Revised on : 23. May TECHNICAL GUIDE PARTS CATALOGUE. Cal.NH70/71 AUTOMATIC MECHANICAL. SII Products
|
|
|
- Molly Heath
- 5 years ago
- Views:
Transcription
1 Revised on : 23. May TECHNICAL GUIDE & PARTS CATALOGUE AUTOMATIC MECHANICAL SII Products
2 [SPECIFICATION] PARTS CATALOGUE / TECHNICAL GUIDE NH70 - NH71 Gilt version of NH70 Movement Movement size Time indication Basic function Frequency Accuracy Duration time Static accuracy Measurement position Lift angle Measurement time Posture difference Isochronisms (24h-0h) Winding the mainspring Outside diameter Ф 27.4mm Casing diameter Jewels Normal Crown position Clockwise position First click Counterclockwise Ф 27.0mm Total height 5.32mm 3Hands (hour, minute, second) Manual winding Automatic winding with ball bearing Stop-second device 21,600 vibrations per hour -20~+40 seconds per day * Measurement should be done within 10~60 minutes after fully wound up Direction of 3 positions (1) Dial up (2) 9 o'clock up (3) 6 o'clock up 53 deg 20 seconds * Equipment to be used : Witschi WATCH EXPERT Difference is under 60 seconds with max value and minimum value * Measurement should be done within 10~60 minutes after fully wound up * Direction of 4 positions (1) 12 o'clock up (2) 9 o'clock up (3) 6 o'clock up (4) 3 o'clock up -20~+40 seconds per day * Measurement position : Dial up * Difference of static accuracy of 24 h and 0h More than 41 hours Mainspring after fully wound up * Posture to confirmation : Dial up << Movement >> Fully wound up by turning the crown minimum 55 times Fully wound up by turning the ratchet wheel screw 8 times << Complete Watch >> A winding machine is needed to wind up the mainspring Full wind up conditions Rotary speed : 30 rpm Operating time: 60 minutes 24 jewels Free Manual winding Time setting SII Products 1
3 Disassembling procedures Figs. 1 5 Reassembling procedures Figs. 5 1 PARTS CATALOGUE Type of oil Oil quantity mark Moebius 9010 NORMAL QUANTITY S-6 SUFFICIENT QUANTITY S Hour wheel guard screw 2 Hour wheel guard Refer to page 6 for each parts code Hour wheel *2 8-2 Lower shock absorbing spring 8-3 Lower shock absorbing cap jewel Minute wheel and pinion Cannon pinion 8-4 Lower hole jewel frame for shock-absorber *2 SII Products 2
4 Disassembling procedures Figs Reassembling procedures Figs PARTS CATALOGUE Type of oil Oil quantity mark Moebius 9010 NORMAL QUANTITY S-6 SUFFICIENT QUANTITY S-4 1 Oscillating weight with ball bearing Refer to page 6 for each parts code *2 * Automatic train bridge screw Balance bridge screw 3 Automatic train bridge Refer to page 6 for each parts code whole tooth Second reduction wheel and pinion 8 Balance cock Refer to Ratchet wheel screw page 6 for each parts code 6 Ratchet wheel Refer to page 6 for each parts code Pallet bridge screw Balance complete with stud *3 10 Pallet bridge Refer to page 6 for each parts code Pallet fork *3 8-2 Upper shock absorbing spring 8-3 Upper shock absorbing cap jewel 8-4 Upper hole jewel frame for shock-absorber SII Products 3
5 PARTS CATALOGUE Type of oil Oil quantity mark Moebius 9010 S-6 NORMAL QUANTITY S-4 SUFFICIENT QUANTITY First reduction wheel Barrel and train wheel bridge screw Refer to page 7 for oiling spot 13-1 Cap jewelled spring 13-2 Cap jewel Pawl lever Ratchet sliding wheel spring Refer to page 9 for the assembling method 13 Barrel and train wheel bridge with hole jewel frame Refer to page 6 for each parts code Refer to page 7 for oiling spot Reduction wheel holder Lower plate for barrel and train wheel bridge Fourth wheel and pinion Lower plate for barrel and train wheel bridge screw Third wheel and pinion Click 23 Barrel complete with mainspring Refer to page 6 for each parts code SII Products 4
6 PARTS CATALOGUE Type of oil Oil quantity mark Moebius 9010 S-6 NORMAL QUANTITY S-4 SUFFICIENT QUANTITY Center wheel bridge screw Center wheel bridge Escape wheel and pinion Center wheel and pinion Yoke spring screw Yoke spring Yoke Balance stop lever Setting lever *2 *3 *4 Refer to page 8 for oiling spot *4 * Clutch wheel * Winding pinion Winding stem 36 Main plate SII Products 5
7 PARTS CATALOGUE 2 Hour wheel guard (P-2) Cal. Parts code Cal. Parts code NH NH Oscillating weight with ball bearing (P-3) Cal. Parts code Marking Cal Japan mark NH70 NH Malaysia mark Parts code Marking Japan mark 3 Automatic train bridge (P-3) Cal. Parts code Cal. Parts code 6 Ratchet wheel (P-3) Cal. Parts code Cal. Parts code NH NH NH NH Balance cock (P-3) 10 Cal. Parts code Cal. Parts code NH NH Pallet bridge (P-3) Cal. Parts code Cal. Parts code NH NH Barrel and train wheel bridge with hole jewel frame (P-4) Cal. Parts code Cal. Parts code NH NH Barrel complete with mainspring (P-4) Cal. Parts code Cal. Parts code NH NH List of screw Page No Parts code Parts name Parts form Page No Parts code Parts name Parts form P-2 1 P-3 2 P-4 19 P-5 Hour wheel guard screw (x3) Automatic train bridge screw (x2) Pallet bridge screw (x2) 24 Lower plate for barrel and train wheel bridge screw Center wheel bridge screw P-3 P-3 7 P Ratchet wheel screw Balance bridge screw Barrel and train wheel bridge screw (x3) P Yoke spring screw (x2) SII Products 6
8 TECHNICAL GUIDE Type of oil Oil quantity mark Moebius 9010 NORMAL QUANTITY S-6 SUFFICIENT QUANTITY S-4 1.Oiling spot 13 Barrel and train wheel bridge with hole jewel frame Barrel and train wheel bridge with hole jewel frame (back side) *3 *2 *3 *4 *2 Note *2 After oiling, set lower plate for barrel and train wheel bridge & screw 18 Lower plate for barrel and train wheel bridge 19 Lower plate for barrel and train wheel bridge screw *4 After oiling, set first reduction wheel & pawl lever & reduction wheel holder 17 First reduction wheel 17 First reduction wheel 16 Pawl lever 15 Reduction wheel holder SII Products 7
9 32 Balance stop lever Balance stop lever TECHNICAL GUIDE Main plate Contact part of main plate and balance stop lever 2.Setting position of oscillating weight Before assembling oscillating weight Match the center of the oscillating weight and winding stem. Set the hole of first reduction wheel gear on the imaginary line toward the balance bridge guide pin. Enlarged view Balance bridge guide pin First reduction wheel gear 3.To remove the winding stem 1) Set the winding stem to normal position 2) Pull out the winding stem, while pushing "A" A 31 Setting lever 33 Winding stem SII Products 8
10 TECHNICAL GUIDE 4.Disassembling / assembling of the First reduction wheel << Disassembling >> << Assembling >> 17 First reduction wheel 15 Reduction wheel holder 13 Barrel and train wheel bridge (back side) 5.Disassembling / assembling of the Ratchet sliding wheel spring << Disassembling >> << Assembling >> 14 Ratchet sliding wheel spring 13 Barrel and train wheel bridge with hole jewel frame PUSH Remove the hook of the ratchet sliding wheel spring from barrel and train wheel bridge with hole jewel frame. The hooks of ratchet sliding wheel spring are hung up on barrel and train wheel bridge with hole jewel frame. SII Products 9
11 6.Accuracy adjustment TECHNICAL GUIDE Regulator Stud support Regulator pin Note: Regulator Time adjustment Stud support Beat error adjustment (+) side (-) side Regulator pin Gap adjustment of balance spring and regulator pin Anticlockwise rotation No clockwise rotation SII Products 10
12 TECHNICAL GUIDE 7.To wind up the mainspring <<Movement>> The mainspring would be fully wound up by turning the ratchet wheel screw 8 times clockwise. (Manual winding or Screwdriver) Manual winding Rotate crown clockwise at normal position by minimum 55 times. (Equal to ratchet wheel screw 8 times ) Screwdriver winding Turn the ratchet wheel screw 8 times clockwise. [ Manual winding ] [ Screwdriver winding ] Screwdriver Ratchet wheel screw Ratchet wheel 8.How to attach hands Place the movement directly on a flat metal plate or something similar to attach the hands. We recommend the use of movement holder to attach hands. Static weighting For hands attachment, please use a special equipment. When the movement receives a strong shock, it may be damaged. Metal plate 9.Accuracy measurement condition Static Accuracy : -20~+40 seconds per day Measurement Conditions 1) Measurement should be done within 10~60 minutes after fully wound up 2) Lift angle : 53 deg 3) Measurement position : (1) Dial up (2) 9 o'clock up (3) 6 o'clock up 4) Minimum measurement Time : 20 seconds 5) Stabilizing Time : Leave the watch for at least 20 seconds to stabilize after you change its measurement position. SII Products 11
13 OPERATION Minute hand Hour hand Crown at first position Crown at normal position Second hand 1.How to set the time 1) Pull out the crown to the first click position 2) Turn the crown to set hour and minute hands 3) Push the crown back into the normal position 2.To wind up the mainspring a) Manual winding Rotate the crown clockwise at normal position Wind turning the ratchet wheel screw 8 times. It will start to move naturally after shaking slightly. b) To wind up with winding machine Full wind up conditions Rotary speed : 30 rpm Operating time : 60 minutes SII Products 12
Revised on : 07. Feb TECHNICAL GUIDE PARTS CATALOGUE. Cal.NE15C AUTOMATIC MECHANICAL. SII Products
Revised on : 07. Feb. 2018 TECHNICAL GUIDE & PARTS CATALOGUE AUTOMATIC MECHANICAL SII Products [SPECIFICATION] Item PARTS CATALOGUE / TECHNICAL GUIDE Version-02 NE15C Cal. No. Movement Movement size Time
PARTS CATALOGUE / TECHNICAL GUIDE Cal.NE57A Version-01 NE57A [SPECIFICATION] Cal. No. Item. Movement. Outside diameter. Movement size.
![PARTS CATALOGUE / TECHNICAL GUIDE Cal.NE57A Version-01 NE57A [SPECIFICATION] Cal. No. Item. Movement. Outside diameter. Movement size.](/thumbs/89/100003756.jpg "PARTS CATALOGUE / TECHNICAL GUIDE Cal.NE57A Version-01 NE57A [SPECIFICATION] Cal. No. Item. Movement. Outside diameter. Movement size.")
[SPECIFICATION] Item PARTS CATALOGUE / TECHNICAL GUIDE NE57A Cal. No. Movement Movement size Time indication Basic function Frequency Accuracy Duration time Outside diameter Static accuracy Winding the
TECHNICAL GUIDE PARTS CATALOGUE. Cal.NE15 AUTOMATIC MECHANICAL. SII Products
TECHNICAL GUIDE & PARTS CATALOGUE AUTOMATIC MECHANICAL [SPECIFICATION] Item PARTS CATALOGUE / TECHNICAL GUIDE Version-01 NE15 Cal. No. Movement Movement size Time indication Basic function Frequency Accuracy
TECHNICAL GUIDE PARTS CATALOGUE. Cal.NE20 AUTOMATIC MECHANICAL. SII Products
TECHNICAL GUIDE & PARTS CATALOGUE AUTOMATIC MECHANICAL [SPECIFICATION] Item PARTS CATALOGUE / TECHNICAL GUIDE Version-01 NE20 Cal. No. Movement Movement size Time indication Basic function Frequency Accuracy
PARTS LIST / TECHNICAL GUIDE Automatic Cal.4R71A
[SPECIFICATION] Item PARTS LIST / TECHNICAL GUIDE Automatic Cal.4R71A Cal. No. 4R71A 3 Hands (Hour, Minute and Second hands) Movement Size Diameter Outside : φ27.4 mm Casing : φ27.0 mm Height : 5.32 mm
PARTS LIST/ TECHNICAL GUIDE
/ TECHNICAL GUIDE Cal. 7S26C/7S36C [SPECIFICATIONS] Item Cal. No. 7S26C 7S36C 5 4 28 29 3 2 1 31 30 3 hands (hour, minute and second hands) Date indication Day indication Movement size Diameter Outside:
PARTS LIST / TECHNICAL GUIDE
[SPECIFICATIONS] PARTS LIST / TECHNICAL GUIDE Automatic Item Cal. No. 4R35B/4R36A The figures below are Cal. 4R36A. 3 hands (hour, minute and second hands) Day and Date indication Movement size Diameter
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE [SPECIFICATIONS] Brand SEIKO Item Cal. No. 7S26B 7S36B Movement Movement size Outside diameter Casing diameter Height (x 1.5) Ø 27.4 mm Ø 27.0 mm 4.9 mm Time indication
Revised on : 9. Mar TECHNICAL GUIDE PARTS CATALOGUE. Cal.VJ22B Cal.VJ24B ANALOGUE QUARTZ. SII Products
Revised on : 9. Mar. 2016 TECHNICAL GUIDE & PARTS CATALOGUE Cal.VJ22B Cal.VJ24B ANALOGUE QUARTZ PARTS CATALOGUE / TECHNICAL GUIDE VJ22B VJ24B [SPECIFICATION] Item Cal. No. VJ22B VJ24B Version-02 Movement
Revised on. : 05. Jun TECHNICAL GUIDE PARTS CATALOGUE. Cal.VJ12B Cal.VJ14B ANALOGUE QUARTZ. SII Products
Revised on. : 05. Jun. 2018 TECHNICAL GUIDE & PARTS CATALOGUE Cal.VJ12B Cal.VJ14B ANALOGUE QUARTZ [SPECIFICATION] PARTS CATALOGUE / TECHNICAL GUIDE VJ12B VJ14B Cal. No. Item VJ12B VJ14B Version-02 Movement
Revised on : 25 November 2014 TECHNICAL GUIDE PARTS CATALOGUE. Cal.VC00/01E ANALOGUE QUARTZ. SII Products
Revised on : 25 November 2014 TECHNICAL GUIDE & PARTS CATALOGUE ANALOGUE QUARTZ PARTS CATALOGUE / TECHNICAL GUIDE Cal.VC00 / 01E [SPECIFICATION] Item Cal. No. VC00E VC01E Version-01 Movement Movement size
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE [SPECIFICATIONS] Item Movement Cal. No. V653B Movement size Outside diameter Casing diameter Height ø29.5 mm 26.0 mm between 3 o clock and 9 o clock sides ø28.8 mm 3.7
Cal.VJ5*B Series (VJ52/53/55)
Revised on : 05. Jun. 208 TECHNICAL GUIDE & PARTS CATALOGUE Series (VJ52/53/55) ANALOGUE QUARTZ PARTS CATALOGUE / TECHNICAL GUIDE [SPECIFICATION] Item Cal. No. Series Series VJ52B VJ53B VJ55B Version-02
Cal.VJ4*B Series (VJ42/43/45)
Revised on : 05. Jun. 2018 TECHNICAL GUIDE & PARTS CATALOGUE Series (VJ42/43/45) ANALOGUE QUARTZ [SPECIFICATION] Item PARTS CATALOGUE / TECHNICAL GUIDE Cal. No. Series Series VJ42B VJ43B VJ45B Version-02
Revised on : 9. Mar TECHNICAL GUIDE PARTS CATALOGUE. Cal.VJ20C Cal.VJ21C ANALOGUE QUARTZ. SII Products
Revised on : 9. Mar. 2016 TECHNICAL GUIDE & PARTS CATALOGUE Cal.VJ20C Cal.VJ21C ANALOGUE QUARTZ [SPECIFICATION] Item PARTS CATALOGUE / TECHNICAL GUIDE Cal. No. VJ20C VJ21C VJ20C VJ21C Version-02 Movement
Revised on : 05. Jun TECHNICAL GUIDE PARTS CATALOGUE. Cal.VJ23B Cal.VJ33B ANALOGUE QUARTZ. SII Products
Revised on : 05. Jun. 2018 TECHNICAL GUIDE & PARTS CATALOGUE Cal.VJ23B Cal.VJ33B ANALOGUE QUARTZ [SPECIFICATION] Item PARTS CATALOGUE / TECHNICAL GUIDE Cal. No. VJ23B VJ33B VJ23B VJ33B Version-02 Movement
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE [SPECIFICATIONS] Item Movement Cal. No. Cal. 7N3C Cal. 7N33C Cal. 7N39C 7N3C 7N33C 7N39C Outside diameter The illustrations refer to Cal. 7N33C. ø4.0 mm 1.5 mm between
BULOVA MODELS. Specifications. Designation of Types. 11 AOAC 11 AOACB Automatic 11 AOACD. Date. Movement DIAL SIDE TRAIN SIDE.
DIAL SIDE TRAIN SIDE BULOVA MODELS 11 AOAC 11 AOACB 11 AOACD Date Day + Date Scale 1:1 Specifications Movement 11y,'" Lever escapement 17 or 23 jewels Unbreakable and self-lubricated mainspring Total running
automatic, with center sweep-second automatic, calendar with center sweep-second automatic, day and date with center sweep-second
DIAL SIDE TRAIN SIDE Scale 1:1 Specifications Movement Automatic mechanism 11112 Ligne, lever escapement Diameter of the plate 25.60 mm Unbreakable and self-lubricated mainspring Total running time: 42
Revised on : 29. Feb TECHNICAL GUIDE PARTS CATALOGUE. Cal.VK63/67/83 ANALOGUE QUARTZ. SII Products
Revised on : 29. Feb. 2016 TECHNICAL GUIDE & PARTS CATALGUE Cal. ANALGUE QUARTZ [SPECIFICATIN] PARTS CATALGUE / TECHNICAL GUIDE Cal. Cal. No. Item VK63 VK67 VK83 Version04 Movement Movement size Time indication
Revised on : 29. Feb TECHNICAL GUIDE PARTS CATALOGUE. Cal.VK61/64 ANALOGUE QUARTZ. SII Products
Revised on : 29. Feb. 2016 TECHNICAL GUIDE & PARTS CATALGUE Cal. ANALGUE QUARTZ [SPECIFICATIN] Item PARTS CATALGUE / TECHNICAL GUIDE Cal. Cal. No. VK61 VK64 Version03 Movement Movement size Time indication
Issued on: 11. May TECHNICAL GUIDE PARTS CATALOGUE. Cal.VK61/64 ANALOGUE QUARTZ. SII Products
Issued on: 11. May. 2012 TECHNICAL GUIDE & PARTS CATALGUE Cal. ANALGUE QUARTZ [SPECIFICATIN] Item PARTS CATALGUE / TECHNICAL GUIDE Cal. Cal. No. VK61 VK64 Movement Movement size utside diameter Casing
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE [SPECIFICATIONS] Item Movement Cal. No. 3M62A (x 1.0) Movement size Outside diameter Casing diameter Height ø24.0 mm ø23.3 mm 4.2 mm Time indication Driving system Additional
Calibre General information for Calibre Exploded views for calibre Specific information for calibre
Technical Guide TG-19-C-024-E C Produced by : pelrom Date: 20.09.2010 3 Modifications: see last page CALIBRE 3220 Version A 131/4 Ø 30 mm Height on movement Power reserve Number of jewels Frequency Lift
Specific information for calibre 3603
Fig. 1.0 1.0 Assembling of date indication 1. Stem in position 3 : Turn anti-clockwise the driving wheel for date unlocking yoke (reference 33029) until the finger of this wheel is aligned with the pin,
Servicing a Poljot 3133 movement
Servicing a Poljot 3133 movement A service guide made by WUS member SLLS, June 2015 Editor: WUS member Polmax3133 Use this guide at your own risk. To dismantle a 3133 movement, just start at the end of
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE PARTS CATALOGUE / TECHNICAL GUIDE (p. 1 21) CATÁLOGO DE PARTES / GUÍA TÉCNICA (p. 23 43) [SPECIFICATIONS] Item Movement Cal. No. 5J22A (x 1.0) Movement size Outside diameter
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE PARTS CATALOGUE / TECHNICAL GUIDE (p. 1 22) [SPECIFICATIONS] Item Movement Cal. No. 5J32A (x 1.0) Movement size Outside diameter Casing diameter ø26.4 mm ø25.6 mm Height
Special Points. Specifications TRAIN SIDE DIAL SIDE. Scale 2V2:1
DAL SDE TRAN SDE Scale 2V2:1 Specifications 7% ligne, lever escapement Diameter of plate 17.20 mm. Total running time: 47 hours Screwless beryllium 21,600 beats per hour Adjustable stud holder balance
The chronograph calibres CHRO PC 17 jewels CHRO C12 PC 17 jewels CHRO C12 PC AMPM GMT 17 jewels CHRO PC CAL 17 jewels
Technical guide The chronograph calibres 860 27 CHRO PC 17 jewels 861 27 CHRO C12 PC 17 jewels 910 27 CHRO C12 PC AMPM GMT 17 jewels 930 27 CHRO PC CAL 17 jewels o 27.00 mm / Power-reserve Jewel number
PARTS LIST /TECHNICAL GUIDE ANALOGUE SOLAR Cal. V157A/V158A [SPECIFICATIONS]
![PARTS LIST /TECHNICAL GUIDE ANALOGUE SOLAR Cal. V157A/V158A [SPECIFICATIONS]](/thumbs/86/93687150.jpg "PARTS LIST /TECHNICAL GUIDE ANALOGUE SOLAR Cal. V157A/V158A [SPECIFICATIONS]")
PARTS LIST /TECHNICAL GUIDE ANALOGUE SOLAR [SPECIFICATIONS] Cal. No. Item V157A V157A/V158A Movement V158A Diameter Outside: 28.6 mm Casing: 24.0 mm Height: 3.5mm 3 hands (hour, minute and second hands)
PARTS CATALOGUE / TECHNICAL GUIDE
PRTS CTLOGUE / TECHNICL GUIDE Cal. 7T62, 7T92 [SPECIFICTIONS] Item Cal. No. 7T62 7T92 Movement The illustrations refer to Cal. 7T62. (x 1.0) Movement size Outside diameter Casing diameter ø27.6 mm ø27.0
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE [SPECIFICATIONS] Item Cal. No. 6T63A 3 hands (hour, minute, and small second hand) 24-hour indicator Date indicator Diameter Outside: Ø 30.8 mm Height: 5.1 mm Casing:
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE [SPECIFICATIONS] Item Movement Cal. No. Cal. 5T82A 5T82A (x 1.0) Movement size Time indication Driving system Outside diameter Casing diameter Height (Movement intervals)
PARTS LIST / TECHNICAL GUIDE Perpetual Calendar/Alarm Chronograph Cal. 7T86A
PARTS LIST / TECHNICAL GUIDE Perpetual Calendar/Alarm Chronograph [SPECIFICATIONS] Item Cal. No. Movement 7T86A 7T86A 3 hands (hour, minute, and small second hands) Interval of hands movements Driving
PARTS LIST / TECHNICAL GUIDE ANALOGUE SOLAR Cal. V175A [SPECIFICATIONS]
![PARTS LIST / TECHNICAL GUIDE ANALOGUE SOLAR Cal. V175A [SPECIFICATIONS]](/thumbs/87/95546534.jpg "PARTS LIST / TECHNICAL GUIDE ANALOGUE SOLAR Cal. V175A [SPECIFICATIONS]")
PARTS LIST / TECHNICAL GUIDE ANALOGUE SOLAR [SPECIFICATIONS] Item Cal. No. V175A 3 hands (hour, minute and small second hands), 24-hour indicator Diameter: Height: Outside 27.6 mm.casing 27.0 mm 4.4 mm
PARTS LIST / TECHNICAL GUIDE
PARTS LIST / ANALOGUE SOLAR [SPECIFICATIONS] Item Cal. No. V172A/V174A V172A V174A 3 hands (hour, minute and small second hands) 3 hands (hour, minute and small second hands), 24-hour indicator Diameter:
PARTS CATALOGUE / TECHNICAL GUIDE
PRTS CTLOGUE / TECHNICL GUIDE [SPECIFICTIONS] Cal. 7T62/7T92/7T94 Item Cal. No. 7T62 7T92 7T94 Movement The illustrations refer to Cal. 7T62. (x 1.0) Movement size Outside diameter Casing diameter Ø 27.6
Cal. VR33A CHRONOGRAPH 13 1/ mm. 3 years. Ø 30.6mm. Watch Movement Specification and Drawing. Movement Size. Casing Diameter.
Watch Movement Specification and Drawing CHRONOGRAPH Cal. VR33A Movement Size 13 1/2 Casing Diameter Ø 30.6mm Height 3.97mm Battery Life 3 years Cal. VR33A Date: 31/Aug./'18 Items Rev. Page Specifications
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE [SPECIFICATIONS] Cal. H021B Cal. H022A Cal. H023A Item Movement Cal. No. H021B, H022A, H023A Movement size Time indication Driving system Display system Outside diameter
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE [SPECIFICATIONS] Item Movement Cal. No. Cal. 7T84A 7T84A (x 1.0) Movement size Time indication Driving system Outside diameter Casing diameter Height Additional mechanism
Cal. VS22A SOLAR SERIES 7 3/ mm. Approx. 6 months. Ø 18.1mm. Watch Movement Specification and Drawing. Movement Size. Casing Diameter.
Watch Movement Specification and Drawing SOLAR SERIES Cal. VS22A Movement Size 7 3/4 Casing Diameter Ø 18.1mm Height 2.76mm Running Time Approx. 6 months Cal. VS22A Date: 29/Jun./'18 Items Rev. Page Features
PARTS LIST / TECHNICAL GUIDE
PARTS LIST / TECHNICAL GUIDE Analogue Solar [SPECIFICATIONS] Item Cal. No. V114A 2 hands (hour, minute hands) Diameter Outside: Ø 15.5 mm x 11.8 mm Casing: Ø 15.15 mm x 11.80 mm Height: Ø 2.0 mm Interval
Caution for disassembling The hour wheel is made of engineering plastics. When pulling out the hour hand, take care not to damage the hour wheel.
III. REMRKS ON DISSSEMLING ND RESSEMLING Hands Dial Caution for disassembling The hour wheel is made of engineering plastics. When pulling out the hour hand, take care not to damage the hour wheel. How
Cal. AS32A SOLAR SERIES 10 1/ mm. Approx. 4 months. Ø 23.3mm. Watch Movement Specification and Drawing. Movement Size. Casing Diameter.
Watch Movement Specification and Drawing SOLAR SERIES Cal. AS32A Movement Size 10 1/2 Casing Diameter Ø 23.3mm Height 4.61mm Running Time Approx. 4 months Date: 31/Oct./'16 Cal. AS32A Items Rev. Page Features
PARTS CATALOGUE/TECHNICAL GUIDE Cal. 7D46A, 7D48A
PARTS CATALOGUE/TECHNICAL GUIDE Cal. 7D46A, 7D48A SPECIFICATIONS Item Cal. No. 7D46A, 7D48A Movement Movement Outside diameter size Casing diameter Height Time indication (Movement intervals) Driving system
Cal. YM92A. φ27.0 mm H 3.7 mm. S.EPSON Products
Cal. YM92A φ27.0 mm H 3.7 mm Items Rev. Page Specifications 03 1 Appearance 00 2 Casing 03 3 Hand fitting 01 4 Hand setting stem 01 5 Dial-01 01 6-01 Dial-02 00 6-02 Dial-03 00 6-03 Dial-04 00 6-04 Casing
Cal.5D22A TECHNICAL GUIDE
No. PROCESS ILLUSTRATIONS AND SPECIAL INSTRUCTIONS ETC. Mount the secondary battery unit. Mount the insulator for secondary battery. Mount the secondary battery guard. Fix the insulator for secondary battery
Cal. VS3JA SOLAR SERIES 10 1/ mm. Approx. 6 months. Ø 24.0mm. Watch Movement Specification and Drawing. Movement Size. Casing Diameter.
Watch Movement Specification and Drawing SOLAR SERIES Cal. VS3JA Movement Size 10 1/2 Casing Diameter Ø 24.0mm Height 3.47mm Running Time Approx. 6 months Date: 2/May/'17 Cal. VS3JA Items Rev. Page Features
2. Uncasing. 5. Remove the clamp screws (casing ring / middle and movement / casing ring) and the clamps. 6. Remove the casing ring.
Calibre 360 1. Presentation 2. Uncasing 3. Chronograph movement (module) / M2 replacement procedure 4. Overhauling the base movement 5. Assembling the base movement with the chronograph movement 6. Chronograph
Cal. VS75A SOLAR SERIES. 4.40mm. Approx. 6 months. Ø 27.0mm. Watch Movement Specification and Drawing. Movement Size. Casing Diameter.
Watch Movement Specification and Drawing SOLAR SERIES Cal. VS75A Movement Size 12 Casing Diameter Ø 27.0mm Height 4.40mm Running Time Approx. 6 months Cal. VS75A Date: 1/Sep./'15 Items Rev. Page Features
Cal. VR43A SOLAR SERIES 13 1/ mm. Approx. 4 months. Ø 30.6mm. Watch Movement Specification and Drawing. Movement Size. Casing Diameter.
Watch Movement Specification and Drawing SOLAR SERIES Cal. VR43A Movement Size 13 1/2 Casing Diameter Ø 30.6mm Height 4.52mm Running Time Approx. 4 months Date: 30/Nov./'17 Cal. VR43A Items Rev. Page Features
Cal. VS37A SOLAR SERIES 10 1/ mm. Approx. 6 months. Ø 24.0mm. Watch Movement Specification and Drawing. Movement Size. Casing Diameter.
Watch Movement Specification and Drawing SOLAR SERIES Cal. VS37A Movement Size 10 1/2 Casing Diameter Ø 24.0mm Height 2.98mm Running Time Approx. 6 months Date: 15/Dec./'17 Cal. VS37A Items Rev. Page Features
7D** Technical Instruction No.1
Assembling the switching unit Set the main plate. 91 Set the main plate. 90 89 88 87 86 85 84 Set the lead pin for RZ1. Set the hour and minute stator. Set the second stator. Set the generating stator.
Cal. VS17A SOLAR SERIES 5 1/ mm. 2.79mm. Approx. 6 months. Watch Movement Specification and Drawing. Movement Size.
Watch Movement Specification and Drawing SOLAR SERIES Cal. VS17A Movement Size 5 1/2 Casing Diameter 11.8 15.15 mm Height 2.79mm Running Time Approx. 6 months Date: 31/Aug/'17 Cal. VS17A Items Rev. Page
CALIBRE Q SCS CAL CORH CORM CORS 7 jewels Description et performances
Technical guide CALIBRE 1370 25.60 Q SCS CAL CORH CORM CORS 7 jewels Description et performances The caliber 1370, destined for a man's electronic watch with analogical display, is fitted with a quartz
Pneumatic-Pneumatic Positioner YT-1200L,R Installation manual
Installation Safety Warning When installing a positioned, please ensure to read and follow safety instruction. All input and supply pressure to valve, actuator, and other related devices must be turned
Smart Positioner YT-2400L,R Installation manual
Installation Safety Warning When installing a positioner, please ensure to read and follow safety instruction. All input and supply pressure to valve, actuator, and other related devices must be turned
This Master Clock is designed for use on small low voltage electric time systems (those operating on up to 10 volts).
[The following is a partial reproduction of an undated brochure entitled Instructions For Care And Installation, Style A Master Clock Made By International Time Recording Co. of New York with general offices
OVERHAUL. 1. REMOVE REPAIR SERVICE STARTER KIT (a) Remove the nut, and disconnect the lead wire from the repair service starter kit.
STARTING & CHARGING 195 OVERHAUL 190C702 1. REMOVE REPAIR SERVICE STARTER KIT (a) Remove the nut, and disconnect the lead wire from the repair service starter kit. A57559 (b) (c) (d) Remove the 2 screws
WESCO INDUSTRIAL PRODUCTS, INC. Manual Non Telescoping High Lift Truck. Part Number: &
WESCO INDUSTRIAL PRODUCTS, INC Manual Non Telescoping High Lift Truck Part Number: 272462 & 272463 Note: Operator MUST read and understand these operating instructions before using this Truck. TABLE OF
DIRECT DRIVE: THE REMARKABLE BULOVA ACCUTRON CALIBER 214
Lehekülg 1/5 13.05.2013 1:04 Search DIRECT DRIVE: THE REMARKABLE BULOVA ACCUTRON CALIBER 214 By Walt Odets Site Map TimeZone Italia Login / Register Register for TimeZone! Registering provides access to
./#0#. 1"&." 1994 ELECTRICAL Suzuki of America Corp. - Starters. Swift
!"" #$%!& '()!)((*(+,*)- 1994 ELECTRICAL Suzuki of America Corp. - Starters Swift Two types of starter motors are used, conventional and reduction gear. Both types of starters consist of yoke assembly,
STRENGTH Enclosed head design seals out contaminants for improved performance and life.
T H E P E R F O R M A Enclosed head design seals out contaminants for improved performance and life. Torque wrap design reduces stress on gear and pawl teeth. Innovative linear ball bearing system eliminates
1GR-FE STARTING STARTER (for 4WD) DISASSEMBLY
14 1GR-FE ARTING ARTER (for 4WD) DISASSEMBLY 1. REMOVE ARTER YOKE ASSEMBLY (a) Remove the nut, then disconnect the lead wire from terminal C. Remove the 2 through bolts. (c) Pull the starter yoke and the
CITYSTORM USER GUIDE
CITYSTORM USER GUIDE Congratulations on your purchase of a GIANT Citystorm. GIANT Citystorm represents the latest in design and engineering, and also requires special care. While Giant icycle engineers
FOR THL MAN BEHIND THE BENCH
FOR THL MAN BEHIND THE BENCH se code s/ Jlaru nzarer1a1 {. for qu ck aid 0 11red BOY PRQOF -wa-fches Reduced view of Boyproof Watch 16 Size, Stem Wind and Set COPYRIGHT 1909 BY THE WESTJ:RN CLOCK MFG.
Short Shifter Installation Instructions Miata 6-Speed manual
Tools required: 10mm deep socket long extension ratchet small flathead screwdriver phillips-head screwdriver Short Shifter Installation Instructions 2006-14 Miata 6-Speed manual IMPORTANT NOTE: This shifter
1 HR-301/D Parts Manual. Table Of Contents
Table Of Contents 301/D Parts Manual 3 Point Hitch...2 Pull-Type Hitch...4 Main Frame...6 Angle Adjuster - Serial Number 44982 & Prior...8 Rotor Assembly - Serial Number 44982 & Prior...10 Rotor Assembly
Synchronous Wired and Electronic Movement Manual
Synchronous Wired and Electronic Movement Manual Hanson Movement General Synchronous-wired and electronic secondaries are controlled by a Hansen movement. Except for a short correction cycle each hour,
DRIVE AXLE Volvo 960 DESCRIPTION & OPERATION AXLE IDENTIFICATION DRIVE AXLES Volvo Differentials & Axle Shafts
DRIVE AXLE 1994 Volvo 960 1994 DRIVE AXLES Volvo Differentials & Axle Shafts 960 DESCRIPTION & OPERATION All 960 station wagon models use type 1041 rear axle assembly. All 960 4-door models use type 1045
1989 Jeep Cherokee. STEERING COLUMN' '1989 STEERING Jeep Steering Columns STEERING COLUMN STEERING Jeep Steering Columns
STEERING COLUMN 1989 STEERING Jeep Steering Columns DESCRIPTION All models use collapsible steering columns. All columns have integral ignition switch and locking device. Optional tilt wheel is available
TECHNICAL SPECIFICATIONS OF THE SPLIT SECONDS CHRONOGRAPH RICHARD MILLE RM 004-V2 FELIPE MASSA
TECHNICAL SPECIFICATIONS OF THE SPLIT SECONDS CHRONOGRAPH RICHARD MILLE RM 004-V2 FELIPE MASSA Following the success of the RM 005 in 2006 and the RM 011 in 2007, the RM 004 is the latest model to carry
Clock and watch escapements, power stamps and hammers, power punch, rotary conveyer, blower, pile driver and miscellaneous devices.
K»\ IX Nos. 1-21) 144 Clock and watch escapements, power stamps and hammers, power punch, rotary conveyer, blower, pile driver and miscellaneous devices. MECHANICAL MODELS 57 Section IX 129. Clock escapement.
Grande Précision TimeMover Collector 48 the time machine
TimeMover Mechanical watches are more than just timekeepers. The lovely ticking of perfectly machined parts combine to produce masterpieces of horology many of which now have achieved collector status.
HKS 700E. Service Manual June Ver. 2.04
HKS 700E Service Manual 009 June Ver..04 HKS CO.,LTD 78 KITAYAMA FUJINOMIYA SHIZUOKA JAPAN 48-09 TEL +8(0)544-54-78 FAX +8(0)544-54-40 hks_aviation@hks-power.co.jp http://www.hks-power.co.jp/hks_aviation/
TABLE OF CONTENTS. Cordless Impact Driver. Model No. EY7542. Europe Oceania
Order Number PTD0707X38CE Cordless Impact Driver Model No. EY7542 Europe Oceania TABLE OF CONTENTS PAGE 1 Warning-------------------------------------------------------------- 2 2 Specifications -----------------------------------------------------
SECTION 9 CRANKING SYSTEM CONTENTS
SECTION 9 CRANKING SYSTEM CONTENTS 9-1. 9-2. 9-3. 9-4. 9-5. 9-6. 9-7. 9-8. GENERAL DESCRIPTION.,...,..., 9-2 SPECIFICATIONS.......................................... 9-4 LUBRICATION 9-5 REMOVAL AND INSTALLATION...
An idea endures three centuries for a reason. Still, that doesn t mean you can t improve it. Mirrored Force Resonance
THE WORLD S FIRST An idea endures three centuries for a reason. Still, that doesn t mean you can t improve it. Mirrored Force Resonance Resonance is a sophisticated and demanding horological technique.
TECHNICAL INFORMATION INFORMACION TECNICA
TECHNICL INFORMTION INFORMCION TECNIC CITIZEN QURTZ Cal. No. E76 (Cal. No. E760) ENGLISH Contents 1. FETURES...1 2. BEFORE USING...1 3. SPECIFICTIONS...2 4. SETTING THE TIME ND DTE...3 5. FUNCTIONS UNIQUE
Disassembly and Reassembly Manual
AS No.ER2-0908-MC-00 ER2 Series Electric Chain Hoist (125kg to 5t) Disassembly and Reassembly Manual Safety precaution This Disassembly and Reassembly Manual includes contents to prevent injury to any
TABLE OF CONTENTS. Cordless Drill & Driver / Cordless Hammer Drill & Driver. (Cordless Drill & Driver) (Cordless Hammer Drill & Driver)
Order Number PTD1007X51CE Cordless Drill & Driver / Cordless Hammer Drill & Driver Model No. EY7441 (Cordless Drill & Driver) Model No. EY7940 (Cordless Hammer Drill & Driver) Europe and Oceania TABLE
Repair Manual VW 02J gearbox. INA GearBOX
Repair Manual VW 02J gearbox INA GearBOX Special tools Pipe section, 50 mm: Press fitting of synchronizer body for third/fourth gear. Assembly of support bearing for input and output shaft. Part number:
G85CS Parts list. Frank Kyul, Netherlands
G85CS Parts list Frank Kyul, Netherlands http://home.wanadoo.nl/fxkuyl/ CYLINDER BARREL & HEAD 022298 Barrel Cylinder 1 022515 Washer Cylinder Base 1 015351 Nut. Sleeve Cylinder Head 4 042157 Washer Sleeve
PARTS LIST FOR NO. 3 SERIES PISTOL AND T HANDLE SCREWDRIVERS
PARTS LIST FOR NO. 3 SERIES PISTOL AND T HANDLE SCREWDRIVERS NON-REVERSING HANDLE ASSEMBLY (SERIAL NO S. STARTING WITH B & D ) Fig. Part Form A278F Date 10-00/B Page 1 of 6 4. 14309 Ring O 5. 14312 Ring
2005 Toyota RAV AUTOMATIC TRANSMISSIONS U240E & U241E Overhaul
2001-05 AUTOMATIC TRANSMISSIONS U240E & U241E Overhaul APPLICATION CAUTION: Flush oil cooler and oil cooler lines prior to transaxle installation. Oil cooling system contamination may cause premature transaxle
SCION xb LOWERING SPRINGS Preparation
Preparation Part Number: PTR07-52080 Kit Contents Item # Quantity Reqd. Description 1 2 Front Springs 2 2 Rear Springs 3 1 Instruction Form Hardware Bag Contents Item # Quantity Reqd. Description 1 2 3
KICK STARTER/DRIVE PULLEY/ CLUTCH/DRIVEN PULLEY SERVICE INFORMATION TROUBLESHOOTING KICK STARTER DRIVE BELT...
8 KICK STARTER/DRIVE PULLEY/ 8 SERVICE INFORMATION... 8-2 TROUBLESHOOTING... 8-2 KICK STARTER... 8-3 DRIVE BELT... 8-7 DRIVE PULLEY... 8-9 STARTER ONE-WAY CLUTCH DRIVE GEAR... 8-11... 8-14 8-0 Torque:
Shimano Trinidad\Torium Drag Upgrade Tutorial
Shimano Trinidad\Torium Drag Upgrade Tutorial Introduction: This tutorial is provided to assist those of you who may be interested in performing upgrade of the drag system of your Shimano Trinidad 16,
Transmission Overhaul Procedures-Bench Service
How to Assemble the Lower Reverse Idler Gear Assembly Special Instructions In 1996 Eaton changed the reverse idler system design. In the nut design, the reverse idler bearing was lubricated through a hole
Z TECHNICAL INSTRUCTIONS
ÍNDICE: Z40 2.0 TECHNICAL INSTRUCTIONS 1.- Error list 2.- Replace the control board 3.- Opening the machine 4.- Replace the power board 5.- Dismantling motor and gear box 6.- Assembly of gear box 7.- Pushing
INSPECTION ST 13 2UZ-FE STARTING STARTER. Terminal 50. Terminal C. Battery. Disconnect Battery. Terminal C. Disconnect. Battery.
2UZ-FE ARTING ARTER 13 INSPECTION 1. INSPECT ARTER ASSEMBLY NOTICE: These tests must be done within 3 to 5 seconds to avoid burning out the coil. (a) Do pull-in test. (1) Disconnect the field coil lead
Parts catalogue LAWN MOWER
OREC ISSUED NO. GR537PRO-01 Parts catalogue LAWN MOWER (EXPORT MODEL) GR537PRO(2Action) MODEL GR537PRO CODE 0268- CONTENTS TRANSMISSION ---------------------------------- 1 SAFETY COVER ----------------------------------
STARTER (for 2WD and Pre-Runner)
4 1GR-FE ARTING ARTER (for 2WD and Pre-Runner) ARTER (for 2WD and Pre-Runner) ENGINE 1GR-FE ARTING COMPONENTS 9.3 (95, 82 in.*lbf) BRUSH SPRING x4 ARTER ARMATURE ASSEMBLY O-RING O-RING ARTER YOKE ASSEMBLY
REMOVAL & INSTALLATION
Page 1 of 11 REMOVAL & INSTALLATION TIMING BELT Tips Click a link to view tip Tech1 Question: Timing problems P0340 Tech1 Question: 2.2 TIMING PROBLEMS - RESOLVED Removal Tips Click a link to view tip
STEERING COLUMN - TILT
STEERING COLUMN - TILT 1994 Toyota Celica 1994 STEERING Toyota - Steering Column - Tilt Wheel Celica DESCRIPTION & OPERATION Tilt steering wheels incorporate a mainshaft, attached by a "U" joint to an
PremAire Cadet Escape Respirator: Second Stage Regulator
PremAire Cadet Escape Respirator: Second Stage Regulator MAINTENANCE AND REPAIR MSA 115 (L) Rev. 1 MSA 2011 Prnt. Spec. 10000005389(I) Mat. 10110430 Doc. 10110430 Item P/N Description 1 697453 O-ring,
The new mechanical Hi-beat 36,000 GMT
March 27, 2014 The new mechanical Hi-beat 36,000 GMT Seiko Watch Corporation is pleased to announce the global launch of a new caliber, its first ever hi-beat GMT. Caliber 9S86 has been created on the
BASE PRESSURE AND STATIC ADJUSTMENT (COUNTERCLOCKWISE TO INCREASE)
10 INCH 6 LEVER SPECIFICATIONS AND PARTS LIST Warning: Be sure to remove the three 1/4"-20 socket head capscrews after installing the pressure plate. These keep the pressure plate from binding when removing
Dec. 2, G. DUsos ETAL 3,543,506 SELF-WINDING, WRISTWATCH WITH A CHRONOGRAPH MECHANISM INVENTORS GERALD DVBOIS PAUL MARMER.
Dec. 2, 1970 G. DUsos ETAL 3,543,506 SELF-WINDING, WRISTWATCH WITH A CHRONOGRAPH MECHANISM Filed Aug. 1, 1968 5 Sheets-Sheet INVENTORS GERALD DVBOIS PAUL MARMER 22e 24 ATTORNEYS Dec. 1, 1970 SEIF-WINDING