NASSAU 1000E - Electric Roller Shutter. Technical Specifications

Size: px

Start display at page:

Download "NASSAU 1000E - Electric Roller Shutter. Technical Specifications"

Daisy Ellis
5 years ago
Views:

NASSAU 00E - Electric Roller Shutter galvanised concave steel laths, (76mm), of suitable gauge to suit the application Each lath is retained by a nylon, pressed steel or malleable iron end lock fixed

1 NASSAU 00E - Electric Roller Shutter galvanised concave steel laths, (76mm), of suitable gauge to suit the application Each lath is retained by a nylon, pressed steel or malleable iron end lock fixed with galvanised steel rivets Cast Iron wind locks are fitted to help prevent the curtain being forced out of the guide during high winds, as and when required A rigid inverted T section bottom rail, formed from either a cold rolled galavanised section, or mild steel angles, bolted back to back, depending on the width of the shutter Specially designed tapered bottom rails can be supplied to suit sloping floors at additional cost come galvaised as standard Powder Coated and Plastisol finish is available at addtional cost unless specified otherwise can be supplied at additional cost specified otherwise Max Projection application Barrels are fitted in conjunction with an appropriate safety device ie Safedrive motor unit, safety bearing or counterbalance springs Motor Side Power Supply (By Others) Operator Switch To Suit Door Clear Opening Height A variety of electric motors are used depending upon the required application 415 volt 3 phase motors are normally used, however 240 volt single phase motors can be used in some circumstances A push button station is provided with UP, DOWN and STOP buttons Please contacrt us for full details of electrical specifications for your required operation and application 300 (Non Drive) Stuctural Opening Width 450 (Motor) wwwnassaucouk T: F: E: info@nassaucouk

NASSAU 00HC - Hand Chain Roller Shutter galvanised concave steel laths, (76mm), of suitable gauge to suit the application Each lath is retained by a nylon, pressed steel or malleable iron end lock

2 NASSAU 00HC - Hand Chain Roller Shutter galvanised concave steel laths, (76mm), of suitable gauge to suit the application Each lath is retained by a nylon, pressed steel or malleable iron end lock fixed with galvanised steel rivets Cast Iron wind locks are fitted to help prevent the curtain being forced out of the guide during high winds, as and when required come galvaised as standard Powder Coated and Plastisol finish is available at addtional cost A rigid inverted T section bottom rail, formed from either a cold rolled galavanised section, or mild steel angles, bolted back to back, depending on the width of the shutter Specially designed tapered bottom rails can be supplied to suit sloping floors at additional cost can be supplied at additional cost specified otherwise unless specified otherwise Haul Chain Via continuous galvanised steel hauling chain connected to a suitable reduction chain or gear reduction system Door Locking A pressed steel locking box is fitted to the side guide to secure the hand chain when the door is not in use, and is designed to accept the clients own security padlock Additional locking solutions are available at additional cost INTERNAL Stuctural Opening Width Safety Brake (Where Applicable) CHAIN OP wwwnassaucouk T: F: E: info@nassaucouk Constructed from mild steel tebe of suitable outside application The barrel encases helical springs, which are securely fitted inside the barrel, and are supported by purpose made cast iron or sg iron castings The springs counter-balance the shutter

NASSAU 00PU - Push Up Roller Shutter galvanised concave steel laths (76mm x 22swg) Each lath is retained by a nylon end lock fixed with galvanised steel rivets Flat 50mm Lath is available instead at

3 NASSAU 00PU - Push Up Roller Shutter galvanised concave steel laths (76mm x 22swg) Each lath is retained by a nylon end lock fixed with galvanised steel rivets Flat 50mm Lath is available instead at addtional cost A rigid inverted L or T section bottom rail, formed from a cold rolled galavanised section Constructed from mild steel tebe of suitable outside application The barrel encases helical springs, which are securely fitted inside the barrel, and are supported by purpose made cast iron or sg iron castings The springs counter-balance the shutter Manually push up and pull down with a pull down pole for taller applications unless specified otherwise can be supplied at additional cost specified otherwise 800 Approx Low Level Guide Locks 20 Door Locking Guide locks come as standard Bottom rail locks are avaialble at additional cost 150 Structural Opening Width 150 come galvaised as standard If Flats have been order these will come primer painted as standard Powder Coated and Plastisol finish is available at addtional cost PLAN wwwnassaucouk T: F: E: info@nassaucouk

NASSAU 00TM - Tube Motor Roller Shutter The shutter curtain is constructed from cold galvanised concave steel laths (76mm x 22swg) Other gauges may be supplied depending on the shutter width Each

4 NASSAU 00TM - Tube Motor Roller Shutter The shutter curtain is constructed from cold galvanised concave steel laths (76mm x 22swg) Other gauges may be supplied depending on the shutter width Each lath is retained by pressed steel or nylon end locks fixed with galvanised steel rivets A rigid inverted L or T section bottom rail, formed from a cold rolled galvanised section application The barrel encases the 240 volt tubular motor The main body of the motor is fixed to the door bracket plate and the outer body rotates the barrel, opening and closing the door The motors are 240 volts and are encased in the roller tube Motors can be supplied with or without an emergency hand crank facility normal operation is by paddle switch or keyswitch Remote control is via key fob type transmitter unless specified otherwise can be supplied at additional cost specified otherwise Structural Opening Width Power Requirement A single phase 13 amp 3 pin plug socket is required (within 1m of each door opening) for each tube motor installation For multiple installations, group controllers can be supplied come galvaised as standard Powder Coated and Plastisol finish is available at addtional cost Safety Brake (Where Applicable) Tube Motor wwwnassaucouk T: F: E: info@nassaucouk

Structural Opening Width NASSAU 2000I/FA - Insulated Roller Shutters ROLLER CURTAIN The shutter curtain is constructed from 90mm or 0mm twin interlocking cold rolled galvanised steel laths, infilled

fix to the underside of the lintel to form a seal between the lintel and the shutter curtain SIDE GUIDES Specially designed galvanised guide sections incorporating twin vertical brush seals to both

5 Structural Opening Width NASSAU 2000I/FA - Insulated Roller Shutters ROLLER CURTAIN The shutter curtain is constructed from 90mm or 0mm twin interlocking cold rolled galvanised steel laths, infilled with CFC free insulation Each lath is retained by nylon endlocks fixed and secured by steel rivets The bottom lath incorporates a rubber seal HEADSEAL 0mm or 150mm nylon brushstrips is supplied to fix to the underside of the lintel to form a seal between the lintel and the shutter curtain SIDE GUIDES Specially designed galvanised guide sections incorporating twin vertical brush seals to both sides of each guide ROLLER BARREL application Barrels are fitted in conjunction with an appropriate safety device, ie Safedrive motor unit OPERATION A variety of electric motors are used, depending upon the application: NASSAU 2000I Insulated Roller Shutter 415v 3 Phase Safe Drive NASSAU 2000FA Insulated Roller Shutter 415v 3 Phase Safe Drive Fast Action NASSAU 2000FA Insulated Roller Shutter 415v 3 Phase Safe Drive Fast Action Inverter Drive Motor (additional costs apply) Additional operating controls such as induction loops, radar and radio controls, plus relevant safety features are commonly used FINISH Side guides, supporting angles and door curtain are galavanised as standard Non-Galvanised sections are primer painted The shutter curtain is available in a range of plastisol colours and can be powder coated COIL CASINGS/FASCIAS/MOTOR COVERS Coil casings, hoods, fascias and motor covers can be supplied at additional cost and are supplied galvanised unless specified otherwise WINDOWS Rows of double glazed Perspex windows can be incorporated into the shutter laths at additional cost 300 Motor Side Operator Switch 400 To Suit Power Supply (By Others) ENLARGED GUIDE FIXING DETAIL Door Guides c/w Integrated Brush Seal Brush Seal At Head Bottom Seal To Door Curtain 0 wwwnassaucouk T: F: E: info@nassaucouk

Reflection. Aluminium Sectional Doors

Reflection. Aluminium Sectional Doors Reflection Aluminium Sectional Doors The Reflection aluminium sectional door features a chic round edge aluminium extrusion that can be clad with either glass or acrylic. Featuring a strong, sleek and