- 8 amp (200VA) - 8 amp (200VA) - Sixteen (16) Fuse Protected Outputs. - Sixteen (16) PTC Protected Outputs.

Transcription

1 ALTV2416 Series CCTV ower Supplies Installation Guide Models Include: ALTV2416 ALTV2416CB 8 amp (200VA) 8 amp (200VA) 7 amp. 7 amp. - Sixteen (16) Fuse rotected Outputs. - Sixteen (16) TC rotected Outputs. ALTV ALTV CB 14 amp (350VA) 14 amp (350VA) 12.5 amp (350VA) amp (350VA). - Sixteen (16) Fuse rotected Outputs. - Sixteen (16) TC rotected Outputs. ALTV M ALTV CBM 12.5 amp (300VA) 12.5 amp (300VA) 10 amp (300VA). 10 amp (300VA). - Sixteen (16) Fuse rotected Outputs. - Sixteen (16) TC rotected Outputs. ALTV ALTV CB 28 amp (700VA) 28 amp (700VA) 25 amp (700VA). 25 amp (700VA). - Sixteen (16) Fuse rotected Outputs. - Sixteen (16) TC rotected Outputs. Rev

2 Overview: These Altronix CCTV ower Supplies provide / distributed via sixteen (16) fuse or TC protected outputs for powering CCTV Cameras, heaters and other video accessories. Sixteen (16) Output ALTV2416 Reference Chart: Altronix Model umber ALTV2416 ALTV2416CB ALTV ALTV CB ALTV M Output Voltage Total Output Current (ower) 8 amp 7 amp 8 amp 7 amp 14 amp 12.5 amp 14 amp 12.5 amp 12.5 amp 10 amp umber of Outputs TC rotected Outputs Fuse rotected Outputs Output Current (max per output) Main Fuse Ratings on Board 115VAC 50/60Hz Input Current 16 - x 3.5 amp (2) 5 amp/250v 1.9 amp 16 x amp (2) 5 amp/250v 1.9 amp 16 - x 3.5 amp (2) 5 amp/32v 2.7 amp 16 x amp (2) 5 amp/32v 2.7 amp 16 - x 3.5 amp amp ALTV CBM 12.5 amp 10 amp 16 x amp amp ALTV amp 25 amp 16 - x 3.5 amp (2) 5 amp/250v 5.4 amp ALTV CB 28 amp 25 amp 16 x amp (2) 5 amp/250v 5.4 amp Surge suppression. AC power LED indicator. ower O/OFF switch (ALTV2416 and ALTV2416CB). Illuminated power disconnect circuit breaker with manual reset for all other models. Unit maintains camera synchronization. Ease of installation saves time & eliminates costly labor. Spare fuses included (on fuse protected models). Specifications: Enclosure Dimensions: ALTV2416 and ALTV2416CB: 8.5 H x 7.5 W x 3.5 D ALTV M and ALTV CBM: 8.5 H x 7.5 W x 3.75 D ALTV , ALTV CB, ALTV and ALTV CB: 13.5 H x 13 W x 3.25 D Installation Instructions: 1. Mount unit in desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. lace the enclosure s upper keyholes over the two upper screws, level and secure. Mark the position of the lower two holes. Remove the enclosure. Drill the lower holes and install the three fasteners. lace the enclosure s upper keyholes over the two upper screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pg. 7,8). Secure enclosure to earth ground. 2. Slide switch on D board to OFF position for models ALTV2416 and ALTV2416CB (Fig. 1, pg. 4). Turn OFF main switch on all other models (Figs. 2-4, pgs. 4-6). 3. All units are factory set for operation ALTV2416series

3 For operation, adjust unit prior to mounting and applying power as follows: Change the wire position so that the black wire [28V] is connected to the terminal marked [] and the yellow wire [24V] is connected to the terminal marked [S]. 4. Connect AC power to the black and white flying lead of the transformer(s) (Figs. 1-4, pgs. 4-6). Use 18 AWG or larger for all power connections. 5. Measure output voltage before connecting devices. This helps avoid potential damage. Terminals marked [1-8] are positive of the same polarity. CAUTIO: Determine the maximum operating voltage of the equipment being powered before adjusting the output voltage. 6. Connect devices to terminals marked [1-1 through 8-8] on D8/D8CB board (Fig. 1, pgs. 4), carefully observing polarity [1-1 through 16-16] on 6W/6WCB board. 7. Slide switch on D board to O position for models ALTV2416, and ALTV2416CB (Fig. 1, pg. 4). Turn main switch on all other models to the RESET (O) position (Figs. 3-5, pgs. 5-6). 8. Green LED will illuminate when unit is powered. 9. Upon completion of wiring, secure enclosure door with screws (supplied). Caution: Equipment to be installed / serviced by authorized / trained personnel only. Shut branch circuit power before installing / servicing equipment. WARIG: To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture. This installation should be made by qualified service personnel and should conform to all local codes and in accordance with the ational Electrical Code. D8/D8CB - ower Distribution Module 1-8 ositive AC output. 1-8 egative AC output. Terminal Identification: 6W/6WCB - ower Distribution Module 1-16 ositive AC output egative AC output. ALTV2416series - 3 -

4 SW1 SW1 SW1 Fig. 1 - ALTV2416 ALTV2416CB Enclosure Door Back anel of Enclosure Used on TC Models (example: ALTV2416CB) MAI FUSE MAI FUSE F1 F2 F3 F4 F5 F6 F7 F8 MAI FUSE FUSED OWER OUTUTS R1 LED O OFF FUSED OWER OUTUTS R1 LED O OFF FUSED OWER OUTUTS R1 LED O OFF COMMO OWER OUTUTS IUT S COMMO OWER OUTUTS S IUT COMMO OWER OUTUTS S IUT or fused output 1 (Follow same procedure using terminals 2 & through 8 & fused outputs 2 through 8) or fused output 1 (Follow same procedure using terminals 2 & through 8 & fused outputs 2 through 8) White White Terminal Blocks for Fig VAC input 50/60 Hz. XFMR 115VAC input 50/60 Hz. XFMR Output (Factory Set) Output S S or fused or TC protected outputs 1 through 8. Fig. 2 ALTV ALTV CB Output (Factory Set) S Output S Used on TC Models (example: ALTV CB) IUT F U S E D O W E R O U T U T S F1 F2 F3 F4 F5 F6 F7 F 8 MAI FUSE S COMMO O W E R O U T U T S or fused output 1 (Follow same procedure using terminals 2 & through 8 & fused outputs 2 through 8) IUT C O M M O O W E R O U T U T S S F U S E D O W E R O U T U T S MAI FUSE ower Switch MAI FUSE F U SED OWER O U T U T S IUT COMMO OWER OUTUTS S Terminal Blocks for Fig VAC input 50/60 Hz, White XFMR* or fused or TC protected outputs 1 through ALTV2416series

5 Fig. 3 ALTV M ALTV CBM ower Switch Used on TC Models (example: ALTV CBM) common outputs protected outputs common outputs protected outputs Transformer underneath power supply board XFMR Input S XFMR Input S TC s 6W 3.5A 250V For continuous protection against risk of fire replace fuses with same type and rating. 6W Terminal Blocks for Fig. 3 or fused or TC protected outputs 1 through 16. Input: or operation. ALTV2416series - 5 -

6 Fig. 4 ALTV ALTV CB Used on TC Models (example: ALTV CB) or fused output 1 (Follow same procedure using terminals 2 & through 8 & fused outputs 2 through 8) IUT COMMO OWER OUTUTS S FUSED OWER OUTUTS MAI FUSE F U S E D O W E R O U T U TS IUT MAI FUSE MAI FUSE C O M M O O W E R O U T U TS S F1 F2 F3 F4 F5 F 6 F 7 F 8 ALTROIX COR. MADE I USA BROOKLY, Y FUSED OWER O UTUTS IUT C O M M O O W E R O U T U TS ower Switch Output (Factory Set) S 115VAC input, 50/60 Hz. XFMR* XFMR* Output S White Terminal Blocks for Fig. 4 or fused or TC protected outputs 1 through ALTV2416series

7 Enclosure Dimensions for: ALTV2416 ALTV2416CB 8.5 H x 7.5 W x 3.5 D Enclosure Dimensions for: ALTV M ALTV CBM 8.5 H x 7.5 W x 3.75 D 3.63" 1.25" 3.85" 7.25" 1.25" 0.60" 0.60" 1.25" 0.90" 0.90" 8.13" 8.13" 8.13" 1.75" 1.25" 0.60" 0.60" 3.85" 7.25" 3.85" 7.25" ALTV2416series - 7 -

8 Enclosure Dimensions for: ALTV ALTV CB ALTV ALTV CB 13.5 H x 13 W x 3.5 D Altronix is not responsible for any typographical errors. Altronix Corp th Street, Brooklyn, ew York USA, , fax: web site: info@altronix.com, Lifetime Warranty, Made in U.S.A. II1ALTV2416Series G17L MEMBER ALTV2416series