EchoMaster Display Assembly Instructions

Size: px

Start display at page:

Download "EchoMaster Display Assembly Instructions"

Dorothy Warren
5 years ago
Views:

1 EchoMaster Display Assembly Instructions

Wall Display Wiring PARTS KIT CONTENTS: 1- ATCFB12 (FUSE BLOCK) 12-

RING TERMINAL 1- NIBCYS YELLOW BUTT CONNECTOR 1-12V 10A POWER

CONNECT EACH POWER WIRE USING A FEAMLE QUICK DISCONNECT TO THE FUSE

2 Wall Display Wiring PARTS KIT CONTENTS: 1- ATCFB12 (FUSE BLOCK) 12- FIFR PINK FEMALE QUICK DISCONNECT 12- ATC1 1 AMP FUSES 1- IRR10 RED RING TERMINAL 1- NIBCYS YELLOW BUTT CONNECTOR 1-12V 10A POWER SUPPLY 1. CONNECT RING TERMINAL TO FUSE BLOCK INPUT STUD. 2. CONNECT EACH POWER WIRE USING A FEAMLE QUICK DISCONNECT TO THE FUSE BLOCK. 3. INSERT 1 FUSE PER POWER WIRE. 4. GROUP ALL THE GROUND WIRES TOGETHER INSERT THEM INTO THE YELLOW BUTT CONNECTOR AND CRIMP THEM DOWN SOLIDLY PLUG IN THE POWER SUPPLY TO THE WALL AND ENJOY.

3 Mounting options: 1. There are holes on the rear of the display for standard wall mount applications. 2. Brackets are included with the Display for slat wall applications. Enclosed mounting bracket metal clips into slatwall, then the display clicks overtop Wall Display Mounting

Fuse 2: Tag frame Section 3 Needs 2 Power leads Fuse 1: Monitor Fuse 2: Camera Section 4 Needs 3 Power leads Fuse 1: Monitor power Fuse 2: Cameras

4 PIC 1: Shows all the products mounted before being wired. Mount the ATCFB12 fuse holder and the 10A power supply at this point. Section 1 Needs 3 power leads: Fuse 1: Mirror power Fuse 2: Cameras grouped together Fuse 3: Switches Section 2 Needs 2 Power leads: Fuse 1: Mirror Fuse 2: Tag frame Section 3 Needs 2 Power leads Fuse 1: Monitor Fuse 2: Camera Section 4 Needs 3 Power leads Fuse 1: Monitor power Fuse 2: Cameras grouped together Fuse 3: Switches Section 5 Needs 2 Power leads Fuse 1: Front parking sensor Fuse 2: Rear parking sensor PIC 1 PIC 2: Shows the display and complete. PIC 2

Panel #1 PARTS: PMK-733BS KIT (PMM-733-PL, angled mirror mount (2) PCAM BSM-1, LP01 TAG MOUNT CAMERA, 3 MOMENTARY SWITCHES) Connect 12V (+) power and 12V (-) ground to the Mirror and each camera.

5 Panel #1 PARTS: PMK-733BS KIT (PMM-733-PL, angled mirror mount (2) PCAM BSM-1, LP01 TAG MOUNT CAMERA, 3 MOMENTARY SWITCHES) Connect 12V (+) power and 12V (-) ground to the Mirror and each camera. Connect 12V (+) power to one side of each momentary switch. Video 1 to Left camera using 1 RCAS male RCA adaptor, Purple Trigger to momentary switch 12V (+) Video 2 to Right camera using 1 RCAS male RCA adaptor, White trigger to momentary switch 12V (+) Reverse to the LP01 tag mount camera using 1 RCAS male RCA adaptor, Green trigger to momentary switch 12V (+)

6 PANEL #2 PARTS: CAM-LF3B, MM-4320-DVR, angled mirror mount Wire the MM-4320-DVR & CAM-LF3B to Power and ground. Upon powering up the screen, the DVR screen will be displayed and recording will start automatically, as long as an SD card is inserted. Use the supplied RCAS (male rca adaptor) to connect the video out of the tag frame camera to the reverse camera input (Video 2) of the MM-4320-DVR. The mirror has automatic video signal sensing, which will display the camera image on the screen.

Panel #3 P-MON-50FM, CAM-MV6, MOMENTARY SWITCH PMON-50-FM WIRING: Video1: Connect to CAM-MV6 Red 12V (+) Black 12V (-) Ground Green 12V (+) Reverse Tigger (connect with red wire above) CAM-MV6

7 Panel #3 P-MON-50FM, CAM-MV6, MOMENTARY SWITCH PMON-50-FM WIRING: Video1: Connect to CAM-MV6 Red 12V (+) Black 12V (-) Ground Green 12V (+) Reverse Tigger (connect with red wire above) CAM-MV6 WIRING: Red 12V (+) Black 12V (-) Ground White: Momentary 12V(+) The P-MON-50 FM s video 1 input will be connected to the CAM-MV6. The CAM-MV6 multi-view button has to be mounted vertically center above the camera. This allows switching of the 4 rear views. The momentary switch will be mounted vertically center in between the CAM-MV6 and the Multiview button. The reverse image white wire will need to tagged to each side of the momentary switch. When the momentary switch is held down, the two front views will be displayed.

PMON-50-FM WIRING: Video1: Connect to VS41 Red 12V (+) Black 12V (-) Ground Green 12V (+) Reverse Tigger (connect with red wire above) VS41 WIRING:

8 Panel #4 PARTS: P-MON-50FM, CAM-DPL, PCAM220, PCAM201, PAC VS41, 3) MOMENTARY SWITCHES Only video 1 input needs to used on MON-50. You will need to wire in the PAC VS41 video switcher in order for the 3 camera images to be shown on the monitor. PMON-50-FM WIRING: Video1: Connect to VS41 Red 12V (+) Black 12V (-) Ground Green 12V (+) Reverse Tigger (connect with red wire above) VS41 WIRING: Video Out: goes to MON-50 s video 1 input. Video2: Grey trigger (+) to PCAM220 momentary switch Video1: White trigger (+) to CAM DPL s momentary switch Video3: Green trigger (+) to PCAM201 momentary switch

9 Panel #5 PARTS: PS-RDIS-M, PS-FDIS-W, (2)PA-DISPLAY Install and wire each sensor kit to power and ground. Mount a PA DISPLAY and wire into each module instead of the supplied speaker. But the speaker needs to be mounted to show that it comes with the kit and the PA DISPLAY is a optional upgrade.

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Toyota 24-pin Dual Camera Blind Spot Monitoring System (Kit # 9002-2911) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: 2 Adjustable