SAFETY FIRST! HEALTH AND SAFETY AT WORK WARRANTY

Transcription

1

2 1. READ THE INSTRUCTION BOOK THOROUGHLY before attempting to operate or carry out any maintenance on the machine. If you do not understand any part of this manual, ask your dealer for assistance. 2. ALWAYS CARRY OUT SAFE MAINTENANCE. Never clean, adjust or maintain the machine until the engine has been stopped, the machine come to rest, the PTO disengaged and the key removed. 3. NEVER WORK UNDER A MACHINE RAISED ON THE 3-POINT LINKAGE unless it is securely supported. 4. NEVER OPERATE THE MACHINE WITH ANY PARTS OR GUARDS MISSING. Check that all guards including the PTO shaft guards are in good condition and in place before operating the machine. 5 OPERATE SAFELY. Before starting work, check that there are no persons or animals in the immediate vicinity of the machine or tractor. Always maintain full control of the tractor and machine. Ensure that you know how to stop the tractor and machine quickly in case of emergency. SAFETY FIRST! 6. SECURE THE PTO GUARD BY MEANS OF CHECK CHAINS to suitable points on the tractor and machine to prevent the outer plastic shield from rotating. 7. NEVER STAND BETWEEN THE MACHINE AND THE TRACTOR WHEELS. 8. DO NOT WEAR LOOSE OR RAGGED CLOTHING 9. BEWARE OF DUST. Under dusty conditions, keep the cab windows and doors closed. The use of a dust mask conforming to EN149 is strongly recommended. 10. BEWARE OF HIGH NOISE LEVELS. Some tractor/implement combinations give noise levels in excess of 90dB at the operator's ear. Under such circumstances, ear defenders should be worn. Keep cab windows and doors closed to reduce noise level. Throughout this handbook, the term `tractor' is used to refer to the power source used to drive the machine. It does not necessarily refer to a conventional agricultural tractor. HEALTH AND SAFETY AT WORK Our equipment is designed so as to conform with current Health & Safety Regulations and therefore poses no significant hazard to health when properly used. Nevertheless, in the interests of all concerned, it is essential that equipment of our manufacture is used in accordance with the instructions that are supplied or are available from our Technical Staff. Legislation requires that all operators are instructed in the safe operation, cleaning and maintenance of equipment and machines. This handbook forms part of that instruction and it must be read and understood before fitting the machine onto the tractor or attempting to use it. Your supplier is responsible for carrying out any necessary pre-delivery inspection, fitting the machine onto the tractor and test running. The supplier must also give instruction in the safe use, maintenance and adjustment of the machine. In the interests of safety, please ensure that the instructions referred to above are brought to the attention of all your employees who are to use the equipment. We recommend that the use of this equipment is restricted to capable trained operatives. Persons under the age of sixteen should not operate the machine and should be kept away from where it is being used. WARRANTY The standard warranty is for 12 calendar months against faulty materials and workmanship. Components supplied as part of the original machine, but manufactured by another company, e.g. PTO shafts, wheels etc., are subject to the original manufacturer's conditions and warranty. Where repairs are carried out under warranty:- a) Claims for the fitting of non original parts will not be considered unless prior agreement has been obtained. b) The repairer must be advised that the work is to be the subject of a warranty claim beforehand. c) Any claim must be submitted within four weeks of the repair. d) The damaged parts must be retained for inspection and returned carriage paid if required. The right to withdraw warranty is reserved if:- a) Non-original parts are fitted. b) The machine has been abused, badly maintained or used for purposes other than that for which it was designed.

3 INDEX INSTURCTIONS PARTS LISTS Page Instructions 1 Comer discharge rotor gearbox with side output shaft from December Comer discharge rotor gearbox with side output shaft from March Comer discharge rotor gearbox with side output shaft from November Bed chain gearbox - Tomahawk 1005 and 1010 models 8 Bed chain gearbox - Tomahawk 9090 models 9 Comer discharge rotor gearbox 10 BIMA discharge rotor gearbox with side output shaft 11 Comer discharge rotor gearbox with extended input shaft 12 BIMA discharge rotor gearbox with extended input shaft 13 Comer cross beater gearbox 14 COMER (EG Transmissions) PTO shaft models 15 COMER PTO shaft models 16 COMER (EG Transmissions) PTO shaft 17 COMER PTO shaft - Combined slip and overrun clutch 18 COMER PTO shaft Wide angle C.V. joint 19 EG Transmissions PTO shaft Wide angle C.V. joint 20 Notes 21 INSTURCTIONS After 50 hours of use the gearbox oil should be drained and replaced with new oil. To drain the oil, remove the valve guard, remove the drain and filler plugs and allow it to empty. Waste oil should be collected and disposed of at an oil recycling facility. Refill the gearbox with SAE90.EP gearbox oil. 1

4 COMER DISCHARGE ROTOR GEARBOX WITH SIDE OUTPUT SHAFT Used on all Tomahawk models with gearboxes made from December To identify the date of gearbox manufacture, refer to the date stamp on the gearbox makers identification plate. The month of production is represented by the corresponding letter, A being January, D being April. The two numbers that follow indicate the year. 2

5 Ref Description Part No. Q ty Ref Description Part No. Q ty Gearbox complete SC Casing SC elbow SC Breather SC Cover SC Bolt FAS Washer 8.5 x 25 x 2.5 FAS Lever SC Gear 36 tooth SC Key 14 x 9 x 25 FAS Bearing 6212 BRG Int. spring ring FAS Double lip seal 60 x 80 x 10 BRG Key 18 x 11 x 70 FAS Output shaft SC Cap 22 x 4 SC Int. spring ring FAS Cap 80 x 10 AT Taper roller bearing BRG Gear 32 tooth SC Spacer SC Lay shaft SC Shim 79.9 SC Cap 100 x 10 SC Taper roller bearing BRG Spacer 40.5 x 63.5 x 5 SC Gear 26 tooth SC Shim 43.6 x 1.0 SC Cap 110 x 10 SC Crown wheel SC Plug ½ FAS Double lip seal 40 x 80 x 10 BRG Input shaft SC Level Plug SC Gear 23 tooth SC Ext. spring ring FAS Gear 26 tooth SC M10 x 16 H.T. bolt FAS Int. spring ring FAS O-ring OR-3062 HYD Spacer 82 x 89.6 x 5 SC Pivot SC Shim 32.0 SC Ball 7 / mm SC Spring SC Ext. spring ring FAS Shim 25.6 x 2.5 SC Pad SC Copper washer SC Plug 3 / 8 HYD Bonded seal HYD M16 x 25mm H.T. bolt FAS Taper roller bearing BRG Shim 89.7 x 2 SC Int. spring ring FAS Shim 51.5 SC Shim 40.3 x 2.5 SC Pinion shaft 6 spline SC Ext. spring ring FAS Double lip seal 40 x 90 x 8.7 BRG Shim 71.7 x 1.0 SC Shim 89.7 SC Taper roller bearing BRG Oil capacity 5 litres SAE90.EP 3

6 COMER DISCHARGE ROTOR GEARBOX WITH SIDE OUTPUT SHAFT Used on all Tomahawk models with gearboxes made from March 2008 until December To identify the date of gearbox manufacture, refer to the date stamp on the gearbox makers identification plate. The month of production is represented by the corresponding letter, A being January, D being April. The two numbers that follow indicate the year. 4

7 Ref Description Part No. Q ty Ref Description Part No. Q ty Gearbox complete SC Casing SC elbow SC Breather SC Cover SC Bolt FAS Washer 8.5 x 25 x 2.5 FAS Lever SC Gear 36 tooth SC Key 14 x 9 x 25 FAS Bearing 6212 BRG Int. spring ring FAS Double lip seal 60 x 80 x 10 BRG Key 18 x 11 x 70 FAS Output shaft SC Cap 22 x 4 SC Int. spring ring FAS Cap 80 x 10 AT Taper roller bearing BRG Gear 32 tooth SC Spacer SC Lay shaft SC Shim set 79.9 SC Int. spring ring FAS Taper roller bearing BRG Spacer 40.5 x 63.5 x 5 SC Gear 26 tooth SC Shim 43.6 x 1.0 SC Cap 110 x 10 SC Crown wheel SC Plug ½ FAS Double lip seal 40 x 80 x 10 BRG Input shaft SC Level Plug SC Gear 23 tooth SC Ext. spring ring FAS Gear 26 tooth SC M10 x 16 H.T. bolt FAS Cap 100 x 10 SC O-ring OR-3062 HYD Spacer 82 x 89.6 x 5 SC Pivot SC Shim 32.0 SC Ball 7 / mm SC Spring SC Ext. spring ring FAS Shim 25.6 x 2.5 SC Pad SC Copper washer SC Plug 3 / 8 HYD Bonded seal HYD M16 x 25mm H.T. bolt FAS Taper roller bearing BRG Shim 89.7 x 2 SC Int. spring ring FAS Shim 51.5 SC Shim 40.3 x 2.5 SC Pinion shaft 6 spline SC Ext. spring ring FAS Double lip seal 40 x 90 x 8.7 BRG Shim 71.7 x 1.0 SC Shim 89.7 SC Taper roller bearing BRG Oil capacity 5 litres SAE90.EP 5

8 COMER DISCHARGE ROTOR GEARBOX WITH SIDE OUTPUT SHAFT Used on all Tomahawk models with gearboxes made from November 2000 until March To identify the date of gearbox manufacture, refer to the date stamp on the gearbox makers identification plate. The month of production is represented by the corresponding letter, A being January, D being April. The two numbers that follow indicate the year. 6

9 Ref Description Part No. Q ty Ref Description Part No. Q ty Gearbox complete SC Casing SC elbow SC Breather SC Cover SC Bolt FAS Washer 8.5 x 25 x 2.5 FAS Lever SC Gear 36 tooth SC Key 14 x 9 x 25 FAS Bearing 6212 BRG Int. spring ring FAS Double lip seal 60 x 80 x 10 BRG Key 18 x 11 x 70 FAS Output shaft SC Cap 22 x 4 SC Int. spring ring FAS Cap 80 x 10 AT Taper roller bearing BRG Gear 32 tooth SC Spacer SC Lay shaft SC Shim set 79.7 SC Int. spring ring FAS Taper roller bearing BRG Spacer 40.5 x 63.5 x 5 SC Gear 26 tooth SC Shim 43.6 x 1.0 SC Cap 110 x 10 SC Crown wheel SC Plug ½ FAS Double lip seal 40 x 80 x 10 BRG Input shaft SC Level Plug SC Gear 23 tooth SC Ext. spring ring FAS Gear 26 tooth SC M10 x 16 H.T. bolt FAS Cap 100 x 10 SC O-ring OR-3062 HYD Spacer 82 x 89.6 x 5 SC Pivot SC Shim 32.0 SC Ball 7 / mm SC Spring SC Ext. spring ring FAS Shim 25.6 x 2.5 SC Pad SC Copper washer SC Plug 3 / 8 HYD Bonded seal HYD M16 x 25mm H.T. bolt FAS Taper roller bearing BRG Shim 89.7 x 2 SC Int. spring ring FAS Shim 51.5 SC Shim 40.3 x 2.5 SC Pinion shaft SC Ext. spring ring FAS Double lip seal 40 x 90 x 8.7 BRG Shim 71.7 x 1.0 SC Oil capacity 5 litres SAE90.EP 7

10 BED CHAIN GEARBOX Used on Tomahawk 1005 and 1010 models Ref Description Part No. Q ty Ref Description Part No. Q ty Gearbox complete SC Casing RT190 SC Bearing 6013 BRG Oil seal 65 x 100 x 10 BRG Shaft - 45mm SC Circlip internal 62 FAS Cap seal BRG Pinion shaft straight tooth SC Pinion bevel tooth SC Bearing 6010 BRG Circlip - internal 80 FAS Circlip - external 50 FAS Gear SC Circlip - external 72 FAS Circlip - internal 100 FAS Crown wheel SC Bearing 6305 BRG Key 8 x 7 x 30 FAS Setscrew M8 x 16 FAS Cover plate SC Cover plate gasket SC Sight glass SC Plug HYD Oil capacity 2.5 litres SAE90.EP 8

11 BED CHAIN GEARBOX Used on Tomahawk 9090 models from serial number 1501 Ref Description Part No. Q ty Ref Description Part No. Q ty Gearbox complete SC Casing SC Bearing 6012 BRG Oil seal 60 x 95 x 10 BRG Shaft SC Circlip internal 62 FAS Cap seal SC Pinion straight tooth SC Pinion bevel tooth SC Bearing 6010 BRG Circlip - internal 80 FAS Circlip - external 50 FAS Gear SC Circlip - external 65 FAS Circlip - internal 95 FAS Crown wheel SC Bearing 6305 BRG Key 8 x 7 x 30 FAS Setscrew M8 x 16 FAS Cover SC Gasket SC Sight glass SC Plug HYD Oil capacity 2 litres SAE90.EP 9

12 COMER DISCHARGE ROTOR GEARBOX Used on Tomahawk 808 models from serial number 1500 with hydraulically driven cross beater Ref Description Part No. Q ty Ref Description Part No. Q ty 1 Casing SC Bearing 6212 BRG Spacer SC Gear 26 tooth SC Output shaft SC Double lip seal 60 x 80 x 10 BRG Key 18 x 11 x 70 FAS Plug 3/8 HYD Copper Washer 16 x 22 x 1 FAS4812C 2 10 Gear 32 tooth SC Spacer SC Internal circlip 80mm FAS Level / drain plug FAS Cap AT Taper roller bearing BRG Lay shaft SC Setscrew M16 x 25 FAS Breather SC Gear 26 tooth SC Cap 22x4 SC External circlip 46mm FAS Bottom cover SC Setscrew M8 x 16 FAS Double lip seal 40 x 80 x10 BRG Shim set 79.7 SC Input shaft SC Setscrew M16 x 25 FAS Setscrew M10 x 25 FAS Front cover SC o elbow SC

13 BIMA DISCHARGE ROTOR GEARBOX WITH SIDE OUTPUT Used on Tomahawk 8080 models from serial number 2600 to 2899 Ref Description Part No. Q ty Ref Description Part No. Q ty 1 Lever SC Hub SC Gear SC Shaft SC Gear SC Shaft SC Gear SC Sleeve SC Gear SC Sleeve SC Shaft SC Shaft SC Gear SC Hub SC Sleeve SC Housing SC Cover SC Pad SC Circlip D16E FAS Circlip D45E FAS Circlip D85I FAS Circlip D95E FAS Circlip D100I FAS Circlip D110I FAS Oil seal 45x85x10 BRG Oil seal 60x110x13 BRG Oil seal OR3043 BRG Key 18x11x70 SC Key 20x12x21 SC Bearing 6209 BRG Bearing BRG Bearing BRG Bearing 6212 BRG Spring SPR Ball 5/16 SC Sleeve 16x24x0.4 SC Pin 6x30 UNI 6874 FAS Oil plug ½ G SC Oil plug ½ G SC Setscrew M10 x 55 UNI 5931 FAS Oil plug RCA 85 SC Oil plug RCA100 SC Setscrew M6 x 16 UNI 5739 FAS Gearbox oil EP90 7 litres 11

14 COMER DISCHARGE ROTOR GEARBOX EXTENDED INPUT SHAFT Used on Tomahawk 8080 models from serial numbers 2500 to 2509, 2511, 2521 to 2599 Ref Description Part No. Q ty Ref Description Part No. Q ty 1 Casing SC Selector SC Gear 36 tooth SC Key 14 x 9 x 25 FAS Gear 26 tooth SC Key 18 x 11 x 70 FAS Output shaft SC Bearing 6212 BRG Gear 32 tooth SC Taper roller bearing BRG Cap AT Spacer SC Lay shaft SC Internal circlip 80mm FAS Gear 26 tooth SC Input shaft SC External circlip 46mm FAS Shim set 79.7 SC Double lip seal 40 x 80 x 10 BRG Level / drain plug FAS Gear 23 tooth SC Setscrew M10 x 25 (8.8) FAS Front cover SC External circlip 95mm FAS Plug 3/8 HYD elbow SC Breather SC Selector handle SC Spring tension pin 6 x 25 FAS Wiper seal 16 x 22 x 3/4 HYD Selector handle shaft SC Bonded seal 3/8 HYD Spring housing SC Plain nut M16 FAS2305P 1 35 Grub screw M10 x 14 FAS Roll pin 6 x 30 FAS Roll pin 3.5 x 30 FAS Spring SC Ball 8.7 SC Setscrew M8 x 16 FAS Bottom cover SC Double lip seal 60 x 80 x 10 BRG

15 BIMA DISCHARGE ROTOR GEARBOX EXTENDED INPUT SHAFT Used on Tomahawk 8080 models from serial numbers 2510, 2512 to serial number 2520 Details not available at this time. Please Contact Teagle For Advice. Ref Description Part No. Q ty Ref Description Part No. Q ty 13

16 CROSS BEATER GEARBOX Used on Tomahawk 8080 models from serial number 2501 To serial number 2599 Keyed Splined Keyed Splined Ref Description gears gears Q ty Ref Description gears gears Q ty 1 Cap SC3254 SC Internal circlip 72 FAS7112 FAS Shim set 71.7 SC3255 SC Bearing 6207 BRG1062 BRG Setscrew M10 x 20 (8.8) FAS2652 FAS Plug HYD1457 HYD Cover SC3256 SC Gear 18 tooth - splined SC Gear 14 tooth keyed SC Shim set 48.0 SC3258 SC Taper roller bearing BRG Ball bearing 6207 BRG Double lip seal 35x72x10 BRG3042 BRG Output shaft SC3264 SC Casing SC3260 SC External circlip 40 FAS7013 FAS Spacer SC3261 SC External circlip 35 FAS7016 FAS Input shaft SC3265 SC Key 10 x 8 x 35 FAS

17 COMER (EG TRANSMISSIONS) PTO SHAFT TOMAHAWK POINT LINKAGE MOUNTED MACHINES ONLY **Parts for shafts with either a black plastic sliding sleeve collar or the metal sliding sleeve collar **Steel **Plastic Common Parts Ref Description Part No. Part No. Q'ty. Ref. Description Part No. Qty. PTO Shaft comp. 540rpm PTO8084 PTO Tractor end half shaft PTO1928 PTO complete with guard. Machine end half shaft PTO1929 PTO complete with guard. 1 Outer circlip PTO2711 PTO Sliding sleeve collar PTO2712 PTO Ball hold up ring PTO Spring PTO2713 PTO Spring push ring PTO1906 PTO Inner circlip FAS7112 FAS Retaining washer PTO1907 PTO Hub - 6 spline PTO2714 PTO Hub- 21 spline PTO2715 PTO Ball PTO1910 PTO Ratchet tooth PTO1911 PTO Ratchet spring PTO1912 PTO Retaining washer PTO1913 PTO Outer casing with yoke PTO1914 PTO Grease nipple BRG5033 BRG M8 x 1 straight 15 Cross journal kit PTO2321 PTO Grease nipple BRG5049 BRG M8 x 1 x 45 o 17 Outer tube yoke PTO1915 PTO Spring tension pin 10 x 80 FAS Outer Tube PTO Inner tube PTO Spring tension pin 10 x 70 FAS Inner tube yoke PTO Dirt Shield PTO Spring PTO Flanged yoke PTO Bush PTO Friction lining 153 x 91.5 x 3 PTO Splined hub c/w item 29 PT Bolt M12 x 65 FAS Locknut M12 FAS Inner plate PTO Pressure plate PTO Bolt M10 x 80 FAS Locknut M10 FAS Outer guard retaining ring PTO Inner guard retaining ring PTO Guard bolt PTO Chain PTO PTO Guard complete PTO * Spring length to give correct slip clutch torque setting is 32.5mm.

18 COMER PTO SHAFT COMBINED SLIP & OVERRUN CLUTCH TOMAHAWK POINT LINKAGE MOUNTED MACHINES ONLY Ref Description Part No. Q'ty Ref Description Part No. Q'ty PTO Shaft complete 540rpm PTO Shaft complete 1000rpm Tractor end half shaft complete with guard 540rpm Tractor end half shaft complete with guard 1000rpm Machine end half shaft complete with guard. PTO8084 PTO8072 PTO2785 PTO2786 PTO Pull back collar set PTO Spline yoke PTO Spline yoke PTO Cross journal kit - c.v. joint PTO Outer yoke PTO x 80mm Spring tension pin FAS Outer tube PTO Inner tube PTO x 70mm Spring tension pin FAS Inner yoke PTO M10 x 100mm Bolt FAS M10 Locknut FAS Flanged yoke PTO Bush PTO Clutch plate x 102 PTO Overrun clutch body PTO Inner plate PTO Intermediate plate PTO Pressure plate PTO Spring PTO Inner circlip FAS Retaining washer PTO Spring PTO Ratchet tooth PTO Hub - 6 spline PTO Clamp plate PTO Bolt M12 Fine x 95 FAS Locknut M12 Fine FAS Outer guard retaining ring PTO Chain MB Inner guard retaining ring PTO Outer half guard PTO Inner half guard PTO * Spring length to give correct slip clutch torque setting is 35.2mm 16

19 COMER (EG TRANSMISSIONS) PTO SHAFT - TOMAHAWK 808, 8080 & 9090 **Parts for shafts with either a black plastic sliding sleeve collar or the metal sliding sleeve collar **Steel **Plastic 2 Plate 4 Plate Ref Description Part No. Part No. Q ty Ref Description Clutch Clutch Q ty PTO Shaft comp. 540rpm PTO8086 PTO Tractor end c/w guard PTO2708 PTO Machine end c/w guard 2 Plate Clutch PTO2758 PTO Plate Clutch PTO2709 PTO Outer circlip PTO2711 PTO Sliding sleeve collar PTO2712 PTO Ball hold up ring PTO Spring PTO2713 PTO Spring push ring PTO1906 PTO Inner circlip FAS7112 FAS Retaining washer PTO1907 PTO Hub - 6 spline PTO2714 PTO Hub - 21 spline PTO2715 PTO Ball PTO1910 PTO Ratchet tooth PTO1911 PTO Ratchet spring PTO1912 PTO Retaining washer PTO1913 PTO Outer casing with yoke PTO1914 PTO Grease nipple M8 BRG5033 BRG Cross journal kit PTO2321 PTO Grease nipple M8x45 o BRG5049 BRG Outer tube yoke PTO1915 PTO Spring tension pin 10x80 FAS4147 FAS Outer tube PTO2705 PTO Inner tube PTO2706 PTO Spring tension pin FAS4145 FAS x Inner tube yoke PTO1918 PTO Spring PTO1921 PTO Flanged yoke PTO1920 PTO Bush PTO1922 PTO Friction lining PTO x 91.5 x PTO Splined hub PTO1992 PT Bolt M12 x 65 FAS4720 FAS Locknut M12 FAS4714 FAS Inner plate PTO1962 PTO Small Inner Plate PTO Pressure plate PTO1963 PTO Bolt M10 x FAS Bolt M10 x 80 FAS Locknut M10 FAS2333 FAS Outer retaining ring PTO1925 PTO Chain PTO2336 PTO Inner retaining ring PTO1926 PTO Guard bolt PTO1930 PTO Guard complete PTO2704 PTO Spring Length to give correct slip clutch torque setting is :- 4 Plate Clutch = 32.0 mm 2 Plate Clutch = 32.5 mm

20 COMER PTO SHAFT COMBINED SLIP & OVERRUN CLUTCH. TOMAHAWK 808, 8080 & 9090 Ref Description Part No. Q'ty Ref Description Part No. Q'ty PTO Shaft complete 540rpm PTO Shaft complete 1000rpm Tractor end half shaft complete with guard 540rpm Tractor end half shaft complete with guard 1000rpm Machine end half shaft complete with guard. PTO8086 PTO8080 PTO2785 PTO2786 PTO Pull back collar set PTO Spline yoke PTO Spline yoke PTO Cross journal kit - c.v. joint PTO Outer yoke PTO x 80mm Spring tension pin FAS Outer tube PTO Inner tube PTO x 70mm Spring tension pin FAS Inner yoke PTO M10 x 100mm Bolt FAS M10 Locknut FAS Flanged yoke PTO Bush PTO Clutch plate x 102 PTO Overrun clutch body PTO Inner plate PTO Intermediate plate PTO Pressure plate PTO Spring PTO Inner circlip SPR Retaining washer PTO Spring PTO Ratchet tooth PTO Ball ½ PTO Hub - 6 spline PTO Spring push ring PTO Spring PTO Sliding sleeve collar PTO Outer circlip PTO Outer guard retaining ring PTO Chain PTO Inner guard retaining ring PTO Outer half guard PTO Inner half guard PTO * Spring length to give correct slip clutch torque setting is 35.2mm 18

21 COMER PTO SHAFT WIDE ANGLE C.V. JOINT FOR TRAILED MACHINES Tube Ref Description Part No. Q'ty Ref Description Part No. Q'ty PTO Shaft complete 540rpm PTO Shaft complete 1000rpm Tractor end half shaft complete with guard 540rpm Tractor end half shaft complete with guard 1000rpm Machine end half shaft complete with guard. PTO1413 PTO1414 PTO2737 PTO2738 PTO Splined wide angle collar yoke PTO Splined wide angle collar yokepto Cross journal kit - c.v. joint PTO Wide angle double yoke PTO Outer yoke PTO x 80mm Spring tension pin FAS Outer cap PTO Outer tube PTO Wiper PTO Outer circlip PTO Sliding sleeve collar PTO Spring PTO Fixed sleeve PTO Ball ½ PTO Splined collar yoke PTO Splined collar yoke PTO Wide angle c.v. joint-outer tube PTO Inner tube PTO Inner cap PTO x 70mm Spring tension pin FAS Inner yoke PTO Cross journal assembly PTO M10 x 100mm Bolt FAS M10 Locknut FAS Flanged yoke PTO Bush PTO Clutch plate x 102 PTO Overrun clutch body PTO Inner plate PTO Intermediate plate PTO Pressure plate PTO Spring PTO Inner circlip FAS Retaining washer PTO Spring PTO Ratchet tooth PTO Hub - 6 spline PTO Spring push ring PTO Bolt Type EN Guard CE Guard 2005 On 36 Inner guard retaining ring PTO1926 PTO Bolt PTO Outer guard retaining ring PTO1925 PTO Bearing ring PTO1973 PTO Guard cone set PTO1974 PTO Outer half guard PTO1971 PTO Chain PTO2336 PTO Inner half guard PTO1972 PTO * Spring length to give correct slip clutch torque setting is 35.2mm 19

22 EG TRANSMISSIONS PTO SHAFT WIDE ANGLE C.V. JOINT Tube Section Ref Description Part No. Q'ty Ref Description Part No. Q'ty PTO Shaft complete 540rpm PTO PTO Shaft complete 1000rpm PTO Tractor end half shaft PTO complete with guard 540rpm Tractor end half shaft PTO complete with guard 1000rpm Machine end half shaft PTO complete with guard. 1 6 Splined wide angle yoke PTO Splined wide angle yoke PTO Cross journal kit - c.v. joint PTO Wide angle double yoke PTO Outer tube yoke PTO x 80mm Spring tension pin FAS Outer tube rislan coated PTO Push pin PTO Wide angle joint 540rpm PTO Wide angle joint 1000rpm PTO Inner tube rislan coated PTO x 70mm Spring tension pin FAS Inner tube yoke PTO Cross journal assembly PTO M10 x 100mm Bolt FAS M10 Locknut FAS Flanged yoke PTO Bush PTO Clutch plate x 102 PTO Overrun clutch body PTO Inner plate PTO Intermediate plate PTO Pressure plate PTO Spring PTO Overrun + slip clutch assy PTO Inner circlip FAS Retaining washer PTO Spring PTO Ratchet tooth PTO Ball PTO Hub - 6 spline PTO Spring push ring PTO Spring PTO Ball hold up ring PTO Sliding sleeve collar PTO Outer Circlip PTO Chain PTO Inner guard retaining ring PTO Bolt PTO Outer guard retaining ring PTO Bearing ring PTO Guard cone set PTO Outer half guard PTO Inner half guard PTO * Spring length to give correct slip clutch 35.2 mm

23 NOTES 21

24