Heating Plates for Fusing Plastics. Hand-held Spark Tester
|
|
- Ashley Hawkins
- 5 years ago
- Views:
Transcription
1 Heating Plates for Fusing Plastics TP 125 TP 200 TP 300 For fusing plastics (PE, PP, PVDF, PB, PVC), these manual heating plates are highly manageable because of their ergonomic handle. Can be supported either manually, with the fork-type stand (included) or with the optional bench vise. All have high quality Teflon (PTFE) plate coating and electronic controller for temperature adjustment. There are three models: TP125 for up to 3" diameter material, TP200 for up to 6" diameter and TP300 for up to 10" diameter material. Model TP 125 TP 200 TP 300 Working Range Ø 0-3" IPS - DIPS Ø 0-6" IPS - DIPS Ø 0-10" IPS - DIPS Power Supply 110 V 110 V 110 V Rated Power uptake 700 W 850 W 1300 W Operating Temperature 360 F F 360 F- 540 F 360 F- 450 F Overall dimensions 16" x 5½ x 2" 17" x 8½" x 2" 21½" x 12" x 2" Weight 4.5 lb 7 lb 11 lb Steel Case dimensions / weight 12" x 4" x 19" / 7 lb 12" x 4" x 22" / 8 lb 14" x 7" x 25" / 11 lb Pricing FOB FL Bench Vise Steel Case # A Hand-held Spark Tester High Frequency Generator for Testing Plastic Welds The model BD10AS is a hand-held unit which generates a high voltage at a high frequency. It is intended for intermittent use no more than 10 minutes at a time. It has an output between 20,000 to 45,000 volts at a frequency of approximately 500 khz. When properly adjusted and when the electrode is held within 1/4 to 1 inch from a metal object, a spark will jump to the metal. Current output of the spark is about 1 ma. Comes with standard tip electrode and uses same accessories as model BD50E. See BD50E for example of how defects in welds are detected. BD10AS HAnD-HelD SpArk TeSTer 307 FOB CA 22 Abbeon Cal, Inc. 123 Gray Ave. Santa Barbara, CA Catalog 115P
2 Spark Tester Defects are detected by electric current grounds through the defect Use bare wire or foil or any conductive material as backing Locate bad welds or pin holes easily! Fast! Convenient! Affordable! Coating/Lining Leak Detection Tank Lining Manufacturers Maintenance Departments Packaging Industries Neon Sign Industries Now you can check the quality of your weld. This rugged tester is specifically designed for inspecting tank linings and for applications where continuous use is a necessity. The unit s high voltage transformer isolates it from line power, so that it runs cooler. Input Requirement: Tester Output: Operating Time: Specifications 120V, 50/60 HZ Has isolation transformer 20,000-47,000 volts at frequencies of 1/2 megahertz Continuous in normal application Model BD50E SparkTester 637 FOB CA Accessory Electrodes Spring Tip T Tip. 41/4" wide for testing tank lining and other wide surfaces T Tip. Same as above, except 12-in. wide Fan Tip. Line voltage isolated steel spring wire fan for testing curved as well as straight linings and other surfaces Brass brush tip 4-in. wide for testing curved and straight lining and other surfaces Brass brush tip 8-in. wide for testing curved and flat surfaces. Hinged for hard to reach areas. 163 FOB IL peak VolTAge CAliBrATor 392 FOB IL For setting voltage by adjusting a calibrated spark gap. Enables voltage to be set accurately with repeatability, especially useful when using a generator to detect flaws in very thin coatings and in lab work. With NIST Traceable Certificate of Calibration Catalog 115P (800) fax: (805)
3 Ultrasonic Hand-Held Plastic Welders 20kHz 500 watts 120 volts (220V optional) These lightweight, yet rugged and reliable units are easy to operate and are designed specifically for welding, staking, inserting and spot welding applications. The hand held welders consist of an ultrasonic power supply and an ultrasonic hand held converter. The 20 khz hand held converter is supplied with a standard 1/2" (12.7mm) diameter flat-faced welding tip that attaches to an integral titanium front driver. This front driver has a 1/4-28 threaded end to accept other standard or custom tips. A variety of optional accessories, as well as standard threaded tips are available as described below. Digital Amplitude Control regulates the line voltage and provides constant amplitude throughout the welding process. Autotune Circuitry eliminates the need to retune the system each time it is tuned in or when the horn is changed. Programmable time or time and energy welding modes or continuous-duty mode. Backlit LCD Display. Ultrasonics Load Meter / Overload Protection Circuitry. Overload Reset. Ten-foot removable cable (other lengths available upon request). Staking/Spot Welding Tips Specifications Standard threaded tips available for staking, spot welding, and inserting are listed below. Special carbide coated wear resistant, flat, knurled, and custom faced tips are also available upon request. SPOT WELDING TIPS Material Thickness: TIP CODE Inches: MM LETTER 1/ SA 3/ SB 1/ SC 5/ SD 3/ SE 7/ SF Price FOB CT 65 each Tip Assortment Kit (20 khz only) This kit contains 6 spot welding tips, 6 staking tips, 6 overweight tips, 3 male knurled coarse tips, 3 male knurled fine tips, 3 inserting tips and 2 flat tips. Tips have 1/4-28 threaded stud and can be used on 1/2" diameter front drivers. Order No. - # STAKING TIPS - order by letter code TIP CODE LETTER Conical Boss Plastic Boss Solid Boss Flare Head 65 Spherical Head Hollow Diameter High Profile Low Profile High Low Boss Inches mm Tip Size Stud Height Tip Size Stud Height Profile Profile 1/ A.050 G.019 AA GG 1/ B.100 H.0375 BB HH 3/ C.150 I.056 CC II 1/ D.200 J.075 DD JJ R 5/ E.250 K.094 EE KK S 3/ F.300 L.112 FF LL T H520T-CV55 Time H520E-CV55 Time/ Energy FOB CT SpecificationS Model H520 (20 khz) Power Supplies Input Voltage: Standard 120 volts or optional 220 volts 50/60 Hz Regulated between volts or volts Dimensions: 8.5 in. H x 13.5 in. W x 7.5 in. D Weight: 13 lbs Model CV55 Hand Held Converters: Dimensions: 1.9 in. D, 7.6 in. L Weight: 1.5 lbs Horn: Titanium, Integral with threaded end to accept replaceable tips Tip: Standard 1/2" diameter flat faced titanium tip (see chart for other tip configurations) See accessories: Manual Press, Pistol Grip, Foot Pedal and a Video on our website Abbeon.com INSERTING SAE Inside Diameter Insert Size: of Insert Time only vs. Time/Energy Using a Time-Only Ultrasonic Welder, the pressure that is applied when you push down on the part with the welding horn is an uncontrolled variable that can lead to inconsistent welds. Using a Time/Energy Ultrasonic welder, you can select the energy option to control the pressure variable. The energy option measures the amount of energy transferred from the welder tip to the part for a consistent weld every time. Pilot Diameter of Tip 24 Abbeon Cal, Inc. 123 Gray Ave. Santa Barbara, CA Catalog 115P Price FOB CT METRIC Insert Size Inside Diameter of Insert Pilot Diameter of Tip Price FOB CT x x x x x / x / x /
4 ultrasonic handgun The TTHG2 ultrasonic handgun is ideal for spot welding plastic sheet and attaching non-woven materials using a variety of standard and application specific horns. This unit can be set to weld continuously or by time for repeatable and consistent welds. Two weeks lead time. STANDARD FEATURES Weld by time or continuous duty. Compact and portable power supply with overload protection. Lightweight handgun with pushbutton actuation. Accepts a wide range of standard and custom 40kHz horns. SPECIFICATIONS Power Requirements: 110 VAC 50/60Hz Cable Length: 6 Current full rated output: 2 amps Weld Time Setting: seconds Dimensions: 12 x10 x4.25 Output Frequency: 40kHz Weight: 13.5 lbs. Output Power: 150W OPTIONS Sturdy carrying case call for pricing. System available in 220V call for pricing. Choose form the array for a horn perfect for your application, by contacting us or visit our website Abbeon.com. hot Stapler Plastic repair kit Plastic repair has just taken a major step forward. The DF-800BR Hot Stapler Equipment helps save parts that would be difficult otherwise to save. This tool creates a strong, structural repair while still maintaining flexibility to allow for proper fitting of plastic components. The Hot Stapler uses heat to embed a staple into the plastic to stitch tears back together. Depending on the extent of damage to your plastic part, you can use the staples by themselves or to hold parts together for plastic welding to restore your part to original strength. Works on polyethylene and polypropylene only. Z-CLIP DF-800ZC Z-staple for stitching tears. Box/ Model TTHG2 Ultrasonic Handgun - 3,245 plus 325 to 450 Horn Price (FOB OH) Horns for Model TTHG2 See Abbeon.com for specs and pricing DF-400BR DF-800BR W-CLIP N-CLIP M-CLIP DF-800WC W-staple for corner gripping Box/ DF-800NC N-staple for large surfaces Box/ DF-800MC M-staple for outside corners Box/ V-CLIP S-CLIP U-CLIP DF-800VC V-staple for inside corners Box/ DF-800SC S-staple to stitch holes Box/ DF-800UC U-staple for rounded corners Box/ DF-800BR Deluxe Hot Stapler Kit comes with all 7 styles of clips (50 each), finishing iron, plastic rods & carry case Made in U.S. DF-400BR Basic Hot Stapler Kit comes with Z, M, V and S staples and has 3 heat settings Made in China fob Ca Catalog 115P (800) fax: (805)
5 Model TPHS400 Pneumatic Heat Staker 7,800 FOB OH Price does not include Tips or Holding Fixture OPTIONS manual heat Staker Ideal for R&D or production, the TTMS-400 is perfect for staking, swaging, inserting and degating. This compact and rugged bench-top unit has many features found in our pneumatic heat staker including digital temperature control and screw-in tip design. No compressed air just plug it in and go! Three to four week lead time. STANDARD FEATURES Digital temperature control with dwell with readout. Adjustable height, mechanical stop and threaded tip receiver. Base plate with threaded tool mounting pattern Pneumatic heat Staker When precise and repeatable staking, swaging, inserting, or degating are necessary, the model TTPS-400 is the one machine that can do it all. This rugged and versatile bench-top unit features an easy-to-use touch screen interface, screw-in tip design, and machined base with threaded fixture mounting holes for quick tool and job changes. Four weeks lead time. STANDARD FEATURES Digital temperature control with dwell and hold timers. Adjustable height, stroke speed, and dampener/positive stop. Touch screen interface, ergonomic dual button start with emergency stop. Threaded tip holder allows for multiple tip styles. SPECIFICATIONS Power Requirements: 120 VAC 50/60Hz Maximum force: psi Current full rated output: 15 amps Height Adjustment: 3.5 to 12 Pneumatic Requirements: Maximum Throat Depth: 6.5 Air cylinder: clean, dry psi Maximum Power: 400 Footprint: 13 x15 x35 Weight: 85 lbs. Multi-point platen call for pricing. Screw-in tips and tooling to suit your application available on request. Extended column height call for pricing. Automatic post cycle cooling call for pricing. Staking Swaging Insertion Degating Also referred to as heading or riveting, staking is the process of forming a plastic stud (boss) over another component to hold the two Swaging uses the controlled flow of molted plastic to capture or retain another component (usually of another material) in place. pieces together. When a regulated and controlled heat source contacts and transfers heat to a metal insert, it is called insertion. The insert is placed in a hole, either straight or tapered, in accordance with instructions from the insert manufacturer. TTHSTK weeks lead time TTHSWG weeks lead time TTHSNT weeks lead time TTHSDG 135 When a regulated and controlled heat source heats a metal blade that melts the plastic in the gate area and separates the runner from the molded part, it is called degating. See more information on Heat Staker/Spin Welder tips at Abbeon.com 2 weeks lead time SPECIFICATIONS Power Requirements: 120 VAC 50/60Hz Height Adjustment: 3.5 to 12 Current full rated output: 15 amps Maximum Power: 400 watts Current full rated output: 5 amps Stroke length: 4 (10.16cm) *Screw-in tips and tooling to suit your application available on request Model TMHS400 Manual Heat Staker 2,750 FOB OH Price does not include Tips or Holding Fixture 26 Abbeon Cal, Inc. 123 Gray Ave. Santa Barbara, CA Catalog 115P
6 Holds rolls securely. Moves them easily. Say goodbye to dollies, pallet jacks and sore backs. The On-A-Roll Lifter's sturdy steel construction lifts up to 880 lbs. and up to 16.4 feet wide. Nylon safety straps let one user pull rolls onto the securing tray for transport. Extended nylon straps provide leverage to help guide the roll into a specially designed high-walled transport tray and ensure material is secured for transfer. on-a-roll lifter The easy-to-use foot pump allows a user to raise the material with minimal effort. Heavy-duty 360 rotating casters make it possible to navigate through standard doors and narrow passages. Pushing awkward rolls around corners is no longer a concern. Works in the tightest shops with limited floor space. Deliver your rolls right up to the printer for efficient loading. Model Roll Weight Capacity 880 lbs 880 lbs 880 lbs Lift Height 33.5" 33.5" 33.5" Max. Roll Width 8' 2" 16' 4" 16' 4 Max. Roll Diameter 15.75" 15.75" 15.75" Width x Depth x Height 31.5" x 31.5" x 47" 47.25" x 31.5" x 47" 47.25" x 31.5" x 47" Weight 177 lbs 188 lbs 188 lbs Bottom Fork Clearance 4" 4" 3.5" Lifts Rolls up to: 8' 2" 16' 4" 16' 4" Price (fob PA) 1,595 1,595 1,595 Two-year warranty on all wheels, hydraulics and media tray. Five-year warranty on cross bars. 20 Watt Light Power Tech Mighty Lite 20 & 10 Watt Portable LED Rechargeable Work Light The most powerful battery powered lights on the market. A state of the art lithium ion battery system provides the brightest, most dependable and longlasting LED Work Light. 20 Watt Size: 7" X 5½" 10 Watt Size: 4½" X 3½" Item Number Watts Lumens Lighted Area (Square Feet) Battery Life (Hrs) Full Charge Time Lamp Life (Hrs) PT ,000 PT ,000 Price FOB CA Air Powered Router - 20,000 RPM Ideal for chamfers and roundover cuts on hardwoods, softwoods, solid surfaces or plastics. Great for laminate trimming, surface planning, beveling and cornering Front exhaust directs chips away from cutter Motor HP (W).7 (522) Motor RPM 20,000 Sound Level 85 db(a) Maximum Air Flow CFM/ SCFM (LPM) Hose I.D. Size Inch (mm) 5/34 (963) 3/8 (10) Air Inlet Thread 1/4" NPT Spindle Thread 3/8"-24 Male Weight Pound (kg) 2.5 (1.1) Base Size Inch (mm) 3¼ (83) x 3½ (89) Air Pressure 90 PSIG (6.2 Bar) Collet Depth 1-5/8" (41mm) Max. Cutter Dia. 1-1/8" (29mm) Height Inch (mm) 8¼ (210) Model FOB NY See specs on Abbeon.com Catalog 115P (800) fax: (805)
7 Aluminum Manifolds Features and Benefits One-piece extruded aluminum construction is lightweight with long-lasting durability. Quality anodizing protects the manifolds from corrosion and signifies Supply or Return. Different port size options provide connection flexibility. Brass end plug is included for customer convenience. Pre-drilled mounting holes make the manifolds ready to install. Optional ball valves and flowmeters provide instant flow, pressure, and temperature information, plus shut off individual supply and return lines. Single or parallel manifold configurations adapt to most mounting situations. Specifications Material Aluminum (6005-T6) Inlet Size 3 /4", 1", 1 /2" or 2" NPT (F) Each manifold includes: Port Size 1 /4", 3 /8", 1 /2" NPT female threads both ends Temperature Rating 300 F (149 C) One threaded brass end plug Maximum Working Pressure Ratings Specified number of NPT ports 150 psig (10 bar) When ordering please specify Anodized Color Blue (SUPPLY, add letter Z) or Red (RETURN, add letter Y) 3/4" Manifolds (1/4" Ports) 3/4" Manifolds (3/8" Ports) Total # Model Length FOB Ports Number MO With Ball Valve FOB Model Length FOB mm in. MO Number mm in. MO With Ball Valve FOB MO 4 6SA SA422B 115 6SA SA432B SA SA622B 160 6SA SA632B SA SA822B 205 6SA SA832B 246 1" Manifolds (1/4" Ports) 1" Manifolds (3/8" Ports) Total # Model Length FOB FOB Model Length FOB Ports Number mm in. MO With Ball Valve MO Number mm in. MO With Ball Valve FOB MO 4 SA SA422B 125 SA SA432B SA SA622B 172 SA SA632B SA SA822B 218 SA SA832B SA SA1022B 265 SA SA1032B SA SA1222B 312 SA SA1232B SA SA1622B 406 SA SA1632B /2" Manifolds (1/2" Ports) 2" Manifolds (1/2" Ports) Total # Model Length FOB Ports Number MO With Ball Valve FOB Total # Model Length FOB With Ball FOB mm in. MO Ports Number mm in. MO Valve MO 4 12SA SA442B A A44B SA SA642B A A64B SA SA842B A A84B SA SA1042B A A124B SA SA1242B A A164B SA SA1642B 566 US Patent Pending Other ports and configurations available please call or visit Abbeon.com. Quick Disconnect (optional) Turbulent Flow Range Flow Indicator Ring Laminar Flow Range Thumbwheel End Caps (brass or nylon) Temperature Gauge Turbulent Flow Indicator Diagnoses flow condition using FCI Technology This turbulent flow indicator has four scales built into the meter: three scales for turbulence and one scale for flow rate. Turbulent Flow Scales are selectable and correspond to cooling line inside diameter: 1/4", 3/8", or 1/2". Flow rate scale can be referenced quickly for additional functionality. See more information online at Abbeon.com To Order: 1. Add " B" at the end of the model # to indicate a standard thermometer or for a thermometer with quick-connect socket, and plug, add an " E" to the model # and 20 to the price. 2. Add " E" to model # for English (temp. in F and flow in GPM) or add " M" for metric (temp in C and flow in LPM). Brass End Caps Inlet Size Model Number Prices FOB MO 1/4" NPT(F) FC /4" BSPP(F) FC2B 133 3/8" NPT(F) FC /8" BSPP(F) FC3B 133 Nylon End Caps Inlet Size 1/4" NPT(F) FCP /4" BSPP(F) FCP2B 112 3/8" NPT(F) FCP /8" BSPP(F) FCP3B Abbeon Cal, Inc. 123 Gray Ave. Santa Barbara, CA Catalog 115P Laminar Flow Turbulent Flow
8 Mold Protective SwitcheS Global Thinswitch Liquid- Resistant (3mm/4mm Height) Operating Temp Switching Contacts: 80 C (176 F) max. SPST (normally open) BeCu with Hard Gold Plating For use with European standard molds. Global Thinswitch Limit Switch helps prevent accidental mold close in injection molds by verifying ejector plate return in injection molds with 3mm or 4mm rest buttons, and where occasional water or oil spray is present. A polyurethane dome covers the actuator spring, protecting internal gold switch contacts from environmental contamination. A special mounting bracket aids installation from the edge of the mold. The bracket allows molders to slide the Thinswitch into place without disassembling the mold or using screws to hold the switch in place. tw-222-lr 99 FOB MO Wt 0.2 lbs Versaswitch Limit Switch Optional mounting bracket shown Mold Protective Limit Switches are designed and built by engineers with expert moldbuilding experience. Thinswitch, SmartLock and Versaswitch are the benchmark switches in the injection molding industry. Molders rely on them to provide dependable position indication and protection for valuable injection molds. Thinswitch Limit Switch Thinswitch Limit Switch verifies ejector plate return in plastics injection molds. This small switch is thin enough to fit inside the ejector housing. It can also be used for core slides, or anyplace space is limited. Choose from the original design or T-222 Thinswitch Versaswitch Limit Switch installs into an injection mold to indicate location of the core, preventing tool damage. Versaswitch is easily installed into a 5/8"-24 female thread. The switch actuates when 3.5 lbs of force is applied to the plunger. Actuation height is adjusted by threading the switch to the correct position in the installation. The switch is held in place via a lockwasher and hex nut. SPDT snap action switch provides a simple, positive indication of the mold or core location. Optional mounting bracket is available to aid installation. Threaded fastener holes facilitate mounting the switch in many positions. The bracket is made from corrosion-resistant anodized aluminum. V-222 Versaswitch Includes lockwasher and nut VB-222 Mounting Bracket Red anodized aluminum All Prices FOB MO Original Thinswitch T F (79.4 C) max. 81 HT F (121 C) max. 93 Prices FOB MO Switches with.56"/14.2mm dia captive plunger 175 F (79.4 C) SL-222-CP max. 250 F (121 C) SL-291-CP max. the liquid-resistant housing for areas where water or oil spray is present.the Thinswitch Limit Switch has been tested for reliability over 10 million cycles without failure. Two switches can be used in series for larger molds. HT-291-LR Liquid-Resistant Thinswitch Liquid-Resistant Thinswitch T-222-LR 175 F (79.4 C) max. 111 HT-291-LR 250 F (121 C) max. 123 Prices FOB MO Slide Retainer & Limit Switch Smartlock Slide Retainer and Limit Switch provides switching and a slide detent in one unique package. The locking function prevents premature slide movement during molded part ejection while the SPDT switch is simultaneously actuated. The Smartlock has been tested for reliability over 10 million cycles without failure. Two or more switches SL-222-CP may be used for larger molds, or molds with multiple slides. Increased safety and prevention of mold damage result when the Smartlock slide retainer and limit switch is installed in a mold. A capture screw holds the plunger in the slide to prevent loss. Switches with.44"/11mm dia plunger (non-captive) SL F (79.4 C) max. 124 SL F (121 C) max. 135 All Prices FOB MO Catalog 115P (800) fax: (805)
9 Electronic Flowmeter With the Tracer electronic flowmeter, it is easier than ever to know exactly how much water is flowing through your water lines. In addition to flow rate, the Tracer provides a precise temperature reading of the water and will calculate BTU's. With the new information that the Tracer provides, you can manage your processes more completely and accurately. Flow Regulators 2" DDS-16B LCD Electronic Switching Flowmeter Smartflow flow regulators provide a unique, leak-free, single-point manual flow control. This regulator incorporates the proven mechanical flowmeter and integral needle valve in a compact design. Its very few moving parts improve reliability and leak-free operation. Used singly or in combination with a water manifold, the flow regulator allows manual Monitor each line or zone of your mold with Electronic Flowmeters control of individual cooling water lines. Brass valve, EPDM o-rings, and polysulfone viewing window are compatible with most process liquids. Optional temperature gauge may be added for additional process control information. Brass quick-connect fittings are available. See more information online at Abbeon.com See your flow rate per minute with Hot Oil Flowmeters Smartflow hot oil flowmeters are durable, vane-operated devices that provide visual indication of flow rate in gallons per minute. The indicator ball is separated from the process by a high temperature gasket and stainless steel plate. A glass window retains the indicator ball. This flowmeter is designed specifically for hot oil circulating loops in industrial processes. Compact size works well in restricted-space locations. Rugged construction provides years of dependable service. 550 F (288 C) Temperature Rating allows installation into hot oil applications. Economical for use in many locations throughout the plant. Line mounted for easy installation without extra brackets or hardware. 40 gallons/minute Dimensions Wetted Parts and Materials Inlet Size... 1" NPT(F) Body...Carbon Steel (black oxide finish) Viewing Window... Glass Vane...Stainless Steel Spring...Stainless Steel Pin...Stainless Steel Gasket...Non-Asbestos Fiber Magnet... Sintered Alnico 8HE Specifications Operating Temperature F max. (288 C max.) Operating Pressure psi max. Accuracy... ±10% Model # FOB MO HF8A40 Hot Oil Flowmeter 4.75" x 2.25" x 2.25" HF8B40 Hot Oil Flowmeter 4.75" x 2.25" x 2.25" with Temperature Gauge HF4A60 Hot Oil/ water flowmeter 3.75" x 1.5" x 1.5" HF4B60 Hot Oil/water flowmeter 3.75" x 1.5" x 1.5" with Temperature Gauge Abbeon Cal, Inc. 123 Gray Ave. Santa Barbara, CA Catalog 115P
10 FasTie Quick Ejector Tie-In System Description & Use In an injection molding press, the FASTIE system quickly ties in the mold ejector plate to the press ejection system, dramatically reducing mold change time. The greatest time savings are realized in presses where space is limited and the ejector system is difficult to tie in using solid knock-out bars. The FasTie coupler may be permanently mounted to the press ejector plate. The quick-connect locking mechanism in the coupler snaps mechanically onto the mold-mounted stud during mold installation. 2-Inch 1 3 /8-Inch 1-Inch High Strength FasTie Couplers FasTie Studs To release the ejectors, apply shop air to the coupler. The coupler opens to release the stud, disconnecting the press and tooling ejector plates. The coupler remains in the open position, ready for a new mold to be set. For multiple ejector locations, an air manifold is recommended to release all couplers simultaneously. Three FasTie models are available: 1-inch original model for presses 500 tons and under, 1-inch High Strength FasTie for center knockout and high speed ejection, and 2-inch model for presses larger than 500 tons. Typical Application for 2 or 4 Ejector Positions Couplers are located at the end of the ejector bars mounted to the press ejector plate. Studs are mounted to each mold in storage. Ejector connection is made without changing ejector bars. Ejector housing shown is 1.062" thick. Air Manifold supplies compressed air to the end of each ejector bar for simultaneous coupler release. Fixed length bars are finished on site, cut to length and tapped with 1/2-13 female thread. Features & Benefits FasTie installs easily into existing tapped holes, no additional machining is required. FasTie reduces mold setting time by quickly uncoupling, plus there are no loose parts to stow. FasTie remains coupled during mold cycling for increased tie-in reliability and reduced wear. SpeedBar adjustable ejector bar changes length quickly without tools [±1/2"(12.7mm) from nominal in.006"(.15mm) increments.* SpeedBar saves molders time and cost of machining individual ejector bars to fit different molds.* * 1-inch only This setup is designed for captive molders, or shops with tools using a standard thickness ejector housing. For determination of length, installation examples, specifications, accessories and pricing, see our website or use your phone to scan our QR code. Abbeon.com Catalog 115P (800) fax: (805)
11 Digital Melting Point Meter The Model 333 Digital Melting Point Meter is designed to measure the melting point for testing plastics, waxes, resins, inks, gums, fats, tars, low melting point alloys, organic and inorganic compounds, and many other substances. This instrument operates over dual scale ranges of 120 F to 500 F and 50 C to 260 C along the platen bar. Use on any convenient workbench or stand. Plug into 120 volts AC, Hz and flip the toggle switch to the on position. The stainless steel platen will then heat up on a precisely designed temperature gradient spanning nearly 400 F across the length of the platen. The method of operation is fast and only a small quantity (a few milligrams) of the test substance is needed. With simple precautions, samples can be recovered uncontaminated. Place a sample of the substance to be checked along the upper surface of the platen. The demarcation line between the molten and solid particles of the substance will quickly be seen. specifications Dual Range 120 o F to 500 o F or 50 o C to 260 o C Accuracy ±2% of full scale range Dimensions 19¾"L x 6"W x 7¾"H Weight 9½ lbs Shipping Weight 14 lbs. (6.4kg) Power source 120V AC : LCD Digital Display Model 333 Digital Melting Point Meter (selectable F or C) 110 VAC Model 334 Digital Melting Point Meter (selectable F or C) 220 VAC FOB CA Polariscope with Tint Plate A polariscope is an essential tool for detecting strains in transparent materials. It can be used to monitor production items or to inspect incoming materials. The Model 243 is also very useful in production or in the laboratory for checking welds, bends, castings, or degree of annealing. The unit features a 6" diameter viewing area with a rotatable polarizer and a full wave retarder tint plate. The light source is provided by two 15-watt bulbs, 120V AC or DC is required. See our website Abbeon.com for more details Model 243 Polariscope 855 FOB CA The Kit Includes: 1 Calibration Certificate 1 Main Unit 1 Probe 5PΦ10 2 x 1.5V Batteries 1 Instruction Manual 1 Carrying Case 1 Bottle of Coupling Paste Ultrasonic thickness GaUGe tt100 kit Handheld portable ultrasonic thickness gauges can measure any work piece that has two parallel surfaces and made of a material that allows ultrasound waves to travel through. Most people use units with a standard 5MHz probe because it covers a wide thickness range. Some people would need a 7MHz probe if they are testing really thin parts. A few people would need 2.5MHz probe for work pieces with rough surfaces and thick walls. Ultrasonic thickness gauges work best on clean surfaces. Optional probes: Probes Frequency TT100 Ultrasonic Thickness Gauge See Abbeon.com for specifications Measuring range(steel) Min area Φ Min pipe size Characteristic 514 TT5P10 5 MHz mm 12mm Φ20x3mm Standard Straight 95 TT5P MHz mm 12mm Φ20x4mm Optional 90 Head 95 TTSZ25P 2.5 MHz 3-300mm 14mm ~ Thick Surface/ Rough Surface TT7P6 7 MHz mm 7.5mm Φ15x2mm Thin Material 95 FOB NJ Abbeon Cal, Inc. 123 Gray Ave. Santa Barbara, CA Catalog 115P
ReguLATOR. Your Platform for Scientific Cooling SM. from. ELTA-Q Precision Flow Regulator. General Description. Features and Benefits
from precision FLOW ReguLATOR Your Platform for Scientific Cooling SM ELTA-Q Precision Flow Regulator U.S. Patent Pending General Description Delta-Q is a low-cost precision flow regulator module that
More informationflow regulators Why use smartflow Flow Regulators?
flow regulators Why use smartflow Flow Regulators? Create Repeatable and Balanced Processes Multiple circuits within an injection mold often have different cooling requirements. Cooling water will normally
More informationSmartflow Fluid Control, Ejector Couplings and Mould Safety. Cool, connect and protect your mould with Smartflow
Cool, connect and protect your mould with Smartflow Aluminium Manifolds High quality and manufactured to exacting standards. One piece extrusion and anodized for corrosion protection. Predrilled for easy
More information- Quick ejector Tie-in system
- Quick ejector Tie-in system 3-Inch 2-Inch 1 3 8-Inch 1-Inch High Strength FasTie s U.S. Patent No. 6,379,072 FasTie s Description & Use In an injection molding press, the FasTie system quickly tiesin
More informationAbbeon Cal, Inc. Model BD-50E HIGH FREQUENCY GENERATOR OPERATING MANUAL
Abbeon Cal, Inc. Model BD-50E HIGH FREQUENCY GENERATOR OPERATING MANUAL DESCRIPTION. The Model BD-50E is a rugged tester designed for testing tank lining and other applications where extended use is necessary.
More information12 Months 12 Mon. + Yr Years Blank A C D E L N
Date Stamp Mat.: INOX. 1.4034 - Hard. 51 ± 3 HRC Maximum working temperature 150 C. Patented System Inner insert is always at the same level as the body of the date stamp. Wide range of diameters. Only
More informationThermo Scientific Gilmont
Direct Reading Laboratory Flowmeters Instruments Wide selection of flow ranges measure air from 0.02 ml/min to 137 LPM or water from 0.0002 ml/min to 4.1 LPM Excellent chemical compatibility with glass
More informationSimplifying Inspection MAGNETIC PARTICLE TESTING ACCESSORIES
MAGNETIC PARTICLE TESTING ACCESSORIES MPI Accessories 7 Magnaflux 7 Magnetic Particle Testing Accessories are designed to help improve the speed, detection capabilites, and cost effectiveness of your MPI
More informationG2 Industrial Grade Meters
G2 Industrial Grade Meters The unique modular approach of the Industrial Grade Meter line allows you to section 2: g2 industrial grade meters design a meter to match your specific application. Turbine
More informationTooling Supplies. Polishing
Tooling Supplies Section ontents A Air File... 299 B Ball Point Metal Markers... 287 Bolts Eye Bolts... 294 Shoulder Bolts... 292 Stripper Bolts... 292 arbide Burr Sets... 02 arbide Burrs...01 02 D Diamond
More informationRosemount 8750WA Magnetic Flowmeter System For Water and Wastewater Industries
Product Data Sheet January 214 813-1-475, Rev FA Rosemount 875WA Magnetic Flowmeter System For Water and Wastewater Industries THE 875WA MAGNETIC FLOWMETER Rosemount reliability in a customized offering
More informationLab Specialty Products Technical Information TECHNICAL INFORMATION WEIGHTS & DIMENSIONS
Lab Specialty Products Technical Information TECHNICL INFORMTION WEIGHTS & DIMENSIONS Contact Spears for any Information not found. Page 569 Lab Ball s Sample Engineering Specification ll thermoplastic
More informationDistributed By: M&M Control Service, Inc Product Product Code Technical Instructions Page #
Table of Contents Product Product Code Technical Instructions Page # Pneumatic Air Station Equipment 201/656/908 155-005/049/086/137P25 H-3 Pressure Gauges GA142AP 155-025P25 H-7 External Restrictors 184
More informationFluid Dispensing Systems
Fluid Dispensing Systems Automotive Commercial Industrial Diesel Exhaust Fluid (DEF) Open Systems Drum and Tote Packages Lever Pump System EPDM seals for maximum chemical compatibility. Includes 1300-028
More informationSpecial Applications Require Special Tools
Index Routers.................. 102-103 Tappers..................... 104 Clinch Nut Tools.............. 106 Rivet Shavers................ 107 Skin Clamp Runners........... 108 Saws................... 109-110
More informationSimplifying Inspection MAGNETIC PARTICLE TESTING ACCESSORIES
MPI Accessories 7 Magnaflux 7 Magnetic Particle Testing Accessories are designed to help improve the speed, detection capabilites, and cost effectiveness of your MPI system. Simplifying Inspection 48 CABLES,
More informationISTEC MAGNETIC METERS
ISTEC MAGNETIC METERS MEASURE ANY CONDUCTIVE LIQUIDS OR SLURRIES (EVEN ABRASIVE OR CORROSIVE) WITH THE NEW MICROPROCESSOR-BASED MAGNETIC METER -- A QUALITY PRODUCT - SIMPLE - RELIABLE - AT AN AFFORDABLE
More informationPosition Control Hard chrome-plated carbon steel piston rod with blackened threads and wrench flats Sintered bronze rod bushing Internally lubricated
Position Control System Products Cylinders 7.3-7.9 Cylinder Rod Lock 7.10-7.11 Cylinder Accessories 7.12-7.15 Pneu-Turn 7.16-7.24 Position Control System 7.25-7.36 Digital Panel Meter 7.37-7.42 Electronic
More informationW91/W94 Series TEMPERATURE REGULATORS. Self-Operated Temperature Regulators. Design & Operation W91 Non-Indicating W94 Dial Thermometer
Design & Operation W91 Non-Indicating W94 Dial Thermometer Watson McDaniel reserves the right to change the designs and/or materials of its products without notice. 2010 Watson McDaniel Company CAPILLARY
More informationPenetration. Test Methods
Test Methods Penetration of Bituminous Materials ASTM D5; IP 49; DIN 52010 Cone Penetration of Lubricating Grease ASTM D217; IP 50; ISO 2137; DIN 51804; FTM 791-311, FTM 791-313 Cone Penetration of Petrolatum
More informationSquare HeadTM Concrete Vibrators. wycotool.com
Square HeadTM Concrete Vibrators TM wycotool.com TM Electric Square Head Concrete Vibrators Performance and Productivity End cap protects switch Heavy-duty protective frame Radial fan - motor runs cooler,
More informationA1 SERIES COMMERCIAL GRADE METERS A1 SERIES COMMERCIAL GRADE METERS
COMMERCIAL GRADE METERS Look for the silver label! Look for the silver label! COMMERCIAL GRADE METERS Commercial Grade Meters are designed as self-contained, battery powered units. These indicating meters
More informationGREASE GUNS SECTION TWO. Battery Powered Grease Guns
Battery Powered Grease Guns and Accessories Professional Series Heavy Duty Series High Pressure Series Specialty Series Standard Duty Series Grease 1-866-4-ALEMITE Gun (866-425-3648) Accessories Alemite
More informationModel. Reach into areas as small as 3/8". Model. Max. Air Flow SCFM (L/Min)
The Dynafile Original The Best Tracking Abrasive Belt Tool in the World! 14000 For 24" Long Belts World-famous Dynafile replaces tedious hand filing and sanding. Grind, deburr, blend, polish, finish and
More informationdial Bore gauge set deck Bridges 6'' stainless steel Calipers rocker stud remover 6'' digital Calipers top dead Center stop
415 dial Bore gauge set Used for checking cylinder bores, but is also useful for checking connecting rod bores for size, straightness or taper. Accurate to.0005. 15052 Dial Bore Gauge Set deck Bridges
More informationDynafile...8 Dynafile II hp Dynafile II...12 Vacuum Dynafile II...13 Electric Dynafile II...13 Mini-Dynafile II...16
Dynafile...8 Dynafile II...11.4 hp Dynafile II...12 Vacuum Dynafile II...13 Electric Dynafile II...13 Mini-Dynafile II...16 Dynafile III...18 Dynabelter...22 Dynangle...25 Dynangle II...26 Take-About Sander...27
More informationSanders, Buffers & Polishers Introduction
Sanders, Buffers & Polishers Introduction Dotco sanders, buffers and polishers are available in a variety of styles and power ratings to provide flexibility in choosing the best tool for the job. Disc
More informationA1 Commercial Grade Meters
A1 Commercial Grade Meters Commercial Grade Meters are designed as self-contained, battery powered units. These indicating meters come in Aluminum or Nylon only. A1 Meters are not field serviceable like
More informationTable of Contents. Page. See Catalog and Product Updates on our Website
2 Table of Contents Page Sapphire Orifice Assemblies... 3-5 Metal Orifice Assemblies - Barb Connections... 6-7 Metal Orifice Assemblies - NPT Connections... 8-9 Metal Orifice Assemblies - Inserts... 10-13
More informationS P R AY E R VA L V E S AND C O N T ROL S C AT A L OG
Q UA L I T Y VA LV E S A N D C O N T R O L S. TO D AY A N D TO M O R R O W. Texas Industrial Remcor, Inc. CATALOG NO. 33 The new RC2 control system: Ensures no potential leaks in the tractor cab when using
More informationMODEL 905V OPERATING INSTRUCTIONS
MODEL 905V OPERATING INSTRUCTIONS Quantek Instruments 183 Magill Drive Grafton, MA 01519 Tel: (508) 839-3940 Fax: (508) 819-3444 Email: sales@quantekinstruments.com GENERAL DESCRIPTION These instructions
More informationDELTA4000 Accessories
DELTA4000 Accessories TESTING LARGE SPECIMENS Resonating Inductor The resonating inductor expands the capacitance range of the DELTA automated insulation power factor test sets. The resonating inductor
More informationHIGH PRESSURE HYDRAULICS PUMPS CYLINDERS JACKS
HIGH PRESSURE HYDRAULICS PUMPS CYLINDERS JACKS Since 2001, PowerX International, LLC has been collaborating with its customers to design and supply hydraulic products and systems. Specializing in mobile
More informationA1 Commercial Grade Meters
A1 Commercial Grade Meters Commercial Grade Meters are designed as self-contained, battery powered units. These indicating meters come in Aluminum or Nylon only. A1 Meters are not field serviceable like
More informationIN-LINE HYDRAULIC FLOW TESTER
SPX Corporation 5885 11th Street Rockford, IL 61109-3699 USA Internet Address: http://www.powerteam.com Tech. Services: (800) 477-8326 Fax: (800) 765-8326 Order Entry: (800) 541-1418 Fax: (800) 288-7031
More informationSmartflow FasTie Quick-Connect Ejector Tie-In System
Smartflow FasTie Quick-Connect Tie-In System 1"HS, 1-3/8", 2" & 3" Components, Installation Instructions US Patent No. 6,379,072 General FasTie Quick-Connect System ties-in the mold ejector plate to the
More informationMovotec Drives > Folding Hand Cranks (small and large)
Movotec Drives > Folding Hand Cranks (small and large) Can be mounted right-at-hand, yet folds completely out of the way when not in use. The small crank has a 100 mm radius and is intended for lifting
More informationHelping you get the job done right the first time! Dependable Lightweight- Easy to use 12 volt Groundwater pumps.
Helping you get the job done right the first time! Dependable Lightweight- Easy to use 12 volt Groundwater pumps. Building on over 18 years in business, Proactive Environmental Products understands your
More informationHousing Styles. Square Aluminum Block
Page 1 of 18 Housing Styles Square Aluminum Block AB General purpose temperature Accomodate a variety of elements Type A B Customize AB1 0.187" 0.75" AB2 0.250" 0.75" AB3 0.250" 1.25" AS Square Aluminum
More informationPERFORMANCE DATA. The lightweight, durable, low-profile ROD CYLINDER SLIDES
The lightweight, durable, low-profile H-Block design is the most versatile of our rod cylinder slides. It also has one of the highest ratings of load weight vs extension for its kind in the industry. The
More informationPOWER Pneumatic, Hydraulic, & Electric
POWER Pneumatic, Hydraulic, & Electric Pneumatic straight and right angle 6B spline drive motors Powerful HPU-20 with standard remote control pendant Eibenstock HD available with or without remote control
More informationTEMPERATURE REGULATORS W91/W94 Series
Self-Operated Temperature Regulators Watson McDaniel reserves the right to change the designs and/or materials of its products without notice. 2010 Watson McDaniel Company Self-Operating Design Indicating
More informationSTORAGE & MATERIAL HANDLING
www.greenlee.com STORAGE & MATERIAL HANDLING Contractors the world over rely on Greenlee storage and material handling solutions to keep product safe. From small chests to large field offices, and now
More informationSTRESSTECH CAPABILITIES
STRESSTECH CAPABILITIES M A C T E C H H E A T T R E A T I N G S O L U T I O N S HEAT TREATING A Division of Mactech STRESS RELIEVING CONSOLES STRESSTECH manufactures three portable stress relieving consoles
More informationLiquid Strainers. Protect nozzles, valves and pumps from damaging debris. Experts in Spray Technology Spray Nozzles. Spray Fabrication.
Experts in Technology Nozzles Control Analysis Fabrication Liquid Strainers Protect nozzles, valves and pumps from damaging debris. Table of Contents T Strainers Low to Medium Pressure TW...3 TWC...3 TWF...4
More information3/8-Inch Torque Wrench Square Drive, Torque Range Of 30 to 250 Inch Pound (3.39 to NM)
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 57005 3/8" Torque Wrench Square Drive Klein Tools Catalog Number 57005 Manufacturer Klein Tools 3/8-Inch Torque Wrench
More informationKNOCK CYLINDERS CONTENTS ACTUATORS GENERAL CATALOG. Caution KNOCK CYLINDERS
CAD drawing data catalog is available. ACTUATORS GENERAL CATALOG CONTENTS Features/Introductions of Variations 79 Double Acting Type Specifications 81 Order s 82 Inner Construction and Major Parts 83 Dimensions
More informationPistol Grease Guns. AC475 comes complete with 4" steel extension and 4-jaw coupler with ball check AC476 comes complete with 18" flexible
Lubricating Mini Pistol Grease Guns Deluxe Single-hand-operated pistol grip Die cast grease gun head with dual discharge ports for use with steel extension as well as flexible hose Develops 3500 PSI Capacity:
More informationMinimally protruding jaw shank for greater capacity in tight spaces.
Klein s line of wrenches are forged from the finest steel and are designed to deliver great strength and long working life. Regardless of the job type, Klein has a wrench that will help the professional
More informationPressure Controller. Cataloge K Code Characteristics Index. K00-2 Pressure Controller Brief Introduction
K Pressure Controller Cataloge Code Characteristics Index K00-2 Pressure Controller Brief Introduction KC32 Screw Tube Differential Pressure Controller K01 KY10 Bellows Type Differential Pressure Controller
More informationHVAC PLUMBING TOOLS CATALOG 2019 F-1. PIPE cutters. Excellent for cutting tubing insulation Strong nylon handle
hand tools PIPE cutters Excellent for cutting tubing insulation Strong nylon handle Ratchet action 1-5/8-Inch capacity Heat treated blade 36101 Little Tubing Cutter EA 10 36102 2 Replacement Blades PK
More informationGeneral Engineering Spray Nozzles & Accessories
General Engineering Spray Nozzles & Accessories 3 GENERAL SPRAY NOZZLES & ACCESSORIES Clip On Spray Nozzles SWIVELING ANGLE ADJUSTMENT SPRAY CHARACTERISTICS : These nozzles simply clip over a pre-drilled
More informationLinear Thrusters/PneuMoment
/PneuMoment Extruded TE Series 3.3-3.10 3.11-3.16 T Series Multiple Position T4 Series Movable Housing 3.17-3.22 3.23-3.24 3.25-3.28 3.29-3.32 Pneu-Moment Checklist PneuMoment Pneumatic Actuators PneuMoment
More informationFord Service Saddles and Tapping Sleeves
DQS Inc. Section AA 09/2017 THE FORD METER BOX COMPANY, INC. CERTIFIED TO ISO 9001:2015 10004466 Ford Service Saddles and Tapping Sleeves Contents Recommended Product Application *Steel *C900/909*** Cast
More informationG2 SERIES INDUSTRIAL GRADE METERS
Industrial Grade Meters INDUSTRIAL GRADE METERS The unique modular approach of the Industrial Grade Meter line allows you to design a meter to match your specific application. Turbine choice depends on
More informationControl & Power, Inc
Way/ 2 and 3 Position Four ported valves are generally used to operate double-acting cylinders or actuators. They have four or five pipe connections, commonly called ports: One pressure inlet. Two cylinder
More informationPressure Instrument Testing Equipment
Pressure Instrument Testing Equipment BULLETIN TE-1 A Halliburton Company A Durable, Portable Primary Standard Model 1305D Deadweight Tester The Ashcroft 1305D Deadweight Tester is an affordable, portable
More information1/2 Air Impact Wrench P/N IR 2235TiMAX-2 With 2 Anvil, Weighs Only 4.9 lbs ft.-lbs. torque. 3/4 Super Duty P/N IR 261
37 Order NLINE www.midwestwheel.com CATALOG NUMBER Ingersoll Rand Air Tools & Accessories 3/8 Air Impactool IR 2115TiMAX The best power-to-weight ratio in its class 300 ft.-lbs. torque Enhanced power settings
More informationCAPACITOR DISCHARGE STUD WELDING SYSTEMS
CAPACITOR DISCHARGE STUD WELDING SYSTEMS ARE complete stud welding systems which weld CD studs using the CD stud welding process. CONSIST OF the following items: A CD stud welding Power Supply/Controller
More informationCorrosion Resistant and Ultra-Pure Rotameters for Accurate Measurement of Liquids and Gases
Corrosion Resistant and Ultra-Pure Rotameters for Accurate Measurement of Liquids and Gases Rotameters Markets/Applications George Fischer rotameters are ideally suited for a multitude of corrosive and
More informationABRASIVE BELT TOOLS. APTOOL.RU Phone: +7 (495)
ABRASIVE BELT TOOLS APTOOL.RU Phone: +7 (495) 723-19-55 ABRASIVE BELT TOOLS The Dynafile Original Air-Powered Abrasive Belt Tool The Best Tracking Abrasive Belt Tool in the World! 14000 For 24" Long Belts
More informationM Series. Feature rich flow meter and switch with in-line. flow
Features Wide flow rangeability Outstanding accuracy State-of-the-art electronics - high reliability 4-20 ma, 0-10 VDC, or pulse output Visual indication Adjustable flow switch - built in Small footprint
More informationM-8100EP. Installation Guide ENGINEERED PLASTIC MANIFOLD SERIES. Introduction. A. Assemble Manifold Components
Introduction The Pro Manifolds with Integrated adaptor are designed for use in Hydronic radiant panel heating and cooling applications. They are available in various sizes, configurations, and options
More informationAuxiliary Equipment. Table of Contents. Auxiliary Equipment H-1. Product Product Code Technical Instructions Page #
Table of Contents Product Product Code Technical Instructions Page # Pneumatic Air Station Equipment 201/656/908 155-005/049/086/137P25 H-3 Pressure Gauges GA142AP 155-025P25 H-7 External Restrictors 184
More informationMF-12A MF-12A OWNER S MANUAL MF-12A PINSPOTTER MACHINERY DIVISION
MF-12A MF-12A PINSPOTTER MF-12A MACHINERY DIVISION OWNER S MANUAL ELECTRICAL REQUIREMENTS Connect the MF-12A to a 60 amp power supply. (208-230 volts 60 cycle). The MF-12A uses 208 230 volt single phase.
More informationNon-Spill, High Flow, Polypropylene Quick Disconnect Couplings
Non-Spill, High Flow, Polypropylene Quick Disconnect Couplings U.S. Patent 4703957, others pending. CPC s patent-pending NS4 Series quick disconnect couplings feature non-spill valves in a compact size,
More informationValves, Fittings, and Manifolds Catalog. We make things MOVE
Valves, Fittings, and Manifolds Catalog We make things MOVE We Make Things Move A forward-thinking innovator, Bimba provides industry-leading pneumatic, hydraulic and electric motion solutions that are
More informationQuicklub Lubrication Systems
Fittings, Adapters and Accessories Divider Valve Mounting Accessories 246416 Valve mounting bracket 51304 ¼" nylon locknut for valve mounting 247023 Grade 8, ¼" valve mounting bolt 239499 Template for
More information2 0 1 7 D E F E Q U I P M E N T C ATA L O G 608-487-9770 www.hartlandlubes.com TD1 Features & Benefits: Great performance and quiet operation Self priming Stainless steel motor shaft Polypropylene housing
More informationMANUFACTURER S MANUFACTURER, INC.
MADE IN THE USA MANUFACTURER S MANUFACTURER, INC. Manufacturer s Manufacturer, Inc. Lancaster, CA P r o fe s s i o n a l Pa i n t E q u i p m e n t B o d y E q u i p m e n t S t o r a g e S o l u t i o
More informationFunction Fittings. Flow Control Regulators. Piloted Function Fittings. Non-Return Valves. LIQUIfit Pressure Fittings. Other Function Fittings
Flow Control Regulators Piloted Non-Return Valves LIQUIfit Pressure Fittings Other Silencers Flow Control Regulators (P. 4-6) Blocking Fittings (P. 4-36) Piloted Non-Return Valves (P. 4-38) Function:
More informationRoll Grooving ROLL GROOVING. Pipe Capacity. No. of Models. Type. Page
Roll Grooving Designed to improve speed and efficiency for fire sprinkler and other industrial installations. Wide selection of mechanical and hydraulic units for applications up to 24" in diameter. Type
More informationMeeting the needs of automotive customers and MRO organizations, no toolbox is complete without an assortment of specialty items. Blackhawk by Proto
Specialty tools Meeting the needs of automotive customers and MRO organizations, no toolbox is complete without an assortment of specialty items. Blackhawk by Proto includes popular puller configurations,
More informationTOYOTA SIENNA TRAILER WIRE HARNESS Preparation
Preparation Part Number: PT791-08150 (non-se) PT791-08102 (SE only) Kit Contents Item # Quantity Reqd. Description 1 1 Trailer Module Harness 2 1 4-Flat Harness 3 1 Battery Power Wire Harness 4 1 Mounting
More informationStandard Knockout Punches 10. Punch Kits for Hydraulic Drivers 11. Draw Stud Selection Guide 13, 14, 18. Special Shape Punches
8 Punching Tools, Hole Saws, Step Bits Page Punching Tools Standard Knockout Punches 10 Slug Buster Knockout Punches 10 Slug Splitter Knockout Punches 10, 12 Punch Kits for Hydraulic Drivers 11 Draw Stud
More informationCOLOR CODED, QUICK-CHANGE ALUMINUM MANIFOLDS Full flow for optimum cooling
Page 258 COLOR CODED, QUICK-CHNGE LUMINUM MNIFOLDS Full flow for optimum cooling Pre-plumbed molds reduce set-up time, eliminate connection errors Low profile Can be equipped with quickchange connectors
More informationDesign and Application Details
Model 400 OVENPAK Gas Page 2105 Design and Application Details OVENPAK s are nozzle-mixing gas burners for many industrial direct-fired applications where clean combustion and high turndown are required.
More informationPower Features. Integrated Welder For Ultrasonic Plastics Assembly. more. Models XPT and XPE. for more information:
more Power Features new FEATURES Digital Time and/or Constant Energy Weld Modes Available Single-piece Rigid Cast Aluminum Machine Base and Column Hub Digital Amplitude Control Ultrasonic Horn/Stack Frequency
More informationPRODUCT GUIDE & MASTER PRICE LIST
2012 PRODUCT GUIDE & MASTER PRICE LIST deep cuts square corners TIGHT SPACES About ICS Prior to 1990, Diamond Chain Technology and concrete cutting chain saws simply didn't exist. Introduce ICS and twenty
More informationP O W E R P U M P S SECTION INDEX. Proper Size & Selection G1 Series Electric...
SECTION INDEX Proper Size & Selection... 44-45 G1 Series Electric... 46-47 2 Series Electric... 48-49 G3 Series Electric... 5-51 G4 Series Electric... 52-53 P O W E R P U M P S G5 Series Electric... 54-55
More informationWRANGLER 2016 WHEEL DRIVE, PAD ASSIST & ELECTRIC MODELS
WRANGLER 2016 WHEEL DRIVE, PAD ASSIST & ELECTRIC MODELS BRUSH LIFT 101 9121960 3/8 EXTERNAL STAR LOCK WASHER 1 102 9122030 3/8-16 X 3/4 BUTTON HEAD SOCKET SCREW 1 103 2694261 CABLE 1 104 2391771 90 HOSE
More informationFLOW CONTROL VALVES & ACCESSORIES
TECHNICAL SPECIFICATIONS construction Valve group Materials Mounting Ports Position Operating temperature PNEUMATIC DATA Operating pressure Nominal pressure nominal flow needle-type Meter In, Meter Out,
More information% ^ ) 4/2 SERIES. Direct Mount. Direct Acting Direct Mount Pilot Valves. Brass or Stainless Steel Bodies 1/4" NPT. Features. Construction.
Direct Acting Direct Mount Pilot Valves Brass or Stainless Steel Bodies /" NPT / 83 Direct Mount Features NAMUR direct mount version of the rugged, dependable 83 Series valves Direct acting, high flow
More informationQB4 PRESSURE CONTROL VALVE INSTALLATION & MAINTENANCE INSTRUCTIONS
QB4 PRESSURE CONTROL VALVE INSTALLATION & MAINTENANCE INSTRUCTIONS DESCRIPTION The QB4 is a closed loop electronic pressure regulator consisting of two solenoid valves, an internal pressure transducer,
More informationLUBRICATION & FLUID HANDLING ACCESSORIES. Heavy duty knurled steel barrel with large threads for easy loading.
hand grease guns Lever type The tough high pressure cast iron head makes Pro-Master Grease Guns unique in comparison to common pot metal or other die cast heads with a head burst pressure of 17,000 PSI
More informationElectronic Control Valves
MODEL 131 Series (Full Internal Port) 631 Series (Reduced Internal Port) Electronic Control Valves Model 131-01/631-01 Simple Proven Design Quality Solenoid Pilot Controls Ideal For SCADA Systems Multi-Function
More informationNEW AUTOJET PRECISION SPRAY CONTROL SYSTEM WITH ZONING
NEW AUTOJET 2008+ PRECISION SPRAY CONTROL SYSTEM WITH ZONING INCREASING THROUGHPUT AND DECREASING WASTE IN COATING, LUBRICATING AND DISPENSING OPERATIONS JUST GOT EASIER THAN EVER 98250 Modular Spray Manifold
More information3D TRASAR Automation - Boiler Blowdown Equipment
3D TRASAR Automation - Boiler Blowdown Equipment Reduces water and fuel costs by eliminating excessive blowdown Provides better program control and boiler reliability by maintaining boiler TDS at the optimum
More informationBimba Extruded Linear Thrusters 2X FF X EE DP 2X DD 2X Ø DD X EE DP U V W X Y Z R S Dimensions - ET T B 4X TAP AA THRU Ø BB C BORE X CC DP (OPP.SIDE)
Bimba Extruded Linear Thrusters Engineering Specifications Maximum Operating Pressure 140 psi (10 bar) Temperature Range 15 to 160 degrees F (-10 to 70 degrees C) Expected Service Life 1,500 miles (with
More informationPSF50 Paddle flow switch
Paddle Flow Switch Paddle Flow Switch PSF50 Paddle flow switch Paddle flap flow / no flow switch Economically priced flow/no flow paddle operated flow switch. Simple and reliable design for liquids up
More informationMS Application. Features. Proportional Valve Actuator General Instructions
Proportional Valve Actuator Application The Proportional Valve Actuator is a non-spring return actuator used with proportional to 10 Vdc or 4 to 0 ma controllers and standard 1/" to 1-1/4" two-way and
More informationInstallation Manual v1.0: Aurora Plus Turbo Kit ( ) 5.9L Dodge. Please read all instructions before installation.
Installation Manual v1.0: Aurora Plus - 4000 Turbo Kit (2003-2007) 5.9L Dodge Please read all instructions before installation. Figure 1: Aurora Plus - 4000 Kit Contents 1 Figure 2: Aurora Plus Hardware
More informationCompact Electric Actuated Ball Valves PVC Body, Teflon/EPDM Seals 1/2 to 1 inch Pipe
Compact Electric Actuated Ball Valves PVC Body, Teflon/EPDM Seals 1/2 to 1 inch Pipe SERIES Features Industrial quality miniature actuator Industrial grade True Union ball valve Visual valve position indicator
More informationLinear Thrusters/PneuMoment
/PneuMoment Extruded TE Series (Composite Bearings) 3.3-3.10 3.11-3.16 T Series Multiple Position T4 Series Movable Housing 3.17-3.22 3.23-3.24 3.25-3.28 3.29-3.32 Pneu-Moment Checklist PneuMoment Pneumatic
More informationDynabrade Portable Abrasive Belt Tools
Dynabrade Portable Abrasive Belt Tools Grind, Deburr, Blend, Clean, Polish and Finish Reorder No. D08.02R We offer a diverse line of products to help you get the job done. With expert knowledge, service
More informationAUTOMATIC SPRAY NOZZLES COATING DISPENSING GLAZING LAMINATING ROBOTIC APPLICATIONS MARKING FLAVORING HUMIDIFYING LUBRICATING MOISTURIZING
AUTOMATIC SPRAY NOZZLES COATING DISPENSING GLAZING LAMINATING ROBOTIC APPLICATIONS MARKING FLAVORING HUMIDIFYING LUBRICATING MOISTURIZING B1 AUTOMATIC NOZZLES INTRODUCTION INTRODUCTION If your application
More informationPARTS LIST WRANGLER 26-VS
PARTS LIST WRANGLER 26-VS ELECTRICAL WIRING ITEM PART NO. DESCRIPTION QTY. 1 2694161 UPPER WIRING HARNESS 1 2 2694171 LOWER WIRING HARNESS 1 3 2490811 BRUSH MOTOR WIRE ASSEMBLY 1 4 2396141 WIRE ASSEMBLY
More informationPRODUCT CATALOG COMPACT HYDRAULIC SPACE-SAVING, LONG-LASTING DEVICES FOR DEMANDING DESIGN REQUIREMENTS.
PRODUCT CATALOG COMPACT HYDRAULIC SPACE-SAVING, LONG-LASTING DEVICES FOR DEMANDING DESIGN REQUIREMENTS. TABLE OF CONTENTS 3 Compact Hydraulic 4 Product Features 4 Features and Benefits 5 How to Order 6
More informationLD Series Electronic Meters
LD Series Electronic Meters Manual and Preset Dispense Dispenses in gallons, quarts, pints and liters Easy to read LCD display with durable switches for long life Rugged engineered material for superior
More informationEM101 LOW FLOW MAGNETIC FLOWMETER INSTRUCTIONS
Spec Tech Industrial 203 Vest Ave. Valley Park, MO 63088 Phone: 888 SPECTECH Email: sales@spectechind.com www.spectechind.com EM101 EM101 LOW FLOW MAGNETIC FLOWMETER INSTRUCTIONS LOW FLOW MAGNETIC FLOWMETER
More information