ASSEMBLY INSTRUCTIONS

Transcription

1 Give a New Leash on Life Best Friend Mobility SW 72nd Ave. Portland, OR Phone: Fax: info@bestfriendmobility.org

2 1

3 2

4 3 Frame Parts: 1. DC01A Left Sidearm 2. DC02A Left Front Harness Bar 3. DC01B Right Sidearm 4. DC02B Right Front Harness Bar 5. Front Harness Female Clips 6. DC09 Clip Connectors 7. Clip Connector Screws 8. DC07 Frame Connectors 9. Sidearm Bolts 10. Washers 11. DC04 Frame Supports 12. DC08 Upper Crossbar Connectors 13. DC03 Upper Rear Crossbar 14. SFT Connector 15. DC05 Lower Rear Crossbar 16. DC06A Right Wheel Connector 17. DC06B Left Wheel Connector 18. DC10 Rear Harness Support

5 4 Wheel Parts: 1. Wheel 2. Treads 3. Tire 4. Valve 5. Valve Cap 6. Bolt Head 7. Wheel Bolt 8. Washer 9. Nut

6 5 1. Required tools for assembling the dog wheelchair. 2. Shown are the different parts of the wheelchair frame. The sides of the frame are shown pre-assembled. 3. Shown are the wheel, the front and rear harnesses and straps. 4. Fit the Rear Harness Support to the Upper Crossbar Connector of the Left Sidearm. 5. Closeup of the Rear Harness Support being assembled with the Left Sidearm. Place the Connector Block Screw together inside the connector. 6. Hold the Connector Block Screw steady with a wrench while the Clip Connector Screw is tightened using a hex key.

7 6 7. Closeup of the Rear Harness Support being assembled with the Right Sidearm. 8. Placing the Clip Connector Screw to the Upper Crossbar Connector of the Sidearm. 9. Assemble the Rear Harness Support to the Right Sidearm using the Upper Crossbar Connector. Hold the Connector Block Screw steady with a wrench while the Clip Connector Screw is tightened using a hex key. 10. Attach the Lower Rear Crossbar (sheathed in foam) to both Sidearms. 11. Closeup of the Lower Rear Crossbar being attached to a Sidearm. Place the Connector Block Screw and the Clip Connector Screw together inside the Clip Connector. 12. Hold the Connector Block Screw steady with a wrench while the Clip Connector Screw is tightened usinga hex key.

8 7 13. Hold the Connector Block Screw steady with a wrench while the Clip Connector Screw is tightened using a hex key. 14. Insert the Left Front Harness Bar to the Left Sidearm. 15. Insert the Right Front Harness Bar to the Right Sidearm. 16. Assembled frame. 17. Hold the Connector Block Screw steady with a wrench while the Clip Connector Screw is tightened using a hex key. 18. Place the Wheel Bolt in the Lower Rear Connector and tighten. Please see Wheel Assembly diagram on Page 4 for parts placement.

9 8 19. Attach the Front Harness O-Rings to the Sidearm Bolts. 20. Attach the Male Clip from the Front Harness into the Female Clip on the front of the Sidearms. 21. The Rear Harness Lobster Clip being applied to the Rear Harness Support. 22. Rear Harness placed on the Rear Harness Support with the Lobster Clip. 23. Attach the cord throughout the eyelets of the pins on the Left and Right Sidearms. 24. Completed wheelchair with all harnesses, straps and wheels attached.