Ladder Rack System. Cable Pathway Cable Runway and Accessories

Transcription

1 Spec Cable Pathway Cable Runway and Accessories Ladder Rack System INDUSTRY STANDARDS Painted and Plated Straight Sections: UL/ for Equipment Grounding and Load; File No. E23644 Curved Sections and Splice Kits: UL/ for Equipment Grounding; File No. E23644 culus Bonding & Grounding Classified as suitable for an equipment ground conductor - CSA C22.2 No Section Load Destruction Test Two grounding jumper kits required per each splice kit on painted ladder rack sections culus Load Testing Load capacity per 0 support lengths is lb.; safety factor of.5x - CSA C22.2 No Section 5. Electrical Continuity Test APPLICATION The Ladder Rack System conveniently routes cables via a modular pathway through unused space on the floor, wall or ceiling while keeping cables accessible for easy maintenance. A variety of straight and curved sections are highly adaptable and can accommodate virtually any room layout. FEATURES Section cross members welded on 9-in. (229-mm) centers Accessory adjustable cross members Butt-splice kits and junction-splice kits Each model is boxed or bagged SPECIFICATIONS Straight and curved sections made of -/2-in. steel Sections available in 6-, 2-, 5-, 8- and 24-in. (52-, 305-, 38-, 457- and 60-mm) widths Steel connecting and mounting hardware FINISH Available in four finishes: ANSI 6 gray polyester powder paint RAL 9005 black polyester powder paint White powder paint Plated ACCESSORIES Touch-up Paint Networking SUBJECT TO CHANGE WITHOUT NOTICE EQUIPMENT PROTECTION

2 Ladder Rack Straight Sections Supports cable on straight runs. Made of -/2 in. x 3/8 in. (38 mm x 8 mm) 6 gauge tubular steel with a painted or plated finish. Nominal installed length is 0 ft. (3.05 m). Each section is 9 ft. -/2 in. (3.03 m) long with cross members welded at 9-in. (229-mm) intervals., DOFRC Finish W (in.) W (mm) LSS6G Gray LSS6BLK Black LSS6GZ Plated LSS6W White LSS2G Gray LSS2BLK Black LSS2GZ Plated LSS2W White LSS5W White LSS5BLK Black LSS8G Gray LSS8BLK Black LSS8W White LSS8GZ Plated LSS24BLK Black LSS24W White Butt-Splice Kit Joins straight ladder rack sections, inside and outside bends, and 90-degree horizontal e-bends. Each kit connects one section to another. Includes mounting hardware. Finish Kit Qty. LBSKG Gray 2 LBSKB Black 2 LBSK Plated 2 LBSKW White 2 Adjustable Butt-Splice Kit Provides a change in up-and-down direction of the cable runway. It can be adjusted to any angle from 0 to 90 degrees. Made of steel with a painted or plated finish. Each kit connects one ladder rack section to another. Includes mounting hardware. Finish Kit Qty. LABSKG Gray 2 LABSKB Black 2 LABSK Plated 2 LABSKW White 2 EQUIPMENT PROTECTION PH FAX pentairprotect.com Networking 2

3 Ladder Rack Curved Sections Provide a vertical change in direction. They are made of -/2 in. x 3/8 in. (38 mm x 8 mm) tubular steel with a painted or plated finish. Cross members are welded on the inside (inside bends) or outside (outside bends) of the section. Connect to straight section with butt-splice kits. Designed for category 5e, 6, 6A and fiber optic cable., DOFRC Finish Vertical Bend Type W (in.) W (mm) LIB6G Gray Inside LIB6BLK Black Inside LIB6GZ Plated Inside LIB6W White Inside LIB2G Gray Inside LIB2BLK Black Inside LIB2GZ Plated Inside LIB2W White Inside LIB5BLK Black Inside LIB5W White Inside LIB8G Gray Inside LIB8BLK Black Inside LIB8W White Inside LIB8GZ Plated Inside LIB24BLK Black Inside LIB24W White Inside LOB6G Gray Outside LOB6BLK Black Outside LOB6GZ Plated Outside LOB6W White Outside LOB2G Gray Outside LOB2BLK Black Outside LOB2GZ Plated Outside LOB2W White Outside LOB5BLK Black Outside LOB5W White Outside LOB8G Gray Outside LOB8BLK Black Outside LOB8GZ Plated Outside LOB8W White Outside LOB24BLK Black Outside LOB24W White Outside Degree Horizontal E-Bend Section Provide a 90-degree horizontal change in cable runway direction. Made of -/2 in. x 3/8 in. (38 mm x 8 mm) tubular steel with a painted or plated finish. Connect to straight sections with butt-splice kits. Designed for category 5e, 6, 6A and fiber optic cable., DOFRC Finish W (in.) W (mm) L90HB2G Gray L90HB2BLK Black L90HB2GZ Plated L90HB2W White L90HB5BLK Black L90HB5W White L90HB8G Gray L90HB8BLK Black L90HB8GZ Plated L90HB8W White L90HB24BLK Black L90HB24W White Networking SUBJECT TO CHANGE WITHOUT NOTICE EQUIPMENT PROTECTION

4 Junction Splice Kit Connects two straight ladder rack sections at a 90-degree angle. Made of steel with a painted or plated finish. Each kit connects one section to another. Includes mounting hardware. Finish Kit Qty. LJSKG Gray 2 LJSKB Black 2 LJSK Plated 2 LJSKW White 2 Adjustable Junction Splice Kit Connects two ladder rack sections at any junction angle. Made of steel with a painted or plated finish. Each kit connects one section to another. Includes mounting hardware. Finish Kit Qty. LAJSKG Gray 2 LAJSKB Black 2 LAJSK Plated 2 LAJSKW White 2 Retaining Post Kit Provides extra ladder rack capacity. Mounts onto rack side stringer. Post is unthreaded /2-in. tube. Kit components are plated steel. Includes post cap and mounting hardware. Finish Kit Qty. LRP Plated LRPB Black LRPW White L-Bracket Kit The L-Bracket Kit supports power or other cables that need to be separated from the main cable run. Made of steel with a painted or plated finish. Mounts onto ladder rack stringer. Includes mounting hardware. Finish Kit Qty. LLBG Gray LLBB Black LLB Plated LLBW White EQUIPMENT PROTECTION PH FAX pentairprotect.com Networking 4

5 Radius Drop Kit Mounts over ladder rack cross member to provide bending radius when dropping cable. Includes cable spools to separate cable and all mounting hardware. Made of extruded aluminum. Cable Runway Width (in.) Cable Runway Width(mm) Finish LRD6G Gray LRD6BLK Black LRD6GZ Aluminum LRD6W White LRD2G Gray LRD2BLK Black LRD2GZ Aluminum LRD2W White LRD5BLK Black LRD5W White LRD8G Gray LRD8BLK Black LRD8GZ Aluminum LRD8W White LRD24BLK Black LRD24W White Kit Qty. Stringer Radius Drop Kit Mounts over ladder rack stringer to provide bending radius when dropping cable. Includes cable spools to separate cable and all mounting hardware. Made of extruded aluminum. Finish Kit Qty. LSRDG Gray LSRDBLK Black LSRDW White Foot Kit Secures ladder rack to floor, ceiling or wall. Made of steel with a painted or plated finish. One kit secures one ladder rack section. Requires surface mounting hardware (not included). Finish Kit Qty. LFKG Gray 2 LFKB Black 2 LFK Plated 2 LFKW White 2 5 Networking SUBJECT TO CHANGE WITHOUT NOTICE EQUIPMENT PROTECTION

6 Ceiling Support Kit Supports ladder rack from ceiling. Components available separately or as a kit. Six-foot-long, 5/8-in. diameter rod is threaded for easy tension adjustment. Made of plated steel. Requires surface mounting hardware (not included). LRWSBK Finish Description Kit Qty. LCK Plated Kit includes one each: - LTR Threaded Rod - 5/8-in. nuts (4) - LRWBK Rack Runway Bracket - LCBK Ceiling Bracket LTR Plated 5/8-in. x 6-ft. Threaded Rod LRWBK Plated Rack Runway Brackets (0) 5/8-in. nuts (20) LRWBKB Black Rack Runway Brackets (0) 5/8-in. nuts (20) LRWBKW White Rack Runway Brackets (0) 5/8-in. nuts (20) LCBK Plated Ceiling Brackets (0) 5/8-in nuts (20) LCBKB Black Ceiling Brackets (0) 5/8-in nuts (20) LCBKW White Ceiling Brackets (0) 5/8-in nuts (20) LRWSBK Plated Rack-to-Runway Brackets (0) Slip-On 5/8 in. nuts (20) LRWSBKB Black Rack-to-Runway Brackets (20) Slip-On 5/8 in. nuts (40) LRWSBKW White Rack-to-Runway Brackets (20) Slip-On 5/8 in. nuts (40) Rack-to-Runway Mounting Plate Kit Secures ladder rack to the top of equipment racks. Made of steel with a painted or plated finish. The plate is designed for mounting either parallel or perpendicular to the rack. Includes mounting hardware. Fits Ladder Width Finish Kit Qty. LRRMPG 6, 2 Gray LRRMPBLK 6, 2 Black LRRMPGZ 6, 2 Plated LRRMPW 6, 2 White LRRMPW5 2, 5 White LRRMPBLK5 2, 5 Black LRRMPG8 2, 8 Gray LRRMPBLK8 2, 8 Black LRRMPGZ8 2, 8 Plated LRRMPW8 2, 8 White LRRMPBLK24 8, 24 Black LRRMPW24 8, 24 White EQUIPMENT PROTECTION PH FAX pentairprotect.com Networking 6

7 Vertical Wall Bracket Secures ladder rack section to wall or other flat surface. Made of steel with a painted or plated finish. Requires surface mounting hardware (not included). Finish Kit Qty. LVWBG Gray 2 LVWBB Black 2 LVWB Plated 2 LVWW White 2 Triangle Support Bracket Kit Finish Fits Cable Runway Kit Qty. LTSB2G Gray 6, 2 LTSB2BLK Black 6, 2 LTSB2GZ Plated 6, 2 LTSB2W White 6, 2 LTSB8524W White 5, 8, 24 LTSB5824BLK Black 5, 8, 24 LTSB8G Gray 2, 8 LTSB8BLK Black 2, 8 LTSB8GZ Plated 2, 8 LTSB24BLK Black 2, 8, 24 Supports ladder rack from wall. Bracket is made of steel with painted or plated finish. Brackets have predrilled mounting holes for two sizes of ladder rack. Includes one J-Bolt Kit. 7 Networking SUBJECT TO CHANGE WITHOUT NOTICE EQUIPMENT PROTECTION

8 Modular Triangle Support Bracket Kit Secures and supports ladder rack to wall. Design features three bracket support arms that easily attach to each other with quick-release pins and fold down to ease assembly. Each model accomodates two ladder rack widths. Kit includes one modular bracket assembly, three quick-release pins and two J-bolts with washers and nuts. Bracket made of painted steel with plated hardware. Finish Fits Cable Runway Kit Qty. LMTSB2B Black 6, 2 LMTSB2W White 6, 2 LMTSB8B Black 2, 8 LMTSB8W White 2, 8 LMTSB24B Black 8, 24 LMTSB24W White 8, 24 Wall Angle Support Supports ladder rack from wall or other flat surface. Made of 2-in. x 2-in. 0 gauge steel angle with painted or plated finish. Includes two J-bolts, nuts and screws. Finish L in./mm LWASK6G Gray LWASK6BLK Black LWASK6GZ Plated LWASK2G Gray LWASK2BLK Black LWASK2GZ Plated LWASK2W White LWASK5W Whtie LWASK5BLK Black LWASK8G Gray LWASK8BLK Black LWASK8GZ Plated LWASK8W White LWASK24BLK Black LWASK24W White R in./mm S in./mm Kit Qty. EQUIPMENT PROTECTION PH FAX pentairprotect.com Networking 8

9 Corner Support Bracket Kit Provides additional support for 90-degree ladder rack junction. Made of steel with a painted or plated finish. Kit Qty. Finish LCSKG Gray LCSKB Black LCSK Plated LCSKW White End Cap Kit Provides protective covering for ends of ladder rack. Made of black vinyl. Kit Qty. LEC 2 Runway Termination Kit Provides a solid termination when the last section of ladder rack ends away from a wall. Made of steel with a painted or plated finish. Finish Fits Cable Runway Kit Qty. LRTK2G Gray 2 LRTK2B Black 2 LRTK2 Plated 2 LRTK2W White 2 LRTK8G Gray 8 LRTK8B Black 8 LRTK8 Plated 8 LRTK8W White 8 LRTK24B Black 24 LRTK24W White 24 Movable Cross Member Supports cable at drop locations between welded cross members. Made of steel with a painted or plated finish. Includes hardware for secure mounting to ladder rack stringers. Finish W (in.) W (mm) Kit Qty. LMCM2G Gray LMCM2BLK Black LMCM2GZ Plated LMCM2W White LMCM8G Gray LMCM8BLK Black LMCM8GZ Plated LMCM8W White LMCM24BLK Black LMCM24W White Networking SUBJECT TO CHANGE WITHOUT NOTICE EQUIPMENT PROTECTION

10 Rack-to-Wall Kit Includes one section of straight ladder rack and everything needed to fasten the ladder section to an open frame rack and to the wall. Ladder is 54-in. (372-mm) long by 2-in. (305-mm) wide. All parts have a black painted finish. Order open frame rack separately. Bulletin: DOFR2 E45RUBKIT * Ladder Rack is Description Each Rack-to-Wall Kit includes one: - LSS2BLK [54-in. (372-mm) long] Ladder Rack* - LWASK2BLK Wall Angle Support with j-bolts - LRRMPBLK Rack-to-Runway Mounting Kit - LEC End Cap Kit Runway Elevation Kit Elevates ladder rack 3 or 6 in. (76 or 52 mm) above rack-toladder mounting plate. Use on any width ladder rack. Kit includes two brackets and all mounting hardware. Made of heavy plated steel. A (in.) A (mm) Finish Kit Qty. LEK Plated LEK3B Black LEK3W White LEK Plated LEK6B Black LEK6W White LEK Plated LEK2B Black LEK2W White Runway Overhead 2-in. Stack Kit Allows stacking any width of ladder rack runways 2 in. (305 mm) above each other. Each kit contains two complete stacking brackets with all necessary hardware. Use one kit at least every 5 ft. (.5 m). Brackets and fasteners made of plated steel. Finish Includes Kit Qty. LST2 Plated 2 brackets and hardware LST2B Black 2 brackets and hardware LST2W White 2 brackets and hardware EQUIPMENT PROTECTION PH FAX pentairprotect.com Networking 0

11 Runway Center Support Kit Threaded rod and bracket supports center of ladder rack from ceiling. Kit includes heavy-duty ladder rack cross member, two mounting brackets, two #2-24 screws, 5/8-in. threaded rod, protected sleeve and four 5/8-in. nuts. Use one kit at least every 5 ft. (.5 m). Made of plated steel. Finish Fits Cable Runway Kit Qty. LCSK6 Plated 6 LCSK2 Plated 2 LCSK8 Plated 8 LCSK24 Plated 24 Spool Divider Kit Spools separate cables to improve cable management and to control cable-to-cable distances. Spool and bracket attach to ladder rack cross member and can be located anywhere across the width. Kit includes ten 4-in.-tall spools, brackets and all necessary hardware. Spool made of black plastic and bracket made of plated steel. Finish Kit Includes LCRDSK Black plastic spool; plated steel bracket 0 spools, 0 brackets and mounting hardware Insulated Ground Jumper Kit Fastens across splices to provide a secure ground between sections of ladder rack. Made of #6 AWG x 7 strand wire with green THW insulation and two-hole compression lugs mounted on each end. Includes fasteners. Bulletin: DBG Conductor Type L in./mm DGJ #6-7 Stranded culus requires 2 kits per splice on all painted ladder sections Networking SUBJECT TO CHANGE WITHOUT NOTICE EQUIPMENT PROTECTION

12 J-Bolt Kit Connects ladder rack to top of cabinet or to auxiliary support channel. Each kit includes two J-bolts and makes one support connection. Kit components are plated steel. Includes mounting hardware. Each kit contains: (2) J-Bolts, 5/6 in. (2) Nuts, 5/6 in. (2) Washers, 5/6 in. (2) Lock Washers, 5/6 in. () Plate J (in.) J (mm) Finish LJBK Plated LJBK Plated LJBK Plated LJBK Plated CABLERACK Standard Product AxBxC in./mm Rack Units Cable Bend Radius Accessory E9T6U 2.44 x 20.6 x x 52 x ECMBA4 CABLERACK is used for ladder or basket tray mounting and securing 9-inch rack equipment for server rooms, telecommunication rooms, and other applications. The fixed, open frame rack allows suspending 9-inch rack equipment from Ladder Rack or Basket Tray. The rack has universal tapped holes per industry standards to accommodate typical applications. These open frame racks are ideal for high-density cabling applications which require above-the-cabinet mounting of equipment, and provide maximum access to cables and equipment. In applications where equipment expands above the cabinet, CABLERACK provides ideal management with increased equipment and cable densities. Bulletin: DOFRW EQUIPMENT PROTECTION PH FAX pentairprotect.com Networking 2