LED Wall Tile Instruction

Transcription

1 Instruction

2 Contents Product Brief Installation Fittings Construction Troubleshooting P3 P4-P6 P6 P7 P8

3 Product Brief 1 2 Dimension(mm) Current Voltage V Luminous Area m² SL LWT White:0.5W SL LWT White:1.0W SL LWT 1220 SL LWT 240 S SL LWT 730 S SL LWT 1220 S White:1.5W White:0.5W RGB:1.5W White:1.0W RGB:3.0W White:1.5W RGB:4.5W White: RGB: White: RGB:0.125 White: RGB: Example Wall Natural Wall Tile LED Wall Tile Embedded Cable Box SL LWT H2 SL LWT S H2 Wall Wall

4 Installation 2 1 6mm 1 Drill 4 holes on the wall ( φ6mm X H28mm). 2 The hole spacing should strictly follow the data on the left form. 3 Insert M6*25mm pentagons plastic wall plug anchor into the holes SL LWB 240 / S SL LWB 730 / S SL LWB 1220 / S Aim the mounting brackets at the holes. 2 Tighten the brackets with M4 stainless steel flat head self-tapping screws. 3 Calibrate the brackets with tile module, ensuring the installation accuracy. 3 1 Align the left end of the LED wall tile with the left end of the bracket, push it in firmly and align it with the brackets. (LED wall tile can be installed/moved by adjusting one side s angle) 4

5 Installation 4 Inject neutral silicone sealant around the brackets. 5 SL LWT SL LWT S 3 Yellow/ Green SIGNAL Lamps wire outlet & specification: bare wire, 3C copper stranded wire, φ0.5mm²,pvc. (Lamps wire outlet & specification should be chosen on a case-to-case basis, please consult our technicians if necessary) 6 Recommended Wiring 1 Sort out the wires 3 Srew the terminal 2 Set all cores together 4 Seal with neutral silicone sealant 5

6 A Wiring Embedded Cable Box Installation&Fittings The wire specifications should be chosen based on calculation of actual maximum power and reserved appropriate margin, please consult our technicians if necessary. Terminals should be waterproofed B Wiring Embedded Cable Box The wire specifications should be chosen based on calculation of actual maximum power and reserved appropriate margin, please consult our technicians if necessary. Terminals should be waterproofed 3 Yellow/ Green SIGNAL Fittings Product SL LWT SL LWT S Factory Fittings Brackets*2PCS Brackets*2PCS Other Fittings (purchased by customer) M4*20mm Stainless Steel Flat Head Self-Tapping Screws *4PCS M6*25mm Plastic Wall Plug Anchor *4PCS P1 Terminal *2PCS Neutral Silicone Sealant M4*20mm Stainless Steel Flat Head Self-Tapping Screws *4PCS M6*25mm Plastic Wall Plug Anchor *4PCS P1 Terminal *2PCS Neutral Silicone Sealant 6

7 Construction Construction Instruction 1. Welding or terminal connection is advisable for lamps' wiring. The wiring should be chosen according to the actual field condition, the following table is for reference; 2. The specification of embedded wire should be chosen according to the actual field condition, the following table is for reference; Circuit Design Parallel Connection Series Connection Single Lines Total Power (W) < -150 < -150 Embedded Wire s Diameter(mm²) Lamp Wiring Welding or Terminal Connection Welding Welding or Terminal Connection Welding 3. The resistance between the first lamp to power supply should be less than 0.2Ω(in plus out); 4. The distribution box should have power reservation, 50% is recommended; 5. The voltage of the power line shall not be less than 21V a fter line loss; 6. IP67 rating insulation protection is required at the junction of welding or terminal connection; 7. IP67 rating insulation protection is required if there is bare wire from the last lamp; 8. Well place the lamps during construction to avoid smashing since the lamps use tempered glass raw material and sandwich structure. WARNING 7

8 Troubleshooting Troubleshooting 1. If there are troubles when testing lamps on side, refer to the below table for troubleshooting. Trouble Single lamp fails to light up Single lamp fails to be controlled Most lamps fail to light up Most lamps fail to be controlled Troubleshooting Check the power in Check the power control program problems Check the lamp Check the lamp Check electric box s power transmission Check the power supply Check the cable connection Check the signal wire connection Check the first lamp which fails to be controlled 2. If trouble continues after checking the above causes, please contact our technicians promptly. GB Lamp Part1:General safety requirements and tests GB Lamp Part 2-1: Special requirements for fixed general lamps DuraComm Lighting Add: 6655 Troost Ave. Kansas City, MO 131 Tell: Web: 8