harley davidson motorcycle equipment installation manual
|
|
- Tyler Grant
- 6 years ago
- Views:
Transcription
1 harley davidson motorcycle equipment installation manual (All mounting systems included in this manual were designed specifically for the Electra-Glide Model Harley Davidson Motorcycle. A current 2008 model year bike was used for development) table of contents: 1. Front lighting option installations 2. Rear lighting option installations 3. Side lighting option installations 4. Radio Box lighting option installations 5. Siren installation options 6. Speaker installation IMPOR- Read all instructions and warnings before installing and using. IMPORTANT: INSTALLER: This manual must be delivered to the end user of this equipment.
2 Par 36 (7) led light head 1. Install the wiring terminations provided within the LED assembly. 2. Place retainer ring against back of LED housing with flat notch facing down to match up with clamshell on trim ring 3. Place trim ring over front of LED light and fully seat against flange of LED assembly. 4. Rotate LED assembly so that TOP indicated on LED lens is actually at the 12:00 O clock position on the bike, 5. Place the LED housing, trim ring and retainer onto light housing of bike. 6. Slide trim ring over retainer and into groove on light housing. 7. Tighten clamshell screw at bottom of LED light housing. Front Lighting Options Supervisor light bar 1. Remove two outboard windshield screws from front faring on bike. 2. Loosen center screw from front faring on bike. 3. Slide windscreen up and remove from front faring. (handle with care so not to scratch windscreen). 4. Loosely install two T56324 mounting brackets onto Supervisor outboard slots (threaded studs pointing upward & toward driver) 5. Slide center mounting bracket T56338 over center boss on faring with stud facing up and toward driver. 6. Place Supervisor so the center slot aligns with the center mounting bracket. 7. Feed outboard brackets down into windshield slot and over screw bosses (be sure bracket is around boss on faring.) 8. Tighten nylon locking nuts on end brackets (working both sides simultaneously) 9. Tighten center nylon nut on light bar base. 10. Slide windscreen down over center screw on faring, then feed each end of windscreen down over outboard bosses on faring. 11. Place two outboard faring screws back into faring bosses. (make sure to align screws with brass inserts within faring boss) 12. Tighten (3) faring /windscreen screws 13. Red wire is common power, White and Black wires are both negative ground. LED Supervisor Operation: (5) LED head light bar shown : LED s #1,3,& 5 are synchronized and LED s #2 & 4 are synchronized. Flash patterns are preset to triple flash P1 from the factory.
3 Front End Side Lighting Options Front fork led light head 1. Loosen top Fork Torx head bolt 2. Loosen bottom Fork Torx head bolt Note: Front Fork light assembly under Torx bolts will flex outward when loosened. It will be necessary to push light assembly inward during installation of front fork brackets. T56307 backing plate with pemserts Top 3. Place pemserted backing plate under chrome bracket with pemserts facing up into holes of chrome bracket 4. Place light head selection onto chrome bracket and attach using provided screws. (longer screws for XT3, shorter for LED-X light head options. Both are provided) 5. Slide vertical forked end of bracket under top Torx bolt 6. Slide horizontal forked end of bracket under bottom Torx bolt 7. Route wiring as desired behind front fork assembly, leaving sufficient loop for fork movement. T57066 Chrome bracket Bottom note: Motor guard lights can be mounted either vertically or horizontally on Motor guards. hd513 front fork light (xt3 led or led-ex) lxex125 with led-mhc2 motor guard light note: 1. Front fender bracket installed with finger of backing plate facing forward on bike, over top of black rubber foam inset. 2. Top of back plate must be under front fender edge to properly seat backing plate between rails. hd511 ( xt3 led) front fender light note: Mud flap bracket requires screw holes and wiring holes to be drilled into aluminum mud flap on front fender. Mud flap is sandwiched between the bracket and the light head once installed. Bracket is under Mud flap. hxt-mhc2 motor guard light (xt3 led) hd512 mud flap light (xt3 led)
4 On The Rail Rear Lighting Options Common Backing Plate and Bracket are used on all Rear lighting application options. T57098 Backing plate T57097 Bracket (Chrome) NOTE: All clamping parts of assembly to chrome rails require (1) anti-vibration pad T56311 to be installed at each contact point. T57098 BACKING PLATE T57097 CHROME BRACKET T15104 SS BOLT T03734 NYLOC NUT Optix 6-up light head assembly shown NOTE: hd2126 shown installed T56311 ANTI-VIBRATION PADS ARE REQUIRED AT ALL BRACKET MOUNT- ING POINTS IN CONTACT WITH CHROME RAILS OF BIKE. (8) ARE INCLUDED IN THE ASSEMBLY SHOWN. 1. Optix 3 up light head HD Dual Stack XT3 light head HD2103 HD2126 SHOWN CHROME BRACKETS, BACKING PLATES & HARDWARE ARE COMMON PARTS TO ALL ASSEMBLIES SHOWN BELOW. 2. Optix 6up light head hd2126 Rear License Plate Lighting 4. XT3 (3) way license plate bracket HDLPBKT Rear bracket installations are generally easier made with side saddle bags removed from bike.
5 Inside-The-Rail Side Lighting Options Common Backing Plate and Bracket are used on all inside-the-rail Side lighting application options. T57088 Backing plate T57087 Bracket (Chrome) NOTE: All clamping parts of assembly to chrome rails require (1) anti-vibration pad T56311 to be installed at each contact point. T57088 BACKING PLATE T57087 CHROME BRACKET T15104 BUTTON HEAD SS BOLT T15105 SS KEP NUT WITH STAR WASHER XT302 LIGHT HEAD ASSEMBLY SHOWN hd3126 shown installed NOTE: T56311 ANTI-VIBRATION PADS ARE REQUIRED AT ALL BRACKET MOUNT- ING POINTS IN CONTACT WITH CHROME RAILS OF BIKE. (8) ARE INCLUDED IN THE ASSEMBLY SHOWN. HD3102 SHOWN CHROME BRACKETS, BACKING PLATES & HARDWARE ARE COMMON PARTS TO ALL ASSEMBLIES SHOWN BELOW. 1. Optix 3 up light head HD Tandem LED-X light head HD XT302 light head assembly HD Optix 6 up light head hd Tandem XT3 light head assembly hd XT304 light head assembly hd3104 Inside-the-rail installations should be made with side saddle bags installed, by sliding backing plates in from forward end of rails. Bolts are installed with threads -out on assy.
6 Surface-Mount Side Lighting Options Common Backing Plate is used for all surface-mount side rail lighting application options. T57094 Backing plate NOTE: All clamping parts of assembly to chrome rails require (1) anti-vibration pad T56311 to be installed at each contact point. T03400 HEX HEAD SS BOLT T03734 NYLOC NUT T57094 BACKING PLATE OPTIX 6-UP DUAL STACK ASSEMBLY SHOWN hd3226 shown installed NOTE: T56311 ANTI-VIBRATION PADS ARE REQUIRED AT ALL BRACKET MOUNT- ING POINTS IN CONTACT WITH CHROME RAILS OF BIKE. (8) ARE INCLUDED IN THE ASSEMBLY SHOWN. HD3226 SHOWN CHROME BRACKETS ARE UNIQUE TO LIGHT HEAD SELECTION MADE. BACKING PLATES AND HARDWARE ARE COMMON TO ALL ASSEMBLIES SHOWN BELOW. 1. Optix 3 up Dual Stack light heads HD Tandem LED-X Dual Stack light heads HD Optix 6 up Dual Stack light heads hd Dual Stack LED-X light heads hd3228 Surface mounted Side brackets are installed with bolt threads facing in on assy. toward bike.
7 Radio Box Lighting Options REAR OF BOX: side of box: 1. XT304 light head assembly HD1104 XT302 & XT304 MOUNTINGS: 1. Aluminum backing plate is 1. XT304 light head assy. installed on the inside of the radio box. HD Black rubber grommets are between the U-shaped mounting bracket and the outside of the radio box. 3. Two rubber grommets are used on mounting bolt locations, One is used for power cord insertion point. 4. Power cord insertion point is off edge of backing plate on XT304 light installation. 5. When installing XT302 light head, the power cord is installed through the backing plate hole provided. 6. Mounting bolts are installed from the 2. TX302 light head assy. outside on both light assembly installations HD1102 and self- thread into the aluminum backing plates provided. 2. XT302 light head assembly HD LED-X Dual Stack light head lxex2f-bb or LXEX2F-RR or LXEX2F-BR on box support rails: 1. XT3 light head (Mounted with led down) (Mounted with led up) HD Optix 3up light head hd Optix 6up light head (Mounted with led up) (Mounted with led up) HD LED-X light head hd603 BOX SUPPORT BRACKETS FOR OPTIX LIGHT HEAD APPLICATIONS MUST BE ADJUSTED INBOARD UPON INSTALLATION SO LIGHT HEAD DOES NOT INTERFERE WITH SIDE SADDLE BAG OPENING. DEPENDING ON RADIO BOX SELECTED, USE OF OPTIX LIGHT HEAD BOX SUPPORT LIGHTS MAY REQUIRE THE BOX TO BE RAISED USING SPACERS, XT3 LIGHT HEAD APPLICATIONS CAN BE MADE WITHOUT SUCH INTERFE\RENCES.
8 Siren Selection siren options in the box: siren option on factory mount: Siren # 4022 Multi-Purpose Siren without PA Siren # 3955 Harley Davidson Waterproof Siren with PA Siren # 3959 Harley Davidson Siren with PA Mounts directly to Factory Installed Siren Plate. HDSPKT Complete Speaker Installation Kit Kit Includes: Speaker, Mounting Bracket, Mounting Hardware, Wiring Harness with Harley Davidson Connector Wiring Connector for LED Installations HD2PW 2 Pin Harley Davidson Power Connection kit is available for use on all light head installations and includes Housing, water seal and required pins.
9 NOtes: This page provided for installation notes
10 NOtes: This page provided for installation notes
11 NOtes: This page provided for installation notes
12 Warning! Larger wires and tight connections will provide longer service life for components. For high current wires it is highly recommended that terminal blocks or soldered connections be used with shrink tubing to protect the connections. Do not use insulation displacement connectors (e.g. 3M Scotchlock type connectors). Route wiring using grommets and sealant when passing through compartment walls. Minimize the number of splices to reduce voltage drop. High ambient temperatures (e.g. underhood) will significantly reduce the current carrying capacity of wires, fuses, and circuit breakers. Use "SXL" type wire in engine compartment. All wiring should conform to the minimum wire size and other recommendations of the manufacturer and be protected from moving parts and hot surfaces. Looms, grommets, cable ties, and similar installation hardware should be used to anchor and protect all wiring. Fuses or circuit breakers should be located as close to the power takeoff points as possible and properly sized to protect the wiring and devices. Particular attention should be paid to the location and method of making electrical connections and splices to protect these points from corrosion and loss of conductivity. Ground terminations should only be made to substantial chassis components, preferably directly to the vehicle battery. The user should install a fuse sized to approximately 125% of the maximum Amp capacity in the supply line to protect against short circuits. For example, a 30 Amp fuse should carry a maximum of 24 Amps. DO NOT USE 1/4" DIAMETER GLASS FUSES AS THEY ARE NOT SUITABLE FOR CONTINUOUS DUTY IN SIZES ABOVE 15 AMPS. Circuit breakers are very sensitive to high temperatures and will "false trip" when mounted in hot environments or operated close to their capacity. WARRANTY Code 3, Inc.'s emergency devices are tested and found to be operational at the time of manufacture. Provided they are installed and operated in accordance with manufacturer's recommendations, Code 3, Inc. guarantees all parts and components except the lamps to a period of 1 year (unless otherwise expressed) from the date of purchase or delivery, whichever is later. Units demonstrated to be defective within the warranty period will be repaired or replaced at the factory service center at no cost. Use of lamp or other electrical load of a wattage higher than installed or recommended by the factory, or use of inappropriate or inadequate wiring or circuit protection causes this warranty to become void. Failure or destruction of the product resulting from abuse or unusual use and/or accidents is not covered by this warranty. Code 3, Inc. shall in no way be liable for other damages including consequential, indirect or special damages whether loss is due to negligence or breach of warranty. CODE 3, inc. makes no other express or implied warranty including, without limitation, warranties of fitness or merchantability, with respect to this product. PRODUCT RETURNS If a product must be returned for repair or replacement*, please contact our factory to obtain a Return Goods Authorization Number (RGA number) before you ship the product to Code 3, Inc. Write the RGA number clearly on the package near the mailing label. Be sure you use sufficient packing materials to avoid damage to the product being returned while in transit. *Code 3, Inc. reserves the right to repair or replace at its discretion. Code 3, Inc. assumes no responsibility or liability for expenses incurred for the removal and /or reinstallation of products requiring service and/or repair.; nor for the packaging, handling, and shipping: nor for the handling of products return to sender after the service has been rendered. PROBLEMS OR QUESTIONS? CALL OUR TECHNICAL ASSISTANCE HOTLINE (314) Code 3, Inc N. Warson Road St. Louis, Missouri USA Ph. (314) Fax (314) Code 3 is a registered trademark of Code 3, Inc., a subsidiary of Public Safety Equipment, Inc. Part No. T56340 Rev. 0 06/ Code 3, Inc
S TROBE BEACO N INSTALLATION & OPERATION MANUAL MODEL 92XXX 12 JOULE MODEL 95XXX 15 JOULE MODEL 98XXX 8 JOULE MODEL 99XXX 20 JOULE FULL RANGE
INSTALLATION & OPERATION MANUAL FULL RANGE SERIES 90 MODEL 92XXX 12 JOULE MODEL 95XXX 15 JOULE MODEL 98XXX 8 JOULE MODEL 99XXX 20 JOULE FULL RANGE S TROBE BEACO N IMPORTANT: Contents: Introduction... 2
More informationINSTALLATION & OPERATION MANUAL
INSTALLATION & OPERATION MANUAL MODEL OL15F Patent Pending OSCILASER TM HEADLAMP MODULE Contents: Introduction... 2 Unpacking & Pre-Installation... 2 Installation & Mounting... 2-3 Maintenance... 4 Cleaning...
More informationINSTALLATION & OPERATION MANUAL
INSTALLATION & OPERATION MANUAL LED Duo Beam TM Introduction... 2 Unpacking & Pre-Installation...2 Installation & Mounting... 3 Wiring Instructions... 4 Maintenance... 4 Options & Specifcations...5-6 Flash
More information275 Beacon 12v MODELS PERMANENT, MAGNETIC MOUNT BEACONS
INSTALLATION & OPERATION MANUAL 275/275AH/275ASH/ 275AMH BEACON 275 Beacon 12v MODELS PERMANENT, MAGNETIC MOUNT BEACONS Contents: Introduction... 2 Unpacking & Pre-Installation... 2 Installation & Mounting...
More informationINSTALLATION & OPERATION MANUAL
INSTALLATION & OPERATION MANUAL SuperVisorTL IMPORTANT: SuperVisorTL Interior Lighting System 2011 Ford F150 CONTENTS: Introduction... 2 Unpacking & Pre-Installation...2 Installation & Mounting...3-4 Wiring
More informationINSTALLATION & OPERATION MANUAL
INSTALLATION & OPERATION MANUAL SUPERVISOR TL SuperVisor TL Interior Lighting System Chevrolet Tahoe 2007 Model CONTENTS: Introduction... 2 Unpacking & Pre-Installation... 2 Installation & Mounting...
More informationINSTALLATION & OPERATION MANUAL. WingMan. WingMan. Interior Lighting System FORD CROWN VICTORIA UPPER REAR DECK LIGHT BAR IMPORTANT: CONTENTS:
INSTALLATION & OPERATION MANUAL WingMan CONTENTS: WingMan Interior Lighting System FORD CROWN VICTORIA UPPER REAR DECK LIGHT BAR Introduction... 2 Unpacking & Pre-Installation... 2 Installation & Mounting...
More informationINSTALLATION & OPERATION MANUAL
INSTALLATION & OPERATION MANUAL SUPERVISOR TL SuperVisor TL Interior Lighting System Expedition 2007 Model CONTENTS: Introduction... 2 Unpacking & Pre-Installation... 2 Installation & Mounting... 3-4 Wiring
More informationModel 550 TM INSTALLATION & OPERATION MANUAL
INSTALLATION & OPERATION MANUAL MODEL 550 TM Model 550 TM REVOLVING BEACON Contents: Introduction... 2 Unpacking & Pre-Installation... 2 Installation & Mounting... 2 Wiring Instructions... 2 Stanchion
More informationModel FM100 INSTALLATION & OPERATION MANUAL SPEAKER/FLUSHMOUNT IMPORTANT: MODEL FM100C OR FM100V Patent Pending
INSTALLATION & OPERATION MANUAL MODEL FM100C OR FM100V Patent Pending Model FM100 SPEAKER/FLUSHMOUNT Contents: Introduction... 2 Unpacking & Pre-Installation... 3 Installation & Mounting... 3 Maintenance...
More informationINSTALLATION MANUALS FOR THE SUPERVISOR. Click below to go to the appropriate model. For all others, contact Customer Service at (314)
INSTALLATION MANUALS FOR THE SUPERVISOR Click below to go to the appropriate model. For all others, contact Customer Service at (314) 426-2700. Ford Crown Victoria Chevy Impala Ford Explorer Chevy Tahoe
More informationINSTALLATION & OPERATION MANUAL
INSTALLATION & OPERATION MANUAL MODEL PB100 Patent Pending CONTENTS: Introduction... 2 Installation & Mounting... 2-3 Maintenance... 4 Parts List... 5 Troubleshooting... 5 Warranty... 8 IMPORTANT: Read
More informationFX817 INSTALLATION & OPERATION MANUAL IMPORTANT:
INSTALLATION & OPERATION MANUAL FX817 Contents: Introduction...2 Features and Specifications...2 Current Draw...2 Installation & Mounting...3 Wiring...3 Operation...4 Maintenance...4 Troubleshooting...4
More informationINSTALLATION & OPERATION MANUAL
INSTALLATION & OPERATION MANUAL Standard Version Lighted Version IMPORTANT: LIT3 Mounting Kit CONTENTS: Introduction...2 Unpacking and Pre-Installation...2 Installation and Mounting-Standard Mount...2-8
More informationINSTALLATION & OPERATION MANUAL. WingMan. WingMan IMPORTANT: Interior Lighting System Crown Victoria REAR DECK LIGHT BAR
INSTALLATION & OPERATION MANUAL SHORT VERSION WingMan LONG VERSION WingMan Interior Lighting System Crown Victoria REAR DECK LIGHT BAR CONTENTS: Introduction... 2 Unpacking & Pre-Installation... 2 Installation
More informationINSTALLATION & OPERATION MANUAL
INSTALLATION & OPERATION MANUAL NON DOME LIGHT VERSION DOME LIGHT VERSION SuperVisor-MC - 2011 Dodge Charger With Multi Color Torus Technology Interior Lighting System CONTENTS: Introduction... 2. Unpacking
More information21IF TM INSTALLATION & OPERATION MANUAL LIGHTBAR IMPORTANT: 21IF TM LIGHTBAR CONTENTS:
INSTALLATION & OPERATION MANUAL 2IF TM LIGHTBAR CONTENTS: 2IF TM LIGHTBAR Introduction...2 Unpacking & Pre-Installation...2 Installation & Mounting...3-4 Wiring Instructions & Fusing...5-6 Setting Flash
More informationRX2700 INSTALLATION & OPERATION MANUAL LIGHT BAR IMPORTANT: FOR RX2700 LIGHTBAR
INSTALLATION & OPERATION MANUAL FOR RX2700 LIGHTBAR RX2700 LIGHT BAR CONTENTS: Introduction...2 Unpacking & Pre-Installation...3 Installation & Mounting...3 Wiring Instructions...3-4 Options & Specifications...4-6
More informationInstallation and Operation Instructions Safety Director Arrow
Installation and Operation Instructions Safety Director Arrow! WARNING! Failure to install or use this product according to manufacturers recommendations may result in property damage, serious bodily/personal
More informationSERIES 45, 65, 85 LED PERIMETER, INSTALLATION & OPERATION MANUAL STOP/TURN/TAIL LED PERIMETER, STOP/TURN/TAIL SERIES 45, 65, 85.
INSTALLATION & OPERATION MANUAL LED PERIMETER, STOP/TURN/TAIL SERIES 45, 65, 85 SERIES 45, 65, 85 LED PERIMETER, Contents: STOP/TURN/TAIL Introduction... 2 Unpacking & Pre-Installation... 2 Mounting Options...
More informationRX 2700 INSTALLATION & OPERATION MANUAL IMPORTANT:
INSTALLATION & OPERATION MANUAL FOR RX 2700 lightbar WITH PRIZM II LIGHT HEADS RX 2700 LIGHT BAR CONTENTS: Introduction...2 Unpacking & Pre-Installation...3 Installation & Mounting...3 Wiring Instructions...3-4
More information420 Series Beacon INSTALLATION &OPERATION MANUAL. 12/24v MODELS PERMANENT AND MAGNETIC LED AND STROBE BEACONS IMPORTANT: 420 BEACON 425 BEACON
INSTALLATION &OPERATION MANUAL 420 BEACON 425 BEACON 420 Series Beacon 12/24v MODELS PERMANENT AND MAGNETIC LED AND STROBE BEACONS Contents: Introduction...2 Unpacking & Pre-Installation...2 Installation
More informationINSTALLATION MANUAL IMPORTANT:
INSTALLATION MANUAL Introduction......2 CONTENTS: Installation, Mounting, & Wiring......3-5 Wiring Diagram Package 1......6 Wiring Diagram Package 2......7 Wiring Diagram Package 3......8 Wiring Diagram
More informationSERIES 80/81/82 STROBE AND HALOGEN PERIMETER LIGHT HEADS INSTALLATION & OPERATION MANUAL IMPORTANT: SERIES 80/81/82 STROBE AND HALOGEN
INSTALLATION & OPERATION MANUAL SERIES 80/81/82 STROBE AND HALOGEN PERIMETER LIGHT HEADS SERIES 80/81/82 STROBE AND HALOGEN PERIMETER LIGHT HEADS Contents: Introduction... 2 Unpacking & Pre-Installation...
More informationDo not install and/or operate this safety product unless you have read and understand the safety information contained in this manual.
Installation and Operation Instructions MR Tri- Light Available in various color combinations, the MR Directional LED surface mount, tri-color warning light is ideal for a wide variety of auxiliary warning
More informationNOTE. Figure 2. Mounting Configurations (View shown from rear of LED Bar) Figure 3. Rear Deck Mounting NOTE
Page 5 Page 6 TO REAR OF VEHICLE (STANDARD WIRING) LIGHTBAR 2 TO FRONT OF VEHICLE (OPTIONAL WIRING) LIGHTBAR 1 LIGHTBAR 1 LIGHTBAR 2 Figure 2. Mounting Configurations (View shown from rear of LED Bar)
More informationNOTE. Figure 2. Mounting Configurations (View shown from rear of LED Bar) Figure 3. Rear Deck Mounting NOTE
Page 5 Page 6 TO REAR OF VEHICLE (STANDARD WIRING) LIGHTBAR 2 TO FRONT OF VEHICLE (OPTIONAL WIRING) LIGHTBAR 1 LIGHTBAR 1 LIGHTBAR 2 Figure 2. Mounting Configurations (View shown from rear of LED Bar)
More informationENFORCER TM 6201-IQ ELECTRONIC SIREN
ENFORCER TM 6201-IQ ELECTRONIC SIREN INSTALLATION & OPERATION MANUAL CONTENT PAGE UNPACKING 2 INTRODUCTION 2 STANDARD FEATURES 2 INSTALLATION & MOUNTING 3 MOUNTING THE ENFORCER TM 6201 3 WIRING & ADJUSTMENTS
More information37SCENE 46SCENE 79SCENE
Installation and Operation Instructions LED SCENE LIGHT LED SCENE LIGHT 37SCENE 46SCENE 79SCENE 37SCENE 46SCENE Introduction The 37SCENE, 46SCENE, 79SCENE LED Scene Lights are designed for the emergency
More informationw w w. h d o n l i n e s h o p. d e ELECTRA-GLO LIGHT BARS GENERAL INSTALLATION -J04723 REV Kit Number Models Kit Contents
-J07 REV. 00-0-0 GENERAL Kit Number -09 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only). Kit Contents See
More informationMR6F LED Windshield Lights
MR6F LED Windshield Lights INSTALLATION INSTRUCTION MR6F-X/X-WL TABLE OF CONTENTS: Models.2 Introduction.2 General Warnings...2 Unpacking & Pre-Installation Check..3 Installation..4 Wiring Instructions.4
More informationI N S TA L L AT I O N
I N S TA L L AT I O N 5008 fits: H-D: '80-Up Electra glide, tour glide, road king, road glide or street glide PartS Included 1 Right Fork Mount Assembly 1 Left Fork Mount Assembly 2 H3 Driving Light Assemblies
More informationINSTALLATION & OPERATION MANUAL. for DEFENDER Light bars DEFENDER. U.S. Patent Nos. 7,153,015 and 7,300,175 - Other Patents Pending
INSTALLATION & OPERATION MANUAL for DEFENDER Light bars DEFENDER LIGHT BAR with TRICORE and Tricore tc 2 TECHNOLOGY U.S. Patent Nos. 7,153,015 and 7,300,175 - Other Patents Pending CONTENTS: Introduction...2
More informationSTL Mounting Brackets
2809 Business Park Dr Buda TX 78610 Phone 800.757.2581 Fax 844.894.2652 Email customerservice@speedtechlights.com STL Mounting Brackets Operation Manual and Instructions Congratulations, you are the owner
More informationInstallation and Operation Instructions Evolution Series Light Bars (36-72 )
Installation and Operation Instructions Evolution Series Light Bars (36-72 ) IMPORTANT! Read all instructions before installing and using. Installer: This manual must be delivered to the end user.! WARNING!
More informationEquipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:21-8125 2011-2012 Ford F150 V8 5.0L * NOTE: Legal in California only for racing vehicles which may never be used
More informationInstallation and Operation Instructions C5550 Series LED Microbars
Installation and Operation Instructions C5550 Series LED Microbars C5550 Series - Reflex LED microbars provide a compact yet powerful warning solution that offers the flexibility of either permanent, or
More informationIMPORTANT R 1200 RT-P BMW LIGHTING PACKAGE (2015+)
R 1200 RT-P BMW LIGHTING PACKAGE (2015+) Contents: Installation (Front Pod) Adding Lightheads...Page 2 Installation (Front Pod) ing to Stalk...Page 3 Installation (Rear Pod) ing Base to Radio Box Cover...
More informationSTL K-Force 18 and Micro 14 LED Mini Light Bar
2809 Business Park Dr Buda TX 78610 Phone 800.757.2581 Fax 844.894.2652 Email customerservice@speedtechlights.com STL K-Force 18 and Micro 14 LED Mini Light Bar Operation Manual and Instructions Congratulations,
More informationSPORTSTER SADDLEBAG KIT. i i02212
General These saddlebags are designed to fit 99 and later Sportster Model Motorcycles, except XL00 Sport models with gas reservoir shock absorbers and 88R models. See the Service Parts pages for a list
More informationContents. IMPORTANT! Read all instructions before installing and using. Installer: This manual must be delivered to the end user.
Installation and Operation Instructions Pursuit Lightbar Introduction The Pursuit Lightbar is a versatile, powerful, high output warning device suitable for a range of vehicle types and duties. There are
More informationINSTRUCTIONS. w w w. h d o n l i n e s h o p. d e SPRINGER AUXILIARY LAMP KIT 1WARNING -J03497 REV General.
INSTRUCTIONS -J097 REV. 0-0-00 Kit Number 6986-0A General Auxiliary/fog lamps are not included in this kit. The lamps must be purchased separately. HDI (International) motorcycles should only use approved
More informationINSTRUCTIONS. w w w. h d o n l i n e s h o p. d e ENGINE GUARD-MOUNTED FOG LAMP KIT 1WARNING -J02798 REV Installation.
INSTRUCTIONS -J0798 REV. 9-4-00 Kit Number 689-98B General ENGINE GUARD-MOUNTED FOG LAMP KIT Installation This kit fits all models equipped with Harley-Davidson -/4 in. ( mm) diameter front engine guards,
More informationROAD TECH ZUMO GLOBAL POSITIONING SYSTEM (GPS) HANDLE- BAR MOUNT KIT
-J046 REV. 008-08- ROAD TECH ZUMO GLOBAL POSITIONING SYSTEM (GPS) HANDLE- BAR MOUNT KIT GENERAL Kit Number 965-08 Models This kit is required when using a Road Tech Zumo GPS unit on specific model motorcycles.
More informationSTL Striker /Virtue Interior LED Traffic Series
2809 Business Park Dr Buda TX 78610 Phone 800.757.2581 Fax 844.894.2652 Email customerservice@speedtechlights.com STL Striker /Virtue Interior LED Traffic Series Operation Manual and Instructions Congratulations,
More informationSTL Ceptor Series Running Board Light Stick
2809 Business Park Dr Buda TX 78610 Phone 800.757.2581 Fax 844.894.2652 Email customerservice@speedtechlights.com STL Ceptor Series Running Board Light Stick Operation Manual and Instructions Congratulations,
More informationInstallation Instructions PowerBoard Automatic Retracting Running Board
Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Chevy Silverado/GMC Sierra Extended Cab Diesel 2011 and newer Part Number: 75147-15 Chevy Silverado/GMC Sierra
More informationINSTRUCTIONS FLHT 1998 AND LATER MODELS RADIO/CD KIT 1WARNING -J02911 REV General. Installation. Outer Fairing Removal
MPH CERTIFIED HARLEY-DAVIDSON UNLOCK RPMx00 HARLEY-DAVIDSON INSTRUCTIONS REV. 5--0 Kit Numbers 760-0A (Domestic) and 769-0A (HDI) General FLHT 998 AND LATER MODELS RADIO/CD KIT This radio kit fits 998
More informationINSTALLATION FORK MOUNTED DRIVING LIGHTS 5008
5008 PARTS INCLUDED 1 Right Fork Mount Assembly 1 Left Fork Mount Assembly 2 H3 Driving Light Assemblies 1 12-Pin Wiring Adapter 1 Hardware Kit for Fork Mount Driving Lights, Including: 6 5/16-18 Nylock
More informationw w w. h d o n l i n e s h o p. d e STREET SLAMMER HANDLEBAR KIT GENERAL INSTALLATION -J03363 REV Kit Number Models Kit Contents
-J06 REV. 006-06- GENERAL Kit Number 69-0 Models STREET SLAMMER HANDLEBAR KIT Ask a Harley-Davidson dealer or refer to the latest Harley- Davidson Genuine Motor Accessories and Genuine Motor Parts catalog
More informationSTL Raptor Series Interior LED Visor Light Bar
2809 Business Park Dr Buda TX 78610 Phone 800.757.2581 Fax 844.894.2652 Email customerservice@speedtechlights.com STL Raptor Series Interior LED Visor Light Bar Operation Manual and Instructions Congratulations,
More informationSTL Raptor - X TIR Interior LED Visor Light Bar
2809 Business Park Dr Buda TX 78610 Phone 800.757.2581 Fax 844.894.2652 Email customerservice@speedtechlights.com STL Raptor - X TIR Interior LED Visor Light Bar Operation Manual and Instructions Congratulations,
More informationMCL-3000 SERIES AIR PRESSURE PART# MCL-3K-A
MCL-3000 SERIES AIR PRESSURE PART# MCL-3K-A Thank you for purchasing the Dakota Digital MCL-3K-A gauge for your Harley Davidson Touring bike. This gauge is designed to be a direct, plug in replacement
More informationInstallation and Operation Instructions 1200 Series Vantage Lightbars
Installation and Operation Instructions 1200 Series Vantage Lightbars *Optional Controller Contents: Introduction 1 Unpacking and Pre-Installation 1 Installation and Mounting 2 Wiring Instructions 5 Options
More informationInstallation Instructions PowerBoard Automatic Retracting Running Board
Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Chevy Silverado/GMC Sierra Extended Cab 2007 and newer (excluding 2011 Diesels) Part Number: 75123-15 Chevy Silverado/GMC
More informationw w w. h d o n l i n e s h o p. d e CHROME FAN KIT GENERAL INSTALLATION -J04347 REV Kit Number Models Kit Contents
-J0447 REV. 008-08-05 CHROME FAN KIT GENERAL Kit Number 996-08 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English
More informationINSTALLATION. DRIVING LIGHTS for FLHT/FLHX/FLHR BLACK. THANK YOU FOR CHOOSING KϋRYAKYN!
THANK YOU FOR CHOOSING KϋRYAKYN! PROTECT YOURSELF AND OTHERS FROM POSSIBLE INJURY AND PROPERTY DAMAGE OR LOSS. PAY CLOSE ATTENTION TO ALL INSTRUCTIONS, WARNINGS, CAUTIONS, AND NOTICES REGARDING THE, USE,
More informationEquipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: DS (Plastic Intake Tube)
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:21-8126DS (Plastic Intake Tube) 2011-2014 Ford F150 V6 3.5L ECOBOOST C.A.R.B. E.O. D-670-19 AEM Induction Systems
More informationHI-FLOW FUEL RAIL. Installation Instructions for Scion tc & xb AEM Fuel Rail AN Hose adaptor
HI-FLOW FUEL RAIL Installation Instructions for 08-10 Scion tc & xb 25-170 AEM Fuel Rail 2-661 -6 AN Hose adaptor AEM Performance Electronics INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:
More informationInstallation Instructions PowerBoard Automatic Retracting Running Board
Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Chevy Silverado/GMC Sierra Extended Cab 2007 and newer (excluding 2011 Diesels) Part Number: 75123-15 Chevy Silverado/GMC
More informationBoss Frog Installation Instructions Single Hoop Rollbar for Mazda Miata
Boss Frog Installation Instructions Single Hoop Rollbar for Mazda Miata Introduction Congratulations! You have purchased one of the highest quality rollbars available today. Installing your new rollbar
More informationSprinter Van A
I N S T A L L A T I O N G U I D E APPLICATION MODEL YR PART # Sprinter Van 2007-2016 75163-01A INSTALLATION TIME 3-5 Hours Professional installation recommended SKILL LEVEL 1 2 3 4 4= Experienced TOOLS
More informationHarley-Davidson. Police Lighting & Warning Products
Harley-Davidson Police Lighting & Warning Products Harley-Davidson Police Lighting and Warning Products Whelen has engineered a wide variety of specialized Harley Davidson Police products to fully customize
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Accent light Kit Versa Note 999F3 4Z000 - Accent Lighting Kit. 999Q9 AY000 - Accessory Service Connector
More informationAMP RESEARCH TECH SUPPORT (Press 2) Monday - Friday, 6:00 AM - 5:00 PM PST
APPLICATION AMP Part # Jeep Wrangler Unlimited (JK) 2007 2017 78122-01A (-Door Only) INSTALLATION TIME 3-5 Hours Professional installation recommended SKILL LEVEL 1 2 3 = Experienced TOOLS REQUIRED q 13
More informationPART NUMBER: MINI Cooper S L4-1.6L SEE * NOTE
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-699 2007-2010 MINI Cooper S L4-1.6L SEE * NOTE * NOTE: Legal in California only for racing vehicles which may
More informationI N S T A L L A T I O N G U I D E
I N S T A L L A T I O N G U I D E APPLICATION AMP Part # Jeep Wrangler Unlimited (JK) 2007 2017 78122-01A (4-Door Only) INSTALLATION TIME 3-5 Hours Professional installation recommended SKILL LEVEL 1 2
More informationINSTALLATION. DRIVING LIGHTS for FLHT/FLHX/FLHR 5005
DRIVING LIGHTS for FLHT/FLHX/FLHR 5005 PARTS INCLUDED 1 Right Driving Light Assembly 1 Left Driving Light Assembly 1 Right Driving Light Bracket 1 Left Driving Light Bracket 4 Driving Light Bracket Plugs
More informationInstallation MKIV Headlight Housings with Fog Lamps (Procedures apply to both MKIV Jetta and Golf)
Page 1 This tutorial is provided as a courtesy by ECS Tuning. Service Procedure Installation Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well
More informationINSTALLATION GUIDE. AMP RESEARCH TECH SUPPORT (Press 2) Monday - Friday, 6:00 AM - 5:00 PM PST
INSTALLATION GUIDE APPLICATION AMP Part # Jeep Wrangler Unlimited (JK) 2007 up 75121-01A 2-Door INSTALLATION TIME 3-5 Hours Professional installation recommended SKILL LEVEL 1 2 3 = Experienced TOOLS REQUIRED
More informationw w w. h d o n l i n e s h o p. d e ROAD TECH QUEST GLOBAL POSITIONING SYSTEM (GPS) MOUNTING KIT GENERAL INSTALLATION -J03554 REV.
-J03554 REV. 007-08-0 ROAD TECH QUEST GLOBAL POSITIONING SYSTEM (GPS) MOUNTING KIT GENERAL Kit Number 900-05 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories
More informationSADDLEBAG AUDIO WIRE HARNESS KIT P/N
SADDLEBAG AUDIO WIRE HARNESS KIT P/N 2880986 APPLICATION ALL INDIAN MOTORCYCLES WITH BOTH TRUNK AND SADDLEBAG AUDIO INSTALLED BEFORE YOU BEGIN Read these instructions and check to be sure all parts and
More informationDIRECT PLUS/FLEX/MAX INSTALLATION GUIDE. INST165 Doc 1.04
DIRECT PLUS/FLEX/MAX INSTALLATION GUIDE INST165 Doc 1.04 CONTENTS General Information...2 Diagrams...3 Mounting the Direct Nosebox...5 Main Harness Installation...6 Interior Light Harness Installation...10
More informationPage 1. File: Motolight caliper one-piece Harley Date: 8/15/2006
Page 1 Harley-Davidson FL Caliper Mount Installation One-piece mounting brackets You should allow about two to three hours for installation. We suggest you use a well-lighted space for installation. PLEASE
More information3-5 Hours Professional installation recommended
I N S T A L L A T I O N G U I D E APPLICATION AMP Part # Chevrolet Silverado 2500/3500 / GMC Sierra 2500/3500 - Ext. Cab * 2007-201 75126-01A Chevrolet Silverado 2500/3500 / GMC Sierra 2500/3500 - Crew
More informationFITTING KIT No s : BULL BAR WINCH ( P/No ) BULL BAR NON WINCH ( P/No )
ARB WINCH / NON WINCH BULL BAR TO SUIT LANDROVER DISCOVERY 2003 ONWARD. FITTING KIT No s :- 617 1793 BULL BAR WINCH ( P/No 343 2120 ) 617 1794 BULL BAR NON WINCH ( P/No 323 2120 ) WARNING FOR VEHICLES
More informationGM 6.6L Duramax. Up to 90HP Gain. AgDieselSolutions.com
21700 Module Installation Guide 2017 GM 6.6L Duramax *L5P* Up to 90HP Gain 1-3 MPG Fuel Savings AgDieselSolutions.com Adjustable Switch Female Fuel Pressure Sensor Connector Male Fuel Pressure Sensor Connector
More informationDetroit Speed, Inc. Selecta-Speed Wiper Kit Corvette P/N:
Detroit Speed, Inc. Selecta-Speed Wiper Kit 1963-67 Corvette P/N: 121620 A downpour of rain will no longer hinder your ability to clearly see the road. The Detroit Speed Selecta-Speed Wiper Kit provides
More informationw w w. h d o n l i n e s h o p. d e ROAD KING FAT HANDLEBAR KIT GENERAL PREPARATION - ALL MODELS -J02375 REV Kit Number Models ABS Models
-J02375 REV. 2008--9 GENERAL Kit Number 56675-05 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only). ABS Models
More informationI N S T A L L A T I O N G U I D E. Chevrolet Silverado / GMC Sierra - Ext Cab * A (Diesel Only)
I N S T A L L A T I O N G U I D E APPLICATION AMP Part # Chevrolet Silverado / GMC Sierra - Crew Cab 2011-201 751-01A (Diesel Only) Chevrolet Silverado / GMC Sierra - Ext Cab 2011-201* 751-01A (Diesel
More informationSOLAR BOLT CHARGING SYSTEM INSTALLATION GUIDE
CHARGING SYSTEM Doc 1.00 INST052 1 SOLAR BOLT CHARGING SYSTEM CONTENTS General Information... 2 Solar Panel Installation... 3 Solar Bolt Main Harness and Indicate Installation... 4 Cable Routing... 9 Solar
More informationw w w. h d o n l i n e s h o p. d e CRUISE CONTROL KIT GENERAL INSTALLATION -J04064 REV Kit Number Models Additional Parts Required
-J006 REV. 006-08- CRUISE CONTROL KIT GENERAL Kit Number 7796-07 Models For the most up-to-date model fitment information, please see the product label or www.harley-davidson.com. Additional Parts Required.
More informationLED FLASHER GND CONTROL FPC4N
LED FLASHER GND CONTROL FPC4N Installation/Operations Manual FPC4N Table of Contents Applicable Models... 2 Introduction... 2 General Warnings... 2 Unpacking &Pre-Installation Check... 3 Installation &
More informationINSTALLATION GUIDE. AMP RESEARCH TECH SUPPORT (Press 2) Monday - Friday, 6:00 AM - 5:00 PM PST
INSTALLATION GUIDE APPLICATION AMP Part # Jeep Wrangler Unlimited (JK) 2007 2015 75122-01A (-Door Only) INSTALLATION TIME 3-5 Hours Professional installation recommended SKILL LEVEL 1 2 3 = Experienced
More informationJAMP-250HR06P. Installation and Operation Instructions. 250W Amplifier Kit For Harley RoadGlide Fairing
250W Amplifier Kit For 2006-2013 Harley RoadGlide Fairing # JAMP-250HR06P 2013 J&M Corporation. All rights reserved. 5/13 Installation and Operation Instructions Product Description This exciting new J&M
More information30 Meter Add-On Kit for the DXE-8040VA-1 Vertical Antenna
30 Meter Add-On Kit for the DXE-8040VA-1 Vertical Antenna DXE-8040-30AOK DXE-8040-30AOK-INS Revision 0d DX Engineering 2017 1200 Southeast Ave. - Tallmadge, OH 44278 Phone: (800) 777-0703 Tech Support
More informationI N S T A L L A T I O N G U I D E. AMP RESEARCH TECH SUPPORT (Press 2) Monday - Friday, 6:00 AM - 5:00 PM PST
I N S T A L L A T I O N G U I D E APPLICATION AMP Part # Jeep Wrangler Unlimited (JK) 2007 2014 75121-01A 2-Door INSTALLATION TIME 3-5 Hours Professional installation recommended SKILL LEVEL 1 2 3 4 4=
More informationI N S T A L L A T I O N G U I D E. AMP RESEARCH TECH SUPPORT (Press 2) Monday - Friday, 6:00 AM - 5:00 PM PST
I N S T A L L A T I O N G U I D E APPLICATION AMP Part # Jeep Wrangler Unlimited (JK) 2007 2017 78121-01A 2-Door INSTALLATION TIME 3-5 Hours Professional installation recommended SKILL LEVEL 1 2 3 4 4=
More informationSTL Raptor Linear Interior LED Visor Light Bar
2809 Business Park Dr Buda TX 78610 Phone 800.757.2581 Fax 844.894.2652 Email customerservice@speedtechlights.com STL Raptor Linear Interior LED Visor Light Bar Operation Manual and Instructions Congratulations,
More informationAmp & Speaker Upgrade Install Instructions for Batwing Fairing
Amp & Speaker Upgrade Install Instructions for Batwing Fairing Tools Needed: 1/2 inch Socket Wire Cutters 7/16 inch Socket Wire Strippers 10 mm Socket Phillips Screwdriver 1/2 inch Ratchet Wrench T25 Torx
More informationDo not install and/or operate this safety product unless you have read and understand the safety information contained
Installation and Operation Instructions ED3766 TRI Color Directional LED Available in various color combinations, the ED3766 Directional LED is a surface mount, tri-color warning light that is ideal for
More informationw w w. h d o n l i n e s h o p. d e HEATED HAND GRIP KITS GENERAL REMOVAL -J02983 REV Kit Number Models Kit numbers Service Parts
-J098 REV. 007-0-0 GENERAL Kit Number 56047-0B, 5607-0B, 5674-0B, 5696-0B, 565-0B, 5669-0A, 56694-04A, 56750-04A, 5688-0A, 569-05, 5696-05, 56997-07 Models For model fitment information, please see the
More informationDetroit Speed, Inc. Selecta-Speed Wiper Kit Mustang P/N:
Detroit Speed, Inc. Selecta-Speed Wiper Kit 1967-68 Mustang P/N: 121651 A downpour of rain will no longer hinder your ability to clearly see the road. The Detroit Speed Inc. Selecta-Speed Wiper Kit provides
More informationINSTALLATION INSTRUCTIONS Horizon XP Performance Handlebar
INSTALLATION INSTRUCTIONS Horizon XP Performance Handlebar HZ10090XP, HZ10090XP-BA (1 Mount) Gen 1 HZ10093XP, HZ10093XP-BA (1 1/4 Mount) Gen 1 HZ10096XP, HZ10096XP-BA ( 1 1/4 Mount) Gen 2 HZ10097XP, HZ10097XP-BA
More informationEquipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: DS
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:21-8126DS 2011-2013 Ford F150 V6 3.5L ECOBOOST * NOTE: Legal in California only for racing vehicles which may never
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Security Light Kit APPLICATION: Altima Sedan (2013+) PART NUMBER: 999F4 AX010 - Universal Security Lighting Kit. KIT CONTENTS: Item QTY
More informationINSTALLATION INSTRUCTIONS FOR THE MOTOR TRIKE GL1500 RAKE KIT
INSTALLATION INSTRUCTIONS FOR THE MOTOR TRIKE GL1500 RAKE KIT Thank you for choosing the Motor Trike GL1500 Rake Kit. We ask that you read the directions before you start and follow them very closely.
More informationU L T I M A T E R A D A R / L A S E R D E F E N S E S Y S T E M
S m a r t e r Q u i e t e r M o r e A c c u r a t e U L T I M A T E R A D A R / L A S E R D E F E N S E S Y S T E M Installation Manual PASSPORT 9500ci Comes Complete Front Radar Receiver Miniature weatherproof
More informationINSTALLATION GUIDE. AMP RESEARCH TECH SUPPORT (Press 2) Monday - Friday, 6:00 AM - 5:00 PM PST
INSTALLATION GUIDE APPLICATION AMP Part # Jeep Wrangler Unlimited (JK) 2007 up 751-01A 2-Door INSTALLATION TIME 3-5 Hours Professional installation recommended SKILL LEVEL 1 2 3 = Experienced TOOLS REQUIRED
More informationDetroit Speed, Inc. Selecta-Speed Wiper Kit Corvette P/N:
Detroit Speed, Inc. Selecta-Speed Wiper Kit 1968-72 Corvette P/N: 121621 A downpour of rain will no longer hinder your ability to clearly see the road. The Detroit Speed Selecta-Speed Wiper Kit provides
More information