2005 Hyundai Truck Santa Fe V6-3.5L

Size: px

Start display at page:

Download "2005 Hyundai Truck Santa Fe V6-3.5L"

Madison Dean
5 years ago
Views:

1 2005 Hyundai Truck Santa Fe V6-5L Vehicle» A L L Diagnostic Trouble Codes ( DTC )» Testing and Inspection» P Code Charts» P0320 DTC P0320 IGNITION/DISTRIBUTOR ENGINE SPEED INPUT CIRCUIT Component Location COMPONENT LOCATION GENERAL DESCRIPTION Ignition failure sensor is used to check whether the spark ignition is occurred correctly or not and also used to tachometer drive. The sensor monitors the voltage difference between a resistance which is on the battery circuit for ignition coil. When the ignition coil works properly, the electric current through the resistance is detected as voltage drop. This is confirmed for every ignition event with the crankshaft sensor and the camshaft sensor. If PCM detects a malfunction, no ignition is possible, so the engine would not start. If there is no ignition signal for a predetermined cycle for one or two ignition coils, an ignition coil circuit failure exists. DTC DESCRIPTION If there is no current at 3 ignition coils group during 32 ignitions, the PCM determines that a fault exists and a DTC is stored. DTC Detecting Condition

DTC DETECTING CONDITION Schematic Drawing SCHEMATIC DRAWING TERMINAL INSPECTION Many malfunctions in the electrical system are caused by poor harness and terminals.

2 DTC DETECTING CONDITION Schematic Drawing SCHEMATIC DRAWING TERMINAL INSPECTION Many malfunctions in the electrical system are caused by poor harness and terminals. Faults can also be caused by interference from other electrical Systems, and mechanical or chemical damage. Thoroughly check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration, or damage. Has a problem been found? YES: Repair as necessary and go to "Verification of Vehicle Repair" procedure. Go to " Power Circuit Inspection" procedure. POWER CIRCUIT INSPECTION

3 Check power to IG failure sensor Ignition "ON" & Engine "OFF" Measure voltage between terminal "4" of IG failure sensor harness connector and chassis ground. Specification: Approx. B+ 5. Is the measured voltage within specifications? YES: Go to "Ground Circuit Inspection" procedure. Check for open or short to ground in harness, repair as necessary and then go to "Verification of Vehicle Repair" procedure. GROUND CIRCUIT INSPECTION Check for open in harness

4 Measure resistance between terminal "1" of IG failure sensor harness connector and chassis ground. Specification: Approx. below 1 Ohm YES: Go to "Power Output Circuit Inspection" procedure. Check open in harness. Repair or replace as necessary and then, go to "Verification of Vehicle Repair" procedure. POWER OUTPUT CIRCUIT INSPECTION Check for open in harness Disconnect IG failure sensor connector and ignition coil connectors. Measure resistance between terminal "3" of IG failure sensor harness connector and "1" of each ignition coil harness connector. Specification: Approx. below 1 Ohm YES: Go to Signal Circuit Inspection procedure. Check open in harness between IG failure sensor and Ignition coil. Repair or replace as necessary and then, go to "Verification of Vehicle Repair" procedure. SIGNAL CIRCUIT INSPECTION

5 Check for short to ground in harness Measure resistance between terminal "2" of IG failure sensor harness connector and chassis ground Specification: Infinite YES: Go to "Check for short to battery in harness" as below. Check short to ground in signal harness. Repair or replace as necessary and then, go to Verification of Vehicle Repair" procedure. Check for short to battery in harness Measure resistance between terminals "2" and "4" of IG failure sensor harness connector. Measure resistance between terminals "2" and "3' of IG failure sensor harness connector.

6 Specification: Infinite 5. YES: Go to "Check for open in harness" as below. Check short to battery in signal harness. Repair or replace as necessary and then, go to " Verification of Vehicle Repair" procedure. Check for open in harness Disconnect IG failure sensor and PCM connector. Measure resistance between terminal "2" of IG failure sensor harness connector and terminal "3/121-B" of PCM harness connector. Specification: Approx. below 1 Ohm YES: Go to "Component Circuit Inspection " procedure. Check open in harness between IG failure sensor connector and PCM connector. Repair or replace as necessary and then, go to "Verification of Vehicle Repair" procedure. COMPONENT INSPECTION Check IG failure sensor Connect IG failure sensor and PCM connector. Engine "ON"

7 Check that RPM meter on instrument panel is operating correctly and the signal waveform of IG failure sensor at terminal Is the IG failure sensor normal? YES: Substitute with a known - good PCM and check for proper operation. If the problem is corrected, replace PCM and go to "Verification of Vehicle Repair procedure. Substitute with a known - good IG failure sensor and check for proper operation. If the problem is corrected, replace IG failure sensor and go to "Verification of Vehicle Repair" procedure. VERIFICATION OF VEHICLE REPAIR After a repair, it is essential to verify that the fault has been corrected. 5. Monitor and record the Freeze Frame Data for the Diagnostic Trouble Code(DTC) which has been diagnosed. Using a Scantool, Clear the DTCs. Operate the vehicle within conditions noted in the freeze frame data or enable conditions. Monitor that all readiness test have been verified as "Complete" Are any DTCs present? YES: Go to the applicable trouble shooting procedure. System is performing to specification at this time.

P0016. P0016 Crankshaft Position-Camshaft Position Correlation(Bank I Sensor A) Component Location

P0016. P0016 Crankshaft Position-Camshaft Position Correlation(Bank I Sensor A) Component Location 3/10/2018 P0016 (ALL Diagnostic Trouble Codes ( DTC )) - ALLDATA 2006 Kia Truck Sorento 2WD V6-3.5L Vehicle > ALL Diagnostic Trouble Codes ( DTC ) > Testing and Inspection > P Code Charts P0016 P0016 Crankshaft