the tractor output shaft to the annular groove on the machine input shaft. 2.) Measure approximately the distance between the retaining balls of each sliding yoke at either end of the PTO shaft with it fully collapsed. 3.) Subtract the second measurement from the first and now subtract this value from 150mm (6 ). The answer is the amount to be removed from each half of the PTO shaft. 4.) Separate the 2 halves of the PTO shaft and remove the necessary amount from each half guard and each half tube. Remove the guards to facilitate cutting if required. 5.) Fit the slip clutch side of the PTO shaft to the machine and the other end to the tractor, the PTO shaft should now have the required 150mm (6 ) travel before bottoming. This should be indicated by the length of black PTO guard showing. 6.) Gradually turn the tractor until maximum turning lock is achieved checking that the PTO shaft does not come to within 100 mm (4 inches) of bottoming. 7.) Drive the tractor and machine over any significant undulating ground conditions checking that the PTO shaft does not come to within 100 mm (4 inches) of bottoming. Connect the hydraulic hoses into the spool valve of the tractor. It is important that the supply hose to the valve is connected to the pressure port of the tractor, this hose is marked with red tape around the hose. Attach the brake hose to the tractor brake coupling Once the control box has been positioned, route the machine cable into the cab making sure it is kept away from the rear wheel and any pinch points between the PTO shaft and link arms. Where possible, route into the cab through cable entry points on the tractor, allowing the rear window to be kept closed during use. Plug the cable connector into the socket on the box and lock by the clamp provided. Ensure the functions of the control box are completely understood before proceeding to use the machine. In particular the bed chain is actuated in the forward direction by pushing the forward direction button and stopped by pressing the button again. Reverse of the bed chain can only be actuated by holding the reverse button. 10. OPERATING INSTRUCTIONS - LOADING 10.1 General The strings or net should be removed from the bale as it is being loaded into the machine. The Tomahawk will shred some string but some will tend to wrap around the crossbeater(s). Putting twine or netwrap through the machine is not recommended as it will be eventually spread on the land and polluting subsequent crops. When removing string or netwrap from bales never climb into the bale chamber or onto the tailgate behind a bale unless the PTO has been disengaged, the

8 engine has been stopped, the key removed and the machine come to rest. Bales can be loaded into the machine in two ways, using a loader or by self-loading using the machine tailgate. If a loader is used, simply load the bale into the bale chamber such that it is fully inserted, but do not ram it against the crossbeater(s). When loading the machine, it will be necessary to run the bed chain to help self load the bale into the chamber. However, excessive use of the bed chain for this purpose may cause material to enter the rotor housing resulting in a blockage during machine start up. The tailgate is designed to load bales into the chamber of the machine. Where a telescopic tailgate is fitted, it is important to only self load with it in the retracted position. To retract the tailgate: 1.) Lower the tailgate until it is horizontal. 2.) Switch off the tractor and remove the key. 3.) Remove the 2 retaining bolts as indicated figure 1. 4.) Slide the rear tailgate section towards the machine, replace the retaining bolts in the retracted position. raising the tailgate further. With the bale on the tailgate cut the strings or netwrap on the machine side of the bale as low as possible and remove around the top of the bale. Rope hooks are positioned on the underside of the tailgate to tie partially removed twine and netwrap to. Raise the tailgate, the bale will roll into the machine leaving the twine or netwrap tied to the tailgate allowing easy removal Multiple Bale Loads The Tomahawk 1005/1010 are large machines designed to carry several bales in a load. To maximise the carrying capacity of the machine it is recommended that the telescopic tailgate be extended as per Figure 1. A suitable mechanical loader should now be used for loading. The machine is now capable of handling two large rectangular bales 1.2x1.3x2.7m or three 2m round bales as shown in figure 2 below. Figure 1. Telescopic Tailgate Setting 10.2 Self Loading Make sure the drawbar is securely attached to the tractor as self loading may cause it to lift. For large rectangular bales, place the bale on the ground with one end against a solid object. For easy removal of the strings place the bale on its side so that the strings are not in contact with the ground. In the case of quadrant bales, place the bale with the knots on the top. Reverse the machine with the tailgate lowered until the bale slides up the tailgate into the bale chamber. Raise the tailgate until it is horizontal and engage the bed chain to move the bale fully onto the tailgate. Make sure that the bale is not forced against the crossbeater(s) as this may cause problems when starting the machine. Before removing the strings, place the posts in the sockets on the tailgate and put the chain around the rear of the bale to avoid the risk of crushing from unsecured material. To load round bales, reverse the machine under the bale so that the bale rests against the tailgate. Lift the tailgate slightly and drive forward a short distance before 6 Figure 2. Tomahawk T1000/T1010 Loaded 10.4 Bale Lift In certain territories (not UK) the machines are available with a bale lift in the body of the machine to permit a portion of the load to be lifted from the bed chain. This can be advantageous in reducing the amount of material presented to the crossbeater(s) ensuring smooth discharge. Operation of the bale lift is by means of the chute selection buttons on the bottom left of the control box. When fitted, the feature should be used as shown in figure 3 below. Figure 3. Bale Lift Use

9 10.5 Clamp Silage When loading clamp silage, lower the tailgate slightly to give a larger body capacity. The hydraulic oil pressure required to rotate the bed chain will be determined by the quantity of silage loaded. The machine requires operating pressures of 120 bar (1750 psi.) when the body is filled with clamp silage. 11. OPERATING INSTRUCTIONS - DISCHARGE 11.1 Gearbox Speed Selection The machine is fitted with a 2-speed gearbox. For blockage free operation it is important that the correct gearbox speed is selected for the material being discharged as per table 2 below. The gearbox has a neutral position, so make sure the required gear has been properly selected so as not to block the rotor housing. Material Distance Spread Gearbox Speed PTO Speed Straw Maximum High 540 Straw Close High 300 Baled Silage Close Low 540 Clamp Silage Close Low 300 Table 2. Recommended Rotor Speed For shredding straw and other dry materials either rotor speed may be used, for maximum throw distance the handle should be moved towards the position marked by the hare to give a 1:1 ratio between PTO and discharge rotor speed. For shredding silage and other wet materials it is recommended that the slow rotor speed be used since long throw distances are not usually required To set the slow rotor speed, the gearbox handle should be moved to the position marked by the tortoise to give a 1.85:1 ratio. The machine may be used at reduced PTO speeds and still deliver material to the desired position. Very low PTO speeds should be avoided as a blockage in the rotor housing may result Right Hand Chute Adjust the position of the chute to deliver the material being spread in the desired location, typically this will be down beside the machine for feeding and elevated for bedding Sloping Swivel Chute The swivel chute rotates through 300 degrees and can be operated to either side of and behind the machine. To deliver silage close to the machine position the chute so that material is delivered onto the feed passage slide, the position of the slide can be adjusted to deliver the material accurately. Alternatively the position of the material can be controlled by the chute, it may be necessary to rotate the chute fully delivering material alongside the drawbar. The discharge of baled silage along the left hand side of the machine is not recommended. In transport, rotate the chute to the right hand side of the machine aligning the indicators on the chute and 7 top housing. Fully lower the deflector to keep the width and height of the machine to a minimum Engaging PTO Engage the PTO with the tractor engine on low idle and increase the speed rapidly to working speed when the clutch has engaged fully Before Commencing Discharge If the machine is loaded to capacity, i.e. material other than clamp silage is supported by the tailgate, the tailgate must remain horizontal until the material in the body has been discharged. This is necessary to allow the material within the body of the machine to rotate freely once it comes into contact with the crossbeater(s). No attempt should ever be made to force material towards the crossbeater(s) using the tailgate. With the bed chain speed control on the control box on zero, engage the tractor spool valve and switch the bed chain on in the forward direction by pressing the bed chain forward button once. General discharging instructions follow after the specific round/square bale and clamp silage instructions below Discharging Square Bales Gradually increase bed chain speed by means of the speed control until shredding commences. It is then advisable to increase bed chain speed to a point at which the slices of the bale being shredded are forced up and over the material coming forward. This rotational motion is represented in figure 4 below. Figure 4. Rotation Of Square Bales Where a bale lift is fitted, release the portion of the bale retained only when the first portion has been discharged which is usually indicated by a large fall in discharge rate. Once the material in the bale chamber has been discharged the tailgate can be lifted to allow the second bale (or a portion of) to be loaded into the chamber. It will be found advantageous to only allow half of the second bale to enter the chamber at a time thus allowing room for each half to rotate. Typically the rate of discharge may be controlled by bed chain speed but only once rotation of the material within the body of the machine has been achieved in the first instance Discharging Round Bales Gradually increase bed chain speed by means of the speed control until discharge commences. Good performance will only be achieved by getting the bale to rotate within the chamber as shown in figure 5 overleaf. Increasing the speed of the bed chain will increase the rate of discharge until a maximum rate is achieved. If the bed chain speed is too great, material will unroll from the bale at a rate greater than can be discharged. This will

10 be indicated by a build up of material above the bale restraint. Figure 5. Rotation Of Round Bales 11.8 Discharging Clamp Silage Increase bed chain speed until the desired discharge rate is achieved. Once the forward portion of the load has been discharged, the tailgate can be lifted to ensure a continuous feed rate General Discharging Instructions If a large amount of loose material builds up above the bale restraint it may be necessary to reverse the bed chain until the loose material falls down behind the crossbeater before commencing discharge. When it is necessary to stop shredding part way through a bale, always stop the bed chain rotation and put it in reverse for a few seconds before stopping the rotor and crossbeater(s). This allows the material in the area around the crossbeater(s) and rotor to be blown clear of the machine. Failure to do this may result in a blockage occurring when the machine is re-started. The length of chop will vary with the condition of the bale. The evenness of feed and power consumption will also vary with the material being shredded. In general, baled silage and damp or caked straw materials will require a higher power input than dry brittle materials. Should the rotor or crossbeater(s) become blocked indicated by either slipping of the PTO clutch or failure of the crossbeater(s) shear bolt, it may be necessary to turn the rotor backwards. This may be achieved by levering the rotor paddles with a post through the outlet chute. Further access may be gained by removing the blockage panels from the front of the upper and lower rotor housing. 12. MACHINE PROTECTION DEVICES IMPORTANT: The machine is fitted with a shear bolt on the cross beater drive line. After a blockage, the bolt may need replacing. If the bolt has failed grease must be applied to the slipping surfaces via the grease nipple before the shear bolt is replaced. IMPORTANT: The machine is fitted with a slip clutch on the PTO shaft. If this slips repeatedly, it should not be tightened until the machine has been examined to check that there is no fault or blockage. Refer to 'Maintenance' for the correct clutch setting. The slip clutch may be hot. Care should be taken when removing it from either the machine or tractor. 13. MAINTENANCE 13.1 Safety Never climb into the bale chamber or onto the tailgate unless the PTO has been disengaged. The engine has been stopped, the key has been removed and the machine has come to a rest. Care must be taken when carrying out any maintenance on / around the chopping blades as they are extremely sharp. Leather gloves will give some protection against minor cuts Blades When carrying out maintenance work on the blades enter the bale chamber via the tailgate. Wedge the rotor and crossbeater(s) to prevent them from turning reducing the risk of trapping hands between the knives and bale restraint fingers. When replacing knives use spanners with long handles which will allow the bolts to be removed whilst avoiding contact with the sharp edges of the knives. Always keep your hands away from the edges of blades - particularly new ones, as they are extremely sharp. The blades have a sharp trailing edge, which remains sharp even when the leading edge is blunt Bed Chain To tension the bed chain, release the front lock nut on the tensioner and jack the tensioner using the other nut. The bed chain should be tensioned such that the chain can be lifted 50mm above the bed midway between the drive sprockets. Retighten lock nuts after tensioning. The chain tension must be checked and adjusted after initial use as bedding in shall occur. The position of the rear sprocket scrapers must now be altered. To adjust them, slacken the nut on the outside of the body, slide it towards the idler until it touches the back it off approximately 2mm and retighten the nut. If the bed chain becomes tight in use, check that the grooves in the sprockets have not packed tight with straw or silage. Adjust the sprocket scrapers so that they run tightly against the bottoms of the grooves in the centre of the sprockets as shown in figure 6 below. Figure 6. Sprocket Scraper Position If the area beneath the bed chain becomes blocked or requires attention, remove the clips to allow the rear underfloor inspection panel to swing down. Clear any blockage and replace panel Crossbeater shear bolt To replace the shear bolt, open the hinged LH drive chain guard. The shear bolt is on the lower crossbeater shaft. Grease the hub before replacing the shear bolt with a Grade 10.9 M8 x 50 bolt. 8

11 13.5 Gearbox After 50 hours of use the gear box oil should be drained and replaced with new oil. To drain the oil, remove the PTO shaft and guard cone remove the drain and filler plugs and allow it to empty. Waste oil should be collected and disposed of at an oil recycling facility Refill the gearbox to the level plug with SAE90.EP gearbox oil. The oil capacity of the gearbox is 4.7ltrs 13.6 Drive Chains Apply chain lubricant or oil weekly. The chains should be tensioned so that there is 12-13mm (1/2 ) deflection at the mid span point as indicated in figure 7 below. Figure 7. Chain Deflection To tension the crossbeater(s) drive chain(s), open the hinged chain guard on the left hand side of the machine. For the lower beater drive, slacken the layshaft bearing bolts and tensioner locknut. Increase tension by jacking the bearing as required until the correct tension condition is met. Retighten all nuts. For the upper crossbeater slacken the tensioner roller mounting bolt in the centre of the roller and turn the tension screw on the adjuster clockwise until the correct tension condition is met. Retighten the roller mounting bolt Swivel Chute The chute is rotated by means of a gear and ring gear. It is important that this is well greased. To apply grease to the ring gears there are 4 grease nipples on the mounting flange. The deflector ram has 2 grease nipples, one on each pivot bush Hydraulics Before attempting to dismantle any of the hydraulic system, the tailgate and deflectors must be fully lowered to prevent injury from the unexpected lowering of these components. The hydraulic system is protected from contamination by an inline pressure filter. Periodically the element should be checked for contamination and it is recommended that the element be replaced at least once annually. To replace the element, remove the guard covering the hydraulic valve on the front right of the machine and unscrew the filter canister. Replace element, retighten canister and fit valve guard. If problems are experienced with either the hydraulic system or electric controls, please contact Teagle Machinery Ltd. for advice as a separate manual is available to cover troubleshooting and repair PTO Slip Clutch If the clutch slips repeatedly for no apparent reason there are a number of things to be checked: Firstly check that the clutch linings do not show signs of damage or excessive wear. If so, they should be replaced. When new they are 3mm. (1/8") thick. Also make sure that the compressed spring length is set to give the correct torque setting see PTO shaft parts list. If the clutch continues to slip it should be adjusted as follows: 1 Remove the guard fitted to the rotor gearbox. 2 Fit the PTO shaft with the slip clutch at the machine end. 3 Insert a piece of wood through the discharge chute and position it such that it prevents the rotor from turning. 4 Insert a steel bar through the rear PTO yoke and use a spring balance to obtain the correct torque setting. The clutch should just slip at a torque of 1200 Nm. (900 lb.ft.) - equal to a force of 1000N. at 1.2 metre (225 lb. at 4 feet) from the centre of the yoke. Adjust the clutch as necessary using the eight spring loaded clamp bolts Lubrication Good quality semi-solid grease should be applied to the following grease points: Weekly Swivel chute ring gear (4 nipples) PTO shaft joints - (2 nipples) PTO guard bearings (where fitted) PTO shaft sliding members Twice a week: Bed chain bearings (4 nipples) Crossbeater bearings (4 nipples) Gearbox output side shaft\drive (2 Nipples) Shearbolt sprocket bearing (1 nipple) Chute ram pivots (2 nipples) Ring hitch Oil Crossbeater roller chains The above lubrication frequencies are based on typical daily use for bedding & feeding purposes. Continuous use for special applications may require more frequent lubrication Wheel Nuts Before using a new machine and daily during use, check the wheel nuts are tight. They should be torqued to a value of 400Nm (320 lb ft). Once the nuts are allowed to work loose, it may be found impossible to keep them tight and new nuts and studs will be required to overcome the problem. In extreme cases, damage to the wheel rims and hubs may result Tyre Pressure Check the tyre pressures regularly inflating them to the pressures in table 3 overleaf as required. 9

12 Tyre Size Pressure bar (psi) 285/70R ( 84) 405/60 R ( 84 ) Table 3. Tyre Pressures Replacing Wheels If it is necessary to remove a wheel, place a jack underneath the axle beam, loosen the wheel nuts and raise the machine until the wheel can be removed. Place an axle stand underneath the machine before removing the wheel. Refit the wheel and tighten the wheel nuts Electric Controls. The electric controls require no maintenance and it is imperative that no part of the system is ever sprayed with a moisture repelling agent such as WD40. If a malfunction of the system occurs, please contact Teagle Machinery Ltd or an authorised dealer/distributor for advice Handbrake Adjustment With reference to figure 8 below, the handbrake can be adjusted by releasing the locknut (item 1) and increasing tension by means of the tension nut (item 2). If maximum travel is reached then the clamp (item 3) can be released and the rope adjusted accordingly. Figure 8. Handbrake Adjustment Service Brake Adjustment It is imperative that the brakes are adjusted correctly to meet the requirements of the current braking regulations. As the brake shoes wear, it may be necessary to realign the actuating rods on their splines so that the arms are perpendicular to the ram body Removal Of Main Rotor The rotor can only be released from the main gearbox with the application of service tool SC3776 available from the manufacturer. 14. OPTIONAL EXTRAS 14.1 Drawbar Jack Where the machine is fitted with a drawbar jack, adjust the height of the drawbar to match the height of the hitch point on the tractor. Reverse the tractor and attach the drawbar. Lower the machine until the weight is fully transferred to the tractor. Remove the pin retaining the jack to the drawbar and transfer it onto the transport position across the front of the chassis. 15. MACHINE STORAGE When the machine is not being used it is recommended that the control box be stored safely away from the machine in a dry location. The electrical connections together with hydraulic hoses should be stored in the positions provided on the layshaft guard on the front right of the machine. If the machine is to be laid up for any great length of time it should be thoroughly cleaned down and any bright surfaces treated with paint as opposed to a rust preventative since the machine is used for dispensing foodstuffs. All lubrication points should be attended to ready for subsequent reuse. 16. DISPOSAL At the end of the machine s working life, the method of disposal must be within the legislation laid down by the local authority or the National Environment Agency. The machine is composed of ferrous materials, synthetic paints and rubber compounds. NOTES 10

13 17. FAULT FINDING TOMAHAWK FAULT FINDING CHART PART 1 Symptom Fault Possible Solutions High power consumption Rotor will not start Bed chain will not turn Slow discharge Bale stops discharging Bale fed too quickly into crossbeater(s). Knives too agressive Bale forced against crossbeater(s). Material in rotor housing jamming rotor. Clutch setting too low. Hydraulic valve problem. Material jammed between bed chain and bodywork. Relief valve setting too low. Tractor hydraulic oil pressure low. Bed chain has come off the sprockets. Bed chain broken. Motor not turning. Bed drive chain has come off the sprocket. Sprockets seized. Bed Chain speed too slow. Insufficient aggression of knives Blades blunt or worn. Material jammed hard against bale restraint above crossbeater(s). Rotor speed low. Rotor speed low. Crossbeater(s) not rotating. Gearbox in neutral. Bed chain not rotating. Reduce bed chain speed. Slope knives backwards using holes provided Reverse bed chain. Reverse rotor to clear blockage. Check setting and adjust. See section below. Clear material and check bed chain tension. Adjust relief valve or replace if the spring is worn. Check pressure delivered by tractor. Check sprocket condition, replace the bed chain and tension it. Check sprocket groove is clean and that the chamber below the floor is free from obstructions. Repair chain and refit. Check connections and tractor hydraulics. If motor is seized reverse flow to release. Consult your dealer if this fails. Check sprocket condition, replace the chain and tension it. Replace bearings. Increase forward speed of bed chain using flow control valve. Check knives to see if they are in aggressive position on crossbeater(s) Sharpen, reverse or replace blades. Reverse bed chain direction for at least 5 seconds until feed is restored. Check that slip clutch is not slipping - indicated by hot clutch assembly. Check tractor tachometer. Replace shear bolt in drive sprocket. Remove material from rotor housing before restarting and select correct gear. See Above. 11

14 TOMAHAWK FAULT FINDING CHART PART 2 Symptom Fault Possible Solutions Shear bolt fails repeatedly. Single beater shear bolt fails repeatedly Twin beater shear bolt fails repeatedly Chute and rotor blocks Swivel giraffe chute blocks Hydraulic valve fails to operate Bolt bushes worn or damaged. Tailgate raised too high forcing bale into crossbeater(s). Front half of large rectangular bale not rotating freely. One or more bale restraint fingers bent and interfering with crossbeater. Long dry material wrapping around crossbeater(s) and bale restraint. Chute exit blocked. Rotor speed low. Material not flowing smoothly. Rotor speed low. Hydraulic connections to tractor faulty or not connected. Replace with new bushes. Lower the tailgate to allow material in bale chamber to rotate freely. Lower the tailgate to allow material in bale chamber to rotate freely and increase the bed chain speed to encourage rotation of the front half of bale. Straighten or replace damaged bale restraint finger. Consult manufacturer. Make sure material can leave the chute freely. Check that slip clutch is not slipping Select high rotor speed on gearbox Raise deflector to improve flow and rotate chute to achieve desired delivery position. Check high rotor speed selected on gearbox. Rectify making sure pressure is applied to the valve via the supply hose and that the return line flow is not restricted. Bed chain no longer operates or only very slowly. Failure may be sudden or intermittent. Dirt or contamination in the Bypass Valve or the Pressure Relief Valve in the flow control slice. Firstly, remove the Bypass Valve from the Flow Control Slice inspect for contamination clean and replace. If problem still exists, remove the Pressure Relief Valve and inspect for contamination. If problem persists or re occurs regularly replace tractor hydraulic oil with new clean oil. Loss of operation of rams and swivel slices. Also operation of bed in only 1 direction may occur. Failure may be sudden or deteriorate slowly over a few days. Oil leaking from between slices of the valve. Oil leaking from between slices of the valve. Failure of pilot cartridge through contamination Internal pressure in valve. Clamping bolts loose. Interface seals damaged by either of the above. See section below. Contact manufacturer for advice. Check return line hose connected and that return line flow is not restricted by damaged fittings or the tractor spool valve Check bolts through valve tightened to correct torque specified in the maintenance section. Replace damaged seals. 12

15 18. PARTS LISTS TAILGATE RAM (With Pilot Operated Check Valve) Closed centres 571, Open centres 971, Stroke 400 Ref. Description Part No. Qty. Ref. Description Part No. Qty. Ram assembly CYL Seal kit (items 1,10,11,13 & 14) HYD (Check valve seals not included, see item 16) 1 Wiper seal HYD Wiper seal housing CYL Rod seal back up ring DC Cylinder assembly CYL Piston rod CYL Piston body CYL Piston end CYL Restrictor 1.3mm HYD Locknut M20 FAS Seal HYD "O" ring HYD Rod seal housing CYL "O" ring HYD "U" packing HYD Pilot operated check valve CYL Check valve seal kit (not shown) HYD CHUTE RAM Closed centres 386, Open centres 642, Stroke 256. Ref. Description Part No. Qty. Ref. Description Part No. Qty. Ram assembly CYL Seal kit (items 4, 5, 8 & 10) HYD Piston CYL Cylinder body CYL Restrictor 0.8mm dia HYD Rod seal 25mm HYD Wiper seal 16mm HYD Piston rod CYL Wiper seal housing CYL "O" ring B.S. 216 HYD Rod seal housing CYL "O" ring B.S. 017 HYD Piston seal 40mm dia. HYD Grease Nipple ¼ BSF BRG

16 BRAKED AXLE Ref. Description Part No. Qty. Associated Components Part No. Qty. 1 Ratchet handbrake assembly SC Setscrew M10 x 25 FAS2654P 2 Plain washer M10 FAS2344P 2 Locknut M10 FAS Handbrake adjuster SC Bolt M12 x 40 FAS9680P 1 Rope Collar TRM Locknut M12 FAS Plain nut M10 FAS2303P 2 3 Handbrake cable SC Rope Grip 8mm ROP Brake equaliser SC Bolt M12 x 45 FAS9681P 1 Locknut M12 FAS Braked axle SC Bolt M20 x 140 FAS9742P 4 Plain washer M20 FAS2347P 4 Locknut M20 FAS Wheel 385/55 R Stud WE Wheel nut WE Mudguard RH SC Setscrew M12 x 45 FAS2681P 2 Setscrew M12 x 30 FAS2678P 2 Plain washer M12 FAS2345P 8 Locknut M12 FAS Cup Square M10 x 25 FAS9262P 2 Plain washer M12 FAS2345P 2 Locknut M10 FAS Mudguard LH SC Setscrew M12 x 45 FAS2681P 2 Setscrew M12 x 30 FAS2678P 2 Plain washer M12 FAS2345P 8 Locknut M12 FAS Cup Square M10 x 25 FAS9262P 2 Plain washer M12 FAS2345P 2 Locknut M10 FAS Brake cylinder TB Brake return spring SPR

17 CHASSIS Ref. Description Part No. Qty. Associated Components Part No. Qty. 1 Chassis SC Front Plate LH SC Setscrew M10 x 25 FAS2654P 1 Plain washer M10 FAS2344P 1 Locknut M10 FAS Sealing Strip SC Setscrew M10 x 25 FAS2654P 7 Locknut M10 FAS Clamp Plate SC Front Plate RH SC Setscrew M10 x 25 FAS2654P 1 Plain washer M10 FAS2344P 1 Locknut M10 FAS Front Lower Panel SC Setscrew M10 x 20 FAS2652P 5 Cup Square M10 x 25 FAS9262P 4 Plain washer M10 FAS2344P 9 Locknut M10 FAS Middle Lower Inspection Panel SC Setscrew M10 x 25 FAS2654P 12 Plain washer M10 FAS2344P 24 Locknut M10 FAS Chain Runner SC Setscrew M12 x 30 FAS2678P 8 Setscrew M12 x 45 FAS2681P 4 Plain Washer M12 FAS2345P 24 Plain Washer 38 x 13 x 5 FAS4801P 8 Locknut M12 FAS Rear Lower Inspection Panel SC Setscrew M10 x 25 FAS2654P 6 Plain Washer M10 FAS2344P 12 Locknut M10 FAS Hinged Inspection Panel SC Sealing Pin FAS Tailgate Ram CYL Tailgate Pivot Pin TRM Tailgate Ram Pin SC Spring Tension Pin FAS

18 FRONT HOUSING & ROTOR Ref. Description Part No. Q ty. Associated Components Part No. Q ty. Rotor c\w Paddles SC Item 1 & 2 1 Paddle (5 Bolt Fixing) SC Setscrew M12 x 30 FAS2678P 48 Locknut M12 FAS Rotor SC Setscrew M14 x 45 FAS2696P 1 Washer 75 x 15 x 10 FAS4805P 1 3 Front Housing SC Sprocket 14 Tooth (Silage) SC Key 10 x 8 x 40 FAS Sprocket 25 Tooth (Dual Chop) SC Setscrew M10 x 30 FAS2655P 1 Spring washer M10 FAS2354P 1 Washer 45 x 10 x 5 FAS2412P 1 5 Flange Bearing 1 3 / 8 BRG Grease Nipple M6 Straight BRG Setscrew M12 x 35 FAS2679P 2 Plain Washer M12 FAS2345P 2 Locknut M12 FAS Drive Adjustment Plate SC Setscrew M16 x 60 FAS2707P 1 Plain nut M16 FAS2305P 1 Locknut M12 FAS Layshaft - Splined Yoke SC End Yoke PTO Cross Journal Kit PTO Setscrew M12 x 80 FAS2688P 1 Plain Nut M12 FAS

19 Ref. Description Part No. Q ty. Associated Components Part No. Q ty. 8 Lower Access Panel SC Cup Square Bolt M8 x 20 FAS9241P 2 Plain Washer M8 FAS2343P 2 Locknut M8 FAS Gearbox - Splined Side Output SC Setscrew M14 x 25 FAS2699P 11 Shake Proof Washer M14 FAS Key 18 x 11 x 70 FAS Gear Selection Lever SC Bolt M8 x 16 FAS2625P 1 Plain Washer M8 FAS2343P 1 11 Gear Change Handle SC R Clip 2.5mm FAS6002P 1 12 Housing Threaded Plate SC Hose Carrier Bracket SC Setscrew M12 x 30 FAS2678P 2 Washer M12 FAS2345P 2 14 Hose Carrier (Pivoting) SC Setscrew M12 x 30 FAS2678P 4 Washer M12 FAS2345P 4 Locknut M12 FAS Strap Re-useable FAS Blockage Removal Tool SC DRAWBARS Ref Description Part No. Qty Associated Components Part No. Qty Clevis Hitch Drawbar Assembly SC Items 1, 2 & 5 1 Drawbar Beam SC Bolt M20 x 75 FAS9735P 6 Washer M20 FAS2347P 6 Locknut M20 FAS Drawbar Clevis SC Setscrew M12 x 35 FAS2679P 6 Washer M12 FAS2345P 12 Locknut M12 FAS Jack kit SC Items 3 & 4 3 Jack SC Pin FAS Lynch Pin FAS Jack Transport Socket SC Setscrew M12 x 30 FAS2678P 1 Washer M12 FAS2645P 1 Locknut M12 FAS PTO Rest SC Setscrew M8 x 25 FAS2629P 2 Washer M8 FAS2343P 4 Locknut M8 FAS Fixed Drawbar Assembly SC Items 5 & 6 6 Drawbar Beam SC Bolt M20 x 75 FAS9735P 6 Plain Washer M20 FAS2347P 6 Locknut M20 FAS

20 SLOPING FLANGE GIRAFFE CHUTE & HOUSING Ref. Description Part No. Qty. Associated Components Part No. Qty. Kit Complete SC End Deflector SC Setscrew M12 x 35 FAS2679P 2 Plain Washer M12 FAS2345P 2 Locknut M12 FAS Top Link SC Bolt M12 x 50 FAS9682P 2 Bolt M12 x 55 FAS9683P 2 Plain Washer M12 FAS2345P 4 Locknut M12 FAS Mid Deflector SC Lower Link LH SC Bolt M12 x 50 FAS9682P 2 Plain Washer M12 FAS2345P 2 Locknut M12 FAS Lower Link RH SC Bolt M12 x 50 FAS9682P 2 Plain Washer M12 FAS2345P 2 Locknut M12 FAS

21 Ref. Description Part No. Q ty. Associated Components Part No. Q ty. 6 Lower Deflector SC Setscrew M12 x 35 FAS2679P 2 Bolt M12 x 45 FAS9681P 2 Plain Washer M12 FAS2345P 4 Locknut M12 FAS Swivel Chute Base SC Chute Ram CYL Pivot Bush - Deflector SC Bolt M12 x 80 FAS9688P 1 Pivot Bush - Ram Body SC Bolt M12 x 90 FAS9690P 1 Plain Washer M12 FAS2345P 2 Locknut M12 FAS Housing Top - Inclined SC Grease Nipple 1/4" BSF BRG Setscrew M12 x 25 FAS2677P 6 Plain Washer M12 FAS2345P 12 Locknut M12 FAS Setscrew M10 x 25 FAS2654P 2 Cup Square Bolt M10 x 25 FAS9262P 3 Plain Washer M10 FAS2344P 7 Locknut M10 FAS Feed Passage Slide SC Setscrew M12 x 25 FAS2677P 3 Setscrew M12 x 30 FAS2678P 1 Plain Washer M12 FAS2345P 6 Locknut M12 FAS Upper Inspection Panel SC Plain Washer M8 FAS2343P 5 Locknut M8 FAS Strap Non Re-usable FAS Hose Clamp 1 / 4 " HYD Setscrew M8 x 35 FAS2631P 1 14 Side Inspection Panel SC Plain Washer M8 FAS2343P 6 Locknut M8 FAS Hydraulic motor c/w gear items 15,17&18 SC Hydraulic Motor 200cc 25mm Shaft HYD Setscrew M12 x 35 FAS2679P 2 Plain Washer M12 FAS2345P 2 Locknut M12 FAS Bonded Seal 1/2 BSP HYD / 2 x 1 / 4 M/M Union ( 1 / 4 Hosing ) HYD Key 8 x 7 x 30 FAS Seal Kit SAM Hydrauliks HYD Spacer 25mm SC Gear 25mm bore SC Setscrew M8 x 25 FAS2629P 1 Spring washer M8 FAS2353P 1 Plain Washer 30 x 9 x 5 FAS Spacer Segment - Small SC Spacer Segment - Large SC Clamp Segment SC Setscrew M10 x 35 FAS2656P 10 Locknut M10 FAS Drive Guard SC Setscrew M10 x 20 FAS2652P 1 Plain Washer M10 FAS2344P 1 19

22 RIGHT HAND CHUTE & HOUSING Ref Description Part No. Q ty Associated Components Part No. Q ty Standard Chute Kit Complete SC Deflector Strip SC Cup Square Bolt M8 x 20 FAS9241P 3 Plain Washer M8 FAS2343P 3 Locknut M8 FAS Deflector SC Bolt M12 x 55 FAS9683P 2 Plain Washer M12 FAS2345P 2 Locknut M12 FAS Connecting Link SC Bolt M12 x 45 FAS9681P 1 Bolt M12 x 50 FAS9682P 1 Plain Washer M12 FAS2345P 2 Locknut M12 FAS Outlet Chute Upper SC Bolt M12 x 55 FAS9683P 2 Plain Washer M12 FAS2345P 2 Locknut M12 FAS Outlet Chute - Lower SC Bolt M12 x 50 FAS9682P 2 Plain Washer M12 FAS2345P 2 Locknut M12 FAS Housing Top SC Setscrew M12 x 25 FAS2677P 6 Plain Washer M12 FAS2345P 12 Locknut M12 FAS Setscrew M10 x 25 FAS2654P 2 Cup Square Bolt M10 x 25 FAS9262P 2 Plain Washer M10 FAS2344P 6 Locknut M10 FAS Chute Ram CYL Pivot Pin - Housing SC Pivot Pin Chute TRM Spring Tension Pin 8 x 40 FAS Inspection Plate SC Plain Washer M8 FAS2343P 5 Locknut M8 FAS Connecting Link SC Setscrew M12 x 40 FAS2680P Plain Washer M12 FAS2345P 2 Locknut M12 FAS

23 BED CHAIN DRIVE Ref. Description Part No. Q ty. Associated Components Part No. Q ty. 1 Gearbox Guard SC Cup Square Bolt M8 x 20 FAS9241P 1 Washer M8 FAS2343P 1 Locknut M8 FAS Retaining Disc SC Bed Chain Speed Indicator SC Plain Washer M12 FAS2345P 1 Disc Spring SPR Locknut M12 FAS Indicator Mount Disc SC Threaded bar SC Plain nut M12 FAS2304P 2 5 Gearbox SC Key 12 x 8 x 140 FAS Setscrew M12 x 35 FAS2679P 6 Shakeproof Washer M12 FAS Gearbox Mounting Plate SC Setscrew M12 x 35 FAS2679P 4 Plain Washer M12 FAS2345P 8 Locknut M12 FAS Gasket SC Hydraulic Motor 400cc HYD Setscrew M12 x 50 FAS2682P 2 Plain Washer M12 FAS2345P 2 Bonded Seal 1/2 BSP HYD /2 x 3/8" M/M Union HYD Key 8 x 7 x 30 FAS Seal Kit - SAM Hydraulics HYD

24 FLOOR ASSEMBLY Ref. Description Part No. Q ty Associated Components Part No. Q ty. 1 Floor Section SC Setscrew M12 x 25 FAS2677P 2 Setscrew M12 x 35 FAS2678P 2 Setscrew M12 x 45 FAS2681P 4 Plain Washer M12 FAS2345P 16 Locknut M12 FAS Sprocket Scraper LH SC Cup Square Bolt M12 x 30 FAS9283P 2 Plain Washer M12 FAS2345P 2 Locknut M12 FAS Bearing BRG Setscrew M16 x 40 FAS2703P 8 Locknut M16 FAS Grease Nipple M6 BRG Bearing Mounting Plate SC Cup Square Bolt M12 x 25 FAS9282P 8 Plain Washer M12 FAS2345P 8 Locknut M12 FAS Front Sprocket SC Setscrew M12 x 35 FAS2679P 1 Washer 50 x 13 x 5mm FAS2383P 1 Spring Washer M12 FAS2374P 1 6 Sprocket Scraper RH SC Cup Square Bolt M12 x 30 FAS9283P 2 Plain Washer M12 FAS2345P 2 Locknut M12 FAS Slat c/w Extension SC Joiner RS Locknut M14 FAS Chain section 9 links SC Rear Shaft Scraper RH SC Cup square Bolt M12 x 30 FAS9283P 2 Plain Washer M12 FAS2345P 2 Locknut M12 FAS Bed Chain Tensioner SC Plain Washer M24 FAS2348P 4 Plain Nut M24 FAS2307P 4 M10 x 10 Grub Screw FAS

25 Ref Description Part No. Q ty. Associated Components Part No. Q ty. 12 Tensioner Mounting Plate RH SC Setscrew M12 x 35 FAS2679P 1 Cup Square Bolt M12 x 30 FAS9283P 4 Plain Washer M12 FAS2345P 6 Locknut M12 FAS Chain Wheel SC Bush BRG Rear Shaft SC Grease Nipple 1/8 BSP BRG Tensioner Mounting Plate LH SC Setscrew M12 x 35 FAS2679P 1 Cup Square Bolt M12 x 30 FAS9283P 4 Plain Washer M12 FAS2345P 6 Locknut M12 FAS Rear Shaft Scraper LH SC Cup Square Bolt M12 x 30 FAS9283P 2 Plain Washer M12 FAS2345P 2 Locknut M12 FAS Rear Floor Section SC UNBRAKED AXLE Ref. Description Part No. Q ty. Associated Components Part No. Q ty. 1 Wheel nut WE Wheel 285/70 R Stud WE Unbraked axle SC Bolt M20 x 140 FAS9742P 4 Plain washer M20 FAS2347P 4 Locknut M20 FAS

26 1005 SINGLE CROSSBEATER & DRIVE Ref. Description Part No. Q y. Associated Components Part No. Q ty. 1 Crossbeater SC Blade - Bent SC Setscrew M8 x 20 FAS2627P 28 Locknut M8 FAS Blade - Straight SC Setscrew M8 x 20 FAS2627P 80 Locknut M8 FAS Holding Plate SC Setscrew M8 x 20 FAS2627P 4 Plain Washer M8 FAS2343P 4 Spring Washer FAS2353P 4 5 Shield Ring SC Setscrew M10 X 20 FAS2652P 6 Locknut M10 FAS Mid Body Panel RH SC Setscrew M12 x 30 FAS2678P 3 Washer M12 FAS2345P 6 Locknut M12 FAS Flange Bearing 50mm BRG Setscrew M16 x 35 FAS2702P 8 Spring Washer M16 FAS2356P 8 Grease Nipple M6 Straight BRG Rotor Bearing Cover SC Top Cover Mount RH SC Setscrew M12 x 30 FAS2678P 2 Washer M12 FAS2345P 4 Locknut M12 FAS

27 Ref. Description Part No. Q ty. Associated Component Part No. Q ty. 10 Top Cover Retainer SC Setscrew M8 x 20 FAS2627P 4 Locknut M8 FAS Side Extension RH SC Setscrew M12 x 25 FAS2677P 3 Setscrew M12 x 30 FAS2678P 1 Bolt M12 x 70 FAS9686P 1 Washer M12 FAS2345P 10 Locknut M12 FAS Top Cover SC Top Cover Handle SC Setscrew M8 x 20 FAS2627P 2 Locknut M8 FAS Internal Material Cover SC Bale Guide Plate SC Setscrew M12 x 30 FAS2678P 10 Washer M12 FAS2345P 10 Locknut M12 FAS Bale Restraint Beam SC Setscrew M12 x 30 FAS2678P 6 Washer M12 FAS2345P 12 Locknut M12 FAS Restraint Finger Long SC Setscrew M12 x 35 FAS2679P 12 Washer M12 FAS2345P 24 Locknut M12 FAS Restraint Finger Short SC Setscrew M12 x 35 FAS2679P 8 Washer M12 FAS2345P 16 Locknut M12 FAS Top Cover Mount LH SC Setscrew M12 x 30 FAS2678P 2 Washer M12 FAS2345P 4 Locknut M12 FAS Side Extension LH SC Setscrew M12 x 25 FAS2677P 3 Setscrew M12 x 30 FAS2678P 1 Bolt M12 x 70 FAS9686P 1 Washer M12 FAS2345P 10 Locknut M12 FAS Cover Plate LH SC Setscrew M8 x 20 FAS2627P 2 Washer M8 FAS2343P 2 22 Hinged Chain Guard SC Setscrew M8 x 20 FAS2627P 3 Washer M8 FAS2343P 3 Locknut M8 FAS Mid Body Panel LH SC Setscrew M12 x 30 FAS2678P 4 Washer M12 FAS2345P 8 Locknut M12 FAS Driveline Spacer 5mm SC Shear Sprocket Complete SC (Items 21-23) 25 Centre Hub SC Sprocket Bush SC Bush BRG Shear Sprocket 25 Tooth SC Sprocket Bush SC Shearbolt M8 x 50 (10.9) FAS Locknut M8 FAS Grease Nipple 1 / 4 BSF Straight BRG Washer 80 x 13 x 10mm FAS4810P1 Setscrew M12 x 35 FAS2679P 1 Spring Washer M12 FAS2374P 1 Key ½ x ⅜ x 45 FAS Chain 79 Links SC Joiner ROP Half Link Joiner ROP

28 T1010 TWIN CROSSBEATER & DRIVE & DRIVE Ref. Description Part No. Q ty. Associated Components Part No. Q ty. 1 Crossbeater SC Holding Plate SC Setscrew M8 x 20 FAS2627P 8 Plain Washer M8 FAS2343P 8 Spring Washer FAS2353P 8 3 Shield Ring SC Setscrew M10 X 20 FAS2652P 12 Locknut M10 FAS Mid Body Panel RH SC Flange Bearing 50mm BRG Setscrew M16 x 35 FAS2702P 16 Spring Washer M16 FAS2356P 16 Grease Nipple M6 Straight BRG Rotor Bearing Cover SC Upper Mid Body Panel RH SC Setscrew M12 x 30 FAS2678P 2 Plain Washer M12 FAS2345P 2 Locknut M12 FAS

29 Ref Description Part No. Q ty Associated Components Part No. Q ty Lower Restraint Assy. Complete SC (Items 8, 10, 11) Upper Restraint Assy. Complete SC (Items 8 to 11) 8 Bale Restraint Beam SC Setscrew M10 x 25 FAS2677P 4 Plain Washer M10 FAS2344P 4 Setscrew M12 x 35 FAS2679P 8 Washer M12 FAS2345P 16 Locknut M12 FAS Finger Extension SC Bolt M12 x 40 FAS9680P 10 Washer M12 FAS2345P 20 Locknut M12 FAS Restraint Finger Long SC Bolt M12 x 40 FAS9680P 18 Washer M12 FAS2345P 36 Locknut M12 FAS Restraint Finger Short SC Bolt M12 x 40 FAS9680P 12 Washer M12 FAS2345P 24 Locknut M12 FAS Upper Mid Body Panel LH SC Setscrew M12 x 30 FAS2678P 2 Plain Washer M12 FAS2345P 2 Locknut M12 FAS Driveline Spacer 5mm SC Sprocket 21 Tooth SC Key 1 / 2 x 3 / 8 x 45 FAS Washer 80 x 13 x 10mm FAS4810P 2 Setscrew M12 x 35 FAS2679P 2 Spring Washer FAS2374P 2 16 Chain - 83 Links SC Joiner ROP Half link joiner ROP Tensioner Anchor Nut SC Crossbeater Chain Tensioner SC Tensioner Boss mm SC Tensioner Roller SC Bolt M12 x 90 FAS9690P 1 21 Driveline Spacer 3mm SC Shear Sprocket Complete SC (Items 22-24) 22 Shear Hub SC Key 1 / 2 x 3 / 8 x 75 FAS Bush BRG Shear Sprocket 38 Tooth SC Shearbolt M8 x 50 (10.9) FAS Locknut M8 FAS Bush BRG Grease Nipple 1 / 4 BSF Straight BRG Sprocket Bush SC Mid Body Panel LH SC

30 1010 CROSSBEATER UNIT & BODY PANELS Ref. Description Part No. Q ty. Associated Components Part No. Q ty. 1 Crossbeater Unit SC Setscrew M10 x 25 FAS2677P 2 Plain Washer M10 FAS2344P 4 Locknut M10 FAS Setscrew M12 x 30 FAS2678P 21 Plain Washer M12 FAS2345P 42 Locknut M12 FAS Top Guard SC Cup Square Bolt M8 x 15 FAS9240P 2 Cup Square Bolt M8 x 20 FAS9241P 6 Plain Washer M8 FAS2343P 8 Locknut M8 FAS Top Cover SC Setscrew M8 x 20 FAS2627P 4 Cup Square Bolt M8 x 20 FAS9241P 8 Plain Washer M8 FAS2343P 16 Locknut M8 FAS Greedy Board RH SC Setscrew M12 x 25 FAS2677P 7 Setscrew M12 x 30 FAS2678P 2 Bolt M12 x 70 FAS9686P 2 Plain Washer M12 FAS2345P 22 Locknut M12 FAS

31 Ref. Description Part No. Q ty. Associated Components Part No. Q ty. 5 Inside Panel RH SC Cup Square Bolt M8 x 20 FAS9241P 5 Plain Washer M8 FAS2343P 5 Locknut M8 FAS Setscrew M12 x 25 FAS2677P 1 Plain Washer M12 FAS2345P 2 Locknut M12 FAS Inside Panel LH SC Cup Square Bolt M8 x 20 FAS9241P 5 Plain Washer M8 FAS2343P 5 Locknut M8 FAS Setscrew M12 x 25 FAS2677P 1 Plain Washer M12 FAS2345P 2 Locknut M12 FAS Greedy Board LH SC Setscrew M12 x 25 FAS2677P 7 Setscrew M12 x 30 FAS2678P 2 Bolt M12 x 70 FAS9686P 2 Plain Washer M12 FAS2345P 22 Locknut M12 FAS Hinged Chain Guard SC Setscrew M8 x 20 FAS2627P 2 Plain Washer M8 FAS2343P 7 Locknut M8 FAS Sprocket Cover SC Setscrew M10 x 25 FAS2654P 2 Plain Washer M10 FAS2344P 2 Locknut M10 FAS Chain 85 Links SC Joiner ROP Half Link Joiner ROP Blade - Bent SC Setscrew M8 x 20 FAS2627P 56 Locknut M8 FAS Blade - Straight SC Setscrew M8 x 20 FAS2627P 160 Locknut M8 FAS DECALS Description Part No. Q ty Description Part No. Q ty Teagle DL Tighten wheel nuts DL "Please read the instruction book" DL Bed chain speed indicator DL Yellow body stripe DL m Tomahawk DL DL DL Fingers being severed DL Do not permit riders DL Crushed body DL Blockage removal tool DL Gearbox speed DL PTO speed 540 rpm DL Thrown objects DL Serial number plate T1005 DL Serial number plate T1010 DL Pop rivets FAS

32 BODY Ref. Description Part No. Qty. Associated Components Part No. Qty. 1 Front Drive Cover SC Setscrew M8 x 20 FAS2627P 1 Cup square bolt M8 x 15 FAS9240P 2 Plain Washer M8 FAS2343P 3 Locknut M8 FAS PTO Guard Plastic PTO Setscrew M8 x 20 FAS2627P 4 Plain Washer M8 FAS2343P 4 3 Valve Guard SC Setscrew M8 x 20 FAS2627P 1 Plain Washer M8 FAS2343P 1 Setscrew M12 x 25 FAS2677P 2 Plain Washer M12 FAS2345P 2 4 Cover Plate RH SC Setscrew M8 x 20 FAS2627P 2 Plain Washer M8 FAS2343P 2 5 Front Side Assy. RH SC Cup Square Bolt M12 x 25 FAS9282P 4 Plain Washer M12 FAS2345P 4 Locknut M12 FAS Setscrew M16 x 40 FAS2703P 1 Plain Washer M16 FAS2346P 2 Locknut M16 FAS Mudguard RH (Braked Axle Only) SC Cup Square Bolt M10 x 20 FAS9261P 2 Plain Washer M10 FAS2344P 2 Locknut M10 FAS

33 Ref. Description Part No. Qty. Associated Components Part No. Qty. 7 Side Strengthener SC Bolt M12 x 65 FAS9685P 4 Plain Washer M12 FAS2345P 8 Locknut M12 FAS Rear Side Assy. RH SC Cup Square Bolt M12 x 25 FAS9282P 3 Plain Washer M12 FAS2345P 3 Locknut M12 FAS Bolt M16 x 90 FAS9713P 2 Plain Washer M16 FAS2346P 4 Locknut M16 FAS Guide Plate RH SC Bolt M10 x 70 FAS9663P 3 Locknut M10 FAS Tailgate Post SC Headed Pin FAS6267P 2 R Pin 3mm FAS6003P 2 11 Chain SC Setscrew M10 x 20 FAS2652P 2 Plain Washer M10 FAS2344P 2 Locknut M10 FAS Chain Retainer SC Tailgate SC Pivot Pin SC Spring Tension Pin 8 x 40 FAS Post Bracket SC Cup Square Bolt M10 x 20 FAS9261P 4 Plain Washer M10 FAS2344P 4 Locknut M10 FAS Guide plate LH SC Bolt M10 x 70 FAS9663P 3 Locknut M10 FAS Remote switch bracket. SC Setscrew M8 x 20 FAS2627P 2 Plain Washer M8 FAS2343P 2 16 Rear Side Assy. LH SC Cup Square Bolt M12 x 25 FAS9282P 3 Plain Washer M12 FAS2345P 3 Locknut M12 FAS Bolt M16 x 90 FAS9713P 2 Plain Washer M16 FAS2346P 4 Locknut M16 FAS Mudguard LH (Braked Axle Only) SC Cup Square Bolt M10 x 20 FAS9261P 2 Plain Washer M10 FAS2344P 2 Locknut M10 FAS Middle Stiffener SC Cup Square Bolt M12 x 25 FAS9282P 20 Plain Washer M12 FAS2345P 20 Locknut M12 FAS Front Side Assy. LH SC Cup Square Bolt M12 x 25 FAS9282P 4 Plain Washer M12 FAS2345P 4 Locknut M12 FAS Setscrew M16 x 40 FAS2703P 1 Plain Washer M16 FAS2346P 2 Locknut M16 FAS

34 BALE LIFT (EXPORT MARKET ONLY) Ref. Description Part No. Qty. Associated Components Part No. Qty. KIT - Bale Lift Assy. Complete SC Rear Side Assy. RH SC Cup Square Bolt M12 x 25 FAS9282P 3 Plain Washer M12 FAS2345P 3 Locknut M12 FAS Bolt M16 x 90 HT (8.8) FAS9713P 2 Plain Washer M16 FAS2346P 4 Locknut M16 FAS Lead In Panel SC Cup Square Bolt M10 x 20 FAS9261P 4 Plain Washer M10 FAS2344P 4 Locknut M10 FAS Bale Lift SC Bale Lift Assy. SC Bolt M12 x 65 FAS9685P 4 Plain Washer M12 FAS2345P 3 Locknut M12 FAS Ram Pivot Pin SC Setscrew M8 x 20 FAS2627P 2 Locknut M8 FAS Chute Ram CYL Ram Cover SC Cup square bolt M8 x 20 FAS9241P 8 Plain Washer M8 FAS2343P 8 Locknut M8 FAS Rear Side Assy. LH SC Cup Square Bolt M12 x 25 FAS9282P 3 Plain Washer M12 FAS2345P 3 Locknut M12 FAS Bolt M16 x 90 HT (8.8) FAS9713P 2 Plain Washer M16 FAS2346P 4 Locknut M16 FAS

35 Ref. Description Part No. Q ty. Associated Components Part No. Q ty. 9 Hose Clamp 1/2 SC Setscrew M8 x 35 FAS2631P 6 10 Hose Clamp Bent SC Hose Clamp Straight SC Top Link Post Pin TRM Spring Tension Pin 8 x 40 FAS Ram Pivot Pin SC Setscrew M8 x 20 FAS2627P 4 Locknut M8 FAS Fill In Panel SC (Optional Extra) SOLENOID VALVE Ref Description Part No. Q ty. Associated Components Part No. Q ty 1 Valve RH HYD Valve SC HYD Valve DC HYD Valve TC HYD / 2 x 1 / 2 BSP M/M union HYD / 2 x 1 / 4 BSP M/M union HYD / 2 x 3 / 8 BSP M/M union HYD Bonded seal 1 / 2 BSP HYD / 2 x 1 / 2 BSP M/M union HYD / 2 x 1 / 4 BSP M/M union HYD / 2 x 3 / 8 BSP M/M union HYD Bonded seal 1 / 2 BSP HYD / 2 x 1 / 2 BSP M/M union HYD / 2 x 1 / 4 BSP M/M union HYD / 2 x 3 / 8 BSP M/M union HYD Bonded seal 1 / 2 BSP HYD / 2 x 1 / 2 BSP M/M union HYD / 2 x 1 / 4 BSP M/M union HYD / 2 x 3 / 8 BSP M/M union HYD Bonded seal 1 / 2 BSP HYD Valve Mount Bracket SC Setscrew M8 x 16 FAS2625P 4 Washer M8 FAS2343P 4 Description Part No. RH SC DC TC Cover (Bed control end) HYD Relief valve assembly HYD Double acting slice HYD Flow control slice HYD Bed reverse slice HYD Outlet Cover HYD Flow dividing slice HYD Complete valve seal kit HYD Valve slice seal kit HYD Reverse slice seal kit HYD Flow control slice seal kit HYD

36 LIGHTS Ref Description Part No. Q ty Associated Components Part No. Q ty KIT Lighting Complete SC Lighting loom SC (includes items 1,2,3,10, 12 & 13) 1 Tractor to machine lead EC pin socket EC Socket head cap screw M6 x40 FAS Plain washer M6 FAS2342P 3 Locknut M6 FAS Marker light EC Setscrew M6 x 20 FAS2603P 4 Plain washer M6 FAS2342P 8 Locknut M6 FAS Front marker light arm RH SC Setscrew M8 x 20 FAS2627P 1 Plain washer M8 FAS2343P 2 Locknut M8 FAS Lynch pin FAS Front marker light bracket RH SC Cup square bolt M8 x 20 FAS9241P 2 Plain washer M8 FAS2343P 2 Locknut M8 FAS Pin socket mounting bracket SC Setscrew M10 x 25 FAS2654P 4 Plain washer M10 FAS2344P 8 Locknut M10 FAS Front marker light bracket LH SC Cup square bolt M8 x 20 FAS9241P 2 Plain washer M8 FAS2343P 2 Locknut M8 FAS Front marker light arm LH SC Setscrew M18 x 20 FAS2627P 1 Plain washer M8 FAS2343P 2 Locknut M8 FAS Lynch pin FAS Cable Clip SC Setscrew M8 x 20 FAS2627P 2 Plain washer M8 FAS2343P 2 Locknut M8 FAS Number plate light EC Plain nut M4 FAS2329P 2 Shakeproof washer M4 FAS9207P 2 11 Rear light mount RH SC Rear light unit RH EC Rear lens EC Plain nut M6 FAS2301P 2 Shakeproof washer M6 FAS9209P 2 13 Rear light unit LH EC Rear lens EC Plain nut M6 FAS2301P 2 Shakeproof washer M6 FAS9209P 2 14 Rear light mount LH SC

37 ELECTRONIC CONTROLS - LARGE RAISED FLAT BUTTONS Standard Swivel Dual Ref Description Chute Chute Chop & TC Q ty Associated Components Part No. Q ty Control Box Assembly SC3580 SC3579 SC Battery to cab cable SC3529 SC3529 SC A fuse SC3535 SC3535 SC Power cable SC3503 SC3503 SC Cable gland SC3504 SC3504 SC Enclosure SC3506 SC3506 SC Base SC3506A SC3506A SC3506A 1 Lid SC3506D SC3506C SC3506B 1 6 Potentiometer SC3513 SC3513 SC /8 Joystick SC3510 SC3510 SC Micro-switches SC Male crimp contacts SC3516 SC3516 SC Control box socket SC3515 SC3515 SC M4 x 16 Pan Head FAS2430S 4 M4 Locknut FAS2329S 4 11 Support Bracket SC3538 SC3538 SC M4 x 16 Pan Head FAS2430S 4 M4 Locknut FAS2329S 4 Junction Box Assembly SC3583 SC3582 SC Crimp contacts SC3519 SC3519 SC Cable socket SC3518 SC3518 SC Core cable assy 4m SC3522 SC3522 SC Core cable assy 5m SC3592 SC3592 SC Core cable assy 5m SC3594 SC3594 SC PCB (Large Controls) SC3575 SC3575 SC M4 x 3/8 Pan Head FAS Cable gland SC3524 SC3524 SC Enclosure SC3525 SC3525 SC M4 x 16 Pan Head FAS2430S 4 M4 Locknut FAS2329S 4 18 Sealing Gland. SC SC SC Solenoid cable - long. SC3548 SC3548 SC Connector Screw SC Solenoid cable -short. SC Connector Screw SC SC SC

38 HYDRAULIC HOSES 36

39 Ref Description Part No. Q ty Associated Components Part No. Q ty A Valve supply hose HYD Bonded seal ½ BSP HYD Male coupling HYD B Pressure line filter to valve HYD C Bed motor hose HYD D Chute ram hose - outer HYD E Chute ram hose - inner HYD F Valve to 'T' piece HYD /4 BSP T piece M/M/F HYD /4 BSP T piece M/M/M HYD G Tailgate ram front hose HYD H Tailgate ram rear hose HYD /4 BSP T piece M/M/F HYD J Giraffe chute ram hose HYD K Swivel motor hose HYD Bonded seal 1/2 BSP HYD /2-1/4 BSP M/M union HYD Bale Lift Hoses L Valve to 'T' piece HYD /4 BSP T piece M/M/M HYD M Bale lift ram top hose HYD N Bale lift ram bottom hose HYD Dual chop unit hoses P Valve to 'T' piece HYD /4 BSP T piece M/M/M HYD Q Chop unit side hose HYD R Chop unit rear hose HYD /4 BSP M/F elbow HYD Brake line hose S Tractor to ram HYD Bonded seal ½ BSP HYD Female brake coupling HYD NOT SHOWN Strap non re-useable FAS PRESSURE LINE FILTER Ref Description Part No. Q ty Associated Components Part No. Q ty 1 Filter mounting bracket SC Setscrew M10 x 16 FAS2650P 3 Plain washer M10 FAS2344P 3 Setscrew M10 x 20 FAS2652P 2 Locknut M10 FAS Pressure line filter HYD /2 BSP - M22 M/M union HYD Bonded seal 22mm HYD Not Shown Filter Element HYD

40 COMER PTO SHAFT COMBINED SLIP & OVERRUN CLUTCH Ref Description Part No. Qty Ref Description Part No. Qty PTO Shaft complete 540rpm PTO8086 PTO Shaft complete 1000rpm PTO8079 Tractor end half shaft 540rpm PTO2785 Tractor end half shaft 1000rpm PTO2786 Machine end half shaft PTO Cross journal kit PTO Outer Yoke PTO x 80mm Spring tension pin FAS Outer tube PTO Outer guard retaining ring PTO Anchor chain PTO Guard Clip PTO Inner tube PTO x 70mm Spring tension pin FAS Inner Yoke PTO Flanged yoke PTO Bush PTO Clutch plate x 102 PTO Overrun clutch body PTO Inner plate PTO Intermediate plate PTO Pressure plate PTO M10 x 100mm Bolt FAS Spring PTO M10 Locknut FAS Inner Circlip FAS Retaining Washer PTO Hub - 6 Spline PTO Ratchet Tooth PTO Spring PTO Spring push ring PTO Spring PTO Sliding sleeve collar PTO Outer circlip PTO Inner guard retaining ring PTO Pull back collar set PTO Spline yoke PTO Spline yoke PTO Pull back collar set PTO Clutch Assembly PTO T60 Guard Complete PTO * Spring length to give correct slip clutch torque setting is 32.5mm 38

41 COMER PTO SHAFT WIDE ANGLE C.V. JOINT FOR TRAILED MACHINES Tube Ref Description Part No. Qty Ref Description Part No. Qty PTO Shaft complete 540rpm PTO8085 PTO Shaft complete 1000rpm PTO8088 Tractor end half shaft 540rpm PTO2737 Tractor end half shaft 1000rpm PTO2738 Machine end half shaft PTO Cross journal kit - c.v. joint PTO Outer yoke PTO x 80mm Spring tension pin FAS Outer cap PTO Wiper PTO Outer tube PTO Inner tube PTO Inner cap PTO Inner yoke PTO x 70 Spring tension pin FAS Flanged yoke PTO Bush PTO Clutch plate x 102 PTO Overrun clutch body PTO Inner plate PTO Intermediate plate PTO Pressure plate PTO M10 x 100mm Bolt FAS Spring PTO M10 Locknut FAS Inner circlip FAS Retaining washer PTO Hub - 6 spline PTO Spring push ring PTO Spring PTO Sliding sleeve collar PTO Outer circlip PTO Spring PTO Ratchet tooth PTO Guard Clip PTO Outer guard retaining ring PTO Inner guard retaining ring PTO Wide angle double yoke PTO Collar kit set PTO Clutch Assembly PTO Spline wide angle collar yoke PTO Spline wide angle collar yoke PTO Anchor chain PTO Cone guard set PTO T60 Guard Complete PTO (Does not include item 38) * Spring length to give correct slip clutch torque setting is 32.5mm 39

42 WIRING DIAGRAM LIGHTS 40