Owner s manual for installation, usage and maintenance

Transcription

1 Owner s manual for installation, usage and maintenance

2 AQC Dust Collecting Systems This manual is property of the owner. Leave with the unit when set-up and start-up are complete. AQC Dust Collecting Systems inc. reserves the right to change design and specifications without prior notice. 2

3 Introduction This present manual refers to the Maxiroll and Maxicart portable filtration units. It includes important information concerning the installation, usage and maintenance of your units. Read this manual thoroughly and apply the directives and procedures. Staff and personnel using the system will have to trained on safety measures and maintenance instructions. Warning! The dust or pollutant to be filtered may not be suitable for the Maxiroll or Maxicart. Ensure the unit selected is adequate for your application. Contact A.Q.C. Inc. if you have any doubt in regard to the usage of your extension swing boom. Warning: not following directives and procedures could cause injuries or property damages. Information on the Maxiroll and Maxicart portable filtration units Model : Serial number : Date of Delivery date : installation : Name of customer : Address : Type of filters : Accessories : Other : 3

4 AQC Dust Collecting Systems Index Introduction...3 Index...4 Presentation...5 Maxiroll...5 Maxicart...6 Normal usage...7 Components...8 Maxiroll...8 Maxicart...9 Technical specifications...10 Maxiroll...10 Maxicart...11 Installation...12 Inspection of goods...12 Fume arm installation (if ordered with)...12 Electrical connection...13 Performance...14 Check list...14 Performance instructions (Pulse cleaning system)...14 Instruction de fonctionnement...14 Compressed air cleaning...14 Replacement/cleaning of Maxiroll aluminum spark trap filter...15 Replacement/cleaning of Maxicart aluminum spark trap filter...15 Replacement of Maxiroll/Maxicart filter cartridge...16 Maxiroll...16 Maxicart...17 Replacement of Maxiroll charcoal filter...18 Replacement of Maxicart charcoal filter...18 Replacement of Maxiroll HEPA filter...19 Replacement of Maxicart HEPA filter...19 Maintenance and inspections...21 Troubleshooting...22 Service notes...23 Limited warranty

5 Maxiroll presentation The Maxiroll portable filtration unit is a single cartridge dust collector designed to capture and filter welding smoke and fine volatile dust coming from sanding or buffing processes. The upflow dust collector offers high efficiency while requiring low energy consumption. The cartridge is cleaned by using compressed air contained in the reserve air tank. The Maxiroll collector is widely used in areas where dust and airborne pollutants are a nuisance. Main applications are welding, buffing, sanding, grinding processes as well as pharmaceutical and food grade applications. The Maxiroll units stores dust in the two (2) drawers at the bottom of the unit. Each Maxiroll unit includes: Painted steel cabinet 1 HP direct drive fan/motor, 115/1/60 (other voltages are available) Side access door Two (2) dust collector drawers Spark arrestor aluminum filter Spun bond polyester cartridge Charcoal filter (polyester fabric) Sound insulating foam 15 (4,6m) electrical cord with three (3) prong plug ON/OFF switch Two (2) 5 casters (non-swivel) and two (2) 3 casters (swivel) with foot brakes Cabinet grab handle Push button for air pulse and cartridge cleaning Reserve air tank 1/4 NPT for compressed air line Maxiroll units may also have the following optional equipment : LED light in Maxair fume arm hood HEPA filter Activated charcoal filter (granular) Automatic pulse cartridge cleaning The Maxiroll unit is shipped fully assembled except for the installation of the Maxair fume arm if ordered with the unit. 5

6 AQC Dust Collecting Systems Maxicart presentation The Maxicart portable filtration unit is a double cartridge dust collector designed to capture and filter welding smoke and fine volatile dust coming from sanding or buffing processes. The upflow dust collector offers high efficiency while requiring low energy consumption. The cartridge is cleaned by using compressed air contained in the reserve air tank. The Maxicart collector is widely used in areas where dust and airborne pollutants are a nuisance. Main applications are welding, buffing, sanding, grinding processes as well as pharmaceutical and food grade applications. The Maxicart units stores dust in the drawer at the bottom of the unit. Each Maxicart unit includes: Painted steel cabinet 3 HP direct drive fan/motor, voltage as per customer s request Side access door Dust collector drawer Spark arrestor aluminum filter Two (2) cartridges (polyester or cellulose) Charcoal filter (polyester fabric) Sound insulating foam 15 (4,6m) electrical cord (no plug) ON/OFF switch Two (2) 5 casters (non-swivel) and two (2) 3 casters (swivel) with foot brakes Cabinet grab handle Push button for air pulse and cartridge cleaning Reserve air tank 1/4 NPT for compressed air line Maxicart units may also have the following optional equipment : LED light in Maxair fume arm hood HEPA filter Activated charcoal filter (granular) Automatic pulse cartridge cleaning The Maxicart unit is shipped fully assembled except for the installation of the Maxair fume arm(s) if ordered with the unit. 6

7 Normal usage for Maxiroll/ Maxicart The Maxiroll and Maxicart units are designed to remove dust from the worker s breathing zone resulting from a fabrication process. Each portable dust collector is built to follow existing requirements concerning interior air quality in industrial facilities. The unit should not serve any other application without the approval of A.Q.C. Inc. Warning! Flammable or explosive dusts and solvents present a fire or explosion hazard within the collector. Under no circumstances, those pollutants should be filtered by the collector unless it has been designed to that effect and equipped with an explosion relief venting system or fire extinguishing device. This is the reason why special attention is required with the handling or usage of dust collecting equipment in contact with flammable or explosive dusts and solvents. Any burning or flammable material such as a spark created by metal grinding, lit cigarettes, spark, etc. should not be introduced within the collector where it could cause a fire or explosion. Warning! THIS UNIT SHOUD NOT BE USED FOR METAL CUTTING OR GOUGING. Such operations create a lot of sparks. Not following this warning could start a fire in the unit. NOTE : these units are not be used outside. 7

8 AQC Dust Collecting Systems Maxiroll components 1. Welded steel cabinet with powder coat paint 2. Access door to internal components with Duro-Dyne type handles for air tight seal. 3. Aluminum pre-filter for sparks and larger particles. 4. Main cartridge for finer dusts and smoke 5. Polyester charcoal filter to reduce odors 6. Cabinet grab handle 7. Push button for pulse cleaning 8. Compressed air connection (1/4 NPT) 9. Compressed air tank 10. Pneumatic valve 11. Venturi 12. Swivel casters with foot brakes 13. Rear casters (fixed) 14. Dust drawer equiped with a rack and mounted on rails. Locking mechanism for proper cartridge adjustment 15. Aluminum impeller, spark proof, backward inclined design. 16. Motor 17. Foam sound insulation Each unit is equipped with a starter and overload protection A

9 Maxicart components 1. Welded steel cabinet with polyurethane paint 2. Access door to internal components with Duro-Dyne type handles for air tight seal. 3. Aluminum pre-filter for sparks and larger particles. 4. Two(2) main cartridges for finer dusts and smoke 5. Polyester charcoal filter to reduce odors 6. Cabinet grab handle 7. Push button for pulse cleaning 8. Compressed air connection (1/4 NPT) 9. Compressed air tank 10. Pneumatic valve 11. Venturi 12. Swivel casters with foot brakes 13. Rear casters (fixed) 14. Dust drawer equiped with a rack and mounted on rails. Locking mechanism for proper cartridge adjustment 15. Aluminum impeller, spark proof, backward inclined design. 16. Motor 17. Foam sound insulation Each unit is equipped with a starter and overload protection A

10 AQC Dust Collecting Systems Maxiroll technical specifications Unit Filters Weight without arm lb / kg 240 / 110 Weight with arm lb / kg 292 / 132 Motor TEFC Frame 56 / C face Prefilter included (aluminium) Quantity 1 Dimensions in / mm 17 x 21 x 1 / 540 x 440 x 25 Power supply V / Hz As requested or specified Power HP / kw 1 / 0.75 Filtering efficiency Maintenance microns Washable / replaceable R.P.M Pressured air tank 3 gallon capacity Air pression required 80 to 100 P.S.I Pressured air connection 1/4 N.P.T. Airflow with arm CFM / L/s 650 / 305 Airflow without arm CFM / L/s 850 / 400 Noise level db(a) 3 (1m) Tray # gallon Dust storage capacity Tray # 2 2 gallons Main cartridge included (polyester, 130 sq. ft.) Quantity 1 Dimensions in / mm 12.8 x 26 / 325 x 660 Filtering efficiency micron Maintenance Cleaned by air pulse / replaceable / washable Final charcoal filter included (polyester fabric) Quantity 1 Dimensions in / mm 17 x 21 x 1 / 540 x 440 x 25 Filtering efficiency 30 % molecular Maintenance Disposable / replaceable Method Air pulse Valve Pulse cleaning operation Push button standard (automatic optional) Through venturi / reverse pulse Diaphragm HEPA after-filter with rack (optional) Quantity 1 Dimensions in / mm 16 x 20 x 6 / 400 x 500 x 150 Filtering efficiency % Constant air connection Not required Maintenance Disposable / replaceable Tank fill time Air pulse duration Air tank capacity Required air pressure Compressed air requirement 4 to 6 seconds 200 ms 3 gallon 80/90 P.S.I Dry and clean CGM granular activated charcoal final filter (optional) Quantity 1 Dimensions in / mm 17 x 21 x 1 / 540 x 440 x 25 Filtering efficiency % molecular Maintenance Disposable / replaceable Amperage draw Amperage draw amps amps amps amps amps 10

11 Maxicart technical specifications Unit Filters Weight without arm lb / kg 345 / 156 Weight with(1) arm (2) arm lb / kg 405 / / 212 Motor TEFC Frame 56 /C face Prefilter included (aluminium) Quantity 1 Dimensions in / mm 17 x 21 x 1 / 540 x 440 x 25 Power supply V / Hz As requested or specified Filtering efficiency 10 microns Power HP/KW 3 / 2.2 R.P.M Pressured air tank 3 gallon capacity Air pressure required 80 to 100 P.S.I Pressured air connection 1/4 N.P.T. Airflow with (1) arm (2) arms CFM/L/s 1200 / / 640 Airflow without arms CFM/L/s 1500 / 710 Noise level db(a) 3 (1 m) Dust storage capacity Tray # 1 2 gallon Maintenance Washable / replaceable Main cartridge included (polyester, total of 260 sq. ft.) Quantity 2 Dimensions in/mm 12.8 x 26 / 325 x 660 Filtering efficiency micron Maintenance Cleaned by air pulse / replaceable Final filter included (polyester fabric) Quantity 1 Dimensions in/mm 21 x 26 x 1 / 533 x 660 x 25 Filtering efficiency 30 % molecular Pulse cleaning operation Maintenance HEPA after-filter with rack (optional) Disposable / replaceable Method Air pulse Valve Push button standard (automatic optional) Through venturi / reverse pulse Diaphragm Quantity 1 Dimensions in / mm 20 x 28 x 6 / 500 x 700 x 150 Filtering efficiency % Constant air connection Not required Maintenance Disposable / replaceable Tank fill time Air pulse duration Air tank capacity Required air pressure Compressed air requirement 4 to 6 seconds 200 ms 3 gallon 80/90 P.S.I Dry and clean CGM granular activated charcoal final filter (optional) Quantity 1 Dimensions in/mm 20 x 28 x 1 / 500 x 700 x 25 Filtering efficiency % molecular Maintenance Disposable / replaceable Amperage draw Amperage draw 208/230/1/60 17 amps 460/3/ amps 208/230/3/ amps 575/3/ amps 11

12 AQC Dust Collecting Systems Installation Warning! Only qualified personnel should install and/or use the unit. Tooth Inspection of goods Locking screw The Maxiroll and Maxicart units are shipped fully assembled with the exception of the Maxair fume arm if ordered with the unit. Proceed with a visual inspection upon receiving the material for any damages or missing components. Open the lateral access door to ensure all internal components are still in place. Fume arm installation (if ordered with unit) Necessary tools The following list of tools are recommended to install and adjust the Maxair fume arm. Ratchet set Spanners and/or wrenches 3/16 hex key 7/8 socket Warning: keep the plastic wrap on the fume arm until completely installed to avoid damages during installation. Arm installation steps NOTE ON MAXAIR FUME ARM INSTALLATION : the Maxair fume arm does not make a full 360 degrees rotation. If you need to have the fume arm do a full rotation, remove the hex bolt from the top part of the arm socket. A maximum 4 or 5 full rotations (left or right) will then be possible before reversing the rotations. (See drawing # 2 : socket) Figure 2 : Socket 1. Apply the front casters swivel foot brakes on the unit. 2. Open the Maxair fume arm carboard box and take out the fume arm. Proceed with a visual inspection to ensure all components are in place. 3. Lift the arm up and position over the round outlet. When doing so, make sure you do not slide the fume arm socket on the paint surface of the unit to avoid scratches and/or dents to the cabinet. 4. Align the Maxair fume arm socket holes with the ones around the opening. Ensure the locking screw faces outward (front of the unit) and tooth faces the rounded part of the cabinet. Once the holes are perfectly aligned, bolt arm socket to cabinet. 12

13 Figure 1: Maxiroll arm installation ratchet to the desired tension. DO NOT OVERTIGHTEN THE JOINTS. Once all joints are adjusted, the arm should move freely in all directions without sagging or being too stiff to maneuver into position.for more information on the usage of the Maxair fume arm, refer to owner s manual supplied with the arm. Electrical connection on Maxiroll / Maxicart Figure 1b: Maxicart arm installation Note on Maxiroll electrical: standard unit is supplied with a 115V starter, 15 power cord and 3 prong plug. If other voltage is ordered, plug will be supplied by customer. Note on Maxicart electrical: unit is supplied as per required voltage and 15 power cord. Plug will be supply by customer. 1. Plug the unit into a proper electrical outlet. 2. If you need to use an electrical extension cord, ensure the cord meets the requirements for the motor amperage. Note: the Maxicart unit can be equipped with two (2) 6 Maxair fume arms or one (1) 8. Remove appropriate diameter cover plates to install fume arms for installation. 3. Ensure you do not move the unit further than the length of the cord. This could result in breaking or ripping the cord and cause an electrical shock. 5. Ensure the fume arm pivots smoothly without grinding noise or wobbling movement. 6. The Maxair fume arm joints are pre-adjusted at the factory but will require final adjustment upon installation. Using an adjustable wrench to hold the head of the bolt, tighten or loosen (as needed) the 7/8 nut with a 13

14 AQC Dust Collecting Systems Performance Check list Before starting the unit for the first time, the check list listed below must be followed to ensure all components work properly. 1. Remove all objects around the fume arm hood. 2. Ensure access door is closed and locked. 3. Ensure power cord is connected into an appropriate electrical outlet. 4. Start the unit and shut it off immediately. Listen for unusual noises coming from the motor or impeller. 5. Start the unit again and let it run for a few minutes before using it as per it s required application. Performance instructions (pulse cleaning system) 1. Plug the unit into a proper 120 VAC outlet. Turn the selector knob to the ON position. (See drawing # 3) 2. Positon the fume arm hood about 10 to 15 (250 à 380 mm) away from the welding gun or source of dust. Compressed air cleaning Note : a check valve should be tapped onto the 1/4 NPT connection before filling the compressed air tank. Air should be clean and dry. Warning! Do not operate the pulse cleaning system when filter access door is opened. To use the pulse cleaning system, follow the steps listed below in order to ensure the unit will perform adequately. 1. Connect the compressed air line to the unit with a 1/4 NPT connection. Tank should take about 4 to 6 seconds to fill. 2. For a longer use of the cartridge, it is best to feed 60 PSI into the air tank. Max PSI is Press the the red palm button to release the compressed air from the tank and to clean the cartridge. (Figure 3a et 3b) Figure 3a Maxiroll Red button Figure 3b Maxicart Red button 14

15 Replacement/cleaning of Maxiroll / Maxicart filters 2. Slide the filter (3) out of the cabinet. Warning! Wear appropriate safety gear such as safety goggles or gloves when replacing the cartridge. The filter cartridge may be heavier than expected. Do not shake or drop the cartridge. Use necessary precaution when replacing the filters to avoid injuries. 4. Frequency of pulse cleaning will depend on how often the unit is used or the type of dust to be filtered. Decrease in suction is a sign to pulse clean the cartridge. Replacement/cleaning of Maxiroll aluminum spark trap filter Follow these next steps to clean or replace the aluminum spark trap filter. NOTE : the spark trap filter is an important component of the Maxiroll unit. Avoid having this component may result in a fire in the filter cartridge. 3. Wash or brush away dirt in the filter. Ensure you do not damage the mesh fabric. 4. Proceed with a visual inspection for tears or rips. Replace if necessary. Put filter back in place. Replacement/cleaning of Maxicart aluminum spark trap filter Follow these next steps to clean or replace the aluminum spark trap filter. NOTE : the spark trap filter is an important component of the Maxicart unit. Avoid having this component may result in a fire in the filter cartridge. 1. Open access door (1) on the side of the cabinet using the handles (2). 1. Open the cabinet lateral side access door using the handles (2). 15

16 AQC Dust Collecting Systems 2. Slide filter out of cabinet (5). Maxiroll 1. Push the dust drawer lever down (5). 3. Brush clean or wash aluminum filter. Ensure you do not damage the screen 2. Slide the dust drawer out of the unit (6). Lift cartridge off the drawer (7). 4. Proceed with a visual inspection of the filter. Replace if necessary. Insert filter b back in unit. Replacement of Maxiroll / Maxicart filter cartridge The life expectancy of the cartridge is only limited by the type of dust to be filtered and number of hours used. However, it is recomended to replace the cartridge after hours of usage. If a cartridge tears or rips open, the cartridge should be replaced as soon as possible. 3. Dispose of cartridge in a safe manner and according to environmental regulations. 4. Empty the dust drawer (9) by pulling out the grill (8) Before replacing the cartridge, shut the unit OFF and remove the plug from the electrical outlet. Follow these next steps to replace the cartridge. 16

17 5. Push the dust drawer and the grill back into the unit before installing a new cartridge. 6. Install a new cartridge and push the dust drawer level up. NOTE : for better and safe performance, use same cartridge material and properties. 3. Dispose of cartridges in a safe manner and according to environmental regulations. 4. Install a new cartridges. Ensure new cartridges are sitting firmly on the drawer cartridges holder. Maxicart 1. Push the two (2) dust drawer levers down. 5. Push the dust drawer back into the unit and push dust drawer levers up. 6. Ensure cartridges gaskets are firmly set against the upper part of filter housing Slide the dust drawer out of the unit (6). Lift cartridges off the drawer (7). NOTE : for better and safe performance, use same cartridge material and properties. 17

18 AQC Dust Collecting Systems Replacement of charcoal filter/maxiroll Follow these next steps to replace the charcoal filter. 1. Open cabinet access door. Replacement of charcoal filter/maxicart Follow these next steps to replace the charcoal filter. It is not necessary to open the cabinet access door to replace the charcoal filter. The filter is located behind the clean air outlet at the rear of the unit. 1. Remove the screws holding the air louver into place. 2. Remove the charcoal filter (on left side of unit). Dispose of filter following existing environmental rules and regulations. 3. Slide new charcoal filter on its tracks and close access door. 2. Slide used charcoal filter out of it s track and Dispose of filter following existing environmental rules and regulations 3. Slide new charcoal filter on it s tracks and screw louver back into place. 18

19 Replacement of HEPA filter/maxiroll (optional) 1. Open HEPA filter access door at unit air outlet. Slide filter out and dispose of cartridges in a safe manner and according to environmental regulations. Replacement of HEPA filter/maxicart (optional) 1. Open HEPA filter access door at unit air outlet. Slide filter out and dispose of cartridges in a safe manner and according to environmental regulations. 2. Slide in new HEPA filter. Ensure filter is installed correctly by checking direction of arrow for airflow. 3. Ensure filter frame fits tightly against the filter housing. 2. Slide in new HEPA filter. Ensure filter is installed correctly by checking direction of arrow for airflow. 3. Ensure filter frame fits tightly against the filter housing. 19

20 AQC Dust Collecting Systems Inspection and maintenance The following chart indicates different inspections and frequencies at which they should be observed. Frequency of inspections Components Procedures Empty dust tray. Daily Weekly Yearly Cabinet Filter elements Cabinet Check pressure gauge. If gauge indicates 6 or more, cartridge should be replaced. Ensure motor/fan assembly runs smoothly. Move the Maxair fume arm in different positions for stability (if supplied with the unit). Check for proper installation of cartridge and air leaks. Check for accumulation of dust or debris above and inside the filter elements. Clean if necessary. Proceed with a complete inspection of the unit. Check each filter element status. Replace or clean if necessary. 20

21 Troubleshooting Maxiroll/Maxicart Problems Possible causes Solution Smoke or dust at clean air outlet Cartridge(s) not properly installed. Cartridge is not adjusted properly Cartridge is damaged Damage on seals or gaskets The access door is not shut tight Check installation of cartridge and repair if necessary. Seal all gaskets. (Refer to cartridge replacement section, page ) Ensure drawer levers are completely UP. Replace any damaged filter element. (Refer to cartridge or aluminum spark trap filter replacement section, page 15 et 16. Check seals around the lateral side access door and on filters Make sure access door is properly closed. Insufficient vacuum of contaminents Obstructions on impeller Main cartridge is clogged Aluminum pre-filter or charcoal filter is clogged. Obstruction in Maxair fume arm Fume arm damper is closed Unit is not plugged Check for debris on impeller and remove if present. Remove and replace main cartridge with same media type. (Refer to cartridge replacement procedure in pages ) Clean and/or replace Check for debris in Maxair fume arm. Open damper on fume arm. Plug unit into appropriate electrical outlet. Fan does not work Wiring to the starter is not connected. Check all wiring connections and contacts. Overload has tripped Reset overload. 21

22 Service notes Date Services performed Notes 22

23 AQC Dust Collecting Systems Limited Warranty AQC warrants to the original purchaser that all equipment will be free from defects in materials and workmanship for one year from the date of shipment from AQC, and that major structural components will be free from defects in materials and workmanship for ten years from the date of shipment from AQC. This warranty applies only if equipment is properly installed, maintained, and operated under normal conditions and does not apply to damage caused by corrosion, abrasion, abnormal use or misuse, misapplication, or normal wear and tear. This Warranty will be void with respect to equipment that is subject to unauthorized repairs or modifications. AQC makes no warranty as to goods manufactured or supplied by others. This warranty is subject to any limitations in AQC quotation and may not be modified except by a written instrument signed by the President or Vice President of Sales of AQC. THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, WHETHER WRITTEN, ORAL OR IMPLIED, INCLUDING ANY IMPLED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT. As purchaser s exclusive remedy for any defects in the equipment, AQC will exchange of repair any defective parts during the warranty period, provided such parts are returned, prepaid, to AQC factory. The obligation of AQC is limited to furnishing replacement parts F.O.B. AQC factory or making repairs at AQC factory of any parts that are determined, upon inspection by AQC to be defective. In no event will AQC be responsible for labor or transportation charges for the removal, reshipment of reinstallation of the parts. IN NO EVENT WILL AQC BE RESPONSIBLE FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES. AQC Dust Collecting Systems inc. 660, De La Sabliere Bois-des-Filion, Qc, Canada J6Z 4T7 Tel: (450) Free: Fax: (450) Info@AQCdust.com 23