AEROSYSTEM POLE AND BRACKET SPECIFICATIONS NO PAIN, ALL GAIN ORDERING CHART FINISHES. by LSI Courtsider Sports Lighting. Installation As Easy As 1 2 3

Transcription

1 POLE AND BRACKET SPECIFICATIONS NO PAIN, ALL GAIN 3' The Aerosystem s modular assembly process is simple genius. The components of the system have been designed to be easy to install, easy to handle, and extremely durable. The system consists of: fixture, extension arm, two cast end connectors, pole top hub, and pole. 2' NUT WASHER HANDHOLE 12" ABOVE BASE 3/4" HALF COUPLING FOR WIRING HANDHOLE BASE PLATE BOLT PROJECTION LEVELING NUT 20' 6 Housing 7 One-piece, die-cast aluminum construction is stronger than fabricated or extruded boxes. Unique, aerodynamic shape creates less wind loading requirement for pole. End Connectors Cast aluminum end connectors join the fixture to the extension arm, and the extension arm to the pole top hub. 48" ANCHOR BOLT FOUNDATION ANCHOR BASE POLES ANGLE DIRECT BURIAL POLES Single, D180, and D70 pole shafts are electro welded ASTM-A513 4" O.D. 10 Ga. round steel tubing. Quad pole shaft is ASTM-A513 5" O.D. 11 Ga. round steel tubing. 4" O.D. steel tubing is approximately 6 lbs. per ft. 5" O.D. steel tubing is approximately 7 lbs. per ft. Anchor base poles are furnished with anchor bolts and zinc plated double nuts and washers. Galvanized anchor bolts are Anchor bolts conform with ASTM-A36 with a minimum yield strength of 36,000 PSI. Base is ASTM-A36 hot-rolled steel plate with a minimum yield strength of 36,000 PSI. 3" x 6" reinforced handhole is 12" above base plate, cover is provided. Ground lug is standard. ORDERING CHART Assembly Type 5 Hinged Ballast Tray Ballast is mounted on hinged tray that is removable for fixture installation or maintenance. During installation, removing the ballast tray significantly reduces the weight of the fixture. Toolless release mechanism for hassle-free operation. EXAMPLE OF A TYPICAL ORDER 4 3 Reflector 1000 Watt Metal Halide Reduced lamp. Horizontal burning position. Forward Throw reflector designed to light the court area uniformly, while eliminating stray light and producing a sharp backside cutoff. Thermal Shock Resistant Glass Lens Clear, flat, tempered glass lens is sealed to door frame with a one-piece extruded silicone gasket. Installation As Easy As Extension Arm 1 2 Lamp Door Frame + Protective Gasket One-piece, die-cast, removable door frame allows easy maintenance. Door frame seals against the housing by a one-piece extruded silicone gasket. IP65 Rating Standard design completely seals the Aerosystem housing from penetration of external contaminents, which allows for IP65 rating. To assemble: Mount (1) end connector to pole top fitter, mount (1) end connector to fixture. Slide pole top fitter on pole, slide extension arm on end connector. Slide fixture in extension arm. Steel tube slides over cast end connectors, and is secured with stainless steel hardware at each end. 9 ARO-A MT - Multi Tap1 480V 220/240V 50HZ MT EPA s on standard pole configurations are guaranteed up to 80 MPH. Please consult factory for areas with wind ratings higher than 80 MPH. Caution: The Courtsider Sports Lighting guarantee does not apply if the pole/bracket/fixture combination is used to support any other items, such as flags, pennants, or signs, which would add stress to the pole. Courtsider Sports Lighting cannot accept responsibility for harm or damage caused in these situations. Pole Type Pole Height4 Pole Material Assembly Finish AB -Anchor Base3 DB - Direct Burial " o.d. 10 Ga. Steel " o.d. 11 Ga. Steel 507-5" o.d. 7 Ga. Steel6 BLK - Black GRN - Green BRZ - Bronze PLP - Platinum Plus BUF - Buff WHT - White GPT - Graphite MSV - Metallic Silver Luminaire Wattage Luminaire Voltage ARO-A (single) Watt ARO-B (twin 180 ) Metal Halide ARO-C (twin 70 ) Watt PulseARO-D (quad) Start Metal Halide Watt PulseStart Metal Halide Weatherproof duplex receptacle is Ground fault circuit interrupter is Two-piece fabricated aluminum base cover is standard for anchor base poles. Pole top hub externally slipfits 4" or 5" O.D. pole. Hardware to level bracket is internally threaded, concealing it from view for a cleaner appearance. A through bolt is not required. Extension arm is ASTM-A513 4" O.D. round steel tubing. AB Pole Options BLK GFI - Weatherproof Luminaire Options Duplex Receptacle w/ 1 - MT (multi-tap ballasts include taps for 120V, 208V, 240V, or 277V) GFCI protection8 2 - For international applications where 50hz power is standard (e.g. Europe & Asia). RCS - House Side Shield7 LAB - Less Anchor Bolts 3 - All anchor base assemblies are supplied with galvanized anchor bolts and base covers. 4 - For anchor base assemblies, the heights shown are the pole length. The fixture mounting height will be 2' higher than the pole height using the upsweep bracket (e.g. with a 20' pole the fixture mounting height is 22'). For direct burial assemblies, the height shown is the above grade section. Direct burial poles will also include a 4' below grade section (e.g. a 20' direct burial pole is 24' overall length). Direct burial poles are limited to maximum 24' above grade height. 5-4" poles are available only up to 22' height. 6 - The 5" o.d., 7 gauge pole is used for all quad assemblies. 7- Under normal use, the Aerosystem fixture produces acceptable light cutoff. For highly sensitive applications, the optional external rear cutoff shield is available. 8 - The GFI receptacle installs in the standard handhole location 12" above the pole base. wet location AEROSYSTEM FINISHES Pole Top Hub Rotatable, cast aluminum pole top hub is available to externally slipfit 4" or 5" diameter poles. Mounting holes for various assembly configurations are pre-drilled. Concealed, stainless steel set screws are used for leveling and securing hub to top of pole. Cap is included. Black Green Bronze All Aerosystem components are finished with DuraGrip, Courtsider Sports Lighting s revolutionary, superior, Platinum Plus White baked-on powder finishing process that produces an exceptionally attractive appearance. DuraGrip polyester finish LSI COURTSIDER SPORTS LIGHTING Alliance Road Cincinnati, Ohio (800) FAX (800) courtsider@lsi-industries.com Buff Graphite Metallic Silver withstands extreme weather changes without cracking or peeling. Finish is guaranteed for a full five years. by LSI Courtsider Sports Lighting 2010 LSI INDUSTRIES INC /10

2 AEROSYSTEM: A NEW SPIN IN TENNIS COURT LIGHTING LSI Courtsider Sports Lighting, the innovator in tennis court lighting, presents Aerosystem. More than just a light fixture, the Aerosystem breaks new ground in aesthetics, construction, and functionality. Departing from the dated shoebox look, the Aerosystem presents a distinctive and progressive, yet low profile appearance. LSI Courtsider has thoroughly simplified the installation of the assembly with the Aerosystem s modular mounting design. Its die-cast construction provides unparalleled durability, and is available in a selection of finishes to complement the court environment. In addition, the Aerosystem provides brilliant, glare-free illumination for players, with precise light control and minimal light spillage outside of the court area. Unlike traditional floodlighting systems, which produce harsh glare, the Aerosystem creates a low impact, environmentally friendly lighting effect. The Aerosystem is the perfect lighting choice for high schools, universities, resorts, country clubs, condominium complexes, and private residences. Powerful performance and smashingly sleek aesthetics make the Aerosystem a sure courtside winner. THE AEROSYSTEM APPROACH Pole & Fixture Placement Installing the Aerosystem courtside removes the light source from the player s normal line of vision. This placement provides excellent illumination on the flight of the tennis ball, and the surface of the court. In general, proper lighting of the ball requires pole placement on the sides of the court which are near, or behind the baseline of the court. (see standard layouts) Fixture The Aerosystem s Forward Throw reflector and concealed light source provide a sharp cutoff to prevent disabling glare and unwanted spill light. Its Metal Halide lamp source promotes energy efficiency and longer life. This combination ensures economic operation and minimal maintenance costs. ACHIEVE THE HIGHEST LIGHT QUALITY for relamping. Lob shots over 22' are illuminated by the light reflected from the court surface. Quantity of Light A rapidly moving tennis ball requires relatively high levels of illumination, and will vary according to the caliber of play at the facility. The standard layouts provided by LSI Courtsider Sports Lighting are designed for specific levels of play. Each system uses the proper number of poles and fixtures to produce the proper amount of light for the level of play. Uniformity of Light STANDARD LAYOUTS LAYOUT 1 LAYOUT 3 LAYOUT 5 The tennis ball is easier to follow under uniform lighting conditions. The optical design and pole / fixture placement of the Aerosystem insures an even light distribution over the entire court area. Customized Foot-candle Chart Recreational Play Club/Tournament Narrow Recreational (6) ARO-A (8) ARO-A (6) ARO-A (1) ARO-B (2) ARO-C LAYOUT 2 A customized foot-candle chart, illustrating the Aerosystem for your project, is available upon request. Contact LSI Courtsider Sports Lighting for more details. LAYOUT 4 Full Size Recreational Full Size Club/Tournament Narrow Club/Tournament (6) ARO-A (3) ARO-B (8) ARO-A (4) ARO-B (8) ARO-A (2) ARO-C (1) ARO-D CONFIGURATIONS Fixture Mounting Height At a mounting height of 22 feet, the Aerosystem effectively distributes the proper amount of light on the court and eliminates stray light to surrounding areas. The low fixture mounting height is more visually appealing, and provides easier accessibility LSI Courtsider Sports Lighting is committed to providing community-friendly lighting that delivers high quality, energy efficient illumination while eliminating unnecessary uplight and minimizing light trespass. The Aerosystem is considered to be community-friendly, meeting IESNA s full cutoff classification. LAYOUT 6 Single D180 ARO-A Assembly (1) 1000 Watt Fixture (1) Single Bracket ARO-B Assembly D70 Q90 ARO-C Assembly ARO-D Assembly (4) 1000 Watt Fixtures (4) Single Brackets (1) 20' x 5" O.D. Pole

3 AEROSYSTEM: A NEW SPIN IN TENNIS COURT LIGHTING LSI Courtsider Sports Lighting, the innovator in tennis court lighting, presents Aerosystem. More than just a light fixture, the Aerosystem breaks new ground in aesthetics, construction, and functionality. Departing from the dated shoebox look, the Aerosystem presents a distinctive and progressive, yet low profile appearance. LSI Courtsider has thoroughly simplified the installation of the assembly with the Aerosystem s modular mounting design. Its die-cast construction provides unparalleled durability, and is available in a selection of finishes to complement the court environment. In addition, the Aerosystem provides brilliant, glare-free illumination for players, with precise light control and minimal light spillage outside of the court area. Unlike traditional floodlighting systems, which produce harsh glare, the Aerosystem creates a low impact, environmentally friendly lighting effect. The Aerosystem is the perfect lighting choice for high schools, universities, resorts, country clubs, condominium complexes, and private residences. Powerful performance and smashingly sleek aesthetics make the Aerosystem a sure courtside winner. THE AEROSYSTEM APPROACH Pole & Fixture Placement Installing the Aerosystem courtside removes the light source from the player s normal line of vision. This placement provides excellent illumination on the flight of the tennis ball, and the surface of the court. In general, proper lighting of the ball requires pole placement on the sides of the court which are near, or behind the baseline of the court. (see standard layouts) Fixture The Aerosystem s Forward Throw reflector and concealed light source provide a sharp cutoff to prevent disabling glare and unwanted spill light. Its Metal Halide lamp source promotes energy efficiency and longer life. This combination ensures economic operation and minimal maintenance costs. ACHIEVE THE HIGHEST LIGHT QUALITY for relamping. Lob shots over 22' are illuminated by the light reflected from the court surface. Quantity of Light A rapidly moving tennis ball requires relatively high levels of illumination, and will vary according to the caliber of play at the facility. The standard layouts provided by LSI Courtsider Sports Lighting are designed for specific levels of play. Each system uses the proper number of poles and fixtures to produce the proper amount of light for the level of play. Uniformity of Light STANDARD LAYOUTS LAYOUT 1 LAYOUT 3 LAYOUT 5 The tennis ball is easier to follow under uniform lighting conditions. The optical design and pole / fixture placement of the Aerosystem insures an even light distribution over the entire court area. Customized Foot-candle Chart Recreational Play Club/Tournament Narrow Recreational (6) ARO-A (8) ARO-A (6) ARO-A (1) ARO-B (2) ARO-C LAYOUT 2 A customized foot-candle chart, illustrating the Aerosystem for your project, is available upon request. Contact LSI Courtsider Sports Lighting for more details. LAYOUT 4 Full Size Recreational Full Size Club/Tournament Narrow Club/Tournament (6) ARO-A (3) ARO-B (8) ARO-A (4) ARO-B (8) ARO-A (2) ARO-C (1) ARO-D CONFIGURATIONS Fixture Mounting Height At a mounting height of 22 feet, the Aerosystem effectively distributes the proper amount of light on the court and eliminates stray light to surrounding areas. The low fixture mounting height is more visually appealing, and provides easier accessibility LSI Courtsider Sports Lighting is committed to providing community-friendly lighting that delivers high quality, energy efficient illumination while eliminating unnecessary uplight and minimizing light trespass. The Aerosystem is considered to be community-friendly, meeting IESNA s full cutoff classification. LAYOUT 6 Single D180 ARO-A Assembly (1) 1000 Watt Fixture (1) Single Bracket ARO-B Assembly D70 Q90 ARO-C Assembly ARO-D Assembly (4) 1000 Watt Fixtures (4) Single Brackets (1) 20' x 5" O.D. Pole

4 AEROSYSTEM: A NEW SPIN IN TENNIS COURT LIGHTING LSI Courtsider Sports Lighting, the innovator in tennis court lighting, presents Aerosystem. More than just a light fixture, the Aerosystem breaks new ground in aesthetics, construction, and functionality. Departing from the dated shoebox look, the Aerosystem presents a distinctive and progressive, yet low profile appearance. LSI Courtsider has thoroughly simplified the installation of the assembly with the Aerosystem s modular mounting design. Its die-cast construction provides unparalleled durability, and is available in a selection of finishes to complement the court environment. In addition, the Aerosystem provides brilliant, glare-free illumination for players, with precise light control and minimal light spillage outside of the court area. Unlike traditional floodlighting systems, which produce harsh glare, the Aerosystem creates a low impact, environmentally friendly lighting effect. The Aerosystem is the perfect lighting choice for high schools, universities, resorts, country clubs, condominium complexes, and private residences. Powerful performance and smashingly sleek aesthetics make the Aerosystem a sure courtside winner. THE AEROSYSTEM APPROACH Pole & Fixture Placement Installing the Aerosystem courtside removes the light source from the player s normal line of vision. This placement provides excellent illumination on the flight of the tennis ball, and the surface of the court. In general, proper lighting of the ball requires pole placement on the sides of the court which are near, or behind the baseline of the court. (see standard layouts) Fixture The Aerosystem s Forward Throw reflector and concealed light source provide a sharp cutoff to prevent disabling glare and unwanted spill light. Its Metal Halide lamp source promotes energy efficiency and longer life. This combination ensures economic operation and minimal maintenance costs. ACHIEVE THE HIGHEST LIGHT QUALITY for relamping. Lob shots over 22' are illuminated by the light reflected from the court surface. Quantity of Light A rapidly moving tennis ball requires relatively high levels of illumination, and will vary according to the caliber of play at the facility. The standard layouts provided by LSI Courtsider Sports Lighting are designed for specific levels of play. Each system uses the proper number of poles and fixtures to produce the proper amount of light for the level of play. Uniformity of Light STANDARD LAYOUTS LAYOUT 1 LAYOUT 3 LAYOUT 5 The tennis ball is easier to follow under uniform lighting conditions. The optical design and pole / fixture placement of the Aerosystem insures an even light distribution over the entire court area. Customized Foot-candle Chart Recreational Play Club/Tournament Narrow Recreational (6) ARO-A (8) ARO-A (6) ARO-A (1) ARO-B (2) ARO-C LAYOUT 2 A customized foot-candle chart, illustrating the Aerosystem for your project, is available upon request. Contact LSI Courtsider Sports Lighting for more details. LAYOUT 4 Full Size Recreational Full Size Club/Tournament Narrow Club/Tournament (6) ARO-A (3) ARO-B (8) ARO-A (4) ARO-B (8) ARO-A (2) ARO-C (1) ARO-D CONFIGURATIONS Fixture Mounting Height At a mounting height of 22 feet, the Aerosystem effectively distributes the proper amount of light on the court and eliminates stray light to surrounding areas. The low fixture mounting height is more visually appealing, and provides easier accessibility LSI Courtsider Sports Lighting is committed to providing community-friendly lighting that delivers high quality, energy efficient illumination while eliminating unnecessary uplight and minimizing light trespass. The Aerosystem is considered to be community-friendly, meeting IESNA s full cutoff classification. LAYOUT 6 Single D180 ARO-A Assembly (1) 1000 Watt Fixture (1) Single Bracket ARO-B Assembly D70 Q90 ARO-C Assembly ARO-D Assembly (4) 1000 Watt Fixtures (4) Single Brackets (1) 20' x 5" O.D. Pole

5 POLE AND BRACKET SPECIFICATIONS NO PAIN, ALL GAIN 3' The Aerosystem s modular assembly process is simple genius. The components of the system have been designed to be easy to install, easy to handle, and extremely durable. The system consists of: fixture, extension arm, two cast end connectors, pole top hub, and pole. 2' NUT WASHER HANDHOLE 12" ABOVE BASE 3/4" HALF COUPLING FOR WIRING HANDHOLE BASE PLATE BOLT PROJECTION LEVELING NUT 20' 6 Housing 7 One-piece, die-cast aluminum construction is stronger than fabricated or extruded boxes. Unique, aerodynamic shape creates less wind loading requirement for pole. End Connectors Cast aluminum end connectors join the fixture to the extension arm, and the extension arm to the pole top hub. 48" ANCHOR BOLT FOUNDATION ANCHOR BASE POLES ANGLE DIRECT BURIAL POLES Single, D180, and D70 pole shafts are electro welded ASTM-A513 4" O.D. 10 Ga. round steel tubing. Quad pole shaft is ASTM-A513 5" O.D. 11 Ga. round steel tubing. 4" O.D. steel tubing is approximately 6 lbs. per ft. 5" O.D. steel tubing is approximately 7 lbs. per ft. Anchor base poles are furnished with anchor bolts and zinc plated double nuts and washers. Galvanized anchor bolts are Anchor bolts conform with ASTM-A36 with a minimum yield strength of 36,000 PSI. Base is ASTM-A36 hot-rolled steel plate with a minimum yield strength of 36,000 PSI. 3" x 6" reinforced handhole is 12" above base plate, cover is provided. Ground lug is standard. ORDERING CHART Assembly Type 5 Hinged Ballast Tray Ballast is mounted on hinged tray that is removable for fixture installation or maintenance. During installation, removing the ballast tray significantly reduces the weight of the fixture. Toolless release mechanism for hassle-free operation. EXAMPLE OF A TYPICAL ORDER 4 3 Reflector 1000 Watt Metal Halide Reduced lamp. Horizontal burning position. Forward Throw reflector designed to light the court area uniformly, while eliminating stray light and producing a sharp backside cutoff. Thermal Shock Resistant Glass Lens Clear, flat, tempered glass lens is sealed to door frame with a one-piece extruded silicone gasket. Installation As Easy As Extension Arm 1 2 Lamp Door Frame + Protective Gasket One-piece, die-cast, removable door frame allows easy maintenance. Door frame seals against the housing by a one-piece extruded silicone gasket. IP65 Rating Standard design completely seals the Aerosystem housing from penetration of external contaminents, which allows for IP65 rating. To assemble: Mount (1) end connector to pole top fitter, mount (1) end connector to fixture. Slide pole top fitter on pole, slide extension arm on end connector. Slide fixture in extension arm. Steel tube slides over cast end connectors, and is secured with stainless steel hardware at each end. 9 ARO-A MT - Multi Tap1 480V 220/240V 50HZ MT EPA s on standard pole configurations are guaranteed up to 80 MPH. Please consult factory for areas with wind ratings higher than 80 MPH. Caution: The Courtsider Sports Lighting guarantee does not apply if the pole/bracket/fixture combination is used to support any other items, such as flags, pennants, or signs, which would add stress to the pole. Courtsider Sports Lighting cannot accept responsibility for harm or damage caused in these situations. Pole Type Pole Height4 Pole Material Assembly Finish AB -Anchor Base3 DB - Direct Burial " o.d. 10 Ga. Steel " o.d. 11 Ga. Steel 507-5" o.d. 7 Ga. Steel6 BLK - Black GRN - Green BRZ - Bronze PLP - Platinum Plus BUF - Buff WHT - White GPT - Graphite MSV - Metallic Silver Luminaire Wattage Luminaire Voltage ARO-A (single) Watt ARO-B (twin 180 ) Metal Halide ARO-C (twin 70 ) Watt PulseARO-D (quad) Start Metal Halide Watt PulseStart Metal Halide Weatherproof duplex receptacle is Ground fault circuit interrupter is Two-piece fabricated aluminum base cover is standard for anchor base poles. Pole top hub externally slipfits 4" or 5" O.D. pole. Hardware to level bracket is internally threaded, concealing it from view for a cleaner appearance. A through bolt is not required. Extension arm is ASTM-A513 4" O.D. round steel tubing. AB Pole Options BLK GFI - Weatherproof Luminaire Options Duplex Receptacle w/ 1 - MT (multi-tap ballasts include taps for 120V, 208V, 240V, or 277V) GFCI protection8 2 - For international applications where 50hz power is standard (e.g. Europe & Asia). RCS - House Side Shield7 LAB - Less Anchor Bolts 3 - All anchor base assemblies are supplied with galvanized anchor bolts and base covers. 4 - For anchor base assemblies, the heights shown are the pole length. The fixture mounting height will be 2' higher than the pole height using the upsweep bracket (e.g. with a 20' pole the fixture mounting height is 22'). For direct burial assemblies, the height shown is the above grade section. Direct burial poles will also include a 4' below grade section (e.g. a 20' direct burial pole is 24' overall length). Direct burial poles are limited to maximum 24' above grade height. 5-4" poles are available only up to 22' height. 6 - The 5" o.d., 7 gauge pole is used for all quad assemblies. 7- Under normal use, the Aerosystem fixture produces acceptable light cutoff. For highly sensitive applications, the optional external rear cutoff shield is available. 8 - The GFI receptacle installs in the standard handhole location 12" above the pole base. wet location AEROSYSTEM FINISHES Pole Top Hub Rotatable, cast aluminum pole top hub is available to externally slipfit 4" or 5" diameter poles. Mounting holes for various assembly configurations are pre-drilled. Concealed, stainless steel set screws are used for leveling and securing hub to top of pole. Cap is included. Black Green Bronze All Aerosystem components are finished with DuraGrip, Courtsider Sports Lighting s revolutionary, superior, Platinum Plus White baked-on powder finishing process that produces an exceptionally attractive appearance. DuraGrip polyester finish LSI COURTSIDER SPORTS LIGHTING Alliance Road Cincinnati, Ohio (800) FAX (800) courtsider@lsi-industries.com Buff Graphite Metallic Silver withstands extreme weather changes without cracking or peeling. Finish is guaranteed for a full five years. by LSI Courtsider Sports Lighting 2010 LSI INDUSTRIES INC /10

6 POLE AND BRACKET SPECIFICATIONS NO PAIN, ALL GAIN 3' The Aerosystem s modular assembly process is simple genius. The components of the system have been designed to be easy to install, easy to handle, and extremely durable. The system consists of: fixture, extension arm, two cast end connectors, pole top hub, and pole. 2' NUT WASHER HANDHOLE 12" ABOVE BASE 3/4" HALF COUPLING FOR WIRING HANDHOLE BASE PLATE BOLT PROJECTION LEVELING NUT 20' 6 Housing 7 One-piece, die-cast aluminum construction is stronger than fabricated or extruded boxes. Unique, aerodynamic shape creates less wind loading requirement for pole. End Connectors Cast aluminum end connectors join the fixture to the extension arm, and the extension arm to the pole top hub. 48" ANCHOR BOLT FOUNDATION ANCHOR BASE POLES ANGLE DIRECT BURIAL POLES Single, D180, and D70 pole shafts are electro welded ASTM-A513 4" O.D. 10 Ga. round steel tubing. Quad pole shaft is ASTM-A513 5" O.D. 11 Ga. round steel tubing. 4" O.D. steel tubing is approximately 6 lbs. per ft. 5" O.D. steel tubing is approximately 7 lbs. per ft. Anchor base poles are furnished with anchor bolts and zinc plated double nuts and washers. Galvanized anchor bolts are Anchor bolts conform with ASTM-A36 with a minimum yield strength of 36,000 PSI. Base is ASTM-A36 hot-rolled steel plate with a minimum yield strength of 36,000 PSI. 3" x 6" reinforced handhole is 12" above base plate, cover is provided. Ground lug is standard. ORDERING CHART Assembly Type 5 Hinged Ballast Tray Ballast is mounted on hinged tray that is removable for fixture installation or maintenance. During installation, removing the ballast tray significantly reduces the weight of the fixture. Toolless release mechanism for hassle-free operation. EXAMPLE OF A TYPICAL ORDER 4 3 Reflector 1000 Watt Metal Halide Reduced lamp. Horizontal burning position. Forward Throw reflector designed to light the court area uniformly, while eliminating stray light and producing a sharp backside cutoff. Thermal Shock Resistant Glass Lens Clear, flat, tempered glass lens is sealed to door frame with a one-piece extruded silicone gasket. Installation As Easy As Extension Arm 1 2 Lamp Door Frame + Protective Gasket One-piece, die-cast, removable door frame allows easy maintenance. Door frame seals against the housing by a one-piece extruded silicone gasket. IP65 Rating Standard design completely seals the Aerosystem housing from penetration of external contaminents, which allows for IP65 rating. To assemble: Mount (1) end connector to pole top fitter, mount (1) end connector to fixture. Slide pole top fitter on pole, slide extension arm on end connector. Slide fixture in extension arm. Steel tube slides over cast end connectors, and is secured with stainless steel hardware at each end. 9 ARO-A MT - Multi Tap1 480V 220/240V 50HZ MT EPA s on standard pole configurations are guaranteed up to 80 MPH. Please consult factory for areas with wind ratings higher than 80 MPH. Caution: The Courtsider Sports Lighting guarantee does not apply if the pole/bracket/fixture combination is used to support any other items, such as flags, pennants, or signs, which would add stress to the pole. Courtsider Sports Lighting cannot accept responsibility for harm or damage caused in these situations. Pole Type Pole Height4 Pole Material Assembly Finish AB -Anchor Base3 DB - Direct Burial " o.d. 10 Ga. Steel " o.d. 11 Ga. Steel 507-5" o.d. 7 Ga. Steel6 BLK - Black GRN - Green BRZ - Bronze PLP - Platinum Plus BUF - Buff WHT - White GPT - Graphite MSV - Metallic Silver Luminaire Wattage Luminaire Voltage ARO-A (single) Watt ARO-B (twin 180 ) Metal Halide ARO-C (twin 70 ) Watt PulseARO-D (quad) Start Metal Halide Watt PulseStart Metal Halide Weatherproof duplex receptacle is Ground fault circuit interrupter is Two-piece fabricated aluminum base cover is standard for anchor base poles. Pole top hub externally slipfits 4" or 5" O.D. pole. Hardware to level bracket is internally threaded, concealing it from view for a cleaner appearance. A through bolt is not required. Extension arm is ASTM-A513 4" O.D. round steel tubing. AB Pole Options BLK GFI - Weatherproof Luminaire Options Duplex Receptacle w/ 1 - MT (multi-tap ballasts include taps for 120V, 208V, 240V, or 277V) GFCI protection8 2 - For international applications where 50hz power is standard (e.g. Europe & Asia). RCS - House Side Shield7 LAB - Less Anchor Bolts 3 - All anchor base assemblies are supplied with galvanized anchor bolts and base covers. 4 - For anchor base assemblies, the heights shown are the pole length. The fixture mounting height will be 2' higher than the pole height using the upsweep bracket (e.g. with a 20' pole the fixture mounting height is 22'). For direct burial assemblies, the height shown is the above grade section. Direct burial poles will also include a 4' below grade section (e.g. a 20' direct burial pole is 24' overall length). Direct burial poles are limited to maximum 24' above grade height. 5-4" poles are available only up to 22' height. 6 - The 5" o.d., 7 gauge pole is used for all quad assemblies. 7- Under normal use, the Aerosystem fixture produces acceptable light cutoff. For highly sensitive applications, the optional external rear cutoff shield is available. 8 - The GFI receptacle installs in the standard handhole location 12" above the pole base. wet location AEROSYSTEM FINISHES Pole Top Hub Rotatable, cast aluminum pole top hub is available to externally slipfit 4" or 5" diameter poles. Mounting holes for various assembly configurations are pre-drilled. Concealed, stainless steel set screws are used for leveling and securing hub to top of pole. Cap is included. Black Green Bronze All Aerosystem components are finished with DuraGrip, Courtsider Sports Lighting s revolutionary, superior, Platinum Plus White baked-on powder finishing process that produces an exceptionally attractive appearance. DuraGrip polyester finish LSI COURTSIDER SPORTS LIGHTING Alliance Road Cincinnati, Ohio (800) FAX (800) courtsider@lsi-industries.com Buff Graphite Metallic Silver withstands extreme weather changes without cracking or peeling. Finish is guaranteed for a full five years. by LSI Courtsider Sports Lighting 2010 LSI INDUSTRIES INC /10