INSTRUCTION MANUAL TYPE 088A

Transcription

1 INSTRUCTION MANUAL for the TYPE 088A SEMIAUTOMATIC BAG CLOSER TYPE MODEL SERIAL NO. 088A 10 10

2 SECTION CONTENTS PAGE I SPECIFICATIONS II OPERATION III ADJUSTMENTS IV TROUBLE SHOOTING V PARTS IDENTIFICATION VI WIRING DIAGRAM Appendix...A. Bag length formulas B-J. Optional bag neck trimmer K. Suggested spare parts L. Returned Materials Authorization GENERAL SAFETY INFORMATION Be sure the following safety instructions are read, understood and become a part of daily practice when operating or maintaining the closer. 1. Do not attempt to operate the closer until you understand its function. Study the manual carefully. 2. Electricity is potentially dangerous. Do not remove the machine covers. There are exposed electrical components within that can cause serious electrical shock. All maintenance and adjustments must be performed by competent personnel. 3. Always tighten the knob to secure the closer to the stand. If the closer is allowed to rotate on the stand, it may come out of balance and tip over. 4. Keep any foreign material and fingers away from moving parts KWIK LOK CORPORATION ALL RIGHTS RESERVED Kwik Lok and Striplok are trademarks of Kwik Lok Corporation The shape of the closure is a trademark of Kwik Lok Corporation A 09 10

3 SECTION I Specifications THE TYPE 088A MACHINE SEMIAUTOMATICALLY CLOSES BAGS WITH THE STRIPLOK CLOSURE AND CLOSURE LABEL A. The 088A semiautomatic bag closing machine closes packages with the NRP style Striplok bag closures and Striplok bag closure-labels. B. The 088A closer will close various package widths without adjustment. Package width limitations are determined by the closure opening. C. The system will close a wide range of product size variations. The Striplok closures are available in many closure opening sizes to accommodate a large number of variations in bag widths and film thicknesses. D. Maximum package weight listed is based on factory approved closure opening size. Upon request and receipt of sample bags, the factory will gladly recommend the proper closure opening sizes. Use the bag length formula found in the appendix, page A of this manual to help determine the proper bag length needed. E. A suggested spare parts inventory is listed on page K in the appendix. To save valuable time, it is recommended that an adequate supply of these parts be kept on hand for needed repairs. 088A P 1.1

4 SECTION I Specifications MODEL DESIGNATION PRINTER PACKAGE SPEED AVAILABLE CLOSURES TYPE PREFIX CLOSURE FLOW WEIGHT (BAGS/MIN) AND CLOSURE LABELS 088A A K-NRP R or L No J-NRP, K-NRP, PF, TF, P-200, T-220, CFJ 088A A KM-NRP R or L No Up to 5 Lbs. JM-NRP, KM-NRP, PFM (2.3 Kg.) 50 TFM, PM-200, TM A AP K-NRP R or L Yes J-NRP, K-NRP, PF, TF, P-200, T-220, CFJ 088A AP KM-NRP R or L Yes JM-NRP, KM-NRP, PFM, TFM, PM-200, TM-220 *Refer to the INSTRUCTION MANUAL for the PRINTER FEATURE of the TYPE 088A APR SEMIAUTOMATIC BAG CLOSER TYPICAL APPLICATIONS Bakery products, candy, snack foods, puffed wheat, potato salad, meat patties, auto and bicycle parts, filters, flower bulbs, popsicles. SPECIFICATIONS HEIGHT (Maximum):...38 (96cm) WIDTH:...13 (33cm) LENGTH:...22 (56cm) AVAILABLE ELECTRICAL POWER (As ordered) 100 VAC, 50/ 60Hz, 1.0 Amp, 1 Phase 115 VAC, 60Hz, 1.0 Amp, 1 Phase 230 VAC, 50/60Hz, 0.5 Amp, 1 Phase PRINTER OPTION REQUIREMENTS Air Volume and Pressure: 1.5SCFM at 120 psi (6 liters/min at 8 BAR) Maximum Air Pressure: 150 psi (10 BAR) Printing supplies: Order separately from your type supplier. Kwik Lok recommends CODEMARK products. APPROXIMATE SHIPPING SPECIFICATIONS WITHOUT PRINTER WITH PRINTER DIMENSIONS 30 X 24 X X 24 X 20 76cm X 61cm X 51cm 97cm X 61cm X 51cm VOLUME 8.4 Cubic Feet 10.6 Cubic Feet 0.24 Cubic Meters 0.30 Cubic Meters WEIGHT 45 Pounds 65 Pounds 21 Kilograms 30 Kilograms P A 09 10

5 SECTION I Specifications The 088A closer is available in right or left-hand models. Refer to the illustration below to establish if your machine is a right or left-hand. 088A Left-hand closer 088A Right-hand closer 088A P 1.3

6 SECTION I Specifications CLOSURE AND CLOSURE LABEL IDENTIFICATION (CLOSURES AND CLOSURE LABELS ARE SHOWN AT FULL SCALE) The 088 Closer is available in right-hand as well as left-hand models. Any Kwik Lok closure (without a label) will run through either a right-hand or a left-hand closing machine. All Kwik Lok closure labels are manufactured as a right-hand or left-hand to fit the hand of the machine being used. P 1.4 Figure A 02 10

7 SECTION I Specifications CLOSURE AND CLOSURE LABEL IDENTIFICATION (CLOSURES AND CLOSURE LABELS ARE SHOWN AT FULL SCALE) The 088 Closer is available in right-hand as well as left-hand models. Any Kwik Lok closure (without a label) will run through either a right-hand or a left-hand closing machine. All Kwik Lok closure labels are manufactured as a right-hand or left-hand to fit the hand of the machine being used. JM-NRP or KM-NRP CLOSURE PFM LABEL (LEFT-HAND) PFM LABEL (RIGHT-HAND) TFM LABEL (LEFT-HAND) TFM LABEL (RIGHT-HAND) Figure A P 1.5

8

9 SECTION II Operation PRINTER OPERATING SEQUENCE: CLOSER SEQUENCE: 1. When a bag top is presented into the drive belts, the continuously-running belts propel the bag top forward and gather it into the opening of the closure. A. POWER REQUIREMENTS: Electrical power needs should be determined when the machinery order is placed. Refer to Specifications, Section I. 2. As the bag film moves along the bag path, it swings the actuator lever to the side which opens the contacts of the magnetic sensor. 3. As the trailing edge of the bag clears the actuator lever, the lever spring-returns to the rest position and closes the contacts of the magnetic sensor. 4. The solenoid module detects the closed contacts and sends an electrical pulse to the clutch solenoid to rotate the single-revolution clutch. 5. During the first half-revolution of the clutch, a cam on the clutch shaft rotates the breakoff lever to detach the closure from the closure strip and then returns the lever to the rest position. Figure 2.1 Closer mount knob 6. At the same time, an eccentric linkage slides the pick backward so it can engage the next closure in the closure track. The check restricts the closure strip so that the pick does not drag the strip backward in the closure track. 7. During the second half revolution of the clutch, the pick moves forward to advance the next closure to the proper position to receive the next bag top. 8. The bag closing sequence ends when the clutch stops. 9. To manually cycle the closer without presenting a bag to the drive belts, the operator can depress and release the green manual push button. The separated closures, if present, must be removed by hand. B. ADJUST CLOSER HEIGHT: Figure 2.1 Mount the 088 closer onto the mounting post and clamp the closer to the post. NOTE: The closer can be mounted over a lower mounting post or from a mounting post from above and then clamped to it (Figure 2.1 illustrates the closer mounted on a post from below). Close a few packages until the desired package tightness is achieved. Set the height of the closer so the product being closed just clears the top of the mounting surface as the package feeds into the closer. Optional bag guides may be used when feeding product into the closer. 088A P 2.1

10 SECTION II Operation E. MOUNTING A ROLL OF CLOSURE-LABELS: Figure Release the front latch located at the center of the front reel plate and remove the label reel cassette from closer. 2. Release the two latches located on the back side of the cassette assembly and separate the cassette. 3. Remove and discard the closure-label core, and reload it with a new roll of closure-labels. (Closure-labels must always be mounted with the closure opening facing the oncoming product). C. CLOSURE GUIDE SHIM: Figure 2.2 and 2.8 Figure 2.2 The closure guide shim is required only when closures are being used. The shim must be removed when using closure-labels. The shim is held in the track by a spring clip and can be removed easily by hand. Failure to replace the shim when closures are used can result in closures being dislodged from the closure track. When the shim is removed from the closure track it can be stored on the back of the lower cover. 4. Replace the reel plate and press the two latches down to lock the cassette together. 5. Slide the full cassette onto the label reel axle and press the locking latch down to secure the cassette to the axle. D. MOUNTING A ROLL OF CLOSURES: Figure Grasp the reel knob located on the front reel side plate and pull the outside reel plate off the reel detent pin. 2. Mount a roll of closures on the reel hub bearing. (Closures must always be mounted with the closure opening facing the oncoming product). 3. Replace the reel side plate. Figure 2.3 P A 10 05

11 SECTION II Operation Figure 2.5 Figure 2.4 NOTE:It is recommended that a multiple number of reel cassettes be used for faster installation of closurelabels, or for storage of partially used rolls. F. FEEDING CLOSURES INTO THE CLOSURE TRACK: Figures Remove the tape from the roll of closures. 2. Insert the free end of the closure strip into the slot of the closure track. NOTE: THE CLOSURE OPENING MUST FACE THE ONCOMING PRODUCT. THE NRP SERIES CLO- SURE STRIP MUST BE INSERTED AS SHOWN IN FIGURE 2.6 AND 2.7. NOTE THE BACK OF THE WEB OF THE END CLOSURE IS FREE TO EXIT PAST THE REMAINING CLOSURE STRIP. 3. Insert the closures into the track until the end of the strip contacts the lok pick. Make sure the lok check is in the slot between the closures, in the down (engaged) position. 4. Press and release the green manual cycle button to automatically advance the closures into a ready-to-close position. Continue to cycle until there is a closure in the closing position. WARNING: IT IS ADVISABLE TO MANUALLY INSERT A BAG TO BREAK OFF AND REMOVE CLOSURES FROM THE TRACK. WITHOUT A BAG TO TAKE AWAY THE CLOSURE(S), JAMMING CAN OCCUR DUE TO CLOSURES STACKING UP AT THE END OF THE LOK TRACK. 088A P 2.3

12 SECTION II Operation G. CHANGING FROM CLOSURES TO CLOSURE- LABELS: Figures 2.5, 2.6 and Rotate the breakoff lever by hand to break off the end closure. Flip the check so it is disengaged from the closure strip. 2. Push down on the black pick release knob and pull the closure strip out of the closure track. 3. Remove the closure guide shim and hang it on the back of the lower cover. (DO NOT DISCARD). 4. Hand feed closure-labels into the closure track until they contact the lok pick. Make sure the lok check is engaged. 5. Cycle the closer to feed the closure-labels into the ready-to-close position. Figure 2.6 Figure 2.7 P A 12 04

13 SECTION II Operation H. CHANGING FROM CLOSURE-LABELS TO CLOSURES: Figures 2.5, 2.6 and Rotate the breakoff lever by hand to break off the end closure. Flip the check so it disengages from the closure strip. 2. Push down on the black pick release knob and pull the closure strip out of the closure track. 3. Replace the closure guide shim. The shim will snap into position. 4. Feed closures into the track until they contact the lok pick. Make sure the check is engaged. 5. Cycle the closer to feed the closures into the ready-to-close position. I. PRESENTING THE BAG TO THE CLOSER: The condition of the closed package is dependent upon the manner in which the bag is fed into the closer. For best results observe the following: 1. Determine that the length of the bag is correct. Refer to the Bag Length Formula in the appendix. If the height of the product in the bag will vary, or if it is desirable to remove the wicket lip from the bag tops, consider using the optional bag neck trimmer. 2. Determine how the bag will be presented to the closer at the proper height. Consider placing the package on a conveyor below the closer to position the bottom of the package; or use the Closure guide shim Figure 2.8 optional bag guides to position the height of the top of the product. For wide bags, the guides may need to be spaced lower than the normal position. If the closure is placed too high on the bag, the package may appear loose or under filled. If the closure is placed too low on the bag, the bag may be marked, torn, not closed completely, or the product may be damaged by the closer. 3. Present the bag so the closer can grip the leading edge and gather the remainder of the bag top. Do not intentionally gather or twist the bag top. A few wrinkles will not be a problem. For wide bags it may be necessary to use both hands to spread the bag top. 4. Release the bag top as it enters the belts of the closer. Do not pull forward on the bag top. 088A P 2.5

14

15 SECTION III Adjustments This section provides step by step directions for all adjustments on the 088A closer. Use the following table of contents to quick reference a particular adjustment. A. REPLACE OR ADJUST THE UPPER IDLER BELT. B. REPLACE OR ADJUST THE UPPER DRIVE- BELT. C. REPLACE OR ADJUST THE LOWER IDLER BELT. D. REPLACE OR ADJUST THE LOWER DRIVE- BELT. E. REPLACE OR ADJUST THE CLUTCH DRIVE- BELT. F. REMOVE THE CLOSURE TRACK. G. BREAKOFF CAM POSITION. H. CLUTCH SOLENOID ADJUSTMENT. I. BREAKOFF ARM ADJUSTMENT. J. CLOSURE POSITION. K. PICK POSITION. L. LOK CHECK. M. BAG FILM GUIDE. N. ACTUATING LEVER SWITCH. O. PULLEY POSITIONS. Belts should be checked periodically for wear. It is also important to keep the correct tension on the belts. A. REPLACE OR ADJUST THE UPPER IDLER BELT: Figure 3.1 and Disconnect the 088 Closer power cord from the electrical source. 2. Remove the two mounting screws from the upper idle side belt assembly. Note the position of the nylon washers. 3. Disconnect the tension spring from the spring anchor point and remove the belt assembly. 4. Loosen the mount screw for the front pulley, and slide to remove the belt tension. 5. Remove the belt. Figure Use a brush to clean the teeth of the pulleys. 7. Replace and tension the belt. Tighten the mount screw. 8. Place one nylon washer above and below the pivot plate at each of the two mounting screw locations. 088A P 3.1

16 SECTION III Adjustments Idle side slot Idle side pivot Block the idle side slot P 3.2 Figure Attach the tensioner spring, and remount the upper idle belt plate. Leave the mounting screws slightly loose. 10. Tighten the pivot screw just enough to allow the mounting plate spring tension to pull the idle belt up against the upper drivebelt. Tighten the back mounting screw slightly to allow the idle belt assembly to pivot. B. REPLACE OR ADJUST THE UPPER DRIVE- BELT: Figures Disconnect the 088 Closer power cord from the electrical source. 2. Pivot the upper idle belt assembly away from the upper drivebelt assembly. Use the edge of a closure to block the idle side slot (Figure 3.3) so the spring tension being applied to the idle side belt assembly does not affect the following adjustments. 3. Remove the two top covers of the closer. Note the screw lengths for each screw location. 4. Release the upper drivebelt tension at the tensioner pulley. Move the tensioner pulley approximately 1/4 (6 mm) inch away from the belt and slightly tighten the pulley in the mounting slot. Relieves pinch force here Figure Remove the three remaining mounting screws from the drive plate assembly. 6. Replace the upper drivebelt if needed and clean out any residue found in the pulleys. NOTE: To properly set the pinch point for the top belts, the upper idle side belt assembly must be in place and blocked. 7. Replace the four mounting screws including the one that attached the right top cover and leave them slightly loose. 8. Press the front of the upper drive plate assembly against the upper pivot plate assembly so the front of the drivebelt lightly comes into contact with the upper idle belt. 9. Maintain this position between the upper drive and upper idle belts as the four upper drive plate mounting screws are tightened. 088A 10 05

17 SECTION III Adjustments Figure 3.4 Figure A P 3.3

18 SECTION III Adjustments 10. Tension the upper drivebelt using the belt tensioner pulley. Apply a light tension to the drivebelt. Manually turn the drive pulley to align the drivebelt to the pulleys and again check the tension on the belt. 11. Replace the two top covers. The pivot screw of the upper drive plate doubles as a screw for the back cover. Remove the pivot screw, and position the back cover onto the closer. Replace the pivot screw through the back cover. C. REPLACE OR ADJUST THE LOWER IDLER BELT: 1. Disconnect the 088 Closer power cord from the electrical source. 2. Remove the idle front nose guard. 3. Remove either the large shield from the side of the closer or the upper idle belt assembly. 4. Remove the two mounting screws and Esna nuts from the lower idle side belt assembly. Note the position of the nylon washers 5. Disconnect the tension spring from the spring anchor point and remove the idle belt assembly. 6. Loosen the mount screw for the front pulley, and slide to remove the belt tension. 7. Remove the belt. 8. Use a brush to clean the teeth of the pulleys. 9. To replace the belt, loosen only one of the two pulleys. Replace and tension the belt. 10. Place one nylon washer above and below the pivot plate at each of the two mounting screw locations. 11. Remount the tensioner spring, and remount the lower idle belt plate. Leave the two mounting screws slightly loose. 12. Tighten the pivot screw just enough to allow the mounting plate spring tension to pivot the idle belt assembly into the normal operating position. Tighten the back mounting screw slightly to allow the lower idle belt assembly to pivot under the spring tension. 13. Install the nose guard. D. REPLACE OR ADJUST THE LOWER DRIVE- BELT: 1. Disconnect the 088 Closer power cord from the electrical source. 2. Remove the drive front nose guard. 3. Pivot the lower idle belt assembly away from the lower drivebelt assembly. Use the edge of a closure to block the idle side pivot point so the spring tension being applied to the idle side belt assembly does not affect the following adjustments. 4. Release the lower drivebelt tension at the tensioner pulley. Move the tensioner pulley approximately 1/4 inch (6 mm) away from the belt and slightly tighten the pulley in the mounting slot. 5. Remove the two mounting screws from the drive plate assembly. Note the two nylon washers beneath the plate. 6. Loosen the mount screw for the front pulley and slide to remove the belt tension. 7. Replace and tension the lower drivebelt. Remove any residue found in the pulleys. NOTE: To properly set the pinch point for the lower drivebelt, the lower idle side belt assembly must be in place and blocked. 8. Replace the two mounting screws, and nylon washers. Leave the mounting screws slightly loose. P A 09 10

19 SECTION III Adjustments Figure Press the lower drive plate assembly against the lower pivot plate assembly so the front of the drivebelt lightly contacts the lower idle belt. 10. Maintain this position between the lower drive and lower idle belts as the lower drive plate mounting screws are tightened. 11. Install the nose guard. E. REPLACE OR ADJUST THE CLUTCH DRIVEBELT: Figure Disconnect the 088 Closer power cord from the electrical source. 2. Remove the two top covers from the closer. Note the length of the mounting screws for reassembly. 088A Release the tension on the upper and lower drivebelt assemblies at the tensioner pulleys. Move the tensioner pulleys approximately 1/4 inch (6.4mm) away from the belt and slightly tighten the pulley in the mounting slot. 4. Remove the three x 1 3/4 inch socket head cap screws from the main drive pulley and remove the pulley from the motor shaft. The lower pulley remains on the motor shaft. 5. Carefully disconnect the two wire connectors from the clutch actuating solenoid. 6. Remove the reel assembly. 7. Remove the closure track (see part F below). 8. Loosen the clutch drivebelt tensioner pulley. Slide the pulley assembly out of the way and retighten the mounting screw. P 3.5

20 SECTION III Adjustments 9. Turn the closer over and remove the stand. 10. Remove the lower cover. Note the screw lengths as they are removed. 11. Remove the x 3/8 socket button head screw, washer and spring from the end of the breakoff camshaft. 12. Remove the two x 1/2 inch socket button head screws from the two long clutch mounting posts. 13. Remove the clutch mounting plate and bearing from the camshaft. 14. Loosen the 8-32 socket head screw (or button head screw) located at the bottom end of the camshaft and allow the clutch to drop down against the closer main frame. 15. Work the drivebelt off the clutch pulley and remove the clutch assembly from the breakoff camshaft assembly. The breakoff camshaft remains attached to the breakoff linkage. (Note the bushing on the camshaft). 16. Remove the clutch drivebelt. 17. Place the new belt around the motor pulley and around the breakoff camshaft. 18. Note the flat located on the breakoff camshaft. The 8-32 socket head screw must seat against this flat on the shaft when remounting the clutch assembly. 19. Slide the clutch assembly onto the camshaft with the clutch pulley facing down. 20. Work the clutch drivebelt onto the clutch pulley. 21. Replace the button head screw, washer, and spring to the bottom of the breakoff camshaft. 22. Remount the clutch mounting plate to the two long mounting posts and tighten. 23. Allow the clutch assembly to drop down onto the bearing in the mainframe. Tighten the 8-32 socket head screw to the breakoff camshaft noting that the screw should seat on the flat of the camshaft. 24. Turn the closer right side up. Apply very light pressure to the clutch drivebelt with the tensioner pulley and tighten the tensioner pulley. The drivebelt must not apply side load to the clutch. 25. Reconnect the two electrical leads to the clutch solenoid. 26. Check the top drive and the bottom drivebelt routing to be sure the two belts are routed correctly. 27. Slide the two belts onto the main drive pulley and remount the main drive pulley onto the motor shaft. Align and tighten the three mounting screws through the main drive pulley and into the motor pulley. 28. Readjust the tension to the two drivebelts and tighten down the tensioner pulleys. 29. Replace the bottom cover and remount the closer to the stand and return the closer to its upright position. 30. Slide the closure track back into position on the closer. Align the bushings under the two mounting holes in the lok track. Be sure that the spring pin located in the front of the pick is positioned under the pick release plate. Tighten the closure track to the mainframe. 31. Reattach the breakoff return spring. Replace the two top covers and the reel assembly. P A 12 04

21 SECTION III Adjustments Figure 3.7 F. REMOVE THE CLOSURE TRACK: Figure 3.7 Closures must slide freely through the closure track. Periodic inspections of the track assembly is recommended. Remove the closure track from the closer as follows: 1. Remove the two top covers from the closer. Note the screw lengths for reassembly. 2. Disconnect the breakoff spring from the spring anchor. 3. Locate and remove the two socket button head mounting screws securing the closure track to the closer frame. Note the two spacer bushings between the track assembly and the closer frame. 4. Gently work the closure track assembly out of the closer. 5. Inspect the track body for nicks or scratches. Light imperfections in the track can be sanded by hand to smooth them. Clean the track slot of any foreign material. 6. Lubricate the breakoff lever with a light mineral oil before remounting the track. 088A P 3.7

22 SECTION III Adjustments NOTE: To manually actuate the closer, the clutch must be tripped. To trip the clutch push the clutch actuator arm away from the clutch control collar. Turn the main drive pulley to cycle. The pulley rotates in one direction only, due to the clutch anti-backup feature. Figure Slide the closure track back into position on the closer. Align the bushings under the two mounting holes in the track. Be sure that the spring pin located in the front of the pick is positioned under the pick release plate. Tighten the closure track to the mainframe. 8. Reattach the breakoff return spring. 9. Replace the two top covers. G. BREAKOFF CAM POSITION: Figures 3.8 and 3.9 The breakoff cam is properly positioned when the pick connecting rod assembly is full forward in its stroke with the closer in neutral. Adjust as follows: 1. Disconnect the closer power cord. 2. Remove the two top covers. 3. Remove the closer bottom cover to expose the clutch and breakoff linkage. 4. With the clutch in neutral, Manually actuate the clutch. Turn the closer by hand through the closing cycle until the breakoff cam is in the position shown (Figure 3.9). Figure Slide the clutch control collar retaining ring upwards, followed by the control collar itself. 6. Rotate the control collar until it contacts the clutch actuator arm and then slide the collar back into position over the clutch splines. 7. Cycle the closer manually, check to see that the breakoff cam is in the proper position at the end of the closing cycle (neutral). If it is not, repeat step 4 above. 8. Return the retaining ring to its operating position and remount the three covers. P A 12 04

23 SECTION III Adjustments A - Stop Point B - Solenoid Plunger C - Actuating Lever D - Solenoid Coil E - Clutch Stop F - Plunger Press Point G - Solenoid Mounting Screws H - Control Collar Press Point I - Actuating Lever Pivot Figure 3.10 H. CLUTCH SOLENOID ADJUSTMENT: Figure 3.10 and 3.11 For proper clutch actuation, the clutch solenoid must be set correctly. Check and adjust as follows. 1. Check the clutch actuation. a. Rotate the clutch until the clutch stop (E) contacts the actuating lever (C). b. Manually trip the actuating lever to release the clutch stop. c. Rotate the clutch until the clutch stop is under the edge of the actuating lever (Figure 5.18) d. Press on the clutch control collar at point (H), pressing the collar toward the solenoid coil (D). e. Press down on the end of the solenoid plunger (F) pressing it into the solenoid as far as possible. Figure 3.11 f. Proper clearance between the actuating lever and the clutch stop must be between.010" -.030" as shown in Figure To adjust the clutch actuating lever. a. Loosen the two solenoid mounting screws (G) located on the back of the clutch mounting plate. b. Pivot the solenoid assembly so the end of the solenoid plunger is as far away from the actuating lever as possible. Figure c. Press the control collar at point (H) to minimize the distance between the clutch stop and the clutch solenoid. d. Press on the end of the solenoid plunger and fully insert it into the solenoid. e. Move the solenoid until the proper gap exists between the clutch stop and the actuating lever. Tighten the solenoid mounting screws and again check the clearance. 088A P 3.9

24 SECTION III Adjustments When properly adjusted, the closure jaw should be centered between the drive and idle pulleys. Closure direction Closure track Incoming package Closure in closing position Bag film guide Figure 3.12 I. BREAKOFF ARM ADJUSTMENT: Figure 3.9 With the closer in neutral and the breakoff arm properly adjusted, there should be a slight gap of approximately (0.4 mm) between the breakoff bearing and the breakoff cam. Adjust as follows: 1. Check to see that the closer is in neutral. 2. Remove the left top cover. 3. Loosen the cam bearing adjustment screws and rotate the breakoff cam bearing toward or away from the breakoff cam until the desired gap is achieved. 4. Tighten the two screws, and replace the cover. J. CLOSURE POSITION: Figure 3.12 The lok pick is properly adjusted when it positions the closure as indicated in Figure 3.12 with the closer in neutral. Be sure that the closer is in neutral, the lower idle and drivebelts are mounted and properly tensioned, and the closure track is mounted and tight before making the following adjustments: 1. Remove the upper idle belt assembly to access the end of the closure track and the bag film guide. 2. Cycle a strip of closures through the closure track until the end closure is in the closing position (Figure 3.15). P A 10 10

25 SECTION III Adjustments Figure Loosen the pick connecting rod locking nuts and rotate the connecting rod in the desired direction. Rotating the connecting rod changes the position of the pick, and so the position of the strip in the closure track. If the pick is moved backward, tug on the closure strip where it enters the track to seat the closure against the pick. Continue to adjust until the end closure of the strip is in the closing position shown (Figure 3.12). The jaw of the closure should be centered between the lower pulley assemblies. 4. Cycle the closer several times, checking the closure position. When satisfied, retighten the connecting rod locking nuts. Be sure that after tightening the rod ends pivot freely and have not been placed in a bind. K. PICK POSITION: Figures Figure 3.15 The lok pick should engage the closure strip near the back web of the closure, but not so close to that web as to let the pick slide over the web. Adjust as follows: 1. Lubricate and adjust the pick so that it moves freely without excessive play on the pick bearing. Figure Loosen the two set collars located on the pick shaft. 3. Slide the pick shaft assembly accordingly Figure 3.13). 4. Tighten the set collars, insuring that there is no side to side play in the pick arm shaft when tight. 088A P 3.11

26 SECTION III Adjustments M. BAG FILM GUIDE: Figures The bag film guide provides two functions. First, when properly set it protects the bag film from contacting the edge of the closure opening. Figure 3.16 Second, the film guide cams open the closure jaw which assists the feeding of the bag film into the closure. The correct film guide position is indicated in Figure Adjust as follows: 1. Insure that the closer is in neutral. 2. Remove the top idle belt assembly as detailed in Part A, Replace or Adjust the Upper Idle Belt. L. LOK CHECK: Figure 3.14 Figure 3.17 The lok check is adjusted correctly when it keeps the closure from backing up in the closure track as the pick moves through its back stroke. Adjust as follows: NOTE: The closures may back up slightly until contact is made with the lok check. 1. Be sure that the closer is in neutral. 2. Loosen the lok check mount and slide the check assembly in the desired direction. The leading edge of the check should align with the back edge of the closure slot. 3. Loosen the two bag film guide mounting screws. Position the bag film guide with a gap of 1/8-5/32 ( mm) as shown in Figures 3.12 and 3.15 and retighten the mounting screws. 4. Lightly push the end closure toward the front of the closer. Check the clearance between the front edge of the closure and the inside edge of the bag film guide. Set the clearance to.015 (0.4 mm). Move the film guide forward or backward to make this adjustment. 5. Check the Closure Cam dimension. This is preset by design but can be incorrect if the bag film guide has been bent. Re-bend the part until the desired cam is achieved. It is recommended the closure cam be set to (0.8 mm) maximum (Figures 3.16 and 3.17). 6. Replace the top idle belt assembly and be sure it pivots freely under the tensioner spring pressure. 3. Tighten the lok check mount and cycle the closer several times to verify the new setting for the check position. P A 09 10

27 SECTION III Adjustments N. ACTUATING LEVER SWITCH: Figure 3.18 The bag actuating lever switch signals the solenoid module to actuate the clutch. The actuating lever switch is normally closed. As the actuating lever rotates into the switch, the switch contacts open. As the actuating lever rotates out of the switch, the switch contacts close and sends a signal to the solenoid module to actuate the clutch. Adjust as follows: Disconnect power from the bag closer before proceeding. 1. Remove the two top covers from the closer. 2. Remove the top drive pulley section from the closer as detailed in part B, Replace or Adjust the Upper Drivebelt, located in this section of the manual. Figure Remove the small shield from the front of the closer. 4. Remove the lower cover to expose the solenoid module. 5. Disconnect the two wire leads from connectors 3 and 4 of the solenoid module. Connect a continuity meter to the two wire leads. 088A P 3.13

28 SECTION III Adjustments BAG TYPE UPPER PULLEY LOWER PULLEY SLOT POSITION SLOT POSITION Thin or fragile centered centered poly film Typical poly centered full downstream film Knit or woven full downstream full downstream mesh Figure When properly adjusted, the continuity meter signals the closing of the switch as the actuating lever pivots out of the switch. The actuating lever should open the switch with the actuating lever 1/4 (6.4 mm)or less from the actuating lever stop. The switch should close when the actuator lever is 1/8 (3.2 mm) or more from the actuating lever stop as indicated in Figure Slightly loosen the switch mounting screws (2). Move the switch assembly toward or away from the rotation of the actuating lever to adjust for the open and closed positions for the switch as indicated in number six above. 8. Reconnect the two wire leads to the solenoid module and replace the covers and shield before connecting the closer to electrical power. O. PULLEY POSITIONS: Figures 3.4 and 3.19 The location of the down-stream pulleys where the bag exits the belts affects how well the bag top is gathered into the closure opening. The standard location is with the upper pulleys midway in the mounting slots and the lower pulleys in the extreme down-stream position of the slots. As a general rule, to gather the bag more completely into the closure opening, move the pulleys down-stream. To reduce bag marking or tearing, move the pulleys upstream. The following chart may be used as a guide. Refer to Adjustments, Parts A thru D above for moving the pulleys. To reposition the pulleys, you must have access to both sides of the belt assembly. When relocating the pulleys: 1. First position the down-stream, idle side pulley. 2. Tension the belt by moving the corresponding up-stream pulley. 3. Align the two drive-side pulleys to the idle-side pulleys while the belt is slack. 4. Move the tensioner pulley to tighten the drive belt. NOTE: The procedure is the same for upper and lower pulleys. P A 09 10

29 SECTION IV Trouble Shooting Machine does not run when switch is turned on. Closer does not cycle Closure does not advance 088A PROBLEM No supply power Overheated motor Actuating lever switch out of adjustment Actuating lever not returning Actuating switch defective Clutch drivebelt damaged/broken Electrical solenoid module defective Clutch solenoid incorrectly adjusted or dirty Clutch solenoid defective Clutch defective CAUSE Electrical wires disconnected or damaged Lok check not engaged or incorrectly adjusted Closure jammed in lok track Closures jammed against breakoff lever Closures jammed against bag film guide Pick out of position Make sure power cord is connected to an active electrical source of the correct voltage. Internal protection turns motor off when overloaded. Allow motor to cool, and it will automatically reset. Adjust per SECTION III, Part N. Inspect the actuating switch lever and spring for damage or debris. Replace actuating switch. Replace and adjust per SECTION III, Part E. Replace solenoid module. Clean and adjust solenoid per SECTION III, Part H. Replace clutch solenoid. Replace clutch. CORRECTION Connect/replace damaged wires. Adjust lok check per SECTION III, Part L. Inspect and clear jammed loks. Adjust breakoff cam per SEC- TION III, Part G. Inspect breakoff arm spring, breakoff arm, link and lok breaker for damage or binding. Adjust film guide per SECTION III, Part M. Adjust pick position per SECTION III, Part K. P 4.1

30 SECTION IV Trouble Shooting PROBLEM Closure does not break off Bag is not completely fed into the closure opening Cut in closure area of bag CAUSE Closure fed incorrectly into lok track Lok breaker incorrectly adjusted or damaged Closures slipping out of the lok track Incorrect feed belt pulley position Bag too wide or too thick for closure opening Closures slipping out of the lok track Upper or lower feed drive belt loose Worn or damaged feed belts Upper or lower idle belt pivot plate out of position Feed belt pinch point incorrect Poor bag presentation Closure not cammed open by film guide Closure improperly positioned CORRECTION Review SECTION II, Part D through Part F. Adjust breakoff cam per SEC- TION III, Part G. Inspect breakoff arm, link and lok breaker for damage or binding. Make sure anti-backup spring is in lok track. Use guide shim when running closures. Adjust per SECTION III, Part O. Use closure with larger opening. Contact Kwik Lok for the proper opening size. Make sure anti-backup spring is in lok track. Use guide shim when running closures. Adjust per SECTION III, Part B and Part D. Inspect upper and lower feed belts. Replace or adjust as needed per SECTION III, Parts A through D. Inspect and adjust per SECTION III, Part A and Part C. Adjust per SECTION III, Part B and Part D. Operator must present bag per SECTION II, Part I. Adjust film guide per SECTION III, Part M. Adjust pick per SECTION III, Part J. P A 10 10

31 SECTION IV Trouble Shooting PROBLEM Excessive damage to bag CAUSE Poor bag presentation Bag closed too tight Bag forced too deep into closure opening CORRECTION Operator must present bag per SECTION II, Part I. Increase distance between bottom of closer and product. Adjust feed belt pulley position per SECTION III, Part O. 088A P 4.3

32

33 The closer is a RIGHT or LEFT- HAND model. Parts lists include part numbers for both Right and Left-Hand models when applicable. Part numbers followed by an R are specific to a Right- Hand closer. Numbers followed by an L are specific to a Left-Hand closer. SECTION V Parts Identification IMPORTANT: When ordering parts ALWAYS: PARTS ORDERING PROCEDURES (1) Specify on the order the TYPE, MODEL and SERIAL NUMBER of the machine for which the parts are being ordered. This information is found on the machine's nameplate. (2) Do NOT order by item number. Order by part number. To order individual PARTS, be sure to observe the following procedure: A. Identify the desired PART(S) by referring to the assembly illustrations following in this section. Each PART is assigned an "Item Number" on this illustration. DO NOT ORDER BY THE ITEM NUMBER. B. Refer to the drawings parts list. Locate the pertinent item number in the left-hand column. Opposite the item number is the part number and description to be listed on the order. As an example Shield - Small (see pages 5.2 & 5.3) identifies the Shield as item 16 on the drawing. Referring to the PARTS COMMON Parts List, the description for Item Number 16 is "Part Shield - Small" If the machine nameplate is marked "Type 088A, Model A Serial ," the order should specify as follows: "One Part Shield -Small " (For Closing Head Type 088A, Model A, Serial ) IMPORTANT: The 088A A closure is available in Right - Hand or Left - Hand models. ALL ILLUSTRATIONS DEPICTED IN THIS MANUAL ARE CONFIGURED TO A RIGHT - HAND MODEL 088A A. Parts lists include part numbers for both Right and Left-Hand models when applicable. Part Numbers followed by an R are specific to a Right-Hand machine. Part Numbers followed by an L are specific to a Left-Hand machine. Determine the hand of the machine to insure that the correct parts are ordered. In rare cases it is possible for a Right-Hand part to be used on a Left-Hand machine or a Left-Hand part on a Right-Hand machine. If this is the case, the part description column of the parts list will indicate that this part is specifically for a Right or Left-Hand machine. Use the information and illustration offered below to establish if your machine is a Right or Left-Hand model. 1. MODEL- HAND box on the machine's Nameplate. For a Right Hand model the last letter will be "R". MANUFACTURED BY CORPORATION YAKIMA, WASHINGTON, U.S.A. 088A AK-NRPR For a Left Hand model the last letter will be "L". TYPE MODEL - HAND SERIAL NUMBER VAC, Hz, Amps, Ph 088A P 5.1

34 SECTION V Parts Identification 088A CLOSER PARTS COMMON Figure 5.1 P A 09 10

35 The closer is a RIGHT or LEFT- HAND model. Parts lists include part numbers for both Right and Left-Hand models when applicable. Part numbers followed by an R are specific to a Right- Hand closer. Numbers followed by an L are specific to a Left-Hand closer. SECTION V Parts Identification 088A PARTS COMMON (Figure 5.1) Item Part Description Frame - Main R Gusset - Frame L Gusset - Frame R Mount - Closer L Mount - Closer Plate - Upper Trim Plate - Upper Pivot Plate - Lower Fixed Plate - Lower Pivot Post - Pivot Plate - Filler Post - Plate Mount Post - Shield Mount R Guide - Bag Film L Guide - Bag Film Block - Guide Mount Base - Mast R Shield - Large L Shield - Large Shield - Small R Base - Stand L Base - Stand Mount - Inner Nose Guard R Mount - Nose Guard L Mount - Nose Guard Plug - Pressure Adjust S-018 Spring W-001 S Washer W-002 S Washer 1 24 P Foot - Leveling 4 25 P Plug - Plastic 2 PARTS LIST Qty. Item Part Description Qty. 26 P Knob 1 27 P Knob 1 28 P Pin 2 29 P Nut ESNA 4 30 P Nut - 1/4-20UNC - Acorn 4 31 P Washer - Nylon F03-190F S Nut UNF - Hex 1 33 F03-250C Nut - 1/4-20UNC - Hex 4 34 F06-190C04 S Screw UNC x 1/4 Lg Skt Set 2 35 F06-375C16 S Screw - 3/8-16UNC x 1 Lg Skt Set 1 36 F10-190F10 S Screw UNF x 5/8 Lg Skt Hd Cap 4 37 F10-190F12 S Screw UNF x 3/4 Lg Skt Hd Cap 2 38 F10-250C12 Screw - 1/4-20UNC x 3/4 Lg Skt Hd Cap 1 39 F11-190F04 S Screw UNF x 1/4 Lg Skt Btn Hd 2 40 F11-190F06 S Screw UNF x 3/8 Lg Skt Btn Hd F11-190F10 S Screw UNF x 5/8 Lg Skt Btn Hd 5 42 F11-190F14 S Screw UNF x 7/8 Lg Skt Btn Hd 2 43 F11-190F20 S Screw UNF x 1 1/4 Lg Skt Btn Hd 1 44 F12-190F10 S Screw UNF x 5/8 Lg Skt Flt Hd Collar - Closer Safety 1 088A P 5.3

36 SECTION V Parts Identification 088A DRIVE SYSTEM Figure 5.2 P A 03 10

37 The closer is a RIGHT or LEFT- HAND model. Parts lists include part numbers for both Right and Left-Hand models when applicable. Part numbers followed by an R are specific to a Right- Hand closer. Numbers followed by an L are specific to a Left-Hand closer. SECTION V Parts Identification 088A DRIVE SYSTEM (Figure 5.2) Item Part Description Plate - Clutch Mount Post - Clutch Mount Post - Clutch Angle Shaft - Breakoff Cam Bushing - Adjust Pulley - Long Pulley - Main Drive Pulley - Clutch Drive Plate - Motor Mount Pulley - Clutch 1 10 Z Kit - Pulley - Idle - Flat 1 consists of: Pulley - Half 1 P Bearing 1 P Screw S-062 Spring W-001SP Washer 1 13 BS Bushing 1 PARTS LIST Qty. Item Part Description Qty. 14 BS Bushing 2 15 BS Bushing 1 16 P Bearing 2 17 P Belt - Drive 1 18 P R Clutch 1 P L Clutch 1 19 F S Washer - No 10 Flt 1 20 F04-250F Nut - 1/4-28UNF - Hex 3 21 F10-138C06 S Screw UNC x 3/8 Lg Skt Hd Cap 3 22 F10-190F28 S Screw UNF x 1 3/4 Lg Skt Hd Cap 3 23 F10-250C22 S Screw - 1/4-20UNC x 1 3/8 Lg Skt Hd Cap 3 24 F11-190F06 S Screw UNF x 3/8 Lg Skt Btn Hd 4 25 F11-190F08 S Screw UNF x 1/2 Lg Skt Btn Hd 2 26 F13-250F36 Screw - 1/4-28UNF x 2 1/4 Lg Hx Hd 4 088A P 5.5

38 SECTION V Parts Identification 088A LOK TRACK Figure 5.3 P A 03 10

39 The closer is a RIGHT or LEFT- HAND model. Parts lists include part numbers for both Right and Left-Hand models when applicable. Part numbers followed by an R are specific to a Right- Hand closer. Numbers followed by an L are specific to a Left-Hand closer. SECTION V Parts Identification Item Part Description R Mount - Lok Check L Mount - Lok Check Arm - Breakoff Link - Breakoff R Guide - J-NRP or K-NRP Track L Guide - J-NRP or K-NRP Track R Guide - JM-NRP or KM-NRP Track L Guide - JM-NRP or KM-NRP Track R Spacer - Track L Spacer - Track R Shim - Closure Guide L Shim - Closure Guide R Shim - Closure Guide Model APR Only L Shim - Closure Guide Model APR Only Spring - Anti Backup Spring - Shim Locking Spring - Pick Release Pivot - Lok Check Washer - Lok Check Check - Lok Nut - Pulley Spacer - Bearing Plate - Cam Bearing Adjust Mount - Breakoff Link R Breaker - Lok - J-NRP or K-NRP L Breaker - Lok - J-NRP or K-NRP R Breaker - Lok - JM-NRP or KM-NRP L Breaker - Lok - JM-NRP or KM-NRP W-001SP Washer S-006 S Spring 1 088A LOK TRACK (Figure 5.3) PARTS LIST Qty. Item Part Description Qty. 20 0S-079 Spring 1 21 P Bearing 1 22 P Knob - 1/2 x 3/4 Lg 1 23 P S Nut UNC - ESNA 1 24 P S Nut UNF ESNA Low Profile 1 25 P Washer - Nylon 2 26 BS Bushing 2 27 BS Bushing 1 28 P Nut UNC - ESNA 2 29 F S Washer Lock 1 30 F03-138C S Nut UNC Hex 2 31 F03-164C S NUT UNC - Hex 1 32 F03-190F S Nut UNF - Hex 1 33 F07-138C10 S Screw UNC x 5/8 Lg Mach Hd 1 34 F10-190F16 S Screw UNF x 1 Lg Skt Hd Cap 1 35 F11-138C04 S Screw UNC x 1/4 Lg Skt Btn Hd 1 36 F11-164C12 S Screw UNC x 3/4 Lg Skt Btn Hd 1 37 F11-190F04 S Screw UNF x 1/4 Lg Skt Btn Hd 6 38 F11-190F05 S Screw UNF x 5/16 Lg Skt Btn Hd 1 39 F11-190F06 S Screw UNF x 3/8 Lg Skt Btn Hd 3 40 F11-190F12 S Screw UNF x 3/4 Lg Skt Btn Hd 3 41 F12-112C04 S Screw UNC x 1/4 Lg Skt Flt Hd 2 42 F12-190F04 S Screw UNF x 1/4 Lg Skt Flt Hd 4 43 F12-190F05 S Screw UNF x 5/16Lg Skt Flt Hd 1 44 F12-190F07 S Screw UNF x 7/16 Lg Skt Flt Hd 1 088A P 5.7

40 SECTION V Parts Identification UPPER BELTS Figure 5.4 P A 09 10

41 The closer is a RIGHT or LEFT- HAND model. Parts lists include part numbers for both Right and Left-Hand models when applicable. Part numbers followed by an R are specific to a Right- Hand closer. Numbers followed by an L are specific to a Left-Hand closer. SECTION V Parts Identification UPPER BELTS (Figure 5.4) Item Part Description Bushing - Pulley Bushing - Adjustment Pulley 1 3 Z Kit - Pulley - Idle - Gear 3 consists of: Pulley - Half 2 P Bearing 1 P Screw 4 4 Z Kit - Pulley - Idle - Flat 2 consists of: Pulley - Half 2 P Bearing 1 P Screw 4 5 0W-001SP Washer 1 PARTS LIST Qty. Item Part Description Qty. 6 P Belt Gear Belt - Upper - Idle 1 8 P Nut UNF - Esna 1 9 F03-190F S Nut UNF - Hex 4 10 F11-190F04 S Screw UNF x 1/4 Lg Skt Btn Hd 1 11 F11-190F05 S Screw UNF x 5/16 Lg Skt Btn Hd 1 12 F11-190F16 S Screw UNF x 1 Lg Skt Btn Hd 1 13 F11-190F11 S Screw UNF x 11/16 Lg Skt Btn Hd 4 088A P 5.9

42 SECTION V Parts Identification LOWER BELTS Figure 5.5 P A 03 10

43 The closer is a RIGHT or LEFT- HAND model. Parts lists include part numbers for both Right and Left-Hand models when applicable. Part numbers followed by an R are specific to a Right- Hand closer. Numbers followed by an L are specific to a Left-Hand closer. SECTION V Parts Identification LOWER BELTS (Figure 5.5) Item Part Description Bushing - Pulley Bushing - Adjust Pulley 1 3 Z Kit - Pulley - Idle - Gear 3 consists of: Pulley - Half 2 P Bearing 1 P Screw 4 4 Z Kit - Pulley - Idle - Flat 2 consists of: Pulley - Half 2 P Bearing 1 P Screw 4 PARTS LIST Qty. Item Part Description Qty. 5 0W-001SP Washer 2 6 P Belt - Gear Belt - Lower Idle 1 8 F03-190F S Nut UNF - Hex 4 9 F11-190F04 S Screw UNF x 1/4 Lg Skt Btn Hd 1 10 F11-190F05 S Screw UNF x 5/16 Lg Skt Btn Hd 1 11 F11-190F11 S Screw UNF x 11/16 Lg Skt Btn Hd 4 12 F S Washer - No 10 Flat 4 088A P 5.11

44 SECTION V Parts Identification PICK ASSEMBLY Figure 5.6 P A 03 10

45 The closer is a RIGHT or LEFT- HAND model. Parts lists include part numbers for both Right and Left-Hand models when applicable. Part numbers followed by an R are specific to a Right- Hand closer. Numbers followed by an L are specific to a Left-Hand closer. SECTION V Parts Identification PICK ASSEMBLY (Figure 5.6) Item Part Description Rod - Pick Connecting Mount - Pick Shaft Pick - Lok Bearing - Pick Arm - Pick L Shaft - Pick (For Right-Hand machine) R Shaft - Pick (For Left-Hand machine) 1 7 0W-001SP Washer 2 8 BS Bushing 2 9 0S-035 Spring S-043 Spring S-054 Spring 1 12 P Bearing 2 13 P S Nut UNF - ESNA 2 14 P Pin - Spring - 1/8 x 1/2 Lg 1 15 P S Nut UNF - ESNA 2 PARTS LIST Qty. Item Part Description Qty. 16 P Rod End -Right-Hand Thread 1 17 P Rod End - Left-Hand Thread 1 18 P Collar - Set 2 19 P Washer - Nylon 2 20 F03-190F SL Nut UNF - Left-Hand Hex 1 21 F10-190F03 S Screw UNF x 3/16 Lg Skt Hd Cap 1 22 F10-190F10 S Screw UNF x 5/8 Lg Skt Hd Cap 3 23 F10-190F12 S Screw UNF x 3/4 Lg Skt Btn Hd 1 24 F10-190F18 S Screw UNF x 1 1/8 Lg Skt Hd Cap 4 25 F10-190F07 S Screw UNF x 7/16 Lg Skt Hd Cap 3 26 F03-190F S Nut UNF - Hex 4 088A P 5.13

46 SECTION V Parts Identification ELECTRICAL HARDWARE Figure 5.7 P A 03 10

47 The closer is a RIGHT or LEFT- HAND model. Parts lists include part numbers for both Right and Left-Hand models when applicable. Part numbers followed by an R are specific to a Right- Hand closer. Numbers followed by an L are specific to a Left-Hand closer. SECTION V Parts Identification ELECTRICAL HARDWARE (Figure 5.7) Item Part Description Lever - Actuator Mount - Actuating Lever R Mount - Sensor L Mount - Sensor R Mount - Switch L Mount - Switch Mount - Breakoff Link Jumper 2 or Shield - Pushbutton 1 8 0S-012 Spring 1 9 P Solenoid - Clutch Actuating 1 10 P Module - Solenoid 1 11 P Cord and 115VAC 1 P Cord - 230VAC 1 P Cord - 230VAC - International 72 P Plug - Two Pole Tandem With Ground - 230VAC 1 12 P Terminal - Closed Loop 1 13 P Terminal - Quick Connect 2 14 P Terminal - Quick Connect P Terminal 4 16 P Clamp - Cord 1 17 P Nut - Wire 2 18 P Strain Relief 1 19 P Sensor - Magnetic 1 20 P Switch - Manual Cycle 1 21 P Switch - Rocker Low Voltage 1 P Switch - Rocker High Voltage 1 PARTS LIST Qty. Item Part Description Qty. 22 P Motor - 115VAC 1 P Motor - 100VAC 1 P Motor - 230VAC 1 23 P Capacitor - 115VAC - 9uf 1 P Capacitor - 100VAC- 11uf 1 P Capacitor - 230VAC - 2.3uf 1 24 P Gearhead - Motor 1 25 P Nut UNC x ESNA 1 26 F03-190F S Nut UNF - hex 1 27 F07-138C06 S Screw UNC x 3/8 Lg Mach Hd 1 28 F10-190F04 S Screw UNF x 1/4 Lg Skt Btn Hd 1 29 F10-190F32 S Screw UNF x 2 Lg Skt Hd Cap 2 30 F11-190F04 S Screw UNF x 1/4 Lg Skt Btn Hd 2 31 F11-164C06 S Screw UNC x 3/8 Lg Skt Btn Hd 1 32 F11-190F14 S Screw UNF x 7/8 Lg Skt Hd Cap 2 33 F12-112C06 S Screw UNC x 3/8 Lg Skt Flt Hd 1 34 F10-190F16 S Screw UNF x 1 Lg Skt Hd Cap 1 35 P Terminal - Piggyback 2 088A P 5.15

48 SECTION V Parts Identification COVERS Figure 5.8 P A 09 10

49 The closer is a RIGHT or LEFT- HAND model. Parts lists include part numbers for both Right and Left-Hand models when applicable. Part numbers followed by an R are specific to a Right- Hand closer. Numbers followed by an L are specific to a Left-Hand closer. SECTION V Parts Identification COVERS (Figure 5.8) PARTS LIST ITEM PART NO. NUMBER DESCRIPTION QTY POST - COVER R COVER - BOTTOM L COVER - BOTTOM R COVER - TOP DRIVE L COVER - TOP DRIVE R COVER - TOP CAM L COVER - TOP CAM R GUARD - INNER NOSE L GUARD - INNER NOSE R GUARD - OUTER NOSE L GUARD - OUTER NOSE 1 7 P PLUG - PLASTIC 1 8 F11-190F05 S SCREW UNF X 5/16 LG SKT BTN HD 8 9 F11-190F06 SCREW UNF x 3/8 LGSKT BTN HD 2 10 F11-190F06 S SCREW UNF X 3/8 LG SKT BTN HD F11-190F08 S SCREW UNF X 1/2 LG SKT BTN HD 2 12 F11-190F14 S SCREW UNF X 7/8 LG SKT BTN HD 1 13 F12-190F08 S SCREW UNF X 1/2 LG SKT FLT HD 1 088A P 5.17

50 SECTION V Parts Identification Z KIT - J/K REEL (MODEL AR - NO PRINTER) Z KIT - JM/KM REEL (MODEL AR - NO PRINTER) Figure 5.9 P A 10 10

51 The closer is a RIGHT or LEFT- HAND model. Parts lists include part numbers for both Right and Left-Hand models when applicable. Part numbers followed by an R are specific to a Right- Hand closer. Numbers followed by an L are specific to a Left-Hand closer. SECTION V Parts Identification Z KIT - J/K REEL (MODEL AR - NO PRINTER) Z KIT - JM/KM REEL (MODEL AR - NO PRINTER) (Figure 5.9) Item Part PARTS LIST Description Qty. Item Part Description Qty Mast Shaft - Lok Roller Knob - Reel Pin - Reel Plate Detent Hub - Reel Bearing - J or K Hub - Reel Bearing - JM or KM Bearing - Reel Hub - J or K Bearing - Reel - JM or KM Plate - Reel Front Plate - Reel Rear Spacer - Closer Reel Roller - Lok Guide W-002 S Washer 1 12 P Plunger - Spring 1 13 P Plunger - Spring 1 14 F10-19C06 S Screw UNC x 3/8 Lg Skt Hd Cap 3 15 F10-190C14 S Screw UNC xc 7/8 Lg Skt Hd Cap 3 16 F10-250C20 Screw - 1/4-20UNC x 1 1/4 Skt Hd Cap 2 17 F11-250F08 Screw - 1/4-28UNF x 1/ P Pin - Drive 1 088A P 5.19

52 SECTION V Parts Identification Z KIT - J/K REEL (MODEL APR WITH PRINTER) Z KIT - JM/KM REEL (MODEL APR WITH PRINTER) Figure 5.10 P A 03 10

53 The closer is a RIGHT or LEFT- HAND model. Parts lists include part numbers for both Right and Left-Hand models when applicable. Part numbers followed by an R are specific to a Right- Hand closer. Numbers followed by an L are specific to a Left-Hand closer. SECTION V Parts Identification Z KIT - J/K REEL (MODEL APR WITH PRINTER) Z KIT - JM/KM REEL (MODEL APR WITH PRINTER) (Figure 5.10) Item Part PARTS LIST Description Qty. Item Part Description Qty Mast Arm - Reel Roller Plate - Roller Arm Mount Shaft - Roller Mount Knob - Reel Pin - Reel Plate Detent Hub - Reel Bearing - J or K Hub - Reel Bearing - JM or KM Bearing- Reel Hub - J or K Bearing - Reel Hub - JM or KM Plate - Reel - Front Plate - Reel - Rear Spacer - Closure Reel Roller - Lok Guide W-002 S Washer 1 14 P Plunger 1 15 P Plunger - Spring - Stubby 1 16 P S Nut UNF - ESNA 1 17 F10-190F18 S Screw UNF x 1 1/8 Lg Skt Hd Cap 1 18 F10-190C06 S Screw UNC x 3/8 Lg Skt Hd Cap 3 19 F10-190C14 S Screw UNC x 7/8 Lg Skt Hd Cap 3 20 F10-250C20 Screw - 1/4-20UNC x 1 1/4 Lg Skt Hd Cap 2 21 F11-190F06 S Screw UNF x 3/8 Lg Skt Btn Hd 4 22 F11-250F08 Screw - 1/4-28UNF x 1/2 Lg Skt Btn Hd 1 23 P Pin Drive 1 088A P 5.21

54 SECTION V Parts Identification Z KIT-CFJ LABEL REEL (MODEL AR-NO PRINTER) Z KIT-PF/TF LABEL REEL (MODEL AR-NO PRINTER) Z KIT-PFM/TFM LABE REEL (MODEL AR-NO PRINTER) Figure 5.11 P A 03 10

55 The closer is a RIGHT or LEFT- HAND model. Parts lists include part numbers for both Right and Left-Hand models when applicable. Part numbers followed by an R are specific to a Right- Hand closer. Numbers followed by an L are specific to a Left-Hand closer. SECTION V Parts Identification Z KIT-CFJ LABEL REEL (MODEL AR-NO PRINTER) Z KIT-PF/TF LABEL REEL (MODEL AR-NO PRINTER) Z KIT-PFM/TFM LABEL REEL (MODEL AR-NO PRINTER) (Figure 5.11) PARTS LIST Item Part Description Qty Mast Disk - Reel Brake Shaft - Reel Latch Bearing Bushing - Reel Bearing Spacer - CJ, PF, or TF Label Reel Roller - Lok Guide Roller - Center Shaft - Lok/Label Roller Hub - Latch Mounting Axle - PF or TF Label Reel Axle - CJ Label Reel 1 11 * Reel Assembly - PF or TF Label 1 * Reel Assembly - CJ Label 1 * Reel assembly - PFM and TFM Label W-002 S Washer 1 13 P Bearing 1 14 P Ring - Retaining 1 15 F10-250C20 Screw - 1/4-20UNC x 1 1/4 Skt Hd Cap 2 16 F11-250F08 Screw - 1/4-28UNF x 1/2 Skt Btn Hd 1 17 P Pin - Drive 1 *Three latches are included with items , and Reel Assemblies. The latches can be ordered separately as P Latch. 088A P 5.23

56 SECTION V Parts Identification LABEL REELS Z KIT-CFJ REEL (MODEL APR WITH PRINTER) Z KIT-PF AND TF REEL (MODEL APR WITH PRINTER) Z KIT PFM/TFM REEL (MODEL APR WITH PRINTER) P 5.24 Figure A 03 10

57 The closer is a RIGHT or LEFT- HAND model. Parts lists include part numbers for both Right and Left-Hand models when applicable. Part numbers followed by an R are specific to a Right- Hand closer. Numbers followed by an L are specific to a Left-Hand closer. SECTION V Parts Identification LABEL REELS Z KIT-CFJ REEL (MODEL APR WITH PRINTER) Z KIT-PF AND TF REEL (MODEL APR WITH PRINTER) Z KIT PFM/TFM REEL (MODEL APR WITH PRINTER) (Figure 5.12) Item Part PARTS LIST Description Qty. Item Part Description Qty Mast Arm - Reel Roller Plate - Roller Arm Mount Disk - Reel Brake Axle - Label Reel P or T Labels Axle - Label Reel - CJ Label Shaft - Label Latch Bearing Bushing - Reel Bearing Spacer - Label Reel Roller - Lok Guide Roller - Center - Lok Guide Shaft - Lok Label Roller Hub - Latch Bearing 1 13 * Reel - P and T Label 1 * Reel - CJ Label 1 * Reel Assembly - PFM and TFM Label W-002 S Washer 1 15 P Bearing 1 16 P S Nut UNF - ESNA 1 17 P Ring - Retaining - Internal 1 18 F10-190F18 S Screw UNF x 1 1/8 Lg Skt Hd Cap 1 19 F10-250C20 Screw - 1/4-20UNC x 1 1/4 Lg Skt Hd Cap 2 20 F11-190F06 S Screw UNF x 3/8 Lg Skt Btn Hd 4 21 F11-250F08 Screw - 1/4-28UNF x 1/2 Lg Skt Btn Hd 1 * P Latch 1 22 P Pin - Drive 1 *Three latches are included with items , and Reel Assemblies. The latches can be ordered separately as P Latch. 088A P 5.25

58 SECTION V Parts Identification LONG BAG GUIDES - OPTIONAL Item Part Figure 5.13 PARTS LIST Description Qty R Guide - Bag L Guide Bag 1 3 P Washer - Nylon 24 4 F11-190F10 S Screw UNF x 5/8 Lg Skt Btn Hd 4 P A 09 10

59 SECTION VI Wiring Diagrams 088A WIRING DIAGRAM - 115VAC, 230VAC LINE IN SEE NOTE 1 SEE NOTE 2 SEE NOTE 3 NOTE: ALL WIRE 18 GA UNLESS NOTED. NOTE 1: NORTH AMERICA: WHITE INTERNATIONAL : BLUE ON OFF MAIN POWER SWITCH 5" SEE NOTE 1 RIGHT HAND MACHINE NOTE 2: NORTH AMERICA: BLACK INTERNATIONAL : BROWN NOTE 3: NORTH AMERICA: GREEN INTERNATIONAL : GREEN WITH YELLOW TR 5" SEE NOTE 2 WHITE 5-1/2" BLACK WHITE RED MOTOR ccw AC INPUT CLUTCH SOLENOID 24VDC BLACK 11-1/2" BLACK 11-1/2" 1 2 SOLENOID MODULE VAC VAC VAC 5 6 JUMPER AS SHOWN TO MATCH AC INPUT VOLTAGE CAPACITOR CAP LEFT HAND MACHINE 20 GA VIOLET 9" PUSH BUTTON WITH LIGHT 20 GA VIOLET 9" BLACK 9" BLACK 3-1/2" WIRE NUT (TAPE) BLACK 20 GA BLACK WHITE 6-1/2" BLACK WHITE RED MOTOR cw BLACK 9" WIRE NUT (TAPE) BLACK MAGNETIC SENSOR CAP CAPACITOR CHANGE FOR LEFT-HAND Figure A P 6.1

60

61 Appendix BAG LENGTH FORMULAS TO DETERMINE THE PROPER BAG LENGTH FOR A LOOSE BULK PRODUCT (E.G. Oranges, potatoes, sugar, ice, macaroni, etc.) FOLLOW THIS PROCE- DURE: 1. Fill the bag to the desired weight using samples of the product to be closed. 2. Close bag with the proper Striplok closure. 3. Check the length of the bag above the closure. The proper bag length allows 4 of the bag above the closure (not including the lip of the bag). * Normal variations in size and density of products will occur. Oranges, grapefruit and potatoes dehydrate as the season progresses; bakery products vary due to over proofing; and the density of ice changes because of certain manufacturing techniques. Therefore, the above bag length formulas take into account these variations to give maximum bag closing dependability. TO DETERMINE THE PROPER BAG LENGTH * FOR A CONSISTENTLY SHAPED PRODUCT (E.G. Bread, bun clusters, trays, english muffins, etc.) FOLLOW THIS FORMULA: TOTAL BAG LENGTH EQUALS THE LENGTH OF THE PRODUCT PLUS 1/2 OF THE DIAGONAL OF THE PRODUCT END PLUS 4 INCHES. 088A A

62 Appendix Upper trim plate OPTIONAL BAG NECK TRIMMER 088 Trimmer The optional bag neck trimmer trims poly and net bag necks leaving 1.75 (4.4 cm) above the closure. The trimmer is powered by the closer. The trimmer feed belts run at the same speed as the closer feed belts. The bag neck is trimmed as the closure is applied to the package. A 088 Trimmer feed belt slot 088 Closer feed belt slot Figure 1 Figure 2 (Covers removed) PREPARE THE CLOSER FOR THE TRIMMER: The 088 is available with an optional bag neck trimmer attachment. Field installation of the trimmer requires kit Z (right or left). The kit includes a new upper trim plate which must be installed on the closer. The trimmer also must be mounted to the closer using the first time mounting procedure shown below. Trimmers that were ordered from Kwik Lok with a new 088 closer do not need the new upper trim plate or the first time mounting procedure. Closers that were returned to Kwik Lok for rework to accept the trimmer also do not need the new trim plate or mount procedure. 1. Disconnect the 088 power cord from the electrical source. 2. Remove the upper trim plate (upper drive belt plate) by following the procedures in SECTION III,Part B. 3. Remove the belt tension pulley from the old upper trim plate and install on the new upper trim plate (Figure 3). 4. Remove the rear belt pulley from the old upper trim plate and install on the new upper trim plate. Install the pulley in the same location in the pulley slot. 5. Press the bearing into the bearing mount. The bearing must be flush to the end of the bearing mount as shown in Figure Install the bearing mount in the new upper trim plate. 7. Insert the driveshaft nut between the pulley halves and assemble using the included fasteners. B 088A 10 10

63 Appendix Grease the trimmer drive fastener Trimmer mounting brackets (2) New upper trim plate Bearing mount Bearing Drive shaft nut Install the rear belt pulley on the new upper trim plate Install the belt tension pulley on the new upper trim plate Figure 3 8. Install the pulley in the bearing mount in the new upper drive belt plate, as shown in Figure Install the new upper trim plate in the closer by following the procedures in SECTION III. Part B. Note that the front drive belt pulley is now fixed, and is not adjustable. B. MOUNT THE TRIMMER - FIRST TIME ONLY: The following procedure is only performed the first time the trimmer is mounted to the closer. It may need to be repeated if major work is performed to either the closer or the trimmer. 1. Disconnect the 088 closer power cord from the electrical source. 2. Install the two trimmer mount brackets on the new upper trim plate (upper drive belt plate). Do not tighten the screws. 3. Put some grease into the head of the trimmer drive fastener on the closer. 4. Place the trimmer into the trimmer mount brackets. Make sure the hex coupler drive pin fully engages into the drive fastener. Manually move the trimmer feed belts if needed to allow the drive to engage. 5. Align the trimmer feed belt slot with the closer feed belt slot. Tighten the screws to secure the trimmer mount brackets to the closer (Figure 1). Press the bearing flush with the end of the bearing mount 6. Make sure the trimmer is level. 7. Tighten the two locking knobs. Figure 4 088A C

64 Appendix Top plates Drive belt Cutter blade mounting screws (2) Cutter blade spacer Cutter blade Drive belt adjustment pulley Idle belt adjustment pulley Locking knobs (2) Front drive pulley Idle belt Gearbelt support mounting screw Front idle pulley Figure 5 C. REMOVE THE TRIMMER: 1. Loosen the two locking knobs that hold the trimmer to the mounting brackets. 2. Pull up on the trimmer to remove it from the 088 closer. D. INSTALL THE TRIMMER: 1. Disconnect the 088 closer power cord from the electrical source. 2. Put some grease into the head of the trimmer drive fastener. 3. Place the trimmer into the trimmer mount brackets. Make sure the hex coupler drive pin fully engages into the drive fastener. Manually move the trimmer feed belts, if needed, to allow the drive to engage. 4. Make sure the trimmer is level. 5. Tighten the two locking knobs. D 088A 09 10

65 Appendix E. REPLACE CUTTER BLADE: Figure 5 1. Disconnect the 088 closer power cord from the electrical source. 2. Loosen the two locking knobs that hold the trimmer to the mounting brackets. 3. Pull up on the trimmer to remove it from the 088 closer. 4. Remove the top plates. 5. Loosen the gearbelt support mounting screw and slide the gearbelt support away from the cutter blade. 6. Loosen the mounting screw on the drive belt adjustment pulley. Remove the drive belt from the adjustment pulley while leaving it wraped around the front drive pulley. Slide the adjustment pulley away from the blade. 7. Remove the cutter blade pulley mount screw. Remove the blade and pulley assembly from the machine. CAUTION: The cutter blade is very sharp. Use extreme caution when handling. 8. Remove the two cutter blade mounting screws. Separate the cutter blade from the pulley. 9. Install a new cutter blade on the pulley with the two mounting screws. Make sure the bevel on the blade is toward the pulley. 10. Install the blade and pulley assembly in the trimmer. Make sure the cutter blade spacer is positioned correctly. 11. Route the belt correctly, and then slide the drive belt adjustment pulley away from the cutter blade to tension the belt. Tighten the mounting screw. F 12. Slide the gearbelt support toward the cutter blade. The gearbelt support should be very close to the belt, but not make contact with the belt. Tighten the fastener. 13. Install the top plates. 14. Mount the trimmer on the 088 closer. Make sure the hex coupler drive pin fully engages into the drive fastener. Manually move the trimmer feed belts if needed to allow the drive to engage. REPLACE FEED BELT DRIVE SIDE: Figure 5 1. Disconnect the 088 closer power cord from the electrical source. 2. Loosen the two locking knobs that hold the trimmer to the mounting brackets. 3. Pull up on the trimmer to remove it from the 088 closer. 4. Remove the top plates. 5. Loosen the gearbelt support mounting screw and slide the gearbelt support away from the cutter blade. 6. Loosen the mounting screw on the idle belt adjustment pulley. Release the tension on the belt. 7. Loosen the mounting screw on the front idle pulley, and slide the pulley away from the cutter blade. 8. Loosen the mounting screw on the drive belt adjustment pulley, and remove the old belt. 9. Install the new belt and tension with the adjustment pulley. Tighten the mounting screw. 088A E

66 Appendix 10. Slide the front idle pulley toward the cutter blade until the feed belts make contact. The tooth of one belt should engage between the teeth of the opposite belt. Tighten the mounting screw. 11. Move the idle belt adjustment pulley away from the front pulley to tension the belt. Tighten the mounting screw. 12. Slide the gearbelt support toward the cutter blade. The gearbelt support should be very close to the belt, but not make contact with the belt. Tighten the fastener. 13. Install the top plates. 14. Mount the trimmer on the 088 closer. Make sure the hex coupler drive pin fully engages into the drive fastener. Manually move the trimmer feed belts if needed to allow the drive to engage. G. REPLACE FEED BELT IDLE SIDE: Figure 5 1. Disconnect the 088 closer power cord from the electrical source. 2. Loosen the two locking knobs that hold the trimmer to the mounting brackets. 3. Pull up on the trimmer to remove it from the 088 closer. 4. Remove the top plates. 5. Loosen the gearbelt support mounting screw and slide the gearbelt support away from the cutter blade. 6. Loosen the mounting screw on the idle belt adjustment pulley. Remove the tension on the belt. 8. Remove the idle belt, and replace with the new belt. 9. Slide the front idle pulley toward the cutter blade until the feed belts make contact. The tooth of one belt should engage between the teeth of the opposite belt. Tighten the mounting screw. 10. Move the idle belt adjustment pulley away from the front pulley to tension the belt. Tighten the mounting screw. 11. Slide the gearbelt support toward the cutter blade. The gearbelt support should be very close to the belt, but not make contact with the belt. Tighten the fastener. 12. Install the top plates. 13. Mount the trimmer on the 088 closer. Make sure the hex coupler drive pin fully engages into the drive fastener. Manually move the trimmer feed belts if needed to allow the drive to engage. H. ADJUST GEARBELT SUPPORT: Figure 5 1. Disconnect the 088 closer power cord from the electrical source. 2. Remove the top plates. 3. Loosen the gearbelt support mounting screw. 4. Slide the gearbelt support toward the cutter blade. The gearbelt support should be very close to the belt, but not make contact with the belt. 5. Tighten the gearbelt support mounting screw. 6. Install the top plates. 7. Loosen the mounting screw on the front idle pulley, and slide the pulley away from the cutter blade. F 088A 09 10

67 Appendix TROUBLE SHOOTING PROBLEM A. Trimmer feed belts do not run CAUSE 088 closer not running Drive coupler not engaged Worn drive coupler Bag material in drive assembly CORRECTION Make sure 088 is turned on. Make sure trimmer drive is correctly engaged to closer drive. Inspect trimmer and closer drive coupler for wear. Replace as needed. Clean the drive assembly. Remove belts and pulleys as needed to inspect bearings. B. Trimmer noisy Drive coupler not engaged Worn drive coupler Bag material in drive assembly Make sure trimmer drive is correctly engaged to closer drive. Inspect trimmer and closer drive coupler for wear. Replace as needed. Clean the drive assembly. Remove belts and pulleys as needed to inspect bearings. C. Bags are not cut Cutter blade is dull Replace cutter blade. D. Bag jamming in trimmer Feed belts extremely loose and support belt loose or missing Bag scraps caught in machine Cutter blade dull or damaged Properly tension feed belts and adjust support belt.r Clean out bag scraps. Inspect and replace blade. 088A G

68 Appendix 088 TRIMMER PARTS IDENTIFICATION H Figure 6 088A 10 10

69 Appendix 088 TRIMMER PARTS IDENTIFICATION (Figure 6) ITEM PART NO. NUMBER DESCRIPTION QTY BUSHING - PULLEY PULLEY BELT - UPPER IDLE R FRAME - TRIMMER L FRAME - TRIMMER BAR - BACK BAR - SIDE COVER - TOP DRIVE COVER - TOP IDLE R GUARD - NOSE - DRIVE L GUARD - NOSE - DRIVE R GUARD - NOSE - IDLE L GUARD - NOSE - IDLE MOUNT - TRIMMER MOUNT - BEARING WALL - VACUUM CHAMBER DRIVE WALL - VACUUM CHAMBER IDLE BUSHING - BLADE NUT - DRIVE SHAFT SUPPORT - BELT COUPLER - DRIVE PLATE - UPPER TRIM STUD 2 088A I

70 Appendix 088 TRIMMER PARTS COMMON ITEM PART NO. NUMBER DESCRIPTION QTY CUTTER BLADE - BAG TRIMMER 1 22 *Z KIT - PULLEY - IDLE - GEAR 1 23 **Z KIT - PULLEY - IDLE - FLAT W-001 SP WASHER W-002 S WASHER 2 26 P BEARING - 1/4 B. X 5/8 O.D. X.2 W P BELT - TIMING GATES TP126XL P KNOB 2 29 P SCREW - NO 4 X 7/16 HI-LO PPH F S WASHER - NO 10 FLAT 4 31 F03-190F S NUT UNF HEX 4 32 F06-250C04 SCREW - 1/4-20UNC X 1/4 LG SKT SET 2 33 F10-164C04 S SCREW UNC X 1/4 LG SKT HD CAP 4 34 F10-164C08 S SCREW UNC X 1/2 LG SKT HD CAP 4 35 F10-250F06 SCREW - 1/4-28UNF X 3/8 LG SKT HD CAP 1 36 F11-164C06 S SCREW UNC X 3/8 LG SKT BTN HD F11-164C08 S SCREW UNC X 1/2 LG SKT BTN HD 6 38 F11-190F05 S SCREW UNF X 5/16 LG SKT BTN HD 2 39 F11-190F14 S SCREW UNF X 7/8 LG SKT BTN HD 5 40 F12-112C10 S SCREW UNC X 5/8 LG SKT FLT HD 2 41 F12-164C04 S SCREW UNC X 1/4 LG SKT FLT HD 2 *Z KIT - PULLEY IDLE - GEAR consists of: PULLEY - HALF QTY 2 P BEARING 1 P SCREW - NO 4 X 7/16 4 **Z KIT - PULLEY - IDLE - FLAT consists of: PULLEY - HALF - IDLE QTY 2 P BEARING 1 P SCREW - NO 4 X 7/16 4 These parts can be ordered separately or as an assembly by "KIT" number. J 088A 09 10

71 Appendix SUGGESTED SPARE PARTS INVENTORY FOR THE TYPE 088A CLOSER Part Description Qty Spring - Anti Backup Belt - Upper Idle Belt - Lower Idle Mount - Breakoff Link Cutter Blade 1 0S-006 S Spring 1 0S-012 Spring 1 0S-018 Spring 2 0S-043 Spring 1 0S-054 Spring 1 0S-062 Spring 1 0S-079 Spring 1 0W-001P Washer 2 P Belt - Gear 2 P Belt - Gear 1 P Sensor - Magnetic 1 P Washer - Nylon 4 Z Kit - Pulley - Idle Gear 2 Z Kit - Pulley - Idle Flat 2 NOTE: Specify on the order the TYPE, MODEL, and SERIAL NUMBER of the machine for which the parts are ordered. This information will be found on the machine s nameplate. CONTACT THE FACTORY FOR CURRENT PRICES. Kwik Lok WARRANTY POLICY Seller warrants that the equipment shall be free of defective workmanship or materials. Its obligation under this warranty to consist exclusively of repairing or replacing, free of charge f. o. b. its factory, any parts received at its factory within two years from the date of shipment of the respective equipment or parts alleged to be defective and determined by Seller upon inspection to be defective. No other warranty, expressed or implied, as to description, quality, merchantability, fitness for a particular purpose, or any other matter is given by Seller in connection with this sale. Under no circumstances shall Seller be liable for loss or profits or other consequential damages, or for any other direct or indirect costs, expenses, equipment or any part thereof. Neither shall the Seller be liable for any defects attributable to the use of any parts, supplies or service not manufactured, supplied or provided by the Seller. Electric motors and controls carry a one year warranty in which motors or controls will be repaired and returned to the Buyer at no charge if the manufacturer determines the equipment to be defective in workmanship and / or materials. 088A K