SYSTEM CLOCKS Catalogue

Transcription

1 SYSTEM CLOCKS Catalogue

2 QCG- GP S -

3 MASTER CLOCK (QUARTZ) WALL-MOUNT TYPE SEIKO QC-55 Series is a high-precision quartz master clock. By connecting with an external master clock generating 3-sec polarized signal output, time correction can be made. Models operating on AC 11V (QC-55X1) and AC V (QC-55X) are available. (1) Master clock function (QC-551X, QC-55X and QC-553X) Up to 3 secondary clocks can be connected to each channel (if the current consumption of each secondary clock is 1mA). () External synchronization function By connecting with an external master clock generating 3-sec polarized signal output, the loss/gain of the clock is corrected automatically QC-55 Series QC-5511/ 551 QC-551/ 55 QC-5531/ 553 QC-5531 / Rack-mount type is available QC-5531 / 553 CONTENTS Model No. FUNCTIONS Number of secondary clock circuits Crystal oscillator frequency Time accuracy Time Master clock display Monitor clock Time Master clock setting Monitor clock Daylight saving time MASTER CLOCK Secondary clock driver External synchronization Synchronization output Power supply Power consumption Power failure backup Driving signal Max. number of secondary clocks to drive Maximum driving capacity Backup power Battery protection Signal voltage detection Master clock Secondary clock driver Operational temperature range and humidity range Dimensions Material Weight Accessories Options QC-5511 QC circuit SPECIFICATIONS QC-551 QC-55 QC-5531 QC circuit circuit MHz Weekly rate of less than.7 seconds ( 5 35 ) ; no accumulated error after time correction Year, month, date hour, minute, and seconds; and Digital display in 4-hour indication (not displayed during power failure) 3-second interval hand movement Setting of year, month, date, hour, minute and seconds 6X speed quick advance of hands by APC system Setting of year, month, date and hour for start date, and month, date and hour for end date DC 4V 3-sec. polarized signal ; Pulse width of.5-sec. ; No-contact 3 units 6 units 9 units 1mA / unit ; 3 units / circuit 36mA 7mA 1,8mA 36mA / circuit DC 4V ; Built-in sealed Ni-Cd rechargeable battery Overdischarge prevention circuit Signal voltage stopper function (stops output when secondary clock driving voltage lowers) DC 4V 3-sec. polarized signal; Every hour except 7, 19,, and 1 o clock; Synchronizable loss/gain range Less than 15 seconds RS-4 QC-55X1 : AC 11V 1% or DC 4V 1% QC-55X : AC V 1% or DC 4V 1% 1W 3W 4W Approx. 5 years (no indication on digital display, counting by internal clock only) 3 hours (in case of power failure of more than 3 hours, hands are adjusted automatically after recovery.) 1 5 / 8% with no dew condensation W4 H354 D11mm Front panel : ABS and stainless steel, pearl gray with a slight gloss Rear panel: Stainless steel, pearl gray with a slight gloss Approx. 7.kg Approx. 7.kg Approx. 7.5kg Plastic foot, 4 pcs; Miniature fuse; Instruction manual; Mounting hole drilling template; and Insulated crimp terminal Rack-mounting fittings (in accordance with EIA Standard) How to Drive Secondary Clocks Accuracy and Synchronization of Secondary Clocks The role of the secondary clock in a time-keeping system is to accurately reproduce the time signal supplied by the master clock. The master clock and secondary clocks are connected electrically, and the Crystal oscillator frequency of 3.768kHz or MHz/sec. from the master clock is reduced in several stages by the frequency diving LSI and finally transmitted to the secondary clock as a 1-sec. or a 3-sec. polarized signal of 4V DC. The secondary clock converts this electrical signal into mechanical energy and, with the same precision as the master clock, simultaneously displays the correct time. 4V 1sec. or 3sec. Positive position 1sec. or 3sec. Negative position 1sec. or 3sec. 4V t t Neutral position t

4 INDOOR SECONDARY CLOCK(4V) WALL TYPE / RECESSED TYPE Current consumption of a wall type and a recessed type secondary clock is 1mA. Input signal of a wall type and a recessed type secondary clock is 3-sec. polarized signal / DC 4V. ( F-1 is 1-sec. polarized signal / DC 4V.) 6-mm Diameter Round Type SC-C Frame Steel, Cream Thickness 4mm Weight 1.kg SC-1 Dial Aluminum, Silver Frame Steel, Semi-mat black Thickness 4mm Weigh 1.kg 3-mm Diameter Round Type SC-34 Dial Brass, White hairline finish Hour marker Brass, Black Outer Frame Polished chromium finish Thickness 46mm Weight.kg 31-mm Diameter Round Type SC-3 SC-3C (cream color) is also available. Frame Steel, Gray Thickness 4mm SC mm Diameter Round Type Square Type with Standard Frame Dial Aluminum, Silver Frame Steel, Semi-mat, Black Thickness 4mm SC-4 SC-4C (cream color) is also available. Frame Steel, Gray Thickness 55mm Weight.5kg SC-31C SC-31 (gray color) is also available. Frame Steel, Cream Thickness 4mm SC-36 Frame Steel, Cream Thickness 4mm SC-419 Frame Steel, White Thickness 55mm Weight.5kg SC-3 Frame Steel cream Thickness 4mm SC-316 SC-316C (cream color) is also available. Frame Steel, White Thickness 4mm 31-mm Diameter Round Type with second hand (1-sec. polarized signal) F-1 Frame Steel, White Thickness 4mm F-1 is driven entirely by Master Clock QCG-1. SC-3 SC-3C (cream color) is also available. Dimensions W31 H31 D45mm Frame Steel, Gray Weight.kg SC-33K Dimensions W31 H31 D75mm Dial Cloth covered, Black Hour marker Blass, White hair-line finish Hands Blass, White hair-line finish Frame Steel, Cream Speaker Max. input 4W With output transformer Input impedance : 7k Output impedance : 8k Weight.kg SC-34 Dimensions W31 H31 D45mm Dial Aluminum, Silver Frame Steel, Semi-mat black Weight.kg Recessed Type SC-4C Dimensions W4 H31 D55mm Frame Steel, Cream Weight.5kg SC-4K Dimensions W4 H31 D75mm Frame Steel, Cream Speaker section Cloth covered, Black Speaker Max. input 4W With output transformer Input impedance : 7k Output impedance : 8k Weight 3.kg Square Type with Wood Finish SC-3S SC-41 Dial Wood, Walnut finish Hour marker Brass, Silver metallic painted Hands Brass, Silver metallic painted SC-3S : W3 H1 D45mm (1.kg) SC-41 : W4 H95 D45mm (1.5kg) Sharp, straight-bar type hour marker SC-34S SC-44S Movement cover Hour marker Hands SC-34S : 3mm diameter (.5kg) SC-44S : 4mm diameter (.6kg) Straight-bar type, with numerals for the quarter-hours SC-341S Movement cover Hour marker Hands SC-341S : 3mm diameter (.5kg) Circular type hour marker SC-34 SC-441 Movement cover Hour marker Hands SC-34 : 3mm diameter (.5kg) SC-441 : 4mm diameter (1.kg) 3

5 DOUBLE-FACED TYPE Current consumption of a double-faced secondary clock is 4mA. Input signal of a double-faced secondary clock is 3-sec. polarized signal/dc 4V. Double-faced Suspended Type SC-36 Dimensions 31mm Dia D15mm Frame Steel, Gray Pipe 34mm Dia D36mm Weight 8.kg SC-46 Dimensions W4 H31 D18mm Frame Steel, Gray Flange W5 H5 D1mm Weight 8.kg Double-faced Bracket Type SC-461 Dimensions W4 H31 D18mm Frame Steel, Gray Flange W5 H5 D1mm Weight 8.kg Double-faced Suspended Type (Condensed Resin Illumination) Yellow(Y) Green(G) Light orange (L) Orange (O) RWS-6WHB (Y L G O) RWS-5WHB (Y L G O) RWS-4WHB (Y L G O) Fluorescent ramps and power are unnecessary for illumination. Easy to maintenance. To be suitable for station use. Dimensions 6WHB : W65 H58 D5mm 5WHB : W51 H45 D178mm 4WHB : W4 H36 D173mm Dial Condensed resin illumination Hands Yellow (Y), Light orange (L) :Aluminum, Mat-black Green (G), Orange (O) : Condensed resin Frame Steel, Gray-brown painted Weight 6WHB : Approx. kg (excluding a suspended pipe) 5WHB : Approx. 16kg (excluding a suspended pipe) 4WHB : Approx. 1kg (excluding a suspended pipe) Incident rays The mechanism of Condensed resin illumination Condensed resin illumination Back plate Letter indication fluorescent dye INFORMATION System configuration Distance (m) Master Clock to Secondary Clocks 1-sec. polarized signal Number of Secondary Clocks / Circuits , 1. (mm) 1.6 (mm). (mm).6 (mm) 3. (mm) QCG-1 6 AC DC4V 3-sec. polarized signal AC UP to 11 analog secondary clocks (if the current consumption of each secondary clock is 1mA.) RS-4 serial output UP to 1 digital secondary clocks In case of QC-55 Series, up to 3 secondary clocks can be connected to each channel (if the current consumption of each secondary clock is 1mA). AC AC Option Equipment for Secondary Clocks APX-111/11 Clock controller Cristal oscillator frequency MHz Time accuracy Weekly rate of less than.7 second ( 5 35 ) Input power supply APX-111 : AC1-1V APX-11 : AC-4V Power consumption W (MAX) Output signal DC 4V 3-sec. polarized signal circuits Power failure backup 3 hours Dimensions W18.5 H17 D79 mm Weight Approx. 76g MT-1 Secondary clock monitor for APX-111/11 Dimensions W9 H9 D67mm Weight Approx. 5g APX-111/11 MT-1 FA-11 Secondary clock repeater FA-11 amplifies the 3-sec. polarized signal transmitted by the master clock. Input signal DC 4V 3-sec. polarized signal / AC1-4V Output signal DC 4V 3-sec. polarized signal Number of secondary clock to drive 3 units Power failure backup 3 hours Dimensions W H31 D96mm Material Steel with pearl-gray painted Weight Approx. 3.7kg FA-3 Hand Adjuster with jack plug Among secondary clocks driven by a master clock, the FA-3 is used for adjusting the hands of a large-sized secondary clock mounted on a wall in a very high position. By the signal from the FA-3, the clock is adjusted apart form a signal from a master clock. Built-in battery 6P (9V 3 7V) Operating time Approx.1 minutes (, load) Hand moving speed Approx. 3 times Output terminal Jack plug type Dimensions W83 H14 D56mm Material Steel, Gray Weight Approx. 65g FA-31 Jack-plug plate for single-faced clocks FA-11 FA-3 Jack-plug plate for double-faced clocks FA-3 FA-31 FA-3 4

6 4 Et udeop. 1, No. 3 Yuyakekoyake Goi nghome

7 DIGITAL CLOCK INDEPENDENT CLOCK For indoor / outdoor rain proof Type Model No. CONTENTS SPECIFICATIONS RBC-N (Wall type) RBC-3N, 33N (Dobule-faced type) Digit height mm (Orange) mm (Yellow) RBC-N Wall type Dimensions Weight W95 H38 D184mm 3kg W95 H38 D3mm 65kg RBC-3N Suspended type (Double-faced) Accuracy Operational temperature range Input power Current consumption Internal illumination Display Power failure backup Within. sec./day at normal temperature 6 AC (5/6Hz) Time synchronization with the master clock is possible. Approx. 1.6A (Including.7A for internal illumination) FL-3W 1 (With automatic flasher) Magnetic inversion system Changeover between 1-and 4-hour indications Approx. 1hours Approx. 1.9A (Including.7A for internal illumination) RBC-33N Bracket type (Double-faced) Steel, Metallic brown Case Front : Transparent glass (Thickness : 3mm) Please turn off the illuminating light while the clock is shone directly by the sun in the daytime. For Indoor Type Model No. CONTENTS SPECIFICATIONS SLC-1W (Wall type) SLC-1W (Double-faced type) SLC-1E (Wall type) SLC-1E (Double-faced type) SLC-1W Wall type Digit height Wall type 1mm (White) W6 H17 D6mm 1mm (Orange) W67 H D6mm Dimensions Double-faced W66 H176 D17mm W676 H D17mm SLC-1E Wall type Weight Wall type Double-faced 3.5kg 1.5kg 3.8kg 13.5kg Accuracy Within. sec./day at normal temperature Operational temperature range 1 5 SLC-1W Suspended type (Double-faced) Input power Current consumption Wall type Double-faced AC (5/6Hz) Time Synchronization with the master clock is possible. Approx..1A Approx..A Approx..A Approx..4A Display White / Orange LED Changeover between 1-and 4-hour indications Case Plastic, Yellowish white SLC-1E Suspended type (Double-faced) A hand adjuster is optional. 6

8 WEEKLY DIGITAL CLOCK Mounting Structure WDC-4 Display LED (White) Digital height Time : 4mm, Day : 1mm Dimensions W6 H15 D64mm Weight Approx. 1.3kg In addition to its single usage, this weekly digital clock is uniquely designed in such a way that it can form an original world time clock by applying multiple units. No need for a master clock since it is a twin synchronous system. (A power box is required when multiple clocks are used to form a world time clock.) The installation can be either wall type or recessed type. And a map panel of your design can be prepared on request. 96 Configuration of Weekly Digital Clock (Simple substance) Configuration of Weekly Digital Clock (Plurality) Local Voltage DC4V 3-sec. polarized signal Wiring AC 1V 4V (AC1V~4V) Time synchronization with master clock WDC-4 No.N WDC-4 No.3 WDC-4 No.1 Earth WDC-4 WDC-4 Earth No.4 No. MORNING ALARM CLOCK GT-943AD GT-94RC GT-943 GT-943 To be suitable for hotel use Easy to make time settings by using the remote controller GT-94RC (optional). Alarm signal output is available. GT-943 is equipped with automatic light regulating sensor. GT-94RC Remote controler (Optional) Outer Dimensions W66 H111 D8mm Weight Approx. 1g (excluding dry cell batteries) Time accuracy Monthly rate of less than 15 second ( 5 35 ) Input power supply DC 1V 1% AC adopter shall be required. For AC1V (GT-94AD) is available as an optional. Power failure backup 4 hours Time display Digital type liquid crystal Changeover between 1-and 4-hour indications by Remote controller GT-94RC (optional). Time setting By special operation with push buttons (up and down switches) or Remote controller GT-94RC (optional) Alarm setting By push buttons (up and down switches) Alarm Sound Electronic sound (-step driving tone) Light Automatic light regulating sensor Type Panel embedded type Dimensions W1 H7 D6.5mm Weight Approx. 13g 7

9 OUTDOOR CLOCK LARGE-SIZED WALL CLOCK (OUTDOOR/RAINPROOF) Dial of a large-sized clock is made of steel except for internal illumination type which is made of acrylic resin. Input signal of a wall type secondary clock is 3-sec. polarized signal/dc 3.6V. Cost for installation work is not included. Power consumption of 55 and 7mm types is 18mA, and that of 9 and 1,mm types is 6mA. 55-mm Diameter 9-mm Diameter FC-53 Frame Steel, Coffee brown color Thickness 9mm Weight 4.7kg FC-93 Frame Steel, Coffee brown color Thickness 15mm Weight 1kg 7-mm Diameter 1-mm Diameter FC-73 Thickness 99mm Weight 7.5kg Internal FC-7131 illumination type Thickness 17mm Weight 11.5kg All the other specs.are the same as those of FC-73. FC-13 Frame Steel, Coffee brown color Thickness 15mm Weight 5kg FC-77 Frame Stainless steel polished Thickness 99mm Weight 7.kg FC-7171 Internal illumination type Thickness 17mm Weight 1.7kg All the other specs.are the same as those of FC-77. FC-18 Frame Stainless steel polished Thickness 15mm Weight 5kg FC-7191 Internal illumination type Thickness 17mm Weight 11.5kg Protector for 7-mm outdoor wall clock TK-S Frame Stainless steel, Coffee brown color Photo example : TK-S furnished on FC-73 Controller AP-431 When installing a secondary clock, a controller for exclusive use with it is required (optional). Controller Case QF-BOX Visibility Distance 6mm 31mm 4mm 55mm 63mm 7mm 9mm 1,mm Configuration of Large-Sized Wall Clock Wiring Clock AC power 7 14m 1 m 4m 8 56m 4 8m 56 11m 8 16m 11 4m Controller 8

10 LARGE-SIZED DOUBLE-FACED POLE CLOCK (RAINPROOF) Cost for pole and installation work are not included. Input signal of a pole clock is 3-sec. polarlized signal / DC3.6V. Power consumption of a pole clock is 18mA. 7-mm Diameter Grounding Work (mm) 3 FC-7831 Internal illumination type Thickness 3mm Weight kg FC-7851 Internal illumination type Thickness 3mm Weight kg Overall Length of Pole 5, Clock Unit Pole Clock Controller 4,36 7 G.L. 95 Concrete Rubble Glass 3 Grounding GND 1 (Pole and base are shown here for reference purpose only.) Controller Controller Case FC-7871 Internal illumination type FC-7891 Internal illumination type Frame Stainless steel Thickness 3mm Weight 18.5kg Thickness 3mm Weight kg AP-431 When installing a secondary clock, a controller for exclusive use with it is required (optional). QF-BOX LARGE-SIZED SUSPENDED TYPE CLOCK (OUTDOOR / RAINPROOF) 7-mm Diameter Digital Regulation Gain or loss of the clock controller can be detected and corrected automatically by every zero-setting operation if conducted at regular intervals. This function is called the digital regulation. FC-7631 Double-faced type with internal illumination Error Without digital regulation With digital regulation Frame Steel, Coffee brown color Thickness 3mm Weight 1kg Input voltage DC 3.6V Current 18mA consumption Zerosetting Zerosetting Zerosetting Zerosetting Remarks: Time In case that an output voltage from a master clock is DC 4V (except QC-55 Series), you need a resistor adaptor R-7 or R-9 (optional) which has to be connected between the FC-series and the master clock. 9

11 SOLAR-POWERED CLOCK Wall Type : Cost for installation work is not included. Double-faced Pole Type : Cost for pole and installation work are not included. Wall Type SL-1 (Solar Cell Panel) is included. Configuration of Wall Type Solor Clock Solar Cell Panel Clock Wiring QF-53 Thickness 9mm Weight 4.7kg QF-73 Thickness 99mm Weight 7.5kg QF-77 Frame Stainless steel Thickness 99mm Weight 7kg Solar Clock Controller Double-faced Pole Type SL-1 (Solar Cell Panel) is included. Controller Controller Case QP-41 When installing a secondary clock, a controller for exclusive use with it is required (optional). QF-BOX Grounding Work (mm) 3 Solar Cell Panel QF-787 Frame Stainless steel Thickness 3mm Weight 18kg QF-783 Thickness 3mm Weight 19.5kg 89.1 Clock Unit 7 Overall Length of Pole 5, Pole 4,36 Clock Controller G.L. 95 Concrete QF-785 Thickness 3mm Weight 19.5kg QF-789 Thickness 3mm Weight 19.5kg Glass 3 Grounding GND 1 (Pole and base are shown here for reference purpose only.) Rubble 1

12 -4-3, Fukuzumi, Koto-ku, Tokyo , Japan Phone / Fax mark means that the product does not contain lead, cadmium, mercury, hexavalent chromium, polybrominated biphenyl (PBB) and polybrominated diphenyl ether (PBDE) flame retardants referring to the RoHS Directive (/95/EC). 1.9 TO