ISIS Power Manual and Installation Guide Race Car Replicas- Superlite Coupe

Size: px
Start display at page:

Download "ISIS Power Manual and Installation Guide Race Car Replicas- Superlite Coupe"

Transcription

1 ISIS Power Manual and Installation Guide Race Car Replicas- Superlite Coupe Table of Contents Overview... 2 System Details... 3 Kit Includes... 3 Technical Specifications... 3 Harness Descriptions... 4 Cabin Harness... 5 CAN Cable B... 6 Front Harness... 7 Rear Harness A... 8 Rear Harness B... 9 MASTERCELL Harness with H-Bridge Module Mounting the Cells Wiring Primary Power and Mega Fuses Wiring the Rear POWERCELL Wiring the Front POWERCELL Wiring Dash Cluster Feeds Wiring Power to the Vintage Air System Wiring Hydraulic Pump to POWERCELL Harness Wiring Power and Ground to the Steering Column Wiring Front Harness Wiring the MASTERCELL Harness Connecting the CAN Cables Connecting the Cooling Fan Trigger Wire to the GM Fuse Box Using the ISIS inlink Key Fobs Appendix 1: Connecting Cooling Fan Input to MASTERCELL Connector Appendix 2: Configuration Details for the ISIS SLC Kit Warranty Information Contact Information

2 Overview Your new Race Car Replicas Superlite Coupe comes with a complete wiring harness and electrical system from ISIS Power. This is a turn-key electrical system that gives you all of your switched electrical functions and more. Using OEM multiplexing technology, ISIS allows you to reduce weight in your car plus increase the functionality of the overall electrical system. This manual is designed to walk you through the process of wiring your car. See the appendices in the end of the document for pictures that identify the harnesses included in your kit. Please consult the 3-Cell Kit Manual from the ISIS Power website ( for more specifics on the ISIS Intelligent Multiplex System. 2

3 System Details ISIS 3-Cell Kit (1 L1 MASTERCELL and 2 L1 POWERCELLs) inlink RF Wireless System with 2 Key Fobs Custom engineered wiring harness for Superlite Coupe Kit Includes ISIS L1 MASTERCELL with RCR SLC Code Installed and inlink ISIS L1 POWERCELL V ISIS L1 POWERCELL V MASTERCELL Harness with H-Bridge Module FRONT HARNESS REAR HARNESS A REAR HARNESS B Cabin HARNESS 46 POWER CABLE 110 POWER CABLES CAN CABLE-POWERCELL 1 to MASTERCELL CAN CABLE- POWERCELL 2 to POWERCELL 1 3-WAY MEGA FUSE Ground harness for fans & horn Ground harness for hydraulic switch Ground harness for AC Clutch 4-Gauge Power Feed ISIS inlink Key Fobs Dummy Plug- B MASTERCELL Fuse Assortment Dummy Plug- POWERCELL Inputs MASTERCELL Terminal Resistor Technical Specifications MASTERCELL is rated to 85 ⁰C or 185 ⁰F. POWERCELLs are rated to 125 ⁰C or 257 ⁰F. Battery voltage range: 11.8 to 15.5 volts 3

4 Harness Descriptions The following pages show you the different harnesses and identify the connections that plug into the ISIS system. Please use these as a guide as you install the system in your car. Harnesses General Vehicle Layout 4

5 Cabin Harness 5

6 CAN Cable B 6

7 Front Harness 7

8 Rear Harness A 8

9 Rear Harness B 9

10 MASTERCELL Harness with H-Bridge Module 10

11 Mounting the Cells The RCR body panels have mounting holes pre-cut in them for the ISIS MASTERCELL and POWERCELLs. Use 1/4-20 bolts to mount cells to the body panels. Bolts should be tightened so that they are snug but do not over-tighten to crush the mounts. The POWERCELLs each have a unique address that identifies the cell to the MASTERCELL. There are red jumpers that set the address on each cell. The cell set as address 1 is to be mounted in the front of the car. POWERCELL 2 should be mounted in the rear of the car. Figure 1 shows the jumper configurations to identify the front and rear POWERCELLs. Figure 1: Identifying the Front & Rear POWERCELLs 11

12 Wiring Primary Power and Mega Fuses 1. Mount the Mega fuse holder assembly near the battery in the car. 2. Connect the Three 8-AWG primary power feeds to the individual fuses in the holder. See Figure 2. Figure 2: Connecting the power feeds to the Mega fuse holder. Please note that there will only be three Mega-Fuse holders instead of the four shown below. 12

13 3. Connect the 4-AWG main power feed to the buss bar on the Mega fuse holder. See Figure 3. Figure 3: Connecting primary power to the buss bar. 4. Connect the other end of the 4-AWG power feed to the positive terminal on the battery. 13

14 Wiring the Rear POWERCELL Figure 4: Rear POWERCELL Diagram B CR1 CR2 P1 P2 P3 A 1. Mount the rear POWERCELL on the back firewall next to the GM fuse box for the engine management system. 2. Connect the single red 8-gauge power feed from the Mega fuse block to socket P1. Insert the POWERCELL Input Dummy plugs into sockets P2 & P3. See Figure Plug the POWERCELL rear harness A into socket A. Plug the POWERCELL rear harness B into socket B. See Figure 4. 14

15 4. Connect the ground connections from POWERCELL rear harnesses A & B to chassis ground on the body. 5. Connect the starter solenoid lead (white wire) off of the POWERCELL rear harness B to the S-terminal on the starter solenoid. 6. Connect the switched ignition lead (yellow wire) off of the POWERCELL rear harness A to the ignition relay coil on the GM fuse box. 7. Connect the A/C clutch lead (tan wire) off of the POWERCELL rear harness A to the input terminal on the air conditioning clutch on the compressor. Attach the included ground wire to the other terminal on the air conditioning clutch and properly ground this to the chassis. 8. Run the length of the POWERCELL rear harness B to the back of the car. Connect the splices to the right and left tail light assemblies. Use the following table to identify the wire colors. Wire Color Brown Violet Light-Green Black Function Left-Turn Signal / Brake Light Right-Turn Signal / Brake Light Parking Light Ground 15

16 Wiring the Front POWERCELL Figure 5: Front POWERCELL Diagram 1. Mount the rear POWERCELL on the kick panel to the left of the driver s feet. 2. Connect the red 8-gauge power feeds from the Mega fuse block to sockets P1 and P2. See Figure Connect the fused constant power feed from the Cabin Harness for the dash to P3. 4. Connect the ground ring-terminal to the chassis. 5. Mount the in-cabin bulk-head connector to the front bulk-head of the car. 16

17 Wiring Dash Cluster Feeds Use the following table to connect the dash-cluster feeds from the cabin POWERCELL harness to the instrument cluster. Strip and crimp the mating terminals to the POWERCELL harness to the harness included with the instrument cluster. POWERCELL Harness Wire Instrument Cluster Wire Function Red Red Constant power Light-Green Brown Switched ignition power Blue Yellow High-beam indicator Violet White Right-turn signal indicator Brown Gray Left-turn signal indicator Wiring Power to the Vintage Air System Use the following table to connect the Cabin Harness to the Vintage Air system. See the Vintage Air instructions for more details. Ground the Vintage Air per their instructions. POWERCELL Harness Wire Instrument Cluster Wire Function Red Red Constant power Light-Blue Purple Switched ignition power 17

18 Wiring Hydraulic Pump to POWERCELL Harness The POWERCELL cabin harness has a branch that leads to the dash console. This includes feeds for the Vintage Air System and the switch for the hydraulic pump for the nose of the car. There are red, pink and gray wires, pre-terminated with ¼ female terminals. These plug onto the male blades on the switch included with your Race Car Replica Kit. Each wire is labeled with its mating terminal on the switch. Plug these wires onto the switch per these labels. There is an included ground harness with your ISIS kit. Connect these terminals to the switch per the labels on the wires. Wiring Power and Ground to the Steering Column The POWERCELL cabin harness has a branch that leads to the steering column. This includes a light-green and black wire. The light-green is switched ignition power for the tilt/telescope mechanism on the column and the wiper control relay. The black is ground. Plug the light-green 14-AWG wire from the Cabin Harness onto the mating terminal on the light-green 14-AWG wire on the MASTERCELL harness. Plug the black 14-AWG wire from the Cabin Harness to the black 22-AWG wire on the MASTERCELL harness. 18

19 Wiring Front Harness 1. Plug the large black bulkhead mating connector onto the connector on the front of the car. 2. Run the left and right runs of the harness to their respective headlight assemblies in the car. 3. Connect the Orange 14-AWG wire in from the harness to cooling fan Connect the Tan 14-AWG wire in from the harness to cooling fan Connect the Green 14-AWG wire in from the harness to the horn. 6. Connect the ground harnesses for the fans and the horn and properly connect this to ground. 7. Connect the Grey 14-AWG and Pink 14-AWG wires to the hydraulic pump for the suspension. Flip these wires if the pump direction is reversed. 19

20 Wiring the MASTERCELL Harness Figure 6: MASTERCELL Diagram 1. Plug the MASTERCELL input connector to the A socket on the MASTERCELL. 2. Plug in the MASTERCELL dummy connector into the B socket on the MASTERCELL. 3. Plug the Delphi connector to the GM steering column connector. 4. Plug the Yellow-Orange 22-AWG wire onto one of the terminals on the brake pedal switch. Plug the Black 22-AWG wire to the other terminal. 5. Connect the Grey connector on the MASTERCELL harness to its mating connector on the GM steering column. 6. Connect White 14-AWG and Orange 14-AWG to the terminals on the wiper motor per Figure 7. Make sure that the wiper motor is properly grounded. 20

21 Figure 7: Wiper Motor Wire Connections. 7. Connect input wires to switches on dash per the following table. Wire Color Function White-Blue Ignition White-Yellow Starter Tan-Yellow One-Button Start White-Red Horn White-Black Output of trinary switch on Vintage Air Controller Yellow-Blue 4-Way Flashers Black Ground* * Use the black wires as the ground reference for the switches. You have the option to use separate inputs for ignition and starter or the ISIS One Button Start. This is an either-or choice. Tape up the unused input wires to make sure that they do not accidentally contact ground or other inputs. If you choose to use separate inputs for the ignition and starter, you can either use a traditional keyed switch or separate switches. Use the black wires included in this harness to ground one side of the switch. The input wire corrects to the other terminal on the switch. In the case of a traditional keyed ignition switch, connect the ignition wire to the IGN terminal on the switch, the starter wire to START and connect one of the black ground wires to the B+ terminal. 21

22 If you choose to use the one button start, simply connect the Tan-Yellow input wire to a momentary button. Connect one of the black ground wires to the other terminal on the switch. The ISIS One-Button Start function works this way. Pressing and releasing the button turns on the ignition and switched accessories. Pressing and releasing the button again will turn off the ignition and switched accessories. To start the car, press and hold the button. The ignition will turn on and after 1 second, the starter will crank. Hold the button until the engine starts. When it is released the starter will drop out but the ignition and switched accessories will be powered. To shut off the engine, press and release the button again. 22

23 Connecting the CAN Cables 1. Connect CAN Cable A to socket CM1 on the MASTERCELL and socket CF2 on the front POWERCELL. 2. Connect CAN Cable B to socket CR1 on the rear POWERCELL and socket CF1 on the front POWERCELL. 3. Plug the CAN terminator plug into socket CR2 on the rear POWERCELL. 4. Connect the wires on the rear end of CAN Cable B per this table. Wire Color Function Green-Blue Fuel Level Sender Blue-Yellow Cooling Fan Trigger to GM Fuse Box Violet-Blue Wheel Speed Sensor Violet-Red Un-assigned gauge sender* Pink-Green Un-assigned gauge sender* Pink-Yellow Un-assigned gauge sender* Pink-Blue Un-assigned gauge sender* Pink-Black Un-assigned gauge sender* * Connect these wires to senders on engine as necessary to control gauges. 1. Connect the wires on the front end of CAN Cable B per this table. Wire Color Function Green-Blue Fuel Level Gauge Blue-Yellow Socket 5 on MASTERCELL A Connector (See Appendix 1) Violet-Blue Speedometer on Gauge Cluster Violet-Red Un-assigned gauge sender* Pink-Green Un-assigned gauge sender* Pink-Yellow Un-assigned gauge sender* Pink-Blue Un-assigned gauge sender* Pink-Black Un-assigned gauge sender* * Connect these wires to gauges as necessary. 23

24 Connecting the Cooling Fan Trigger Wire to the GM Fuse Box As described in the previous section, the blue-yellow wire going to the MASTERCELL is the cooling fan trigger. It is designed to be spliced into the output of the cooling fan relay on the GM fuse box. Cut the cooling fan wire to length and strip it ½ inch. Crimp the butt-splice connector for the cooling fan trigger wire to the fan output from the GM fuse box and use a heat gun to shrink the protective covering over the wire. Using the ISIS inlink Key Fobs Your ISIS kit for the SLC includes the inlink RF option. From the key fobs, you can control the functions in the car. See Figure 8 for the pre-set functions on the fob. Figure 8: inlink Key Fob Buttons 24

25 When security is enabled from inlink, you will get one flash of the parking lights to verify that it is set. With security enabled, the inputs for the ignition, fuel pump, starter and one-button start are completely disabled. You will note a message on the MASTERCELL insight LCD screen that tells you that security is enabled if you try to activate any of these functions. The MASTERCELL will allow the car to be started only when security is disabled. The parking lights will flash twice to confirm that security is disabled. 25

26 Appendix 1: Connecting Cooling Fan Input to MASTERCELL Connector Follow these instructions to connect the Blue-Yellow wire from the CAN harness into the input connector on the MASTERCELL. 1. Press a small flat-head screwdriver on the white tab and remove the clear retainer. See Figure A1. Figure A1: Removing the MASTERCELL Retainer 2. Once the guide piece has been removed place a small flat head screwdriver at the back of the connector. Pry the plastic piece back and pull the connector apart simultaneously. Repeat for the remaining two. See Figure A2. Figure A2: Opening the MASTERCELL Connector Strain Relief 26

27 3. Place the blue wire with the yellow stripe from CAN cable B into socket 5. See Figure A3. Figure A3: Inserting Blue-Yellow Wire into Cavity 5 4. Place the clear guide cover back on. You may have to press some of the pins down if you feel resistance. Do this using the small screwdriver or by using your hands. Once you have the clear guide cover back on snap the connector together. See Figure A4. Figure A4: Replacing Retainer on MASTERCELL Connector 27

28 Appendix 2: Configuration Details for the ISIS SLC Kit The following tables show you the relationships between the inputs and outputs in the ISIS system. Note that this is specifically designed for the Race Car Replicas Superlite Coupe. 28

29 29

30 30

31 Warranty Information Infinitybox, LLC ( Infinitybox ) warrants against any defects in materials and workmanship to the Product s ISIS modules, wiring harnesses and accessory modules for a period of one (1) year from the first date of purchase. Subject to the terms of this warranty described below, Infinitybox will replace any such defective Product that is returned to Infinitybox within the one (1) year period from initial purchase. Replacement of any defective part or Product will not extend the applicable warranty period. The warranty does not apply to: (i) any Product that is not installed in compliance with the applicable Product documentation; (ii) any defect in, or failure of, the Product resulting from an accident, shock, negligence, water immersion or misuse; (iii) any Product that has been modified, adjusted, repaired, or disassembled by any party other than Infinitybox; or (iv) any defect other than in materials and workmanship. This warranty covers only the original purchaser of Product purchased from an Infinitybox authorized dealer in the United States. In order to receive warranty service, purchaser must provide Infinitybox with a copy of the receipt stating the dealer name, product purchased and date of purchase. Products found to be defective during the warranty period will be replaced (with a product deemed to be equivalent or better) at the discretion of Infinitybox. Infinitybox s sole liability for any defective Product is limited solely to the replacement of Product pursuant to this warranty. Infinitybox reserves the right to replace any repairable parts with new or refurbished parts. INFINITYBOX DISCLAIMS ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY, SUCH AS WARRANTIES OF MERCHANTABILITY AND FITNE SS FOR PURPOSE. IN NO EVENT SHALL INFINITYBOX BE LIABLE FOR ANY PUNITIVE, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LIABILITY FOR LOSS OF USE, LOSS OF PROFITS, LOSS OF PRODUCT OR BUSINESS INTERRUPTION HOWEVER THE SAME MAY BE CAUSED, INCLUDING NEGLIGENCE. 31

32 Contact Information The ISIS Intelligent Multiplex System is a product of Infinitybox, LLC sales@isispower.com 32

Infinitybox, LLC Addendum to Factory Five 818 Configuration Sheet Installation Guide Table of Contents

Infinitybox, LLC Addendum to Factory Five 818 Configuration Sheet Installation Guide Table of Contents Infinitybox, LLC Addendum to Factory Five 818 Configuration Sheet Installation Guide Table of Contents Overview... 2 Wiring Ignition Input to MASTERCELL... 3 Wiring Ignition Outputs to POWERCELLs... 4

More information

INFINITYBOX invironment Heat & A/C Controller Module for Vintage Air Gen-IV Table of Contents

INFINITYBOX invironment Heat & A/C Controller Module for Vintage Air Gen-IV Table of Contents INFINITYBOX invironment Heat & A/C Controller Module for Vintage Air Gen-IV Table of Contents Overview... 2 Kit Includes... 3 Installation Steps... 4 Connect the invironment module to the Vintage Air Gen-IV

More information

Infinitybox Express Road Race Car Kit Installation Guide

Infinitybox Express Road Race Car Kit Installation Guide Table of Contents Infinitybox Express Road Race Car Kit Installation Guide Overview... 2 Warnings... 3 J1939 POWERCELL Technical Details... 4 IOX Input/Output Module Technical Details... 4 Kit Contents...

More information

Setup and Configuration Guide Universal Switch Interface

Setup and Configuration Guide Universal Switch Interface Table of Contents J1939 inmotion Cell Setup and Configuration Guide Universal Switch Interface Overview... 2 Warnings... 3 J1939 inmotion Cell Technical Details... 4 inmotion Cell Installation Steps...

More information

Infinitybox 10 and 20-Circuit Kit Installation Guide

Infinitybox 10 and 20-Circuit Kit Installation Guide Table of Contents Infinitybox 10 and 20-Circuit Kit Installation Guide Warnings... 2 Installation Steps... 3 STEP 1: Mounting the Cells... 4 STEP 2: Running Power from the Battery... 7 STEP 3: Connecting

More information

J1939 POWERCELL Setup and Configuration Guide Universal Switch Interface

J1939 POWERCELL Setup and Configuration Guide Universal Switch Interface Table of Contents J1939 POWERCELL Setup and Configuration Guide Universal Switch Interface Overview... 2 Warnings... 3 J1939 POWERCELL Technical Details... 4 POWERCELL Installation Steps... 5 Mounting

More information

INSTRUCTIONS. 20 Circuit Wiring Kit Instructions October 2009, Speedway Motors, Inc.

INSTRUCTIONS. 20 Circuit Wiring Kit Instructions October 2009, Speedway Motors, Inc. 1 MAIN FUSE PANEL The main fuse panel harness s designed to be mounted under the dash a the firewall in an area close to the steering column. The enclosed representation of the main dash harness shows

More information

INSTRUCTIONS Circuit Wiring Kit Instructions _2017. Fuse Box Connections. (viewed from underside) 2018, Speedway Motors, Inc.

INSTRUCTIONS Circuit Wiring Kit Instructions _2017. Fuse Box Connections. (viewed from underside) 2018, Speedway Motors, Inc. Fuse Box Connections (viewed from underside) 4D 4C 100 50 300 4D 4C 4B 4A 43 107 39 103 3B 2G 104 93 2F 2E 2D 2C 2B 40 69A 102 101 105 2G 2F 2E 3A A 2A B 40A,B 27 69A 106 201, Speedway Motors, Inc. 1 Fuse

More information

40A A 40B. Horn Relay Connector. Brake Switch. Third Brake Light. Brake Switch. Brake Switch. Wires. page 3. Rear Body Feed Wires.

40A A 40B. Horn Relay Connector. Brake Switch. Third Brake Light. Brake Switch. Brake Switch. Wires. page 3. Rear Body Feed Wires. Fuse Box Connections (viewed from underside) 4D 4C 4D 0 50 300 4C 43 7 39 3 6 4 93 A 2G 2F 2E 2D 2C 2B 2G 2F 2E 40 69A 2 1 5 27 69A 3A B 40A,B 11A,B 40A 156 Dimmer Dome Feed page 2 Horn Relay 2D 2 29 40B

More information

UNIVERSAL WIRING HARNESS Installation Manual

UNIVERSAL WIRING HARNESS Installation Manual UNIVERSAL WIRING HARNESS Installation Manual Terminals are provided for most connections on your wiring kit. Following the gauge manufacturer s instructions, use the terminals supplied with your gauge

More information

INSTRUCTIONS 12 Circuit Wiring Kit Instructions

INSTRUCTIONS 12 Circuit Wiring Kit Instructions Fan 47 9 56 4 7 6 72 40 45 48 5 8 6 Gauge Power Temp Sender Headlight Power Power Radio Constant Power Instruments and Dash Rear of Vehicle Ignition and Lights Fuse Panel & Front of Vehicle Horn Alt Excitor

More information

Installation Manual. 12 Automotive Fuse Panel (AFP12) Version 2.2 March 2018

Installation Manual. 12 Automotive Fuse Panel (AFP12) Version 2.2 March 2018 Installation Manual 12 Automotive Fuse Panel (AFP12) Version 2.2 March 2018 Table of Contents Introduction... 2 What s Included... 3 Installation... 4 Features & Helpful Tips... 9 WAS492 Wire Harnesses...

More information

UNIVERSAL GAUGE WIRE HARNESS

UNIVERSAL GAUGE WIRE HARNESS 2650-1797-00 UNIVERSAL GAUGE WIRE HARNESS For Installing Auto Meter Electric Speedometer, Tachometer, And Short Sweep Electric Oil Pressure, Water Temperature, Fuel Level, and Volt Meter Gauges. This harness

More information

jegs.com

jegs.com Contents Wiring Harness w/ Fuse Panel Installation Instructions Turn Signal Plug w/ Terminals 2 Headlight Plugs 3/4 Grommet 10 ¼ Terminals 4 Ring Terminals 10 Wire Ties Fusible Link 2 Screws & Nuts 2 Plastic

More information

-----

----- ----- - - -- - - -- - -- - - NOTE: #32 WIRE DOES NOT APPLY TO 8 AND 14 CIRCUIT HARNESSES ELECTRIC FAN #1 TO FAN SWITCH (GRAY) #21 TEMP. GAUGE (GREEN) #2 TO AC SWITCH (BLACK) JUMPER WIRE ALTERNATORS

More information

Instrument Cluster 30 33B 39B A B C D E F E F G H J. Connector. Circuit Branch #4. Circuit Branch #5. Circuit. Branch #6 150A. Ground.

Instrument Cluster 30 33B 39B A B C D E F E F G H J. Connector. Circuit Branch #4. Circuit Branch #5. Circuit. Branch #6 150A. Ground. 16 4D, 43 4B 4A & 130 100 50 39A,B,C 300 4C 4B 4C 107 3C 3D 3C 3G 3B 3F 3A 16A 3G 116 104 93 3B 3D 2E 16A 2C 2D 2B 2A 44 40 27A 40B 115 27 40A,C,E 8A,B,C Mating is plugged into accessory connector Power

More information

CLASSIC UPDATE WIRING KIT

CLASSIC UPDATE WIRING KIT by Randy Irwin 1955-57 CLASSIC UPDATE WIRING KIT Randy Irwin - Technical Writer Randy has been involved in the Chevy parts business for over 25 years. He is a wizard at creating, making and modifying custom

More information

Trail Rocker Installation Instructions

Trail Rocker Installation Instructions Trail Rocker Installation Instructions Manual #90580 For Installing Painless Part Numbers: 57000 and 57001 Painless Performance Products recommends you, the installer, read this installation manual from

More information

Rear Body 40D 156A 24 17A 151 3D. 8A,8B,8C under hood light. Horn Relay 91

Rear Body 40D 156A 24 17A 151 3D. 8A,8B,8C under hood light. Horn Relay 91 fuse box as viewed from the wire entry side Mating connector is plugged into Power Accessory connector 40D Rear Body 19 18 9B 30 LH Courtesy Light 40A,D 4D, 43 156B,C 16 16A 4C 3D 3C 16A 3G 4B 3G 116 4A&130

More information

Off-Road Switch Panel Installation Instructions

Off-Road Switch Panel Installation Instructions Off-Road Switch Panel Installation Instructions 50330: Off-road 4 Toggle switches/dash Mount w/keyed Ignition Switch 50332: Off-road 6 Toggle switches/dash Mount w/keyed Ignition Switch Painless Performance

More information

Trail Rocker Installation Instructions

Trail Rocker Installation Instructions Trail Rocker Installation Instructions Manual #90581 For Installing Painless Part Numbers: 57002 Painless Performance Products recommends you, the installer, read this installation manual from front to

More information

DIGIGAUGE P R E S S U R E D I S P L A Y S Y S T E M I N S T R U C T I O N M A N U A L

DIGIGAUGE P R E S S U R E D I S P L A Y S Y S T E M I N S T R U C T I O N M A N U A L DIGIGAUGE P R E S S U R E D I S P L A Y S Y S T E M I N S T R U C T I O N M A N U A L Thank you for purchasing DigiGauge by ZAETECH Disclaimer DigiGauge is for show and off road use only. By using this

More information

COMMANDO REMOTE CONTROL ENGINE STARTER. Limited Warranty Statement MADE IN THE U.S.A. IMPORTANT KEEP YOUR INVOICE WITH THIS WARRANTY STATEMENT!

COMMANDO REMOTE CONTROL ENGINE STARTER. Limited Warranty Statement MADE IN THE U.S.A. IMPORTANT KEEP YOUR INVOICE WITH THIS WARRANTY STATEMENT! Limited Warranty Statement GNU COMMANDO LINE WARRANTY STATEMENT GNU warrants this product to be free from defects in material and workmanship for a period of one (1) year from the date of sale to the original

More information

Wire Harness Installation Instructions

Wire Harness Installation Instructions Wire Harness Installation Instructions For Installing: Part #50001 Race Car Kit/8 Circuit Part #50201 8 Switch Dash Mounted Panel Part #50202 8 Switch Roll Bar Mounted Panel Manual #90502 Painless Performance

More information

20 CIRCUIT ATO FUSE CENTER INSTALLATION INSTRUCTIONS

20 CIRCUIT ATO FUSE CENTER INSTALLATION INSTRUCTIONS 2501 Ludelle Street Fort Worth, Texas 76105 817-244-6212 phone 817-244-4024 fax 800-423-9696 Tech E-Mail: painless@painlessperformance.com Web: www.painlessperformance.com 30003 20 CIRCUIT ATO FUSE CENTER

More information

Camaro Camaro

Camaro Camaro Important facts about this kit. 1. The dash panel used in this picture is used by permission of Covan's Classic. We Make Wiring Easy! 2. This kit requires some modification to your original under dash

More information

accessory connection rear body connection 40G 17A instrument cluster and map lamp ground 150A,B 15A 14A Circuit Branch 500A fog lamp switch

accessory connection rear body connection 40G 17A instrument cluster and map lamp ground 150A,B 15A 14A Circuit Branch 500A fog lamp switch accessory rear body 19 9 11 instrument cluster and map 10A, 0 4 3 7 40G 18 30 17A 24 1A 14A 9 8A instrument cluster 4E 31 3 121 11 33 401 10A 39A 400 30 washer and wiper switch 93A, 94 93 glovebox, map

More information

Replace light bulb with the same number bulb as the one removed. White Wire: Connect to +12 Volt Lighting

Replace light bulb with the same number bulb as the one removed. White Wire: Connect to +12 Volt Lighting INSTALLATION INSTRUCTIONS SHORT SWEEP ELECTRIC GAUGES 2650-1079-00 Rev. C CAUTION FOR ALL GAUGE INSTALLATION (AMMETERS EXCLUDED) As a safety precaution, the +12V wire attached to the positive I (+) terminal

More information

SOLID-STATE POWER DISTRIBUTION

SOLID-STATE POWER DISTRIBUTION SOLID-STATE POWER DISTRIBUTION NEW How it Works The intelligent wiring system is a modular, solid-state microprocessor-controlled automotive electrical system that replaces or augments an existing traditional

More information

MSD SB6 Programmable Ignition for the Kawasaki ZX-14 PN 4219

MSD SB6 Programmable Ignition for the Kawasaki ZX-14 PN 4219 INSTALLATION INSTRUCTIONS MSD SB6 Programmable Ignition for the Kawasaki ZX-14 PN 4219 Parts Included: 1 - Ignition 1 - Wiring Harness 1 - Parts Bag 1 - CD ROM WARNING: When installing the SB6, disconnect

More information

Mustang Classic Update Series Kit

Mustang Classic Update Series Kit accessory rear body 19 9 11 instrument cluster and map 10A, 0 4 3 7 40G 18 30 17A 24 1A 14A 9C 8A instrument cluster 4E 31 3 121 11 401 10A 3 400 30 washer and wiper switch 93A, 93 glovebox, map light,

More information

12 Volt Utility Controller for 4, 6 or 8 Brakes No P

12 Volt Utility Controller for 4, 6 or 8 Brakes No P 12 Volt Utility Controller for 4, 6 or 8 Brakes No. 1300-77 P-1379 819-0094 Installation Instructions Introduction The Warner Electric manually operated Utility Controller operates 4, 6, or 8 twelve-volt

More information

pink relay trigger 12v wire - a fused ignition source relay trigger ground wire-to a good chassis ground to component

pink relay trigger 12v wire - a fused ignition source relay trigger ground wire-to a good chassis ground to component relay logic relay trigger 12v wire - to a fused BASIC RELAY WIRING This relay kit is designed f muli-purpose use. a relay trigger ground wire-to a good chassis ground to component amp A B optional included

More information

NISSAN 370Z INTELLI-KEY Rev.:

NISSAN 370Z INTELLI-KEY Rev.: Remote Starter NISSAN 70Z 009-00 INTELLI-KEY Rev.: 0096 009 Not included: x Fuse 5Amp x s Amp x Relays Override OEM Transponder Immobilizer Via Data (No Key Required). Interfaces directly with the latest

More information

Installation Tips Crimestopper/ProStart Remote Start system + PLJX + DLRM + SPDT (for GM vehicles) T0760 v1.1 updated 2/5/14

Installation Tips Crimestopper/ProStart Remote Start system + PLJX + DLRM + SPDT (for GM vehicles) T0760 v1.1 updated 2/5/14 Installation Tips Crimestopper/ProStart Remote Start system + PLJX + DLRM + SPDT (for GM vehicles) T0760 v1.1 updated 2/5/14 Thank you for purchasing your remote start from MyPushcart.com - an industry

More information

750 Paso Wiring Upgrade

750 Paso Wiring Upgrade 750 Paso Wiring Upgrade Supplies required: 2 Bosch 30A/12V Relays # #0 332 209 150 (with mounting tab) 1 30 Amp fuse holder 1 10 Amp fuse holder 12 inches of brown 12 gauge wire 60 inches of red 14 gauge

More information

Installation Tips for your Crimestopper/ProStart Remote Start system (add-on for GM vehicles) v1.02 updated 1/16/2013

Installation Tips for your Crimestopper/ProStart Remote Start system (add-on for GM vehicles) v1.02 updated 1/16/2013 Installation Tips for your Crimestopper/ProStart Remote Start system (add-on for GM vehicles) v1.02 updated 1/16/2013 Thank you for purchasing your remote start from MyPushcart.com - an industry leader

More information

Installation Instructions For 50330, 50331, 50332, and Off Road Switch Panels

Installation Instructions For 50330, 50331, 50332, and Off Road Switch Panels Installation Instructions For 50330, 50331, 50332, and 50333 Off Road Switch Panels 2501 Ludelle Street Fort Worth, Texas 76105 817-244-6212 Phone 817-244-4024 Fax 888-350-6588 Sales 800-423-9696 Tech

More information

SCHNITZ. Racing SCB-PPI Programmable Power Interrupt Installation and Operation Instructions

SCHNITZ. Racing SCB-PPI Programmable Power Interrupt Installation and Operation Instructions SCB-PPI Programmable Power Interrupt Installation and Operation Instructions Description The SCB-PPI Programmable Power Interrupt is a fully digital and programmable unit used to interrupt the coil charge

More information

Model A Turn Signal Kit Installation Guide

Model A Turn Signal Kit Installation Guide Model A Turn Signal Kit Installation Guide Creative Connections, Inc. Consumer Hot Line: 888-471-LOGO 770-476-7322 In Atlanta, GA http://www.logolites.com P/N: 100-005/K 2008 Creative Connections, Inc.

More information

INSTALLATION INSTRUCTIONS 5.7L HEMI TRUCK HOT-ROD STYLE. Also covers LX 5.7L/6.1L Hemi with Truck or Manual Transmission **

INSTALLATION INSTRUCTIONS 5.7L HEMI TRUCK HOT-ROD STYLE. Also covers LX 5.7L/6.1L Hemi with Truck or Manual Transmission ** INSTALLATION INSTRUCTIONS 5.7L HEMI TRUCK HOT-ROD STYLE Also covers LX 5.7L/6.1L Hemi with Truck or Manual Transmission ** 5.7L Hemi Truck Hotrod Style Page: 2 5.7L Hemi Truck Hotrod Style Page: 3 Our

More information

PIM701 (Police Interface Module) Dodge Charger Pursuit

PIM701 (Police Interface Module) Dodge Charger Pursuit An ISO 9001:2008 Registered Company PIM701 (Police Interface Module) 2015-2017 Dodge Charger Pursuit Introduction The Police Interface Module is intended to provide Dodge Chargers with multiple desired

More information

DASH/MAIN HARNESS. NOTE: wires 400 & 401, must be twisted together.

DASH/MAIN HARNESS. NOTE: wires 400 & 401, must be twisted together. Electric Speedo Ground 151 Turn Flasher 16A 4 150 8A, Cluster Connections 31 33 30 35 151 (electric speedo) 402 401 NOTE: wires 400 & 401, must be twisted together. 156D, E Panel Dimmer 8A 9, C 2D Headlight

More information

INSTRUCTIONS COACH-1 UNIVERSAL WIRING KIT INSTALLATION

INSTRUCTIONS COACH-1 UNIVERSAL WIRING KIT INSTALLATION INSTRUCTIONS COACH-1 UNIVERSAL WIRING KIT INSTALLATION TM 1. IMPORTANT READ ALL INSTRUCTIONS BEFORE YOU BEGIN The electrical system is a critical component affecting both the operation and safety of your

More information

Owner s Manual Electronic Harness Controller P/N ASM4250

Owner s Manual Electronic Harness Controller P/N ASM4250 Owner s Manual Electronic Harness Controller P/N ASM4250 Thunder Heart Performance Corporation MANUAL P/N EI4250 120 Industrial Drive Revision 6/3/04 White House, TN 37188 www.thunder-heart.com TABLE

More information

INSTALLATION MANUAL. Remote Mobile Security System. Model: PL30

INSTALLATION MANUAL. Remote Mobile Security System. Model: PL30 Remote Mobile Security System INSTALLATION MANUAL Model: PL30 Copyright 1998 Magnadyne Corporation For Technical Assistance (800) 638-3600 For Fax on Demand Technical Assistance (800) 994-9977 (Must be

More information

Disconnect the battery power from the car.

Disconnect the battery power from the car. Adding a safety fuse to the ignition circuit of 1956 to 1962 Corvettes Part 1 is for 1958 to 1962. Part 2 is for 1956 to 1957 Rich Mozzetta and Dave Zuberer Part 1-1958 to 1962 Here is a way to add a fuse

More information

Classic Update Series

Classic Update Series Classic Update Series 1964-1966 Ford Mustang START HERE! PLEASE READ THIS EFORE STARTING INSTALLATION! This wiring kit is designed for ease of installation. Please read the guidelines below, EFORE STARTING

More information

INSTALLATION INSTRUCTIONS JEEP WRANGLER TJ HEMI CONVERSION

INSTALLATION INSTRUCTIONS JEEP WRANGLER TJ HEMI CONVERSION INSTALLATION INSTRUCTIONS JEEP WRANGLER TJ HEMI CONVERSION Jeep Wrangler TJ Hemi Conversion Page: 2 Jeep Wrangler TJ Hemi Conversion Page: 3 Our Jeep Wrangler Hemi Conversion harness is designed for the

More information

Headlight Switch Connector. Brake Switch. Lead Wires. Main Power Feed from Starter. Fuse Box Connections (viewed from underside)

Headlight Switch Connector. Brake Switch. Lead Wires. Main Power Feed from Starter. Fuse Box Connections (viewed from underside) www.americanautowire.com 86-933-0801 TH KT DOE NOT UPPORT TOCK (ORGNAL) GENERATOR. THE DEGN OF THE KT DEGNED TO UPPLY MORE POWER THAN THE GENERATOR ALE TO UPPLY. 16 68A 4D 4C 4D 0 0 0 4C 4 43 7 39 3 Dimmer

More information

INSTALLATION MANUAL. Remote Mobile Security System. Model: PL50

INSTALLATION MANUAL. Remote Mobile Security System. Model: PL50 Remote Mobile Security System INSTALLATION MANUAL Model: PL50 Copyright 2000 Magnadyne Corporation For Technical Assistance (800) 638-3600 For Fax on Demand Technical Assistance (800) 994-9977 (Must be

More information

CMD-4000 SERIES REV. A 4+ FUNCTION REMOTE CONTROL DOOR LATCH OPENER SYSTEM INTRODUCTION

CMD-4000 SERIES REV. A 4+ FUNCTION REMOTE CONTROL DOOR LATCH OPENER SYSTEM INTRODUCTION CMD-4000 SERIES REV. A 4+ FUNCTION REMOTE CONTROL DOOR LATCH OPENER SYSTEM INTRODUCTION Thank you for purchasing the CMD-4000 series Remote Control Door Latch Opener System from Dakota Digital, Inc. This,

More information

CMD-4000 SERIES REV. A 4+ FUNCTION REMOTE CONTROL DOOR LATCH OPENER SYSTEM INTRODUCTION

CMD-4000 SERIES REV. A 4+ FUNCTION REMOTE CONTROL DOOR LATCH OPENER SYSTEM INTRODUCTION CMD-4000 SERIES REV. A 4+ FUNCTION REMOTE CONTROL DOOR LATCH OPENER SYSTEM INTRODUCTION Thank you for purchasing the CMD-4000 series Remote Control Door Latch Opener System from Dakota Digital, Inc. This,

More information

Classic Update Series

Classic Update Series Classic Update Series 62-65 Ford Fairlane and 62-63 Mercury Meteor end view of terminal START HERE! PLEASE READ THIS EFORE STARTING INSTALLATION! This wiring kit is designed for ease of installation. Please

More information

Utility Controller Hand Air Operated

Utility Controller Hand Air Operated Utility Controller Hand Air Operated P-1395 819-0288 Installation Instructions Introduction The Warner Electric air/manual Utility Controller combines manual and automatic (air) actuation for the operation

More information

CA 421 Installation Instructions

CA 421 Installation Instructions CA 421 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components

More information

This document describes:

This document describes: Thank you for purchasing this product from ERM Products. We appreciate your interest in our unique product line as we try to offer our customers an alternative to today s traditional products. This universal

More information

510564 OPYRIGHT 2013 American Autowire / Factory-Fit Used with express permission of American Autowire / Factory- Fit Page 1 92971174 Rev 0.0 6/18/2015 UNSEALED ONNETORS The connectors, sockets, wires,

More information

LSx Harness Installation. lsxeverything.com #BecauseYouShould

LSx Harness Installation. lsxeverything.com #BecauseYouShould LSx Harness Installation lsxeverything.com #BecauseYouShould Table of Contents Slide 1 Introduction Page Slide 2 Table of Contents Slide 3 Starting Instructions Slide 4 Power Connections Slide 5 Ground

More information

Dash Logger Extension Cable PART# - RS11850-MD60-EC-11. APPLICATION(S): RIVA/Athena Dash Logger with 2011 & Newer Sea Doo 4-TEC Models

Dash Logger Extension Cable PART# - RS11850-MD60-EC-11. APPLICATION(S): RIVA/Athena Dash Logger with 2011 & Newer Sea Doo 4-TEC Models Dash Logger Extension Cable PART# - RS11850-MD60-EC-11 APPLICATION(S): RIVA/Athena Dash Logger with 2011 & Newer Sea Doo 4-TEC Models This document is broken up into two sections. Proceed to applicable

More information

Classic Update Series

Classic Update Series Classic Update Series 73-79 Ford F100-350 & 78-9 Ford ronco START HERE! PLEASE READ THIS EFORE STARTING INSTALLATION! This wiring kit is designed for ease of installation. Please read the guidelines below,

More information

MSD Kawasaki Jet Ski 750 Enhancer CD Ignition PN 4251

MSD Kawasaki Jet Ski 750 Enhancer CD Ignition PN 4251 MSD Kawasaki Jet Ski 750 Enhancer CD Ignition PN 4251 Parts Included: 1 - MSD Enhancer CD Ignition 2-6mm Stainless Steel Flatwashers 2 - Zip Ties Supplies Required For Installation 1 Tube of Blue Loctite

More information

GTWY605 Fast Idle, Shift Interlock, I/O Chevy 610 Van - 6.0L and 6.6L Engines Contact InterMotive for additional vehicle applications.

GTWY605 Fast Idle, Shift Interlock, I/O Chevy 610 Van - 6.0L and 6.6L Engines Contact InterMotive for additional vehicle applications. An ISO 9001:2008 Registered Company GTWY605 Fast Idle, Shift Interlock, I/O 2009-2017 Chevy 610 Van - 6.0L and 6.6L Engines Contact InterMotive for additional vehicle applications. Introduction The Gateway

More information

C-PIM701 (Police Interface Module) 2018 Dodge Charger Pursuit

C-PIM701 (Police Interface Module) 2018 Dodge Charger Pursuit An ISO 9001:2008 Registered Company C-PIM701 (Police Interface Module) 2018 Dodge Charger Pursuit Introduction The Police Interface Module is intended to provide Dodge Chargers with multiple desired functions

More information

INSTALLATION MANUAL. Model: PLUS For Technical Assistance, please call (800) , or visit

INSTALLATION MANUAL. Model: PLUS For Technical Assistance, please call (800) , or visit R Vehicle Security INSTALLATION MANUAL Model: PLUS-4700 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference;

More information

2JZGTE Installation Manual Firmware Version 3.0

2JZGTE Installation Manual Firmware Version 3.0 2JZGTE Installation Manual Firmware Version 3.0 Warnings: Before proceeding you are obligated to read and agree to the terms and conditions attached to this manual. Misuse of this product may cause injury

More information

Retro it Steering Column

Retro it Steering Column Retro it Steering Column INSTALLATION INSTRUCTIONS for 1970-74 Cuda/Challenger FOR PART NUMBER S: 1620810010, 1620810020, 1620810051, 1620820010, 1620820020, 1620820051 S I NCE 1986 Instruction # 8000000005

More information

Replace light bulb with the same number bulb as the one removed. White Wire: Connect to +12 Volt Lighting

Replace light bulb with the same number bulb as the one removed. White Wire: Connect to +12 Volt Lighting INSTALLATION INSTRUCTIONS SHORT SWEEP ELECTRIC GAUGES 2650-1079-00 Rev. C CAUTION FOR ALL GAUGE INSTALLATION (AMMETERS EXCLUDED) As a safety precaution, the +12V wire attached to the positive I (+) terminal

More information

MSD 7AL-3, Ignition Control PN 7230

MSD 7AL-3, Ignition Control PN 7230 MSD 7AL-3, Ignition Control PN 7230 Important: Read the instructions before attempting the installation. Parts Included: 1-7AL-3, PN 7230 1 - Parts bag (wires and connectors) 4 - RPM Modules 3000, 7000,

More information

INSTALLATION MANUAL. Model: PLUS Vehicle Security

INSTALLATION MANUAL. Model: PLUS Vehicle Security R Vehicle Security INSTALLATION MANUAL Model: PLUS-5000 Copyright 1999 Magnadyne Corporation For Technical Assistance (800) 638-3600 For Fax on Demand Technical Assistance (800) 994-9977 (Must be a Registered

More information

Toggle Button Kit. Installation Instructions MK5 / MK6 Golf, MK5 Jetta

Toggle Button Kit. Installation Instructions MK5 / MK6 Golf, MK5 Jetta Toggle Button Kit Installation Instructions MK5 / MK6 Golf, MK5 Jetta Thank you for choosing the Double Apex Toggle Button kit. If you have any questions about the installation please do not hesitate to

More information

Gas Spreader PLUS Remote Kit With Built in Clutch Relay and On/Off Switch

Gas Spreader PLUS Remote Kit With Built in Clutch Relay and On/Off Switch Gas Spreader PLUS Remote Kit With Built in Clutch Relay and On/Off Switch NOTE: Read all directions first before continuing. This wireless controller kit has been programmed and tested before shipping.

More information

FAST XIM. XIM Unit Installation

FAST XIM. XIM Unit Installation 1 INSTRUCTIONS XIM Thank you for choosing products; we are proud to be your manufacturer of choice. Please read this instruction sheet carefully before beginning installation, and also take a moment to

More information

Step 1 : Starting the installation

Step 1 : Starting the installation Installation Instructions for GM Remote Start w/ INTSL Interface Pre-wired Review the remote start installation manual for safety instructions! Overview Your kit consists of two modules a remote start

More information

NISSAN MAXIMA INTELLI-KEY Rev.:

NISSAN MAXIMA INTELLI-KEY Rev.: Remote Starter NISSAN MAXIMA 2009-2011 INTELLI-KEY Rev.: 20091126 20110921 Not included: 1x Fuse 15Amp 3x s 3x Relays Override OEM Transponder Immobilizer Via Data (No Key Required). Interfaces directly

More information

Chevy INSTRUMENT CLUSTER CONNECTION KIT WIRING INFORMATION FOR A STOCK CHEVY CLUSTER GREY PINK S + FUEL TEMP S + LAMP LAMP HI BEAM

Chevy INSTRUMENT CLUSTER CONNECTION KIT WIRING INFORMATION FOR A STOCK CHEVY CLUSTER GREY PINK S + FUEL TEMP S + LAMP LAMP HI BEAM WIRING INFORMATION FOR A STOCK 1955-56 CEVY CLUSTER 1955-56 Chevy Terminals and connectors are provided for installation to a stock 1955-56 dash cluster. Pigtail connections are provided for the instrument

More information

CSI-300 Installation Instructions

CSI-300 Installation Instructions CSI-300 Installation Instructions Kit Contents Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces

More information

Installation Tips for your Crimestopper/ProStart Remote Start system (for GM vehicles) v1.01 updated 2/27/2012

Installation Tips for your Crimestopper/ProStart Remote Start system (for GM vehicles) v1.01 updated 2/27/2012 Installation Tips for your Crimestopper/ProStart Remote Start system (for GM vehicles) v1.01 updated 2/27/2012 Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing

More information

Installation Tips for your Remote Start system (for RS4LX>GMBP for GM vehicles)

Installation Tips for your Remote Start system (for RS4LX>GMBP for GM vehicles) Installation Tips for your Remote Start system (for RS4LX>GMBP for GM vehicles) Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing remote starts to doit-yourself

More information

Installation Instructions

Installation Instructions Installation Instructions for EVS II Security and Keyless Entry Systems Note: It is recommended that this installation take place prior to rustproofing. The individual delivering the vehicle should review

More information

Aftermarket Interface Module

Aftermarket Interface Module An ISO 9001:2008 Registered Company Aftermarket Interface Module (2015-2018 Ford Transit) AIM514-B High Side Solenoid type Coolant Valve Control AIM515-B Motor Reversing type Coolant Valve Control Introduction

More information

Retro it Steering Column

Retro it Steering Column Retro it Steering Column INSTALLATION INSTRUCTIONS for 1976-86 CJ5 & CJ7 FOR PART NUMBER S: 1520800010, 1520800020, 1520800051, 1526800010, 1526800020, 1526800051 S I NCE 1986 Instruction # 8000000010

More information

PLATINUM Sport Haltech GM LS1 / LS6 Terminated Engine Harness (HT045650) QUICK START GUIDE

PLATINUM Sport Haltech GM LS1 / LS6 Terminated Engine Harness (HT045650) QUICK START GUIDE PLATINUM Sport 2000 Haltech GM LS1 / LS6 Terminated Engine Harness (HT045650) QUICK START GUIDE LIMITED WARRANTY Lockin Pty Ltd trading as Haltech warrants the Haltech TM Programmable Fuel Injection System

More information

2006+ Toyota Yaris Remote Start Wiring Guide

2006+ Toyota Yaris Remote Start Wiring Guide 2006+ Toyota Yaris Remote Start Wiring Guide Note: This guide assumes that the user has a good working knowledge of automotive electrical systems. The user assumes all liability for any damage resulting

More information

Headlight Switch Connector. Brake Switch. Lead Wires. Main Power Feed from Starter

Headlight Switch Connector. Brake Switch. Lead Wires. Main Power Feed from Starter 40 3C 40, 2E 2C 2 2F Dimmer witch 12 11 & 11 2C 2 Horn Relay Dome Courtesy feed 40 16 Main Power Feed from tarter 2 12 V attery rake witch rake witch 40 17 17 rake witch Third rake Light Headlight witch

More information

Installation and Operation Guide

Installation and Operation Guide Bus-Scan CR2 RF Installation and Operation Guide All Content and Information are Copyright 2018 Robotics Technologies, Inc. Features and Information are subject to change without notice. All Rights Reserved.

More information

CA-510a Installation Instructions

CA-510a Installation Instructions CA-510a Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Kit Contents Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting

More information

12 Volt Utility Controller for 4, 6, or 8 Brakes No

12 Volt Utility Controller for 4, 6, or 8 Brakes No 12 Volt Utility Controller for 4, 6, or 8 Brakes No. 1300-76 P-1396-WE 819-0301 Installation Instructions An Altra Industrial Motion Company Contents Introduction... 2 Installation... 3 Mounting Under

More information

This document describes:

This document describes: Thank you for purchasing this product from ERM. We appreciate your interest in our unique product line as we try to offer our customers an alternative to today s traditional products. This programmable

More information

Toyota Supra MKIII Installation Manual Firmware Version 3.1

Toyota Supra MKIII Installation Manual Firmware Version 3.1 Toyota Supra MKIII Installation Manual Firmware Version 3.1 Warnings: Before proceeding you are obligated to read and agree to the terms and conditions attached to this manual. Misuse of this product may

More information

BOM505 Black Out Module Ford F-150 Contact InterMotive for additional applications

BOM505 Black Out Module Ford F-150 Contact InterMotive for additional applications An ISO 9001:2008 Registered Company BOM505 Black Out Module 2015-2016 Ford F-150 Contact InterMotive for additional applications Introduction The BOM505 module has the ability to eliminate all exterior

More information

MSD-8 Plus Ignition PN 7805

MSD-8 Plus Ignition PN 7805 MSD-8 Plus Ignition PN 7805 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the MSD R&D team

More information

e-ask electronic Access Security Keyless-entry

e-ask electronic Access Security Keyless-entry e-ask electronic Access Security Keyless-entry Multiplex System Multiplex System Installation & Instructions (UM15 ~ 22272-03) Table of Contents Introduction... 1 Standard e-fob Operation and Features...

More information

Installation and Operation Guide

Installation and Operation Guide Bus-Scan 500 RF Installation and Operation Guide All Content and Information are Copyright 2018-2019 Robotics Technologies, Inc. Features and Information are subject to change without notice. All Rights

More information

SP EVO-CHR4 (A)

SP EVO-CHR4 (A) TIP SHEET Installation Tips for SP-502 + EVO-CHR4 (A) Remote Start / Alarm T1630 Chrysler 300 (2008-2011) Dodge Magnum (2008) Chrysler Town and Country (2008-2015) Dodge RAM (2009-2012) Dodge Challenger

More information

CAPACITOR ACTUATED PORTABLE STARTER CAPS USER GUIDE. INST048 Doc 3.01

CAPACITOR ACTUATED PORTABLE STARTER CAPS USER GUIDE. INST048 Doc 3.01 CAPACITOR ACTUATED PORTABLE STARTER CAPS USER GUIDE INST048 Doc 3.01 CONTENTS General Information...2 Charts...3 Before First Use...4 Safety Requirements...5 What to Expect from the CAPS...5 CAPS Diagram...6

More information

30140 F5 Dual Fan Controller

30140 F5 Dual Fan Controller 30140 F5 Dual Fan Controller 1 2501 Ludelle Street Fort Worth, Texas 76105 817-244-6212 Phone 817-244-4024 Fax 888-350-6588 Sales 800-423-9696 Tech E-mail: painless@painlessperformance.com Web: www.painlessperformance.com

More information

CP 634 DELUXE 4-CHANNEL KEYLESS ENTRY SYSTEM

CP 634 DELUXE 4-CHANNEL KEYLESS ENTRY SYSTEM CP 634 DELUXE 4-CHANNEL KEYLESS ENTRY SYSTEM Installation And Operation Manual MEGATRONIX VAN NUYS, CA U.S.A. CP634 1 REMOTE CONTROL CONVENIENT SYSTEM INSTALLATION & OPERATION INSTRUCTIONS INTRODUCTION

More information

3 Channel Remote Start / Keyless Entry System Installation Instructions

3 Channel Remote Start / Keyless Entry System Installation Instructions Model AA-RS5CS Installation Manual 3 Channel Remote Start / Keyless Entry System Installation Instructions This Unit Is Intended For Installation In Vehicles With 12 Volt Negative Ground Electrical Systems,

More information

Track Rocker Installation Instructions

Track Rocker Installation Instructions Track Rocker Installation Instructions Customizable Track Rocker Control System For Installing Painless Part Number: 58100 Track Rocker Relay Center Manual #90641 Painless Performance Products recommends

More information