ATLANTES FREEDOM. Household Style Marine Toilet. Model A7, A8 and A9 Manufactured after July 2005)

Transcription

1 ATLANTES FREEDOM Household Style Marine Toilet Model A7, A8 and A9 Manufactured after July 2005) THE FOLLOWING ARE CAUTIONARY STATEMENTS THAT MUST BE READ AND FOLLOWED DURING BOTH INSTALLATION AND OPERATION WARNING: Raritan Engineering Company, Inc. recommends that a qualified person or electrician install this product. Equipment damage, injury to personnel or death could result from improper installation. Raritan Engineering Company, Inc. accepts no responsibility or liability for damage to equipment, or injury or death to personnel that may result from improper installation or operation of this product. WARNING: HAZARD OF FLOODING - Always shut off seacocks before leaving the boat unattended. Double clamp all below waterline hose fittings and check frequently for integrity. HAZARD OF SHOCK OR FIRE - Always use recommended fuse, circuit breaker and wire size. A7 and A8 Models with Flush Lever A9 Model with Wall Switch Flush Control Panel INTRODUCTION The Atlantes is Raritan s best electric macerating toilet. All working parts fit inside the one-piece porcelain bowl on Integral Intake Pump models. The powerful centrifugal macerating pump thoroughly breaks down waste in preparation for treatment or holding. Three systems are available: Integral Intake Pump - for above waterline installations only. Remote Intake Pump - for above and below waterline installations. Freshwater Solenoid Valve - for flushing with pressurized fresh water com 1

2 OPERATION Flush Lever The A7 model The A7 model is designed to work as a momentary unit using only microswitches to activate the motors. It is also a fail safe mode for the toilet control in the A8 model. The A8 model The A8 model contains an electronic toilet control which provides timed operation while still having momentary functionality if toilet control is removed. Operation: pull handle forward: Model A8 - starts a timed flush, intake pump starts followed by discharge pump. Model A7 - Hold to add water. push handle backward: In both models runs just the discharge pump for a dry bowl flush. EMPTY BOWL FLUSH FLUSH LEVER POSITIONS Timed FLUSH FILL WATER Pull Handle Push Handle The A9 model The A9 model contains an electronic box and functions with wall mounted flush control. Wall mounted Flush Control NORMAL FLUSH Press Normal Flush - starts a timed flush, intake pump starts followed by discharge pump. WATER SAVER FLUSH Press Water Saver Flush starts a timed flush using half the water of a normal flush EMPTY BOWL FLUSH Press and hold Empty Bowl Flush touch pad until all water is removed from bowl. MOMENTARY FLUSH Press and hold Momentary Flush touch pad to flush bowl momentarily. NOTE: To discontinue a timed flush press and release any button. Wall Mounted Flush Control 2

3 Cleaning Instructions IMPORTANT: Do not use cleaners that contain ammonia, ethyl acetate, phosphoric acid or concentrated chlorine bleach. These may cause damage to the toilet. We recommend using Raritan C.P. (#1PCP22), a bio-enzymatic toilet bowl cleaner. Cleaning In-Line Strainer (Sea Water Models only) 1. Shut off intake seacock. 2. Unscrew bowl. 3. Remove filter. 4. Clean bowl and filter, wipe with a clean dry cloth. 5. Clean gasket and gasket contact surfaces thoroughly. 6. Replace gasket, filter and bowl. 7. Open seacock. 8. Check for leaks. Filter Bowl Unscrew C.P. Clean gasket and gasket contact surfaces thoroughly Tighten MAINTENANCE Refilling Optional Atlantes Deodorant System (ADS) Intake pump models only Using Raritan Concentrate (#CON22) helps keep the bowl clean and lubricates internal parts. Pour 8 oz. (237ml) of concentrate into tank and fill with water. 3

4 WINTERIZING IMPORTANT Improper winter lay up is a major cause of marine toilet failure. Use only nontoxic antifreeze. Flush toilet several times to clear waste from system. Dispose of all antifreeze in accordance with local and federal regulations. Winterize holding tanks, plumbing, treatment systems (MSD s), etc. independently following manufacturer s instructions. Pressurized Freshwater Models Parts Required 1 1/2" (38mm) I.D. piece of discharge hose, approximately 3 (1m) long Two buckets Nontoxic antifreeze approximately 1 quart (1 liter). Steps 1. Close discharge seacock. 2. Shut off intake water at source. 3. Turn off power to unit. 4. Disconnect and drain discharge hose. 5. Disconnect intake hose from intake water source and drain. 6. Connect hose to toilet s discharge and place in other bucket. 7. Pour antifreeze in toilet bowl. 8. Turn on power to unit and flush until antifreeze is removed from bowl and water is drained from solenoid valve and hose. 9. Disconnect power to toilet. Nontoxic Antifreeze Pressurized Freshwater Model Atmospheric Vacuum Breaker Discharge Hose Solenoid Valve Intake Water Source Shut Off Valve Allow water to drain into bucket Integral and Remote Intake Pump Models Parts Required 3/4" (19mm) I.D. piece of intake hose approximately 3 (1m) long. 1 1/2" (38mm) I.D. piece of discharge hose approximately 3 (1m) long. Two buckets Nontoxic antifreeze approximately 1 quart (1 liter). 4

5 Sea Water Model (Integral Pump) Sea Water Model (Remote Pump) Nontoxic Antifreeze Steps 1. Close intake and discharge seacocks. 2. Turn off power to unit. 3. Disconnect and drain intake hose, discharge hose and In-Line Strainer. 4. Connect short hoses to toilet s intake and discharge. 5. Place one bucket under hose connected to toilet s discharge. 6. Pour nontoxic antifreeze in other bucket. 7. Place hose connected to intake pump into bucket with antifreeze. 8. Turn on power to unit and flush toilet until antifreeze begins to be discharged from toilet. 9. Disconnect power to toilet. WINTERIZING Nontoxic Antifreeze RECOMMISSIONING 1. Using buckets, hoses and approximately one gallon (3.8 liters) of clean fresh water, flush antifreeze out of the toilet (see Winterizing Instructions). Dispose of antifreeze in accordance with local and federal regulations. 2. Reconnect intake and discharge hoses and open water source valve. 3. Proceed to System Start-Up. SYSTEM START-UP 1. Open seacock(s). NOTE: Pressurized freshwater models; open water source valve. 2. Turn on power to toilet. 3. Flush toilet per Operation Instructions. 4. Check for leaks. 5

6 SPECIFICATIONS Parts Included All Complete Toilets Toilet Bowl Seat and Cover A7 and A8 Model A9 Model - Wall Switch Flush Control Panel Straight Discharge (except -01 models) Vinyl Caps (2) Nylon Shoulder Washer (2) Sea Water Model In-Line Strainer with fittings Intake Pump Pressurized Freshwater Models Solenoid Valve with fittings Atmospheric Vacuum Breaker Additional Parts Required (minimum) Two stainless steel mounting bolts or lag screws (minimum 1/4" [6mm]) and washers) 1 1/2" (38mm) I.D. discharge hose 3/4" (19mm) I.D. reinforced intake hose 3/4" (19mm) hose clamps 1 1/2" (38mm) hose clamps Wire Wire Connectors Fuse/circuit breaker Minimum Tools Required (will depend on fasteners) Screwdrivers Wrenchs Drill bits Jig Saw Wire cutters Wire connector crimpers Hose cutters Tape measure Level Width: 2 3/4" (7cm) Depth of base: Normal: 15" (38cm) Elongated: 18 (46cm) Height: 4 1/2" (11.5 cm) SPECIFICATIONS Width of base: 14" (36cm) Depth of top: Normal bowl: 19 1/2"" (50cm) Elongated bowl: 21 (53.8cm) Height w/ seat and cover: 17 3/" (44cm) 6

7 Plumbing Pressurized water source Maximum suction of intake pump (maximum height above waterline) Maximum height NOTES: for Wiring of discharge vented loop Minimum flow rate - 3 gallons per minute (11.3 liters per minute) Minimum pressure - 5psi (34.5 kpa) 4 ft. (1.2 M) from Intake Pump 6 ft. (1.7 M) from floor 1. Distances are from source to unit and back to source Recommended conductor wire minimum (mm ) for 3% voltage drop Atlantes w/intake pump - Recommended Wire and Fuse/Circuit Breaker Size Units Voltage o Recommended conductor sizes are based on 5 C rated insulation. Refer to ABYC Standards for other insulation ratings. For 0/240 VAC units use 24VDC specifications from transformer to unit. Circuit Breaker/fuse size (amps) Amp. nominal voltage VDC VDC SPECIFICATIONS 32 VDC Branch to Remote intake pump (if used) VDC VDC VDC 14 CONVERSIONS Wire - to mm mm Feet to Meters Feet Meter Atlantes w/solenoid valve - Recommended Wire and Fuse/Circuit Breaker Size Units Voltage Circuit Breaker/fuse size (amps) Amp. nominal voltage VDC VDC VDC

8 INSTALLATION Mounting Toilet Mounting surface must be flat and solid. 1. Install seat on toilet. 2. Place toilet where it will be located. Make sure there is room to route hoses. Make sure seat will open properly. 3. Using a pencil, mark location of bowl mounting holes. 4. A. If hoses will be routed through floor, trace one side of toilet on floor. B. If hoses will be routed through wall, trace one side of toilet on wall. 5. Remove toilet and mark location for hoses on deck or wall. 6. Cut necessary holes using enclosed template through wall or floor. 7. Drill holes for toilet mounting bolts/ screws. NOTE: Use 1/4" [6mm] size bolts/screws. To select proper Screw or Bolt length, measure thickness of deck plus 1 1/8'' (29mm). TIP: Secure toilet to floor after installation is complete. CAUTION: Do Not over tighten mounting bolts. Damage to the toilet bowl may occur. Tighten both mounting bolts evenly and slowly. C A B C D E F A.Vinyl cap - #VCap (supplied) B. 1/4-20 S/S Bolt, or 1/4 S/S Self Tapping Screw, or 1/4 S/S Lag bolt C. Flat Washer, Stainless Steel D. Nylon Shoulder Washer - #F071 (supplied) E. S/S Lock washer (used on top and bottom for Nut and Bolt) F. 1/4-20 S/S Nut 8

9 A9 Models Only Mounting Atlantes Wall Mounted Flush Control IMPORTANT: Locate where wires can be routed. NOTE: The control panel cable length is 14' (427cm) Minimum depth of 2 1/2" (6.3cm) from surface is required. Parts Included Back plate assembly Bezel #4 x 1/2" screws for surface mounting (4) #6-32 x 7/8" screws for receptacle box mounting (2) Gasket Tools Required Flat blade screw driver Level For surface mount 2 1/8" (54mm) hole saw Drill with 5/64" (2mm) drill bit Surface Mounting 1. Attach template provided to mounting surface. Make certain it is level. 2. Drill four 5/64" (2mm) holes. 3. Drill one 2 1/8" (54mm) hole with hole saw. 4. Install gasket on back plate. 5. Connect control panel cable (See Wiring). 6. Secure back plate to surface using #4 x 1/2" screws (4). NOTE: Before securing back plate see J1 Jumper settings for Wall Mounted Flush Control under Changing Flush Times 7. Attach bezel to back plate. Receptacle Box Mounting 1. Cut out surface the size of receptacle box. 2. Mount receptacle box. 3. Install gasket on back plate. 4. Connect control panel cable (See Wiring). 5. Secure back plate to receptacle using #6-32 x 7/8" screws (4). NOTE: Before securing back plate see J1 Jumper settings for Wall Mounted Flush Control under Changing Flush Times 6. Attach bezel to back plate /2" (6.3cm) min. #4 x 1/2" screws #6-32 x 7/8" screws INSTALLATION

10 INSTALLATION Mounting In-Line Strainer (Sea Water Models Only) Make sure strainer bowl is tight. 1. Locate strainer where it will be accessible. 2. Mark and drill mounting holes. NOTE: Minimum 1/4" (6mm) size bolts/screws are recommended. 3. Install fittings provided (PLA14) on strainer s inlet and outlet ports using PTFE tape (included). 4. Mount strainer according to flow marking on strainer top. Mounting Remote Intake Pump (Remote Pump Models Only) 1. Remote intake pump must be mounted on a flat solid surface in an area that is dry and well ventilated. 2. Mark and drill mounting holes. NOTE: Minimum 1/4" (6mm) size bolt/screws are recommended. 3. Mount pump. Do not over tighten bolts. Flow Marking Mounting Water Solenoid Valve (Pressurized Freshwater Models Only) 1. Locate water solenoid valve on a solid flat surface in an area that is dry and well ventilated. 2. Mark and drill holes for water solenoid valve mounting bracket. NOTE: Minimum 1/4" (6mm) size bolt/screws are recommended. 3. Mount bracket. 4. Install fittings provided (PLA14) on water solenoid valve s inlet and outlet ports using PTFE tape (included). 5. Attach water solenoid valve to bracket. Hoses must be installed according to flow markings on valve body. Mounting Atmospheric Vacuum Breaker (Pressurized Freshwater Model only) 1. Install fittings as shown. 2. Locate mounting area that is a minimum of 6" (15.3cm) above toilet. 3. Secure where top is in horizontal position. From Pressurized Freshwater Source IN OUT PLA14 To inlet port of vacuum breaker Min. of 6" (15.3 cm)

11 PLUMBING WARNING: Hazard of Flooding Toilets mounted at or below the waterline must have a vented loop installed in the discharge line. The top of the vented loop must be a minimum of 4" (cm) above the waterline at the boats greatest angle of heel (see vented loop manufacturer s instructions). Sea Water Models must also have a vented loop installed between the intake pump and the toilet bowl. Double clamp all below waterline connections. IMPORTANT Fittings and 90 bends should be kept to a minimum. In-Line Strainer must be installed on Sea Water Models per Installation Instructions. Failure to do so may void Warranty. Discharging untreated sewage is forbidden in all U. S. waters within the three-mile limit. Thru-hull fittings and seacocks must be installed where they are easily accessible. Use only quality reinforced hoses. Secure all hoses properly. To retain water in bowl see section Retaining Bowl Water in installation/wiring section. Atlantes with Integral Pump and Atlantes Deodorant System installed above waterline. Waterline Vented Loop Discharge Seacock Vented Loop Lectra/San Discharge Seacock T-Check Valve must be installed Atlantes with Remote Intake Pump installed below waterline. Vented Loop Lectra/San Remote Intake Pump In-Line Strainer Atlantes In-Line Strainer Vented Loop Atlantes Plastic Tubing Clamp Intake Seacock Intake Seacock Waterline Atlantes Deodorant System Waterline Atlantes with Water Solenoid Valve (#A5F* or A6F*) for water system connection with holding tank. Atmospheric Vacuum Pump Out Breaker INSTALLATION Drawings are not to scale and intended only as a general reference. Discharge Lines 1. Connect quality 11/2 (38mm) I.D. sanitation hose to discharge fitting. 2. Run hose to appropriate Marine Sanitation Device. NOTE: Discharge hose runs longer than (4.9m) should install a vented loop near toilet to force waste beyond vented loop to drain by gravity. Solenoid Valve Waterline Holding Tank 11 Shut-off Valve Atlantes Potable Water Supply Discharge Fitting Discharge Hose 6" (15cm) Min. Waterline

12 INSTALLATION Intake Lines Pressurized Freshwater Models WARNING: Hazard of potable water contamination. An atmospheric (anti-siphon) vacuum breaker must be used with any installation using a potable water source. Install a shut off valve in intake line before water solenoid valve. 1. Connect hose from shut off valve to inlet port of water solenoid valve. NOTE: To avoid malfunction of water solenoid due to debris in water, installation of Freshwater Strainer (190601) is recommended. 2. Connect hose from outlet port of water solenoid valve to inlet port of vacuum breaker. 3. Connect hose from outlet port of vacuum breaker to bowl elbow. NOTE: Vacuum breaker must be last mechanical component before bowl elbow. From Pressurized Freshwater Source (Shut Off Valve) Outlet Port Inlet Port IN OUT To Inlet Port of Vacuum Breaker Sea Water Models Intake pump fittings are interchangeable to allow more flexibility during installation. Inlet ports are located on either side of intake pump. Outlet port (to toilet bowl) is at top of intake pump. 1. Slide fitting clips to open position. 2. Select inlet port to be used. (Integral models - only one port is available) 3. Install appropriate fittings into inlet and outlet ports. NOTE: The 90 fitting can be rotated Install the plug fitting into unused inlet port. (Integral models - plug is pre-installed) IMPORTANT: Be sure not to install plug fitting into outlet port! Damage will occur! 5. Slide fitting clips back to closed position. 6. Connect hose from seacock to inlet port of In- Line Strainer. Use hose clamp provided. 7. Connect hose from outlet port of In-Line Strainer to inlet port of intake pump. Use hose clamp provided. IMPORTANT: Double clamp all below waterline hose connections! Remote Pump Models - Connect hose from outlet port of intake pump to bowl elbow located on back of toilet bowl. (Integral pump model is Open Outlet Port Arrow Inlet Ports Closed To Bowl From Seacock From Strainer Plug To Intake Pump

13 already connected). WIRING WARNING: Hazard of Shock and Fire Always use proper wire and fuse/circuit breaker. See Specification Chart. Secure wire properly. Do not connect appliances to toilet circuit. Make sure power is off before proceeding. Use proper wire terminals for all wire connections. 1. Determine proper wire size by measuring distance from power source to toilet motor back to power source. 2. Select proper gauge wire and fuse/circuit breaker size from Specifications. 3. Install fuse/circuit breaker in positive line at source. 4. Connect positive wire from fuse/circuit breaker to red (POS) at rear of bowl. 5. Connect wire from battery negative or power source ground buss to black (NEG) at rear of bowl. Remote Intake Pump: Connect red and black 8 wire at back of bowl labeled remote pump - red wire (POS) to orange wire and black wire (NEG) to black wire of remote intake pump. Red Battery POS Black Battery NEG Red Battery POS Black Battery NEG T-check Valve (In-Line) Black Red Black Org Remote Intake Pump INSTALLATION / WIRING Pressurized Freshwater Solenoid Valve: Connect black and orange wire from back of bowl to water solenoid valve. Water solenoid is not polarity sensitive. 0/240 VAC Units: For proper wire gauge and circuit breaker from Transformer (#RTAH24D) to unit refer to 24 VDC specifications. To connect power to transformer refer to Installation Instructions included with #RTAH24D. Red Battery POS Black Battery NEG Orange Black Solenoid Valve Atlantes with Wall mounted Flush Control Panel (A9 Models): Unroll cable from toilet control and route to opening on the wall. Attach cable to the back of Atlantes Wall mounted Flush Control Panel. Secure cable every 18 inches (46cm). Do not damage insulation. Toilet Control 13

14 Flush Lever Toilets (A8 Models): NOTE: A discharge vented loop MUST be installed to retain water in the bowl. To retain water in bowl turn extend flush switch ON (located on Toilet Control). Inlet pump will continue to run a few seconds after discharge pump has stopped. Unit with factory installed internal vented loop is preset to ON position. CHANGING FLUSH TIMES Flush Lever Toilets (A8 Models): The normal flush is factory pre-set for approximately seconds. Installations that require longer flush times can be changed by setting switch number 2 and 3 per flush time adjustment chart Retaining Bowl Water Wall Switch Flush Control Panel (A9 Models): NOTE: A discharge vented loop MUST be installed to retain water in the bowl. To retain water in bowl set switch 1 of J1 to ON. Intake pump will continue to run a few seconds after discharge pump has stopped. Changing Flush Time Wall Switch Flush Control Panel (A9 Models): Normal flush can be set to flush for,, 14 or seconds by setting switches 2 and 3 located behind the wall switch flush control panel. Water Saver Flush will be half of the time set by these jumpers. INSTALLATION \ WIRINGRetaining Bowl Water Adjusting the flush time can be done from either the Toilet Control or from the Wall Switch. However, one must to be set to off and then flush times can be adjusted. Having both set to on will cause one to override the other. For ease of changing settings, it is suggested that the Flush Control be set to off and adjustments be made from the rear of the wall swith. If you wish to insure that water comes into the bowl at the end of the flush, be sure to set switch 1 to the on position. Toilet Control $1*( 72,/(7 &21752/ 5$5,7$1 )520 /67,17$.( %/8( 72 /67 ',6&+ :+,7( )/86+&21752/ 3$1(/ 1(* %/$&. (;7(1')/ )) )/86+7,0( Flush Time Adjustment J1 Switch Settings SWITCH NUMBER 2 3 ON ON OFF FLUSH TIME SECONDS ON OFF ON 14 OFF OFF 14

15 Upgrading from A7 to A8: 1. Turn off power 2. Remove mounting screws and slide bowl forward slightly 3. Locate and gently pull the 4 wires for the toilet control leaving some slack to make connections 4. Install all four wires on toilet control following the correct color code 5. Set timer to desired settings - see changing flush times 6. Check operation by turning on power 7. Install box in place by pressing firmly reclosable fastner 8. Mount the bowl INSTALLATION / WIRING 15

16 TROUBLESHOOTING Unit does not activate or flush: No power to unit Check main circuit breaker/switch check wiring to unit Overload/jammed discharge Reset A9 model by turning off power if unit runs for few second only and stops again see how to clear jam/clog Unit runs as soon as power is turned on: Reversed polarity Check and correct polarity Stuck handle Make sure handle is not stuck in on position Failed timer control Disconnect timer control and check Bowl does (see replacing not retain timer) water: A vented loop (external or internal is required to retain water in the bowl) Check jumper settings for extended flush Clogged vent check and clear vent in the loop Water in the vent line ventline must be run to avoid dips or low Poor spots or no flow from rim of the bowl: Clogged intake strainer check and clean strainer basket Air leak in suction line repair No activation of inlet pump/solenoid Check if pump or solenoid has power replace or repair if power but no activation Bowl fills up/ poor discharge out of bowl Low voltage below 11.5V Clogged discharge pump See how to clear Jam/clog Clogged discharge line/clogged vent check and repair Failed water solenoid Check if water solenoid shuts off completely, repair if needed Replacing/checking toilet control: 1. Turn off power 2. Remove mounting screw and slide bowl forward slightly 3. Remove control from reclosable fastner 4. Pull box out until all wires are accessible 5. Disconnect wires using needle nose pliers, do not pull on wires, pull connectors 6. Install new control 7. Check operation by turning on power 8. Install box in place by pressing firmly on reclosable fastner 9. Mount the bowl How to clear Jam/clog A7 Model: Disconnect POS and NEG wires at battery Note: Do not disconnect any wires at toilet control box Connect NEG to POS and POS to NEG Push handle back until discharge starts to run Repeat several times, this causes motor to run in reverse and should clear most clog s Reconnect NEG to NEG and POS to POS A8 and A9 models: Disconnect POS and NEG wires at battery Note: Do not disconnect any wires at toilet control box Connect NEG wire to POS from battery MOMENTARILY connect POS from toilet to NEG from battery until discharge starts running Reconnect NEG to NEG and POS to POS Tip for Removing Intake Pump Plug Set screw must be loosened with 1/8" hex key before removing the intake pump from motor

17 F7 AM660W AM661 F147VT 22B 501*W (A8) 502*W (A9) AM667 AM666 AM662 AM660 AM664 AM663 36AW CH43 AM519 CH43 TOILET CONTROL - MODELS A8 AND A9 22AW C254 AM141 AM140 F148VT WALL MOUNTED FLUSH CONTROL E AM130A F5NP AM031 F6 AM114 AM2 F W SOLENOID VALVE PLA14 CWPS*A ATW640+ CWPSMB AM030+ AL030+ (elongated) M23A CH20B F4 24 F145VT AM1 AM1 AM028 F089 ETB3 F W 2420 PLA AM001+ AL001+ (elongated bowl) F M23A 2135 F2VT F ATMOSPHERIC VACUUM BREAKER PLA13 AM665 F111 M23A AM601* F089 AM5 26B 60*A 1118 F035 F A 2305 PLA14 PLAVB0-5 F1 AM515 F W EXPLODED PARTS 1118 F M23A F143VT HSBI RNI M31 M31 M30 HLWQB F069 AM020B W (optional) SEA WATER STRAINER ASSEMBLY 3000 Optional T-Check Valve Optional Deodorant System D W CH CH E D W W G C H F

18 PARTS LIST PART # DESCRIPTION 1118 (4) 1/4" Locking Star Washer 1119 (2) 1/4-20 x 3/4 Hex screw 22AW 90 Discharge w/flange 22B Straight Discharge 26B (2) 1/4-20 Nut S/S 36AW Spud Assembly 36E Bowl Elbow 20W Upper Housing Assembly 2135 (4) Cone Seal 2200W Middle Housing Assembly 2225 O-Ring 2300W Lower Housing Assembly 2305 Lower Housing 23 Diaphragm 2315 Piston (4) 2320 Piston Seat (4) 2325A Bearing Plate Assembly /4" Hose Barb 90 Fitting 24 3/4" Hose Barb Straight 2415 Plug Fitting 2420 (3) Fitting Clip 2425 (3) O-Ring 60*A Pump Motor 31-2 Motor Shaft Seal Bowl Elbow (Freshwater Units not shown) AM001+ Atlantes Bowl (white) AL001+ Atlantes Elongated Bowl (white) AL030+ Atlantes Elongated Seat and Cover (white) AM020B Pump Mounting Bracket AM028 (2) Bushing AM030+ Atlantes Seat & Cover (white) AM031 Discharge Connection (3 pieces) AM1 Discharge Pump Back AM114 Discharge Pump "0" Ring AM130A Discharge Pump Body AM140 Discharge Cover AM141 Discharge Cover O-Ring AM1 Grinder Impeller AM2 Grinder Teeth AM5 Terminal Block Bracket AM203 Remote Inlet Pump Base (not shown) AM515 Atlantes Pump Mounting Bracket AM519 Intake Hose from diaphragm pump AM601* Discharge Motor C254 Joker Valve CH20B # SS Flat Washer CH43 (2) Hose Clamp S/S ETB3 Terminal Block F005 (2) 1/4-20 x 5/ SS Hex Socket Set Screw F035 (3) Isolation Nut F069 (2) 1/4" Fiber Washer F071 Nylon Shoulder Washer (not shown) F089 (3) 1/4-20 x 1 3/4" Rnd. Hd. Screw S/S F4 Panel Nut Brass Hex 5/8-32 x 7/8 x 1/8 F5NP (2) 1/4-28 set screw with nylon patch F6 (2) Plastite screw #6 x 3/4 F8 (2) Screw #4 x 7/8 F111 (4) -32 S/S Nut F1 (2) 8-32 x 1/4 Screw F142VT (8) -32 x 5/8" Pan Hd. S/S Screw (not shown) F143VT (2) -32 x 1" Pan Hd. SLTD S/S Screw F144 (6) # S/S Flat Washer F145VT -32 x 1 3/4" Pan Hd. SLTD S/S Screw F146VT (2) 1/4-20 x 1 1/4" Rnd Hd. Screw S/S W/VT F147VT (2) 3/8- x 1 1/2" Rnd Hd. Screw S/S F148VT (8) 8-32 x 7/" S/S Truss Hd. Screw F2VT (4) Mounting Bolt F172 (4) Plastite Screw # x 1/2 HLWQB (4) 1/4" Split Lock Washer HSB1 (2) 1/4-20 Brass Screw M23A (19) # Lockwasher S/S M30 (4) 1/4-20 Brass Nut M31 (8) 1/4" Brass Flat Washer RNI (2) Nylon Shoulder Washer VCAP (2) Vinyl Cap (screw head covers - not shown) 18 LEVER FLUSH CONTROL (A7 and A8 Series) AM600W Flush Switch Assembly, w/wire harness F7 (5) #4 x 1/4 Phlps. Pan Hd. Screw S/S AM660 Enclosure AM661 Cover AM662 Lever (internal) AM663 Enclosure Bushing AM664 Handle Shaft AM665 Flush Handle, S/S AM666 Spring AM667 (2) Snap Action Switch AM668 (2) Clip Bearing (not shown) WALL MOUNTED FLUSH CONTROL (A9 Series) 26A 1/4-20 X 1 1/4 Rnd. Hd. Screw S/S Cable for Flush Control (14 ft.) AM028 Bushing AM6W Flush Control wire harness assembly ATW* Flush Control PCB Assy. ATW640 Flush Control with Bezel Back Plate (White) ATW640A Flush Control with Bezel Back Plate (Bone) ATW640B Flush Control with Bezel Back Plate (Black) F153 #4 1/2 Oval slotted F170 6/32-7/8 screw OTHER PARTS 300 Swawater Strainer Assembly AM019S Silicone Cap, used on A9 only, in place of Flush lever (not shown) AJ138 Nylon Washer, used on A9 only (not shown) SOLENOID VALVE CWPS*A 1/2" GC Solenoid Valve CWPSMB Mounting Bracket for CWPS* PLA14 (2) 1/2" MPT to 3/4" Barbed Nipple ATMOSPHERIC (ANTI-SIPHON) VACUUM BREAKER PLA13 1/2" NPT to 3/4" Hose Elbow PLA14 1/2" MPT to 3/4" Barbed Nipple PLAVB0-5 Atmospheric (anti-siphon) Vacuum Breaker OPTIONAL T-CHECK VALVE PARTS LIST D Valve Body D1 Outlet Adapter E O Ring W T-Check Valve Assembly Complete W Siphon Check Valve CH8 Check Valve Spring CH Check Ball OPTIONAL DEODORANT/SALT FEED PARTS LIST (ADS) Salt Feed Tank Salt Feed Tank Cap C Plastic Tubing Clamp F Bulkhead Fitting G Bulkhead Fitting Nut H Bulkhead Fitting Seal W Assembly (includes part #'s C, F, G, H, ) PVC Clear Tubing 1/4" ADDITIONAL ACCESSORIES AVAILABLE FROM RARITAN 1PCP22 C.P., Cleans Potties, Bio-enzymatic toilet cleaner, 22 oz. bottle AHDA1W Internal Vented Loop CON22 Raritan Concentrate 22 oz. bottle SH Sanitation Hose (sold by the foot) VL 1 1/2 Vented Loop 1 1/2" VL 3/4 Vented Loop 3/4" YV "Y" Valve RTAH24DA Trnsfrmr./Rctfr. for 0/240 VAC (not shown) Parts are NOT included with Wall Switch Flush Control Models +CHOICE OF COLOR *SPECIFY VOLTAGE

19 19 NOTES

20 LIMITED WARRANTY Raritan Engineering Company warrants to the original purchaser that this product is free of defects in materials or workmanship for a period of one year from the product s date of purchase. Should this product prove defective by reason of improper workmanship and/or materials within the warranty period, Raritan shall, at its sole option, repair or replace the product. 1. TO OBTAIN WARRANTY SERVICE, Consumer must deliver the product prepaid, together with a detailed description of the problem, to Raritan at 530 Orange St., Millville, N.J , or 31 SW 2nd Ave. Ft. Lauderdale, FL When requesting warranty service, purchaser must present a sales slip or other document which establishes proof of purchase. THE RETURN OF THE OWNER REGISTRA- TION CARD IS NOT A CONDITION PRECEDENT OF WARRANTY COVERAGE. However, please complete and return the owner Registration Card so that Raritan can contact you should a question of safety arise which could affect you. 2. THIS WARRANTY DOES NOT COVER defects caused by modifications, alterations, repairs or service of this product by anyone other than Raritan; defects in materials or workmanship supplied by others in the process of installation of this product; defects caused by installation of this product other than in accordance with the manufacturer s recommended installation instructions or standard industry procedures; physical abuse to, or misuse of, this product. This warranty also does not cover damages to equipment caused by fire, flood, external water, excessive corrosion or Act of God. 3. ANY EXPRESS WARRANTY NOT PROVIDED HEREIN, AND ANY REMEDY FOR BREACH OF CONTRACT WHICH BUT FOR THIS PROVISION MIGHT ARISE BY IMPLICATION OR OPERATION OF LAW, IS HEREBY EXCLUDED AND DISCLAIMED. ALL IMPLIED WARRAN- TIES SUCH AS THOSE OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE, IF APPLICABLE, AS WELL AS ANY IMPLIED WARRANTIES WHICH MIGHT ARISE BY IMPLICATION OF LAW, ARE EXPRESSLY LIMITED TO A TERM OF ONE YEAR. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG A LIMITED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. 4. UNDER NO CIRCUMSTANCES SHALL RARITAN BE LIABLE TO PURCHASER OR ANY OTHER PERSONS FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER ARIS- ING OUT OF BREACH OF WARRANTY, BREACH OF CONTRACT, OR OTHERWISE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSE- QUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU 5. No other person or entity is authorized to make any express warranty, promise or affirmation of fact or to assume any other liability on behalf of Raritan in connection with its products except as specifically set forth in this warranty. 6. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. L kgs Specifications Subject to Change Without Notice Printed in USA Orange Street Millville, NJ USA Telephone: FAX: SW Second Avenue, Fort Lauderdale, FL USA Telephone: FAX: