JOHN DEERE JD1910 TOW BETWEEN GROUND DRIVE Scale System

Transcription

1 JOHN DEERE JD1910 TOW BETWEEN GROUND DRIVE Scale System Installation Instructions And Repair Parts REVA

2 TABLE OF CONTENTS Anamosa, Iowa USA TABLE OF CONTENTS INTRODUCTION... 4 Charging Battery and Welding... 4 SCALE BRACKET AND LOAD CELL MOUNTING INSTALLATION... Removal of Left Side Wheel and Drive Assembly... Installation of Left Side Wheel Assembly and Ground Drive... 7 Spindle and Load Cell Assembly... 7 Counter shaft and drive assembly... 9 Hub Assembly Hub Installation Connecting and Setup of the drive system Installation of Speed Sensor Installation of Wheel onto Axle/Hub Assembly Removal of Right Side Wheel and Axle Assembly Installation of Right Side Wheel and Axle Assembly Spindle Load Cell Assembly Hub Installation Installation of Wheel onto Axle/Hub Assembly Installation of Front Hitch Load Cell Remove Hitch Pintle Receiver REVA Page 2

3 TABLE OF CONTENTS FRONT LOAD CELL HITCH INSTALLATION JUNCTION BOX MOUNTING Four Hole Junction Box INDICATOR MOUNTING RAM MOUNT TESTING AND TROUBLE SHOOTING Inaccurate weights? Erratic weights? OPERATING THE SCALE Filling the Central Fill Monitoring or setting your seed population REPAIR PARTS LICENSE AGREEMENT REVA Page 3

4 INTRODUCTION INTRODUCTION Congratulations on the purchase of your new Scale-Tec Planter Scale System. This scale system is specifically designed to weigh the bulk hopper on a John Deere 1910 Commodity Cart with ground drive. The scale kit can be used to record and monitor seed weight going into or out of the seed hopper. This scale system is covered by the following US patents: , and The singleuse license is included with this document. This SAFETY ALERT SYMBOL indicates important safety messages in the manual. When you see this symbol, be alert to the possibility of PERSONAL INJURY and carefully read the message that follows. NEVER OPERATE WITHOUT ALL COVERS, SHIELDS AND GUARDS IN PLACE. KEEPHANDS, FEET AND CLOTHING AWAY FROM MOVING PARTS. FAILURE TO HEED MAY RESULT INSERIOUS PERSONAL INJURY OR DEATH. Some covers and guards have been removed for illustrative/photographic purposes only in this manual. For information on ordering repair parts, refer to Parts Section in this book. This supersedes all previous published instructions. IMPORTANT! Charging Battery and Welding Disconnect all cables from the weighing indicator before charging the battery or welding on the machine. If cables are left connected, the weighing indicator and connected load cells could be damaged. Important: Do not weld near indicator, load cells or cables; remove from area to be welded. Place ground close to area to be welded to prevent current from passing through electronic parts REVA Page 4

5 SCALE BRACKET AND LOAD CELL MOUNTING INSTALLATION Removal of Left Side Wheel and Drive Assembly NOTE: Prior to starting the installation, you will need at grease to repack the wheel bearings in a later step. Utilize the suggested grease by John Deere to repack the wheel bearings. 1. Raise the left side of the commodity cart with a 20 ton lifting device. 2. Lower the left side of the cart onto blocks so that the wheel is no longer resting on the ground and the full weight of the commodity cart is resting on the blocks. IMPORTANT: Only raise and block one side of the commodity cart at a time. Do not utilze jack as a blocking device. The full weight of the commodity cart should be supported by blocking to prevent jack failure. Should jack fail, death or serious injury may occur. 3. Remove the left side wheel by removing the wheel lugs and separating the wheel rim from the hub of the commodity cart. Rotation Counter Sensor Hub and Axle Assembly Clutch Angle Bracket Clutch Assembly Fig 1 4. Remove the clutch angle bracket by removing the two bolts that hold it in place. This bracket will be reused in a later step. Refer to Figure REVA Page

6 . Remove the drive chain by loosening the chain tightener and removing the chain from the clutch assembly sprocket. 6. Remove the clutch assembly sprocket and flat thrust washer. Set the clutch assembly aside, you will need to reinstall this assembly in a future step. Refer to Figure Remove the rpm speed sensor from the forward portion of the axle assembly. Set the rpm speed sensor aside, you will need to reinstall this sensor in a future step. Refer to Figure Remove the hub and axle assembly. Remove the six bolts that retain the axle assembly to the frame of the commodity cart. IMPORTANT: Utilize a strap and overhead winch that is capable of lifting 1000 lbs. This assembly is very heavy and proper safety percautions should be taken to lower the assembly to the ground. 9. Remove the rear sprocket on the rear of the assembly by removing the two set screws that hold the rear sprocket in place. 10. Remove the 6 bolts that retain the dust cap in place. Drive Shaft/Hub Cap Set Screw Fig REVA Page 6

7 11. Remove the driveshaft/dust cap from the axle assembly. (Utilize a hammer and tap to remove the drive shaft. The drive shaft is attached to the gear. Loosen the set screws and pull the driveshaft/dust cap out from the front of the hub assembly.) NOTE: The Driveshaft/Dust Cap must be returned to Scale-Tec. 12. Remove the bearing retainer nut (castle nut) from the hub assembly. 13. Remove the hub, simultaneously removing the outer wheel bearing from the hub and spindle. Note: care should be taken to not drop the outer wheel bearing, it will be used in later steps. 14. Remove the inner wheel bearing. Note: care should be taken to not drop the inner wheel bearing, it will be utilized in later steps. IMPORTANT! Return the hub and driveshaft/hub cap to Scale-Tec. Failure to return the hub and driveshaft/hub cap to Scale-Tec will result in a core charge. Installation of Left Side Wheel Assembly and Ground Drive Spindle and Load Cell Assembly Fig 3 1. Assemble the left axle counter shaft rear bearing holder assembly (76000). Refer to Fig. 2 a. Install the bearing flanges and bearing to the rear bearing holder (760021). b. Leave the bolts loose until the counter shaft is installed in a later step REVA Page 7

8 2. Assemble the left axle counter shaft front bearing holder assembly (760003). Refer to Fig. 3 a. Install the bearing flanges and bearing to the front bearing holder (760021). b. Leave the bolts loose until the countershaft is installed in a later step. Fig 4 3. Install the left side spindle support ( ) along with the front (760003) and rear (76000) bearing holder assemblies. Secure these items together with the hardware provided and as depicted in figure. Note ensure the top bolts are placed with the bolt passing through the spindle support into the frame of the commodity cart, so that the nut is placed on the back side of the commodity cart. See figure. Fig REVA Page 8

9 4. Insert the load cell spindle (409988) into the left side spindle support ( ). Ensure the TOP sticker is positioned to the top of the load cell, and that you route the wire through the hole positioned in the top center of the left side spindle support. Utilize anti-seize agent to ensure load cells do not rust into place. Note: In order to easily facilitate routing the wire pigtail attached to the load cell, connect the pin connector cable (40710) to the load cell and route as necessary. IMPORTANT: Ensure the TOP sticker is positioned ot the top of the load cell and that care is taken to route the load cell cable through the hole positioned in the top center of the left side spindle support.. Secure the load cell spindle into place with the 1x12 bolt and lock nut provided in the kit. Counter shaft and drive assembly Fig 6 1. Install the counter shaft ( ) through the front and rear bearing support assemblies. 2. Do not tighten the Allen key on the collar, it will be necessary to adjust the counter shaft later REVA Page 9

10 3. Install the flat thrust washer onto the rear side of the counter shaft. 4. Install the clutch/sprocket assembly onto the counter shaft and secure it with a 3/8 x1 bolt. NOTE: DO NOT REUSE THE METRIC BOLT THAT WAS ORIGINALLY ON THE COMMODITIY CART! YOU WILL CROSS THREAD THE SHAFT! Fig 7. Do not tighten the Allen key on the collar, it will be necessary to adjust the counter shaft later 6. Install the sprocket onto the forward side of the counter shaft ( ). 7. Adjust the counter shaft to ensure proper alignment of the clutch/sprocket assembly. 8. Tighten the three bearing holder assembly bolts on both the forward and rear bearing holders. 9. Tighten the Allen keys on the locking collars to secure the counter shaft in proper position. Fig REVA Page 10

11 10. Assemble the gear box (760040) to the gear box support (760044) utilizing the four 3/8 x 1 bolts, 3/8 flat washers, and 3/8 lock washers to secure the gear box to the top portion of the gear box support. 11. Secure the gear box to the left side axle assembly with bolts. Do not tighten; it will be necessary to adjust the gear box support for proper alignment. 12. Install the vertical adjustment 3/8 x 3 ½ bolts with locking nut. Adjust the gear box support (760044) to ensure the gear box is positioned square to the left side axle support. 13. Install the gear sprocket (760019) on the forward side, utilizing a square to ensure proper alignment of the sprocket with the counter shaft sprocket. 14. Install the gear sprocket ( ) on the outer shaft of the gear box (the shaft that will be pointing to the wheel). Do not tighten the sprocket it will be necessary to adjust the sprocket in a future step. Fig REVA Page 11

12 Hub Assembly Note: Utilize the new hub provided with the kit. Place it face down on the ground with the rear portion of the hub facing up to ease the assembly of the hub components. 1. Place short spacer bushings (760047) onto the hub, aligning the holes for correct position. 2. Place the outer drive sprocket onto the short spacer bushings (760049), aligning the holes for correct position. 3. Place the long spacer bushings onto the outer drive sprocket ( ), aligning the holes for correct position. 4. Place the inner sprocket ( ) on top of the long spacer bushings, aligning the holes for correct position.. Secure the sprockets and spacers in place with ½ x 4 bolts and ½ lock washers provided in the kit. Fig 10 Hub Installation 1. Apply grease to the inside cup of the load cell spindle. (Consult with your John Deere Parts Department for approved grease type) It is important that this inner cup is filled completely with grease for proper lubrication. 2. Install the inner bearing onto the load cell spindle. 3. Install the Hub Assembly onto the load cell spindle. 4. Install the outer bearing onto the load cell spindle. Install the bearing retainer nut/castle nut onto the load cell spindle. 6. Prior to installing the cap, utilize approved John Deere silicone to seal the hub. Refer to your John Deere Parts department for the approved silicone. 7. Install the hub cap onto the hub. Fig REVA Page 12

13 Connecting and Setup of the drive system 1. Install the gear box drive chain (760039), ensuring proper alignment. Ensure you utilize the outer sprocket (760049) for installation of the gear box drive chain. Tighten these bolts to adjust and tighten the outer main drive chain. Fig Install the clutch drive chain. It will be necessary to shorten the chain length. Tighten the chain with the original adjustable chain idler on the commodity cart. 3. Install the counter shaft drive chain (760037), ensuring proper alignment. Install the adjustable chain idler sprocket (760019) on the front side counter shaft bearing holder plate, tightening the chain so it is taught and not loose. Fig REVA Page 13

14 Installation of Speed Sensor 1. Install the rpm speed sensor bracket ( ) onto the left side axle assembly. 2. Re-install the rpm speed sensor. Utilize the jam nut provided in the kit to provide proper spacing. 3. Point the speed sensor toward the inner gear on the hub assembly. The proper gap is 0.12 (1/8 ) Proper Gap: 0.12 (1/8 ) Fig Reconnect to the original wire connection on the commodity cart wire harness and route cable as necessary. Installation of Wheel onto Axle/Hub Assembly 1. Install the rim onto the hub aligning the rim with the lug pattern. 2. Secure the wheel rim to the hub with the original lugs. 3. Tighten the lugs to the recommended manufacturer specifications. 4. Unblock and lower the left side of the commodity cart to the ground. Removal of Right Side Wheel and Axle Assembly 1. Raise the right side of the commodity cart with a 20 ton lifting device REVA Page 14

15 2. Lower the right side of the cart onto blocks so that the wheel is no longer resting on the ground and the full weight of the commodity cart is resting on the blocks. IMPORTANT: Only raise and block one side of the commodity cart at a time. Do not utilze jack as a blocking device. The full weight of the commodity cart should be supported by blocking to prevent jack failure. Should jack fail, death or serious injury may occur. 3. Remove the right side wheel by removing the wheel lugs and separating the wheel rim from the hub of the commodity cart. Fig 1 4. Remove the hub cap from the hub by removing the six bolts that retain it in place.. Remove the bearing retaininer nut/castle nut and washer. 6. Remove the hub and outer bearing. Note: take care not to drop the outer bearing on the ground. 7. Remove the axle assembly by removing the six bolts that secure the assembly to the frame of the commodity cart. Fig 16 IMPORTANT: Utilize a strap and overhead winch that is capable of lifting 1000 lbs. This assembly is very heavy and proper safety percautions should be taken to lower the assembly to the ground REVA Page 1

16 Installation of Right Side Wheel and Axle Assembly Spindle Load Cell Assembly 1. Install the right side spindle support by securing it with the six bolts provided. 2. Insert the load cell spindle into the right side spindle support ( ). Ensure the TOP sticker is positioned to the top of the load cell, and that you route the wire through the hole positioned in the top center of the left side spindle support. Utilize anti-seize agent to ensure load cells do not rust into place. IMPORTANT: Ensure the TOP sticker is positioned ot the top of the load cell and that care is taken to route the load cell cable through the hole positioned in the top center of the left side spindle support. 3. Secure the load cell spindle into place with the 1 x12 bolt and lock nut provided in the kit. Hub Installation 1. Apply grease to the inside cup of the load cell spindle. (Consult with your John Deere Parts Department for approved grease type) It is important that this inner cup is filled completely with grease for proper lubrication. 2. Install the inner bearing onto the load cell spindle. 3. Install the Hub Assembly onto the load cell spindle. 4. Install the outer bearing onto the load cell spindle. Install the bearing retainer nut/castle nut onto the load cell spindle. 6. Prior to installing the cap, utilize approved John Deere silicone to seal the hub. Refer to your John Deere Parts department for the approved silicone. 7. Install the hub cap onto the hub. Installation of Wheel onto Axle/Hub Assembly 1. Install the rim onto the hub aligning the rim with the lug pattern. 2. Secure the wheel rim to the hub with the original lugs. 3. Tighten the lugs to the recommended manufacturer specifications. 4. Unblock and lower the left side of the commodity cart to the ground REVA Page 16

17 Installation of Front Hitch Load Cell Remove Hitch Pintle Receiver Fig Remove the bolts and hardware that retains the hitch receiver to the commodity cart. NOTE: Depending on the style of hitch, you may have to remove two or three bolts in order to remove the hitch. 2. Remove the hitch receiver from the commodity Cart 3. Remove the Safety chain from the hitch area. NOTE: Retain the safety chain for installation in a later step REVA Page 17

18 FRONT LOAD CELL HITCH INSTALLATION 1. Insert the load cell into the hitch receiver with the bending arrow sticker at the end of the load cell pointing up. IMPORTANT: ENSURE THE ARROW STICKER ON THE END OF THE LOAD CELL IS POINTING UP! 2. Secure the load cell to the hitch with the 1 x 6 bolt provided in the kit. Torque lock nut to ft/lbs 3. Insert the load cell into the hitch weldment (760024) and secure it with a vertical bolt 1 x. Torque lock nut to ft/lbs 4. Align the hitch weldment with the frame hole pattern on the commodity cart. Install the two 1 x 9 bolts in the upper two holes of the weldment. Torque lock nut to ft/lbs.. Install the 1 x 10 bolt in the lower hole of the weldment and secure the safety chain to the frame of the commodity cart. Torque lock nut to ft/lbs REVA Page 18

19 JUNCTION BOX MOUNTING Four Hole Junction Box The junction box is water resistant, not water-proof. It should be mounted to avoid submersion during wet weather and to avoid physical abuse. The junction box can be mounted on the front or rear of the drill, planter or seeder. All load cell cables must reach the J-Box. Install by removing the double sided tape backing and apply to cleaned surface. Connect Load Cell and Junction Box Cable 1. Route front and rear load cell cables to J-box location. Make sure they are not bound or pinched. Cable tie (Customer provided) load cell cables in place. 2. Insert load cell and J-box cables through each of the water-tight strain-reliefs. 3. Remove each terminal block from the J-box. 4. Connect wires of the same color to the same terminal block as shown above. See instructions below.. Install terminal block into the J-box as shown (location not important). 6. Tighten nuts on the water-tight strain-reliefs. 7. Assure that gasket is properly installed in the cover. 8. Attach cover using 4 screws (provided). Installing Wires into Terminal Block 1. Open levers 90º to locked position. 2. Insert individual wires into terminal. 3. Close lever. 4. Tug wire to assure solid connection. Note: Wire strip length is 7/16 (11mm) REVA Page 19

20 Indicator Mounting INDICATOR MOUNTING RAM MOUNT The scale indicator can be mounted in the tractor cab or on the drill with swivel mounting pack (406081). Two cables must be connected to the indicator bottom panel, J-Box and power cables. Refer to Indicator Manual D3831-US for details of indicator mounting options and connection of power cord. INDICATOR MOUNTINGS PLANTER MOUNTING TRACTOR CAB MOUNTING a. Bolt the readout in the cab with the bracket, or mount the bracket in the front of the lift cylinder. b. Install power cord to a 12-volt negative ground battery. c. Route J-box cable to indicator and install to indicator bottom panel. Power Connection: The power cable should be connected directly to a vehicle battery or regulated power supply. The scale end of the power cable is attached to the J901 connector located on the bottom panel of the indicator. Connect the RED wire from the power cable to +12 VDC and the BLACK wire to GROUND. The indicator is fused internally at 4 amps. Power Cable Connections: Wire Color Red Black Wire Function Battery (+12 VDC) GROUND REVA Page 20

21 Testing and Trouble Shooting TESTING AND TROUBLE SHOOTING IMPROTANT All bars need to weigh accurately before it will be beneficial to recalibrate your indicator Inaccurate weights? 1) Measure the same person, or a 200 pound bag of seed, on each of the weigh bars. If one weighs negative, turn that weigh bar over. (An upside down bar will weigh negative.) If one side is weighing 20% light, check for an obstruction. Is anything binding or any metal rubbing? Could be a faulty weigh bar If they are all even weights, but are weighing light or heavy, you need to adjust the calibration. If your scale is more than % off, call us for help, as your scale may have had the wrong calibration number put in it from the factory The hopper being weighed needs to be at least ¾ full for us to adjust calibration. Check operator s manual or give us a call at Erratic weights? The following process needs to occur in an effort to eliminate one part at a time in an effort to find the problem! When you reconnect the faulty part you will have erratic readings again. 1) Disconnect the junction box cord from the indicator marked load cells. The indicator should stabilize after 4 seconds. Try to zero out the indicator. IF the indicator won t zero out, the indicator is the problem. IF it will zero out: 2) Connect the junction box back to the indicator. And then disconnect all of the load cells from the junction box. 3) Zero out the indicator. IF the indicator won t zero out the problem is the junction box or the junction box cable. IF it will zero out: 4) Reconnect the load cells ONE AT A TIME, zeroing out the indicator each time. When you reconnect the faulty load cell, you will have erratic readings again REVA Page 21

22 Operating the Scale OPERATING THE SCALE Filling the Central Fill NOTE: The example given uses 2000 lbs of seed evenly filled in both hoppers. There is 2 lbs of seed left from the last fill. 1. Push the "Start" button. The screen will show zero, and the arrow is now pointing to "Net" on the screen. This is a temporary zero point to start loading the planter with seed. You will now fill 1000lbs of seed into the left hopper. 2. Push the "Stop" button, the readout will display 102 lbs of seed inventory. 3. Push the "Start button again. The screen will say zero again. Load another 1000 lbs of seed into the right side. 4. Now push "Stop" and the screen will read 202 lbs of seed. As planting occurs the weight displayed will decrease. Monitoring or verifying your seed population There are two methods to monitor rate of material being applied. Method 1: 1. Fill only one hopper full of product/seed. 2. Press the Start button when ready to apply. 3. Apply acres of product to the field and stop in a level/stationary position. 4. Read the amount of product/seed dispensed.. Make necessary adjustments as required. Method 2: 1. Fill Hopper one with a determined amount of product. 2. Fill hopper two/three with a determined amount of product with more weight than hopper one. 3. Apply product/seed until hopper one runs empty. 4. Verify product rate of hopper one and make adjustments as necessary.. Verify product rate of hopper two/three and make adjustments as necessary REVA Page 22

23 Repair Parts REPAIR PARTS 1, ,7, ,7, ,7, REVA Page 23

24 Repair Parts KEY QTY. PART NO. DESCRIPTION KEY QTY. PART NO. DESCRIPTION 1 3 STB3-8X3 BOLT- 3/8 X 3 Grade 27 2 STN1 NUT-LOCK STN3-8 NUT- 3/ KEYSTOCK- /16 X /16 X 1 ½ GEAR BOX- 90 Transfer 29 1 STFLN1-2 NUT-FLANGE LOCK ½ WELD- Gear Box Support CABLE- EZMATE FEMALE 21FT CELL- 6.0 SA 8 EZMATE 31 1 A8687 REUSE OEM, NOT INCLD 6 12 STB3-8X1 BOLT- 3/8 X 1 GRADE 32 2 STB1X12 BOLT- 1 X STW3-8 WASHER-FLAT 3/ SHAFT- COUNTER DRIVE 8 10 STLW3-8 WASHER- LOCK 3/ H166 REUSE OEM, NOT INCLD KEYSTOCK- ¼ X ¼ X 1 ½ 3 1 CLUTCH REUSE OEM, NOT INCLD CHAIN- #60 ROLLER 36 1 STB3-8X11-2 BOLT - 3/8 X 1 ½ (CONNECTORS INCLUDED) 11A WELD- LT SPINDLE SUPPT 37 19M7784 REUSE OEM, NOT INCLD 11B WELD- RT SPINDLE SUPPT 38 1 *76003 CAP- DUST w/o DRIVE SHAFT 12 1 A61237 REUSE OEM, NOT INCLD 39 1 * HUB- JD1910 BORED WITH TRIGGER WHEEL SUPPORT BRKT- RPM SENSOR SPACER- SHORT DOM NUT- RPM SENSOR SPROCKET- DRIVE # AA47936 REUSE OEM, NOT INCLD CHAIN- #80 ROLLER (Connectors included) SPROCKET-#60 1 BORE SPROCKET-#80 1 BORE SPROCKET- #60 IDLER SPACER- LONG DOM 18 1 STCB1-2X21-2 BOLT-Carriage ½ X 2 ½ SPROCKET- TIMING SPEED STW1-2 WASHER- FLAT ½ 46 STLW1-2 WASHER- LOCK ½ 20 8 STFLN3-8 NUT-FLANGE LOCK 3/8 47 STB1-2X4 BOLT- ½ X STCB3-8X1 BOLT-Carriage 3/8 X HOLDER- REAR BEARING Bearing/Flange Kit HOLDER- FRONT BEARING NUT- LOCK 20MM Bolt- 20MM x 70MM SPROCKET-#60 1-3/8 BORE 26 4 STW1 WASHER- FLAT REVA Page * Yellow color indicates John Deere Parts reused during installation and are not provided in the kit. *Only one hub and hub cap is provided in the kit for the left side installation. Reuse original hub and cap on the right side. Left Side hub and cap shall be returned to Scale-Tec.

25 Repair Parts KEY QTY. PART NO. DESCRIPTION 1 2 STB1X9G9 BOLT- 1 X 9 Grade STB1X10G9 BOLT- 1 X 10 Grade STB1XG9 BOLT-1 X Grade 9 4 STLN1 NUT-LOCK WELD-HITCH STB1X6G9 BOLT- 1 X 6 G CELL DB-16 4.SA RECEIVER HITCH- CAST 2 7/ REVA Page 2

26 Repair Parts KEY QTY. PART NO. DESCRIPTION Brkt Robo Mtg Brkt Swivel Cast (JD H161618) Gasket 1.813OD x ID x.313 WID Scr 1/4-20 x 3/4 HHCS ZP Washer Lock 1/4 ZP Nut 1/4-20 ZP Scr 3/8-16 x 3.0 HHCS ZP Grd Nut 3/8-16 Nyloc ZP GT400 Indicator (Not included in kit ) KEY QTY. PART NO. DESCRIPTION Ram Suction Cup with Twist Lock Assembly 1 Ram Mount Scr - #10 x /8 PHSTS 48-2 Blk ZP REVA Page 26

27 License Agreement LICENSE AGREEMENT IMPORTANT NOTICE: Acceptance and use of the enclosed electronic scale products (hereinafter referred to as Purchased Product ) constitutes your agreement to the following terms and conditions. Please carefully read the following terms and conditions before using or reselling the Purchased Product. 1. Limited License. Digi-Star, LLC, a Wisconsin limited liability company ( Owner ) is the owner of the following U.S. Patents related to grain drills: 6,732,667, 7,09,28, 7,273,017, 7,37,087, 7,448,33, 7,23,710 and any other patents which result from continuation applications thereof ( Patents ). Owner hereby grants to the customer ( Customer ) a non-exclusive, non-transferable, revocable, limited license to use the technology described in the Patents to use the Purchased Product to assemble a seed planter product covered by the Patents ( Licensed Product ), and to sell and offer for sale one (1) unit of the Licensed Product in accordance with the terms and conditions set forth herein. Alternatively, Customer may resell the Purchased Product to another entity for the purpose of that entity assembling one (1) unit of a Licensed Product under a permitted sublicense from the Customer with the same terms as this Agreement. If Customer would like to assemble, use, sell or offer for sale more than one (1) Licensed Product, or resell more than one (1) Purchased Product, Customer understands and agrees that it must purchase another Purchased Product from Owner or acquire a separate license by requesting and purchasing another unit of the same SKU number that resulted in this purchase. 2. Acceptance of Terms and Conditions. Customer warrants that it has the authority to enter into this binding agreement. If Customer does not accept the terms and conditions, Customer shall not use the Purchased Product. Customer understands and agrees that if it uses the Purchased Product as permitted herein, it will be deemed to have accepted these terms and conditions and they shall become a binding agreement. 3. Limitations on Use. Customer agrees that it will use the Licensed Product only as expressly authorized in this Agreement, and that any use not expressly authorized in this Agreement is prohibited. Customer agrees that it will not: (i) loan, rent, lease, assign, sublicense, distribute or otherwise transfer its rights under this Agreement to a third party, other than to resell the Purchased Product to another entity for the purpose of that entity assembling one unit of a Licensed Product; (ii) copy or reproduce the Licensed Product; or (iii) grant any sublicenses other than to an end user of the Licensed Product, or to another entity for the purpose of that entity assembling one unit of a Licensed Product. Customer agrees to use reasonable efforts to prevent any unauthorized use or copying of the Licensed Product and will notify Owner immediately upon learning of any such unauthorized use or copying. Customer s obligations under this section shall survive any termination of this Agreement or the license granted hereunder. Any unauthorized use of the Licensed Product will result in, among other things, the immediate termination of this license. 4. Ownership of Proprietary Rights. Customer acknowledges that the Licensed Product is covered intellectual and/or proprietary rights, and that all such intellectual and proprietary rights are owned by Owner. Customer hereby acknowledges that it has no rights in the foregoing except as expressly granted herein.. NO WARRANTY. Customer agrees to fully test and evaluate the Purchased Product and Customer acknowledges and agrees that Owner will not assume any product liability or any other liability for the Purchased Product or the Licensed Product. The Purchased Product is furnished to Customer AS IS. Except as otherwise provided by separate documentation, OWNER MAKES NO WARRANTIES, EITHER EXPRESS OR IMPLIED, WITH RESPECT TO THE PURCHASED PRODUCT. Customer agrees that Owner shall have no liability resulting from Customer s use of the Purchased Product for any indirect damages including consequential, incidental or special damages for loss of profit, good will or otherwise. Customer shall indemnify and hold Owner harmless from any and all losses, expenses, damages, costs or expenses of any kind, including but not limited to reasonable attorneys fees, incurred by Owner resulting from Customer s use of the Purchased Product. NO ORAL OR WRITTEN STATEMENTS MADE BY OWNER OR ITS EMPLOYEES INCLUDING BUT NOT LIMITED TO STATEMENTS REGARDING CAPACITY, SUITABILITY FOR USE, OR PERFORMANCE OF THE PURCHASED PRODUCT SHALL BE DEEMED A WARRANTY OR REPRESENTATION BY OWNER FOR ANY PURPOSE NOR GIVE RISE TO ANY LIABILITY OR OBLIGATION OF OWNER. 6. Remedies for Violations. Owner reserves the right to seek all remedies available at law and in equity for violations of this Agreement, including but not limited to the right to recover the Licensed Product. 7. Fees. In consideration for the rights granted under this Agreement, Customer has paid a license fee that was included in the amount invoiced to the Customer for the sale of the Purchased Product. 8. Entire Agreement. Except as expressly stated herein to the contrary, this Agreement constitutes the entire agreement between the parties regarding the subject matter hereof, and no verbal or written prior statements or representations of any sort made by any party shall be effective or valid for any purpose whatsoever. This Agreement may be amended only upon the mutual consent of all parties in writing. 9. Severability. If any provision of this Agreement shall be held to be invalid, illegal or unenforceable, the validity, legality and enforceability of the remaining provisions shall not in any way be affected or impaired thereby. The failure of any party to enforce any provision of this Agreement shall not be considered a waiver thereof, nor shall such failure prevent the future enforcement of any such provision. 10. Governing Law. This Agreement and the relationship between the parties shall be governed in all respects by the laws of the State of Wisconsin and the United States of America. The parties consent to the jurisdiction and venue of the Wisconsin and United States courts located in Wisconsin for resolution of any dispute under to this Agreement. Use or sale of the Licensed Product or of Purchased Product shall bind Customer to all terms and conditions herein without the necessity of signatures on this Agreement REVA Page 27