Repair Manual VW 02J gearbox. INA GearBOX

Size: px
Start display at page:

Download "Repair Manual VW 02J gearbox. INA GearBOX"

Transcription

1 Repair Manual VW 02J gearbox INA GearBOX

2 Special tools Pipe section, 50 mm: Press fitting of synchronizer body for third/fourth gear. Assembly of support bearing for input and output shaft. Part number: Pipe section, 60 mm: Press fitting of synchronizer body for first/second gear. Part number: Drive-in sleeve: Press fitting of needle roller bearing sleeve for fourth and fifth gear. Assembly of support bearing for input and output shaft. Part number: Press fit sleeve: Press fitting of needle roller bearing sleeve for third gear. Part number: Thrust piece: Press fitting of needle roller bearing sleeve for third gear. Assembly/disassembly of reverse gear shaft needle roller bearing. Part number: Shim set Shim set: Installation location: differential tapered roller bearing. Outside diameter of 67,9 mm Part number: Shim set: Installation location: output shaft tapered roller bearing. Outside diameter of 50,2 mm Part number: Shim set: Installation location: of input shaft tapered roller bearing. Outside diameter of 69.0 mm Part number:

3 Repair Manual for VW 02J gearbox Drain the transmission fluid (arrow). Then refit the oil drain plug. Tightening torque of oil drain plug: 25 Nm Remove the gearbox from the vehicle in accordance with the vehicle manufacturer specifications. 1 Unhook the retaining spring (arrow). Remove the release lever and release bearing. 2 Remove screws (1) from guiding sleeve. Remove the guiding sleeve. 3 3

4 Loosen the screws on the left and right driveshaft flanges. Completely remove the driveshaft flanges together with pressure spring, thrust washer and conical ring. To release, secure the driveshaft flanges with two screws and a tyre lever. 4 Remove screws (1) from transmission housing cover. Remove transmission cover. 5 4 Clean sealing surfaces. Remove screws (1) from bearing journals. Remove gear shift fork fifth gear (2). 6 Unscrew screws for synchronizer body and toothed gear fifth gear (A). 7 To undo the screws, block the transmission. To do this, press selector sleeve fifth gear (1) downwards, push in selector shaft (2) and rotate anticlockwise (3). Return the selector shaft to neutral after loosening the screws. For the neutral position, turn selector shaft clockwise until it pops out independently. 4

5 Place extractor under speed gear for fifth gear. Extract synchronizer package and speed gear from input shaft. 8 Caution: Take care when lifting out synchronizer package (selector sleeve, thrust pieces and spring lock washer) to prevent it from falling apart! Place extractor underneath toothed gear fifth gear. Remove toothed gear fifth gear. 9 Unscrew nut (1) from selector mass. Remove selector mass. 10 Remove screws from selector shaft (arrows). Remove selector shaft. Remove both bearing journals (1). 11 5

6 Remove both bearing journals (1). Undo screw on reverse gear (2). Remove cover (3). 12 Remove screw from reverse gear (arrow). 13 Remove screws (1) from transmission housing. 14 Caution: Do not unscrew bearing housing retainer nuts (2) of the output shaft. Remove screws from transmission housing. 15 6

7 Lift off transmission housing. 16 Caution: Be careful not to damage the sealing surfaces when doing this. Clean sealing surfaces. Remove gear shift forks and gear shift rails (1). Remove screw from reverse gear actuator (2). Remove reverse gear actuator. 17 Remove bearing housing retainer nuts (1) from the output shaft. 18 Remove reverse gear (1), input shaft (2) and output shaft (3) from the housing. Lift out differential (4). Remove magnet (5). 19 7

8 Pull out reverse gear drawn cup needle roller bearing with open end from housing. 20 Pull out engine-side bearing ring for input shaft. 21 Pull out engine-side bearing ring for output shaft. Remove shim. 22 Pull out engine-side bearing ring for differential. 23 8

9 Remove flanged shaft seal on the engine side. 24 Install new engine-side flanged shaft seal. 25 Clean the sealing surface before installing the new sealing ring. Adhere to nonverbal mounting instructions Pull out transmission-side bearing ring for differential. Remove shim. 26 Remove drive flange seal on the transmission side

10 Install new transmission-side flanged shaft seal. 28 Clean the sealing surface before installing the new sealing ring. Press out transmission-side bearing ring for input shaft together with shim. 29 Press out transmission-side bearing ring of output shaft. 30 Press out drawn cup needle roller bearing with open end from reverse shaft support. 31 Use special tool

11 Extract both differential bearings. 32 Remove speedometer drive. 33 Drive out roll pin in direction of arrow. 34 Drive in the new roll pin as far as it will go

12 Reassemble speedometer drive. 36 Press fit new differential bearings on both sides. 37 Adhere to nonverbal mounting instructions Press fit engine-side bearing ring for differential. 38 Press fit transmission-side bearing ring for differential. 39 First press fit bearing ring without shim. 12

13 Press off engine-side bearing of input shaft. 40 Press off transmission-side bearing of input shaft together with toothed gear for fourth gear, washer and sleeve. 41 Press fit engine-side bearing of input shaft. 42 Support bearing when press fitting onto the inner ring. Press fit the toothed gear for fourth gear 43 The shoulder on the toothed gear must point towards third gear 13

14 Press fit transmission-side bearing of input shaft. 44 Use special tool Position washer (1). Press fit sleeve (2) for needle roller bearing. 45 Use special tool Press fit drawn cup needle roller bearing with open end into reverse shaft support. 46 Press off speed gears for second to fourth gears from output shaft together with synchronizer package and sleeve (components 1-17). Lift the components together when disassembling to prevent the synchronizer package from falling apart. Remove circlip (18)

15 Press off components from output shaft through bearing housing (24). 48 Press off transmission-side bearing (25) from output shaft through inner ring. 49 Press off engine-side bearing (26) from output shaft through inner ring. 50 Press fit new engine-side bearing (26) on the output shaft through inner ring. 51 Use special tool

16 Press fit new transmission-side bearing (25) on output shaft through inner ring. 52 Position thrust washer (23) before press fitting. The heel is pointing towards the inner ring. Use special tool Press out outer ring of transmission-side bearing of output shaft from bearing housing. 53 Press fit outer ring of new transmission-side bearing of output shaft into the bearing housing. 54 Press fit new outer ring for engine-side bearing of output shaft together with 0.65 mm shim. Important for subsequent setting of output shaft! 55 Use special tool

17 Press fit new outer ring of engine-side bearing of input shaft. 56 Use special tool Press fit new drawn cup needle roller bearing with open end for reverse gear into clutch housing. 57 Use special tool Press fit new outer ring of transmission-side bearing of input shaft into transmission housing without shim. 58 Press fit roller sleeve for output shaft on transmission side. 59 Adhere to nonverbal mounting instructions

18 Secure roller sleeve in the transmission housing at three points (1) with a mandrel, with an offset of Insert differential. Attach the transmission housing. 61 Fix transmission housing in place with the screws shown. Tightening torque for cover screws: 25 Nm 62 Assemble dial gauge as shown and set to "0" with 1 mm preload. Move differential up and down, reading the clearance as you do so. Measured value mm produces the requisite thickness of the shim

19 Remove transmission housing. Pull out outer ring of transmission-side differential bearing. Insert appropriate shim and press fit outer ring again. 64 Insert output shaft. Tighten nuts for bearing housing (ct. Figure 18). Tightening torque for bearing connector nuts: 25 Nm + 90 Assemble dial gauge as shown and set to "0" with 1 mm preload. Move output shaft up and down, reading the clearance as you do so. 65 The required thickness of shim is derived from: Thickness of shim inserted for measurement (here 0.65 mm) + measured value mm. 66 Remove output shaft. Pull out outer ring of engine-side bearing of output shaft. Replace shim used for measurement with new, calculated shim. Press fit outer ring again. Insert the input shaft in the clutch cover. Reassemble the transmission housing and bolt it fully into place. Tightening torque for the housing screws: 25 Nm

20 Turn input shaft to allow the tapered roller bearings to set themselves. 68 This procedure must be repeated for each further measurement! Assemble dial gauge as shown and set to "0" with 1 mm preload. Move input shaft in the direction of the arrow, reading the clearance as you do so. Determine leveling disc according to table (page 30/31). Remove input shaft. Pull out outer ring of transmission-side bearing of input shaft. Insert leveling disc and press fit outer ring again. Repeat measuring procedure with shim press fit. The bearing play should be between 0.01 mm and 0.09 mm. 69 If no more bearing play can be measured, but the input shaft has a perceptible tilting clearance, the setting is also correct. When assembling the synchronizers, make sure that the recesses and dividers of the individual parts match. (Shown here on the example of first gear.) 70 Place inner synchro ring (1) on the speed gear for first gear. The angled dividers (A) point towards the intermediate ring (2). Position intermediate ring (2). The dividers (B) lock into place in the recesses (C) of the speed gear. Position outer synchro ring (3). The recesses (D) lock into place in the dividers (A) of the inner synchro ring (1). Position bearing housing (24), speed gear for first gear (22), needle roller bearing (21) and synchro ring (20). Press fit synchronizer body with sliding sleeve (19). 71 Use special tool Fit circlip (18). The exploded drawing shows a single synchronization. For transmissions dated after , this has been replaced with a double synchronization (see Figure 70). 20

21 Position synchro rings (15 17), speed gear for second gear (14), needle roller bearing (13) and thrust washer (12). Press fit sleeve for needle roller bearing for third gear (11) onto output shaft. 72 Use special tools and Position needle roller bearing (10), speed gear for third gear (9) and synchro ring (8). Press fit synchronizer body with sliding sleeve (7) onto output shaft. 73 Use special tool Press fit sleeve (6) for needle roller bearing for fourth gear onto output shaft. 74 Use special tool Position needle roller bearing (5), synchro ring (4), speed gear for fourth gear (3) and thrust washer (2). Press fit sleeve for needle roller bearing for fifth gear (1) onto output shaft. 75 Use special tool

22 Replace 4 sealing rings (arrows) of bearing housing. 76 Insert differential (1) and magnet (2). 77 Insert input shaft and output shaft together. 78 Tighten nuts of bearing housing (1) of output shaft. Tightening torque for bearing connector nuts: 25 Nm

23 Position reverse idler gear on drawn cup needle roller bearing with open end. 80 Insert reverse shaft with ratchet through reverse idler gear in needle roller bearing. 81 Position reverse shaft support on reverse shaft. 82 Screw the M8 x 100 mm stud bolts onto the reverse shaft support. 83 Bolts help to align the reverse shaft support during the subsequent assembly process. 23

24 Assemble shift actuating mechanism for reverse gear. Tightening torque of reverse gear screw: 25 Nm 84 Insert gear shift forks and gear shift rails. Align gear shift rails. Caution: Sliding blocks must be sitting in the grooves of the sliding sleeves. Reverse gear shift fork must be located underneath the large gear shift fork (see detailed photo). 85 Apply sealant to one side of the transmission housing. 86 Assemble transmission housing halves

25 Tighten screws for transmission housing. Tightening torque of housing screws: 25 Nm + 90 Insert side screw (1) of reverse gear and tighten by hand. Unscrew stud bolts (2) and replace with original screw. Tighten both screws one after the other. Tightening torque of screws: 30 Nm 88 Tighten housing screws (1) in the clutch bell housing. Tightening torque of housing screws: 25 Nm Clean the 4 bearing journals of the gear shift forks. Replace the o-rings of the bearing journals. 90 Install the 4 bearing journals. Tightening torque of the bearing journal screws: 25 Nm 91 If necessary, adjust the shift actuating mechanism using a screwdriver to ensure that the relevant bearing journal can be installed. 25

26 Apply sealant. 92 Put gear shift rails in neutral position. Insert lug (1) into the recess (2) of the transmission housing. Arrange selector shaft so that the shift fingers (3) can be inserted into the gear shift rails. Screw on shift actuating mechanism. Tightening torque of shift actuating mechanism screws: 25 Nm 93 Screw on selector mass. Tightening torque for flywheel mass nut: 25 Nm 94 Apply sealant

27 Attach cover. Tightening torque for cover screws: 25 Nm 96 Press fit toothed gear for fifth gear. 97 Surrounding groove must be facing the transmission! Press fit synchronizer unit for fifth gear. 98 Ensure correct assembly of synchronizer body and synchro ring! The cast-on tabs of the synchro ring (1) must be sitting in the recesses (2) of the synchronizer body. Fasten synchronizer unit and toothed gear for fifth gear with respective spring washer and screw (A). Tightening torque of screws: 80 Nm 99 To tighten the screws, block the transmission. To do this, press selector sleeve fifth gear (1) downwards, push in selector shaft (2) and rotate anti-clockwise (3). Return the selector shaft to neutral after tightening the screws. For the neutral position, turn selector shaft clockwise until it pops out independently. 27

28 Assemble gear shift fork. fifth gear should be engaged using selector shaft. Loosen screw of selector jaws (1). Push sliding sleeve and selector jaws downwards. Tighten screw of selector jaws (1). Tightening torque for screw of selector jaws: 25 Nm 100 Perform control measurement: It must not be possible to insert a feeler gauge of 0.2 mm in between the sliding sleeve and ratchet. Repeat the adjustment procedure, if required. fifth gear should be removed using the selector shaft: The sliding sleeve must now be in the neutral position, synchro ring for fifth gear must move freely. Shift through all gears. 101 Replace the cover seal. 102 Put cover of transmission housing into position

29 Tighten cover screws (1). Tightening torque for cover screws: 10 Nm 104 Push new guiding sleeve onto the input shaft. Tighten screws (1). Tightening torque of mounting screws: 20 Nm Grease sleeve in area of release bearing. 105 Fasten the retaining spring to the clutch release lever. Install clutch release lever. Mount the retaining spring. Grease release bearing at contact point with release lever and push into place. 106 Install both driveshaft flanges using springs, thrust washers and conical rings. Tightening torque for the flange screws: 25 Nm

30 Install the transmission in the vehicle in accordance with the manufacturer's instructions. Fill with transmission fluid in accordance with the vehicle manufacturer's specifications. 108 Setting the input shaft tapered roller bearing Table of shims Part number for shim set: Bearing play Shim Measured value (mm) Thickness (mm) Spare part no A A A A B A C A D A E A F A G A H A J A K A L A M A N A P A Q A R A S A T A AA A AB A AC A AD A AE A AF A AG 30

31 Setting the input shaft tapered roller bearing Table of shims Part number for shim set: From bearing play greater than mm, a combination of two shims may be required. Bearing play Shim Measured value (mm) Thickness (mm) Spare part no A A A A A A A 02A A A A 02A B A B 02A B A B 02A C A C 02A C A C 02A D A D 02A D A D 02A E A E 02A E A E 02A F A F 02A F A F 02A G A G 02A G A G 02A H A H 02A H A H 02A J A J 02A J 31

32 Optional sender details (highlighted) Optional sender details (2nd line of text) Optional sender details (3rd line of text) *optional subline with legal text / Schaeffler Automotive Aftermarket

LuK Repair Solution for manual transmissions. Disassembly and assembly Special tool/failure diagnosis VW 02J

LuK Repair Solution for manual transmissions. Disassembly and assembly Special tool/failure diagnosis VW 02J LuK Repair Solution for manual transmissions Disassembly and assembly Special tool/failure diagnosis VW 02J The content of this brochure shall not be legally binding and is for information purposes only.

More information

PSA MA gearbox. INA GearBOX

PSA MA gearbox. INA GearBOX LuK Repair Tractor Manual Clutches PSA MA gearbox INA GearBOX Repair Manual for the PSA MA gearbox Drain the transmission fluid (arrow). Remove the gearbox from the vehicle in accordance with the vehicle

More information

Repair Manual VW 02T gearbox. INA GearBOX

Repair Manual VW 02T gearbox. INA GearBOX Repair Manual VW 02T gearbox INA GearBOX Special tools Repair Manual for the VW 02T gearbox Drain the transmission fluid (arrow). Remove the gearbox from the vehicle in accordance with the vehicle manufacturer

More information

LuK Repair Solution for manual transmissions. Disassembly and assembly Special tool/failure diagnosis PSA MA

LuK Repair Solution for manual transmissions. Disassembly and assembly Special tool/failure diagnosis PSA MA LuK Repair Solution for manual transmissions Disassembly and assembly Special tool/failure diagnosis PSA MA The content of this brochure shall not be legally binding and is for information purposes only.

More information

Repair Manual Ford DPS6 Gearbox. INA GearBOX

Repair Manual Ford DPS6 Gearbox. INA GearBOX Repair Manual Ford DPS6 Gearbox INA GearBOX Special Tools Tool kit (400 0477 10) for professional repair of the Ford DPS6 gearbox. Assembly table: Table (A) for securing the shafts, gear shift positions

More information

Output Shaft Assembly COMPONENTS

Output Shaft Assembly COMPONENTS MT140 Component Parts (Output Shaft Assembly Output Shaft Assembly COMPONENTS DISASSEMBLY OF OUTPUT SHAFT ASSEMBLY 1. REMOVE SLEEVE FROM OUTPUT SHAFT Using SST, remove the sleeve from the output shaft.

More information

Model 4360 Teardown and Reassembly Instructions

Model 4360 Teardown and Reassembly Instructions Clean the outside surface of the transaxle. Place the shifter in neutral position. Remove detent cover screw (item 3), detent cover (item 4), detent springs (item 5), and detent balls (item 6). Use a magnet

More information

MANUAL TRANSAXLE Return to Main Table of Contents

MANUAL TRANSAXLE Return to Main Table of Contents MANUAL TRANSAXLE Return to Main Table of Contents GENERAL... 2 MANUAL TRANSAXLE CONTROL... 12 SHIFT LEVER ASSEMBLY... 14 MANUAL TRANSAXLE... 15 MANUAL TRANSAXLE ASSEMBLY... 17 FIFTH SPEED SYNCHRONIZER

More information

The 6-Speed Manual Gearbox 08D

The 6-Speed Manual Gearbox 08D Service. Self-Study Programme 299 The 6-Speed Manual Gearbox 08D Design and Function The Touareg is an exclusive cross country vehicle with the driving properties and driving comfort of a sporty luxury

More information

SECTION 5B MANUAL TRANSMISSION TABLE OF CONTENTS

SECTION 5B MANUAL TRANSMISSION TABLE OF CONTENTS SECTION 5B MANUAL TRANSMISSION TABLE OF CONTENTS General Description and Operation... 5B-2 Shift Lever... 5B-2 Transmission Assembly... 5B-2 Specifications... 5B-3 Diagnostic Information and Procedures...

More information

Repairs after which the ring gear must be adjusted Page Drift VW 295

Repairs after which the ring gear must be adjusted Page Drift VW 295 Page 1 of 15 39-52 Ring gear, adjusting (Adjusting differential) Repairs after which the ring gear must be adjusted Page 39-37. Special tools, testers and auxiliary items Drift VW 295 Dial gauge extension

More information

70001 and Clutch Rebuild Instructions

70001 and Clutch Rebuild Instructions 70001 and 70010 Clutch Rebuild Instructions Brinn, Incorporated 1615 Tech Drive Bay City, MI 48706 Telephone 989.686.8920 Fax 989.686.6520 www.brinninc.com Notice Use these instructions if you only want

More information

1. General Description

1. General Description 1. General Description A: SPECIFICATIONS 1. Type Transmission gear ratio Front reduction gear Rear reduction gear 2. TRANSMISSION GEAR OIL Recommended oil Final Transfer 5-forward speeds with synchromesh

More information

DRIVE AXLE Volvo 960 DESCRIPTION & OPERATION AXLE IDENTIFICATION DRIVE AXLES Volvo Differentials & Axle Shafts

DRIVE AXLE Volvo 960 DESCRIPTION & OPERATION AXLE IDENTIFICATION DRIVE AXLES Volvo Differentials & Axle Shafts DRIVE AXLE 1994 Volvo 960 1994 DRIVE AXLES Volvo Differentials & Axle Shafts 960 DESCRIPTION & OPERATION All 960 station wagon models use type 1041 rear axle assembly. All 960 4-door models use type 1045

More information

Reverse Idler Gear Shaft

Reverse Idler Gear Shaft «1993 Thunderbird/Cougar Table of Contents» «Group 07: TRANSMISSION» «Section 07-03: Transmission, Manual--M5R2» «DISASSEMBLY AND ASSEMBLY» Reverse Idler Gear Shaft Disassembly Remove the following parts

More information

SISU DP-330 DRIVE GEAR. Maintenance Manual

SISU DP-330 DRIVE GEAR. Maintenance Manual SISU DP-330 DRIVE GEAR Maintenance Manual Sisu Axles, Inc. Autotehtaantie 1 PO Box 189 Fin-13101 Hameenlinna Finland Phone +358 204 55 2999 Fax +358 204 55 2900 DP330DG.PDF (3/2007) TABLE OF CONTENTS

More information

HOLINGER SF GEARBOX MANUAL

HOLINGER SF GEARBOX MANUAL HOLINGER SF GEARBOX MANUAL Approved By: Leigh Nash Date: 26/05/2011 Rev: D Date: 11/11 Holinger Engineering Gearbox Manual Page 1 FOREWORD The Holinger SF is a sequential-shift transaxle designed for use

More information

1. General Description

1. General Description 1. General Description A: SPECIFICATION 1. MANUAL TRANSMISSION AND FRONT DIFFERENTIAL Type Transmission gear ratio Front reduction gear Rear reduction gear Front differential Center differential Final

More information

Differential, Disassembling and Assembling Special tools

Differential, Disassembling and Assembling Special tools Differential, Disassembling and Assembling Special tools VAG 1582 Bearing puller VAG 1582/3 Grip piece VW 412 Thrust disc 40-105 Thrust piece VW 401 Thrust plate VW 402 Thrust plate VW 408 A Punch VW 473

More information

MANUAL TRANS OVERHAUL - BORG-WARNER - T56 6-SPEED MANUAL TRANSMISSIONS Borg-Warner T56 (MM6) 6-Speed

MANUAL TRANS OVERHAUL - BORG-WARNER - T56 6-SPEED MANUAL TRANSMISSIONS Borg-Warner T56 (MM6) 6-Speed IDENTIFICATION MANUAL TRANS OVERHAUL - BORG-WARNER - T56 6-SPEED 1998 MANUAL TRANSMISSIONS Borg-Warner T56 (MM6) 6-Speed Transmission has 2 identification labels, located on lower left side of case. One

More information

Transmission, disassembling and assembling

Transmission, disassembling and assembling Page 1 of 27 34-43 Transmission, disassembling and assembling Disassembly sequence Page 34-55. Transmission overview 1-1st gear 2-2nd gear 3-3rd gear 4-4th gear 5-5th gear 6 - Reverse gear Removing and

More information

26 Hume Reserve Court, Nth. Geelong, 3215 Phone: (03) Fax: (03) DUAL RANGE HIGH SPEED INSTALLATION MANUAL. for

26 Hume Reserve Court, Nth. Geelong, 3215 Phone: (03) Fax: (03) DUAL RANGE HIGH SPEED INSTALLATION MANUAL. for 26 Hume Reserve Court, Nth. Geelong, 3215 Phone: (03) 5272 2844 Fax: (03) 5272 2633 GEARLESS CENTRE DIFFERENTIAL FULL-TIME 4X4 TRANSFER CASE CONVERSION DUAL RANGE HIGH SPEED INSTALLATION MANUAL for TOYOTA

More information

1994 Mitsubishi Eclipse GS

1994 Mitsubishi Eclipse GS APPLICATIONS CHRYSLER MOTORS MANUAL TRANS OVERHAUL - MITSUBISHI W5M & W6M SERIES MANUAL TRANSMISSIONS Mitsubishi W5M31, TRANSMISSION APPLICATIONS (CHRYSLER MOTORS) Vehicle Application Transmission Model

More information

TSM54/52 MANUAL TRANSMISSION

TSM54/52 MANUAL TRANSMISSION 3B-1 SECTION 00 3B TSM54/52 MANUAL TRANSMISSION Table of Contents GENERAL INFORMATION... 3B-3 Overview... 3B-3 Specifications... 3B-4 System components... 3B-5 Shifting mechanism... 3B-17 Diagnostic information

More information

MANUAL TRANSMISSIONS Mitsubishi F4M20, F5M20, F5M30 & KM200 Series TRANSMISSION APPLICATION

MANUAL TRANSMISSIONS Mitsubishi F4M20, F5M20, F5M30 & KM200 Series TRANSMISSION APPLICATION Article Text ARTICLE BEGINNING MANUAL TRANSMISSIONS Mitsubishi F4M20, F5M20, F5M30 & KM200 Series APPLICATION TRANSMISSION APPLICATION Vehicle Application Transmission Model Chrysler Motors (2WD) 4-Speed

More information

SECTION B Manual Transaxle/Transmission TR6060

SECTION B Manual Transaxle/Transmission TR6060 308-03B-i Manual Transaxle/Transmission TR6060 308-03B-i SECTION 308-03B Manual Transaxle/Transmission TR6060 CONTENTS PAGE Transmission... 308-03B-2 308-03B-2 Manual Transaxle/Transmission TR6060 308-03B-2

More information

DRIVE AXLE - INTEGRAL HOUSING

DRIVE AXLE - INTEGRAL HOUSING DRIVE AXLE - INTEGRAL HOUSING 1993 Toyota Celica 1993 DRIVE AXLES Toyota Differentials & Axle Shafts - Integral Housing Toyota; Celica All-Trac DESCRIPTION Drive axle assembly is a hypoid type with integral

More information

Dismantling and assembling transmission

Dismantling and assembling transmission 27-640 Dismantling and assembling transmission Operation number of the operation texts and work units or standard texts and flat rates: 27-4010 P27-5367-61 Control pressure cable (98) Slacken, remove and

More information

SISU MP-330 DRIVE GEAR. Maintenance Manual

SISU MP-330 DRIVE GEAR. Maintenance Manual SISU MP-330 DRIVE GEAR Maintenance Manual Sisu Axles, Inc. Autotehtaantie 1 PO Box 189 Fin-13101 Hameenlinna Finland Phone +358 204 55 2999 Fax +358 204 55 2900 MP330DG.PDF (4/2007) TABLE OF CONTENTS

More information

A 1 SERVICE SPECIFICATIONS

A 1 SERVICE SPECIFICATIONS A1 A2 Clutch CLUTCH Specifications Pedal height (from asphalt sheet) Release point (from pedal stroke end position) Push rod play at pedal top Pedal freeplay Disc rivet head depth Disc runout Diaphragm

More information

DISASSEMBLY AND ASSEMBLY

DISASSEMBLY AND ASSEMBLY 205-03-1 Front Drive Axle/Differential Ford 8.8-Inch Ring Gear 205-03-1 DISASSEMBLY AND ASSEMBLY Axle Front Drive Special Tool(s) 2-Jaw Puller 205-D072 (D97L-4221-A) Special Tool(s) Carrier Bearing Replacer

More information

Group 1: Gearbox housing

Group 1: Gearbox housing 1 Five-Speed gearbox crown wheel 11 Nylon socket for speed- 21 Screw 31 Tube 2 Plug 12 Cup 22 Screw 32 Deflector 3 Gearbox and clutch housing 13 Pinion f. speedometer 23 Screw 33 s 4 Front cover 14 Stop

More information

26 Hume Reserve Court, Nth. Geelong, 3215 Phone: (03) Fax: (03) INSTALLATION MANUAL. for

26 Hume Reserve Court, Nth. Geelong, 3215 Phone: (03) Fax: (03) INSTALLATION MANUAL. for 26 Hume Reserve Court, Nth. Geelong, 3215 Phone: (03) 5272 2844 Fax: (03) 5272 2633 GEARLESS CENTRE DIFFERENTIAL FULL-TIME 4X4 TRANSFER CASE CONVERSION DEDICATED LOW RANGE INSTALLATION MANUAL for TOYOTA

More information

LT230T TRANSFER GEARBOX. Overhaul Manual LT230T. Verdeelbak revisieboek LT230T. Boîte de transfert Manuel de révision LT230T

LT230T TRANSFER GEARBOX. Overhaul Manual LT230T. Verdeelbak revisieboek LT230T. Boîte de transfert Manuel de révision LT230T LT230T TRANSFER GEARBOX Overhaul Manual LT230T Verdeelbak revisieboek LT230T Boîte de transfert Manuel de révision LT230T Verteilergetriebe Überholungsanleitung LT230T Riduttore Manuale di revisione LT230T

More information

Further information: Phone: Schaeffler Automotive Aftermarket

Further information:   Phone: Schaeffler Automotive Aftermarket Further information: www.repxpert.de Phone: +49 6103 753-333 www.schaeffler-aftermarket.de 999 6006 570_08.2015 2015 Schaeffler Automotive Aftermarket LuK repair solution for dry double clutches Disassembly

More information

LoMax 205 CASE & 3:1 GEAR SET. Manufactured by JB CONVERSIONS, INC. Phone: Installation Instructions for the GM NP205 Transfer Case

LoMax 205 CASE & 3:1 GEAR SET. Manufactured by JB CONVERSIONS, INC. Phone: Installation Instructions for the GM NP205 Transfer Case LoMax 205 CASE & 3:1 GEAR SET Part No. 2800 Instruction Rev: 2007.08.16 Manufactured by JB CONVERSIONS, INC. Phone: Installation Instructions for the GM NP205 Transfer Case Kit Components: 1. (1) 42x25

More information

SUZUKI SQ 416/420/625 M.Y TRANSMISSION SERVICE MANUAL - MANUAL - AUTOMATIC - TRANSFER - DIFFERENTIALS

SUZUKI SQ 416/420/625 M.Y TRANSMISSION SERVICE MANUAL - MANUAL - AUTOMATIC - TRANSFER - DIFFERENTIALS SUZUKI SQ 416/420/625 M.Y 1998-2005 TRANSMISSION SERVICE MANUAL - MANUAL - AUTOMATIC - TRANSFER - DIFFERENTIALS WARNING/CAUTION/NOTE IMPORTANT Please read this manual and follow its instructions carefully.

More information

Dismantling and assembling automatic transmission (A5S560Z) (transmission removed)

Dismantling and assembling automatic transmission (A5S560Z) (transmission removed) 24 00 585 Dismantling and assembling automatic transmission (A5S560Z) (transmission removed) Secure transmission to assembly frame with special tool 24 0 180. Drain off transmission oil. Screw special

More information

Volkswagen New Beetle 2.0 Liter 4-cyl General, Engine (Engine Code AEG) 13 Engine-Crankshaft, Cylinder block (Page GR-13)

Volkswagen New Beetle 2.0 Liter 4-cyl General, Engine (Engine Code AEG) 13 Engine-Crankshaft, Cylinder block (Page GR-13) 13 Engine-Crankshaft, Cylinder block (Page GR-13) Engine, disassembly and assembly 10-222 A/21 guide from 10-222 A support tool, modifying Ribbed belt, removing and installing Semi-automatic toothed belt

More information

MAINTENANCE MANUAL DP-265

MAINTENANCE MANUAL DP-265 MAINTENANCE MANUAL DP-265 Drive Gears Sisu Axles, Inc. Autotehtaantie 1 P.O. Box 189 FIN-13101 Hämeenlinna Finland Phone int + 358 204 55 2999 Fax int + 358 204 55 2900 DP265DG.PDF (2/2003) k Table of

More information

DISASSEMBLY AND ASSEMBLY (Continued)

DISASSEMBLY AND ASSEMBLY (Continued) 205-03-23 Front Drive Axle/Differential Ford 8.8-Inch Ring Gear 205-03-23 49. Measure the ring gear backlash at four places to obtain a consistent reading. 1 Mount the special tools on the indicator base.

More information

Transmission Overhaul Procedures-Bench Service

Transmission Overhaul Procedures-Bench Service How to Assemble the Lower Reverse Idler Gear Assembly Special Instructions In 1996 Eaton changed the reverse idler system design. In the nut design, the reverse idler bearing was lubricated through a hole

More information

General repair instructions

General repair instructions Page 1 of 10 00-10 The maximum possible care, cleanliness and proper tools are essential to ensure satisfactory and successful transmission repairs. The usual basic safety precautions also apply when carrying

More information

Maintenance Manual FP-330 Drive Gear

Maintenance Manual FP-330 Drive Gear Maintenance Manual FP-330 Drive Gear Sisu Axles, Inc. Autotehtaantie 1 P.O. Box 189 FIN-13101 Hämeenlinna Finland Phone int + 358 204 55 2999 Fax int + 358 204 55 2900 FP330DG 2/2008 Maintenance Manual

More information

1999 F-150/250 Workshop Manual

1999 F-150/250 Workshop Manual Page 1 of 30 SECTION 205-03: Front Drive Axle/Differential Ford 8.8-Inch Ring Gear 1999 F-150/250 Workshop Manual DISASSEMBLY AND ASSEMBLY Procedure revision date: 01/08/2003 Axle Front Drive Special Tool(s)

More information

2001 Dodge RAM 3500 PICKUP

2001 Dodge RAM 3500 PICKUP 1 of 76 9/14/2012 7:02 PM 2001 Dodge RAM 3500 PICKUP Submodel: Engine Type: L6 Liters: 5.9 Fuel Delivery: FI Fuel: DIESEL Subarticles MANUAL- NV3500 - DISASSEMBLY MANUAL- NV3500 - DISASSEMBLY MANUAL -

More information

Technical Information Review

Technical Information Review Technical Information Review While every attempt is made to ensure that the technical information we supply is as accurate and up to date as possible, from time to time, errors do occur. There may also

More information

DRIVE AXLE Nissan 240SX DESCRIPTION & OPERATION AXLE RATIO & IDENTIFICATION AXLE SHAFT & BEARING R & I DRIVE SHAFT R & I

DRIVE AXLE Nissan 240SX DESCRIPTION & OPERATION AXLE RATIO & IDENTIFICATION AXLE SHAFT & BEARING R & I DRIVE SHAFT R & I DRIVE AXLE 1990 Nissan 240SX 1990 DRIVE AXLES Rear Axle - R200 240SX, 300ZX DESCRIPTION & OPERATION The axle assembly is a hypoid type gear with integral carrier housing. The pinion bearing preload adjustment

More information

Disassembling and assembling transmission

Disassembling and assembling transmission 27-640 Disassembling and assembling transmission Preceding work: Removing and installing transmission with torque converter (27-600). Operation number of operation texts and operation values or standard

More information

Page 1 of 15 Transmission, Model S5-42 ZF Model S5-42 ZF Disassembly NOTE: For 4x4 and F-Super Duty vehicles, skip to Step 5. 1. Attach the transmission to the Bench Mounted Holding Fixture T57L-500-B

More information

G Class Transfer Case. 217 HO 06 Transfer Case (IC GC OP TF)

G Class Transfer Case. 217 HO 06 Transfer Case (IC GC OP TF) G Class Transfer Case 217 HO 06 Transfer Case (IC GC OP TF) 1-30-03 2 These technical training materials are current as of the date noted on the materials, and may be revised or updated without notice.

More information

SECTION 7B3 - MANUAL TRANSMISSION - GEN III V8 ENGINE

SECTION 7B3 - MANUAL TRANSMISSION - GEN III V8 ENGINE SECTION 7B3 - MANUAL TRANSMISSION - GEN III V8 ENGINE CAUTION: This vehicle will be equipped with a Supplemental Restraint System (SRS). An SRS will consist of either seat belt pre-tensioners and a driver's

More information

Manual Transmission (M2S5,M3S5) General Troubleshooting... MTA - 2 Specification... MTA - 9

Manual Transmission (M2S5,M3S5) General Troubleshooting... MTA - 2 Specification... MTA - 9 Manual Transmission (M2S5,M3S5) General Troubleshooting... MTA - 2 Specification... MTA - 9 Manual Transmission Description and Operation... MTA - 13 Components... MTA - 19 Inspection... MTA - 20 Removal...

More information

AUTOMATIC TRANSMISSIONS Mitsubishi F3A20 Series TRANSMISSION APPLICATION TABLE

AUTOMATIC TRANSMISSIONS Mitsubishi F3A20 Series TRANSMISSION APPLICATION TABLE Article Text ARTICLE BEGINNING AUTOMATIC TRANSMISSIONS Mitsubishi F3A20 Series APPLICATION TRANSMISSION APPLICATION TABLE Vehicle Application Transmission Model Colt 3-Speed (1990-94)... F3A21 Colt Vista

More information

MANUAL TRANSMISSION F5M41, F5M42, W5M42 CONTENTS GENERAL INFORMATION 1. SPECIFICATIONS... 22B-1-1 TRANSMISSION MODEL TABLE

MANUAL TRANSMISSION F5M41, F5M42, W5M42 CONTENTS GENERAL INFORMATION 1. SPECIFICATIONS... 22B-1-1 TRANSMISSION MODEL TABLE 22B-0-1 MANUAL TRANSMISSION F5M41, F5M42, W5M42 GENERAL INFORMATION........................................... 22B-0-3 1. SPECIFICATIONS................................................. 22B-1-1 TRANSMISSION

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION AXLE SHAFTS & BEARINGS Removal CAUTION: Failure to turn off air suspension power before raising vehicle may result in unexpected inflation or deflation of air springs. DO NOT reconnect

More information

MANUAL TRANSAXLE SECTIONMT CONTENTS IDX. Shift Control Components...34

MANUAL TRANSAXLE SECTIONMT CONTENTS IDX. Shift Control Components...34 MANUAL TRANSAXLE SECTIONMT GI MA EM LC EC CONTENTS FE PREPARATION...3 Special Service Tools...3 Commercial Service Tools...5 NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING...6 NVH Troubleshooting

More information

INSTRUCTIONS. Disassembly. Shifter Cam Assembly. Shifter Forks

INSTRUCTIONS. Disassembly. Shifter Cam Assembly. Shifter Forks INSTRUCTIONS Disassembly To protect against accidental start-up of vehicle, always disconnect the negative battery cable before working on the motorcycle. Failure to disconnect the battery cable could

More information

Page 1 of 22 SECTION 307-01: Automatic Transaxle/Transmission 4R70E/4R75E ASSEMBLY Procedure revision date: 05/29/2009 Transmission Printable View (1554 KB) Special Tool(s) Air Test Plate, Transmission

More information

Inspection and Verification, Ranger

Inspection and Verification, Ranger file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svk53a03.htm~gen~ref.htm Page 1 of 1 Section 05-03A: Wheel Hubs and Bearings, Front Wheels, 4- Wheel Drive DIAGNOSIS AND TESTING 1997 Ranger 4x4 with Dana

More information

Sealing flanges and flywheel/drive plate, removing and installing

Sealing flanges and flywheel/drive plate, removing and installing Page 1 of 20 13-47 Sealing flanges and flywheel/drive plate, removing and installing Note: For repairs to the clutch: Repair Manual, 5 Spd. Manual Transmission 012/01W Front Wheel Drive, Repair Group 30

More information

TRANSFER CASE Mitsubishi Montero APPLICATION DESCRIPTION TESTING 4WD INDICATOR CONTROL UNIT (MONTERO) DETECTION SWITCH

TRANSFER CASE Mitsubishi Montero APPLICATION DESCRIPTION TESTING 4WD INDICATOR CONTROL UNIT (MONTERO) DETECTION SWITCH TRANSFER CASE 1993 Mitsubishi Montero 1991-94 TRANSFER CASES Mitsubishi Dodge; Ram-50 Mitsubishi; Pickup, Montero APPLICATION TRANSFER CASE APPLICATIONS TABLE Application (1) Transmission Model Dodge 1991-93

More information

2003 E-Series Workshop Manual

2003 E-Series Workshop Manual Page 1 of 20 SECTION 307-01B: Automatic Transmission 4R70W 2003 E-Series Workshop Manual ASSEMBLY Procedure revision date: 04/27/2006 Transmission Printable View (1828 KB) Special Tool(s) Dial Indicator

More information

FRONT AXLE 26-1 CONTENTS GENERAL INFORMATION... 2 HUB AND KNUCKLE ASSEMBLY SERVICE SPECIFICATIONS... 4 DRIVE SHAFT LUBRICANTS...

FRONT AXLE 26-1 CONTENTS GENERAL INFORMATION... 2 HUB AND KNUCKLE ASSEMBLY SERVICE SPECIFICATIONS... 4 DRIVE SHAFT LUBRICANTS... 26-1 FRONT AXLE CONTENTS GENERAL INFORMATION.................. 2 SERVICE SPECIFICATIONS................. 4 LUBRICANTS.............................. 4 SEALANTS AND ADHESIVES.............. 5 SPECIAL TOOLS...........................

More information

MANUAL TRANSMISSION MUA 5C (4X2, 4X4) AND TREMEC T5R(4X2)

MANUAL TRANSMISSION MUA 5C (4X2, 4X4) AND TREMEC T5R(4X2) MANUAL TRANSMISSION 7B 1 RODEO TRANSMISSION MANUAL TRANSMISSION MUA 5C (4X2, 4X4) AND TREMEC T5R(4X2) CONTENTS Service Precaution...................... 7B 2 General Description..................... 7B

More information

Technical Note6019A X61, and TL4 - X77, and TL4 - X84, and TL4 - X85, and TL4 - X91, and TL4 - X95, and TL4 TL4 manual gearbox

Technical Note6019A X61, and TL4 - X77, and TL4 - X84, and TL4 - X85, and TL4 - X91, and TL4 - X95, and TL4 TL4 manual gearbox Technical Note6019A X61, and TL4 - X77, and TL4 - X84, and TL4 - X85, and TL4 - X91, and TL4 - X95, and TL4 TL4 manual gearbox Edition 9 77 11 335 822 APRIL 2009 Edition Anglaise "The repair methods given

More information

DF 15. DIFFERENTIAL 1GR-FE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD) REMOVAL

DF 15. DIFFERENTIAL 1GR-FE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD) REMOVAL DIFFERENTIAL 1GR-FE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD) 15 REMOVAL 1. REMOVE FRONT WHEELS 2. REMOVE REAR ENGINE UNDER COVER ASSEMBLY (a) Remove the 6 bolts and engine under cover assembly. 3.

More information

TRANSMISSION 6.7 GENERAL HOME. See Figure The transmission is a five-speed constantmesh type housed in an extension of the crankcase.

TRANSMISSION 6.7 GENERAL HOME. See Figure The transmission is a five-speed constantmesh type housed in an extension of the crankcase. TRANSMISSION 6.7 GENERAL See Figure 6-46. The transmission is a five-speed constantmesh type housed in an extension of the crankcase. b06x6x Neutral st Gear Mainshaft Mainshaft 4 5 4 5 Countershaft Out

More information

Chapter 3. Power train

Chapter 3. Power train Chapter 3. Power train Clutch The design of the clutch is shown on fig. 3-1. The clutch release fork 11 (fig. 3-1) can be of two types: with a leaf or wire spring. Fig. 3-1. Clutch assembly: 1 - bleeder;

More information

FRONT AXLE Click on the applicable bookmark to selected the required model year

FRONT AXLE Click on the applicable bookmark to selected the required model year FRONT AXLE 26-1 FRONT AXLE CONTENTS GENERAL INFORMATION.................. 2 SERVICE SPECIFICATIONS................. 4 LUBRICANTS.............................. 4 SEALANTS AND ADHESIVES.............. 5 SPECIAL

More information

6-speed manual gearbox 0A5

6-speed manual gearbox 0A5 Service Training Self-study programme 320 6-speed manual gearbox 0A5 Design and function S320_002 In addition to meeting increasing technical demands, modern cars also have to represent effective space

More information

WORKSHOP MANUAL TECHNICAL NETWORK LEADERSHIP WORKSHOP MANUAL 125 CC/150 CC 4-STROKE ENGINE

WORKSHOP MANUAL TECHNICAL NETWORK LEADERSHIP WORKSHOP MANUAL 125 CC/150 CC 4-STROKE ENGINE WORKSHOP MANUAL TECHNICAL NETWORK LEADERSHIP WORKSHOP MANUAL - 5 CC/50 CC 4-STROKE ENGINE Workshop manual Technical network leadership TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS... CHARACTERISTICS...

More information

Transmission Overhaul Procedures-Bench Service

Transmission Overhaul Procedures-Bench Service How to Install the Auxiliary Countershaft Assembly Special Instructions To make auxiliary section assembly easier, you can make an auxiliary section fixture out of a 2" x 12" piece of wood. 3' 1' 3" 4.56"

More information

Removing and installing cylinder head

Removing and installing cylinder head 31 30 29 28 27 26 25 24 23 22 1 2 3 11 12 10 4 9 5 6 7 8 Removing and installing cylinder head Checking compression pressure page 15-24. Notes: When installing a replacement cylinder head with a mounted

More information

TRANSMISSION 6.7 GENERAL HOME. See Figure The transmission is a five-speed constantmesh type housed in an extension of the crankcase.

TRANSMISSION 6.7 GENERAL HOME. See Figure The transmission is a five-speed constantmesh type housed in an extension of the crankcase. TRANSMISSION 6.7 GENERAL See Figure 6-45. The transmission is a five-speed constantmesh type housed in an extension of the crankcase. Mainshaft Neutral Mainshaft st Gear b06x6x Countershaft 4 Out 5 Countershaft

More information

1. Spare Parts List 1.1 Preface The spare parts list is only valid for the type and versions of transmission, as shown below. You will find the transm

1. Spare Parts List 1.1 Preface The spare parts list is only valid for the type and versions of transmission, as shown below. You will find the transm S P A R E P A R T S L I S T A N D E X P L O S I O N V I E W P A S C A T A L O G U E R T R E A S P ZF 15 MIV (HBW 150 V) Cod. 310.01.0100 1. Spare Parts List 1.1 Preface The spare parts list is only valid

More information

WORKSHEET 4-1 Transaxle Case Removal and Component Identification

WORKSHEET 4-1 Transaxle Case Removal and Component Identification WORKSHEET 4-1 Transaxle Case Removal and Component Identification Vehicle: Year/Prod. Date: Engine Transmission: Worksheet Objectives With this worksheet, you will follow the disassembly of a front-drive

More information

DESCRIPTION AND OPERATION. Description

DESCRIPTION AND OPERATION. Description file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svk73001.htm~gen~ref.htm Page 1 of 1 Section 07-03: Transmission, Manual, M5OD DESCRIPTION AND OPERATION 1997 Ranger Workshop Manual Description The M5OD

More information

X-Trainer 43mm fork service manual. Beta USA, Inc This work should be performed by a trained motorcycle technician.

X-Trainer 43mm fork service manual. Beta USA, Inc This work should be performed by a trained motorcycle technician. X-Trainer 43mm fork service manual Beta USA, Inc. 2016 This work should be performed by a trained motorcycle technician. Table of contents Page Introduction/special tools... 2 Fork exploded view... 3 Legend.

More information

This file is available for free download at

This file is available for free download at This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing

More information

Geo Prizm ( LSi) Toyota Celica 1.8L (1994)

Geo Prizm ( LSi) Toyota Celica 1.8L (1994) Page 1 of 140 ARTICLE BEGINNING APPLICATION TRANSMISSION APPLICATIONS Application Geo Prizm (1993-94 LSi) Toyota Celica 1.6L (1993) Celica 1.8L (1994) Celica 2.2L (1993) Corolla 1.8L MR2 Paseo Transaxle

More information

DISASSEMBLY. Transmission. 2. Remove the 4 clutch housing bolts. Separate the clutch housing from the transmission.

DISASSEMBLY. Transmission. 2. Remove the 4 clutch housing bolts. Separate the clutch housing from the transmission. 308-03A-1 DISASSEMBLY Transmission 308-03A-1 Special Tool(s) Puller, Bearing 205-D064 (D84L-1123-A) or equivalent Remover/Installer, Front Wheel Hub 204-069 (T81P-1104-C) 2. Remove the 4 clutch housing

More information

Final drive gear set, recommended sequence for adjusting

Final drive gear set, recommended sequence for adjusting Page 1 of 31 39-148 Final drive gear set, recommended sequence for adjusting If the pinion shaft and ring gear have to be readjusted, the following sequence is recommended for maximum efficiency: 1.) Determine

More information

TRANSMISSION AND TRANSFER CASE

TRANSMISSION AND TRANSFER CASE TRANSMISSION AND TRANSFER CASE 21-1 TRANSMISSION AND TRANSFER CASE CONTENTS page page AUTOMATIC TRANSMISSION-30/32RH...... 71 MANUAL TRANSMISSION-AX5............. 1 MANUAL TRANSMISSION-AX15...........

More information

Transaxle. 1. Mount the transaxle to Bench Mounted Holding Fixture T57L-500-B.

Transaxle. 1. Mount the transaxle to Bench Mounted Holding Fixture T57L-500-B. «1997 Aspire Table of Contents» «Group 07: TRANSAXLE» «Section 07-01: Transaxle, Automatic» «DISASSEMBLY» Transaxle CAUTION: To prevent dirt from entering the transaxle, it should be disassembled and kept

More information

Transmission Disassembly

Transmission Disassembly TRANSMISSION SYSTEM F8B( 800 CC Car) Transmission system Components Name Transmission Disassembly Shifting Shaft & Fork TRANSMISSION ASSY: M/T The transmission provides four forward speeds and one reverse

More information

Workshop Bulletin LAND ROVER. D lvid E D -CASE GEARBOX. band Rover Range Rover DECEMBER BULLETIN No. SLR 621 EN WB 3

Workshop Bulletin LAND ROVER. D lvid E D -CASE GEARBOX. band Rover Range Rover DECEMBER BULLETIN No. SLR 621 EN WB 3 J band Rover Range Rover Workshop Bulletin -\,.: -*a. I ATTENTION SERVICE MANAGER DECEMBER 1987 BULLETIN No. SLR 621 EN WB 3 LAND ROVER 1,, i LT85 LIGHTWEIGHT D lvid E D -CASE GEARBOX Further supplies

More information

2005 Toyota RAV AUTOMATIC TRANSMISSIONS U240E & U241E Overhaul

2005 Toyota RAV AUTOMATIC TRANSMISSIONS U240E & U241E Overhaul 2001-05 AUTOMATIC TRANSMISSIONS U240E & U241E Overhaul APPLICATION CAUTION: Flush oil cooler and oil cooler lines prior to transaxle installation. Oil cooling system contamination may cause premature transaxle

More information

TRANSMISSION AND TRANSFER CASE

TRANSMISSION AND TRANSFER CASE DR TRANSMISSION AND TRANSFER CASE 21-1 TRANSMISSION AND TRANSFER CASE TABLE OF CONTENTS page MANUAL TRANSMISSION- G56- SERVICE INFORMATION...1 MANUAL TRANSMISSION- GETRAG 238- SERVICEINFORMATION...69 MANUAL

More information

MTMANUAL TRANSMISSION GENERAL 1. SPECIFICATIONS. 1) General Specifications. 2) Tightening Torque MANUAL TRANSMISSION

MTMANUAL TRANSMISSION GENERAL 1. SPECIFICATIONS. 1) General Specifications. 2) Tightening Torque MANUAL TRANSMISSION 03-3 MT GENERAL 1. SPECIFICATIONS 1) General Specifications 2) Tightening Torque 03-4 OVERVIEW AND OPERATION PROCESS 1. OVERVIEW 4WD Features 1. All gears use the helical type and high strength materials.

More information

OVERHAUL. 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance.

OVERHAUL. 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance. 4168 OVERHAUL 410F701 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance. 0.10 to 0.40 mm (0.0039 to 0.0157 in.) 0.40 mm (0.0157 in.) C80538 2. INSPECT

More information

ALLDATA Online Mitsubishi Eclipse GS L4-2350cc 2.4L SOHC MFI - Input Shaft. Input Shaft

ALLDATA Online Mitsubishi Eclipse GS L4-2350cc 2.4L SOHC MFI - Input Shaft. Input Shaft Page 1 of 16 Home Account Contact ALLDATA Log Out Help BEST FORD BEST FORD00001 Select Vehicle New TSBs Technician's Reference Component Search: OK 2002 Mitsubishi Eclipse GS L4-2350cc 2.4L SOHC MFI Conversion

More information

Jr. T GENERAL. BAM: Bomber Aerospace Material. Special alloy extracted from aerospace material. Ø TRAVEL ±

Jr. T GENERAL. BAM: Bomber Aerospace Material. Special alloy extracted from aerospace material. Ø TRAVEL ± 175 15 GENERAL The double clamp fork is specifically designed for Downhill use. The fork is sprung by a mechanical spring and uses hydraulic rebound damping. Spring pre-load adjustment controlled via external

More information

DIFFERENTIALS & AXLE SHAFTS

DIFFERENTIALS & AXLE SHAFTS DIFFERENTIALS & AXLE SHAFTS 2001 Chevrolet Camaro 2000-01 DRIVE AXLES General Motors Differentials & Axle Shafts Chevrolet; Camaro Pontiac; Firebird DESCRIPTION & OPERATION Drive axle is a semi-floating,

More information

FRONT AXLE Click on the applicable bookmark to selected the required model year. Purchased from

FRONT AXLE Click on the applicable bookmark to selected the required model year. Purchased from FRONT AXLE Click on the applicable bookmark to selected the required model year. 26-1 FRONT AXLE CONTENTS GENERAL INFORMATION... 2 SERVICE SPECIFICATIONS... 4 LUBRICANTS... 4 SEALANTS... 5 SPECIAL TOOLS...

More information

HGM-E LSHT Wheel Motor Service and Repair Manual

HGM-E LSHT Wheel Motor Service and Repair Manual HGM-E LSHT Wheel Motor Service and Repair Manual BLN-52198 January 2018 Table Of Contents Foreword... 1 How to use this manual... 2 General Instructions... 2 General Description... 2 Tools... 3 Torques...

More information

Clutch, servicing. Special tools, testers and auxiliary items required. Flywheel retainer Thrust pad 3062

Clutch, servicing. Special tools, testers and auxiliary items required. Flywheel retainer Thrust pad 3062 Page 1 of 10 30-36 Clutch, servicing Special tools, testers and auxiliary items required Flywheel retainer 10-201 Thrust pad 3062 Page 2 of 10 30-37 Centering mandrel 3176 Grease G 000 100 Notes: Observe

More information

REMOVAL TF REMOVE TRANSFER INDICATOR SWITCH (a) Remove the switches and gaskets. HINT: Indicator switch:

REMOVAL TF REMOVE TRANSFER INDICATOR SWITCH (a) Remove the switches and gaskets. HINT: Indicator switch: 20 NO. 1 NO. 2 F043499 REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag

More information

REAR AXLE Click on the applicable bookmark to selected the required model year

REAR AXLE Click on the applicable bookmark to selected the required model year REAR AXLE 27-2 REAR AXLE General Information GENERAL INFORMATION 27100010118 The rear axle is a banjo-type semi-floating type. The axle shaft bearings are: *Single taper bearings for vehicles without

More information

TRANSMISSION AND TRANSFER CASE

TRANSMISSION AND TRANSFER CASE XJ TRANSMISSION AND TRANSFER CASE 21-1 TRANSMISSION AND TRANSFER CASE TABLE OF CONTENTS page AX5 MANUAL TRANSMISSION... 1 NV3550 MANUAL TRANSMISSION... 42 AUTOMATIC TRANSMISSION 30RH... 88 page AW 4 AUTOMATIC

More information